From f5786b8e934e77f76f689c515baa582ff5a196ec Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Fri, 21 Jun 2013 15:36:11 +0200 Subject: ARM i.MX53: Fix UART pad configuration The current default pad configuration for UART RX and TX pads sets a 360k pull-down and writes 1 to a reserved bit (1 << 0). It doesn't seem right to me that in idle state, the UART has to keep the signal high against a pull-down resistor. This patch instead sets a 100k pull-up, which incidentally corresponds to the register reset value for all but one (MX53_PAD_KEY_ROW0__UART4_RXD_MUX) pad, and removes the write to the reserved bit. Signed-off-by: Philipp Zabel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx53.dtsi | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi index 3895fbba8fc..569aa9f2c4e 100644 --- a/arch/arm/boot/dts/imx53.dtsi +++ b/arch/arm/boot/dts/imx53.dtsi @@ -725,15 +725,15 @@ uart1 { pinctrl_uart1_1: uart1grp-1 { fsl,pins = < - MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1c5 - MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1c5 + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4 + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4 >; }; pinctrl_uart1_2: uart1grp-2 { fsl,pins = < - MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1c5 - MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1c5 + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 >; }; @@ -748,8 +748,8 @@ uart2 { pinctrl_uart2_1: uart2grp-1 { fsl,pins = < - MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1c5 - MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1c5 + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 >; }; @@ -766,17 +766,17 @@ uart3 { pinctrl_uart3_1: uart3grp-1 { fsl,pins = < - MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1c5 - MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1c5 - MX53_PAD_PATA_DA_1__UART3_CTS 0x1c5 - MX53_PAD_PATA_DA_2__UART3_RTS 0x1c5 + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 + MX53_PAD_PATA_DA_1__UART3_CTS 0x1e4 + MX53_PAD_PATA_DA_2__UART3_RTS 0x1e4 >; }; pinctrl_uart3_2: uart3grp-2 { fsl,pins = < - MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1c5 - MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1c5 + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 >; }; @@ -785,8 +785,8 @@ uart4 { pinctrl_uart4_1: uart4grp-1 { fsl,pins = < - MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1c5 - MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1c5 + MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1e4 + MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1e4 >; }; }; @@ -794,8 +794,8 @@ uart5 { pinctrl_uart5_1: uart5grp-1 { fsl,pins = < - MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1c5 - MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1c5 + MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1e4 + MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1e4 >; }; }; -- cgit v1.2.3-70-g09d2 From 0d5ca6d973b54f76eaccf86116dd0c66b073afc5 Mon Sep 17 00:00:00 2001 From: Alexander Shiyan Date: Sun, 23 Jun 2013 17:40:35 +0400 Subject: ARM: i.MX27: Typo fix Signed-off-by: Alexander Shiyan Acked-by: Sascha Hauer Signed-off-by: Shawn Guo --- arch/arm/mach-imx/mx27.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-imx/mx27.h b/arch/arm/mach-imx/mx27.h index e074616d54c..8a65f192e7f 100644 --- a/arch/arm/mach-imx/mx27.h +++ b/arch/arm/mach-imx/mx27.h @@ -135,7 +135,7 @@ #define MX27_INT_GPT4 (NR_IRQS_LEGACY + 4) #define MX27_INT_RTIC (NR_IRQS_LEGACY + 5) #define MX27_INT_CSPI3 (NR_IRQS_LEGACY + 6) -#define MX27_INT_SDHC (NR_IRQS_LEGACY + 7) +#define MX27_INT_MSHC (NR_IRQS_LEGACY + 7) #define MX27_INT_GPIO (NR_IRQS_LEGACY + 8) #define MX27_INT_SDHC3 (NR_IRQS_LEGACY + 9) #define MX27_INT_SDHC2 (NR_IRQS_LEGACY + 10) -- cgit v1.2.3-70-g09d2 From 3b79cd15bfc5f1ddb5e387310fa3dbb09b81b552 Mon Sep 17 00:00:00 2001 From: Liu Ying Date: Wed, 3 Jul 2013 15:29:06 +0800 Subject: ARM: i.MX6Q: correct emi_sel clock muxing The correct muxing for emi_sel clock should be 2b'00 - 396M PFD 2b'01 - PLL3 2b'10 - AXI clk root 2b'11 - 352M PFD This patch corrects the muxing in the clock driver. Signed-off-by: Liu Ying Signed-off-by: Shawn Guo Acked-by: Dirk Behme --- arch/arm/mach-imx/clk-imx6q.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c index 4282e99f5ca..86567d980b0 100644 --- a/arch/arm/mach-imx/clk-imx6q.c +++ b/arch/arm/mach-imx/clk-imx6q.c @@ -199,7 +199,8 @@ static const char *pcie_axi_sels[] = { "axi", "ahb", }; static const char *ssi_sels[] = { "pll3_pfd2_508m", "pll3_pfd3_454m", "pll4_post_div", }; static const char *usdhc_sels[] = { "pll2_pfd2_396m", "pll2_pfd0_352m", }; static const char *enfc_sels[] = { "pll2_pfd0_352m", "pll2_bus", "pll3_usb_otg", "pll2_pfd2_396m", }; -static const char *emi_sels[] = { "axi", "pll3_usb_otg", "pll2_pfd2_396m", "pll2_pfd0_352m", }; +static const char *emi_sels[] = { "pll2_pfd2_396m", "pll3_usb_otg", "axi", "pll2_pfd0_352m", }; +static const char *emi_slow_sels[] = { "axi", "pll3_usb_otg", "pll2_pfd2_396m", "pll2_pfd0_352m", }; static const char *vdo_axi_sels[] = { "axi", "ahb", }; static const char *vpu_axi_sels[] = { "axi", "pll2_pfd2_396m", "pll2_pfd0_352m", }; static const char *cko1_sels[] = { "pll3_usb_otg", "pll2_bus", "pll1_sys", "pll5_video_div", @@ -392,7 +393,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node) clk[usdhc4_sel] = imx_clk_mux("usdhc4_sel", base + 0x1c, 19, 1, usdhc_sels, ARRAY_SIZE(usdhc_sels)); clk[enfc_sel] = imx_clk_mux("enfc_sel", base + 0x2c, 16, 2, enfc_sels, ARRAY_SIZE(enfc_sels)); clk[emi_sel] = imx_clk_mux("emi_sel", base + 0x1c, 27, 2, emi_sels, ARRAY_SIZE(emi_sels)); - clk[emi_slow_sel] = imx_clk_mux("emi_slow_sel", base + 0x1c, 29, 2, emi_sels, ARRAY_SIZE(emi_sels)); + clk[emi_slow_sel] = imx_clk_mux("emi_slow_sel", base + 0x1c, 29, 2, emi_slow_sels, ARRAY_SIZE(emi_slow_sels)); clk[vdo_axi_sel] = imx_clk_mux("vdo_axi_sel", base + 0x18, 11, 1, vdo_axi_sels, ARRAY_SIZE(vdo_axi_sels)); clk[vpu_axi_sel] = imx_clk_mux("vpu_axi_sel", base + 0x18, 14, 2, vpu_axi_sels, ARRAY_SIZE(vpu_axi_sels)); clk[cko1_sel] = imx_clk_mux("cko1_sel", base + 0x60, 0, 4, cko1_sels, ARRAY_SIZE(cko1_sels)); -- cgit v1.2.3-70-g09d2 From 66acaf3f897c9245f5456d884e5ae401700cbc45 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Mon, 1 Jul 2013 15:46:05 +0800 Subject: ARM: mxs: saif0 is the clock provider to sgtl5000 These systems all use saif0 as the mclock provider to codec sgtl5000. Reflect that in device tree source, so that sgtl5000 can find the clock by calling clk_get(). Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-apx4devkit.dts | 2 +- arch/arm/boot/dts/imx28-evk.dts | 2 +- arch/arm/boot/dts/imx28-m28evk.dts | 2 +- arch/arm/boot/dts/imx28.dtsi | 1 + 4 files changed, 4 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts index 43bf3c796cb..0e7fed47bd8 100644 --- a/arch/arm/boot/dts/imx28-apx4devkit.dts +++ b/arch/arm/boot/dts/imx28-apx4devkit.dts @@ -147,7 +147,7 @@ reg = <0x0a>; VDDA-supply = <®_3p3v>; VDDIO-supply = <®_3p3v>; - + clocks = <&saif0>; }; pcf8563: rtc@51 { diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index 1f0d38d7b16..e035f4664b9 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -195,7 +195,7 @@ reg = <0x0a>; VDDA-supply = <®_3p3v>; VDDIO-supply = <®_3p3v>; - + clocks = <&saif0>; }; at24@51 { diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts index 880df2f13be..44d9da57736 100644 --- a/arch/arm/boot/dts/imx28-m28evk.dts +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -184,7 +184,7 @@ reg = <0x0a>; VDDA-supply = <®_3p3v>; VDDIO-supply = <®_3p3v>; - + clocks = <&saif0>; }; eeprom: eeprom@51 { diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 6a8acb01b1d..9524a057128 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -837,6 +837,7 @@ compatible = "fsl,imx28-saif"; reg = <0x80042000 0x2000>; interrupts = <59 80>; + #clock-cells = <0>; clocks = <&clks 53>; dmas = <&dma_apbx 4>; dma-names = "rx-tx"; -- cgit v1.2.3-70-g09d2 From 4f71612ee3a1b2d15c8246d926a40c4f7d21cc3b Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Wed, 10 Jul 2013 14:05:44 +0800 Subject: ARM: imx: fix vf610 enet module clock selection The fec/enet driver calculates MDC rate with the formula below. ref_freq / ((MII_SPEED + 1) x 2) The ref_freq here is the fec internal module clock, which is missing from clk-vf610 clock driver right now. And clk-vf610 driver mistakenly supplies RMII clock (50 MHz) as the source to fec. This results in the situation that fec driver gets ref_freq as 50 MHz, while physically it runs at 66 MHz (fec module clock physically sources from ipg which runs at 66 MHz). That's why software expects MDC runs at 2.5 MHz, while the measurement tells it runs at 3.3 MHz. And this causes the PHY KSZ8041 keeps swithing between Full and Half mode as below. libphy: 400d0000.etherne:00 - Link is Up - 100/Full libphy: 400d0000.etherne:00 - Link is Up - 100/Half libphy: 400d0000.etherne:00 - Link is Up - 100/Full libphy: 400d0000.etherne:00 - Link is Up - 100/Half libphy: 400d0000.etherne:00 - Link is Up - 100/Full libphy: 400d0000.etherne:00 - Link is Up - 100/Half Add the missing module clock for ENET0 and ENET1, and correct the clock supplying in device tree to fix above issue. Thanks to Alison Wang for debugging the issue. Signed-off-by: Shawn Guo --- arch/arm/boot/dts/vf610.dtsi | 8 ++++---- arch/arm/mach-imx/clk-vf610.c | 2 ++ include/dt-bindings/clock/vf610-clock.h | 4 +++- 3 files changed, 9 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi index e1eb7dadda8..67d929cf980 100644 --- a/arch/arm/boot/dts/vf610.dtsi +++ b/arch/arm/boot/dts/vf610.dtsi @@ -442,8 +442,8 @@ compatible = "fsl,mvf600-fec"; reg = <0x400d0000 0x1000>; interrupts = <0 78 0x04>; - clocks = <&clks VF610_CLK_ENET>, - <&clks VF610_CLK_ENET>, + clocks = <&clks VF610_CLK_ENET0>, + <&clks VF610_CLK_ENET0>, <&clks VF610_CLK_ENET>; clock-names = "ipg", "ahb", "ptp"; status = "disabled"; @@ -453,8 +453,8 @@ compatible = "fsl,mvf600-fec"; reg = <0x400d1000 0x1000>; interrupts = <0 79 0x04>; - clocks = <&clks VF610_CLK_ENET>, - <&clks VF610_CLK_ENET>, + clocks = <&clks VF610_CLK_ENET1>, + <&clks VF610_CLK_ENET1>, <&clks VF610_CLK_ENET>; clock-names = "ipg", "ahb", "ptp"; status = "disabled"; diff --git a/arch/arm/mach-imx/clk-vf610.c b/arch/arm/mach-imx/clk-vf610.c index d617c0b7c80..b169a396d93 100644 --- a/arch/arm/mach-imx/clk-vf610.c +++ b/arch/arm/mach-imx/clk-vf610.c @@ -183,6 +183,8 @@ static void __init vf610_clocks_init(struct device_node *ccm_node) clk[VF610_CLK_ENET_TS_SEL] = imx_clk_mux("enet_ts_sel", CCM_CSCMR2, 0, 3, enet_ts_sels, 7); clk[VF610_CLK_ENET] = imx_clk_gate("enet", "enet_sel", CCM_CSCDR1, 24); clk[VF610_CLK_ENET_TS] = imx_clk_gate("enet_ts", "enet_ts_sel", CCM_CSCDR1, 23); + clk[VF610_CLK_ENET0] = imx_clk_gate2("enet0", "ipg_bus", CCM_CCGR9, CCM_CCGRx_CGn(0)); + clk[VF610_CLK_ENET1] = imx_clk_gate2("enet1", "ipg_bus", CCM_CCGR9, CCM_CCGRx_CGn(1)); clk[VF610_CLK_PIT] = imx_clk_gate2("pit", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(7)); diff --git a/include/dt-bindings/clock/vf610-clock.h b/include/dt-bindings/clock/vf610-clock.h index 15e997fa78f..4aa2b48cd15 100644 --- a/include/dt-bindings/clock/vf610-clock.h +++ b/include/dt-bindings/clock/vf610-clock.h @@ -158,6 +158,8 @@ #define VF610_CLK_GPU_SEL 145 #define VF610_CLK_GPU_EN 146 #define VF610_CLK_GPU2D 147 -#define VF610_CLK_END 148 +#define VF610_CLK_ENET0 148 +#define VF610_CLK_ENET1 149 +#define VF610_CLK_END 150 #endif /* __DT_BINDINGS_CLOCK_VF610_H */ -- cgit v1.2.3-70-g09d2 From 15968f1bd4341cfa54023348a4e0b94798211742 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Thu, 11 Jul 2013 16:37:47 +0200 Subject: ARM i.MX53: mba53: Fix PWM backlight DT node The i.MX53 PWM controller uses two cells to describe the PWM specifier. Remove the extra unused values from the backlight DT node pwms property. Signed-off-by: Laurent Pinchart Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx53-mba53.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/imx53-mba53.dts index aaa33bc99f7..a6309026794 100644 --- a/arch/arm/boot/dts/imx53-mba53.dts +++ b/arch/arm/boot/dts/imx53-mba53.dts @@ -27,7 +27,7 @@ backlight { compatible = "pwm-backlight"; - pwms = <&pwm2 0 50000 0 0>; + pwms = <&pwm2 0 50000>; brightness-levels = <0 24 28 32 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100>; default-brightness-level = <10>; enable-gpios = <&gpio7 7 0>; -- cgit v1.2.3-70-g09d2 From ae7cc03e435fe86d95a3fbef52161dbd9f97db77 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 15 Jul 2013 00:39:41 -0700 Subject: ARM: multi_v7: Enabled omap4430 sdp nfsroot By adding support for OCP2SCP, SPI and KS8851 I can also boot test multi_v7_defconfig easily. Note that if using an older u-boot, CONFIG_ARM_ATAG_DTB_COMPAT=y may also be needed for the appended DTB based booting. Reviewed-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/configs/multi_v7_defconfig | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index fe0bdc361d2..120b08edb9a 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -53,6 +53,7 @@ CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_DEVTMPFS=y CONFIG_DEVTMPFS_MOUNT=y +CONFIG_OMAP_OCP2SCP=y CONFIG_BLK_DEV_SD=y CONFIG_ATA=y CONFIG_SATA_AHCI_PLATFORM=y @@ -61,6 +62,7 @@ CONFIG_SATA_MV=y CONFIG_NETDEVICES=y CONFIG_SUN4I_EMAC=y CONFIG_NET_CALXEDA_XGMAC=y +CONFIG_KS8851=y CONFIG_SMSC911X=y CONFIG_STMMAC_ETH=y CONFIG_MDIO_SUN4I=y @@ -89,6 +91,7 @@ CONFIG_I2C_DESIGNWARE_PLATFORM=y CONFIG_I2C_SIRF=y CONFIG_I2C_TEGRA=y CONFIG_SPI=y +CONFIG_SPI_OMAP24XX=y CONFIG_SPI_PL022=y CONFIG_SPI_SIRF=y CONFIG_SPI_TEGRA114=y -- cgit v1.2.3-70-g09d2 From 13782a7e2821f62efc747fd26605de4dc823ee29 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 7 Jun 2013 15:01:58 -0700 Subject: ARM: dts: Add missing vmmc2 regulator for twl For some reason vmmc2 regulator is missing for twl. Let's add it. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/twl4030.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi index b3034da00a3..ae6a17aed9e 100644 --- a/arch/arm/boot/dts/twl4030.dtsi +++ b/arch/arm/boot/dts/twl4030.dtsi @@ -47,6 +47,12 @@ regulator-max-microvolt = <3150000>; }; + vmmc2: regulator-vmmc2 { + compatible = "ti,twl4030-vmmc2"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; + }; + vusb1v5: regulator-vusb1v5 { compatible = "ti,twl4030-vusb1v5"; }; -- cgit v1.2.3-70-g09d2 From 84bb08472520882394fe16d7a3548793302563de Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Sun, 9 Jun 2013 22:07:47 -0300 Subject: ARM: dts: imx51-babbage: Pass a real clock to the codec On imx51_babbage the codec clock is activated via GPIO4_26. Provide a real clock to the sgtl5000 codec via device tree. Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx51-babbage.dts | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts index 6dd9486c755..ad3471ca17c 100644 --- a/arch/arm/boot/dts/imx51-babbage.dts +++ b/arch/arm/boot/dts/imx51-babbage.dts @@ -61,6 +61,16 @@ mux-int-port = <2>; mux-ext-port = <3>; }; + + clocks { + clk_26M: codec_clock { + compatible = "fixed-clock"; + reg=<0>; + #clock-cells = <0>; + clock-frequency = <26000000>; + gpios = <&gpio4 26 1>; + }; + }; }; &esdhc1 { @@ -229,6 +239,7 @@ MX51_PAD_EIM_A27__GPIO2_21 0x5 MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 MX51_PAD_CSPI1_SS1__GPIO4_25 0x85 + MX51_PAD_CSPI1_RDY__GPIO4_26 0x80000000 >; }; }; @@ -255,7 +266,7 @@ sgtl5000: codec@0a { compatible = "fsl,sgtl5000"; reg = <0x0a>; - clock-frequency = <26000000>; + clocks = <&clk_26M>; VDDA-supply = <&vdig_reg>; VDDIO-supply = <&vvideo_reg>; }; -- cgit v1.2.3-70-g09d2 From e085cad6c653e20e213a662ef32fb6191ae0197d Mon Sep 17 00:00:00 2001 From: Kukjin Kim Date: Wed, 26 Jun 2013 22:29:44 +0900 Subject: ARM: EXYNOS: skip pm support on exynos5440 EXYNOS5440 doesn't support PM and current single image for EXYNOS will be break without this patch. Actually, SSDK5440 cannot boot without this so this should be merged during rc. Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/pm.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c index 41c20692a13..c679db57726 100644 --- a/arch/arm/mach-exynos/pm.c +++ b/arch/arm/mach-exynos/pm.c @@ -217,6 +217,9 @@ static __init int exynos_pm_drvinit(void) struct clk *pll_base; unsigned int tmp; + if (soc_is_exynos5440()) + return 0; + s3c_pm_init(); /* All wakeup disable */ @@ -340,6 +343,9 @@ static struct syscore_ops exynos_pm_syscore_ops = { static __init int exynos_pm_syscore_init(void) { + if (soc_is_exynos5440()) + return 0; + register_syscore_ops(&exynos_pm_syscore_ops); return 0; } -- cgit v1.2.3-70-g09d2 From ea2761763739619ca49602d891ec3ffb33ffc71b Mon Sep 17 00:00:00 2001 From: Subash Patel Date: Tue, 16 Jul 2013 12:42:13 +0900 Subject: ARM: EXYNOS: change the PHYSMEM_BITS and SECTION_SIZE On EXYNOS5440 there is DRAM on the 36-bit address range. Hence this patch converts the MAX_PHYSMEM_BITS macro to 36 if LPAE is enabled for the ARM architecture. The conventional section size on EXYNOS is 256M due to sparsemem. Since EXYNOS5440 has memory in multiples of 1G in 32-bit and 36-bit range, this has now been modified to 31. Signed-off-by: Subash Patel Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/include/mach/memory.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-exynos/include/mach/memory.h b/arch/arm/mach-exynos/include/mach/memory.h index 374ef2cf715..2a4cdb7cb32 100644 --- a/arch/arm/mach-exynos/include/mach/memory.h +++ b/arch/arm/mach-exynos/include/mach/memory.h @@ -15,8 +15,13 @@ #define PLAT_PHYS_OFFSET UL(0x40000000) +#ifndef CONFIG_ARM_LPAE /* Maximum of 256MiB in one bank */ #define MAX_PHYSMEM_BITS 32 #define SECTION_SIZE_BITS 28 +#else +#define MAX_PHYSMEM_BITS 36 +#define SECTION_SIZE_BITS 31 +#endif #endif /* __ASM_ARCH_MEMORY_H */ -- cgit v1.2.3-70-g09d2 From cfaf8ee2f91607c8955af68538ba849b125fb8d5 Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Tue, 16 Jul 2013 12:42:59 +0900 Subject: ARM: EXYNOS: Enable 64-bit DMA for EXYNOS5440 if LPAE is enabled Allow 64-bit DMA addresses if LPAE is enabled on EXYNOS5440. Signed-off-by: Thomas Abraham Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 855d4a7b462..5952e68c76c 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -92,6 +92,7 @@ config SOC_EXYNOS5440 bool "SAMSUNG EXYNOS5440" default y depends on ARCH_EXYNOS5 + select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE select ARCH_HAS_OPP select HAVE_ARM_ARCH_TIMER select AUTO_ZRELADDR -- cgit v1.2.3-70-g09d2 From 64597f9dae1850e0360ae2e9b5485d4b5d1fdf4c Mon Sep 17 00:00:00 2001 From: Michael Mueller Date: Tue, 2 Jul 2013 22:58:26 +0200 Subject: s390/ptrace: PTRACE_TE_ABORT_RAND The patch implements a s390 specific ptrace request PTRACE_TE_ABORT_RAND to modify the randomness of spontaneous aborts of memory transactions of the transaction execution facility. The data argument of the ptrace request is used to specify the levels of randomness, 0 for normal operation, 1 to abort every transaction at a random instruction, and 2 to abort a random transaction at a random instruction. The default is 0 for normal operation. Acked-by: Heiko Carstens Signed-off-by: Michael Mueller Signed-off-by: Martin Schwidefsky --- arch/s390/include/asm/processor.h | 10 +++++++- arch/s390/include/asm/switch_to.h | 4 +-- arch/s390/include/uapi/asm/ptrace.h | 1 + arch/s390/kernel/ptrace.c | 50 +++++++++++++++++++++++++++++-------- 4 files changed, 51 insertions(+), 14 deletions(-) (limited to 'arch') diff --git a/arch/s390/include/asm/processor.h b/arch/s390/include/asm/processor.h index 6b499870662..b0e6435b2f0 100644 --- a/arch/s390/include/asm/processor.h +++ b/arch/s390/include/asm/processor.h @@ -91,7 +91,15 @@ struct thread_struct { #endif }; -#define PER_FLAG_NO_TE 1UL /* Flag to disable transactions. */ +/* Flag to disable transactions. */ +#define PER_FLAG_NO_TE 1UL +/* Flag to enable random transaction aborts. */ +#define PER_FLAG_TE_ABORT_RAND 2UL +/* Flag to specify random transaction abort mode: + * - abort each transaction at a random instruction before TEND if set. + * - abort random transactions at a random instruction if cleared. + */ +#define PER_FLAG_TE_ABORT_RAND_TEND 4UL typedef struct thread_struct thread_struct; diff --git a/arch/s390/include/asm/switch_to.h b/arch/s390/include/asm/switch_to.h index f3a9e0f9270..80b6f11263c 100644 --- a/arch/s390/include/asm/switch_to.h +++ b/arch/s390/include/asm/switch_to.h @@ -10,7 +10,7 @@ #include extern struct task_struct *__switch_to(void *, void *); -extern void update_per_regs(struct task_struct *task); +extern void update_cr_regs(struct task_struct *task); static inline void save_fp_regs(s390_fp_regs *fpregs) { @@ -86,7 +86,7 @@ static inline void restore_access_regs(unsigned int *acrs) restore_fp_regs(&next->thread.fp_regs); \ restore_access_regs(&next->thread.acrs[0]); \ restore_ri_cb(next->thread.ri_cb, prev->thread.ri_cb); \ - update_per_regs(next); \ + update_cr_regs(next); \ } \ prev = __switch_to(prev,next); \ } while (0) diff --git a/arch/s390/include/uapi/asm/ptrace.h b/arch/s390/include/uapi/asm/ptrace.h index 3aa9f1ec5b2..7a84619e315 100644 --- a/arch/s390/include/uapi/asm/ptrace.h +++ b/arch/s390/include/uapi/asm/ptrace.h @@ -400,6 +400,7 @@ typedef struct #define PTRACE_POKE_SYSTEM_CALL 0x5008 #define PTRACE_ENABLE_TE 0x5009 #define PTRACE_DISABLE_TE 0x5010 +#define PTRACE_TE_ABORT_RAND 0x5011 /* * PT_PROT definition is loosely based on hppa bsd definition in diff --git a/arch/s390/kernel/ptrace.c b/arch/s390/kernel/ptrace.c index a314c57f4e9..e9fadb04e3c 100644 --- a/arch/s390/kernel/ptrace.c +++ b/arch/s390/kernel/ptrace.c @@ -47,7 +47,7 @@ enum s390_regset { REGSET_GENERAL_EXTENDED, }; -void update_per_regs(struct task_struct *task) +void update_cr_regs(struct task_struct *task) { struct pt_regs *regs = task_pt_regs(task); struct thread_struct *thread = &task->thread; @@ -56,17 +56,25 @@ void update_per_regs(struct task_struct *task) #ifdef CONFIG_64BIT /* Take care of the enable/disable of transactional execution. */ if (MACHINE_HAS_TE) { - unsigned long cr0, cr0_new; + unsigned long cr[3], cr_new[3]; - __ctl_store(cr0, 0, 0); - /* set or clear transaction execution bits 8 and 9. */ + __ctl_store(cr, 0, 2); + cr_new[1] = cr[1]; + /* Set or clear transaction execution TXC/PIFO bits 8 and 9. */ if (task->thread.per_flags & PER_FLAG_NO_TE) - cr0_new = cr0 & ~(3UL << 54); + cr_new[0] = cr[0] & ~(3UL << 54); else - cr0_new = cr0 | (3UL << 54); - /* Only load control register 0 if necessary. */ - if (cr0 != cr0_new) - __ctl_load(cr0_new, 0, 0); + cr_new[0] = cr[0] | (3UL << 54); + /* Set or clear transaction execution TDC bits 62 and 63. */ + cr_new[2] = cr[2] & ~3UL; + if (task->thread.per_flags & PER_FLAG_TE_ABORT_RAND) { + if (task->thread.per_flags & PER_FLAG_TE_ABORT_RAND_TEND) + cr_new[2] |= 1UL; + else + cr_new[2] |= 2UL; + } + if (memcmp(&cr_new, &cr, sizeof(cr))) + __ctl_load(cr_new, 0, 2); } #endif /* Copy user specified PER registers */ @@ -100,14 +108,14 @@ void user_enable_single_step(struct task_struct *task) { set_tsk_thread_flag(task, TIF_SINGLE_STEP); if (task == current) - update_per_regs(task); + update_cr_regs(task); } void user_disable_single_step(struct task_struct *task) { clear_tsk_thread_flag(task, TIF_SINGLE_STEP); if (task == current) - update_per_regs(task); + update_cr_regs(task); } /* @@ -447,6 +455,26 @@ long arch_ptrace(struct task_struct *child, long request, if (!MACHINE_HAS_TE) return -EIO; child->thread.per_flags |= PER_FLAG_NO_TE; + child->thread.per_flags &= ~PER_FLAG_TE_ABORT_RAND; + return 0; + case PTRACE_TE_ABORT_RAND: + if (!MACHINE_HAS_TE || (child->thread.per_flags & PER_FLAG_NO_TE)) + return -EIO; + switch (data) { + case 0UL: + child->thread.per_flags &= ~PER_FLAG_TE_ABORT_RAND; + break; + case 1UL: + child->thread.per_flags |= PER_FLAG_TE_ABORT_RAND; + child->thread.per_flags |= PER_FLAG_TE_ABORT_RAND_TEND; + break; + case 2UL: + child->thread.per_flags |= PER_FLAG_TE_ABORT_RAND; + child->thread.per_flags &= ~PER_FLAG_TE_ABORT_RAND_TEND; + break; + default: + return -EINVAL; + } return 0; default: /* Removing high order bit from addr (only for 31 bit). */ -- cgit v1.2.3-70-g09d2 From 741532c4a995be11815cb72d4d7a48f442a22fea Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 18 Jun 2013 19:04:47 +0300 Subject: ARM: OMAP2+: Provide alias to USB PHY clock Till the OMAP clocks are correctly defined in device tree, use this temporary hack to provide clock alias to the USB PHY clocks. Without this, USB Host & Ethernet will not be functional with device tree boots on Panda and uEVM. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-generic.c | 23 ++++++++++++++++++++++- 1 file changed, 22 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index e5fbfed69aa..be5d005ebad 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -15,6 +15,7 @@ #include #include #include +#include #include @@ -35,6 +36,21 @@ static struct of_device_id omap_dt_match_table[] __initdata = { { } }; +/* + * Create alias for USB host PHY clock. + * Remove this when clock phandle can be provided via DT + */ +static void __init legacy_init_ehci_clk(char *clkname) +{ + int ret; + + ret = clk_add_alias("main_clk", NULL, clkname, NULL); + if (ret) { + pr_err("%s:Failed to add main_clk alias to %s :%d\n", + __func__, clkname, ret); + } +} + static void __init omap_generic_init(void) { omap_sdrc_init(NULL, NULL); @@ -45,10 +61,15 @@ static void __init omap_generic_init(void) * HACK: call display setup code for selected boards to enable omapdss. * This will be removed when omapdss supports DT. */ - if (of_machine_is_compatible("ti,omap4-panda")) + if (of_machine_is_compatible("ti,omap4-panda")) { omap4_panda_display_init_of(); + legacy_init_ehci_clk("auxclk3_ck"); + + } else if (of_machine_is_compatible("ti,omap4-sdp")) omap_4430sdp_display_init_of(); + else if (of_machine_is_compatible("ti,omap5-uevm")) + legacy_init_ehci_clk("auxclk1_ck"); } #ifdef CONFIG_SOC_OMAP2420 -- cgit v1.2.3-70-g09d2 From 30f099cd88c8e92206c5e4ccf814ce0362db3d22 Mon Sep 17 00:00:00 2001 From: Wei Yongjun Date: Wed, 26 Jun 2013 09:58:16 +0800 Subject: ARM: edma: remove duplicated include from edma.c Remove duplicated include. Signed-off-by: Wei Yongjun Signed-off-by: Sekhar Nori --- arch/arm/common/edma.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c index a432e6c1dac..39ad030ac0c 100644 --- a/arch/arm/common/edma.c +++ b/arch/arm/common/edma.c @@ -26,7 +26,6 @@ #include #include #include -#include #include #include #include -- cgit v1.2.3-70-g09d2 From 9c559708b6cda71d8fdabc3f98cb7e98edbd4f0b Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Fri, 12 Jul 2013 15:19:03 +0530 Subject: ARM: davinci: make file local variables static Make file local variables static in mach-davinci. This fixes sparse warnings of the form: arch/arm/mach-davinci/dm355.c:863:27: warning: symbol 'dm355_venc_pdata' was not declared. Should it be static? Cc: Prabhakar Lad Acked-by: Prabhakar Lad Signed-off-by: Sekhar Nori --- arch/arm/mach-davinci/board-dm365-evm.c | 2 +- arch/arm/mach-davinci/dm355.c | 2 +- arch/arm/mach-davinci/dm365.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index afbc439f11d..4cdb61c5445 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -505,7 +505,7 @@ static struct vpbe_output dm365evm_vpbe_outputs[] = { /* * Amplifiers on the board */ -struct ths7303_platform_data ths7303_pdata = { +static struct ths7303_platform_data ths7303_pdata = { .ch_1 = 3, .ch_2 = 3, .ch_3 = 3, diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c index 42ef53f62c6..86100d17969 100644 --- a/arch/arm/mach-davinci/dm355.c +++ b/arch/arm/mach-davinci/dm355.c @@ -860,7 +860,7 @@ static struct platform_device dm355_vpbe_display = { }, }; -struct venc_platform_data dm355_venc_pdata = { +static struct venc_platform_data dm355_venc_pdata = { .setup_pinmux = dm355_vpbe_setup_pinmux, .setup_clock = dm355_venc_setup_clock, }; diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c index fa7af5eda52..dad28029ba9 100644 --- a/arch/arm/mach-davinci/dm365.c +++ b/arch/arm/mach-davinci/dm365.c @@ -1349,7 +1349,7 @@ static struct platform_device dm365_vpbe_display = { }, }; -struct venc_platform_data dm365_venc_pdata = { +static struct venc_platform_data dm365_venc_pdata = { .setup_pinmux = dm365_vpbe_setup_pinmux, .setup_clock = dm365_venc_setup_clock, }; -- cgit v1.2.3-70-g09d2 From cf690331642010a837c026088588761f61528ddf Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Fri, 12 Jul 2013 19:19:59 +0530 Subject: ARM: davinci: defconfig: enable EDMA driver Enable EDMA dmaengine driver by default in DaVinci defconfig files as it is required for DMA support on MMC/SD, SPI etc. Signed-off-by: Sekhar Nori --- arch/arm/configs/da8xx_omapl_defconfig | 2 ++ arch/arm/configs/davinci_all_defconfig | 2 ++ 2 files changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/arm/configs/da8xx_omapl_defconfig b/arch/arm/configs/da8xx_omapl_defconfig index 7c868139bdb..1571bea48be 100644 --- a/arch/arm/configs/da8xx_omapl_defconfig +++ b/arch/arm/configs/da8xx_omapl_defconfig @@ -102,6 +102,8 @@ CONFIG_SND_SOC=m CONFIG_SND_DAVINCI_SOC=m # CONFIG_HID_SUPPORT is not set # CONFIG_USB_SUPPORT is not set +CONFIG_DMADEVICES=y +CONFIG_TI_EDMA=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y CONFIG_XFS_FS=m diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig index c86fd75e181..ab2f7378352 100644 --- a/arch/arm/configs/davinci_all_defconfig +++ b/arch/arm/configs/davinci_all_defconfig @@ -162,6 +162,8 @@ CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=m CONFIG_LEDS_TRIGGER_HEARTBEAT=m CONFIG_RTC_CLASS=y +CONFIG_DMADEVICES=y +CONFIG_TI_EDMA=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y CONFIG_XFS_FS=m -- cgit v1.2.3-70-g09d2 From 3715534adf899bfc842868865f13a001b8aa4692 Mon Sep 17 00:00:00 2001 From: Paul Bolle Date: Sun, 14 Jul 2013 14:02:19 +0200 Subject: cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig Kconfig symbol S3C24XX_PLL depends on ARM_S3C24XX. But that symbol doesn't exist. Commit f023f8dd59bf ("cpufreq: s3c24xx: move cpufreq driver to drivers/cpufreq"), which added this issue, makes it clear that ARM_S3C24XX_CPUFREQ was intended here. Signed-off-by: Paul Bolle Acked-by: Viresh Kumar Signed-off-by: Rafael J. Wysocki --- arch/arm/mach-s3c24xx/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c24xx/Kconfig b/arch/arm/mach-s3c24xx/Kconfig index 6d9252e081c..7791ac76f94 100644 --- a/arch/arm/mach-s3c24xx/Kconfig +++ b/arch/arm/mach-s3c24xx/Kconfig @@ -208,7 +208,7 @@ config S3C24XX_GPIO_EXTRA128 config S3C24XX_PLL bool "Support CPUfreq changing of PLL frequency (EXPERIMENTAL)" - depends on ARM_S3C24XX + depends on ARM_S3C24XX_CPUFREQ help Compile in support for changing the PLL frequency from the S3C24XX series CPUfreq driver. The PLL takes time to settle -- cgit v1.2.3-70-g09d2 From a47bde9b7cbeb87dbb1c5554e90b770d3cc06c5c Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Wed, 17 Jul 2013 17:28:48 +0200 Subject: MIPS: Delete dead invocation of exception_exit(). panic() doesn't return so this call was useless. Signed-off-by: Ralf Baechle Reported-by: Alexander Sverdlin --- arch/mips/kernel/traps.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/kernel/traps.c b/arch/mips/kernel/traps.c index 0903d70b2cf..3035a40c455 100644 --- a/arch/mips/kernel/traps.c +++ b/arch/mips/kernel/traps.c @@ -1242,7 +1242,6 @@ asmlinkage void do_mcheck(struct pt_regs *regs) panic("Caught Machine Check exception - %scaused by multiple " "matching entries in the TLB.", (multi_match) ? "" : "not "); - exception_exit(prev_state); } asmlinkage void do_mt(struct pt_regs *regs) -- cgit v1.2.3-70-g09d2 From 1c118b8226922d225a7df4127926ed2a2d73baaf Mon Sep 17 00:00:00 2001 From: Xiao Guangrong Date: Thu, 18 Jul 2013 12:52:37 +0800 Subject: KVM: MMU: avoid fast page fault fixing mmio page fault Currently, fast page fault incorrectly tries to fix mmio page fault when the generation number is invalid (spte.gen != kvm.gen). It then returns to guest to retry the fault since it sees the last spte is nonpresent. This causes an infinite loop. Since fast page fault only works for direct mmu, the issue exists when 1) tdp is enabled. It is only triggered only on AMD host since on Intel host the mmio page fault is recognized as ept-misconfig whose handler call fault-page path with error_code = 0 2) guest paging is disabled. Under this case, the issue is hardly discovered since paging disable is short-lived and the sptes will be invalid after memslot changed for 150 times Fix it by filtering out MMIO page faults in page_fault_can_be_fast. Reported-by: Markus Trippelsdorf Tested-by: Markus Trippelsdorf Signed-off-by: Xiao Guangrong Signed-off-by: Paolo Bonzini --- arch/x86/kvm/mmu.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch') diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c index 0d094da4954..9e9285ae9b9 100644 --- a/arch/x86/kvm/mmu.c +++ b/arch/x86/kvm/mmu.c @@ -2810,6 +2810,13 @@ exit: static bool page_fault_can_be_fast(struct kvm_vcpu *vcpu, u32 error_code) { + /* + * Do not fix the mmio spte with invalid generation number which + * need to be updated by slow page fault path. + */ + if (unlikely(error_code & PFERR_RSVD_MASK)) + return false; + /* * #PF can be fast only if the shadow page table is present and it * is caused by write-protect, that means we just need change the -- cgit v1.2.3-70-g09d2 From 1eeb74782d354175ef9f3bff02fae62c6e0aef24 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Tue, 16 Jul 2013 10:24:48 +0200 Subject: s390/bpf,jit: call module_free() from any context The workqueue workaround is no longer needed. Same as 5199dfe531 "sparc: bpf_jit_comp: can call module_free() from any context". Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/net/bpf_jit_comp.c | 20 +++----------------- 1 file changed, 3 insertions(+), 17 deletions(-) (limited to 'arch') diff --git a/arch/s390/net/bpf_jit_comp.c b/arch/s390/net/bpf_jit_comp.c index 82f165f8078..a41f0b15faa 100644 --- a/arch/s390/net/bpf_jit_comp.c +++ b/arch/s390/net/bpf_jit_comp.c @@ -772,8 +772,7 @@ void bpf_jit_compile(struct sk_filter *fp) } else if (jit.prg == cjit.prg && jit.lit == cjit.lit) { prg_len = jit.prg - jit.start; lit_len = jit.lit - jit.mid; - size = max_t(unsigned long, prg_len + lit_len, - sizeof(struct work_struct)); + size = prg_len + lit_len; if (size >= BPF_SIZE_MAX) goto out; jit.start = module_alloc(size); @@ -804,21 +803,8 @@ out: kfree(addrs); } -static void jit_free_defer(struct work_struct *arg) -{ - module_free(NULL, arg); -} - -/* run from softirq, we must use a work_struct to call - * module_free() from process context - */ void bpf_jit_free(struct sk_filter *fp) { - struct work_struct *work; - - if (fp->bpf_func == sk_run_filter) - return; - work = (struct work_struct *)fp->bpf_func; - INIT_WORK(work, jit_free_defer); - schedule_work(work); + if (fp->bpf_func != sk_run_filter) + module_free(NULL, fp->bpf_func); } -- cgit v1.2.3-70-g09d2 From fee1b5488d76396d8f95989624d37f436b3fba44 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Tue, 16 Jul 2013 10:36:06 +0200 Subject: s390/bpf,jit: use generic jit dumper This is the s390 backend of 79617801 "filter: bpf_jit_comp: refactor and unify BPF JIT image dump output". Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/net/bpf_jit_comp.c | 10 ++-------- 1 file changed, 2 insertions(+), 8 deletions(-) (limited to 'arch') diff --git a/arch/s390/net/bpf_jit_comp.c b/arch/s390/net/bpf_jit_comp.c index a41f0b15faa..80828bfee2e 100644 --- a/arch/s390/net/bpf_jit_comp.c +++ b/arch/s390/net/bpf_jit_comp.c @@ -787,15 +787,9 @@ void bpf_jit_compile(struct sk_filter *fp) cjit = jit; } if (bpf_jit_enable > 1) { - pr_err("flen=%d proglen=%lu pass=%d image=%p\n", - fp->len, jit.end - jit.start, pass, jit.start); - if (jit.start) { - printk(KERN_ERR "JIT code:\n"); + bpf_jit_dump(fp->len, jit.end - jit.start, pass, jit.start); + if (jit.start) print_fn_code(jit.start, jit.mid - jit.start); - print_hex_dump(KERN_ERR, "JIT literals:\n", - DUMP_PREFIX_ADDRESS, 16, 1, - jit.mid, jit.end - jit.mid, false); - } } if (jit.start) fp->bpf_func = (void *) jit.start; -- cgit v1.2.3-70-g09d2 From aa2d2c73c21f22ce4c643128b671aa7e7bbff54f Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Tue, 16 Jul 2013 13:25:49 +0200 Subject: s390/bpf,jit: address randomize and write protect jit code This is the s390 variant of 314beb9b "x86: bpf_jit_comp: secure bpf jit against spraying attacks". With this change the whole jit code and literal pool will be write protected after creation. In addition the start address of the jit code won't be always on a page boundary anymore. Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/net/bpf_jit_comp.c | 51 +++++++++++++++++++++++++++++++++++++++----- 1 file changed, 46 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/s390/net/bpf_jit_comp.c b/arch/s390/net/bpf_jit_comp.c index 80828bfee2e..788e22395ac 100644 --- a/arch/s390/net/bpf_jit_comp.c +++ b/arch/s390/net/bpf_jit_comp.c @@ -9,6 +9,7 @@ #include #include #include +#include #include #include #include @@ -738,8 +739,41 @@ out: return -1; } +/* + * Note: for security reasons, bpf code will follow a randomly + * sized amount of illegal instructions. + */ +struct bpf_binary_header { + unsigned int pages; + u8 image[]; +}; + +static struct bpf_binary_header *bpf_alloc_binary(unsigned int bpfsize, + u8 **image_ptr) +{ + struct bpf_binary_header *header; + unsigned int sz, hole; + + /* Most BPF filters are really small, but if some of them fill a page, + * allow at least 128 extra bytes for illegal instructions. + */ + sz = round_up(bpfsize + sizeof(*header) + 128, PAGE_SIZE); + header = module_alloc(sz); + if (!header) + return NULL; + memset(header, 0, sz); + header->pages = sz / PAGE_SIZE; + hole = sz - bpfsize + sizeof(*header); + /* Insert random number of illegal instructions before BPF code + * and make sure the first instruction starts at an even address. + */ + *image_ptr = &header->image[(prandom_u32() % hole) & -2]; + return header; +} + void bpf_jit_compile(struct sk_filter *fp) { + struct bpf_binary_header *header = NULL; unsigned long size, prg_len, lit_len; struct bpf_jit jit, cjit; unsigned int *addrs; @@ -775,8 +809,8 @@ void bpf_jit_compile(struct sk_filter *fp) size = prg_len + lit_len; if (size >= BPF_SIZE_MAX) goto out; - jit.start = module_alloc(size); - if (!jit.start) + header = bpf_alloc_binary(size, &jit.start); + if (!header) goto out; jit.prg = jit.mid = jit.start + prg_len; jit.lit = jit.end = jit.start + prg_len + lit_len; @@ -791,14 +825,21 @@ void bpf_jit_compile(struct sk_filter *fp) if (jit.start) print_fn_code(jit.start, jit.mid - jit.start); } - if (jit.start) + if (jit.start) { + set_memory_ro((unsigned long)header, header->pages); fp->bpf_func = (void *) jit.start; + } out: kfree(addrs); } void bpf_jit_free(struct sk_filter *fp) { - if (fp->bpf_func != sk_run_filter) - module_free(NULL, fp->bpf_func); + unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK; + struct bpf_binary_header *header = (void *)addr; + + if (fp->bpf_func == sk_run_filter) + return; + set_memory_rw(addr, header->pages); + module_free(NULL, header); } -- cgit v1.2.3-70-g09d2 From c9a7afa380ecaeb0fbeec2e82f86ec5548ad2963 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Wed, 17 Jul 2013 14:26:50 +0200 Subject: s390/bpf,jit: add pkt_type support s390 version of 3b58908a "x86: bpf_jit_comp: add pkt_type support". Signed-off-by: Heiko Carstens --- arch/s390/net/bpf_jit_comp.c | 42 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) (limited to 'arch') diff --git a/arch/s390/net/bpf_jit_comp.c b/arch/s390/net/bpf_jit_comp.c index 788e22395ac..d5f10a43a58 100644 --- a/arch/s390/net/bpf_jit_comp.c +++ b/arch/s390/net/bpf_jit_comp.c @@ -10,6 +10,7 @@ #include #include #include +#include #include #include #include @@ -222,6 +223,37 @@ static void bpf_jit_epilogue(struct bpf_jit *jit) EMIT2(0x07fe); } +/* Helper to find the offset of pkt_type in sk_buff + * Make sure its still a 3bit field starting at the MSBs within a byte. + */ +#define PKT_TYPE_MAX 0xe0 +static int pkt_type_offset; + +static int __init bpf_pkt_type_offset_init(void) +{ + struct sk_buff skb_probe = { + .pkt_type = ~0, + }; + char *ct = (char *)&skb_probe; + int off; + + pkt_type_offset = -1; + for (off = 0; off < sizeof(struct sk_buff); off++) { + if (!ct[off]) + continue; + if (ct[off] == PKT_TYPE_MAX) + pkt_type_offset = off; + else { + /* Found non matching bit pattern, fix needed. */ + WARN_ON_ONCE(1); + pkt_type_offset = -1; + return -1; + } + } + return 0; +} +device_initcall(bpf_pkt_type_offset_init); + /* * make sure we dont leak kernel information to user */ @@ -721,6 +753,16 @@ call_fn: /* lg %r1,(%r13) */ EMIT4_DISP(0x88500000, 12); } break; + case BPF_S_ANC_PKTTYPE: + if (pkt_type_offset < 0) + goto out; + /* lhi %r5,0 */ + EMIT4(0xa7580000); + /* ic %r5,(%r2) */ + EMIT4_DISP(0x43502000, pkt_type_offset); + /* srl %r5,5 */ + EMIT4_DISP(0x88500000, 5); + break; case BPF_S_ANC_CPU: /* A = smp_processor_id() */ #ifdef CONFIG_SMP /* l %r5, */ -- cgit v1.2.3-70-g09d2 From 191a2fa0a8d2bbb64c98f9b1976fcb37ee5eae6b Mon Sep 17 00:00:00 2001 From: Michael Holzheu Date: Thu, 18 Jul 2013 12:18:27 +0200 Subject: s390/kdump: Allow copy_oldmem_page() copy to virtual memory The kdump mmap patch series (git commit 83086978c63afd7c73e1c) changed the requirements for copy_oldmem_page(). Now this function is used for copying to virtual memory. So implement vmalloc support for the s390 version of copy_oldmem_page(). Signed-off-by: Michael Holzheu Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/crash_dump.c | 51 +++++++++++++++++++++++++++++++++++++++---- 1 file changed, 47 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/s390/kernel/crash_dump.c b/arch/s390/kernel/crash_dump.c index f703d91bf72..d8f35565717 100644 --- a/arch/s390/kernel/crash_dump.c +++ b/arch/s390/kernel/crash_dump.c @@ -21,6 +21,48 @@ #define PTR_SUB(x, y) (((char *) (x)) - ((unsigned long) (y))) #define PTR_DIFF(x, y) ((unsigned long)(((char *) (x)) - ((unsigned long) (y)))) + +/* + * Return physical address for virtual address + */ +static inline void *load_real_addr(void *addr) +{ + unsigned long real_addr; + + asm volatile( + " lra %0,0(%1)\n" + " jz 0f\n" + " la %0,0\n" + "0:" + : "=a" (real_addr) : "a" (addr) : "cc"); + return (void *)real_addr; +} + +/* + * Copy up to one page to vmalloc or real memory + */ +static ssize_t copy_page_real(void *buf, void *src, size_t csize) +{ + size_t size; + + if (is_vmalloc_addr(buf)) { + BUG_ON(csize >= PAGE_SIZE); + /* If buf is not page aligned, copy first part */ + size = min(roundup(__pa(buf), PAGE_SIZE) - __pa(buf), csize); + if (size) { + if (memcpy_real(load_real_addr(buf), src, size)) + return -EFAULT; + buf += size; + src += size; + } + /* Copy second part */ + size = csize - size; + return (size) ? memcpy_real(load_real_addr(buf), src, size) : 0; + } else { + return memcpy_real(buf, src, csize); + } +} + /* * Copy one page from "oldmem" * @@ -32,6 +74,7 @@ ssize_t copy_oldmem_page(unsigned long pfn, char *buf, size_t csize, unsigned long offset, int userbuf) { unsigned long src; + int rc; if (!csize) return 0; @@ -43,11 +86,11 @@ ssize_t copy_oldmem_page(unsigned long pfn, char *buf, src < OLDMEM_BASE + OLDMEM_SIZE) src -= OLDMEM_BASE; if (userbuf) - copy_to_user_real((void __force __user *) buf, (void *) src, - csize); + rc = copy_to_user_real((void __force __user *) buf, + (void *) src, csize); else - memcpy_real(buf, (void *) src, csize); - return csize; + rc = copy_page_real(buf, (void *) src, csize); + return (rc == 0) ? csize : rc; } /* -- cgit v1.2.3-70-g09d2 From a39a9f7b6608c83b89ae404cc39e6607ccdccdde Mon Sep 17 00:00:00 2001 From: Rohit Vaswani Date: Tue, 18 Jun 2013 18:53:31 -0700 Subject: ARM: msm: dts: Fix the gpio register address for msm8960 Fix the the gpio reg address for the device tree entry. Signed-off-by: Rohit Vaswani Signed-off-by: David Brown --- arch/arm/boot/dts/msm8960-cdp.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/msm8960-cdp.dts b/arch/arm/boot/dts/msm8960-cdp.dts index db2060c4654..9c1167b0459 100644 --- a/arch/arm/boot/dts/msm8960-cdp.dts +++ b/arch/arm/boot/dts/msm8960-cdp.dts @@ -26,7 +26,7 @@ cpu-offset = <0x80000>; }; - msmgpio: gpio@fd510000 { + msmgpio: gpio@800000 { compatible = "qcom,msm-gpio"; gpio-controller; #gpio-cells = <2>; @@ -34,7 +34,7 @@ interrupts = <0 32 0x4>; interrupt-controller; #interrupt-cells = <2>; - reg = <0xfd510000 0x4000>; + reg = <0x800000 0x4000>; }; serial@16440000 { -- cgit v1.2.3-70-g09d2 From 976f39b139cdd06a88a5aadd8202b0c30cac9cda Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Wed, 17 Jul 2013 17:56:31 +0000 Subject: MIPS: BMIPS: Fix thinko to release slave TP from reset Commit 4df715aa ["MIPS: BMIPS: support booting from physical CPU other than 0"] introduced a thinko which will prevents slave CPUs from being released from reset on systems where we boot from TP0. The problem is that we are checking whether the slave CPU logical CPU map is 0, which is never true for systems booting from TP0, so we do not release the slave TP from reset and we are just stuck. Fix this by properly checking that the CPU we intend to boot really is the physical slave CPU (logical and physical value being 1). Signed-off-by: Florian Fainelli Cc: linux-mips@linux-mips.org Cc: blogic@openwrt.org Cc: jogo@openwrt.org Cc: cernekee@gmail.com Cc: Florian Fainelli Patchwork: https://patchwork.linux-mips.org/patch/5598/ Signed-off-by: Ralf Baechle --- arch/mips/kernel/smp-bmips.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/kernel/smp-bmips.c b/arch/mips/kernel/smp-bmips.c index aea6c088583..67445374014 100644 --- a/arch/mips/kernel/smp-bmips.c +++ b/arch/mips/kernel/smp-bmips.c @@ -173,7 +173,7 @@ static void bmips_boot_secondary(int cpu, struct task_struct *idle) else { #if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) /* Reset slave TP1 if booting from TP0 */ - if (cpu_logical_map(cpu) == 0) + if (cpu_logical_map(cpu) == 1) set_c0_brcm_cmt_ctrl(0x01); #elif defined(CONFIG_CPU_BMIPS5000) if (cpu & 0x01) -- cgit v1.2.3-70-g09d2 From afc813ae6d01eb4bb03fe67ed74c76608e3db089 Mon Sep 17 00:00:00 2001 From: Tony Wu Date: Thu, 18 Jul 2013 09:45:47 +0000 Subject: MIPS: tlbex: Fix typo in r3000 tlb store handler commit 6ba045f (MIPS: Move generated code to .text for microMIPS) causes a panic at boot. The handler builder should test against handle_tlbs_end, not handle_tlbs. Signed-off-by: Tony Wu Acked-by: Jayachandran C. Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5600/ Signed-off-by: Ralf Baechle --- arch/mips/mm/tlbex.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/mm/tlbex.c b/arch/mips/mm/tlbex.c index 9ab0f907a52..605b6fc1369 100644 --- a/arch/mips/mm/tlbex.c +++ b/arch/mips/mm/tlbex.c @@ -1803,7 +1803,7 @@ static void __cpuinit build_r3000_tlb_store_handler(void) uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff); uasm_i_nop(&p); - if (p >= handle_tlbs) + if (p >= handle_tlbs_end) panic("TLB store handler fastpath space exceeded"); uasm_resolve_relocs(relocs, labels); -- cgit v1.2.3-70-g09d2 From 35ac7840bca23a0fcfb53cc433ae1fd6dc6d35c0 Mon Sep 17 00:00:00 2001 From: Ganesan Ramalingam Date: Wed, 17 Jul 2013 10:27:25 +0000 Subject: MIPS: Netlogic: Fix USB block's coherent DMA mask The on-chip USB controller on Netlogic XLP does not suppport DMA beyond 32-bit physical address. Set the coherent_dma_mask of the USB in its PCI fixup to support this. Signed-off-by: Ganesan Ramalingam Signed-off-by: Jayachandran C. Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5596/ Signed-off-by: Ralf Baechle --- arch/mips/netlogic/xlp/usb-init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/netlogic/xlp/usb-init.c b/arch/mips/netlogic/xlp/usb-init.c index 9c401dd7833..ef3897ef0dc 100644 --- a/arch/mips/netlogic/xlp/usb-init.c +++ b/arch/mips/netlogic/xlp/usb-init.c @@ -119,7 +119,7 @@ static u64 xlp_usb_dmamask = ~(u32)0; static void nlm_usb_fixup_final(struct pci_dev *dev) { dev->dev.dma_mask = &xlp_usb_dmamask; - dev->dev.coherent_dma_mask = DMA_BIT_MASK(64); + dev->dev.coherent_dma_mask = DMA_BIT_MASK(32); switch (dev->devfn) { case 0x10: dev->irq = PIC_EHCI_0_IRQ; -- cgit v1.2.3-70-g09d2 From 628f0650ea65ef2ec0a2bde141c271dea1d18904 Mon Sep 17 00:00:00 2001 From: Jayachandran C Date: Wed, 17 Jul 2013 10:27:26 +0000 Subject: MIPS: Netlogic: Add XLP PIC irqdomain Add a legacy irq domain for the XLP PIC interrupts. This will be used when interrupts are assigned from the device tree. This change is required after commit c5cdc67 "irqdomain: Remove temporary MIPS workaround code". Signed-off-by: Jayachandran C Cc: linux-mips@linux-mips.org Cc: Jayachandran C Patchwork: https://patchwork.linux-mips.org/patch/5597/ Signed-off-by: Ralf Baechle --- arch/mips/netlogic/common/irq.c | 68 ++++++++++++++++++++++++++++++++------ arch/mips/netlogic/dts/xlp_evp.dts | 3 +- arch/mips/netlogic/dts/xlp_svp.dts | 3 +- 3 files changed, 61 insertions(+), 13 deletions(-) (limited to 'arch') diff --git a/arch/mips/netlogic/common/irq.c b/arch/mips/netlogic/common/irq.c index 73facb2b33b..1c7e3a1b81a 100644 --- a/arch/mips/netlogic/common/irq.c +++ b/arch/mips/netlogic/common/irq.c @@ -40,6 +40,10 @@ #include #include +#include +#include +#include + #include #include #include @@ -223,17 +227,6 @@ static void nlm_init_node_irqs(int node) nodep->irqmask = irqmask; } -void __init arch_init_irq(void) -{ - /* Initialize the irq descriptors */ - nlm_init_percpu_irqs(); - nlm_init_node_irqs(0); - write_c0_eimr(nlm_current_node()->irqmask); -#if defined(CONFIG_CPU_XLR) - nlm_setup_fmn_irq(); -#endif -} - void nlm_smp_irq_init(int hwcpuid) { int node, cpu; @@ -266,3 +259,56 @@ asmlinkage void plat_irq_dispatch(void) /* top level irq handling */ do_IRQ(nlm_irq_to_xirq(node, i)); } + +#ifdef CONFIG_OF +static struct irq_domain *xlp_pic_domain; + +static const struct irq_domain_ops xlp_pic_irq_domain_ops = { + .xlate = irq_domain_xlate_onetwocell, +}; + +static int __init xlp_of_pic_init(struct device_node *node, + struct device_node *parent) +{ + const int n_picirqs = PIC_IRT_LAST_IRQ - PIC_IRQ_BASE + 1; + struct resource res; + int socid, ret; + + /* we need a hack to get the PIC's SoC chip id */ + ret = of_address_to_resource(node, 0, &res); + if (ret < 0) { + pr_err("PIC %s: reg property not found!\n", node->name); + return -EINVAL; + } + socid = (res.start >> 18) & 0x3; + xlp_pic_domain = irq_domain_add_legacy(node, n_picirqs, + nlm_irq_to_xirq(socid, PIC_IRQ_BASE), PIC_IRQ_BASE, + &xlp_pic_irq_domain_ops, NULL); + if (xlp_pic_domain == NULL) { + pr_err("PIC %s: Creating legacy domain failed!\n", node->name); + return -EINVAL; + } + pr_info("Node %d: IRQ domain created for PIC@%pa\n", socid, + &res.start); + return 0; +} + +static struct of_device_id __initdata xlp_pic_irq_ids[] = { + { .compatible = "netlogic,xlp-pic", .data = xlp_of_pic_init }, + {}, +}; +#endif + +void __init arch_init_irq(void) +{ + /* Initialize the irq descriptors */ + nlm_init_percpu_irqs(); + nlm_init_node_irqs(0); + write_c0_eimr(nlm_current_node()->irqmask); +#if defined(CONFIG_CPU_XLR) + nlm_setup_fmn_irq(); +#endif +#if defined(CONFIG_OF) + of_irq_init(xlp_pic_irq_ids); +#endif +} diff --git a/arch/mips/netlogic/dts/xlp_evp.dts b/arch/mips/netlogic/dts/xlp_evp.dts index e14f4230806..06407033678 100644 --- a/arch/mips/netlogic/dts/xlp_evp.dts +++ b/arch/mips/netlogic/dts/xlp_evp.dts @@ -76,10 +76,11 @@ }; }; pic: pic@4000 { - interrupt-controller; + compatible = "netlogic,xlp-pic"; #address-cells = <0>; #interrupt-cells = <1>; reg = <0 0x4000 0x200>; + interrupt-controller; }; nor_flash@1,0 { diff --git a/arch/mips/netlogic/dts/xlp_svp.dts b/arch/mips/netlogic/dts/xlp_svp.dts index 8af4bdbe5d9..9c5db102df5 100644 --- a/arch/mips/netlogic/dts/xlp_svp.dts +++ b/arch/mips/netlogic/dts/xlp_svp.dts @@ -76,10 +76,11 @@ }; }; pic: pic@4000 { - interrupt-controller; + compatible = "netlogic,xlp-pic"; #address-cells = <0>; #interrupt-cells = <1>; reg = <0 0x4000 0x200>; + interrupt-controller; }; nor_flash@1,0 { -- cgit v1.2.3-70-g09d2 From 38a997a70e6cf0ee9fc26de146601ba10fa552a4 Mon Sep 17 00:00:00 2001 From: Aaro Koskinen Date: Mon, 15 Jul 2013 07:21:57 +0000 Subject: MIPS: tlbex: fix broken build in v3.11-rc1 Commit 6ba045f9fbdafb48da42aa8576ea7a3980443136 (MIPS: Move generated code to .text for microMIPS) deleted tlbmiss_handler_setup_pgd_array, but some references were not converted. Fix that to enable building a MIPS kernel. Signed-off-by: Aaro Koskinen Acked-by: Jayachandran C. Acked-by: David Daney Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5589/ Signed-off-by: Ralf Baechle --- arch/mips/mm/tlbex.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/mm/tlbex.c b/arch/mips/mm/tlbex.c index 605b6fc1369..523775d7a20 100644 --- a/arch/mips/mm/tlbex.c +++ b/arch/mips/mm/tlbex.c @@ -1466,7 +1466,7 @@ static void __cpuinit build_r4000_setup_pgd(void) { const int a0 = 4; const int a1 = 5; - u32 *p = tlbmiss_handler_setup_pgd_array; + u32 *p = tlbmiss_handler_setup_pgd; const int tlbmiss_handler_setup_pgd_size = tlbmiss_handler_setup_pgd_end - tlbmiss_handler_setup_pgd; struct uasm_label *l = labels; -- cgit v1.2.3-70-g09d2 From f2a5b1d78c076c525d20176d227faf2e6a20257c Mon Sep 17 00:00:00 2001 From: James Hogan Date: Fri, 12 Jul 2013 10:26:11 +0000 Subject: MIPS: KVM: Mark KVM_GUEST (T&E KVM) as BROKEN_ON_SMP Make KVM_GUEST depend on BROKEN_ON_SMP so that it cannot be enabled with SMP. SMP kernels use ll/sc instructions for an atomic section in the tlb fill handler, with a tlbp instruction contained in the middle. This cannot be emulated with trap & emulate KVM because the tlbp instruction traps and the eret to return to the guest code clears the LLbit which makes the sc instruction always fail. Signed-off-by: James Hogan Cc: Sanjay Lal Cc: Ralf Baechle Cc: David Daney Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/5588/ Signed-off-by: Ralf Baechle --- arch/mips/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 4758a8fd3e9..c3abed33230 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -1702,6 +1702,7 @@ endchoice config KVM_GUEST bool "KVM Guest Kernel" + depends on BROKEN_ON_SMP help Select this option if building a guest kernel for KVM (Trap & Emulate) mode -- cgit v1.2.3-70-g09d2 From 3179ce7254ffa43f3ba4409f31a954ecc4a8d408 Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Sat, 11 May 2013 15:35:32 +0200 Subject: um: Fix return value of strnlen_user() In case of an error it must not return -EFAULT. Return 0 like all other archs do. Reported-by: toralf.foerster@gmx.de Signed-off-by: Richard Weinberger --- arch/um/kernel/skas/uaccess.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/um/kernel/skas/uaccess.c b/arch/um/kernel/skas/uaccess.c index 1d3e0c17340..4ffb644d6c0 100644 --- a/arch/um/kernel/skas/uaccess.c +++ b/arch/um/kernel/skas/uaccess.c @@ -254,6 +254,6 @@ int strnlen_user(const void __user *str, int len) n = buffer_op((unsigned long) str, len, 0, strnlen_chunk, &count); if (n == 0) return count + 1; - return -EFAULT; + return 0; } EXPORT_SYMBOL(strnlen_user); -- cgit v1.2.3-70-g09d2 From dee20035b42d569984d2c16041b51e4d75e233b5 Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Sun, 12 May 2013 23:26:03 +0200 Subject: um: Mark stub pages mapping with VM_PFNMAP Ensure that a process cannot destroy his stub pages with using MADV_DONTNEED and friends. Reported-by: toralf.foerster@gmx.de Signed-off-by: Richard Weinberger --- arch/um/kernel/skas/mmu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/um/kernel/skas/mmu.c b/arch/um/kernel/skas/mmu.c index ff03067a3b1..007d5503f49 100644 --- a/arch/um/kernel/skas/mmu.c +++ b/arch/um/kernel/skas/mmu.c @@ -123,7 +123,7 @@ void uml_setup_stubs(struct mm_struct *mm) /* dup_mmap already holds mmap_sem */ err = install_special_mapping(mm, STUB_START, STUB_END - STUB_START, VM_READ | VM_MAYREAD | VM_EXEC | - VM_MAYEXEC | VM_DONTCOPY, + VM_MAYEXEC | VM_DONTCOPY | VM_PFNMAP, mm->context.stub_pages); if (err) { printk(KERN_ERR "install_special_mapping returned %d\n", err); -- cgit v1.2.3-70-g09d2 From 0974a9cadc7886f7baaa458bb0c89f5c5f9d458e Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Fri, 17 May 2013 14:21:01 +0200 Subject: um: Fix wait_stub_done() error handling If we die within a stub handler we only way to reliable kill the (obviously) dying uml guest process is killing it's host twin on the host side. Signed-off-by: Richard Weinberger --- arch/um/os-Linux/skas/process.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/um/os-Linux/skas/process.c b/arch/um/os-Linux/skas/process.c index 4625949bf1e..441e4ba074f 100644 --- a/arch/um/os-Linux/skas/process.c +++ b/arch/um/os-Linux/skas/process.c @@ -54,7 +54,7 @@ static int ptrace_dump_regs(int pid) void wait_stub_done(int pid) { - int n, status, err; + int n, status, err, bad_stop = 0; while (1) { CATCH_EINTR(n = waitpid(pid, &status, WUNTRACED | __WALL)); @@ -74,6 +74,8 @@ void wait_stub_done(int pid) if (((1 << WSTOPSIG(status)) & STUB_DONE_MASK) != 0) return; + else + bad_stop = 1; bad_wait: err = ptrace_dump_regs(pid); @@ -83,7 +85,10 @@ bad_wait: printk(UM_KERN_ERR "wait_stub_done : failed to wait for SIGTRAP, " "pid = %d, n = %d, errno = %d, status = 0x%x\n", pid, n, errno, status); - fatal_sigsegv(); + if (bad_stop) + kill(pid, SIGKILL); + else + fatal_sigsegv(); } extern unsigned long current_stub_stack(void); -- cgit v1.2.3-70-g09d2 From 7473534130c3156d199512c99ff1b796233e8547 Mon Sep 17 00:00:00 2001 From: Tristan Schmelcher Date: Mon, 8 Jul 2013 16:19:49 -0400 Subject: uml: Fix which_tmpdir failure when /dev/shm is a symlink, and in other edge cases which_tmpdir did the wrong thing if /dev/shm was a symlink (e.g., to /run/shm), if there were multiple mounts on top of each other, if the mount(s) were obscured by a later mount, or if /dev/shm was a prefix of another mount point. This fixes these cases. Applies to 3.9.6. Signed-off-by: Tristan Schmelcher Signed-off-by: Richard Weinberger --- arch/um/os-Linux/mem.c | 230 ++++++++++++++++++++++++++++++++++++++++--------- 1 file changed, 189 insertions(+), 41 deletions(-) (limited to 'arch') diff --git a/arch/um/os-Linux/mem.c b/arch/um/os-Linux/mem.c index ba4398056fe..3c4af77e51a 100644 --- a/arch/um/os-Linux/mem.c +++ b/arch/um/os-Linux/mem.c @@ -52,6 +52,25 @@ static void __init find_tempdir(void) strcat(tempdir, "/"); } +/* + * Remove bytes from the front of the buffer and refill it so that if there's a + * partial string that we care about, it will be completed, and we can recognize + * it. + */ +static int pop(int fd, char *buf, size_t size, size_t npop) +{ + ssize_t n; + size_t len = strlen(&buf[npop]); + + memmove(buf, &buf[npop], len + 1); + n = read(fd, &buf[len], size - len - 1); + if (n < 0) + return -errno; + + buf[len + n] = '\0'; + return 1; +} + /* * This will return 1, with the first character in buf being the * character following the next instance of c in the file. This will @@ -61,7 +80,6 @@ static void __init find_tempdir(void) static int next(int fd, char *buf, size_t size, char c) { ssize_t n; - size_t len; char *ptr; while ((ptr = strchr(buf, c)) == NULL) { @@ -74,20 +92,129 @@ static int next(int fd, char *buf, size_t size, char c) buf[n] = '\0'; } - ptr++; - len = strlen(ptr); - memmove(buf, ptr, len + 1); + return pop(fd, buf, size, ptr - buf + 1); +} + +/* + * Decode an octal-escaped and space-terminated path of the form used by + * /proc/mounts. May be used to decode a path in-place. "out" must be at least + * as large as the input. The output is always null-terminated. "len" gets the + * length of the output, excluding the trailing null. Returns 0 if a full path + * was successfully decoded, otherwise an error. + */ +static int decode_path(const char *in, char *out, size_t *len) +{ + char *first = out; + int c; + int i; + int ret = -EINVAL; + while (1) { + switch (*in) { + case '\0': + goto out; + + case ' ': + ret = 0; + goto out; + + case '\\': + in++; + c = 0; + for (i = 0; i < 3; i++) { + if (*in < '0' || *in > '7') + goto out; + c = (c << 3) | (*in++ - '0'); + } + *(unsigned char *)out++ = (unsigned char) c; + break; + + default: + *out++ = *in++; + break; + } + } + +out: + *out = '\0'; + *len = out - first; + return ret; +} + +/* + * Computes the length of s when encoded with three-digit octal escape sequences + * for the characters in chars. + */ +static size_t octal_encoded_length(const char *s, const char *chars) +{ + size_t len = strlen(s); + while ((s = strpbrk(s, chars)) != NULL) { + len += 3; + s++; + } + + return len; +} + +enum { + OUTCOME_NOTHING_MOUNTED, + OUTCOME_TMPFS_MOUNT, + OUTCOME_NON_TMPFS_MOUNT, +}; + +/* Read a line of /proc/mounts data looking for a tmpfs mount at "path". */ +static int read_mount(int fd, char *buf, size_t bufsize, const char *path, + int *outcome) +{ + int found; + int match; + char *space; + size_t len; + + enum { + MATCH_NONE, + MATCH_EXACT, + MATCH_PARENT, + }; + + found = next(fd, buf, bufsize, ' '); + if (found != 1) + return found; /* - * Refill the buffer so that if there's a partial string that we care - * about, it will be completed, and we can recognize it. + * If there's no following space in the buffer, then this path is + * truncated, so it can't be the one we're looking for. */ - n = read(fd, &buf[len], size - len - 1); - if (n < 0) - return -errno; + space = strchr(buf, ' '); + if (space) { + match = MATCH_NONE; + if (!decode_path(buf, buf, &len)) { + if (!strcmp(buf, path)) + match = MATCH_EXACT; + else if (!strncmp(buf, path, len) + && (path[len] == '/' || !strcmp(buf, "/"))) + match = MATCH_PARENT; + } + + found = pop(fd, buf, bufsize, space - buf + 1); + if (found != 1) + return found; + + switch (match) { + case MATCH_EXACT: + if (!strncmp(buf, "tmpfs", strlen("tmpfs"))) + *outcome = OUTCOME_TMPFS_MOUNT; + else + *outcome = OUTCOME_NON_TMPFS_MOUNT; + break; - buf[len + n] = '\0'; - return 1; + case MATCH_PARENT: + /* This mount obscures any previous ones. */ + *outcome = OUTCOME_NOTHING_MOUNTED; + break; + } + } + + return next(fd, buf, bufsize, '\n'); } /* which_tmpdir is called only during early boot */ @@ -106,8 +233,12 @@ static int checked_tmpdir = 0; */ static void which_tmpdir(void) { - int fd, found; - char buf[128] = { '\0' }; + int fd; + int found; + int outcome; + char *path; + char *buf; + size_t bufsize; if (checked_tmpdir) return; @@ -116,49 +247,66 @@ static void which_tmpdir(void) printf("Checking for tmpfs mount on /dev/shm..."); + path = realpath("/dev/shm", NULL); + if (!path) { + printf("failed to check real path, errno = %d\n", errno); + return; + } + printf("%s...", path); + + /* + * The buffer needs to be able to fit the full octal-escaped path, a + * space, and a trailing null in order to successfully decode it. + */ + bufsize = octal_encoded_length(path, " \t\n\\") + 2; + + if (bufsize < 128) + bufsize = 128; + + buf = malloc(bufsize); + if (!buf) { + printf("malloc failed, errno = %d\n", errno); + goto out; + } + buf[0] = '\0'; + fd = open("/proc/mounts", O_RDONLY); if (fd < 0) { printf("failed to open /proc/mounts, errno = %d\n", errno); - return; + goto out1; } + outcome = OUTCOME_NOTHING_MOUNTED; while (1) { - found = next(fd, buf, ARRAY_SIZE(buf), ' '); - if (found != 1) - break; - - if (!strncmp(buf, "/dev/shm", strlen("/dev/shm"))) - goto found; - - found = next(fd, buf, ARRAY_SIZE(buf), '\n'); + found = read_mount(fd, buf, bufsize, path, &outcome); if (found != 1) break; } -err: - if (found == 0) - printf("nothing mounted on /dev/shm\n"); - else if (found < 0) + if (found < 0) { printf("read returned errno %d\n", -found); + } else { + switch (outcome) { + case OUTCOME_TMPFS_MOUNT: + printf("OK\n"); + default_tmpdir = "/dev/shm"; + break; -out: - close(fd); - - return; - -found: - found = next(fd, buf, ARRAY_SIZE(buf), ' '); - if (found != 1) - goto err; + case OUTCOME_NON_TMPFS_MOUNT: + printf("not tmpfs\n"); + break; - if (strncmp(buf, "tmpfs", strlen("tmpfs"))) { - printf("not tmpfs\n"); - goto out; + default: + printf("nothing mounted on /dev/shm\n"); + break; + } } - printf("OK\n"); - default_tmpdir = "/dev/shm"; - goto out; + close(fd); +out1: + free(buf); +out: + free(path); } static int __init make_tempfile(const char *template, char **out_tempname, -- cgit v1.2.3-70-g09d2 From ab2bb148c5932712d2717a7f3a452846f07a660a Mon Sep 17 00:00:00 2001 From: Faidon Liambotis Date: Thu, 11 Jul 2013 21:08:09 +0000 Subject: MIPS: Octeon: Fix DT pruning bug with pip ports During the pruning of the device tree octeon_fdt_pip_iface() is called for each PIP interface and every port up to the port count is removed from the device tree. However, the count was set to the return value of cvmx_helper_interface_enumerate() which doesn't actually return the count but just returns zero on success. This effectively removed *all* ports from the tree. Use cvmx_helper_ports_on_interface() instead to fix this. This successfully restores the 3 ports of my ERLite-3 and fixes the "kernel assigns random MAC addresses" issue. Signed-off-by: Faidon Liambotis Tested-by: Aaro Koskinen Acked-by: David Daney Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5587/ Signed-off-by: Ralf Baechle --- arch/mips/cavium-octeon/octeon-platform.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/mips/cavium-octeon/octeon-platform.c b/arch/mips/cavium-octeon/octeon-platform.c index 7b746e7bf7a..1830874ff1e 100644 --- a/arch/mips/cavium-octeon/octeon-platform.c +++ b/arch/mips/cavium-octeon/octeon-platform.c @@ -334,9 +334,10 @@ static void __init octeon_fdt_pip_iface(int pip, int idx, u64 *pmac) char name_buffer[20]; int iface; int p; - int count; + int count = 0; - count = cvmx_helper_interface_enumerate(idx); + if (cvmx_helper_interface_enumerate(idx) == 0) + count = cvmx_helper_ports_on_interface(idx); snprintf(name_buffer, sizeof(name_buffer), "interface@%d", idx); iface = fdt_subnode_offset(initial_boot_params, pip, name_buffer); -- cgit v1.2.3-70-g09d2 From 9a8c1359571c5d5e2fbc43cf457a6486b70a70cb Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Fri, 19 Jul 2013 11:31:36 +0200 Subject: um: siginfo cleanup Currently we use both struct siginfo and siginfo_t. Let's use struct siginfo internally to avoid ongoing compiler warning. We are allowed to do so because struct siginfo and siginfo_t are equivalent. Signed-off-by: Richard Weinberger --- arch/um/include/shared/frame_kern.h | 8 ++++---- arch/um/kernel/signal.c | 4 ++-- arch/um/os-Linux/signal.c | 8 ++++---- arch/um/os-Linux/skas/process.c | 10 +++++----- 4 files changed, 15 insertions(+), 15 deletions(-) (limited to 'arch') diff --git a/arch/um/include/shared/frame_kern.h b/arch/um/include/shared/frame_kern.h index e584e40ee83..f2ca5702a4e 100644 --- a/arch/um/include/shared/frame_kern.h +++ b/arch/um/include/shared/frame_kern.h @@ -6,13 +6,13 @@ #ifndef __FRAME_KERN_H_ #define __FRAME_KERN_H_ -extern int setup_signal_stack_sc(unsigned long stack_top, int sig, +extern int setup_signal_stack_sc(unsigned long stack_top, int sig, struct k_sigaction *ka, - struct pt_regs *regs, + struct pt_regs *regs, sigset_t *mask); -extern int setup_signal_stack_si(unsigned long stack_top, int sig, +extern int setup_signal_stack_si(unsigned long stack_top, int sig, struct k_sigaction *ka, - struct pt_regs *regs, siginfo_t *info, + struct pt_regs *regs, struct siginfo *info, sigset_t *mask); #endif diff --git a/arch/um/kernel/signal.c b/arch/um/kernel/signal.c index 3e831b3fd07..f57e02e7910 100644 --- a/arch/um/kernel/signal.c +++ b/arch/um/kernel/signal.c @@ -19,7 +19,7 @@ EXPORT_SYMBOL(unblock_signals); * OK, we're invoking a handler */ static void handle_signal(struct pt_regs *regs, unsigned long signr, - struct k_sigaction *ka, siginfo_t *info) + struct k_sigaction *ka, struct siginfo *info) { sigset_t *oldset = sigmask_to_save(); int singlestep = 0; @@ -71,7 +71,7 @@ static void handle_signal(struct pt_regs *regs, unsigned long signr, static int kern_do_signal(struct pt_regs *regs) { struct k_sigaction ka_copy; - siginfo_t info; + struct siginfo info; int sig, handled_sig = 0; while ((sig = get_signal_to_deliver(&info, &ka_copy, regs, NULL)) > 0) { diff --git a/arch/um/os-Linux/signal.c b/arch/um/os-Linux/signal.c index 9d9f1b4bf82..905924b773d 100644 --- a/arch/um/os-Linux/signal.c +++ b/arch/um/os-Linux/signal.c @@ -25,7 +25,7 @@ void (*sig_info[NSIG])(int, struct siginfo *, struct uml_pt_regs *) = { [SIGIO] = sigio_handler, [SIGVTALRM] = timer_handler }; -static void sig_handler_common(int sig, siginfo_t *si, mcontext_t *mc) +static void sig_handler_common(int sig, struct siginfo *si, mcontext_t *mc) { struct uml_pt_regs r; int save_errno = errno; @@ -61,7 +61,7 @@ static void sig_handler_common(int sig, siginfo_t *si, mcontext_t *mc) static int signals_enabled; static unsigned int signals_pending; -void sig_handler(int sig, siginfo_t *si, mcontext_t *mc) +void sig_handler(int sig, struct siginfo *si, mcontext_t *mc) { int enabled; @@ -120,7 +120,7 @@ void set_sigstack(void *sig_stack, int size) panic("enabling signal stack failed, errno = %d\n", errno); } -static void (*handlers[_NSIG])(int sig, siginfo_t *si, mcontext_t *mc) = { +static void (*handlers[_NSIG])(int sig, struct siginfo *si, mcontext_t *mc) = { [SIGSEGV] = sig_handler, [SIGBUS] = sig_handler, [SIGILL] = sig_handler, @@ -162,7 +162,7 @@ static void hard_handler(int sig, siginfo_t *si, void *p) while ((sig = ffs(pending)) != 0){ sig--; pending &= ~(1 << sig); - (*handlers[sig])(sig, si, mc); + (*handlers[sig])(sig, (struct siginfo *)si, mc); } /* diff --git a/arch/um/os-Linux/skas/process.c b/arch/um/os-Linux/skas/process.c index 441e4ba074f..d531879a461 100644 --- a/arch/um/os-Linux/skas/process.c +++ b/arch/um/os-Linux/skas/process.c @@ -414,7 +414,7 @@ void userspace(struct uml_pt_regs *regs) if (WIFSTOPPED(status)) { int sig = WSTOPSIG(status); - ptrace(PTRACE_GETSIGINFO, pid, 0, &si); + ptrace(PTRACE_GETSIGINFO, pid, 0, (struct siginfo *)&si); switch (sig) { case SIGSEGV: @@ -422,7 +422,7 @@ void userspace(struct uml_pt_regs *regs) !ptrace_faultinfo) { get_skas_faultinfo(pid, ®s->faultinfo); - (*sig_info[SIGSEGV])(SIGSEGV, &si, + (*sig_info[SIGSEGV])(SIGSEGV, (struct siginfo *)&si, regs); } else handle_segv(pid, regs); @@ -431,14 +431,14 @@ void userspace(struct uml_pt_regs *regs) handle_trap(pid, regs, local_using_sysemu); break; case SIGTRAP: - relay_signal(SIGTRAP, &si, regs); + relay_signal(SIGTRAP, (struct siginfo *)&si, regs); break; case SIGVTALRM: now = os_nsecs(); if (now < nsecs) break; block_signals(); - (*sig_info[sig])(sig, &si, regs); + (*sig_info[sig])(sig, (struct siginfo *)&si, regs); unblock_signals(); nsecs = timer.it_value.tv_sec * UM_NSEC_PER_SEC + @@ -452,7 +452,7 @@ void userspace(struct uml_pt_regs *regs) case SIGFPE: case SIGWINCH: block_signals(); - (*sig_info[sig])(sig, &si, regs); + (*sig_info[sig])(sig, (struct siginfo *)&si, regs); unblock_signals(); break; default: -- cgit v1.2.3-70-g09d2 From 9e82d450531c79b18ab18c9b9645cdd9db31ee98 Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Fri, 19 Jul 2013 11:35:32 +0200 Subject: um: remove dead code "me" is not used. Signed-off-by: Richard Weinberger --- arch/x86/um/signal.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/um/signal.c b/arch/x86/um/signal.c index ae7319db18e..5e04a1c899f 100644 --- a/arch/x86/um/signal.c +++ b/arch/x86/um/signal.c @@ -508,7 +508,6 @@ int setup_signal_stack_si(unsigned long stack_top, int sig, { struct rt_sigframe __user *frame; int err = 0; - struct task_struct *me = current; frame = (struct rt_sigframe __user *) round_down(stack_top - sizeof(struct rt_sigframe), 16); -- cgit v1.2.3-70-g09d2 From f1b7001903dd5a80bdc9f777d2a741ccfd22ed4e Mon Sep 17 00:00:00 2001 From: Markos Chandras Date: Tue, 11 Jun 2013 09:02:33 +0000 Subject: MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION Virtualization does not always need KVM capabilities so drop the dependency. The KVM symbol already depends on HAVE_KVM. Fixes the following problem on a randconfig: warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet direct dependencies (HAVE_KVM) warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet direct dependencies (HAVE_KVM) Signed-off-by: Markos Chandras Acked-by: Steven J. Hill Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5443/ Signed-off-by: Ralf Baechle --- arch/mips/kvm/Kconfig | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/kvm/Kconfig b/arch/mips/kvm/Kconfig index 2c15590e55f..30e334e823b 100644 --- a/arch/mips/kvm/Kconfig +++ b/arch/mips/kvm/Kconfig @@ -5,7 +5,6 @@ source "virt/kvm/Kconfig" menuconfig VIRTUALIZATION bool "Virtualization" - depends on HAVE_KVM ---help--- Say Y here to get to see options for using your Linux host to run other operating systems inside virtual machines (guests). -- cgit v1.2.3-70-g09d2 From 53ae3acd4390ffeecb3a11dbd5be347b5a3d98f2 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Fri, 19 Jul 2013 15:08:15 +0100 Subject: arm64: Only enable local interrupts after the CPU is marked online There is a slight chance that (timer) interrupts are triggered before a secondary CPU has been marked online with implications on softirq thread affinity. Signed-off-by: Catalin Marinas Reported-by: Kirill Tkhai --- arch/arm64/kernel/smp.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm64/kernel/smp.c b/arch/arm64/kernel/smp.c index 5d54e3717bf..9c93e126328 100644 --- a/arch/arm64/kernel/smp.c +++ b/arch/arm64/kernel/smp.c @@ -199,13 +199,6 @@ asmlinkage void __cpuinit secondary_start_kernel(void) raw_spin_lock(&boot_lock); raw_spin_unlock(&boot_lock); - /* - * Enable local interrupts. - */ - notify_cpu_starting(cpu); - local_irq_enable(); - local_fiq_enable(); - /* * OK, now it's safe to let the boot CPU continue. Wait for * the CPU migration code to notice that the CPU is online @@ -214,6 +207,14 @@ asmlinkage void __cpuinit secondary_start_kernel(void) set_cpu_online(cpu, true); complete(&cpu_running); + /* + * Enable GIC and timers. + */ + notify_cpu_starting(cpu); + + local_irq_enable(); + local_fiq_enable(); + /* * OK, it's off to the idle thread for us */ -- cgit v1.2.3-70-g09d2 From c783c2815e13bbb0c0b99997cc240bd7e91b6bb8 Mon Sep 17 00:00:00 2001 From: Chen Gang Date: Mon, 24 Jun 2013 10:27:49 +0100 Subject: arm64: add '#ifdef CONFIG_COMPAT' for aarch32_break_handler() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit If 'COMPAT' not defined, aarch32_break_handler() cannot pass compiling, and it can work independent with 'COMPAT', so remove dummy definition. The related error: arch/arm64/kernel/debug-monitors.c:249:5: error: redefinition of ‘aarch32_break_handler’ In file included from arch/arm64/kernel/debug-monitors.c:29:0: /root/linux-next/arch/arm64/include/asm/debug-monitors.h:89:12: note: previous definition of ‘aarch32_break_handler’ was here Signed-off-by: Chen Gang Acked-by: Will Deacon Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/debug-monitors.h | 7 ------- 1 file changed, 7 deletions(-) (limited to 'arch') diff --git a/arch/arm64/include/asm/debug-monitors.h b/arch/arm64/include/asm/debug-monitors.h index ef8235c68c0..a2232d07be9 100644 --- a/arch/arm64/include/asm/debug-monitors.h +++ b/arch/arm64/include/asm/debug-monitors.h @@ -83,14 +83,7 @@ static inline int reinstall_suspended_bps(struct pt_regs *regs) } #endif -#ifdef CONFIG_COMPAT int aarch32_break_handler(struct pt_regs *regs); -#else -static int aarch32_break_handler(struct pt_regs *regs) -{ - return -EFAULT; -} -#endif #endif /* __ASSEMBLY */ #endif /* __KERNEL__ */ -- cgit v1.2.3-70-g09d2 From db6f41063cbdb58b14846e600e6bc3f4e4c2e888 Mon Sep 17 00:00:00 2001 From: Will Deacon Date: Fri, 19 Jul 2013 15:37:12 +0100 Subject: arm64: mm: don't treat user cache maintenance faults as writes On arm64, cache maintenance faults appear as data aborts with the CM bit set in the ESR. The WnR bit, usually used to distinguish between faulting loads and stores, always reads as 1 and (slightly confusingly) the instructions are treated as reads by the architecture. This patch fixes our fault handling code to treat cache maintenance faults in the same way as loads. Signed-off-by: Will Deacon Cc: Signed-off-by: Catalin Marinas --- arch/arm64/mm/fault.c | 46 ++++++++++++++++++++-------------------------- 1 file changed, 20 insertions(+), 26 deletions(-) (limited to 'arch') diff --git a/arch/arm64/mm/fault.c b/arch/arm64/mm/fault.c index 0ecac8980aa..6c8ba25bf6b 100644 --- a/arch/arm64/mm/fault.c +++ b/arch/arm64/mm/fault.c @@ -152,25 +152,8 @@ void do_bad_area(unsigned long addr, unsigned int esr, struct pt_regs *regs) #define ESR_CM (1 << 8) #define ESR_LNX_EXEC (1 << 24) -/* - * Check that the permissions on the VMA allow for the fault which occurred. - * If we encountered a write fault, we must have write permission, otherwise - * we allow any permission. - */ -static inline bool access_error(unsigned int esr, struct vm_area_struct *vma) -{ - unsigned int mask = VM_READ | VM_WRITE | VM_EXEC; - - if (esr & ESR_WRITE) - mask = VM_WRITE; - if (esr & ESR_LNX_EXEC) - mask = VM_EXEC; - - return vma->vm_flags & mask ? false : true; -} - static int __do_page_fault(struct mm_struct *mm, unsigned long addr, - unsigned int esr, unsigned int flags, + unsigned int mm_flags, unsigned long vm_flags, struct task_struct *tsk) { struct vm_area_struct *vma; @@ -188,12 +171,17 @@ static int __do_page_fault(struct mm_struct *mm, unsigned long addr, * it. */ good_area: - if (access_error(esr, vma)) { + /* + * Check that the permissions on the VMA allow for the fault which + * occurred. If we encountered a write or exec fault, we must have + * appropriate permissions, otherwise we allow any permission. + */ + if (!(vma->vm_flags & vm_flags)) { fault = VM_FAULT_BADACCESS; goto out; } - return handle_mm_fault(mm, vma, addr & PAGE_MASK, flags); + return handle_mm_fault(mm, vma, addr & PAGE_MASK, mm_flags); check_stack: if (vma->vm_flags & VM_GROWSDOWN && !expand_stack(vma, addr)) @@ -208,9 +196,15 @@ static int __kprobes do_page_fault(unsigned long addr, unsigned int esr, struct task_struct *tsk; struct mm_struct *mm; int fault, sig, code; - bool write = (esr & ESR_WRITE) && !(esr & ESR_CM); - unsigned int flags = FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE | - (write ? FAULT_FLAG_WRITE : 0); + unsigned long vm_flags = VM_READ | VM_WRITE | VM_EXEC; + unsigned int mm_flags = FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE; + + if (esr & ESR_LNX_EXEC) { + vm_flags = VM_EXEC; + } else if ((esr & ESR_WRITE) && !(esr & ESR_CM)) { + vm_flags = VM_WRITE; + mm_flags |= FAULT_FLAG_WRITE; + } tsk = current; mm = tsk->mm; @@ -248,7 +242,7 @@ retry: #endif } - fault = __do_page_fault(mm, addr, esr, flags, tsk); + fault = __do_page_fault(mm, addr, mm_flags, vm_flags, tsk); /* * If we need to retry but a fatal signal is pending, handle the @@ -265,7 +259,7 @@ retry: */ perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, addr); - if (flags & FAULT_FLAG_ALLOW_RETRY) { + if (mm_flags & FAULT_FLAG_ALLOW_RETRY) { if (fault & VM_FAULT_MAJOR) { tsk->maj_flt++; perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS_MAJ, 1, regs, @@ -280,7 +274,7 @@ retry: * Clear FAULT_FLAG_ALLOW_RETRY to avoid any risk of * starvation. */ - flags &= ~FAULT_FLAG_ALLOW_RETRY; + mm_flags &= ~FAULT_FLAG_ALLOW_RETRY; goto retry; } } -- cgit v1.2.3-70-g09d2 From ff701306cd49aaff80fb852323b387812bc76491 Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Thu, 11 Jul 2013 12:13:00 +0100 Subject: arm64: use common reboot infrastructure Commit 7b6d864b48d9 (reboot: arm: change reboot_mode to use enum reboot_mode) changed the way reboot is handled on arm, which has a direct impact on arm64 as we share the reset driver on the VE platform. The obvious fix is to move arm64 to use the same infrastructure. Signed-off-by: Marc Zyngier [catalin.marinas@arm.com: removed reboot_mode = REBOOT_HARD default setting] Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/system_misc.h | 3 ++- arch/arm64/kernel/process.c | 2 +- 2 files changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm64/include/asm/system_misc.h b/arch/arm64/include/asm/system_misc.h index a6e1750369e..7a18fabbe0f 100644 --- a/arch/arm64/include/asm/system_misc.h +++ b/arch/arm64/include/asm/system_misc.h @@ -23,6 +23,7 @@ #include #include #include +#include struct pt_regs; @@ -41,7 +42,7 @@ extern void show_pte(struct mm_struct *mm, unsigned long addr); extern void __show_regs(struct pt_regs *); void soft_restart(unsigned long); -extern void (*arm_pm_restart)(char str, const char *cmd); +extern void (*arm_pm_restart)(enum reboot_mode reboot_mode, const char *cmd); #define UDBG_UNDEFINED (1 << 0) #define UDBG_SYSCALL (1 << 1) diff --git a/arch/arm64/kernel/process.c b/arch/arm64/kernel/process.c index 46f02c3b501..1788bf6b471 100644 --- a/arch/arm64/kernel/process.c +++ b/arch/arm64/kernel/process.c @@ -132,7 +132,7 @@ void machine_restart(char *cmd) /* Now call the architecture specific reboot code. */ if (arm_pm_restart) - arm_pm_restart('h', cmd); + arm_pm_restart(reboot_mode, cmd); /* * Whoops - the architecture was unable to reboot. -- cgit v1.2.3-70-g09d2 From 29b7a47a9df2534ed62c4783dcf76153ceb76a73 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 12 Dec 2012 10:18:51 -0800 Subject: alpha: Convert print_symbol to %pSR Use the new vsprintf extension to avoid any possible message interleaving. Reviewed-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Joe Perches --- arch/alpha/kernel/traps.c | 8 +++----- 1 file changed, 3 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/alpha/kernel/traps.c b/arch/alpha/kernel/traps.c index be1fba334bd..bd0665cdc84 100644 --- a/arch/alpha/kernel/traps.c +++ b/arch/alpha/kernel/traps.c @@ -66,8 +66,8 @@ dik_show_regs(struct pt_regs *regs, unsigned long *r9_15) { printk("pc = [<%016lx>] ra = [<%016lx>] ps = %04lx %s\n", regs->pc, regs->r26, regs->ps, print_tainted()); - print_symbol("pc is at %s\n", regs->pc); - print_symbol("ra is at %s\n", regs->r26 ); + printk("pc is at %pSR\n", (void *)regs->pc); + printk("ra is at %pSR\n", (void *)regs->r26); printk("v0 = %016lx t0 = %016lx t1 = %016lx\n", regs->r0, regs->r1, regs->r2); printk("t2 = %016lx t3 = %016lx t4 = %016lx\n", @@ -132,9 +132,7 @@ dik_show_trace(unsigned long *sp) continue; if (tmp >= (unsigned long) &_etext) continue; - printk("[<%lx>]", tmp); - print_symbol(" %s", tmp); - printk("\n"); + printk("[<%lx>] %pSR\n", tmp, (void *)tmp); if (i > 40) { printk(" ..."); break; -- cgit v1.2.3-70-g09d2 From 00ee03092a6e4b1d0ddc6b861ebb9ed8d13cc29b Mon Sep 17 00:00:00 2001 From: Chen Gang Date: Wed, 29 May 2013 18:51:28 +0800 Subject: alpha: kernel: using memcpy() instead of strcpy() When sending message in send_secondary_console_msg(), the length is not include the NUL byte, and also not copy NUL to 'ipc_buffer'. When receive message in recv_secondary_console_msg(), the 'cnt' also excludes NUL. So when get string from ipc_buffer, it may not be NUL terminated. Then use memcpy() instead of strcpy(), and set last byte NUL. Reviewed-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Chen Gang --- arch/alpha/kernel/smp.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/alpha/kernel/smp.c b/arch/alpha/kernel/smp.c index 53b18a620e1..4bc3c414d07 100644 --- a/arch/alpha/kernel/smp.c +++ b/arch/alpha/kernel/smp.c @@ -266,7 +266,8 @@ recv_secondary_console_msg(void) else { cp1 = (char *) &cpu->ipc_buffer[11]; cp2 = buf; - strcpy(cp2, cp1); + memcpy(cp2, cp1, cnt); + cp2[cnt] = '\0'; while ((cp2 = strchr(cp2, '\r')) != 0) { *cp2 = ' '; -- cgit v1.2.3-70-g09d2 From 91b678c8edb7d8abd444705df63b80af31ad13e8 Mon Sep 17 00:00:00 2001 From: Chen Gang Date: Wed, 29 May 2013 19:04:09 +0800 Subject: alpha: kernel: typo issue, using '1' instead of '11' For sending message: *(unsigned int *)&cpu->ipc_buffer[0] = len; cp1 = (char *) &cpu->ipc_buffer[1]; But for receive message: cnt = cpu->ipc_buffer[0] >> 32; ... cp1 = (char *) &cpu->ipc_buffer[11]; They are not pairs, it is typo issue of the redundency '1'. So need use '1' instead of '11'. Reviewed-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Chen Gang --- arch/alpha/kernel/smp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/alpha/kernel/smp.c b/arch/alpha/kernel/smp.c index 4bc3c414d07..9dbbcb3b914 100644 --- a/arch/alpha/kernel/smp.c +++ b/arch/alpha/kernel/smp.c @@ -264,7 +264,7 @@ recv_secondary_console_msg(void) if (cnt <= 0 || cnt >= 80) strcpy(buf, "<<< BOGUS MSG >>>"); else { - cp1 = (char *) &cpu->ipc_buffer[11]; + cp1 = (char *) &cpu->ipc_buffer[1]; cp2 = buf; memcpy(cp2, cp1, cnt); cp2[cnt] = '\0'; -- cgit v1.2.3-70-g09d2 From 8b3ed3c002666540d9782a5219fa75c8a3fba98f Mon Sep 17 00:00:00 2001 From: Will Deacon Date: Fri, 21 Jun 2013 18:17:22 +0100 Subject: alpha: locks: remove unused arch_*_relax operations The arch_{spin,read,write}_relax macros are not used anywhere in the kernel and are typically just aliases for cpu_relax(). This patch removes the unused definitions for Alpha. Cc: Al Viro Reviewed-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Will Deacon --- arch/alpha/include/asm/spinlock.h | 4 ---- 1 file changed, 4 deletions(-) (limited to 'arch') diff --git a/arch/alpha/include/asm/spinlock.h b/arch/alpha/include/asm/spinlock.h index 3bba21e41b8..37b570d0120 100644 --- a/arch/alpha/include/asm/spinlock.h +++ b/arch/alpha/include/asm/spinlock.h @@ -168,8 +168,4 @@ static inline void arch_write_unlock(arch_rwlock_t * lock) #define arch_read_lock_flags(lock, flags) arch_read_lock(lock) #define arch_write_lock_flags(lock, flags) arch_write_lock(lock) -#define arch_spin_relax(lock) cpu_relax() -#define arch_read_relax(lock) cpu_relax() -#define arch_write_relax(lock) cpu_relax() - #endif /* _ALPHA_SPINLOCK_H */ -- cgit v1.2.3-70-g09d2 From 01350eb6c0d6fa7831b387d50e19830d8d0da354 Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Sat, 13 Jul 2013 13:31:51 -0700 Subject: alpha: Add kcmp and finit_module syscalls Reviewed-and-Tested-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/include/asm/unistd.h | 3 +-- arch/alpha/include/uapi/asm/unistd.h | 2 ++ arch/alpha/kernel/systbls.S | 2 ++ 3 files changed, 5 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/alpha/include/asm/unistd.h b/arch/alpha/include/asm/unistd.h index 43baee17acd..f2c94402e2c 100644 --- a/arch/alpha/include/asm/unistd.h +++ b/arch/alpha/include/asm/unistd.h @@ -3,8 +3,7 @@ #include - -#define NR_SYSCALLS 506 +#define NR_SYSCALLS 508 #define __ARCH_WANT_OLD_READDIR #define __ARCH_WANT_STAT64 diff --git a/arch/alpha/include/uapi/asm/unistd.h b/arch/alpha/include/uapi/asm/unistd.h index 801d28bcea5..53ae7bb1bfd 100644 --- a/arch/alpha/include/uapi/asm/unistd.h +++ b/arch/alpha/include/uapi/asm/unistd.h @@ -467,5 +467,7 @@ #define __NR_sendmmsg 503 #define __NR_process_vm_readv 504 #define __NR_process_vm_writev 505 +#define __NR_kcmp 506 +#define __NR_finit_module 507 #endif /* _UAPI_ALPHA_UNISTD_H */ diff --git a/arch/alpha/kernel/systbls.S b/arch/alpha/kernel/systbls.S index 4284ec798ec..dca9b3fb007 100644 --- a/arch/alpha/kernel/systbls.S +++ b/arch/alpha/kernel/systbls.S @@ -524,6 +524,8 @@ sys_call_table: .quad sys_sendmmsg .quad sys_process_vm_readv .quad sys_process_vm_writev /* 505 */ + .quad sys_kcmp + .quad sys_finit_module .size sys_call_table, . - sys_call_table .type sys_call_table, @object -- cgit v1.2.3-70-g09d2 From 6da7539734d4e0f5caeea1e0efbb74d7b83db1ca Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Thu, 11 Jul 2013 07:42:14 -0700 Subject: alpha: Improve atomic_add_unless Use ll/sc loops instead of C loops around cmpxchg. Update the atomic64_add_unless block comment to match the code. Reviewed-and-Tested-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/include/asm/atomic.h | 60 +++++++++++++++++++++++++---------------- 1 file changed, 37 insertions(+), 23 deletions(-) (limited to 'arch') diff --git a/arch/alpha/include/asm/atomic.h b/arch/alpha/include/asm/atomic.h index c2cbe4fc391..0dc18fc4d92 100644 --- a/arch/alpha/include/asm/atomic.h +++ b/arch/alpha/include/asm/atomic.h @@ -186,17 +186,24 @@ static __inline__ long atomic64_sub_return(long i, atomic64_t * v) */ static __inline__ int __atomic_add_unless(atomic_t *v, int a, int u) { - int c, old; - c = atomic_read(v); - for (;;) { - if (unlikely(c == (u))) - break; - old = atomic_cmpxchg((v), c, c + (a)); - if (likely(old == c)) - break; - c = old; - } - return c; + int c, new, old; + smp_mb(); + __asm__ __volatile__( + "1: ldl_l %[old],%[mem]\n" + " cmpeq %[old],%[u],%[c]\n" + " addl %[old],%[a],%[new]\n" + " bne %[c],2f\n" + " stl_c %[new],%[mem]\n" + " beq %[new],3f\n" + "2:\n" + ".subsection 2\n" + "3: br 1b\n" + ".previous" + : [old] "=&r"(old), [new] "=&r"(new), [c] "=&r"(c) + : [mem] "m"(*v), [a] "rI"(a), [u] "rI"((long)u) + : "memory"); + smp_mb(); + return old; } @@ -207,21 +214,28 @@ static __inline__ int __atomic_add_unless(atomic_t *v, int a, int u) * @u: ...unless v is equal to u. * * Atomically adds @a to @v, so long as it was not @u. - * Returns the old value of @v. + * Returns true iff @v was not @u. */ static __inline__ int atomic64_add_unless(atomic64_t *v, long a, long u) { - long c, old; - c = atomic64_read(v); - for (;;) { - if (unlikely(c == (u))) - break; - old = atomic64_cmpxchg((v), c, c + (a)); - if (likely(old == c)) - break; - c = old; - } - return c != (u); + long c, tmp; + smp_mb(); + __asm__ __volatile__( + "1: ldq_l %[tmp],%[mem]\n" + " cmpeq %[tmp],%[u],%[c]\n" + " addq %[tmp],%[a],%[tmp]\n" + " bne %[c],2f\n" + " stq_c %[tmp],%[mem]\n" + " beq %[tmp],3f\n" + "2:\n" + ".subsection 2\n" + "3: br 1b\n" + ".previous" + : [tmp] "=&r"(tmp), [c] "=&r"(c) + : [mem] "m"(*v), [a] "rI"(a), [u] "rI"(u) + : "memory"); + smp_mb(); + return !c; } #define atomic64_inc_not_zero(v) atomic64_add_unless((v), 1, 0) -- cgit v1.2.3-70-g09d2 From 748a76b5152e8f38edf8afbf6f4cd6e326ad9e62 Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Thu, 11 Jul 2013 08:04:20 -0700 Subject: alpha: Implement atomic64_dec_if_positive Reviewed-and-Tested-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/Kconfig | 1 + arch/alpha/include/asm/atomic.h | 28 ++++++++++++++++++++++++++++ 2 files changed, 29 insertions(+) (limited to 'arch') diff --git a/arch/alpha/Kconfig b/arch/alpha/Kconfig index 837a1f2d8b9..082d9b4b547 100644 --- a/arch/alpha/Kconfig +++ b/arch/alpha/Kconfig @@ -15,6 +15,7 @@ config ALPHA select ARCH_WANT_OPTIONAL_GPIOLIB select ARCH_WANT_IPC_PARSE_VERSION select ARCH_HAVE_NMI_SAFE_CMPXCHG + select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE select GENERIC_SMP_IDLE_THREAD select GENERIC_CMOS_UPDATE select GENERIC_STRNCPY_FROM_USER diff --git a/arch/alpha/include/asm/atomic.h b/arch/alpha/include/asm/atomic.h index 0dc18fc4d92..78b03ef39f6 100644 --- a/arch/alpha/include/asm/atomic.h +++ b/arch/alpha/include/asm/atomic.h @@ -238,6 +238,34 @@ static __inline__ int atomic64_add_unless(atomic64_t *v, long a, long u) return !c; } +/* + * atomic64_dec_if_positive - decrement by 1 if old value positive + * @v: pointer of type atomic_t + * + * The function returns the old value of *v minus 1, even if + * the atomic variable, v, was not decremented. + */ +static inline long atomic64_dec_if_positive(atomic64_t *v) +{ + long old, tmp; + smp_mb(); + __asm__ __volatile__( + "1: ldq_l %[old],%[mem]\n" + " subq %[old],1,%[tmp]\n" + " ble %[old],2f\n" + " stq_c %[tmp],%[mem]\n" + " beq %[tmp],3f\n" + "2:\n" + ".subsection 2\n" + "3: br 1b\n" + ".previous" + : [old] "=&r"(old), [tmp] "=&r"(tmp) + : [mem] "m"(*v) + : "memory"); + smp_mb(); + return old - 1; +} + #define atomic64_inc_not_zero(v) atomic64_add_unless((v), 1, 0) #define atomic_add_negative(a, v) (atomic_add_return((a), (v)) < 0) -- cgit v1.2.3-70-g09d2 From 231b0bedf55325ee5a1c7bdd47d00131dafc9ab7 Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Tue, 12 Apr 2011 14:45:12 -0700 Subject: alpha: Generate dwarf2 unwind info for various kernel entry points. Having unwind info past the PALcode generated stack frame makes debugging the kernel significantly easier. Acked-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/kernel/entry.S | 399 +++++++++++++++++++++++++++++++++------------- 1 file changed, 288 insertions(+), 111 deletions(-) (limited to 'arch') diff --git a/arch/alpha/kernel/entry.S b/arch/alpha/kernel/entry.S index f62a994ef12..a969b95ee5a 100644 --- a/arch/alpha/kernel/entry.S +++ b/arch/alpha/kernel/entry.S @@ -12,11 +12,32 @@ .text .set noat + .cfi_sections .debug_frame /* Stack offsets. */ #define SP_OFF 184 #define SWITCH_STACK_SIZE 320 +.macro CFI_START_OSF_FRAME func + .align 4 + .globl \func + .type \func,@function +\func: + .cfi_startproc simple + .cfi_return_column 64 + .cfi_def_cfa $sp, 48 + .cfi_rel_offset 64, 8 + .cfi_rel_offset $gp, 16 + .cfi_rel_offset $16, 24 + .cfi_rel_offset $17, 32 + .cfi_rel_offset $18, 40 +.endm + +.macro CFI_END_OSF_FRAME func + .cfi_endproc + .size \func, . - \func +.endm + /* * This defines the normal kernel pt-regs layout. * @@ -27,100 +48,158 @@ * the palcode-provided values are available to the signal handler. */ -#define SAVE_ALL \ - subq $sp, SP_OFF, $sp; \ - stq $0, 0($sp); \ - stq $1, 8($sp); \ - stq $2, 16($sp); \ - stq $3, 24($sp); \ - stq $4, 32($sp); \ - stq $28, 144($sp); \ - lda $2, alpha_mv; \ - stq $5, 40($sp); \ - stq $6, 48($sp); \ - stq $7, 56($sp); \ - stq $8, 64($sp); \ - stq $19, 72($sp); \ - stq $20, 80($sp); \ - stq $21, 88($sp); \ - ldq $2, HAE_CACHE($2); \ - stq $22, 96($sp); \ - stq $23, 104($sp); \ - stq $24, 112($sp); \ - stq $25, 120($sp); \ - stq $26, 128($sp); \ - stq $27, 136($sp); \ - stq $2, 152($sp); \ - stq $16, 160($sp); \ - stq $17, 168($sp); \ +.macro SAVE_ALL + subq $sp, SP_OFF, $sp + .cfi_adjust_cfa_offset SP_OFF + stq $0, 0($sp) + stq $1, 8($sp) + stq $2, 16($sp) + stq $3, 24($sp) + stq $4, 32($sp) + stq $28, 144($sp) + .cfi_rel_offset $0, 0 + .cfi_rel_offset $1, 8 + .cfi_rel_offset $2, 16 + .cfi_rel_offset $3, 24 + .cfi_rel_offset $4, 32 + .cfi_rel_offset $28, 144 + lda $2, alpha_mv + stq $5, 40($sp) + stq $6, 48($sp) + stq $7, 56($sp) + stq $8, 64($sp) + stq $19, 72($sp) + stq $20, 80($sp) + stq $21, 88($sp) + ldq $2, HAE_CACHE($2) + stq $22, 96($sp) + stq $23, 104($sp) + stq $24, 112($sp) + stq $25, 120($sp) + stq $26, 128($sp) + stq $27, 136($sp) + stq $2, 152($sp) + stq $16, 160($sp) + stq $17, 168($sp) stq $18, 176($sp) + .cfi_rel_offset $5, 40 + .cfi_rel_offset $6, 48 + .cfi_rel_offset $7, 56 + .cfi_rel_offset $8, 64 + .cfi_rel_offset $19, 72 + .cfi_rel_offset $20, 80 + .cfi_rel_offset $21, 88 + .cfi_rel_offset $22, 96 + .cfi_rel_offset $23, 104 + .cfi_rel_offset $24, 112 + .cfi_rel_offset $25, 120 + .cfi_rel_offset $26, 128 + .cfi_rel_offset $27, 136 +.endm -#define RESTORE_ALL \ - lda $19, alpha_mv; \ - ldq $0, 0($sp); \ - ldq $1, 8($sp); \ - ldq $2, 16($sp); \ - ldq $3, 24($sp); \ - ldq $21, 152($sp); \ - ldq $20, HAE_CACHE($19); \ - ldq $4, 32($sp); \ - ldq $5, 40($sp); \ - ldq $6, 48($sp); \ - ldq $7, 56($sp); \ - subq $20, $21, $20; \ - ldq $8, 64($sp); \ - beq $20, 99f; \ - ldq $20, HAE_REG($19); \ - stq $21, HAE_CACHE($19); \ - stq $21, 0($20); \ -99:; \ - ldq $19, 72($sp); \ - ldq $20, 80($sp); \ - ldq $21, 88($sp); \ - ldq $22, 96($sp); \ - ldq $23, 104($sp); \ - ldq $24, 112($sp); \ - ldq $25, 120($sp); \ - ldq $26, 128($sp); \ - ldq $27, 136($sp); \ - ldq $28, 144($sp); \ +.macro RESTORE_ALL + lda $19, alpha_mv + ldq $0, 0($sp) + ldq $1, 8($sp) + ldq $2, 16($sp) + ldq $3, 24($sp) + ldq $21, 152($sp) + ldq $20, HAE_CACHE($19) + ldq $4, 32($sp) + ldq $5, 40($sp) + ldq $6, 48($sp) + ldq $7, 56($sp) + subq $20, $21, $20 + ldq $8, 64($sp) + beq $20, 99f + ldq $20, HAE_REG($19) + stq $21, HAE_CACHE($19) + stq $21, 0($20) +99: ldq $19, 72($sp) + ldq $20, 80($sp) + ldq $21, 88($sp) + ldq $22, 96($sp) + ldq $23, 104($sp) + ldq $24, 112($sp) + ldq $25, 120($sp) + ldq $26, 128($sp) + ldq $27, 136($sp) + ldq $28, 144($sp) addq $sp, SP_OFF, $sp + .cfi_restore $0 + .cfi_restore $1 + .cfi_restore $2 + .cfi_restore $3 + .cfi_restore $4 + .cfi_restore $5 + .cfi_restore $6 + .cfi_restore $7 + .cfi_restore $8 + .cfi_restore $19 + .cfi_restore $20 + .cfi_restore $21 + .cfi_restore $22 + .cfi_restore $23 + .cfi_restore $24 + .cfi_restore $25 + .cfi_restore $26 + .cfi_restore $27 + .cfi_restore $28 + .cfi_adjust_cfa_offset -SP_OFF +.endm + +.macro DO_SWITCH_STACK + bsr $1, do_switch_stack + .cfi_adjust_cfa_offset SWITCH_STACK_SIZE + .cfi_rel_offset $9, 0 + .cfi_rel_offset $10, 8 + .cfi_rel_offset $11, 16 + .cfi_rel_offset $12, 24 + .cfi_rel_offset $13, 32 + .cfi_rel_offset $14, 40 + .cfi_rel_offset $15, 48 + /* We don't really care about the FP registers for debugging. */ +.endm + +.macro UNDO_SWITCH_STACK + bsr $1, undo_switch_stack + .cfi_restore $9 + .cfi_restore $10 + .cfi_restore $11 + .cfi_restore $12 + .cfi_restore $13 + .cfi_restore $14 + .cfi_restore $15 + .cfi_adjust_cfa_offset -SWITCH_STACK_SIZE +.endm /* * Non-syscall kernel entry points. */ - .align 4 - .globl entInt - .ent entInt -entInt: +CFI_START_OSF_FRAME entInt SAVE_ALL lda $8, 0x3fff lda $26, ret_from_sys_call bic $sp, $8, $8 mov $sp, $19 jsr $31, do_entInt -.end entInt +CFI_END_OSF_FRAME entInt - .align 4 - .globl entArith - .ent entArith -entArith: +CFI_START_OSF_FRAME entArith SAVE_ALL lda $8, 0x3fff lda $26, ret_from_sys_call bic $sp, $8, $8 mov $sp, $18 jsr $31, do_entArith -.end entArith +CFI_END_OSF_FRAME entArith - .align 4 - .globl entMM - .ent entMM -entMM: +CFI_START_OSF_FRAME entMM SAVE_ALL /* save $9 - $15 so the inline exception code can manipulate them. */ subq $sp, 56, $sp + .cfi_adjust_cfa_offset 56 stq $9, 0($sp) stq $10, 8($sp) stq $11, 16($sp) @@ -128,6 +207,13 @@ entMM: stq $13, 32($sp) stq $14, 40($sp) stq $15, 48($sp) + .cfi_rel_offset $9, 0 + .cfi_rel_offset $10, 8 + .cfi_rel_offset $11, 16 + .cfi_rel_offset $12, 24 + .cfi_rel_offset $13, 32 + .cfi_rel_offset $14, 40 + .cfi_rel_offset $15, 48 addq $sp, 56, $19 /* handle the fault */ lda $8, 0x3fff @@ -142,28 +228,33 @@ entMM: ldq $14, 40($sp) ldq $15, 48($sp) addq $sp, 56, $sp + .cfi_restore $9 + .cfi_restore $10 + .cfi_restore $11 + .cfi_restore $12 + .cfi_restore $13 + .cfi_restore $14 + .cfi_restore $15 + .cfi_adjust_cfa_offset -56 /* finish up the syscall as normal. */ br ret_from_sys_call -.end entMM +CFI_END_OSF_FRAME entMM - .align 4 - .globl entIF - .ent entIF -entIF: +CFI_START_OSF_FRAME entIF SAVE_ALL lda $8, 0x3fff lda $26, ret_from_sys_call bic $sp, $8, $8 mov $sp, $17 jsr $31, do_entIF -.end entIF +CFI_END_OSF_FRAME entIF - .align 4 - .globl entUna - .ent entUna -entUna: +CFI_START_OSF_FRAME entUna lda $sp, -256($sp) + .cfi_adjust_cfa_offset 256 stq $0, 0($sp) + .cfi_rel_offset $0, 0 + .cfi_remember_state ldq $0, 256($sp) /* get PS */ stq $1, 8($sp) stq $2, 16($sp) @@ -195,6 +286,32 @@ entUna: stq $28, 224($sp) mov $sp, $19 stq $gp, 232($sp) + .cfi_rel_offset $1, 1*8 + .cfi_rel_offset $2, 2*8 + .cfi_rel_offset $3, 3*8 + .cfi_rel_offset $4, 4*8 + .cfi_rel_offset $5, 5*8 + .cfi_rel_offset $6, 6*8 + .cfi_rel_offset $7, 7*8 + .cfi_rel_offset $8, 8*8 + .cfi_rel_offset $9, 9*8 + .cfi_rel_offset $10, 10*8 + .cfi_rel_offset $11, 11*8 + .cfi_rel_offset $12, 12*8 + .cfi_rel_offset $13, 13*8 + .cfi_rel_offset $14, 14*8 + .cfi_rel_offset $15, 15*8 + .cfi_rel_offset $19, 19*8 + .cfi_rel_offset $20, 20*8 + .cfi_rel_offset $21, 21*8 + .cfi_rel_offset $22, 22*8 + .cfi_rel_offset $23, 23*8 + .cfi_rel_offset $24, 24*8 + .cfi_rel_offset $25, 25*8 + .cfi_rel_offset $26, 26*8 + .cfi_rel_offset $27, 27*8 + .cfi_rel_offset $28, 28*8 + .cfi_rel_offset $29, 29*8 lda $8, 0x3fff stq $31, 248($sp) bic $sp, $8, $8 @@ -228,16 +345,45 @@ entUna: ldq $28, 224($sp) ldq $gp, 232($sp) lda $sp, 256($sp) + .cfi_restore $1 + .cfi_restore $2 + .cfi_restore $3 + .cfi_restore $4 + .cfi_restore $5 + .cfi_restore $6 + .cfi_restore $7 + .cfi_restore $8 + .cfi_restore $9 + .cfi_restore $10 + .cfi_restore $11 + .cfi_restore $12 + .cfi_restore $13 + .cfi_restore $14 + .cfi_restore $15 + .cfi_restore $19 + .cfi_restore $20 + .cfi_restore $21 + .cfi_restore $22 + .cfi_restore $23 + .cfi_restore $24 + .cfi_restore $25 + .cfi_restore $26 + .cfi_restore $27 + .cfi_restore $28 + .cfi_restore $29 + .cfi_adjust_cfa_offset -256 call_pal PAL_rti -.end entUna .align 4 - .ent entUnaUser entUnaUser: + .cfi_restore_state ldq $0, 0($sp) /* restore original $0 */ lda $sp, 256($sp) /* pop entUna's stack frame */ + .cfi_restore $0 + .cfi_adjust_cfa_offset -256 SAVE_ALL /* setup normal kernel stack */ lda $sp, -56($sp) + .cfi_adjust_cfa_offset 56 stq $9, 0($sp) stq $10, 8($sp) stq $11, 16($sp) @@ -245,6 +391,13 @@ entUnaUser: stq $13, 32($sp) stq $14, 40($sp) stq $15, 48($sp) + .cfi_rel_offset $9, 0 + .cfi_rel_offset $10, 8 + .cfi_rel_offset $11, 16 + .cfi_rel_offset $12, 24 + .cfi_rel_offset $13, 32 + .cfi_rel_offset $14, 40 + .cfi_rel_offset $15, 48 lda $8, 0x3fff addq $sp, 56, $19 bic $sp, $8, $8 @@ -257,20 +410,25 @@ entUnaUser: ldq $14, 40($sp) ldq $15, 48($sp) lda $sp, 56($sp) + .cfi_restore $9 + .cfi_restore $10 + .cfi_restore $11 + .cfi_restore $12 + .cfi_restore $13 + .cfi_restore $14 + .cfi_restore $15 + .cfi_adjust_cfa_offset -56 br ret_from_sys_call -.end entUnaUser +CFI_END_OSF_FRAME entUna - .align 4 - .globl entDbg - .ent entDbg -entDbg: +CFI_START_OSF_FRAME entDbg SAVE_ALL lda $8, 0x3fff lda $26, ret_from_sys_call bic $sp, $8, $8 mov $sp, $16 jsr $31, do_entDbg -.end entDbg +CFI_END_OSF_FRAME entDbg /* * The system call entry point is special. Most importantly, it looks @@ -285,8 +443,12 @@ entDbg: .align 4 .globl entSys - .globl ret_from_sys_call - .ent entSys + .type entSys, @function + .cfi_startproc simple + .cfi_return_column 64 + .cfi_def_cfa $sp, 48 + .cfi_rel_offset 64, 8 + .cfi_rel_offset $gp, 16 entSys: SAVE_ALL lda $8, 0x3fff @@ -300,6 +462,9 @@ entSys: stq $17, SP_OFF+32($sp) s8addq $0, $5, $5 stq $18, SP_OFF+40($sp) + .cfi_rel_offset $16, SP_OFF+24 + .cfi_rel_offset $17, SP_OFF+32 + .cfi_rel_offset $18, SP_OFF+40 blbs $3, strace beq $4, 1f ldq $27, 0($5) @@ -310,6 +475,7 @@ entSys: stq $31, 72($sp) /* a3=0 => no error */ .align 4 + .globl ret_from_sys_call ret_from_sys_call: cmovne $26, 0, $18 /* $18 = 0 => non-restartable */ ldq $0, SP_OFF($sp) @@ -324,10 +490,12 @@ ret_to_user: and $17, _TIF_WORK_MASK, $2 bne $2, work_pending restore_all: + .cfi_remember_state RESTORE_ALL call_pal PAL_rti ret_to_kernel: + .cfi_restore_state lda $16, 7 call_pal PAL_swpipl br restore_all @@ -356,7 +524,6 @@ $ret_success: stq $0, 0($sp) stq $31, 72($sp) /* a3=0 => no error */ br ret_from_sys_call -.end entSys /* * Do all cleanup when returning from all interrupts and system calls. @@ -370,7 +537,7 @@ $ret_success: */ .align 4 - .ent work_pending + .type work_pending, @function work_pending: and $17, _TIF_NOTIFY_RESUME | _TIF_SIGPENDING, $2 bne $2, $work_notifysig @@ -387,23 +554,22 @@ $work_resched: $work_notifysig: mov $sp, $16 - bsr $1, do_switch_stack + DO_SWITCH_STACK jsr $26, do_work_pending - bsr $1, undo_switch_stack + UNDO_SWITCH_STACK br restore_all -.end work_pending /* * PTRACE syscall handler */ .align 4 - .ent strace + .type strace, @function strace: /* set up signal stack, call syscall_trace */ - bsr $1, do_switch_stack + DO_SWITCH_STACK jsr $26, syscall_trace_enter /* returns the syscall number */ - bsr $1, undo_switch_stack + UNDO_SWITCH_STACK /* get the arguments back.. */ ldq $16, SP_OFF+24($sp) @@ -431,9 +597,9 @@ ret_from_straced: $strace_success: stq $0, 0($sp) /* save return value */ - bsr $1, do_switch_stack + DO_SWITCH_STACK jsr $26, syscall_trace_leave - bsr $1, undo_switch_stack + UNDO_SWITCH_STACK br $31, ret_from_sys_call .align 3 @@ -447,26 +613,31 @@ $strace_error: stq $0, 0($sp) stq $1, 72($sp) /* a3 for return */ - bsr $1, do_switch_stack + DO_SWITCH_STACK mov $18, $9 /* save old syscall number */ mov $19, $10 /* save old a3 */ jsr $26, syscall_trace_leave mov $9, $18 mov $10, $19 - bsr $1, undo_switch_stack + UNDO_SWITCH_STACK mov $31, $26 /* tell "ret_from_sys_call" we can restart */ br ret_from_sys_call -.end strace +CFI_END_OSF_FRAME entSys /* * Save and restore the switch stack -- aka the balance of the user context. */ .align 4 - .ent do_switch_stack + .type do_switch_stack, @function + .cfi_startproc simple + .cfi_return_column 64 + .cfi_def_cfa $sp, 0 + .cfi_register 64, $1 do_switch_stack: lda $sp, -SWITCH_STACK_SIZE($sp) + .cfi_adjust_cfa_offset SWITCH_STACK_SIZE stq $9, 0($sp) stq $10, 8($sp) stq $11, 16($sp) @@ -510,10 +681,14 @@ do_switch_stack: stt $f0, 312($sp) # save fpcr in slot of $f31 ldt $f0, 64($sp) # dont let "do_switch_stack" change fp state. ret $31, ($1), 1 -.end do_switch_stack + .cfi_endproc + .size do_switch_stack, .-do_switch_stack .align 4 - .ent undo_switch_stack + .type undo_switch_stack, @function + .cfi_startproc simple + .cfi_def_cfa $sp, 0 + .cfi_register 64, $1 undo_switch_stack: ldq $9, 0($sp) ldq $10, 8($sp) @@ -558,7 +733,8 @@ undo_switch_stack: ldt $f30, 304($sp) lda $sp, SWITCH_STACK_SIZE($sp) ret $31, ($1), 1 -.end undo_switch_stack + .cfi_endproc + .size undo_switch_stack, .-undo_switch_stack /* * The meat of the context switch code. @@ -566,17 +742,18 @@ undo_switch_stack: .align 4 .globl alpha_switch_to - .ent alpha_switch_to + .type alpha_switch_to, @function + .cfi_startproc alpha_switch_to: - .prologue 0 - bsr $1, do_switch_stack + DO_SWITCH_STACK call_pal PAL_swpctx lda $8, 0x3fff - bsr $1, undo_switch_stack + UNDO_SWITCH_STACK bic $sp, $8, $8 mov $17, $0 ret -.end alpha_switch_to + .cfi_endproc + .size alpha_switch_to, .-alpha_switch_to /* * New processes begin life here. -- cgit v1.2.3-70-g09d2 From e40600997249844933293859c2effa8b7468c97a Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Sat, 13 Jul 2013 16:21:05 -0700 Subject: alpha: Fix type compatibility warning for marvel_map_irq Acked-by: Phil Carmody Reviewed-and-Tested-by: Matt Turner Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/kernel/sys_marvel.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/alpha/kernel/sys_marvel.c b/arch/alpha/kernel/sys_marvel.c index 407accc8087..c92e389ff21 100644 --- a/arch/alpha/kernel/sys_marvel.c +++ b/arch/alpha/kernel/sys_marvel.c @@ -317,8 +317,9 @@ marvel_init_irq(void) } static int -marvel_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +marvel_map_irq(const struct pci_dev *cdev, u8 slot, u8 pin) { + struct pci_dev *dev = (struct pci_dev *)cdev; struct pci_controller *hose = dev->sysdata; struct io7_port *io7_port = hose->sysdata; struct io7 *io7 = io7_port->io7; -- cgit v1.2.3-70-g09d2 From 91531b0535e5556783a7da900cc115b5fec8e63f Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Thu, 18 Jul 2013 14:47:37 -0700 Subject: alpha: Use __builtin_alpha_rpcc As introduced in gcc 3.2. Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/kernel/time.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/alpha/kernel/time.c b/arch/alpha/kernel/time.c index e336694ca04..ea339503655 100644 --- a/arch/alpha/kernel/time.c +++ b/arch/alpha/kernel/time.c @@ -105,9 +105,7 @@ void arch_irq_work_raise(void) static inline __u32 rpcc(void) { - __u32 result; - asm volatile ("rpcc %0" : "=r"(result)); - return result; + return __builtin_alpha_rpcc(); } int update_persistent_clock(struct timespec now) -- cgit v1.2.3-70-g09d2 From 984ac6c0c7ad612d3e7d045243805de0a2702142 Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Thu, 28 Apr 2011 09:22:39 -0700 Subject: alpha: Don't if-out dp264_device_interrupt. The code as written is correct, and will be used by QEMU emulation. Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/kernel/sys_dp264.c | 8 -------- 1 file changed, 8 deletions(-) (limited to 'arch') diff --git a/arch/alpha/kernel/sys_dp264.c b/arch/alpha/kernel/sys_dp264.c index 5bf401f7ea9..6c35159bc00 100644 --- a/arch/alpha/kernel/sys_dp264.c +++ b/arch/alpha/kernel/sys_dp264.c @@ -190,9 +190,6 @@ static struct irq_chip clipper_irq_type = { static void dp264_device_interrupt(unsigned long vector) { -#if 1 - printk("dp264_device_interrupt: NOT IMPLEMENTED YET!!\n"); -#else unsigned long pld; unsigned int i; @@ -210,12 +207,7 @@ dp264_device_interrupt(unsigned long vector) isa_device_interrupt(vector); else handle_irq(16 + i); -#if 0 - TSUNAMI_cchip->dir0.csr = 1UL << i; mb(); - tmp = TSUNAMI_cchip->dir0.csr; -#endif } -#endif } static void -- cgit v1.2.3-70-g09d2 From 46931bf67c188d026879e943fa0426704991bed9 Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Thu, 21 Apr 2011 16:01:02 -0700 Subject: alpha: Force the user-visible HZ to a constant 1024. This kernel/user split was done long ago for other architectures. Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/include/asm/param.h | 8 +++++--- arch/alpha/include/uapi/asm/param.h | 7 ------- 2 files changed, 5 insertions(+), 10 deletions(-) (limited to 'arch') diff --git a/arch/alpha/include/asm/param.h b/arch/alpha/include/asm/param.h index bf46af51941..a5b68b268bc 100644 --- a/arch/alpha/include/asm/param.h +++ b/arch/alpha/include/asm/param.h @@ -3,7 +3,9 @@ #include -#define HZ CONFIG_HZ -#define USER_HZ HZ -# define CLOCKS_PER_SEC HZ /* frequency at which times() counts */ +# undef HZ +# define HZ CONFIG_HZ +# define USER_HZ 1024 +# define CLOCKS_PER_SEC USER_HZ /* frequency at which times() counts */ + #endif /* _ASM_ALPHA_PARAM_H */ diff --git a/arch/alpha/include/uapi/asm/param.h b/arch/alpha/include/uapi/asm/param.h index 29daed819eb..dbcd9834af6 100644 --- a/arch/alpha/include/uapi/asm/param.h +++ b/arch/alpha/include/uapi/asm/param.h @@ -1,13 +1,7 @@ #ifndef _UAPI_ASM_ALPHA_PARAM_H #define _UAPI_ASM_ALPHA_PARAM_H -/* ??? Gross. I don't want to parameterize this, and supposedly the - hardware ignores reprogramming. We also need userland buy-in to the - change in HZ, since this is visible in the wait4 resources etc. */ - -#ifndef __KERNEL__ #define HZ 1024 -#endif #define EXEC_PAGESIZE 8192 @@ -17,5 +11,4 @@ #define MAXHOSTNAMELEN 64 /* max length of hostname */ - #endif /* _UAPI_ASM_ALPHA_PARAM_H */ -- cgit v1.2.3-70-g09d2 From dff64649e757870e9351e7d85917ae681d20ee54 Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Fri, 19 Jul 2013 12:43:07 -0700 Subject: alpha: Use handle_percpu_irq for the timer interrupt Signed-off-by: Matt Turner Signed-off-by: Richard Henderson --- arch/alpha/kernel/irq_alpha.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/alpha/kernel/irq_alpha.c b/arch/alpha/kernel/irq_alpha.c index f433fc11877..28e4429596f 100644 --- a/arch/alpha/kernel/irq_alpha.c +++ b/arch/alpha/kernel/irq_alpha.c @@ -236,7 +236,7 @@ void __init init_rtc_irq(void) { irq_set_chip_and_handler_name(RTC_IRQ, &dummy_irq_chip, - handle_simple_irq, "RTC"); + handle_percpu_irq, "RTC"); setup_irq(RTC_IRQ, &timer_irqaction); } -- cgit v1.2.3-70-g09d2 From 9af588736f48401cca6a39a96a59fb994068237f Mon Sep 17 00:00:00 2001 From: Ulf Hansson Date: Mon, 27 May 2013 15:16:06 +0200 Subject: ARM: nomadik: Update MMC defconfigs Enable MMC_UNSAFE_RESUME to accomplish a proper suspend/resume cycle for SD/SDIO/(e)MMC. ARMMMCI host driver supports clock gating through runtime PM, thus MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which means we can explicity disable MMC_BLOCK_BOUNCE, since it's default enabled, to skip unnecessary bounce buffer copying. Signed-off-by: Ulf Hansson Signed-off-by: Linus Walleij --- arch/arm/configs/nhk8815_defconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/configs/nhk8815_defconfig b/arch/arm/configs/nhk8815_defconfig index 35f8cf299fa..b605575f322 100644 --- a/arch/arm/configs/nhk8815_defconfig +++ b/arch/arm/configs/nhk8815_defconfig @@ -95,7 +95,8 @@ CONFIG_I2C_NOMADIK=y CONFIG_DEBUG_GPIO=y # CONFIG_HWMON is not set CONFIG_MMC=y -CONFIG_MMC_CLKGATE=y +CONFIG_MMC_UNSAFE_RESUME=y +# CONFIG_MMC_BLOCK_BOUNCE is not set CONFIG_MMC_ARMMMCI=y CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y -- cgit v1.2.3-70-g09d2 From 931f57378631c19545ec933d2df0f4fb46d16659 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 28 May 2013 16:40:29 +0200 Subject: ARM: nomadik: update defconfig base Update the Nomadik defconfig enabling: - GPIO keyboard input - Regulators - LED class driver - LED heartbeat trigger Signed-off-by: Linus Walleij --- arch/arm/configs/nhk8815_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/configs/nhk8815_defconfig b/arch/arm/configs/nhk8815_defconfig index b605575f322..e4cb5a42042 100644 --- a/arch/arm/configs/nhk8815_defconfig +++ b/arch/arm/configs/nhk8815_defconfig @@ -48,7 +48,6 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_MTD=y CONFIG_MTD_TESTS=m CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_CHAR=y CONFIG_MTD_BLOCK=y CONFIG_MTD_NAND_ECC_SMC=y CONFIG_MTD_NAND=y @@ -94,6 +93,7 @@ CONFIG_I2C_GPIO=y CONFIG_I2C_NOMADIK=y CONFIG_DEBUG_GPIO=y # CONFIG_HWMON is not set +CONFIG_REGULATOR=y CONFIG_MMC=y CONFIG_MMC_UNSAFE_RESUME=y # CONFIG_MMC_BLOCK_BOUNCE is not set -- cgit v1.2.3-70-g09d2 From fec57e15527ab2e3d22cfbf04f2b98f823f294ff Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 20 Jun 2013 13:48:16 +0200 Subject: ARM: nomadik: configure for NO_HZ and HRTIMERS This enables tickless idle (NO_HZ_IDLE) and high resolution timers for the Nomadik. Signed-off-by: Linus Walleij --- arch/arm/configs/nhk8815_defconfig | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/configs/nhk8815_defconfig b/arch/arm/configs/nhk8815_defconfig index e4cb5a42042..263ae3869e3 100644 --- a/arch/arm/configs/nhk8815_defconfig +++ b/arch/arm/configs/nhk8815_defconfig @@ -1,6 +1,8 @@ # CONFIG_LOCALVERSION_AUTO is not set # CONFIG_SWAP is not set CONFIG_SYSVIPC=y +CONFIG_NO_HZ_IDLE=y +CONFIG_HIGH_RES_TIMERS=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 -- cgit v1.2.3-70-g09d2 From d58e9a02e1435744d80a99742d1135a6921318eb Mon Sep 17 00:00:00 2001 From: Qipan Li Date: Thu, 4 Jul 2013 15:55:26 +0800 Subject: pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl this patch adds the lost pin group which supports to let USP0 to simulate a UART without hardware flow control. Signed-off-by: Qipan Li Signed-off-by: Barry Song Signed-off-by: Linus Walleij --- arch/arm/boot/dts/atlas6.dtsi | 6 ++++++ drivers/pinctrl/sirf/pinctrl-atlas6.c | 20 ++++++++++++++++++++ 2 files changed, 26 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/atlas6.dtsi b/arch/arm/boot/dts/atlas6.dtsi index 9866cd736de..537041253db 100644 --- a/arch/arm/boot/dts/atlas6.dtsi +++ b/arch/arm/boot/dts/atlas6.dtsi @@ -485,6 +485,12 @@ sirf,function = "usp0"; }; }; + usp0_uart_nostreamctrl_pins_a: usp0@1 { + usp0 { + sirf,pins = "usp0_uart_nostreamctrl_grp"; + sirf,function = "usp0_uart_nostreamctrl"; + }; + }; usp1_pins_a: usp1@0 { usp1 { sirf,pins = "usp1grp"; diff --git a/drivers/pinctrl/sirf/pinctrl-atlas6.c b/drivers/pinctrl/sirf/pinctrl-atlas6.c index c641be9c5b8..867c9681763 100644 --- a/drivers/pinctrl/sirf/pinctrl-atlas6.c +++ b/drivers/pinctrl/sirf/pinctrl-atlas6.c @@ -509,6 +509,19 @@ static const struct sirfsoc_padmux usp0_padmux = { static const unsigned usp0_pins[] = { 51, 52, 53, 54, 55 }; +static const struct sirfsoc_muxmask usp0_uart_nostreamctrl_muxmask[] = { + { + .group = 1, + .mask = BIT(20) | BIT(21), + }, +}; + +static const struct sirfsoc_padmux usp0_uart_nostreamctrl_padmux = { + .muxmask_counts = ARRAY_SIZE(usp0_uart_nostreamctrl_muxmask), + .muxmask = usp0_uart_nostreamctrl_muxmask, +}; + +static const unsigned usp0_uart_nostreamctrl_pins[] = { 52, 53 }; static const struct sirfsoc_muxmask usp1_muxmask[] = { { .group = 0, @@ -822,6 +835,8 @@ static const struct sirfsoc_pin_group sirfsoc_pin_groups[] = { SIRFSOC_PIN_GROUP("uart2grp", uart2_pins), SIRFSOC_PIN_GROUP("uart2_nostreamctrlgrp", uart2_nostreamctrl_pins), SIRFSOC_PIN_GROUP("usp0grp", usp0_pins), + SIRFSOC_PIN_GROUP("usp0_uart_nostreamctrl_grp", + usp0_uart_nostreamctrl_pins), SIRFSOC_PIN_GROUP("usp1grp", usp1_pins), SIRFSOC_PIN_GROUP("i2c0grp", i2c0_pins), SIRFSOC_PIN_GROUP("i2c1grp", i2c1_pins), @@ -862,6 +877,8 @@ static const char * const uart0grp[] = { "uart0grp" }; static const char * const uart1grp[] = { "uart1grp" }; static const char * const uart2grp[] = { "uart2grp" }; static const char * const uart2_nostreamctrlgrp[] = { "uart2_nostreamctrlgrp" }; +static const char * const usp0_uart_nostreamctrl_grp[] = { + "usp0_uart_nostreamctrl_grp" }; static const char * const usp0grp[] = { "usp0grp" }; static const char * const usp1grp[] = { "usp1grp" }; static const char * const i2c0grp[] = { "i2c0grp" }; @@ -904,6 +921,9 @@ static const struct sirfsoc_pmx_func sirfsoc_pmx_functions[] = { SIRFSOC_PMX_FUNCTION("uart2", uart2grp, uart2_padmux), SIRFSOC_PMX_FUNCTION("uart2_nostreamctrl", uart2_nostreamctrlgrp, uart2_nostreamctrl_padmux), SIRFSOC_PMX_FUNCTION("usp0", usp0grp, usp0_padmux), + SIRFSOC_PMX_FUNCTION("usp0_uart_nostreamctrl", + usp0_uart_nostreamctrl_grp, + usp0_uart_nostreamctrl_padmux), SIRFSOC_PMX_FUNCTION("usp1", usp1grp, usp1_padmux), SIRFSOC_PMX_FUNCTION("i2c0", i2c0grp, i2c0_padmux), SIRFSOC_PMX_FUNCTION("i2c1", i2c1grp, i2c1_padmux), -- cgit v1.2.3-70-g09d2 From c8078de853d51e9b86a2f025ee281b5a81c80655 Mon Sep 17 00:00:00 2001 From: Barry Song Date: Thu, 4 Jul 2013 15:55:27 +0800 Subject: arm/dts: sirf: fix the pingroup name mismatch between drivers and dts in drivers/pinctrl/sirf, pingroup name is cko0 and cko1, but in dts, they are cko0 and cko1_rst. this patch fixes the error in dts. Signed-off-by: Barry Song Signed-off-by: Linus Walleij --- arch/arm/boot/dts/atlas6.dtsi | 16 ++++++++-------- arch/arm/boot/dts/prima2.dtsi | 16 ++++++++-------- 2 files changed, 16 insertions(+), 16 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/atlas6.dtsi b/arch/arm/boot/dts/atlas6.dtsi index 537041253db..a0f2721ea58 100644 --- a/arch/arm/boot/dts/atlas6.dtsi +++ b/arch/arm/boot/dts/atlas6.dtsi @@ -521,16 +521,16 @@ sirf,function = "pulse_count"; }; }; - cko0_rst_pins_a: cko0_rst@0 { - cko0_rst { - sirf,pins = "cko0_rstgrp"; - sirf,function = "cko0_rst"; + cko0_pins_a: cko0@0 { + cko0 { + sirf,pins = "cko0grp"; + sirf,function = "cko0"; }; }; - cko1_rst_pins_a: cko1_rst@0 { - cko1_rst { - sirf,pins = "cko1_rstgrp"; - sirf,function = "cko1_rst"; + cko1_pins_a: cko1@0 { + cko1 { + sirf,pins = "cko1grp"; + sirf,function = "cko1"; }; }; }; diff --git a/arch/arm/boot/dts/prima2.dtsi b/arch/arm/boot/dts/prima2.dtsi index 05e9489cf95..bbeb623fc2c 100644 --- a/arch/arm/boot/dts/prima2.dtsi +++ b/arch/arm/boot/dts/prima2.dtsi @@ -515,16 +515,16 @@ sirf,function = "pulse_count"; }; }; - cko0_rst_pins_a: cko0_rst@0 { - cko0_rst { - sirf,pins = "cko0_rstgrp"; - sirf,function = "cko0_rst"; + cko0_pins_a: cko0@0 { + cko0 { + sirf,pins = "cko0grp"; + sirf,function = "cko0"; }; }; - cko1_rst_pins_a: cko1_rst@0 { - cko1_rst { - sirf,pins = "cko1_rstgrp"; - sirf,function = "cko1_rst"; + cko1_pins_a: cko1@0 { + cko1 { + sirf,pins = "cko1grp"; + sirf,function = "cko1"; }; }; }; -- cgit v1.2.3-70-g09d2 From b6992fa9a74862c5addb62cde1657c7479615d86 Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 17 Jul 2013 17:54:27 +0100 Subject: ARM: document DEBUG_UNCOMPRESS Kconfig option This non-user visible option lacked any kind of documentation. This is quite common for non-user visible options; certian people can't understand the point of documenting such options with help text. However, here we have a case in point: developers don't understand the option either, as they were thinking that when the option is not set, the decompressor should produce no output what so ever. This is incorrect, as the purpose of this option is to control whether a multiplatform kernel uses the kernel debugging macros to produce output or not. So let's document this via help rather than commentry to prevent others falling into this misunderstanding. Signed-off-by: Russell King --- arch/arm/Kconfig.debug | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index e401a766c0b..583f4a00ec3 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -804,9 +804,19 @@ config DEBUG_LL_INCLUDE config DEBUG_UNCOMPRESS bool - default y if ARCH_MULTIPLATFORM && DEBUG_LL && \ - !DEBUG_OMAP2PLUS_UART && \ + depends on ARCH_MULTIPLATFORM + default y if DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \ !DEBUG_TEGRA_UART + help + This option influences the normal decompressor output for + multiplatform kernels. Normally, multiplatform kernels disable + decompressor output because it is not possible to know where to + send the decompressor output. + + When this option is set, the selected DEBUG_LL output method + will be re-used for normal decompressor output on multiplatform + kernels. + config UNCOMPRESS_INCLUDE string -- cgit v1.2.3-70-g09d2 From bf3f0f332f76a85ff3a0b393aaded5a8533769c0 Mon Sep 17 00:00:00 2001 From: Will Deacon Date: Mon, 15 Jul 2013 14:26:19 +0100 Subject: ARM: 7784/1: mm: ensure SMP alternates assemble to exactly 4 bytes with Thumb-2 Commit ae8a8b9553bd ("ARM: 7691/1: mm: kill unused TLB_CAN_READ_FROM_L1_CACHE and use ALT_SMP instead") added early function returns for page table cache flushing operations on ARMv7 SMP CPUs. Unfortunately, when targetting Thumb-2, these `mov pc, lr' sequences assemble to 2 bytes which can lead to corruption of the instruction stream after code patching. This patch fixes the alternates to use wide (32-bit) instructions for Thumb-2, therefore ensuring that the patching code works correctly. Cc: Signed-off-by: Will Deacon Signed-off-by: Russell King --- arch/arm/mm/proc-v7-2level.S | 2 +- arch/arm/mm/proc-v7-3level.S | 2 +- arch/arm/mm/proc-v7.S | 11 ++++++----- 3 files changed, 8 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/proc-v7-2level.S b/arch/arm/mm/proc-v7-2level.S index f64afb9f1bd..bdd3be4be77 100644 --- a/arch/arm/mm/proc-v7-2level.S +++ b/arch/arm/mm/proc-v7-2level.S @@ -110,7 +110,7 @@ ENTRY(cpu_v7_set_pte_ext) ARM( str r3, [r0, #2048]! ) THUMB( add r0, r0, #2048 ) THUMB( str r3, [r0] ) - ALT_SMP(mov pc,lr) + ALT_SMP(W(nop)) ALT_UP (mcr p15, 0, r0, c7, c10, 1) @ flush_pte #endif mov pc, lr diff --git a/arch/arm/mm/proc-v7-3level.S b/arch/arm/mm/proc-v7-3level.S index c36ac69488c..01a719e18bb 100644 --- a/arch/arm/mm/proc-v7-3level.S +++ b/arch/arm/mm/proc-v7-3level.S @@ -81,7 +81,7 @@ ENTRY(cpu_v7_set_pte_ext) tst r3, #1 << (55 - 32) @ L_PTE_DIRTY orreq r2, #L_PTE_RDONLY 1: strd r2, r3, [r0] - ALT_SMP(mov pc, lr) + ALT_SMP(W(nop)) ALT_UP (mcr p15, 0, r0, c7, c10, 1) @ flush_pte #endif mov pc, lr diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S index 5c6d5a3050e..73398bcf9bd 100644 --- a/arch/arm/mm/proc-v7.S +++ b/arch/arm/mm/proc-v7.S @@ -75,13 +75,14 @@ ENTRY(cpu_v7_do_idle) ENDPROC(cpu_v7_do_idle) ENTRY(cpu_v7_dcache_clean_area) - ALT_SMP(mov pc, lr) @ MP extensions imply L1 PTW - ALT_UP(W(nop)) - dcache_line_size r2, r3 -1: mcr p15, 0, r0, c7, c10, 1 @ clean D entry + ALT_SMP(W(nop)) @ MP extensions imply L1 PTW + ALT_UP_B(1f) + mov pc, lr +1: dcache_line_size r2, r3 +2: mcr p15, 0, r0, c7, c10, 1 @ clean D entry add r0, r0, r2 subs r1, r1, r2 - bhi 1b + bhi 2b dsb mov pc, lr ENDPROC(cpu_v7_dcache_clean_area) -- cgit v1.2.3-70-g09d2 From c65b7e98b4edce7faf534154b28eae8fb579144b Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 17 Jul 2013 17:53:04 +0100 Subject: ARM: 7785/1: mm: restrict early_alloc to section-aligned memory When map_lowmem() runs, and processes a memory bank whose start or end is not section-aligned, memory must be allocated to store the 2nd-level page tables. Those allocations are made by calling memblock_alloc(). At this point, the only memory that is free *and* mapped is memory which has already been mapped by map_lowmem() itself. For this reason, we must calculate the first point at which map_lowmem() will need to allocate memory, and set the memblock allocation limit to a lower address, so that memblock_alloc() is guaranteed to return memory that is already mapped. This patch enhances sanity_check_meminfo() to calculate that memory address, and pass it to memblock_set_current_limit(), rather than just assuming the limit is arm_lowmem_limit. The algorithm applied is: * Default memblock_limit to arm_lowmem_limit in the absence of any other limit; arm_lowmem_limit is the highest memory that is mapped by map_lowmem(). * While walking the list of memblocks, if the start of a block is not aligned, 2nd-level page tables will need to be allocated to map the first few pages of the block. Hence, the memblock_limit must be before the start of the block. * Similarly, if the end of any block is not aligned, 2nd-level page tables will need to be allocated to map the last few pages of the block. Hence, the memblock_limit must point at the end of the block, rounded down to section-alignment. * The memory blocks are assumed to be sorted in address order, so the first unaligned block start or end is used to set the limit. With this algorithm, the start or end of almost any bank can be non- section-aligned. The only exception is that the start of bank 0 must be section-aligned, since otherwise memory would need to be allocated when mapping the start of bank 0, which occurs before any free memory is mapped. [swarren, wrote commit description, rewrote calculation of memblock_limit] Signed-off-by: Stephen Warren Signed-off-by: Russell King --- arch/arm/mm/mmu.c | 43 ++++++++++++++++++++++++++++++++++++++----- 1 file changed, 38 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 4f56617a239..b3fdb63783e 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -989,6 +989,7 @@ phys_addr_t arm_lowmem_limit __initdata = 0; void __init sanity_check_meminfo(void) { + phys_addr_t memblock_limit = 0; int i, j, highmem = 0; phys_addr_t vmalloc_limit = __pa(vmalloc_min - 1) + 1; @@ -1052,9 +1053,32 @@ void __init sanity_check_meminfo(void) bank->size = size_limit; } #endif - if (!bank->highmem && bank->start + bank->size > arm_lowmem_limit) - arm_lowmem_limit = bank->start + bank->size; + if (!bank->highmem) { + phys_addr_t bank_end = bank->start + bank->size; + if (bank_end > arm_lowmem_limit) + arm_lowmem_limit = bank_end; + + /* + * Find the first non-section-aligned page, and point + * memblock_limit at it. This relies on rounding the + * limit down to be section-aligned, which happens at + * the end of this function. + * + * With this algorithm, the start or end of almost any + * bank can be non-section-aligned. The only exception + * is that the start of the bank 0 must be section- + * aligned, since otherwise memory would need to be + * allocated when mapping the start of bank 0, which + * occurs before any free memory is mapped. + */ + if (!memblock_limit) { + if (!IS_ALIGNED(bank->start, SECTION_SIZE)) + memblock_limit = bank->start; + else if (!IS_ALIGNED(bank_end, SECTION_SIZE)) + memblock_limit = bank_end; + } + } j++; } #ifdef CONFIG_HIGHMEM @@ -1079,7 +1103,18 @@ void __init sanity_check_meminfo(void) #endif meminfo.nr_banks = j; high_memory = __va(arm_lowmem_limit - 1) + 1; - memblock_set_current_limit(arm_lowmem_limit); + + /* + * Round the memblock limit down to a section size. This + * helps to ensure that we will allocate memory from the + * last full section, which should be mapped. + */ + if (memblock_limit) + memblock_limit = round_down(memblock_limit, SECTION_SIZE); + if (!memblock_limit) + memblock_limit = arm_lowmem_limit; + + memblock_set_current_limit(memblock_limit); } static inline void prepare_page_table(void) @@ -1276,8 +1311,6 @@ void __init paging_init(struct machine_desc *mdesc) { void *zero_page; - memblock_set_current_limit(arm_lowmem_limit); - build_mem_type_table(); prepare_page_table(); map_lowmem(); -- cgit v1.2.3-70-g09d2 From b60d5db690f72a7cfe5e39f191f0719a9ef3a096 Mon Sep 17 00:00:00 2001 From: Mark Rutland Date: Thu, 18 Jul 2013 17:20:32 +0100 Subject: ARM: 7786/1: hyp: fix macro parameterisation Currently, compare_cpu_mode_with_primary uses a mixture of macro arguments and hardcoded registers, and does so incorrectly, as it stores (__boot_cpu_mode_offset | BOOT_CPU_MODE_MISMATCH) to (__boot_cpu_mode + &__boot_cpu_mode_offset), which could corrupt an arbitrary portion of memory. This patch fixes up compare_cpu_mode_with_primary to use the macro arguments, correctly updating __boot_cpu_mode. Signed-off-by: Mark Rutland Acked-by: Dave Martin Acked-by: Marc Zyngier Cc: Christoffer Dall Signed-off-by: Russell King --- arch/arm/kernel/hyp-stub.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/hyp-stub.S b/arch/arm/kernel/hyp-stub.S index 4910232c483..797b1a6a490 100644 --- a/arch/arm/kernel/hyp-stub.S +++ b/arch/arm/kernel/hyp-stub.S @@ -56,8 +56,8 @@ ENTRY(__boot_cpu_mode) ldr \reg3, [\reg2] ldr \reg1, [\reg2, \reg3] cmp \mode, \reg1 @ matches primary CPU boot mode? - orrne r7, r7, #BOOT_CPU_MODE_MISMATCH - strne r7, [r5, r6] @ record what happened and give up + orrne \reg1, \reg1, #BOOT_CPU_MODE_MISMATCH + strne \reg1, [\reg2, \reg3] @ record what happened and give up .endm #else /* ZIMAGE */ -- cgit v1.2.3-70-g09d2 From ab8d46c0609843a83aef3f486365ca5e7c21d537 Mon Sep 17 00:00:00 2001 From: Tetsuyuki Kobayashi Date: Mon, 22 Jul 2013 14:58:17 +0100 Subject: ARM: 7788/1: elf: fix lpae hwcap feature reporting in proc/cpuinfo Commit a469abd0f868 ("ARM: elf: add new hwcap for identifying atomic ldrd/strd instructions") added a new hwcap to identify LPAE on CPUs which support it. Whilst the hwcap data is correct, the string reported in /proc/cpuinfo actually matches on HWCAP_VFPD32, which was missing an entry in the string table. This patch fixes this problem by adding a "vfpd32" string at the correct offset, preventing us from falsely advertising LPAE on CPUs which do not support it. [will: added commit message] Acked-by: Will Deacon Tested-by: Will Deacon Signed-off-by: Tetsuyuki Kobayashi Signed-off-by: Will Deacon Signed-off-by: Russell King --- arch/arm/kernel/setup.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index 63af9a7ae51..96286cb383b 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -971,6 +971,7 @@ static const char *hwcap_str[] = { "vfpv4", "idiva", "idivt", + "vfpd32", "lpae", NULL }; -- cgit v1.2.3-70-g09d2 From 334ab91d5818256befbf083755d0bb9e7dbd2325 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Tue, 9 Jul 2013 08:26:24 +0100 Subject: ARM: dts: STi: Fix pinconf setup for STiH416 serial2 This patch fixes a bug in pinctrl setup of serial2 device, Some of the pins in the pinctrl node of serial2 do not belong to that pin-controller. This patch divides them in the pins into there respective pin controller nodes. Without this patch serial on StiH416-B2000 Board will not work as it fails with: "st-pinctrl pin-controller-rear.3: failed to get pin(99) name st-pinctrl pin-controller-rear.3: maps: function serial2 group serial2-0 num 4 pinconfig core: failed to register map default (3): no group/pin given" Signed-off-by: Srinivas Kandagatla Signed-off-by: Olof Johansson --- arch/arm/boot/dts/stih416-pinctrl.dtsi | 10 +++++++++- arch/arm/boot/dts/stih416.dtsi | 2 +- 2 files changed, 10 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi index 957b21a71b4..0f246c97926 100644 --- a/arch/arm/boot/dts/stih416-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi @@ -166,6 +166,15 @@ reg = <0x9000 0x100>; st,bank-name = "PIO31"; }; + + serial2-oe { + pinctrl_serial2_oe: serial2-1 { + st,pins { + output-enable = <&PIO11 3 ALT2 OUT>; + }; + }; + }; + }; pin-controller-rear { @@ -218,7 +227,6 @@ st,pins { tx = <&PIO17 4 ALT2 OUT>; rx = <&PIO17 5 ALT2 IN>; - output-enable = <&PIO11 3 ALT2 OUT>; }; }; }; diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi index 3cecd9689a4..1a0326ea7d0 100644 --- a/arch/arm/boot/dts/stih416.dtsi +++ b/arch/arm/boot/dts/stih416.dtsi @@ -79,7 +79,7 @@ interrupts = <0 197 0>; clocks = <&CLK_S_ICN_REG_0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_serial2>; + pinctrl-0 = <&pinctrl_serial2 &pinctrl_serial2_oe>; }; /* SBC_UART1 */ -- cgit v1.2.3-70-g09d2 From c9250073cdd54339a320b78719761d3ea33714fe Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Tue, 9 Jul 2013 08:26:33 +0100 Subject: ARM: STi: Set correct ARM ERRATAs. Some of the ARM_ERRATA selection is not done in the initial SOC support patches. This patch selects 2 new ARM_ERRATA's and removes one which was actually fixed. Signed-off-by: Srinivas Kandagatla [olof: reorder new errata entries] Signed-off-by: Olof Johansson --- arch/arm/mach-sti/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-sti/Kconfig b/arch/arm/mach-sti/Kconfig index d04e3bfe191..835833e3c4f 100644 --- a/arch/arm/mach-sti/Kconfig +++ b/arch/arm/mach-sti/Kconfig @@ -11,8 +11,9 @@ menuconfig ARCH_STI select HAVE_SMP select HAVE_ARM_SCU if SMP select ARCH_REQUIRE_GPIOLIB - select ARM_ERRATA_720789 select ARM_ERRATA_754322 + select ARM_ERRATA_764369 + select ARM_ERRATA_775420 select PL310_ERRATA_753970 if CACHE_PL310 select PL310_ERRATA_769419 if CACHE_PL310 help -- cgit v1.2.3-70-g09d2 From 6287e7319870ec949fb809e4eb4154c2b05b221f Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 27 Jun 2013 22:42:36 -0400 Subject: ARM: footbridge: fix overlapping PCI mappings Commit 8ef6e6201b26cb9fde79c1baa08145af6aca2815 (ARM: footbridge: use fixed PCI i/o mapping) broke booting on my netwinder. Before that, everything boots fine. Since then, it crashes on boot. With earlyprintk, I see it BUG-ing like so: kernel BUG at lib/ioremap.c:27! Internal error: Oops - BUG: 0 [#1] ARM ... [] (ioremap_page_range+0x128/0x154) from [] (dc21285_setup+0xd0/0x114) [] (dc21285_setup+0xd0/0x114) from [] (pci_common_init+0xa0/0x298) [] (pci_common_init+0xa0/0x298) from [] (netwinder_pci_init+0xc/0x18) [] (netwinder_pci_init+0xc/0x18) from [] (do_one_initcall+0xb4/0x180) ... Russell points out it's because of overlapping PCI mappings that was added with the aforementioned commit. Rob thought the code would re-use the static mapping, but that turns out to not be the case and instead hits the BUG further down. After deleting this hunk as suggested by Russel, the system boots up fine again and all my PCI devices work (IDE, ethernet, the DC21285). Signed-off-by: Mike Frysinger Acked-by: Rob Herring Cc: stable@vger.kernel.org # v3.5+ Signed-off-by: Olof Johansson --- arch/arm/mach-footbridge/dc21285.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-footbridge/dc21285.c b/arch/arm/mach-footbridge/dc21285.c index a7cd2cf5e08..3490a24f969 100644 --- a/arch/arm/mach-footbridge/dc21285.c +++ b/arch/arm/mach-footbridge/dc21285.c @@ -276,8 +276,6 @@ int __init dc21285_setup(int nr, struct pci_sys_data *sys) sys->mem_offset = DC21285_PCI_MEM; - pci_ioremap_io(0, DC21285_PCI_IO); - pci_add_resource_offset(&sys->resources, &res[0], sys->mem_offset); pci_add_resource_offset(&sys->resources, &res[1], sys->mem_offset); -- cgit v1.2.3-70-g09d2 From e64bf95e68bf92e7f6d906da4715b937cec5646c Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Sun, 21 Jul 2013 14:53:37 -0500 Subject: ARM: highbank: Only touch common coherency control register fields Midway adds new register fields to the coherency control registers, so writing absolute values will break on Midway. Change the register accesses to only modify the necessary and common fields in order to support both Midway and Highbank. Signed-off-by: Rob Herring Signed-off-by: Olof Johansson --- arch/arm/mach-highbank/highbank.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c index dc5d6becd8c..88815795fe2 100644 --- a/arch/arm/mach-highbank/highbank.c +++ b/arch/arm/mach-highbank/highbank.c @@ -115,6 +115,7 @@ static int highbank_platform_notifier(struct notifier_block *nb, { struct resource *res; int reg = -1; + u32 val; struct device *dev = __dev; if (event != BUS_NOTIFY_ADD_DEVICE) @@ -141,10 +142,10 @@ static int highbank_platform_notifier(struct notifier_block *nb, return NOTIFY_DONE; if (of_property_read_bool(dev->of_node, "dma-coherent")) { - writel(0xff31, sregs_base + reg); + val = readl(sregs_base + reg); + writel(val | 0xff01, sregs_base + reg); set_dma_ops(dev, &arm_coherent_dma_ops); - } else - writel(0, sregs_base + reg); + } return NOTIFY_OK; } -- cgit v1.2.3-70-g09d2 From 803075dba31c17af110e1d9a915fe7262165b213 Mon Sep 17 00:00:00 2001 From: Neil Horman Date: Wed, 17 Jul 2013 07:13:59 -0400 Subject: x86/iommu/vt-d: Expand interrupt remapping quirk to cover x58 chipset Recently we added an early quirk to detect 5500/5520 chipsets with early revisions that had problems with irq draining with interrupt remapping enabled: commit 03bbcb2e7e292838bb0244f5a7816d194c911d62 Author: Neil Horman Date: Tue Apr 16 16:38:32 2013 -0400 iommu/vt-d: add quirk for broken interrupt remapping on 55XX chipsets It turns out this same problem is present in the intel X58 chipset as well. See errata 69 here: http://www.intel.com/content/www/us/en/chipsets/x58-express-specification-update.html This patch extends the pci early quirk so that the chip devices/revisions specified in the above update are also covered in the same way: Signed-off-by: Neil Horman Reviewed-by: Jan Beulich Acked-by: Donald Dutile Cc: Joerg Roedel Cc: Andrew Cooper Cc: Malcolm Crossley Cc: Prarit Bhargava Cc: Don Zickus Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1374059639-8631-1-git-send-email-nhorman@tuxdriver.com [ Small edits. ] Signed-off-by: Ingo Molnar --- arch/x86/kernel/early-quirks.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/early-quirks.c b/arch/x86/kernel/early-quirks.c index 94ab6b90dd3..63bdb29b254 100644 --- a/arch/x86/kernel/early-quirks.c +++ b/arch/x86/kernel/early-quirks.c @@ -196,15 +196,23 @@ static void __init ati_bugs_contd(int num, int slot, int func) static void __init intel_remapping_check(int num, int slot, int func) { u8 revision; + u16 device; + device = read_pci_config_16(num, slot, func, PCI_DEVICE_ID); revision = read_pci_config_byte(num, slot, func, PCI_REVISION_ID); /* - * Revision 0x13 of this chipset supports irq remapping - * but has an erratum that breaks its behavior, flag it as such + * Revision 13 of all triggering devices id in this quirk have + * a problem draining interrupts when irq remapping is enabled, + * and should be flagged as broken. Additionally revisions 0x12 + * and 0x22 of device id 0x3405 has this problem. */ if (revision == 0x13) set_irq_remapping_broken(); + else if ((device == 0x3405) && + ((revision == 0x12) || + (revision == 0x22))) + set_irq_remapping_broken(); } @@ -239,6 +247,8 @@ static struct chipset early_qrk[] __initdata = { PCI_CLASS_SERIAL_SMBUS, PCI_ANY_ID, 0, ati_bugs_contd }, { PCI_VENDOR_ID_INTEL, 0x3403, PCI_CLASS_BRIDGE_HOST, PCI_BASE_CLASS_BRIDGE, 0, intel_remapping_check }, + { PCI_VENDOR_ID_INTEL, 0x3405, PCI_CLASS_BRIDGE_HOST, + PCI_BASE_CLASS_BRIDGE, 0, intel_remapping_check }, { PCI_VENDOR_ID_INTEL, 0x3406, PCI_CLASS_BRIDGE_HOST, PCI_BASE_CLASS_BRIDGE, 0, intel_remapping_check }, {} -- cgit v1.2.3-70-g09d2 From 82b2f495fba338d1e3098dde1df54944a9c19751 Mon Sep 17 00:00:00 2001 From: Mark Rutland Date: Tue, 9 Jul 2013 15:16:06 +0100 Subject: arm64: virt: ensure visibility of __boot_cpu_mode Secondary CPUs write to __boot_cpu_mode with caches disabled, and thus a cached value of __boot_cpu_mode may be incoherent with that in memory. This could lead to a failure to detect mismatched boot modes. This patch adds flushing to ensure that writes by secondaries to __boot_cpu_mode are made visible before we test against it. Signed-off-by: Mark Rutland Cc: Marc Zyngier Cc: Christoffer Dall Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/virt.h | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'arch') diff --git a/arch/arm64/include/asm/virt.h b/arch/arm64/include/asm/virt.h index 439827271e3..26e310c5434 100644 --- a/arch/arm64/include/asm/virt.h +++ b/arch/arm64/include/asm/virt.h @@ -21,6 +21,7 @@ #define BOOT_CPU_MODE_EL2 (0x0e12b007) #ifndef __ASSEMBLY__ +#include /* * __boot_cpu_mode records what mode CPUs were booted in. @@ -36,9 +37,20 @@ extern u32 __boot_cpu_mode[2]; void __hyp_set_vectors(phys_addr_t phys_vector_base); phys_addr_t __hyp_get_vectors(void); +static inline void sync_boot_mode(void) +{ + /* + * As secondaries write to __boot_cpu_mode with caches disabled, we + * must flush the corresponding cache entries to ensure the visibility + * of their writes. + */ + __flush_dcache_area(__boot_cpu_mode, sizeof(__boot_cpu_mode)); +} + /* Reports the availability of HYP mode */ static inline bool is_hyp_mode_available(void) { + sync_boot_mode(); return (__boot_cpu_mode[0] == BOOT_CPU_MODE_EL2 && __boot_cpu_mode[1] == BOOT_CPU_MODE_EL2); } @@ -46,6 +58,7 @@ static inline bool is_hyp_mode_available(void) /* Check if the bootloader has booted CPUs in different modes */ static inline bool is_hyp_mode_mismatched(void) { + sync_boot_mode(); return __boot_cpu_mode[0] != __boot_cpu_mode[1]; } -- cgit v1.2.3-70-g09d2 From b0946fc84628b8d60e7a2034b48d1aff7da9d1df Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Tue, 23 Jul 2013 11:05:10 +0100 Subject: arm64: Fix definition of arm_pm_restart to match the declaration Commit ff70130 (arm64: use common reboot infrastructure) converted the arm_pm_restart declaration to the new reboot infrastructure but missed the actual definition. Signed-off-by: Catalin Marinas --- arch/arm64/kernel/process.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm64/kernel/process.c b/arch/arm64/kernel/process.c index 1788bf6b471..57fb55c44c9 100644 --- a/arch/arm64/kernel/process.c +++ b/arch/arm64/kernel/process.c @@ -81,7 +81,7 @@ void soft_restart(unsigned long addr) void (*pm_power_off)(void); EXPORT_SYMBOL_GPL(pm_power_off); -void (*arm_pm_restart)(char str, const char *cmd); +void (*arm_pm_restart)(enum reboot_mode reboot_mode, const char *cmd); EXPORT_SYMBOL_GPL(arm_pm_restart); void arch_cpu_idle_prepare(void) -- cgit v1.2.3-70-g09d2 From 2451ade070ef9b0a0f118ac41896da856e72b5a1 Mon Sep 17 00:00:00 2001 From: Stefano Stabellini Date: Sun, 21 Jul 2013 15:17:54 +0000 Subject: xen/arm,arm64: update xen_restart after ff701306cd49 and 7b6d864b48d9 Commit 7b6d864b48d9 (reboot: arm: change reboot_mode to use enum reboot_mode) and ff701306cd49 (arm64: use common reboot infrastructure) change the prototype of arm_pm_restart on arm and arm64. Update xen_restart accordingly. Signed-off-by: Stefano Stabellini --- arch/arm/xen/enlighten.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/xen/enlighten.c b/arch/arm/xen/enlighten.c index f71c37edca2..c9770ba5c7d 100644 --- a/arch/arm/xen/enlighten.c +++ b/arch/arm/xen/enlighten.c @@ -172,7 +172,7 @@ static void __init xen_percpu_init(void *unused) enable_percpu_irq(xen_events_irq, 0); } -static void xen_restart(char str, const char *cmd) +static void xen_restart(enum reboot_mode reboot_mode, const char *cmd) { struct sched_shutdown r = { .reason = SHUTDOWN_reboot }; int rc; -- cgit v1.2.3-70-g09d2 From ed882c3e72d6037589baa4328585c2b0450e673c Mon Sep 17 00:00:00 2001 From: Vincent Stehlé Date: Thu, 27 Jun 2013 14:49:27 +0200 Subject: ARM: keystone: fix compilation warning MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Fix the following compilation warning: arch/arm/mach-keystone/keystone.c:74:2: warning: initialization from incompatible pointer type [enabled by default] arch/arm/mach-keystone/keystone.c:74:2: warning: (near initialization for ‘__mach_desc_KEYSTONE.restart’) [enabled by default] Signed-off-by: Vincent Stehlé Cc: Robin Holt Cc: Russell King Cc: trivial@kernel.org Signed-off-by: Olof Johansson --- arch/arm/mach-keystone/keystone.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-keystone/keystone.c b/arch/arm/mach-keystone/keystone.c index fe4d9ff93a7..b661c5c2870 100644 --- a/arch/arm/mach-keystone/keystone.c +++ b/arch/arm/mach-keystone/keystone.c @@ -49,7 +49,7 @@ static const char *keystone_match[] __initconst = { NULL, }; -void keystone_restart(char mode, const char *cmd) +void keystone_restart(enum reboot_mode mode, const char *cmd) { u32 val; -- cgit v1.2.3-70-g09d2 From fe08bf9f46d6ae8e08de32d29234a2c928eebf8f Mon Sep 17 00:00:00 2001 From: Vincent Stehlé Date: Thu, 27 Jun 2013 14:42:41 +0200 Subject: ARM: zynq: fix compilation warning MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Fix the following compilation warning: arch/arm/mach-zynq/common.c:110:2: warning: initialization from incompatible pointer type [enabled by default] arch/arm/mach-zynq/common.c:110:2: warning: (near initialization for ‘__mach_desc_XILINX_EP107.restart’) [enabled by default] Signed-off-by: Vincent Stehlé Cc: Robin Holt Cc: Michal Simek Cc: Russell King Cc: trivial@kernel.org Signed-off-by: Olof Johansson --- arch/arm/mach-zynq/common.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-zynq/common.c b/arch/arm/mach-zynq/common.c index 5b799c29886..5f252569c68 100644 --- a/arch/arm/mach-zynq/common.c +++ b/arch/arm/mach-zynq/common.c @@ -91,7 +91,7 @@ static void __init zynq_map_io(void) zynq_scu_map_io(); } -static void zynq_system_reset(char mode, const char *cmd) +static void zynq_system_reset(enum reboot_mode mode, const char *cmd) { zynq_slcr_system_reset(); } -- cgit v1.2.3-70-g09d2 From a829abf8daa2dcf8223a9284b76d221e61130e13 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 5 Jul 2013 17:51:20 +0200 Subject: ARM: pxa: propagate errors from regulator_enable() to pxamci The em_x270_mci_setpower() and em_x270_usb_hub_init() functions call regulator_enable(), which may return an error that must be checked. This changes the em_x270_usb_hub_init() function to bail out if it fails, and changes the pxamci_platform_data->setpower callback so that the a failed em_x270_mci_setpower call can be propagated by the pxamci driver into the mmc core. Signed-off-by: Arnd Bergmann Cc: Mike Rapoport Cc: Paul Gortmaker Cc: Mark Brown Cc: Haojian Zhuang Acked-by: Chris Ball [olof: fixed order of regulator_enable() and test in em_x270_usb_hub_init] Signed-off-by: Olof Johansson --- arch/arm/mach-pxa/em-x270.c | 17 +++++++++++++---- arch/arm/mach-pxa/mainstone.c | 3 ++- arch/arm/mach-pxa/pcm990-baseboard.c | 3 ++- arch/arm/mach-pxa/poodle.c | 4 +++- arch/arm/mach-pxa/spitz.c | 4 +++- arch/arm/mach-pxa/stargate2.c | 3 ++- drivers/mmc/host/pxamci.c | 2 +- include/linux/platform_data/mmc-pxamci.h | 2 +- 8 files changed, 27 insertions(+), 11 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index f6726bb4eb9..3a3362fa793 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -477,16 +477,24 @@ static int em_x270_usb_hub_init(void) /* USB Hub power-on and reset */ gpio_direction_output(usb_hub_reset, 1); gpio_direction_output(GPIO9_USB_VBUS_EN, 0); - regulator_enable(em_x270_usb_ldo); + err = regulator_enable(em_x270_usb_ldo); + if (err) + goto err_free_rst_gpio; + gpio_set_value(usb_hub_reset, 0); gpio_set_value(usb_hub_reset, 1); regulator_disable(em_x270_usb_ldo); - regulator_enable(em_x270_usb_ldo); + err = regulator_enable(em_x270_usb_ldo); + if (err) + goto err_free_rst_gpio; + gpio_set_value(usb_hub_reset, 0); gpio_set_value(GPIO9_USB_VBUS_EN, 1); return 0; +err_free_rst_gpio: + gpio_free(usb_hub_reset); err_free_vbus_gpio: gpio_free(GPIO9_USB_VBUS_EN); err_free_usb_ldo: @@ -592,7 +600,7 @@ err_irq: return err; } -static void em_x270_mci_setpower(struct device *dev, unsigned int vdd) +static int em_x270_mci_setpower(struct device *dev, unsigned int vdd) { struct pxamci_platform_data* p_d = dev->platform_data; @@ -600,10 +608,11 @@ static void em_x270_mci_setpower(struct device *dev, unsigned int vdd) int vdd_uV = (2000 + (vdd - __ffs(MMC_VDD_20_21)) * 100) * 1000; regulator_set_voltage(em_x270_sdio_ldo, vdd_uV, vdd_uV); - regulator_enable(em_x270_sdio_ldo); + return regulator_enable(em_x270_sdio_ldo); } else { regulator_disable(em_x270_sdio_ldo); } + return 0; } static void em_x270_mci_exit(struct device *dev, void *data) diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c index d2c65231837..dd70343c870 100644 --- a/arch/arm/mach-pxa/mainstone.c +++ b/arch/arm/mach-pxa/mainstone.c @@ -408,7 +408,7 @@ static int mainstone_mci_init(struct device *dev, irq_handler_t mstone_detect_in return err; } -static void mainstone_mci_setpower(struct device *dev, unsigned int vdd) +static int mainstone_mci_setpower(struct device *dev, unsigned int vdd) { struct pxamci_platform_data* p_d = dev->platform_data; @@ -420,6 +420,7 @@ static void mainstone_mci_setpower(struct device *dev, unsigned int vdd) printk(KERN_DEBUG "%s: off\n", __func__); MST_MSCWR1 &= ~MST_MSCWR1_MMC_ON; } + return 0; } static void mainstone_mci_exit(struct device *dev, void *data) diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c index fb7f1d1627d..13e5b00eae9 100644 --- a/arch/arm/mach-pxa/pcm990-baseboard.c +++ b/arch/arm/mach-pxa/pcm990-baseboard.c @@ -335,7 +335,7 @@ static int pcm990_mci_init(struct device *dev, irq_handler_t mci_detect_int, return err; } -static void pcm990_mci_setpower(struct device *dev, unsigned int vdd) +static int pcm990_mci_setpower(struct device *dev, unsigned int vdd) { struct pxamci_platform_data *p_d = dev->platform_data; u8 val; @@ -348,6 +348,7 @@ static void pcm990_mci_setpower(struct device *dev, unsigned int vdd) val &= ~PCM990_CTRL_MMC2PWR; pcm990_cpld_writeb(PCM990_CTRL_MMC2PWR, PCM990_CTRL_REG5); + return 0; } static void pcm990_mci_exit(struct device *dev, void *data) diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c index 711d37e26bd..aedf053a1de 100644 --- a/arch/arm/mach-pxa/poodle.c +++ b/arch/arm/mach-pxa/poodle.c @@ -258,7 +258,7 @@ err_free_2: return err; } -static void poodle_mci_setpower(struct device *dev, unsigned int vdd) +static int poodle_mci_setpower(struct device *dev, unsigned int vdd) { struct pxamci_platform_data* p_d = dev->platform_data; @@ -270,6 +270,8 @@ static void poodle_mci_setpower(struct device *dev, unsigned int vdd) gpio_set_value(POODLE_GPIO_SD_PWR1, 0); gpio_set_value(POODLE_GPIO_SD_PWR, 0); } + + return 0; } static void poodle_mci_exit(struct device *dev, void *data) diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index 2125df0444e..4c29173026e 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -598,7 +598,7 @@ static inline void spitz_spi_init(void) {} * NOTE: The card detect interrupt isn't debounced so we delay it by 250ms to * give the card a chance to fully insert/eject. */ -static void spitz_mci_setpower(struct device *dev, unsigned int vdd) +static int spitz_mci_setpower(struct device *dev, unsigned int vdd) { struct pxamci_platform_data* p_d = dev->platform_data; @@ -606,6 +606,8 @@ static void spitz_mci_setpower(struct device *dev, unsigned int vdd) spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, SCOOP_CPR_SD_3V); else spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, 0x0); + + return 0; } static struct pxamci_platform_data spitz_mci_platform_data = { diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c index 88fde43c948..62aea3e835f 100644 --- a/arch/arm/mach-pxa/stargate2.c +++ b/arch/arm/mach-pxa/stargate2.c @@ -734,9 +734,10 @@ static int stargate2_mci_init(struct device *dev, * * Very simple control. Either it is on or off and is controlled by * a gpio pin */ -static void stargate2_mci_setpower(struct device *dev, unsigned int vdd) +static int stargate2_mci_setpower(struct device *dev, unsigned int vdd) { gpio_set_value(SG2_SD_POWER_ENABLE, !!vdd); + return 0; } static void stargate2_mci_exit(struct device *dev, void *data) diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c index 847b1996ce8..2c5a91bb8ec 100644 --- a/drivers/mmc/host/pxamci.c +++ b/drivers/mmc/host/pxamci.c @@ -128,7 +128,7 @@ static inline int pxamci_set_power(struct pxamci_host *host, !!on ^ host->pdata->gpio_power_invert); } if (!host->vcc && host->pdata && host->pdata->setpower) - host->pdata->setpower(mmc_dev(host->mmc), vdd); + return host->pdata->setpower(mmc_dev(host->mmc), vdd); return 0; } diff --git a/include/linux/platform_data/mmc-pxamci.h b/include/linux/platform_data/mmc-pxamci.h index 9eb515bb799..1706b3597ce 100644 --- a/include/linux/platform_data/mmc-pxamci.h +++ b/include/linux/platform_data/mmc-pxamci.h @@ -12,7 +12,7 @@ struct pxamci_platform_data { unsigned long detect_delay_ms; /* delay in millisecond before detecting cards after interrupt */ int (*init)(struct device *, irq_handler_t , void *); int (*get_ro)(struct device *); - void (*setpower)(struct device *, unsigned int); + int (*setpower)(struct device *, unsigned int); void (*exit)(struct device *, void *); int gpio_card_detect; /* gpio detecting card insertion */ int gpio_card_ro; /* gpio detecting read only toggle */ -- cgit v1.2.3-70-g09d2 From a520a9b7edc940fc735c526470313cf963fc72da Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Tue, 23 Jul 2013 14:02:06 -0300 Subject: ARM: multi_v7_defconfig: Select USB chipidea driver CONFIG_USB_EHCI_MXC selects the old i.mx USB driver, which does not support device tree. Select the USB chipidea driver instead, so that USB can be functional on i.mx. Signed-off-by: Fabio Estevam Signed-off-by: Olof Johansson --- arch/arm/configs/multi_v7_defconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index 120b08edb9a..6e572c64cf5 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -114,11 +114,12 @@ CONFIG_FB_SIMPLE=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_EHCI_HCD=y -CONFIG_USB_EHCI_MXC=y CONFIG_USB_EHCI_TEGRA=y CONFIG_USB_EHCI_HCD_PLATFORM=y CONFIG_USB_ISP1760_HCD=y CONFIG_USB_STORAGE=y +CONFIG_USB_CHIPIDEA=y +CONFIG_USB_CHIPIDEA_HOST=y CONFIG_AB8500_USB=y CONFIG_NOP_USB_XCEIV=y CONFIG_OMAP_USB2=y -- cgit v1.2.3-70-g09d2 From 33959f88fce9b8d3346d8000b3425814cbc6d6c0 Mon Sep 17 00:00:00 2001 From: Michael Neuling Date: Thu, 18 Jul 2013 11:31:51 +1000 Subject: powerpc: Add second POWER8 PVR entry POWER8 comes with two different PVRs. This patch enables the additional PVR in the cputable. The existing entry (PVR=0x4b) is renamed to POWER8E and the new entry (PVR=0x4d) is given POWER8. Signed-off-by: Michael Neuling Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/reg.h | 3 ++- arch/powerpc/kernel/cputable.c | 20 +++++++++++++++++++- arch/powerpc/kernel/prom_init.c | 5 +++-- 3 files changed, 24 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/reg.h b/arch/powerpc/include/asm/reg.h index 5d7d9c2a547..a6840e4e24f 100644 --- a/arch/powerpc/include/asm/reg.h +++ b/arch/powerpc/include/asm/reg.h @@ -1088,7 +1088,8 @@ #define PVR_970MP 0x0044 #define PVR_970GX 0x0045 #define PVR_POWER7p 0x004A -#define PVR_POWER8 0x004B +#define PVR_POWER8E 0x004B +#define PVR_POWER8 0x004D #define PVR_BE 0x0070 #define PVR_PA6T 0x0090 diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c index 2a45d0f0438..22973a74df7 100644 --- a/arch/powerpc/kernel/cputable.c +++ b/arch/powerpc/kernel/cputable.c @@ -494,9 +494,27 @@ static struct cpu_spec __initdata cpu_specs[] = { .cpu_restore = __restore_cpu_power7, .platform = "power7+", }, - { /* Power8 */ + { /* Power8E */ .pvr_mask = 0xffff0000, .pvr_value = 0x004b0000, + .cpu_name = "POWER8E (raw)", + .cpu_features = CPU_FTRS_POWER8, + .cpu_user_features = COMMON_USER_POWER8, + .cpu_user_features2 = COMMON_USER2_POWER8, + .mmu_features = MMU_FTRS_POWER8, + .icache_bsize = 128, + .dcache_bsize = 128, + .num_pmcs = 6, + .pmc_type = PPC_PMC_IBM, + .oprofile_cpu_type = "ppc64/power8", + .oprofile_type = PPC_OPROFILE_INVALID, + .cpu_setup = __setup_cpu_power8, + .cpu_restore = __restore_cpu_power8, + .platform = "power8", + }, + { /* Power8 */ + .pvr_mask = 0xffff0000, + .pvr_value = 0x004d0000, .cpu_name = "POWER8 (raw)", .cpu_features = CPU_FTRS_POWER8, .cpu_user_features = COMMON_USER_POWER8, diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c index 5eccda9fd33..607902424e7 100644 --- a/arch/powerpc/kernel/prom_init.c +++ b/arch/powerpc/kernel/prom_init.c @@ -644,7 +644,8 @@ unsigned char ibm_architecture_vec[] = { W(0xfffe0000), W(0x003a0000), /* POWER5/POWER5+ */ W(0xffff0000), W(0x003e0000), /* POWER6 */ W(0xffff0000), W(0x003f0000), /* POWER7 */ - W(0xffff0000), W(0x004b0000), /* POWER8 */ + W(0xffff0000), W(0x004b0000), /* POWER8E */ + W(0xffff0000), W(0x004d0000), /* POWER8 */ W(0xffffffff), W(0x0f000004), /* all 2.07-compliant */ W(0xffffffff), W(0x0f000003), /* all 2.06-compliant */ W(0xffffffff), W(0x0f000002), /* all 2.05-compliant */ @@ -706,7 +707,7 @@ unsigned char ibm_architecture_vec[] = { * must match by the macro below. Update the definition if * the structure layout changes. */ -#define IBM_ARCH_VEC_NRCORES_OFFSET 117 +#define IBM_ARCH_VEC_NRCORES_OFFSET 125 W(NR_CPUS), /* number of cores supported */ 0, 0, -- cgit v1.2.3-70-g09d2 From 0e0ed6406e61434d3f38fb58aa8464ec4722b77e Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Mon, 15 Jul 2013 14:04:50 +1000 Subject: powerpc/modules: Module CRC relocation fix causes perf issues Module CRCs are implemented as absolute symbols that get resolved by a linker script. We build an intermediate .o that contains an unresolved symbol for each CRC. genksysms parses this .o, calculates the CRCs and writes a linker script that "resolves" the symbols to the calculated CRC. Unfortunately the ppc64 relocatable kernel sees these CRCs as symbols that need relocating and relocates them at boot. Commit d4703aef (module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y) added a hook to reverse the bogus relocations. Part of this patch created a symbol at 0x0: # head -2 /proc/kallsyms 0000000000000000 T reloc_start c000000000000000 T .__start This reloc_start symbol is causing lots of confusion to perf. It thinks reloc_start is a massive function that stretches from 0x0 to 0xc000000000000000 and we get various cryptic errors out of perf, including: problem incrementing symbol count, skipping event This patch removes the reloc_start linker script label and instead defines it as PHYSICAL_START. We also need to wrap it with CONFIG_PPC64 because the ppc32 kernel can set a non zero PHYSICAL_START at compile time and we wouldn't want to subtract it from the CRCs in that case. Signed-off-by: Anton Blanchard Cc: Acked-by: Rusty Russell Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/module.h | 5 ++--- arch/powerpc/kernel/vmlinux.lds.S | 3 --- 2 files changed, 2 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/module.h b/arch/powerpc/include/asm/module.h index c1df590ec44..49fa55bfbac 100644 --- a/arch/powerpc/include/asm/module.h +++ b/arch/powerpc/include/asm/module.h @@ -82,10 +82,9 @@ struct exception_table_entry; void sort_ex_table(struct exception_table_entry *start, struct exception_table_entry *finish); -#ifdef CONFIG_MODVERSIONS +#if defined(CONFIG_MODVERSIONS) && defined(CONFIG_PPC64) #define ARCH_RELOCATES_KCRCTAB - -extern const unsigned long reloc_start[]; +#define reloc_start PHYSICAL_START #endif #endif /* __KERNEL__ */ #endif /* _ASM_POWERPC_MODULE_H */ diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S index 654e479802f..f096e72262f 100644 --- a/arch/powerpc/kernel/vmlinux.lds.S +++ b/arch/powerpc/kernel/vmlinux.lds.S @@ -38,9 +38,6 @@ jiffies = jiffies_64 + 4; #endif SECTIONS { - . = 0; - reloc_start = .; - . = KERNELBASE; /* -- cgit v1.2.3-70-g09d2 From 0b88f772bdf2847461debf417b1ee96043a7cb1b Mon Sep 17 00:00:00 2001 From: Tiejun Chen Date: Mon, 15 Jul 2013 10:36:04 +0800 Subject: powerpc: Access local paca after hard irq disabled In hard_irq_disable(), we accessed the PACA before we hard disabled the interrupts, potentially causing a warning as get_paca() will us debug_smp_processor_id(). Move that to after the disabling, and also use local_paca directly rather than get_paca() to avoid several redundant and useless checks. Signed-off-by: Tiejun Chen Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/hw_irq.h | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/hw_irq.h b/arch/powerpc/include/asm/hw_irq.h index ba713f166fa..10be1dd01c6 100644 --- a/arch/powerpc/include/asm/hw_irq.h +++ b/arch/powerpc/include/asm/hw_irq.h @@ -96,10 +96,11 @@ static inline bool arch_irqs_disabled(void) #endif #define hard_irq_disable() do { \ - u8 _was_enabled = get_paca()->soft_enabled; \ + u8 _was_enabled; \ __hard_irq_disable(); \ - get_paca()->soft_enabled = 0; \ - get_paca()->irq_happened |= PACA_IRQ_HARD_DIS; \ + _was_enabled = local_paca->soft_enabled; \ + local_paca->soft_enabled = 0; \ + local_paca->irq_happened |= PACA_IRQ_HARD_DIS; \ if (_was_enabled) \ trace_hardirqs_off(); \ } while(0) -- cgit v1.2.3-70-g09d2 From 97645154a9056106a957905c7836a016e5c89b3b Mon Sep 17 00:00:00 2001 From: Paul Bolle Date: Sun, 14 Jul 2013 13:02:15 +0200 Subject: powerpc/pseries: Drop "select HOTPLUG" The Kconfig symbol HOTPLUG was removed with commit 40b313608a ("Finally eradicate CONFIG_HOTPLUG"). But there's still one select statement for that symbol. It seems that select statement was added after the patch to remove CONFIG_HOTPLUG was submitted. Anyhow, it is useless and can be dropped. Signed-off-by: Paul Bolle Reviewed-by: Srivatsa S. Bhat Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/Kconfig | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/Kconfig b/arch/powerpc/platforms/pseries/Kconfig index 1bd3399146e..62b4f8025de 100644 --- a/arch/powerpc/platforms/pseries/Kconfig +++ b/arch/powerpc/platforms/pseries/Kconfig @@ -19,7 +19,6 @@ config PPC_PSERIES select ZLIB_DEFLATE select PPC_DOORBELL select HAVE_CONTEXT_TRACKING - select HOTPLUG if SMP select HOTPLUG_CPU if SMP default y -- cgit v1.2.3-70-g09d2 From 5d7ead0039b0c9500825b46997896352810efb0b Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Sat, 13 Jul 2013 12:53:40 +1000 Subject: powerpc/perf: Set PPC_FEATURE2_EBB when we register the power8 PMU The presence or absence of EBB is advertised to userspace via the presence or absence of PPC_FEATURE2_EBB in cpu_user_features2. Because the kernel can be built without PMU support, we should only add PPC_FEATURE2_EBB to cpu_user_features2 when we successfully register the power8 PMU support. Signed-off-by: Michael Ellerman Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/perf/power8-pmu.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/perf/power8-pmu.c b/arch/powerpc/perf/power8-pmu.c index 96a64d6a8bd..09def196f5c 100644 --- a/arch/powerpc/perf/power8-pmu.c +++ b/arch/powerpc/perf/power8-pmu.c @@ -621,10 +621,19 @@ static struct power_pmu power8_pmu = { static int __init init_power8_pmu(void) { + int rc; + if (!cur_cpu_spec->oprofile_cpu_type || strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power8")) return -ENODEV; - return register_power_pmu(&power8_pmu); + rc = register_power_pmu(&power8_pmu); + if (rc) + return rc; + + /* Tell userspace that EBB is supported */ + cur_cpu_spec->cpu_user_features2 |= PPC_FEATURE2_EBB; + + return 0; } early_initcall(init_power8_pmu); -- cgit v1.2.3-70-g09d2 From ee1dd1e3dc774cf257012215d996e8e7e370c162 Mon Sep 17 00:00:00 2001 From: Mahesh Salgaonkar Date: Wed, 10 Jul 2013 18:32:56 +0530 Subject: powerpc: Fix the corrupt r3 error during MCE handling. During Machine Check interrupt on pseries platform, R3 generally points to memory region inside RTAS (FWNMI) area. We see r3 corruption because when RTAS delivers the machine check exception it passes the address inside FWNMI area with the top most bit set. This patch fixes this issue by masking top two bit in machine check exception handler. Signed-off-by: Mahesh Salgaonkar Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/ras.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/ras.c b/arch/powerpc/platforms/pseries/ras.c index 7b3cbde8c78..721c0586b28 100644 --- a/arch/powerpc/platforms/pseries/ras.c +++ b/arch/powerpc/platforms/pseries/ras.c @@ -287,6 +287,9 @@ static struct rtas_error_log *fwnmi_get_errinfo(struct pt_regs *regs) unsigned long *savep; struct rtas_error_log *h, *errhdr = NULL; + /* Mask top two bits */ + regs->gpr[3] &= ~(0x3UL << 62); + if (!VALID_FWNMI_BUFFER(regs->gpr[3])) { printk(KERN_ERR "FWNMI: corrupt r3 0x%016lx\n", regs->gpr[3]); return NULL; -- cgit v1.2.3-70-g09d2 From 0ba178888b05a4efdaca7da528c170bd09f9687b Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:24:51 +0800 Subject: powerpc/eeh: Remove reference to PCI device We will rely on pcibios_release_device() to remove the EEH cache and unbind EEH device for the specific PCI device. So we shouldn't hold the reference to the PCI device from EEH cache and EEH device. Otherwise, pcibios_release_device() won't be called as we expected. The patch removes the reference to the PCI device in EEH core. Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/eeh.c | 4 ---- arch/powerpc/kernel/eeh_cache.c | 18 +++++------------- 2 files changed, 5 insertions(+), 17 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/eeh.c b/arch/powerpc/kernel/eeh.c index 39954fe941b..b5c425ea297 100644 --- a/arch/powerpc/kernel/eeh.c +++ b/arch/powerpc/kernel/eeh.c @@ -499,8 +499,6 @@ unsigned long eeh_check_failure(const volatile void __iomem *token, unsigned lon } eeh_dev_check_failure(edev); - - pci_dev_put(eeh_dev_to_pci_dev(edev)); return val; } @@ -904,7 +902,6 @@ static void eeh_add_device_late(struct pci_dev *dev) } WARN_ON(edev->pdev); - pci_dev_get(dev); edev->pdev = dev; dev->dev.archdata.edev = edev; @@ -992,7 +989,6 @@ static void eeh_remove_device(struct pci_dev *dev, int purge_pe) } edev->pdev = NULL; dev->dev.archdata.edev = NULL; - pci_dev_put(dev); eeh_rmv_from_parent_pe(edev, purge_pe); eeh_addr_cache_rmv_dev(dev); diff --git a/arch/powerpc/kernel/eeh_cache.c b/arch/powerpc/kernel/eeh_cache.c index f9ac1232a74..e8c9fd546a5 100644 --- a/arch/powerpc/kernel/eeh_cache.c +++ b/arch/powerpc/kernel/eeh_cache.c @@ -68,16 +68,12 @@ static inline struct eeh_dev *__eeh_addr_cache_get_device(unsigned long addr) struct pci_io_addr_range *piar; piar = rb_entry(n, struct pci_io_addr_range, rb_node); - if (addr < piar->addr_lo) { + if (addr < piar->addr_lo) n = n->rb_left; - } else { - if (addr > piar->addr_hi) { - n = n->rb_right; - } else { - pci_dev_get(piar->pcidev); - return piar->edev; - } - } + else if (addr > piar->addr_hi) + n = n->rb_right; + else + return piar->edev; } return NULL; @@ -156,7 +152,6 @@ eeh_addr_cache_insert(struct pci_dev *dev, unsigned long alo, if (!piar) return NULL; - pci_dev_get(dev); piar->addr_lo = alo; piar->addr_hi = ahi; piar->edev = pci_dev_to_eeh_dev(dev); @@ -250,7 +245,6 @@ restart: if (piar->pcidev == dev) { rb_erase(n, &pci_io_addr_cache_root.rb_root); - pci_dev_put(piar->pcidev); kfree(piar); goto restart; } @@ -302,12 +296,10 @@ void eeh_addr_cache_build(void) if (!edev) continue; - pci_dev_get(dev); /* matching put is in eeh_remove_device() */ dev->dev.archdata.edev = edev; edev->pdev = dev; eeh_addr_cache_insert_dev(dev); - eeh_sysfs_add_device(dev); } -- cgit v1.2.3-70-g09d2 From f2856491d24044de08da9e53cf7068841a8b4e1c Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:24:52 +0800 Subject: powerpc/eeh: Export functions for hotplug Make some functions public in order to support hotplug on either specific PCI bus or PCI device in future. Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/eeh.h | 9 +++++++++ arch/powerpc/kernel/eeh.c | 6 +++--- 2 files changed, 12 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/eeh.h b/arch/powerpc/include/asm/eeh.h index 09a8743143f..d9d35c27de2 100644 --- a/arch/powerpc/include/asm/eeh.h +++ b/arch/powerpc/include/asm/eeh.h @@ -209,9 +209,12 @@ unsigned long eeh_check_failure(const volatile void __iomem *token, unsigned long val); int eeh_dev_check_failure(struct eeh_dev *edev); void eeh_addr_cache_build(void); +void eeh_add_device_early(struct device_node *); void eeh_add_device_tree_early(struct device_node *); +void eeh_add_device_late(struct pci_dev *); void eeh_add_device_tree_late(struct pci_bus *); void eeh_add_sysfs_files(struct pci_bus *); +void eeh_remove_device(struct pci_dev *, int); void eeh_remove_bus_device(struct pci_dev *, int); /** @@ -252,12 +255,18 @@ static inline unsigned long eeh_check_failure(const volatile void __iomem *token static inline void eeh_addr_cache_build(void) { } +static inline void eeh_add_device_early(struct device_node *dn) { } + static inline void eeh_add_device_tree_early(struct device_node *dn) { } +static inline void eeh_add_device_late(struct pci_dev *dev) { } + static inline void eeh_add_device_tree_late(struct pci_bus *bus) { } static inline void eeh_add_sysfs_files(struct pci_bus *bus) { } +static inline void eeh_remove_device(struct pci_dev *dev, int purge_pe) { } + static inline void eeh_remove_bus_device(struct pci_dev *dev, int purge_pe) { } #define EEH_POSSIBLE_ERROR(val, type) (0) diff --git a/arch/powerpc/kernel/eeh.c b/arch/powerpc/kernel/eeh.c index b5c425ea297..582ad1ef46a 100644 --- a/arch/powerpc/kernel/eeh.c +++ b/arch/powerpc/kernel/eeh.c @@ -836,7 +836,7 @@ core_initcall_sync(eeh_init); * on the CEC architecture, type of the device, on earlier boot * command-line arguments & etc. */ -static void eeh_add_device_early(struct device_node *dn) +void eeh_add_device_early(struct device_node *dn) { struct pci_controller *phb; @@ -884,7 +884,7 @@ EXPORT_SYMBOL_GPL(eeh_add_device_tree_early); * This routine must be used to complete EEH initialization for PCI * devices that were added after system boot (e.g. hotplug, dlpar). */ -static void eeh_add_device_late(struct pci_dev *dev) +void eeh_add_device_late(struct pci_dev *dev) { struct device_node *dn; struct eeh_dev *edev; @@ -972,7 +972,7 @@ EXPORT_SYMBOL_GPL(eeh_add_sysfs_files); * this device will no longer be detected after this call; thus, * i/o errors affecting this slot may leave this device unusable. */ -static void eeh_remove_device(struct pci_dev *dev, int purge_pe) +void eeh_remove_device(struct pci_dev *dev, int purge_pe) { struct eeh_dev *edev; -- cgit v1.2.3-70-g09d2 From 008a4938ea07db071f03adffaa3a78c2fbbcde6b Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:24:53 +0800 Subject: powerpc/pci: Override pcibios_release_device() The patch overrides pcibios_release_device() to release EEH resources (EEH cache, unbinding EEH device) for the indicated PCI device. Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/pci-hotplug.c | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/kernel/pci-hotplug.c b/arch/powerpc/kernel/pci-hotplug.c index 3f608800c06..3dab2f2801b 100644 --- a/arch/powerpc/kernel/pci-hotplug.c +++ b/arch/powerpc/kernel/pci-hotplug.c @@ -21,6 +21,17 @@ #include #include +/** + * pcibios_release_device - release PCI device + * @dev: PCI device + * + * The function is called before releasing the indicated PCI device. + */ +void pcibios_release_device(struct pci_dev *dev) +{ + eeh_remove_device(dev, 1); +} + /** * __pcibios_remove_pci_devices - remove all devices under this bus * @bus: the indicated PCI bus -- cgit v1.2.3-70-g09d2 From 807a827d4e7455a40e8f56ec2a67c57a91cab9f7 Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:24:55 +0800 Subject: powerpc/eeh: Keep PE during hotplug When we do normal hotplug, the PE (shadow EEH structure) shouldn't be kept around. However, we need to keep it if the hotplug an artifial one caused by EEH errors recovery. Since we remove EEH device through the PCI hook pcibios_release_device(), the flag "purge_pe" passed to various functions is meaningless. So the patch removes the meaningless flag and introduce new flag "EEH_PE_KEEP" to save the PE while doing hotplug during EEH error recovery. Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/eeh.h | 11 +++++------ arch/powerpc/include/asm/pci-bridge.h | 1 - arch/powerpc/kernel/eeh.c | 28 ++-------------------------- arch/powerpc/kernel/eeh_driver.c | 7 +++++-- arch/powerpc/kernel/eeh_pe.c | 7 +++---- arch/powerpc/kernel/pci-hotplug.c | 26 +++++--------------------- 6 files changed, 20 insertions(+), 60 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/eeh.h b/arch/powerpc/include/asm/eeh.h index d9d35c27de2..2ce22d7b71a 100644 --- a/arch/powerpc/include/asm/eeh.h +++ b/arch/powerpc/include/asm/eeh.h @@ -55,6 +55,8 @@ struct device_node; #define EEH_PE_RECOVERING (1 << 1) /* Recovering PE */ #define EEH_PE_PHB_DEAD (1 << 2) /* Dead PHB */ +#define EEH_PE_KEEP (1 << 8) /* Keep PE on hotplug */ + struct eeh_pe { int type; /* PE type: PHB/Bus/Device */ int state; /* PE EEH dependent mode */ @@ -193,7 +195,7 @@ int eeh_phb_pe_create(struct pci_controller *phb); struct eeh_pe *eeh_phb_pe_get(struct pci_controller *phb); struct eeh_pe *eeh_pe_get(struct eeh_dev *edev); int eeh_add_to_parent_pe(struct eeh_dev *edev); -int eeh_rmv_from_parent_pe(struct eeh_dev *edev, int purge_pe); +int eeh_rmv_from_parent_pe(struct eeh_dev *edev); void eeh_pe_update_time_stamp(struct eeh_pe *pe); void *eeh_pe_dev_traverse(struct eeh_pe *root, eeh_traverse_func fn, void *flag); @@ -214,8 +216,7 @@ void eeh_add_device_tree_early(struct device_node *); void eeh_add_device_late(struct pci_dev *); void eeh_add_device_tree_late(struct pci_bus *); void eeh_add_sysfs_files(struct pci_bus *); -void eeh_remove_device(struct pci_dev *, int); -void eeh_remove_bus_device(struct pci_dev *, int); +void eeh_remove_device(struct pci_dev *); /** * EEH_POSSIBLE_ERROR() -- test for possible MMIO failure. @@ -265,9 +266,7 @@ static inline void eeh_add_device_tree_late(struct pci_bus *bus) { } static inline void eeh_add_sysfs_files(struct pci_bus *bus) { } -static inline void eeh_remove_device(struct pci_dev *dev, int purge_pe) { } - -static inline void eeh_remove_bus_device(struct pci_dev *dev, int purge_pe) { } +static inline void eeh_remove_device(struct pci_dev *dev) { } #define EEH_POSSIBLE_ERROR(val, type) (0) #define EEH_IO_ERROR_VALUE(size) (-1UL) diff --git a/arch/powerpc/include/asm/pci-bridge.h b/arch/powerpc/include/asm/pci-bridge.h index 2c1d8cb9b26..32d0d2018fa 100644 --- a/arch/powerpc/include/asm/pci-bridge.h +++ b/arch/powerpc/include/asm/pci-bridge.h @@ -209,7 +209,6 @@ static inline struct eeh_dev *of_node_to_eeh_dev(struct device_node *dn) extern struct pci_bus *pcibios_find_pci_bus(struct device_node *dn); /** Remove all of the PCI devices under this bus */ -extern void __pcibios_remove_pci_devices(struct pci_bus *bus, int purge_pe); extern void pcibios_remove_pci_devices(struct pci_bus *bus); /** Discover new pci devices under this bus, and add them */ diff --git a/arch/powerpc/kernel/eeh.c b/arch/powerpc/kernel/eeh.c index 582ad1ef46a..ce81477316b 100644 --- a/arch/powerpc/kernel/eeh.c +++ b/arch/powerpc/kernel/eeh.c @@ -964,7 +964,6 @@ EXPORT_SYMBOL_GPL(eeh_add_sysfs_files); /** * eeh_remove_device - Undo EEH setup for the indicated pci device * @dev: pci device to be removed - * @purge_pe: remove the PE or not * * This routine should be called when a device is removed from * a running system (e.g. by hotplug or dlpar). It unregisters @@ -972,7 +971,7 @@ EXPORT_SYMBOL_GPL(eeh_add_sysfs_files); * this device will no longer be detected after this call; thus, * i/o errors affecting this slot may leave this device unusable. */ -void eeh_remove_device(struct pci_dev *dev, int purge_pe) +void eeh_remove_device(struct pci_dev *dev) { struct eeh_dev *edev; @@ -990,34 +989,11 @@ void eeh_remove_device(struct pci_dev *dev, int purge_pe) edev->pdev = NULL; dev->dev.archdata.edev = NULL; - eeh_rmv_from_parent_pe(edev, purge_pe); + eeh_rmv_from_parent_pe(edev); eeh_addr_cache_rmv_dev(dev); eeh_sysfs_remove_device(dev); } -/** - * eeh_remove_bus_device - Undo EEH setup for the indicated PCI device - * @dev: PCI device - * @purge_pe: remove the corresponding PE or not - * - * This routine must be called when a device is removed from the - * running system through hotplug or dlpar. The corresponding - * PCI address cache will be removed. - */ -void eeh_remove_bus_device(struct pci_dev *dev, int purge_pe) -{ - struct pci_bus *bus = dev->subordinate; - struct pci_dev *child, *tmp; - - eeh_remove_device(dev, purge_pe); - - if (bus && dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) { - list_for_each_entry_safe(child, tmp, &bus->devices, bus_list) - eeh_remove_bus_device(child, purge_pe); - } -} -EXPORT_SYMBOL_GPL(eeh_remove_bus_device); - static int proc_eeh_show(struct seq_file *m, void *v) { if (0 == eeh_subsystem_enabled) { diff --git a/arch/powerpc/kernel/eeh_driver.c b/arch/powerpc/kernel/eeh_driver.c index 2b1ce17cae5..9ef3bbb8580 100644 --- a/arch/powerpc/kernel/eeh_driver.c +++ b/arch/powerpc/kernel/eeh_driver.c @@ -362,8 +362,10 @@ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus) * devices are expected to be attached soon when calling * into pcibios_add_pci_devices(). */ - if (bus) - __pcibios_remove_pci_devices(bus, 0); + if (bus) { + eeh_pe_state_mark(pe, EEH_PE_KEEP); + pcibios_remove_pci_devices(bus); + } /* Reset the pci controller. (Asserts RST#; resets config space). * Reconfigure bridges and devices. Don't try to bring the system @@ -386,6 +388,7 @@ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus) if (bus) { ssleep(5); pcibios_add_pci_devices(bus); + eeh_pe_state_clear(pe, EEH_PE_KEEP); } pe->tstamp = tstamp; diff --git a/arch/powerpc/kernel/eeh_pe.c b/arch/powerpc/kernel/eeh_pe.c index 016588a6f5e..32ef40940ba 100644 --- a/arch/powerpc/kernel/eeh_pe.c +++ b/arch/powerpc/kernel/eeh_pe.c @@ -333,7 +333,7 @@ int eeh_add_to_parent_pe(struct eeh_dev *edev) while (parent) { if (!(parent->type & EEH_PE_INVALID)) break; - parent->type &= ~EEH_PE_INVALID; + parent->type &= ~(EEH_PE_INVALID | EEH_PE_KEEP); parent = parent->parent; } pr_debug("EEH: Add %s to Device PE#%x, Parent PE#%x\n", @@ -397,14 +397,13 @@ int eeh_add_to_parent_pe(struct eeh_dev *edev) /** * eeh_rmv_from_parent_pe - Remove one EEH device from the associated PE * @edev: EEH device - * @purge_pe: remove PE or not * * The PE hierarchy tree might be changed when doing PCI hotplug. * Also, the PCI devices or buses could be removed from the system * during EEH recovery. So we have to call the function remove the * corresponding PE accordingly if necessary. */ -int eeh_rmv_from_parent_pe(struct eeh_dev *edev, int purge_pe) +int eeh_rmv_from_parent_pe(struct eeh_dev *edev) { struct eeh_pe *pe, *parent, *child; int cnt; @@ -431,7 +430,7 @@ int eeh_rmv_from_parent_pe(struct eeh_dev *edev, int purge_pe) if (pe->type & EEH_PE_PHB) break; - if (purge_pe) { + if (!(pe->state & EEH_PE_KEEP)) { if (list_empty(&pe->edevs) && list_empty(&pe->child_list)) { list_del(&pe->child); diff --git a/arch/powerpc/kernel/pci-hotplug.c b/arch/powerpc/kernel/pci-hotplug.c index 3dab2f2801b..fc0831d4971 100644 --- a/arch/powerpc/kernel/pci-hotplug.c +++ b/arch/powerpc/kernel/pci-hotplug.c @@ -29,49 +29,33 @@ */ void pcibios_release_device(struct pci_dev *dev) { - eeh_remove_device(dev, 1); + eeh_remove_device(dev); } /** - * __pcibios_remove_pci_devices - remove all devices under this bus + * pcibios_remove_pci_devices - remove all devices under this bus * @bus: the indicated PCI bus - * @purge_pe: destroy the PE on removal of PCI devices * * Remove all of the PCI devices under this bus both from the * linux pci device tree, and from the powerpc EEH address cache. - * By default, the corresponding PE will be destroied during the - * normal PCI hotplug path. For PCI hotplug during EEH recovery, - * the corresponding PE won't be destroied and deallocated. */ -void __pcibios_remove_pci_devices(struct pci_bus *bus, int purge_pe) +void pcibios_remove_pci_devices(struct pci_bus *bus) { struct pci_dev *dev, *tmp; struct pci_bus *child_bus; /* First go down child busses */ list_for_each_entry(child_bus, &bus->children, node) - __pcibios_remove_pci_devices(child_bus, purge_pe); + pcibios_remove_pci_devices(child_bus); pr_debug("PCI: Removing devices on bus %04x:%02x\n", pci_domain_nr(bus), bus->number); list_for_each_entry_safe(dev, tmp, &bus->devices, bus_list) { - pr_debug(" * Removing %s...\n", pci_name(dev)); - eeh_remove_bus_device(dev, purge_pe); + pr_debug(" Removing %s...\n", pci_name(dev)); pci_stop_and_remove_bus_device(dev); } } -/** - * pcibios_remove_pci_devices - remove all devices under this bus - * @bus: the indicated PCI bus - * - * Remove all of the PCI devices under this bus both from the - * linux pci device tree, and from the powerpc EEH address cache. - */ -void pcibios_remove_pci_devices(struct pci_bus *bus) -{ - __pcibios_remove_pci_devices(bus, 1); -} EXPORT_SYMBOL_GPL(pcibios_remove_pci_devices); /** -- cgit v1.2.3-70-g09d2 From 9feed42e93d2625db86423cedf8b4b2bed00779e Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:24:56 +0800 Subject: powerpc/eeh: Use safe list traversal when walking EEH devices Currently, we're trasversing the EEH devices list using list_for_each_entry(). That's not safe enough because the EEH devices might be removed from its parent PE while doing iteration. The patch replaces that with list_for_each_entry_safe(). Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/eeh.h | 4 ++-- arch/powerpc/kernel/eeh.c | 4 ++-- arch/powerpc/kernel/eeh_pe.c | 10 +++++----- 3 files changed, 9 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/eeh.h b/arch/powerpc/include/asm/eeh.h index 2ce22d7b71a..e8c411b63ca 100644 --- a/arch/powerpc/include/asm/eeh.h +++ b/arch/powerpc/include/asm/eeh.h @@ -74,8 +74,8 @@ struct eeh_pe { struct list_head child; /* Child PEs */ }; -#define eeh_pe_for_each_dev(pe, edev) \ - list_for_each_entry(edev, &pe->edevs, list) +#define eeh_pe_for_each_dev(pe, edev, tmp) \ + list_for_each_entry_safe(edev, tmp, &pe->edevs, list) /* * The struct is used to trace EEH state for the associated diff --git a/arch/powerpc/kernel/eeh.c b/arch/powerpc/kernel/eeh.c index ce81477316b..56bd4584f61 100644 --- a/arch/powerpc/kernel/eeh.c +++ b/arch/powerpc/kernel/eeh.c @@ -231,7 +231,7 @@ static size_t eeh_gather_pci_data(struct eeh_dev *edev, char * buf, size_t len) void eeh_slot_error_detail(struct eeh_pe *pe, int severity) { size_t loglen = 0; - struct eeh_dev *edev; + struct eeh_dev *edev, *tmp; bool valid_cfg_log = true; /* @@ -251,7 +251,7 @@ void eeh_slot_error_detail(struct eeh_pe *pe, int severity) eeh_pe_restore_bars(pe); pci_regs_buf[0] = 0; - eeh_pe_for_each_dev(pe, edev) { + eeh_pe_for_each_dev(pe, edev, tmp) { loglen += eeh_gather_pci_data(edev, pci_regs_buf + loglen, EEH_PCI_REGS_LOG_LEN - loglen); } diff --git a/arch/powerpc/kernel/eeh_pe.c b/arch/powerpc/kernel/eeh_pe.c index 32ef40940ba..c8b815e45c8 100644 --- a/arch/powerpc/kernel/eeh_pe.c +++ b/arch/powerpc/kernel/eeh_pe.c @@ -176,7 +176,7 @@ void *eeh_pe_dev_traverse(struct eeh_pe *root, eeh_traverse_func fn, void *flag) { struct eeh_pe *pe; - struct eeh_dev *edev; + struct eeh_dev *edev, *tmp; void *ret; if (!root) { @@ -186,7 +186,7 @@ void *eeh_pe_dev_traverse(struct eeh_pe *root, /* Traverse root PE */ for (pe = root; pe; pe = eeh_pe_next(pe, root)) { - eeh_pe_for_each_dev(pe, edev) { + eeh_pe_for_each_dev(pe, edev, tmp) { ret = fn(edev, flag); if (ret) return ret; @@ -501,7 +501,7 @@ static void *__eeh_pe_state_mark(void *data, void *flag) { struct eeh_pe *pe = (struct eeh_pe *)data; int state = *((int *)flag); - struct eeh_dev *tmp; + struct eeh_dev *edev, *tmp; struct pci_dev *pdev; /* @@ -511,8 +511,8 @@ static void *__eeh_pe_state_mark(void *data, void *flag) * the PCI device driver. */ pe->state |= state; - eeh_pe_for_each_dev(pe, tmp) { - pdev = eeh_dev_to_pci_dev(tmp); + eeh_pe_for_each_dev(pe, edev, tmp) { + pdev = eeh_dev_to_pci_dev(edev); if (pdev) pdev->error_state = pci_channel_io_frozen; } -- cgit v1.2.3-70-g09d2 From ab444ec97e8bd65fff9d489b9a409fc03979268b Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:24:57 +0800 Subject: powerpc/pci: Partial tree hotplug support When EEH error happens to one specific PE, the device drivers of its attached EEH devices (PCI devices) are checked to see the further action: reset with complete hotplug, or reset without hotplug. However, that's not enough for those PCI devices whose drivers can't support EEH, or those PCI devices without driver. So we need do so-called "partial hotplug" on basis of PCI devices. In the situation, part of PCI devices of the specific PE are unplugged and plugged again after PE reset. The patch changes pcibios_add_pci_devices() so that it can support full hotplug and so-called "partial" hotplug based on device-tree or real hardware. It's notable that pci_of_scan.c has been changed for a bit in order to support the "partial" hotplug based on dev-tree. Most of the generic code already supports that, we just need to plumb it properly on our side. Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/pci-common.c | 2 ++ arch/powerpc/kernel/pci-hotplug.c | 14 ++++++---- arch/powerpc/kernel/pci_of_scan.c | 56 ++++++++++++++++++++++++++++----------- 3 files changed, 51 insertions(+), 21 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/pci-common.c b/arch/powerpc/kernel/pci-common.c index f46914a0f33..7d22a675fe1 100644 --- a/arch/powerpc/kernel/pci-common.c +++ b/arch/powerpc/kernel/pci-common.c @@ -1462,6 +1462,8 @@ void pcibios_finish_adding_to_bus(struct pci_bus *bus) /* Allocate bus and devices resources */ pcibios_allocate_bus_resources(bus); pcibios_claim_one_bus(bus); + if (!pci_has_flag(PCI_PROBE_ONLY)) + pci_assign_unassigned_bus_resources(bus); /* Fixup EEH */ eeh_add_device_tree_late(bus); diff --git a/arch/powerpc/kernel/pci-hotplug.c b/arch/powerpc/kernel/pci-hotplug.c index fc0831d4971..c1e17ae68a0 100644 --- a/arch/powerpc/kernel/pci-hotplug.c +++ b/arch/powerpc/kernel/pci-hotplug.c @@ -71,7 +71,7 @@ EXPORT_SYMBOL_GPL(pcibios_remove_pci_devices); */ void pcibios_add_pci_devices(struct pci_bus * bus) { - int slotno, num, mode, pass, max; + int slotno, mode, pass, max; struct pci_dev *dev; struct device_node *dn = pci_bus_to_OF_node(bus); @@ -85,11 +85,15 @@ void pcibios_add_pci_devices(struct pci_bus * bus) /* use ofdt-based probe */ of_rescan_bus(dn, bus); } else if (mode == PCI_PROBE_NORMAL) { - /* use legacy probe */ + /* + * Use legacy probe. In the partial hotplug case, we + * probably have grandchildren devices unplugged. So + * we don't check the return value from pci_scan_slot() in + * order for fully rescan all the way down to pick them up. + * They can have been removed during partial hotplug. + */ slotno = PCI_SLOT(PCI_DN(dn->child)->devfn); - num = pci_scan_slot(bus, PCI_DEVFN(slotno, 0)); - if (!num) - return; + pci_scan_slot(bus, PCI_DEVFN(slotno, 0)); pcibios_setup_bus_devices(bus); max = bus->busn_res.start; for (pass = 0; pass < 2; pass++) { diff --git a/arch/powerpc/kernel/pci_of_scan.c b/arch/powerpc/kernel/pci_of_scan.c index 6b0ba5854d9..15d9105323b 100644 --- a/arch/powerpc/kernel/pci_of_scan.c +++ b/arch/powerpc/kernel/pci_of_scan.c @@ -230,11 +230,14 @@ void of_scan_pci_bridge(struct pci_dev *dev) return; } - bus = pci_add_new_bus(dev->bus, dev, busrange[0]); + bus = pci_find_bus(pci_domain_nr(dev->bus), busrange[0]); if (!bus) { - printk(KERN_ERR "Failed to create pci bus for %s\n", - node->full_name); - return; + bus = pci_add_new_bus(dev->bus, dev, busrange[0]); + if (!bus) { + printk(KERN_ERR "Failed to create pci bus for %s\n", + node->full_name); + return; + } } bus->primary = dev->bus->number; @@ -292,6 +295,38 @@ void of_scan_pci_bridge(struct pci_dev *dev) } EXPORT_SYMBOL(of_scan_pci_bridge); +static struct pci_dev *of_scan_pci_dev(struct pci_bus *bus, + struct device_node *dn) +{ + struct pci_dev *dev = NULL; + const u32 *reg; + int reglen, devfn; + + pr_debug(" * %s\n", dn->full_name); + if (!of_device_is_available(dn)) + return NULL; + + reg = of_get_property(dn, "reg", ®len); + if (reg == NULL || reglen < 20) + return NULL; + devfn = (reg[0] >> 8) & 0xff; + + /* Check if the PCI device is already there */ + dev = pci_get_slot(bus, devfn); + if (dev) { + pci_dev_put(dev); + return dev; + } + + /* create a new pci_dev for this device */ + dev = of_create_pci_dev(dn, bus, devfn); + if (!dev) + return NULL; + + pr_debug(" dev header type: %x\n", dev->hdr_type); + return dev; +} + /** * __of_scan_bus - given a PCI bus node, setup bus and scan for child devices * @node: device tree node for the PCI bus @@ -302,8 +337,6 @@ static void __of_scan_bus(struct device_node *node, struct pci_bus *bus, int rescan_existing) { struct device_node *child; - const u32 *reg; - int reglen, devfn; struct pci_dev *dev; pr_debug("of_scan_bus(%s) bus no %d...\n", @@ -311,16 +344,7 @@ static void __of_scan_bus(struct device_node *node, struct pci_bus *bus, /* Scan direct children */ for_each_child_of_node(node, child) { - pr_debug(" * %s\n", child->full_name); - if (!of_device_is_available(child)) - continue; - reg = of_get_property(child, "reg", ®len); - if (reg == NULL || reglen < 20) - continue; - devfn = (reg[0] >> 8) & 0xff; - - /* create a new pci_dev for this device */ - dev = of_create_pci_dev(child, bus, devfn); + dev = of_scan_pci_dev(bus, child); if (!dev) continue; pr_debug(" dev header type: %x\n", dev->hdr_type); -- cgit v1.2.3-70-g09d2 From f5c57710dd62dd06f176934a8b4b8accbf00f9f8 Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:24:58 +0800 Subject: powerpc/eeh: Use partial hotplug for EEH unaware drivers When EEH error happens to one specific PE, some devices with drivers supporting EEH won't except hotplug on the device. However, there might have other deivces without driver, or with driver without EEH support. For the case, we need do partial hotplug in order to make sure that the PE becomes absolutely quite during reset. Otherise, the PE reset might fail and leads to failure of error recovery. The current code doesn't handle that 'mixed' case properly, it either uses the error callbacks to the drivers, or tries hotplug, but doesn't handle a PE (EEH domain) composed of a combination of the two. The patch intends to support so-called "partial" hotplug for EEH: Before we do reset, we stop and remove those PCI devices without EEH sensitive driver. The corresponding EEH devices are not detached from its PE, but with special flag. After the reset is done, those EEH devices with the special flag will be scanned one by one. Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/eeh.h | 6 ++- arch/powerpc/kernel/eeh.c | 30 +++++++++-- arch/powerpc/kernel/eeh_driver.c | 74 ++++++++++++++++++++++++++-- arch/powerpc/kernel/eeh_pe.c | 20 +++----- arch/powerpc/kernel/eeh_sysfs.c | 7 +++ arch/powerpc/platforms/powernv/eeh-powernv.c | 2 +- arch/powerpc/platforms/pseries/eeh_pseries.c | 2 +- 7 files changed, 117 insertions(+), 24 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/eeh.h b/arch/powerpc/include/asm/eeh.h index e8c411b63ca..f54a60131de 100644 --- a/arch/powerpc/include/asm/eeh.h +++ b/arch/powerpc/include/asm/eeh.h @@ -84,7 +84,8 @@ struct eeh_pe { * another tree except the currently existing tree of PCI * buses and PCI devices */ -#define EEH_DEV_IRQ_DISABLED (1<<0) /* Interrupt disabled */ +#define EEH_DEV_IRQ_DISABLED (1 << 0) /* Interrupt disabled */ +#define EEH_DEV_DISCONNECTED (1 << 1) /* Removing from PE */ struct eeh_dev { int mode; /* EEH mode */ @@ -97,6 +98,7 @@ struct eeh_dev { struct pci_controller *phb; /* Associated PHB */ struct device_node *dn; /* Associated device node */ struct pci_dev *pdev; /* Associated PCI device */ + struct pci_bus *bus; /* PCI bus for partial hotplug */ }; static inline struct device_node *eeh_dev_to_of_node(struct eeh_dev *edev) @@ -197,6 +199,8 @@ struct eeh_pe *eeh_pe_get(struct eeh_dev *edev); int eeh_add_to_parent_pe(struct eeh_dev *edev); int eeh_rmv_from_parent_pe(struct eeh_dev *edev); void eeh_pe_update_time_stamp(struct eeh_pe *pe); +void *eeh_pe_traverse(struct eeh_pe *root, + eeh_traverse_func fn, void *flag); void *eeh_pe_dev_traverse(struct eeh_pe *root, eeh_traverse_func fn, void *flag); void eeh_pe_restore_bars(struct eeh_pe *pe); diff --git a/arch/powerpc/kernel/eeh.c b/arch/powerpc/kernel/eeh.c index 56bd4584f61..a5783f1a7a9 100644 --- a/arch/powerpc/kernel/eeh.c +++ b/arch/powerpc/kernel/eeh.c @@ -900,7 +900,21 @@ void eeh_add_device_late(struct pci_dev *dev) pr_debug("EEH: Already referenced !\n"); return; } - WARN_ON(edev->pdev); + + /* + * The EEH cache might not be removed correctly because of + * unbalanced kref to the device during unplug time, which + * relies on pcibios_release_device(). So we have to remove + * that here explicitly. + */ + if (edev->pdev) { + eeh_rmv_from_parent_pe(edev); + eeh_addr_cache_rmv_dev(edev->pdev); + eeh_sysfs_remove_device(edev->pdev); + + edev->pdev = NULL; + dev->dev.archdata.edev = NULL; + } edev->pdev = dev; dev->dev.archdata.edev = edev; @@ -982,14 +996,24 @@ void eeh_remove_device(struct pci_dev *dev) /* Unregister the device with the EEH/PCI address search system */ pr_debug("EEH: Removing device %s\n", pci_name(dev)); - if (!edev || !edev->pdev) { + if (!edev || !edev->pdev || !edev->pe) { pr_debug("EEH: Not referenced !\n"); return; } + + /* + * During the hotplug for EEH error recovery, we need the EEH + * device attached to the parent PE in order for BAR restore + * a bit later. So we keep it for BAR restore and remove it + * from the parent PE during the BAR resotre. + */ edev->pdev = NULL; dev->dev.archdata.edev = NULL; + if (!(edev->pe->state & EEH_PE_KEEP)) + eeh_rmv_from_parent_pe(edev); + else + edev->mode |= EEH_DEV_DISCONNECTED; - eeh_rmv_from_parent_pe(edev); eeh_addr_cache_rmv_dev(dev); eeh_sysfs_remove_device(dev); } diff --git a/arch/powerpc/kernel/eeh_driver.c b/arch/powerpc/kernel/eeh_driver.c index 9ef3bbb8580..9fda75d1f5a 100644 --- a/arch/powerpc/kernel/eeh_driver.c +++ b/arch/powerpc/kernel/eeh_driver.c @@ -338,6 +338,54 @@ static void *eeh_report_failure(void *data, void *userdata) return NULL; } +static void *eeh_rmv_device(void *data, void *userdata) +{ + struct pci_driver *driver; + struct eeh_dev *edev = (struct eeh_dev *)data; + struct pci_dev *dev = eeh_dev_to_pci_dev(edev); + int *removed = (int *)userdata; + + /* + * Actually, we should remove the PCI bridges as well. + * However, that's lots of complexity to do that, + * particularly some of devices under the bridge might + * support EEH. So we just care about PCI devices for + * simplicity here. + */ + if (!dev || (dev->hdr_type & PCI_HEADER_TYPE_BRIDGE)) + return NULL; + driver = eeh_pcid_get(dev); + if (driver && driver->err_handler) + return NULL; + + /* Remove it from PCI subsystem */ + pr_debug("EEH: Removing %s without EEH sensitive driver\n", + pci_name(dev)); + edev->bus = dev->bus; + edev->mode |= EEH_DEV_DISCONNECTED; + (*removed)++; + + pci_stop_and_remove_bus_device(dev); + + return NULL; +} + +static void *eeh_pe_detach_dev(void *data, void *userdata) +{ + struct eeh_pe *pe = (struct eeh_pe *)data; + struct eeh_dev *edev, *tmp; + + eeh_pe_for_each_dev(pe, edev, tmp) { + if (!(edev->mode & EEH_DEV_DISCONNECTED)) + continue; + + edev->mode &= ~(EEH_DEV_DISCONNECTED | EEH_DEV_IRQ_DISABLED); + eeh_rmv_from_parent_pe(edev); + } + + return NULL; +} + /** * eeh_reset_device - Perform actual reset of a pci slot * @pe: EEH PE @@ -349,8 +397,9 @@ static void *eeh_report_failure(void *data, void *userdata) */ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus) { + struct pci_bus *frozen_bus = eeh_pe_bus_get(pe); struct timeval tstamp; - int cnt, rc; + int cnt, rc, removed = 0; /* pcibios will clear the counter; save the value */ cnt = pe->freeze_count; @@ -362,10 +411,11 @@ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus) * devices are expected to be attached soon when calling * into pcibios_add_pci_devices(). */ - if (bus) { - eeh_pe_state_mark(pe, EEH_PE_KEEP); + eeh_pe_state_mark(pe, EEH_PE_KEEP); + if (bus) pcibios_remove_pci_devices(bus); - } + else if (frozen_bus) + eeh_pe_dev_traverse(pe, eeh_rmv_device, &removed); /* Reset the pci controller. (Asserts RST#; resets config space). * Reconfigure bridges and devices. Don't try to bring the system @@ -386,10 +436,24 @@ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus) * potentially weird things happen. */ if (bus) { + pr_info("EEH: Sleep 5s ahead of complete hotplug\n"); ssleep(5); + + /* + * The EEH device is still connected with its parent + * PE. We should disconnect it so the binding can be + * rebuilt when adding PCI devices. + */ + eeh_pe_traverse(pe, eeh_pe_detach_dev, NULL); pcibios_add_pci_devices(bus); - eeh_pe_state_clear(pe, EEH_PE_KEEP); + } else if (frozen_bus && removed) { + pr_info("EEH: Sleep 5s ahead of partial hotplug\n"); + ssleep(5); + + eeh_pe_traverse(pe, eeh_pe_detach_dev, NULL); + pcibios_add_pci_devices(frozen_bus); } + eeh_pe_state_clear(pe, EEH_PE_KEEP); pe->tstamp = tstamp; pe->freeze_count = cnt; diff --git a/arch/powerpc/kernel/eeh_pe.c b/arch/powerpc/kernel/eeh_pe.c index c8b815e45c8..2aa955ae01a 100644 --- a/arch/powerpc/kernel/eeh_pe.c +++ b/arch/powerpc/kernel/eeh_pe.c @@ -149,8 +149,8 @@ static struct eeh_pe *eeh_pe_next(struct eeh_pe *pe, * callback returns something other than NULL, or no more PEs * to be traversed. */ -static void *eeh_pe_traverse(struct eeh_pe *root, - eeh_traverse_func fn, void *flag) +void *eeh_pe_traverse(struct eeh_pe *root, + eeh_traverse_func fn, void *flag) { struct eeh_pe *pe; void *ret; @@ -409,8 +409,8 @@ int eeh_rmv_from_parent_pe(struct eeh_dev *edev) int cnt; if (!edev->pe) { - pr_warning("%s: No PE found for EEH device %s\n", - __func__, edev->dn->full_name); + pr_debug("%s: No PE found for EEH device %s\n", + __func__, edev->dn->full_name); return -EEXIST; } @@ -728,18 +728,12 @@ static void eeh_restore_device_bars(struct eeh_dev *edev, */ static void *eeh_restore_one_device_bars(void *data, void *flag) { - struct pci_dev *pdev = NULL; struct eeh_dev *edev = (struct eeh_dev *)data; + struct pci_dev *pdev = eeh_dev_to_pci_dev(edev); struct device_node *dn = eeh_dev_to_of_node(edev); - /* Trace the PCI bridge */ - if (eeh_probe_mode_dev()) { - pdev = eeh_dev_to_pci_dev(edev); - if (pdev->hdr_type != PCI_HEADER_TYPE_BRIDGE) - pdev = NULL; - } - - if (pdev) + /* Do special restore for bridges */ + if (pdev->hdr_type == PCI_HEADER_TYPE_BRIDGE) eeh_restore_bridge_bars(pdev, edev, dn); else eeh_restore_device_bars(edev, dn); diff --git a/arch/powerpc/kernel/eeh_sysfs.c b/arch/powerpc/kernel/eeh_sysfs.c index e7ae3484918..61e2a145213 100644 --- a/arch/powerpc/kernel/eeh_sysfs.c +++ b/arch/powerpc/kernel/eeh_sysfs.c @@ -68,6 +68,13 @@ void eeh_sysfs_add_device(struct pci_dev *pdev) void eeh_sysfs_remove_device(struct pci_dev *pdev) { + /* + * The parent directory might have been removed. We needn't + * continue for that case. + */ + if (!pdev->dev.kobj.sd) + return; + device_remove_file(&pdev->dev, &dev_attr_eeh_mode); device_remove_file(&pdev->dev, &dev_attr_eeh_config_addr); device_remove_file(&pdev->dev, &dev_attr_eeh_pe_config_addr); diff --git a/arch/powerpc/platforms/powernv/eeh-powernv.c b/arch/powerpc/platforms/powernv/eeh-powernv.c index 969cce73055..a380428cf9c 100644 --- a/arch/powerpc/platforms/powernv/eeh-powernv.c +++ b/arch/powerpc/platforms/powernv/eeh-powernv.c @@ -114,7 +114,7 @@ static int powernv_eeh_dev_probe(struct pci_dev *dev, void *flag) * the root bridge. So it's not reasonable to continue * the probing. */ - if (!dn || !edev) + if (!dn || !edev || edev->pe) return 0; /* Skip for PCI-ISA bridge */ diff --git a/arch/powerpc/platforms/pseries/eeh_pseries.c b/arch/powerpc/platforms/pseries/eeh_pseries.c index b456b157d33..0f44f9fe49a 100644 --- a/arch/powerpc/platforms/pseries/eeh_pseries.c +++ b/arch/powerpc/platforms/pseries/eeh_pseries.c @@ -153,7 +153,7 @@ static void *pseries_eeh_of_probe(struct device_node *dn, void *flag) /* Retrieve OF node and eeh device */ edev = of_node_to_eeh_dev(dn); - if (!of_device_is_available(dn)) + if (edev->pe || !of_device_is_available(dn)) return NULL; /* Retrieve class/vendor/device IDs */ -- cgit v1.2.3-70-g09d2 From 4b83bd452f17582c8d1c916568fd28a237a2eb46 Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:24:59 +0800 Subject: powerpc/eeh: Don't use pci_dev during BAR restore While restoring BARs for one specific PCI device, the pci_dev instance should have been released. So it's not reliable to use the pci_dev instance on restoring BARs. However, we still need some information (e.g. PCIe capability position, header type) from the pci_dev instance. So we have to store those information to EEH device in advance. Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/eeh.h | 8 +++- arch/powerpc/kernel/eeh_pe.c | 25 ++++++----- arch/powerpc/platforms/powernv/eeh-powernv.c | 11 +++++ arch/powerpc/platforms/pseries/eeh_pseries.c | 63 +++++++++++++++++++++++++++- 4 files changed, 91 insertions(+), 16 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/eeh.h b/arch/powerpc/include/asm/eeh.h index f54a60131de..4199d994327 100644 --- a/arch/powerpc/include/asm/eeh.h +++ b/arch/powerpc/include/asm/eeh.h @@ -84,8 +84,11 @@ struct eeh_pe { * another tree except the currently existing tree of PCI * buses and PCI devices */ -#define EEH_DEV_IRQ_DISABLED (1 << 0) /* Interrupt disabled */ -#define EEH_DEV_DISCONNECTED (1 << 1) /* Removing from PE */ +#define EEH_DEV_BRIDGE (1 << 0) /* PCI bridge */ +#define EEH_DEV_ROOT_PORT (1 << 1) /* PCIe root port */ +#define EEH_DEV_DS_PORT (1 << 2) /* Downstream port */ +#define EEH_DEV_IRQ_DISABLED (1 << 3) /* Interrupt disabled */ +#define EEH_DEV_DISCONNECTED (1 << 4) /* Removing from PE */ struct eeh_dev { int mode; /* EEH mode */ @@ -93,6 +96,7 @@ struct eeh_dev { int config_addr; /* Config address */ int pe_config_addr; /* PE config address */ u32 config_space[16]; /* Saved PCI config space */ + u8 pcie_cap; /* Saved PCIe capability */ struct eeh_pe *pe; /* Associated PE */ struct list_head list; /* Form link list in the PE */ struct pci_controller *phb; /* Associated PHB */ diff --git a/arch/powerpc/kernel/eeh_pe.c b/arch/powerpc/kernel/eeh_pe.c index 2aa955ae01a..f9450537e33 100644 --- a/arch/powerpc/kernel/eeh_pe.c +++ b/arch/powerpc/kernel/eeh_pe.c @@ -578,7 +578,7 @@ void eeh_pe_state_clear(struct eeh_pe *pe, int state) * blocked on normal path during the stage. So we need utilize * eeh operations, which is always permitted. */ -static void eeh_bridge_check_link(struct pci_dev *pdev, +static void eeh_bridge_check_link(struct eeh_dev *edev, struct device_node *dn) { int cap; @@ -589,16 +589,17 @@ static void eeh_bridge_check_link(struct pci_dev *pdev, * We only check root port and downstream ports of * PCIe switches */ - if (!pci_is_pcie(pdev) || - (pci_pcie_type(pdev) != PCI_EXP_TYPE_ROOT_PORT && - pci_pcie_type(pdev) != PCI_EXP_TYPE_DOWNSTREAM)) + if (!(edev->mode & (EEH_DEV_ROOT_PORT | EEH_DEV_DS_PORT))) return; - pr_debug("%s: Check PCIe link for %s ...\n", - __func__, pci_name(pdev)); + pr_debug("%s: Check PCIe link for %04x:%02x:%02x.%01x ...\n", + __func__, edev->phb->global_number, + edev->config_addr >> 8, + PCI_SLOT(edev->config_addr & 0xFF), + PCI_FUNC(edev->config_addr & 0xFF)); /* Check slot status */ - cap = pdev->pcie_cap; + cap = edev->pcie_cap; eeh_ops->read_config(dn, cap + PCI_EXP_SLTSTA, 2, &val); if (!(val & PCI_EXP_SLTSTA_PDS)) { pr_debug(" No card in the slot (0x%04x) !\n", val); @@ -652,8 +653,7 @@ static void eeh_bridge_check_link(struct pci_dev *pdev, #define BYTE_SWAP(OFF) (8*((OFF)/4)+3-(OFF)) #define SAVED_BYTE(OFF) (((u8 *)(edev->config_space))[BYTE_SWAP(OFF)]) -static void eeh_restore_bridge_bars(struct pci_dev *pdev, - struct eeh_dev *edev, +static void eeh_restore_bridge_bars(struct eeh_dev *edev, struct device_node *dn) { int i; @@ -679,7 +679,7 @@ static void eeh_restore_bridge_bars(struct pci_dev *pdev, eeh_ops->write_config(dn, PCI_COMMAND, 4, edev->config_space[1]); /* Check the PCIe link is ready */ - eeh_bridge_check_link(pdev, dn); + eeh_bridge_check_link(edev, dn); } static void eeh_restore_device_bars(struct eeh_dev *edev, @@ -729,12 +729,11 @@ static void eeh_restore_device_bars(struct eeh_dev *edev, static void *eeh_restore_one_device_bars(void *data, void *flag) { struct eeh_dev *edev = (struct eeh_dev *)data; - struct pci_dev *pdev = eeh_dev_to_pci_dev(edev); struct device_node *dn = eeh_dev_to_of_node(edev); /* Do special restore for bridges */ - if (pdev->hdr_type == PCI_HEADER_TYPE_BRIDGE) - eeh_restore_bridge_bars(pdev, edev, dn); + if (edev->mode & EEH_DEV_BRIDGE) + eeh_restore_bridge_bars(edev, dn); else eeh_restore_device_bars(edev, dn); diff --git a/arch/powerpc/platforms/powernv/eeh-powernv.c b/arch/powerpc/platforms/powernv/eeh-powernv.c index a380428cf9c..4361a5c7f3a 100644 --- a/arch/powerpc/platforms/powernv/eeh-powernv.c +++ b/arch/powerpc/platforms/powernv/eeh-powernv.c @@ -124,6 +124,17 @@ static int powernv_eeh_dev_probe(struct pci_dev *dev, void *flag) /* Initialize eeh device */ edev->class_code = dev->class; edev->mode = 0; + if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) + edev->mode |= EEH_DEV_BRIDGE; + if (pci_is_pcie(dev)) { + edev->pcie_cap = pci_pcie_cap(dev); + + if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT) + edev->mode |= EEH_DEV_ROOT_PORT; + else if (pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM) + edev->mode |= EEH_DEV_DS_PORT; + } + edev->config_addr = ((dev->bus->number << 8) | dev->devfn); edev->pe_config_addr = phb->bdfn_to_pe(phb, dev->bus, dev->devfn & 0xff); diff --git a/arch/powerpc/platforms/pseries/eeh_pseries.c b/arch/powerpc/platforms/pseries/eeh_pseries.c index 0f44f9fe49a..9e80f0af311 100644 --- a/arch/powerpc/platforms/pseries/eeh_pseries.c +++ b/arch/powerpc/platforms/pseries/eeh_pseries.c @@ -133,6 +133,48 @@ static int pseries_eeh_init(void) return 0; } +static int pseries_eeh_cap_start(struct device_node *dn) +{ + struct pci_dn *pdn = PCI_DN(dn); + u32 status; + + if (!pdn) + return 0; + + rtas_read_config(pdn, PCI_STATUS, 2, &status); + if (!(status & PCI_STATUS_CAP_LIST)) + return 0; + + return PCI_CAPABILITY_LIST; +} + + +static int pseries_eeh_find_cap(struct device_node *dn, int cap) +{ + struct pci_dn *pdn = PCI_DN(dn); + int pos = pseries_eeh_cap_start(dn); + int cnt = 48; /* Maximal number of capabilities */ + u32 id; + + if (!pos) + return 0; + + while (cnt--) { + rtas_read_config(pdn, pos, 1, &pos); + if (pos < 0x40) + break; + pos &= ~3; + rtas_read_config(pdn, pos + PCI_CAP_LIST_ID, 1, &id); + if (id == 0xff) + break; + if (id == cap) + return pos; + pos += PCI_CAP_LIST_NEXT; + } + + return 0; +} + /** * pseries_eeh_of_probe - EEH probe on the given device * @dn: OF node @@ -146,8 +188,10 @@ static void *pseries_eeh_of_probe(struct device_node *dn, void *flag) { struct eeh_dev *edev; struct eeh_pe pe; + struct pci_dn *pdn = PCI_DN(dn); const u32 *class_code, *vendor_id, *device_id; const u32 *regs; + u32 pcie_flags; int enable = 0; int ret; @@ -167,9 +211,26 @@ static void *pseries_eeh_of_probe(struct device_node *dn, void *flag) if (dn->type && !strcmp(dn->type, "isa")) return NULL; - /* Update class code and mode of eeh device */ + /* + * Update class code and mode of eeh device. We need + * correctly reflects that current device is root port + * or PCIe switch downstream port. + */ edev->class_code = *class_code; + edev->pcie_cap = pseries_eeh_find_cap(dn, PCI_CAP_ID_EXP); edev->mode = 0; + if ((edev->class_code >> 8) == PCI_CLASS_BRIDGE_PCI) { + edev->mode |= EEH_DEV_BRIDGE; + if (edev->pcie_cap) { + rtas_read_config(pdn, edev->pcie_cap + PCI_EXP_FLAGS, + 2, &pcie_flags); + pcie_flags = (pcie_flags & PCI_EXP_FLAGS_TYPE) >> 4; + if (pcie_flags == PCI_EXP_TYPE_ROOT_PORT) + edev->mode |= EEH_DEV_ROOT_PORT; + else if (pcie_flags == PCI_EXP_TYPE_DOWNSTREAM) + edev->mode |= EEH_DEV_DS_PORT; + } + } /* Retrieve the device address */ regs = of_get_property(dn, "reg", NULL); -- cgit v1.2.3-70-g09d2 From 91150af3adf67463c4ca7d72d4fe1a84da37792c Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:25:00 +0800 Subject: powerpc/eeh: Fix unbalanced enable for IRQ The patch fixes following issue: Unbalanced enable for IRQ 23 ------------[ cut here ]------------ WARNING: at kernel/irq/manage.c:437 : NIP [c00000000016de8c] .__enable_irq+0x11c/0x140 LR [c00000000016de88] .__enable_irq+0x118/0x140 Call Trace: [c000003ea1f23880] [c00000000016de88] .__enable_irq+0x118/0x140 (unreliable) [c000003ea1f23910] [c00000000016df08] .enable_irq+0x58/0xa0 [c000003ea1f239a0] [c0000000000388b4] .eeh_enable_irq+0xc4/0xe0 [c000003ea1f23a30] [c000000000038a28] .eeh_report_reset+0x78/0x130 [c000003ea1f23ac0] [c000000000037508] .eeh_pe_dev_traverse+0x98/0x170 [c000003ea1f23b60] [c0000000000391ac] .eeh_handle_normal_event+0x2fc/0x3d0 [c000003ea1f23bf0] [c000000000039538] .eeh_handle_event+0x2b8/0x2c0 [c000003ea1f23c90] [c000000000039600] .eeh_event_handler+0xc0/0x170 [c000003ea1f23d30] [c0000000000da9a0] .kthread+0xf0/0x100 [c000003ea1f23e30] [c00000000000a1dc] .ret_from_kernel_thread+0x5c/0x80 Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/eeh_driver.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/eeh_driver.c b/arch/powerpc/kernel/eeh_driver.c index 9fda75d1f5a..36bed5a1275 100644 --- a/arch/powerpc/kernel/eeh_driver.c +++ b/arch/powerpc/kernel/eeh_driver.c @@ -143,10 +143,14 @@ static void eeh_disable_irq(struct pci_dev *dev) static void eeh_enable_irq(struct pci_dev *dev) { struct eeh_dev *edev = pci_dev_to_eeh_dev(dev); + struct irq_desc *desc; if ((edev->mode) & EEH_DEV_IRQ_DISABLED) { edev->mode &= ~EEH_DEV_IRQ_DISABLED; - enable_irq(dev->irq); + + desc = irq_to_desc(dev->irq); + if (desc && desc->depth > 0) + enable_irq(dev->irq); } } -- cgit v1.2.3-70-g09d2 From ab55d2187da27414f78056810713c92f9a4350c2 Mon Sep 17 00:00:00 2001 From: Gavin Shan Date: Wed, 24 Jul 2013 10:25:01 +0800 Subject: powerpc/eeh: Introdce flag to protect sysfs The patch introduces flag EEH_DEV_SYSFS to keep track that the sysfs entries for the corresponding EEH device (then PCI device) has been added or removed, in order to avoid race condition. Signed-off-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/eeh.h | 2 ++ arch/powerpc/kernel/eeh.c | 2 ++ arch/powerpc/kernel/eeh_sysfs.c | 16 +++++++++++++++- arch/powerpc/platforms/powernv/eeh-powernv.c | 4 ++-- arch/powerpc/platforms/pseries/eeh_pseries.c | 2 +- 5 files changed, 22 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/eeh.h b/arch/powerpc/include/asm/eeh.h index 4199d994327..d3e5e9bc8f9 100644 --- a/arch/powerpc/include/asm/eeh.h +++ b/arch/powerpc/include/asm/eeh.h @@ -90,6 +90,8 @@ struct eeh_pe { #define EEH_DEV_IRQ_DISABLED (1 << 3) /* Interrupt disabled */ #define EEH_DEV_DISCONNECTED (1 << 4) /* Removing from PE */ +#define EEH_DEV_SYSFS (1 << 8) /* Sysfs created */ + struct eeh_dev { int mode; /* EEH mode */ int class_code; /* Class code of the device */ diff --git a/arch/powerpc/kernel/eeh.c b/arch/powerpc/kernel/eeh.c index a5783f1a7a9..ea9414c8088 100644 --- a/arch/powerpc/kernel/eeh.c +++ b/arch/powerpc/kernel/eeh.c @@ -911,6 +911,7 @@ void eeh_add_device_late(struct pci_dev *dev) eeh_rmv_from_parent_pe(edev); eeh_addr_cache_rmv_dev(edev->pdev); eeh_sysfs_remove_device(edev->pdev); + edev->mode &= ~EEH_DEV_SYSFS; edev->pdev = NULL; dev->dev.archdata.edev = NULL; @@ -1016,6 +1017,7 @@ void eeh_remove_device(struct pci_dev *dev) eeh_addr_cache_rmv_dev(dev); eeh_sysfs_remove_device(dev); + edev->mode &= ~EEH_DEV_SYSFS; } static int proc_eeh_show(struct seq_file *m, void *v) diff --git a/arch/powerpc/kernel/eeh_sysfs.c b/arch/powerpc/kernel/eeh_sysfs.c index 61e2a145213..5d753d4f2c7 100644 --- a/arch/powerpc/kernel/eeh_sysfs.c +++ b/arch/powerpc/kernel/eeh_sysfs.c @@ -56,26 +56,40 @@ EEH_SHOW_ATTR(eeh_pe_config_addr, pe_config_addr, "0x%x"); void eeh_sysfs_add_device(struct pci_dev *pdev) { + struct eeh_dev *edev = pci_dev_to_eeh_dev(pdev); int rc=0; + if (edev && (edev->mode & EEH_DEV_SYSFS)) + return; + rc += device_create_file(&pdev->dev, &dev_attr_eeh_mode); rc += device_create_file(&pdev->dev, &dev_attr_eeh_config_addr); rc += device_create_file(&pdev->dev, &dev_attr_eeh_pe_config_addr); if (rc) printk(KERN_WARNING "EEH: Unable to create sysfs entries\n"); + else if (edev) + edev->mode |= EEH_DEV_SYSFS; } void eeh_sysfs_remove_device(struct pci_dev *pdev) { + struct eeh_dev *edev = pci_dev_to_eeh_dev(pdev); + /* * The parent directory might have been removed. We needn't * continue for that case. */ - if (!pdev->dev.kobj.sd) + if (!pdev->dev.kobj.sd) { + if (edev) + edev->mode &= ~EEH_DEV_SYSFS; return; + } device_remove_file(&pdev->dev, &dev_attr_eeh_mode); device_remove_file(&pdev->dev, &dev_attr_eeh_config_addr); device_remove_file(&pdev->dev, &dev_attr_eeh_pe_config_addr); + + if (edev) + edev->mode &= ~EEH_DEV_SYSFS; } diff --git a/arch/powerpc/platforms/powernv/eeh-powernv.c b/arch/powerpc/platforms/powernv/eeh-powernv.c index 4361a5c7f3a..79663d26e6e 100644 --- a/arch/powerpc/platforms/powernv/eeh-powernv.c +++ b/arch/powerpc/platforms/powernv/eeh-powernv.c @@ -122,8 +122,8 @@ static int powernv_eeh_dev_probe(struct pci_dev *dev, void *flag) return 0; /* Initialize eeh device */ - edev->class_code = dev->class; - edev->mode = 0; + edev->class_code = dev->class; + edev->mode &= 0xFFFFFF00; if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) edev->mode |= EEH_DEV_BRIDGE; if (pci_is_pcie(dev)) { diff --git a/arch/powerpc/platforms/pseries/eeh_pseries.c b/arch/powerpc/platforms/pseries/eeh_pseries.c index 9e80f0af311..7fbc25b1813 100644 --- a/arch/powerpc/platforms/pseries/eeh_pseries.c +++ b/arch/powerpc/platforms/pseries/eeh_pseries.c @@ -218,7 +218,7 @@ static void *pseries_eeh_of_probe(struct device_node *dn, void *flag) */ edev->class_code = *class_code; edev->pcie_cap = pseries_eeh_find_cap(dn, PCI_CAP_ID_EXP); - edev->mode = 0; + edev->mode &= 0xFFFFFF00; if ((edev->class_code >> 8) == PCI_CLASS_BRIDGE_PCI) { edev->mode |= EEH_DEV_BRIDGE; if (edev->pcie_cap) { -- cgit v1.2.3-70-g09d2 From d817468c4b2892b9468e2a0c92116e38a3a61370 Mon Sep 17 00:00:00 2001 From: Sylwester Nawrocki Date: Wed, 24 Jul 2013 13:23:51 +0900 Subject: ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART This patch restores serial port operation which has been broken since commit 60e93575476f ("serial: samsung: enable clock before clearing pending interrupts during init") That commit only uncovered the real issue which was missing clkdev entries for the "uart" clocks on S3C2440. It went unnoticed so far because return value of clk API calls were not being checked at all in the samsung serial port driver. This patch should be backported to at least 3.10 stable kernel, since the serial port has not been working on s3c2440 since 3.10-rc5. Cc: Chander Kashyap Signed-off-by: Sylwester Nawrocki [on S3C2440 SoC based Mini2440 board] Tested-by: Sylwester Nawrocki Reviewed-by: Tomasz Figa Tested-by: Juergen Beisert Cc: [3.10] Signed-off-by: Kukjin Kim --- arch/arm/mach-s3c24xx/clock-s3c2410.c | 161 ++++++++++++++++++----------- arch/arm/mach-s3c24xx/clock-s3c2440.c | 3 + arch/arm/plat-samsung/include/plat/clock.h | 5 + 3 files changed, 106 insertions(+), 63 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c24xx/clock-s3c2410.c b/arch/arm/mach-s3c24xx/clock-s3c2410.c index 34fffdf6fc1..564553694b5 100644 --- a/arch/arm/mach-s3c24xx/clock-s3c2410.c +++ b/arch/arm/mach-s3c24xx/clock-s3c2410.c @@ -119,66 +119,101 @@ static struct clk init_clocks_off[] = { } }; -static struct clk init_clocks[] = { - { - .name = "lcd", - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_LCDC, - }, { - .name = "gpio", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_GPIO, - }, { - .name = "usb-host", - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_USBH, - }, { - .name = "usb-device", - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_USBD, - }, { - .name = "timers", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_PWMT, - }, { - .name = "uart", - .devname = "s3c2410-uart.0", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART0, - }, { - .name = "uart", - .devname = "s3c2410-uart.1", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART1, - }, { - .name = "uart", - .devname = "s3c2410-uart.2", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART2, - }, { - .name = "rtc", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_RTC, - }, { - .name = "watchdog", - .parent = &clk_p, - .ctrlbit = 0, - }, { - .name = "usb-bus-host", - .parent = &clk_usb_bus, - }, { - .name = "usb-bus-gadget", - .parent = &clk_usb_bus, - }, +static struct clk clk_lcd = { + .name = "lcd", + .parent = &clk_h, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_LCDC, +}; + +static struct clk clk_gpio = { + .name = "gpio", + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_GPIO, +}; + +static struct clk clk_usb_host = { + .name = "usb-host", + .parent = &clk_h, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_USBH, +}; + +static struct clk clk_usb_device = { + .name = "usb-device", + .parent = &clk_h, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_USBD, +}; + +static struct clk clk_timers = { + .name = "timers", + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_PWMT, +}; + +struct clk s3c24xx_clk_uart0 = { + .name = "uart", + .devname = "s3c2410-uart.0", + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART0, +}; + +struct clk s3c24xx_clk_uart1 = { + .name = "uart", + .devname = "s3c2410-uart.1", + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART1, +}; + +struct clk s3c24xx_clk_uart2 = { + .name = "uart", + .devname = "s3c2410-uart.2", + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART2, +}; + +static struct clk clk_rtc = { + .name = "rtc", + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_RTC, +}; + +static struct clk clk_watchdog = { + .name = "watchdog", + .parent = &clk_p, + .ctrlbit = 0, +}; + +static struct clk clk_usb_bus_host = { + .name = "usb-bus-host", + .parent = &clk_usb_bus, +}; + +static struct clk clk_usb_bus_gadget = { + .name = "usb-bus-gadget", + .parent = &clk_usb_bus, +}; + +static struct clk *init_clocks[] = { + &clk_lcd, + &clk_gpio, + &clk_usb_host, + &clk_usb_device, + &clk_timers, + &s3c24xx_clk_uart0, + &s3c24xx_clk_uart1, + &s3c24xx_clk_uart2, + &clk_rtc, + &clk_watchdog, + &clk_usb_bus_host, + &clk_usb_bus_gadget, }; /* s3c2410_baseclk_add() @@ -195,7 +230,6 @@ int __init s3c2410_baseclk_add(void) { unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW); unsigned long clkcon = __raw_readl(S3C2410_CLKCON); - struct clk *clkp; struct clk *xtal; int ret; int ptr; @@ -207,8 +241,9 @@ int __init s3c2410_baseclk_add(void) /* register clocks from clock array */ - clkp = init_clocks; - for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) { + for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++) { + struct clk *clkp = init_clocks[ptr]; + /* ensure that we note the clock state */ clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0; diff --git a/arch/arm/mach-s3c24xx/clock-s3c2440.c b/arch/arm/mach-s3c24xx/clock-s3c2440.c index 1069b568082..aaf006d1d6d 100644 --- a/arch/arm/mach-s3c24xx/clock-s3c2440.c +++ b/arch/arm/mach-s3c24xx/clock-s3c2440.c @@ -166,6 +166,9 @@ static struct clk_lookup s3c2440_clk_lookup[] = { CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk), CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p), CLKDEV_INIT(NULL, "clk_uart_baud3", &s3c2440_clk_fclk_n), + CLKDEV_INIT("s3c2440-uart.0", "uart", &s3c24xx_clk_uart0), + CLKDEV_INIT("s3c2440-uart.1", "uart", &s3c24xx_clk_uart1), + CLKDEV_INIT("s3c2440-uart.2", "uart", &s3c24xx_clk_uart2), CLKDEV_INIT("s3c2440-camif", "camera", &s3c2440_clk_cam_upll), }; diff --git a/arch/arm/plat-samsung/include/plat/clock.h b/arch/arm/plat-samsung/include/plat/clock.h index a62753dc15b..df45d6edc98 100644 --- a/arch/arm/plat-samsung/include/plat/clock.h +++ b/arch/arm/plat-samsung/include/plat/clock.h @@ -83,6 +83,11 @@ extern struct clk clk_ext; extern struct clksrc_clk clk_epllref; extern struct clksrc_clk clk_esysclk; +/* S3C24XX UART clocks */ +extern struct clk s3c24xx_clk_uart0; +extern struct clk s3c24xx_clk_uart1; +extern struct clk s3c24xx_clk_uart2; + /* S3C64XX specific clocks */ extern struct clk clk_h2; extern struct clk clk_27m; -- cgit v1.2.3-70-g09d2 From ad92c615975a57c4b206c5c99f77a0bf22b373c4 Mon Sep 17 00:00:00 2001 From: Denis Kirjanov Date: Tue, 23 Jul 2013 15:28:03 +0400 Subject: powerpc/pseries: Fix a typo in pSeries_lpar_hpte_insert() Commit 801eb73f45371accc78ca9d6d22d647eeb722c11 introduced a bug while checking PTE flags. We have to drop the _PAGE_COHERENT flag when __PAGE_NO_CACHE is set and the cache update policy is not write-through (i.e. _PAGE_WRITETHRU is not set) Signed-off-by: Denis Kirjanov Reviewed-by: Aneesh Kumar K.V CC: Michael Ellerman Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/lpar.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/lpar.c b/arch/powerpc/platforms/pseries/lpar.c index 02d6e21619b..8bad880bd17 100644 --- a/arch/powerpc/platforms/pseries/lpar.c +++ b/arch/powerpc/platforms/pseries/lpar.c @@ -146,7 +146,7 @@ static long pSeries_lpar_hpte_insert(unsigned long hpte_group, flags = 0; /* Make pHyp happy */ - if ((rflags & _PAGE_NO_CACHE) & !(rflags & _PAGE_WRITETHRU)) + if ((rflags & _PAGE_NO_CACHE) && !(rflags & _PAGE_WRITETHRU)) hpte_r &= ~_PAGE_COHERENT; if (firmware_has_feature(FW_FEATURE_XCMO) && !(hpte_r & HPTE_R_N)) flags |= H_COALESCE_CAND; -- cgit v1.2.3-70-g09d2 From 83383b73ad5fbf52ea4b77aed900a927875f2529 Mon Sep 17 00:00:00 2001 From: "Aneesh Kumar K.V" Date: Wed, 3 Jul 2013 13:50:03 +0530 Subject: powerpc/mm: Fix fallthrough bug in hpte_decode We should not fallthrough different case statements in hpte_decode. Add break statement to break out of the switch. The regression is introduced by dcda287a9b26309ae43a091d0ecde16f8f61b4c0 "powerpc/mm: Simplify hpte_decode" Reported-by: Paul Mackerras Signed-off-by: Aneesh Kumar K.V Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/mm/hash_native_64.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/mm/hash_native_64.c b/arch/powerpc/mm/hash_native_64.c index 3f0c30ae479..0530ff78c02 100644 --- a/arch/powerpc/mm/hash_native_64.c +++ b/arch/powerpc/mm/hash_native_64.c @@ -554,6 +554,7 @@ static void hpte_decode(struct hash_pte *hpte, unsigned long slot, seg_off |= vpi << shift; } *vpn = vsid << (SID_SHIFT - VPN_SHIFT) | seg_off >> VPN_SHIFT; + break; case MMU_SEGSIZE_1T: /* We only have 40 - 23 bits of seg_off in avpn */ seg_off = (avpn & 0x1ffff) << 23; @@ -563,6 +564,7 @@ static void hpte_decode(struct hash_pte *hpte, unsigned long slot, seg_off |= vpi << shift; } *vpn = vsid << (SID_SHIFT_1T - VPN_SHIFT) | seg_off >> VPN_SHIFT; + break; default: *vpn = size = 0; } -- cgit v1.2.3-70-g09d2 From de640959b63ad437c21f2a217f25332c4ea863cb Mon Sep 17 00:00:00 2001 From: "Aneesh Kumar K.V" Date: Thu, 4 Jul 2013 10:34:45 +0530 Subject: powerpc/mm: Use the correct SLB(LLP) encoding in tlbie instruction The sllp value is stored in mmu_psize_defs in such a way that we can easily OR the value to get the operand for slbmte instruction. ie, the L and LP bits are not contiguous. Decode the bits and use them correctly in tlbie. regression is introduced by 1f6aaaccb1b3af8613fe45781c1aefee2ae8c6b3 "powerpc: Update tlbie/tlbiel as per ISA doc" Reported-by: Paul Mackerras Signed-off-by: Aneesh Kumar K.V Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/mm/hash_native_64.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/hash_native_64.c b/arch/powerpc/mm/hash_native_64.c index 0530ff78c02..c33d939120c 100644 --- a/arch/powerpc/mm/hash_native_64.c +++ b/arch/powerpc/mm/hash_native_64.c @@ -43,6 +43,7 @@ static inline void __tlbie(unsigned long vpn, int psize, int apsize, int ssize) { unsigned long va; unsigned int penc; + unsigned long sllp; /* * We need 14 to 65 bits of va for a tlibe of 4K page @@ -64,7 +65,9 @@ static inline void __tlbie(unsigned long vpn, int psize, int apsize, int ssize) /* clear out bits after (52) [0....52.....63] */ va &= ~((1ul << (64 - 52)) - 1); va |= ssize << 8; - va |= mmu_psize_defs[apsize].sllp << 6; + sllp = ((mmu_psize_defs[apsize].sllp & SLB_VSID_L) >> 6) | + ((mmu_psize_defs[apsize].sllp & SLB_VSID_LP) >> 4); + va |= sllp << 5; asm volatile(ASM_FTR_IFCLR("tlbie %0,0", PPC_TLBIE(%1,%0), %2) : : "r" (va), "r"(0), "i" (CPU_FTR_ARCH_206) : "memory"); @@ -98,6 +101,7 @@ static inline void __tlbiel(unsigned long vpn, int psize, int apsize, int ssize) { unsigned long va; unsigned int penc; + unsigned long sllp; /* VPN_SHIFT can be atmost 12 */ va = vpn << VPN_SHIFT; @@ -113,7 +117,9 @@ static inline void __tlbiel(unsigned long vpn, int psize, int apsize, int ssize) /* clear out bits after(52) [0....52.....63] */ va &= ~((1ul << (64 - 52)) - 1); va |= ssize << 8; - va |= mmu_psize_defs[apsize].sllp << 6; + sllp = ((mmu_psize_defs[apsize].sllp & SLB_VSID_L) >> 6) | + ((mmu_psize_defs[apsize].sllp & SLB_VSID_LP) >> 4); + va |= sllp << 5; asm volatile(".long 0x7c000224 | (%0 << 11) | (0 << 21)" : : "r"(va) : "memory"); break; -- cgit v1.2.3-70-g09d2 From 679750054ae8129a536734bccf526ff6da35376a Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Tue, 2 Jul 2013 12:20:03 -0600 Subject: powerpc/powernv: Mark pnv_pci_init_ioda2_phb() as __init Mark pnv_pci_init_ioda2_phb() as __init. It is called only from an init function (pnv_pci_init()), and it calls an init function (pnv_pci_init_ioda_phb()): pnv_pci_init # init pnv_pci_init_ioda2_phb # non-init pnv_pci_init_ioda_phb # init This should fix a section mismatch warning. Signed-off-by: Bjorn Helgaas Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/powernv/pci-ioda.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/powernv/pci-ioda.c b/arch/powerpc/platforms/powernv/pci-ioda.c index 49b57b9f835..d8140b125e6 100644 --- a/arch/powerpc/platforms/powernv/pci-ioda.c +++ b/arch/powerpc/platforms/powernv/pci-ioda.c @@ -1266,7 +1266,7 @@ void __init pnv_pci_init_ioda_phb(struct device_node *np, opal_pci_set_pe(phb_id, 0, 0, 7, 1, 1 , OPAL_MAP_PE); } -void pnv_pci_init_ioda2_phb(struct device_node *np) +void __init pnv_pci_init_ioda2_phb(struct device_node *np) { pnv_pci_init_ioda_phb(np, 0, PNV_PHB_IODA2); } -- cgit v1.2.3-70-g09d2 From 7689bdcab1dca061c4c91f0e1703cef1b7b67e71 Mon Sep 17 00:00:00 2001 From: Anshuman Khandual Date: Mon, 10 Jun 2013 11:23:28 +0530 Subject: powerpc/perf: Ignore separate BHRB privilege state filter request Completely ignore BHRB privilege state filter request as we are already configuring that with privilege state filtering attribute for the accompanying PMU event. This would help achieve cleaner user space interaction for BHRB. This patch fixes a situation like this Before patch:- ------------ ./perf record -j any -e branch-misses:k ls Error: The sys_perf_event_open() syscall returned with 95 (Operation not supported) for event (branch-misses:k). /bin/dmesg may provide additional information. No CONFIG_PERF_EVENTS=y kernel support configured? Here 'perf record' actually copies over ':k' filter request into BHRB privilege state filter config and our previous check in kernel would fail that. After patch:- ------------- ./perf record -j any -e branch-misses:k ls perf perf.data perf.data.old test-mmap-ring [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.002 MB perf.data (~102 samples)] Signed-off-by: Anshuman Khandual Acked-by: Michael Neuling Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/perf/power8-pmu.c | 13 ++++--------- 1 file changed, 4 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/perf/power8-pmu.c b/arch/powerpc/perf/power8-pmu.c index 09def196f5c..7466374d278 100644 --- a/arch/powerpc/perf/power8-pmu.c +++ b/arch/powerpc/perf/power8-pmu.c @@ -561,18 +561,13 @@ static int power8_generic_events[] = { static u64 power8_bhrb_filter_map(u64 branch_sample_type) { u64 pmu_bhrb_filter = 0; - u64 br_privilege = branch_sample_type & ONLY_PLM; - /* BHRB and regular PMU events share the same prvillege state + /* BHRB and regular PMU events share the same privilege state * filter configuration. BHRB is always recorded along with a - * regular PMU event. So privilege state filter criteria for BHRB - * and the companion PMU events has to be the same. As a default - * "perf record" tool sets all privillege bits ON when no filter - * criteria is provided in the command line. So as along as all - * privillege bits are ON or they are OFF, we are good to go. + * regular PMU event. As the privilege state filter is handled + * in the basic PMC configuration of the accompanying regular + * PMU event, we ignore any separate BHRB specific request. */ - if ((br_privilege != 7) && (br_privilege != 0)) - return -1; /* No branch filter requested */ if (branch_sample_type & PERF_SAMPLE_BRANCH_ANY) -- cgit v1.2.3-70-g09d2 From ff3d79dc12c2ed38483f6c1e0f26fde430f27c9d Mon Sep 17 00:00:00 2001 From: Anshuman Khandual Date: Mon, 10 Jun 2013 11:23:29 +0530 Subject: powerpc/perf: BHRB filter configuration should follow the task When the task moves around the system, the corresponding cpuhw per cpu strcuture should be popullated with the BHRB filter request value so that PMU could be configured appropriately with that during the next call into power_pmu_enable(). Signed-off-by: Anshuman Khandual Acked-by: Michael Neuling Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/perf/core-book3s.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/perf/core-book3s.c b/arch/powerpc/perf/core-book3s.c index a3985aee77f..24a45f91c65 100644 --- a/arch/powerpc/perf/core-book3s.c +++ b/arch/powerpc/perf/core-book3s.c @@ -1252,8 +1252,11 @@ nocheck: ret = 0; out: - if (has_branch_stack(event)) + if (has_branch_stack(event)) { power_pmu_bhrb_enable(event); + cpuhw->bhrb_filter = ppmu->bhrb_filter_map( + event->attr.branch_sample_type); + } perf_pmu_enable(event->pmu); local_irq_restore(flags); -- cgit v1.2.3-70-g09d2 From 89693016e372983d720c186c0d00b29414b58804 Mon Sep 17 00:00:00 2001 From: Amit Daniel Kachhap Date: Wed, 24 Jul 2013 14:06:13 +0900 Subject: ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm This patch enables the selection of samsung pm related stuffs when SAMSUNG_PM config is enabled and not just when generic PM config is enabled. Power management for s3c64XX and s3c24XX is enabled by default and for other platform depends on S5P_PM. This patch also fixes the following compilation error's when compiling a platform like exynos5440 which does not select pm stuffs. arch/arm/mach-exynos/built-in.o: In function '__virt_to_phys': linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume' linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume' linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume' linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume' arch/arm/mach-exynos/built-in.o: In function 'exynos5_init_irq': linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake' linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake' arch/arm/mach-exynos/built-in.o: In function 'exynos4_init_irq': linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake' linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake' arch/arm/plat-samsung/built-in.o: In function 's3c_irqext_wake': linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow' linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow' arch/arm/plat-samsung/built-in.o: In function 's3c_pm_enter': linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow' linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow' linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow' linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow' linux/arch/arm/plat-samsung/pm.c:275: undefined reference to 's3c_pm_save_core' linux/arch/arm/plat-samsung/pm.c:279: undefined reference to 's3c_pm_configure_extint' linux/arch/arm/plat-samsung/pm.c:310: undefined reference to 's3c_pm_restore_core' make: *** [vmlinux] Error 1 Signed-off-by: Amit Daniel Kachhap Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/Makefile | 2 +- arch/arm/mach-exynos/common.h | 1 - arch/arm/mach-exynos/cpuidle.c | 1 + arch/arm/plat-samsung/Kconfig | 7 +++++++ arch/arm/plat-samsung/Makefile | 2 +- arch/arm/plat-samsung/include/plat/pm.h | 8 ++++---- 6 files changed, 14 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-exynos/Makefile b/arch/arm/mach-exynos/Makefile index e970a7a4e27..53696154aea 100644 --- a/arch/arm/mach-exynos/Makefile +++ b/arch/arm/mach-exynos/Makefile @@ -14,7 +14,7 @@ obj- := obj-$(CONFIG_ARCH_EXYNOS) += common.o -obj-$(CONFIG_PM) += pm.o +obj-$(CONFIG_S5P_PM) += pm.o obj-$(CONFIG_PM_GENERIC_DOMAINS) += pm_domains.o obj-$(CONFIG_CPU_IDLE) += cpuidle.o diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h index 3e156bcddcb..972490fc09d 100644 --- a/arch/arm/mach-exynos/common.h +++ b/arch/arm/mach-exynos/common.h @@ -97,6 +97,5 @@ struct exynos_pmu_conf { }; extern void exynos_sys_powerdown_conf(enum sys_powerdown mode); -extern void s3c_cpu_resume(void); #endif /* __ARCH_ARM_MACH_EXYNOS_COMMON_H */ diff --git a/arch/arm/mach-exynos/cpuidle.c b/arch/arm/mach-exynos/cpuidle.c index 17a18ff3d71..225ee8431c7 100644 --- a/arch/arm/mach-exynos/cpuidle.c +++ b/arch/arm/mach-exynos/cpuidle.c @@ -25,6 +25,7 @@ #include #include +#include #include "common.h" diff --git a/arch/arm/plat-samsung/Kconfig b/arch/arm/plat-samsung/Kconfig index 3dc5cbea86c..a5b5ff6e68d 100644 --- a/arch/arm/plat-samsung/Kconfig +++ b/arch/arm/plat-samsung/Kconfig @@ -29,6 +29,13 @@ config PLAT_S5P help Base platform code for Samsung's S5P series SoC. +config SAMSUNG_PM + bool + depends on PM && (PLAT_S3C24XX || ARCH_S3C64XX || ARCH_S5P64X0 || S5P_PM) + default y + help + Base platform power management code for samsung code + if PLAT_SAMSUNG # boot configurations diff --git a/arch/arm/plat-samsung/Makefile b/arch/arm/plat-samsung/Makefile index 98d07d8fc7a..199bbe304d0 100644 --- a/arch/arm/plat-samsung/Makefile +++ b/arch/arm/plat-samsung/Makefile @@ -51,7 +51,7 @@ obj-$(CONFIG_SAMSUNG_DMADEV) += dma-ops.o # PM support -obj-$(CONFIG_PM) += pm.o +obj-$(CONFIG_SAMSUNG_PM) += pm.o obj-$(CONFIG_SAMSUNG_PM_GPIO) += pm-gpio.o obj-$(CONFIG_SAMSUNG_PM_CHECK) += pm-check.o diff --git a/arch/arm/plat-samsung/include/plat/pm.h b/arch/arm/plat-samsung/include/plat/pm.h index 5d47ca35cab..6bc1a8f471e 100644 --- a/arch/arm/plat-samsung/include/plat/pm.h +++ b/arch/arm/plat-samsung/include/plat/pm.h @@ -19,7 +19,7 @@ struct device; -#ifdef CONFIG_PM +#ifdef CONFIG_SAMSUNG_PM extern __init int s3c_pm_init(void); extern __init int s3c64xx_pm_init(void); @@ -58,8 +58,6 @@ extern unsigned char pm_uart_udivslot; /* true to save UART UDIVSLOT */ /* from sleep.S */ -extern void s3c_cpu_resume(void); - extern int s3c2410_cpu_suspend(unsigned long); /* sleep save info */ @@ -106,12 +104,14 @@ extern void s3c_pm_do_save(struct sleep_save *ptr, int count); extern void s3c_pm_do_restore(struct sleep_save *ptr, int count); extern void s3c_pm_do_restore_core(struct sleep_save *ptr, int count); -#ifdef CONFIG_PM +#ifdef CONFIG_SAMSUNG_PM extern int s3c_irq_wake(struct irq_data *data, unsigned int state); extern int s3c_irqext_wake(struct irq_data *data, unsigned int state); +extern void s3c_cpu_resume(void); #else #define s3c_irq_wake NULL #define s3c_irqext_wake NULL +#define s3c_cpu_resume NULL #endif /* PM debug functions */ -- cgit v1.2.3-70-g09d2 From e70308ec0e4bff344fcfdf160de40e1150552c5f Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Wed, 24 Jul 2013 17:04:16 +1000 Subject: Revert "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework" This reverts commits 67822649d7305caf3dd50ed46c27b99c94eff996 39761214eefc6b070f29402aa1165f24d789b3f7 0b95a7f85718adcbba36407ef88bba0a7379ed03 31d939625a9a20b1badd2d4e6bf6fd39fa523405 2d31e518a42828df7877bca23a958627d60408bc Unfortunately this change broke boot on some systems that used an initrd which does not include the newly created crct10dif modules. As these modules are required by sd_mod under certain configurations this is a serious problem. Signed-off-by: Herbert Xu --- arch/x86/crypto/Makefile | 2 - arch/x86/crypto/crct10dif-pcl-asm_64.S | 643 -------------------------------- arch/x86/crypto/crct10dif-pclmul_glue.c | 151 -------- crypto/Kconfig | 19 - crypto/Makefile | 1 - crypto/crct10dif.c | 178 --------- crypto/tcrypt.c | 8 - crypto/testmgr.c | 10 - crypto/testmgr.h | 33 -- include/linux/crc-t10dif.h | 4 - lib/Kconfig | 2 - lib/crc-t10dif.c | 73 ++-- 12 files changed, 43 insertions(+), 1081 deletions(-) delete mode 100644 arch/x86/crypto/crct10dif-pcl-asm_64.S delete mode 100644 arch/x86/crypto/crct10dif-pclmul_glue.c delete mode 100644 crypto/crct10dif.c (limited to 'arch') diff --git a/arch/x86/crypto/Makefile b/arch/x86/crypto/Makefile index 7d6ba9db1be..6c63c358a7e 100644 --- a/arch/x86/crypto/Makefile +++ b/arch/x86/crypto/Makefile @@ -27,7 +27,6 @@ obj-$(CONFIG_CRYPTO_SHA1_SSSE3) += sha1-ssse3.o obj-$(CONFIG_CRYPTO_CRC32_PCLMUL) += crc32-pclmul.o obj-$(CONFIG_CRYPTO_SHA256_SSSE3) += sha256-ssse3.o obj-$(CONFIG_CRYPTO_SHA512_SSSE3) += sha512-ssse3.o -obj-$(CONFIG_CRYPTO_CRCT10DIF_PCLMUL) += crct10dif-pclmul.o # These modules require assembler to support AVX. ifeq ($(avx_supported),yes) @@ -82,4 +81,3 @@ crc32c-intel-$(CONFIG_64BIT) += crc32c-pcl-intel-asm_64.o crc32-pclmul-y := crc32-pclmul_asm.o crc32-pclmul_glue.o sha256-ssse3-y := sha256-ssse3-asm.o sha256-avx-asm.o sha256-avx2-asm.o sha256_ssse3_glue.o sha512-ssse3-y := sha512-ssse3-asm.o sha512-avx-asm.o sha512-avx2-asm.o sha512_ssse3_glue.o -crct10dif-pclmul-y := crct10dif-pcl-asm_64.o crct10dif-pclmul_glue.o diff --git a/arch/x86/crypto/crct10dif-pcl-asm_64.S b/arch/x86/crypto/crct10dif-pcl-asm_64.S deleted file mode 100644 index 35e97569d05..00000000000 --- a/arch/x86/crypto/crct10dif-pcl-asm_64.S +++ /dev/null @@ -1,643 +0,0 @@ -######################################################################## -# Implement fast CRC-T10DIF computation with SSE and PCLMULQDQ instructions -# -# Copyright (c) 2013, Intel Corporation -# -# Authors: -# Erdinc Ozturk -# Vinodh Gopal -# James Guilford -# Tim Chen -# -# This software is available to you under a choice of one of two -# licenses. You may choose to be licensed under the terms of the GNU -# General Public License (GPL) Version 2, available from the file -# COPYING in the main directory of this source tree, or the -# OpenIB.org BSD license below: -# -# Redistribution and use in source and binary forms, with or without -# modification, are permitted provided that the following conditions are -# met: -# -# * Redistributions of source code must retain the above copyright -# notice, this list of conditions and the following disclaimer. -# -# * Redistributions in binary form must reproduce the above copyright -# notice, this list of conditions and the following disclaimer in the -# documentation and/or other materials provided with the -# distribution. -# -# * Neither the name of the Intel Corporation nor the names of its -# contributors may be used to endorse or promote products derived from -# this software without specific prior written permission. -# -# -# THIS SOFTWARE IS PROVIDED BY INTEL CORPORATION ""AS IS"" AND ANY -# EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -# IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR -# PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL INTEL CORPORATION OR -# CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, -# EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, -# PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR -# PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF -# LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING -# NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS -# SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. -######################################################################## -# Function API: -# UINT16 crc_t10dif_pcl( -# UINT16 init_crc, //initial CRC value, 16 bits -# const unsigned char *buf, //buffer pointer to calculate CRC on -# UINT64 len //buffer length in bytes (64-bit data) -# ); -# -# Reference paper titled "Fast CRC Computation for Generic -# Polynomials Using PCLMULQDQ Instruction" -# URL: http://www.intel.com/content/dam/www/public/us/en/documents -# /white-papers/fast-crc-computation-generic-polynomials-pclmulqdq-paper.pdf -# -# - -#include - -.text - -#define arg1 %rdi -#define arg2 %rsi -#define arg3 %rdx - -#define arg1_low32 %edi - -ENTRY(crc_t10dif_pcl) -.align 16 - - # adjust the 16-bit initial_crc value, scale it to 32 bits - shl $16, arg1_low32 - - # Allocate Stack Space - mov %rsp, %rcx - sub $16*2, %rsp - # align stack to 16 byte boundary - and $~(0x10 - 1), %rsp - - # check if smaller than 256 - cmp $256, arg3 - - # for sizes less than 128, we can't fold 64B at a time... - jl _less_than_128 - - - # load the initial crc value - movd arg1_low32, %xmm10 # initial crc - - # crc value does not need to be byte-reflected, but it needs - # to be moved to the high part of the register. - # because data will be byte-reflected and will align with - # initial crc at correct place. - pslldq $12, %xmm10 - - movdqa SHUF_MASK(%rip), %xmm11 - # receive the initial 64B data, xor the initial crc value - movdqu 16*0(arg2), %xmm0 - movdqu 16*1(arg2), %xmm1 - movdqu 16*2(arg2), %xmm2 - movdqu 16*3(arg2), %xmm3 - movdqu 16*4(arg2), %xmm4 - movdqu 16*5(arg2), %xmm5 - movdqu 16*6(arg2), %xmm6 - movdqu 16*7(arg2), %xmm7 - - pshufb %xmm11, %xmm0 - # XOR the initial_crc value - pxor %xmm10, %xmm0 - pshufb %xmm11, %xmm1 - pshufb %xmm11, %xmm2 - pshufb %xmm11, %xmm3 - pshufb %xmm11, %xmm4 - pshufb %xmm11, %xmm5 - pshufb %xmm11, %xmm6 - pshufb %xmm11, %xmm7 - - movdqa rk3(%rip), %xmm10 #xmm10 has rk3 and rk4 - #imm value of pclmulqdq instruction - #will determine which constant to use - - ################################################################# - # we subtract 256 instead of 128 to save one instruction from the loop - sub $256, arg3 - - # at this section of the code, there is 64*x+y (0<=y<64) bytes of - # buffer. The _fold_64_B_loop will fold 64B at a time - # until we have 64+y Bytes of buffer - - - # fold 64B at a time. This section of the code folds 4 xmm - # registers in parallel -_fold_64_B_loop: - - # update the buffer pointer - add $128, arg2 # buf += 64# - - movdqu 16*0(arg2), %xmm9 - movdqu 16*1(arg2), %xmm12 - pshufb %xmm11, %xmm9 - pshufb %xmm11, %xmm12 - movdqa %xmm0, %xmm8 - movdqa %xmm1, %xmm13 - pclmulqdq $0x0 , %xmm10, %xmm0 - pclmulqdq $0x11, %xmm10, %xmm8 - pclmulqdq $0x0 , %xmm10, %xmm1 - pclmulqdq $0x11, %xmm10, %xmm13 - pxor %xmm9 , %xmm0 - xorps %xmm8 , %xmm0 - pxor %xmm12, %xmm1 - xorps %xmm13, %xmm1 - - movdqu 16*2(arg2), %xmm9 - movdqu 16*3(arg2), %xmm12 - pshufb %xmm11, %xmm9 - pshufb %xmm11, %xmm12 - movdqa %xmm2, %xmm8 - movdqa %xmm3, %xmm13 - pclmulqdq $0x0, %xmm10, %xmm2 - pclmulqdq $0x11, %xmm10, %xmm8 - pclmulqdq $0x0, %xmm10, %xmm3 - pclmulqdq $0x11, %xmm10, %xmm13 - pxor %xmm9 , %xmm2 - xorps %xmm8 , %xmm2 - pxor %xmm12, %xmm3 - xorps %xmm13, %xmm3 - - movdqu 16*4(arg2), %xmm9 - movdqu 16*5(arg2), %xmm12 - pshufb %xmm11, %xmm9 - pshufb %xmm11, %xmm12 - movdqa %xmm4, %xmm8 - movdqa %xmm5, %xmm13 - pclmulqdq $0x0, %xmm10, %xmm4 - pclmulqdq $0x11, %xmm10, %xmm8 - pclmulqdq $0x0, %xmm10, %xmm5 - pclmulqdq $0x11, %xmm10, %xmm13 - pxor %xmm9 , %xmm4 - xorps %xmm8 , %xmm4 - pxor %xmm12, %xmm5 - xorps %xmm13, %xmm5 - - movdqu 16*6(arg2), %xmm9 - movdqu 16*7(arg2), %xmm12 - pshufb %xmm11, %xmm9 - pshufb %xmm11, %xmm12 - movdqa %xmm6 , %xmm8 - movdqa %xmm7 , %xmm13 - pclmulqdq $0x0 , %xmm10, %xmm6 - pclmulqdq $0x11, %xmm10, %xmm8 - pclmulqdq $0x0 , %xmm10, %xmm7 - pclmulqdq $0x11, %xmm10, %xmm13 - pxor %xmm9 , %xmm6 - xorps %xmm8 , %xmm6 - pxor %xmm12, %xmm7 - xorps %xmm13, %xmm7 - - sub $128, arg3 - - # check if there is another 64B in the buffer to be able to fold - jge _fold_64_B_loop - ################################################################## - - - add $128, arg2 - # at this point, the buffer pointer is pointing at the last y Bytes - # of the buffer the 64B of folded data is in 4 of the xmm - # registers: xmm0, xmm1, xmm2, xmm3 - - - # fold the 8 xmm registers to 1 xmm register with different constants - - movdqa rk9(%rip), %xmm10 - movdqa %xmm0, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm0 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - xorps %xmm0, %xmm7 - - movdqa rk11(%rip), %xmm10 - movdqa %xmm1, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm1 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - xorps %xmm1, %xmm7 - - movdqa rk13(%rip), %xmm10 - movdqa %xmm2, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm2 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - pxor %xmm2, %xmm7 - - movdqa rk15(%rip), %xmm10 - movdqa %xmm3, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm3 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - xorps %xmm3, %xmm7 - - movdqa rk17(%rip), %xmm10 - movdqa %xmm4, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm4 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - pxor %xmm4, %xmm7 - - movdqa rk19(%rip), %xmm10 - movdqa %xmm5, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm5 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - xorps %xmm5, %xmm7 - - movdqa rk1(%rip), %xmm10 #xmm10 has rk1 and rk2 - #imm value of pclmulqdq instruction - #will determine which constant to use - movdqa %xmm6, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm6 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - pxor %xmm6, %xmm7 - - - # instead of 64, we add 48 to the loop counter to save 1 instruction - # from the loop instead of a cmp instruction, we use the negative - # flag with the jl instruction - add $128-16, arg3 - jl _final_reduction_for_128 - - # now we have 16+y bytes left to reduce. 16 Bytes is in register xmm7 - # and the rest is in memory. We can fold 16 bytes at a time if y>=16 - # continue folding 16B at a time - -_16B_reduction_loop: - movdqa %xmm7, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm7 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - movdqu (arg2), %xmm0 - pshufb %xmm11, %xmm0 - pxor %xmm0 , %xmm7 - add $16, arg2 - sub $16, arg3 - # instead of a cmp instruction, we utilize the flags with the - # jge instruction equivalent of: cmp arg3, 16-16 - # check if there is any more 16B in the buffer to be able to fold - jge _16B_reduction_loop - - #now we have 16+z bytes left to reduce, where 0<= z < 16. - #first, we reduce the data in the xmm7 register - - -_final_reduction_for_128: - # check if any more data to fold. If not, compute the CRC of - # the final 128 bits - add $16, arg3 - je _128_done - - # here we are getting data that is less than 16 bytes. - # since we know that there was data before the pointer, we can - # offset the input pointer before the actual point, to receive - # exactly 16 bytes. after that the registers need to be adjusted. -_get_last_two_xmms: - movdqa %xmm7, %xmm2 - - movdqu -16(arg2, arg3), %xmm1 - pshufb %xmm11, %xmm1 - - # get rid of the extra data that was loaded before - # load the shift constant - lea pshufb_shf_table+16(%rip), %rax - sub arg3, %rax - movdqu (%rax), %xmm0 - - # shift xmm2 to the left by arg3 bytes - pshufb %xmm0, %xmm2 - - # shift xmm7 to the right by 16-arg3 bytes - pxor mask1(%rip), %xmm0 - pshufb %xmm0, %xmm7 - pblendvb %xmm2, %xmm1 #xmm0 is implicit - - # fold 16 Bytes - movdqa %xmm1, %xmm2 - movdqa %xmm7, %xmm8 - pclmulqdq $0x11, %xmm10, %xmm7 - pclmulqdq $0x0 , %xmm10, %xmm8 - pxor %xmm8, %xmm7 - pxor %xmm2, %xmm7 - -_128_done: - # compute crc of a 128-bit value - movdqa rk5(%rip), %xmm10 # rk5 and rk6 in xmm10 - movdqa %xmm7, %xmm0 - - #64b fold - pclmulqdq $0x1, %xmm10, %xmm7 - pslldq $8 , %xmm0 - pxor %xmm0, %xmm7 - - #32b fold - movdqa %xmm7, %xmm0 - - pand mask2(%rip), %xmm0 - - psrldq $12, %xmm7 - pclmulqdq $0x10, %xmm10, %xmm7 - pxor %xmm0, %xmm7 - - #barrett reduction -_barrett: - movdqa rk7(%rip), %xmm10 # rk7 and rk8 in xmm10 - movdqa %xmm7, %xmm0 - pclmulqdq $0x01, %xmm10, %xmm7 - pslldq $4, %xmm7 - pclmulqdq $0x11, %xmm10, %xmm7 - - pslldq $4, %xmm7 - pxor %xmm0, %xmm7 - pextrd $1, %xmm7, %eax - -_cleanup: - # scale the result back to 16 bits - shr $16, %eax - mov %rcx, %rsp - ret - -######################################################################## - -.align 16 -_less_than_128: - - # check if there is enough buffer to be able to fold 16B at a time - cmp $32, arg3 - jl _less_than_32 - movdqa SHUF_MASK(%rip), %xmm11 - - # now if there is, load the constants - movdqa rk1(%rip), %xmm10 # rk1 and rk2 in xmm10 - - movd arg1_low32, %xmm0 # get the initial crc value - pslldq $12, %xmm0 # align it to its correct place - movdqu (arg2), %xmm7 # load the plaintext - pshufb %xmm11, %xmm7 # byte-reflect the plaintext - pxor %xmm0, %xmm7 - - - # update the buffer pointer - add $16, arg2 - - # update the counter. subtract 32 instead of 16 to save one - # instruction from the loop - sub $32, arg3 - - jmp _16B_reduction_loop - - -.align 16 -_less_than_32: - # mov initial crc to the return value. this is necessary for - # zero-length buffers. - mov arg1_low32, %eax - test arg3, arg3 - je _cleanup - - movdqa SHUF_MASK(%rip), %xmm11 - - movd arg1_low32, %xmm0 # get the initial crc value - pslldq $12, %xmm0 # align it to its correct place - - cmp $16, arg3 - je _exact_16_left - jl _less_than_16_left - - movdqu (arg2), %xmm7 # load the plaintext - pshufb %xmm11, %xmm7 # byte-reflect the plaintext - pxor %xmm0 , %xmm7 # xor the initial crc value - add $16, arg2 - sub $16, arg3 - movdqa rk1(%rip), %xmm10 # rk1 and rk2 in xmm10 - jmp _get_last_two_xmms - - -.align 16 -_less_than_16_left: - # use stack space to load data less than 16 bytes, zero-out - # the 16B in memory first. - - pxor %xmm1, %xmm1 - mov %rsp, %r11 - movdqa %xmm1, (%r11) - - cmp $4, arg3 - jl _only_less_than_4 - - # backup the counter value - mov arg3, %r9 - cmp $8, arg3 - jl _less_than_8_left - - # load 8 Bytes - mov (arg2), %rax - mov %rax, (%r11) - add $8, %r11 - sub $8, arg3 - add $8, arg2 -_less_than_8_left: - - cmp $4, arg3 - jl _less_than_4_left - - # load 4 Bytes - mov (arg2), %eax - mov %eax, (%r11) - add $4, %r11 - sub $4, arg3 - add $4, arg2 -_less_than_4_left: - - cmp $2, arg3 - jl _less_than_2_left - - # load 2 Bytes - mov (arg2), %ax - mov %ax, (%r11) - add $2, %r11 - sub $2, arg3 - add $2, arg2 -_less_than_2_left: - cmp $1, arg3 - jl _zero_left - - # load 1 Byte - mov (arg2), %al - mov %al, (%r11) -_zero_left: - movdqa (%rsp), %xmm7 - pshufb %xmm11, %xmm7 - pxor %xmm0 , %xmm7 # xor the initial crc value - - # shl r9, 4 - lea pshufb_shf_table+16(%rip), %rax - sub %r9, %rax - movdqu (%rax), %xmm0 - pxor mask1(%rip), %xmm0 - - pshufb %xmm0, %xmm7 - jmp _128_done - -.align 16 -_exact_16_left: - movdqu (arg2), %xmm7 - pshufb %xmm11, %xmm7 - pxor %xmm0 , %xmm7 # xor the initial crc value - - jmp _128_done - -_only_less_than_4: - cmp $3, arg3 - jl _only_less_than_3 - - # load 3 Bytes - mov (arg2), %al - mov %al, (%r11) - - mov 1(arg2), %al - mov %al, 1(%r11) - - mov 2(arg2), %al - mov %al, 2(%r11) - - movdqa (%rsp), %xmm7 - pshufb %xmm11, %xmm7 - pxor %xmm0 , %xmm7 # xor the initial crc value - - psrldq $5, %xmm7 - - jmp _barrett -_only_less_than_3: - cmp $2, arg3 - jl _only_less_than_2 - - # load 2 Bytes - mov (arg2), %al - mov %al, (%r11) - - mov 1(arg2), %al - mov %al, 1(%r11) - - movdqa (%rsp), %xmm7 - pshufb %xmm11, %xmm7 - pxor %xmm0 , %xmm7 # xor the initial crc value - - psrldq $6, %xmm7 - - jmp _barrett -_only_less_than_2: - - # load 1 Byte - mov (arg2), %al - mov %al, (%r11) - - movdqa (%rsp), %xmm7 - pshufb %xmm11, %xmm7 - pxor %xmm0 , %xmm7 # xor the initial crc value - - psrldq $7, %xmm7 - - jmp _barrett - -ENDPROC(crc_t10dif_pcl) - -.data - -# precomputed constants -# these constants are precomputed from the poly: -# 0x8bb70000 (0x8bb7 scaled to 32 bits) -.align 16 -# Q = 0x18BB70000 -# rk1 = 2^(32*3) mod Q << 32 -# rk2 = 2^(32*5) mod Q << 32 -# rk3 = 2^(32*15) mod Q << 32 -# rk4 = 2^(32*17) mod Q << 32 -# rk5 = 2^(32*3) mod Q << 32 -# rk6 = 2^(32*2) mod Q << 32 -# rk7 = floor(2^64/Q) -# rk8 = Q -rk1: -.quad 0x2d56000000000000 -rk2: -.quad 0x06df000000000000 -rk3: -.quad 0x9d9d000000000000 -rk4: -.quad 0x7cf5000000000000 -rk5: -.quad 0x2d56000000000000 -rk6: -.quad 0x1368000000000000 -rk7: -.quad 0x00000001f65a57f8 -rk8: -.quad 0x000000018bb70000 - -rk9: -.quad 0xceae000000000000 -rk10: -.quad 0xbfd6000000000000 -rk11: -.quad 0x1e16000000000000 -rk12: -.quad 0x713c000000000000 -rk13: -.quad 0xf7f9000000000000 -rk14: -.quad 0x80a6000000000000 -rk15: -.quad 0x044c000000000000 -rk16: -.quad 0xe658000000000000 -rk17: -.quad 0xad18000000000000 -rk18: -.quad 0xa497000000000000 -rk19: -.quad 0x6ee3000000000000 -rk20: -.quad 0xe7b5000000000000 - - - -mask1: -.octa 0x80808080808080808080808080808080 -mask2: -.octa 0x00000000FFFFFFFFFFFFFFFFFFFFFFFF - -SHUF_MASK: -.octa 0x000102030405060708090A0B0C0D0E0F - -pshufb_shf_table: -# use these values for shift constants for the pshufb instruction -# different alignments result in values as shown: -# DDQ 0x008f8e8d8c8b8a898887868584838281 # shl 15 (16-1) / shr1 -# DDQ 0x01008f8e8d8c8b8a8988878685848382 # shl 14 (16-3) / shr2 -# DDQ 0x0201008f8e8d8c8b8a89888786858483 # shl 13 (16-4) / shr3 -# DDQ 0x030201008f8e8d8c8b8a898887868584 # shl 12 (16-4) / shr4 -# DDQ 0x04030201008f8e8d8c8b8a8988878685 # shl 11 (16-5) / shr5 -# DDQ 0x0504030201008f8e8d8c8b8a89888786 # shl 10 (16-6) / shr6 -# DDQ 0x060504030201008f8e8d8c8b8a898887 # shl 9 (16-7) / shr7 -# DDQ 0x07060504030201008f8e8d8c8b8a8988 # shl 8 (16-8) / shr8 -# DDQ 0x0807060504030201008f8e8d8c8b8a89 # shl 7 (16-9) / shr9 -# DDQ 0x090807060504030201008f8e8d8c8b8a # shl 6 (16-10) / shr10 -# DDQ 0x0a090807060504030201008f8e8d8c8b # shl 5 (16-11) / shr11 -# DDQ 0x0b0a090807060504030201008f8e8d8c # shl 4 (16-12) / shr12 -# DDQ 0x0c0b0a090807060504030201008f8e8d # shl 3 (16-13) / shr13 -# DDQ 0x0d0c0b0a090807060504030201008f8e # shl 2 (16-14) / shr14 -# DDQ 0x0e0d0c0b0a090807060504030201008f # shl 1 (16-15) / shr15 -.octa 0x8f8e8d8c8b8a89888786858483828100 -.octa 0x000e0d0c0b0a09080706050403020100 diff --git a/arch/x86/crypto/crct10dif-pclmul_glue.c b/arch/x86/crypto/crct10dif-pclmul_glue.c deleted file mode 100644 index 7845d7fd54c..00000000000 --- a/arch/x86/crypto/crct10dif-pclmul_glue.c +++ /dev/null @@ -1,151 +0,0 @@ -/* - * Cryptographic API. - * - * T10 Data Integrity Field CRC16 Crypto Transform using PCLMULQDQ Instructions - * - * Copyright (C) 2013 Intel Corporation - * Author: Tim Chen - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the Free - * Software Foundation; either version 2 of the License, or (at your option) - * any later version. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF - * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS - * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN - * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN - * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE - * SOFTWARE. - * - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -asmlinkage __u16 crc_t10dif_pcl(__u16 crc, const unsigned char *buf, - size_t len); - -struct chksum_desc_ctx { - __u16 crc; -}; - -/* - * Steps through buffer one byte at at time, calculates reflected - * crc using table. - */ - -static int chksum_init(struct shash_desc *desc) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - ctx->crc = 0; - - return 0; -} - -static int chksum_update(struct shash_desc *desc, const u8 *data, - unsigned int length) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - if (irq_fpu_usable()) { - kernel_fpu_begin(); - ctx->crc = crc_t10dif_pcl(ctx->crc, data, length); - kernel_fpu_end(); - } else - ctx->crc = crc_t10dif_generic(ctx->crc, data, length); - return 0; -} - -static int chksum_final(struct shash_desc *desc, u8 *out) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - *(__u16 *)out = ctx->crc; - return 0; -} - -static int __chksum_finup(__u16 *crcp, const u8 *data, unsigned int len, - u8 *out) -{ - if (irq_fpu_usable()) { - kernel_fpu_begin(); - *(__u16 *)out = crc_t10dif_pcl(*crcp, data, len); - kernel_fpu_end(); - } else - *(__u16 *)out = crc_t10dif_generic(*crcp, data, len); - return 0; -} - -static int chksum_finup(struct shash_desc *desc, const u8 *data, - unsigned int len, u8 *out) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - return __chksum_finup(&ctx->crc, data, len, out); -} - -static int chksum_digest(struct shash_desc *desc, const u8 *data, - unsigned int length, u8 *out) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - return __chksum_finup(&ctx->crc, data, length, out); -} - -static struct shash_alg alg = { - .digestsize = CRC_T10DIF_DIGEST_SIZE, - .init = chksum_init, - .update = chksum_update, - .final = chksum_final, - .finup = chksum_finup, - .digest = chksum_digest, - .descsize = sizeof(struct chksum_desc_ctx), - .base = { - .cra_name = "crct10dif", - .cra_driver_name = "crct10dif-pclmul", - .cra_priority = 200, - .cra_blocksize = CRC_T10DIF_BLOCK_SIZE, - .cra_module = THIS_MODULE, - } -}; - -static const struct x86_cpu_id crct10dif_cpu_id[] = { - X86_FEATURE_MATCH(X86_FEATURE_PCLMULQDQ), - {} -}; -MODULE_DEVICE_TABLE(x86cpu, crct10dif_cpu_id); - -static int __init crct10dif_intel_mod_init(void) -{ - if (!x86_match_cpu(crct10dif_cpu_id)) - return -ENODEV; - - return crypto_register_shash(&alg); -} - -static void __exit crct10dif_intel_mod_fini(void) -{ - crypto_unregister_shash(&alg); -} - -module_init(crct10dif_intel_mod_init); -module_exit(crct10dif_intel_mod_fini); - -MODULE_AUTHOR("Tim Chen "); -MODULE_DESCRIPTION("T10 DIF CRC calculation accelerated with PCLMULQDQ."); -MODULE_LICENSE("GPL"); - -MODULE_ALIAS("crct10dif"); -MODULE_ALIAS("crct10dif-pclmul"); diff --git a/crypto/Kconfig b/crypto/Kconfig index 904ffe83856..2754f2bf5d9 100644 --- a/crypto/Kconfig +++ b/crypto/Kconfig @@ -376,25 +376,6 @@ config CRYPTO_CRC32_PCLMUL which will enable any routine to use the CRC-32-IEEE 802.3 checksum and gain better performance as compared with the table implementation. -config CRYPTO_CRCT10DIF - tristate "CRCT10DIF algorithm" - select CRYPTO_HASH - help - CRC T10 Data Integrity Field computation is being cast as - a crypto transform. This allows for faster crc t10 diff - transforms to be used if they are available. - -config CRYPTO_CRCT10DIF_PCLMUL - tristate "CRCT10DIF PCLMULQDQ hardware acceleration" - depends on X86 && 64BIT && CRC_T10DIF - select CRYPTO_HASH - help - For x86_64 processors with SSE4.2 and PCLMULQDQ supported, - CRC T10 DIF PCLMULQDQ computation can be hardware - accelerated PCLMULQDQ instruction. This option will create - 'crct10dif-plcmul' module, which is faster when computing the - crct10dif checksum as compared with the generic table implementation. - config CRYPTO_GHASH tristate "GHASH digest algorithm" select CRYPTO_GF128MUL diff --git a/crypto/Makefile b/crypto/Makefile index 62af87df872..a8e9b0fefbe 100644 --- a/crypto/Makefile +++ b/crypto/Makefile @@ -83,7 +83,6 @@ obj-$(CONFIG_CRYPTO_ZLIB) += zlib.o obj-$(CONFIG_CRYPTO_MICHAEL_MIC) += michael_mic.o obj-$(CONFIG_CRYPTO_CRC32C) += crc32c.o obj-$(CONFIG_CRYPTO_CRC32) += crc32.o -obj-$(CONFIG_CRYPTO_CRCT10DIF) += crct10dif.o obj-$(CONFIG_CRYPTO_AUTHENC) += authenc.o authencesn.o obj-$(CONFIG_CRYPTO_LZO) += lzo.o obj-$(CONFIG_CRYPTO_842) += 842.o diff --git a/crypto/crct10dif.c b/crypto/crct10dif.c deleted file mode 100644 index 92aca96d6b9..00000000000 --- a/crypto/crct10dif.c +++ /dev/null @@ -1,178 +0,0 @@ -/* - * Cryptographic API. - * - * T10 Data Integrity Field CRC16 Crypto Transform - * - * Copyright (c) 2007 Oracle Corporation. All rights reserved. - * Written by Martin K. Petersen - * Copyright (C) 2013 Intel Corporation - * Author: Tim Chen - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the Free - * Software Foundation; either version 2 of the License, or (at your option) - * any later version. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF - * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS - * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN - * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN - * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE - * SOFTWARE. - * - */ - -#include -#include -#include -#include -#include -#include -#include - -struct chksum_desc_ctx { - __u16 crc; -}; - -/* Table generated using the following polynomium: - * x^16 + x^15 + x^11 + x^9 + x^8 + x^7 + x^5 + x^4 + x^2 + x + 1 - * gt: 0x8bb7 - */ -static const __u16 t10_dif_crc_table[256] = { - 0x0000, 0x8BB7, 0x9CD9, 0x176E, 0xB205, 0x39B2, 0x2EDC, 0xA56B, - 0xEFBD, 0x640A, 0x7364, 0xF8D3, 0x5DB8, 0xD60F, 0xC161, 0x4AD6, - 0x54CD, 0xDF7A, 0xC814, 0x43A3, 0xE6C8, 0x6D7F, 0x7A11, 0xF1A6, - 0xBB70, 0x30C7, 0x27A9, 0xAC1E, 0x0975, 0x82C2, 0x95AC, 0x1E1B, - 0xA99A, 0x222D, 0x3543, 0xBEF4, 0x1B9F, 0x9028, 0x8746, 0x0CF1, - 0x4627, 0xCD90, 0xDAFE, 0x5149, 0xF422, 0x7F95, 0x68FB, 0xE34C, - 0xFD57, 0x76E0, 0x618E, 0xEA39, 0x4F52, 0xC4E5, 0xD38B, 0x583C, - 0x12EA, 0x995D, 0x8E33, 0x0584, 0xA0EF, 0x2B58, 0x3C36, 0xB781, - 0xD883, 0x5334, 0x445A, 0xCFED, 0x6A86, 0xE131, 0xF65F, 0x7DE8, - 0x373E, 0xBC89, 0xABE7, 0x2050, 0x853B, 0x0E8C, 0x19E2, 0x9255, - 0x8C4E, 0x07F9, 0x1097, 0x9B20, 0x3E4B, 0xB5FC, 0xA292, 0x2925, - 0x63F3, 0xE844, 0xFF2A, 0x749D, 0xD1F6, 0x5A41, 0x4D2F, 0xC698, - 0x7119, 0xFAAE, 0xEDC0, 0x6677, 0xC31C, 0x48AB, 0x5FC5, 0xD472, - 0x9EA4, 0x1513, 0x027D, 0x89CA, 0x2CA1, 0xA716, 0xB078, 0x3BCF, - 0x25D4, 0xAE63, 0xB90D, 0x32BA, 0x97D1, 0x1C66, 0x0B08, 0x80BF, - 0xCA69, 0x41DE, 0x56B0, 0xDD07, 0x786C, 0xF3DB, 0xE4B5, 0x6F02, - 0x3AB1, 0xB106, 0xA668, 0x2DDF, 0x88B4, 0x0303, 0x146D, 0x9FDA, - 0xD50C, 0x5EBB, 0x49D5, 0xC262, 0x6709, 0xECBE, 0xFBD0, 0x7067, - 0x6E7C, 0xE5CB, 0xF2A5, 0x7912, 0xDC79, 0x57CE, 0x40A0, 0xCB17, - 0x81C1, 0x0A76, 0x1D18, 0x96AF, 0x33C4, 0xB873, 0xAF1D, 0x24AA, - 0x932B, 0x189C, 0x0FF2, 0x8445, 0x212E, 0xAA99, 0xBDF7, 0x3640, - 0x7C96, 0xF721, 0xE04F, 0x6BF8, 0xCE93, 0x4524, 0x524A, 0xD9FD, - 0xC7E6, 0x4C51, 0x5B3F, 0xD088, 0x75E3, 0xFE54, 0xE93A, 0x628D, - 0x285B, 0xA3EC, 0xB482, 0x3F35, 0x9A5E, 0x11E9, 0x0687, 0x8D30, - 0xE232, 0x6985, 0x7EEB, 0xF55C, 0x5037, 0xDB80, 0xCCEE, 0x4759, - 0x0D8F, 0x8638, 0x9156, 0x1AE1, 0xBF8A, 0x343D, 0x2353, 0xA8E4, - 0xB6FF, 0x3D48, 0x2A26, 0xA191, 0x04FA, 0x8F4D, 0x9823, 0x1394, - 0x5942, 0xD2F5, 0xC59B, 0x4E2C, 0xEB47, 0x60F0, 0x779E, 0xFC29, - 0x4BA8, 0xC01F, 0xD771, 0x5CC6, 0xF9AD, 0x721A, 0x6574, 0xEEC3, - 0xA415, 0x2FA2, 0x38CC, 0xB37B, 0x1610, 0x9DA7, 0x8AC9, 0x017E, - 0x1F65, 0x94D2, 0x83BC, 0x080B, 0xAD60, 0x26D7, 0x31B9, 0xBA0E, - 0xF0D8, 0x7B6F, 0x6C01, 0xE7B6, 0x42DD, 0xC96A, 0xDE04, 0x55B3 -}; - -__u16 crc_t10dif_generic(__u16 crc, const unsigned char *buffer, size_t len) -{ - unsigned int i; - - for (i = 0 ; i < len ; i++) - crc = (crc << 8) ^ t10_dif_crc_table[((crc >> 8) ^ buffer[i]) & 0xff]; - - return crc; -} -EXPORT_SYMBOL(crc_t10dif_generic); - -/* - * Steps through buffer one byte at at time, calculates reflected - * crc using table. - */ - -static int chksum_init(struct shash_desc *desc) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - ctx->crc = 0; - - return 0; -} - -static int chksum_update(struct shash_desc *desc, const u8 *data, - unsigned int length) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - ctx->crc = crc_t10dif_generic(ctx->crc, data, length); - return 0; -} - -static int chksum_final(struct shash_desc *desc, u8 *out) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - *(__u16 *)out = ctx->crc; - return 0; -} - -static int __chksum_finup(__u16 *crcp, const u8 *data, unsigned int len, - u8 *out) -{ - *(__u16 *)out = crc_t10dif_generic(*crcp, data, len); - return 0; -} - -static int chksum_finup(struct shash_desc *desc, const u8 *data, - unsigned int len, u8 *out) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - return __chksum_finup(&ctx->crc, data, len, out); -} - -static int chksum_digest(struct shash_desc *desc, const u8 *data, - unsigned int length, u8 *out) -{ - struct chksum_desc_ctx *ctx = shash_desc_ctx(desc); - - return __chksum_finup(&ctx->crc, data, length, out); -} - -static struct shash_alg alg = { - .digestsize = CRC_T10DIF_DIGEST_SIZE, - .init = chksum_init, - .update = chksum_update, - .final = chksum_final, - .finup = chksum_finup, - .digest = chksum_digest, - .descsize = sizeof(struct chksum_desc_ctx), - .base = { - .cra_name = "crct10dif", - .cra_driver_name = "crct10dif-generic", - .cra_priority = 100, - .cra_blocksize = CRC_T10DIF_BLOCK_SIZE, - .cra_module = THIS_MODULE, - } -}; - -static int __init crct10dif_mod_init(void) -{ - int ret; - - ret = crypto_register_shash(&alg); - return ret; -} - -static void __exit crct10dif_mod_fini(void) -{ - crypto_unregister_shash(&alg); -} - -module_init(crct10dif_mod_init); -module_exit(crct10dif_mod_fini); - -MODULE_AUTHOR("Tim Chen "); -MODULE_DESCRIPTION("T10 DIF CRC calculation."); -MODULE_LICENSE("GPL"); diff --git a/crypto/tcrypt.c b/crypto/tcrypt.c index 25a5934f0e5..66d254ce0d1 100644 --- a/crypto/tcrypt.c +++ b/crypto/tcrypt.c @@ -1174,10 +1174,6 @@ static int do_test(int m) ret += tcrypt_test("ghash"); break; - case 47: - ret += tcrypt_test("crct10dif"); - break; - case 100: ret += tcrypt_test("hmac(md5)"); break; @@ -1502,10 +1498,6 @@ static int do_test(int m) test_hash_speed("crc32c", sec, generic_hash_speed_template); if (mode > 300 && mode < 400) break; - case 320: - test_hash_speed("crct10dif", sec, generic_hash_speed_template); - if (mode > 300 && mode < 400) break; - case 399: break; diff --git a/crypto/testmgr.c b/crypto/testmgr.c index 2f00607039e..ecddf921a9d 100644 --- a/crypto/testmgr.c +++ b/crypto/testmgr.c @@ -2045,16 +2045,6 @@ static const struct alg_test_desc alg_test_descs[] = { .count = CRC32C_TEST_VECTORS } } - }, { - .alg = "crct10dif", - .test = alg_test_hash, - .fips_allowed = 1, - .suite = { - .hash = { - .vecs = crct10dif_tv_template, - .count = CRCT10DIF_TEST_VECTORS - } - } }, { .alg = "cryptd(__driver-cbc-aes-aesni)", .test = alg_test_null, diff --git a/crypto/testmgr.h b/crypto/testmgr.h index 7d44aa3d6b4..1e701bc075b 100644 --- a/crypto/testmgr.h +++ b/crypto/testmgr.h @@ -450,39 +450,6 @@ static struct hash_testvec rmd320_tv_template[] = { } }; -#define CRCT10DIF_TEST_VECTORS 3 -static struct hash_testvec crct10dif_tv_template[] = { - { - .plaintext = "abc", - .psize = 3, -#ifdef __LITTLE_ENDIAN - .digest = "\x3b\x44", -#else - .digest = "\x44\x3b", -#endif - }, { - .plaintext = "1234567890123456789012345678901234567890" - "123456789012345678901234567890123456789", - .psize = 79, -#ifdef __LITTLE_ENDIAN - .digest = "\x70\x4b", -#else - .digest = "\x4b\x70", -#endif - }, { - .plaintext = - "abcddddddddddddddddddddddddddddddddddddddddddddddddddddd", - .psize = 56, -#ifdef __LITTLE_ENDIAN - .digest = "\xe3\x9c", -#else - .digest = "\x9c\xe3", -#endif - .np = 2, - .tap = { 28, 28 } - } -}; - /* * SHA1 test vectors from from FIPS PUB 180-1 * Long vector from CAVS 5.0 diff --git a/include/linux/crc-t10dif.h b/include/linux/crc-t10dif.h index b3cb71f0d3b..a9c96d865ee 100644 --- a/include/linux/crc-t10dif.h +++ b/include/linux/crc-t10dif.h @@ -3,10 +3,6 @@ #include -#define CRC_T10DIF_DIGEST_SIZE 2 -#define CRC_T10DIF_BLOCK_SIZE 1 - -__u16 crc_t10dif_generic(__u16 crc, const unsigned char *buffer, size_t len); __u16 crc_t10dif(unsigned char const *, size_t); #endif diff --git a/lib/Kconfig b/lib/Kconfig index 339d5a4292f..fe01d418b09 100644 --- a/lib/Kconfig +++ b/lib/Kconfig @@ -63,8 +63,6 @@ config CRC16 config CRC_T10DIF tristate "CRC calculation for the T10 Data Integrity Field" - select CRYPTO - select CRYPTO_CRCT10DIF help This option is only needed if a module that's not in the kernel tree needs to calculate CRC checks for use with the diff --git a/lib/crc-t10dif.c b/lib/crc-t10dif.c index fe3428c07b4..fbbd66ed86c 100644 --- a/lib/crc-t10dif.c +++ b/lib/crc-t10dif.c @@ -11,44 +11,57 @@ #include #include #include -#include -#include -#include -static struct crypto_shash *crct10dif_tfm; +/* Table generated using the following polynomium: + * x^16 + x^15 + x^11 + x^9 + x^8 + x^7 + x^5 + x^4 + x^2 + x + 1 + * gt: 0x8bb7 + */ +static const __u16 t10_dif_crc_table[256] = { + 0x0000, 0x8BB7, 0x9CD9, 0x176E, 0xB205, 0x39B2, 0x2EDC, 0xA56B, + 0xEFBD, 0x640A, 0x7364, 0xF8D3, 0x5DB8, 0xD60F, 0xC161, 0x4AD6, + 0x54CD, 0xDF7A, 0xC814, 0x43A3, 0xE6C8, 0x6D7F, 0x7A11, 0xF1A6, + 0xBB70, 0x30C7, 0x27A9, 0xAC1E, 0x0975, 0x82C2, 0x95AC, 0x1E1B, + 0xA99A, 0x222D, 0x3543, 0xBEF4, 0x1B9F, 0x9028, 0x8746, 0x0CF1, + 0x4627, 0xCD90, 0xDAFE, 0x5149, 0xF422, 0x7F95, 0x68FB, 0xE34C, + 0xFD57, 0x76E0, 0x618E, 0xEA39, 0x4F52, 0xC4E5, 0xD38B, 0x583C, + 0x12EA, 0x995D, 0x8E33, 0x0584, 0xA0EF, 0x2B58, 0x3C36, 0xB781, + 0xD883, 0x5334, 0x445A, 0xCFED, 0x6A86, 0xE131, 0xF65F, 0x7DE8, + 0x373E, 0xBC89, 0xABE7, 0x2050, 0x853B, 0x0E8C, 0x19E2, 0x9255, + 0x8C4E, 0x07F9, 0x1097, 0x9B20, 0x3E4B, 0xB5FC, 0xA292, 0x2925, + 0x63F3, 0xE844, 0xFF2A, 0x749D, 0xD1F6, 0x5A41, 0x4D2F, 0xC698, + 0x7119, 0xFAAE, 0xEDC0, 0x6677, 0xC31C, 0x48AB, 0x5FC5, 0xD472, + 0x9EA4, 0x1513, 0x027D, 0x89CA, 0x2CA1, 0xA716, 0xB078, 0x3BCF, + 0x25D4, 0xAE63, 0xB90D, 0x32BA, 0x97D1, 0x1C66, 0x0B08, 0x80BF, + 0xCA69, 0x41DE, 0x56B0, 0xDD07, 0x786C, 0xF3DB, 0xE4B5, 0x6F02, + 0x3AB1, 0xB106, 0xA668, 0x2DDF, 0x88B4, 0x0303, 0x146D, 0x9FDA, + 0xD50C, 0x5EBB, 0x49D5, 0xC262, 0x6709, 0xECBE, 0xFBD0, 0x7067, + 0x6E7C, 0xE5CB, 0xF2A5, 0x7912, 0xDC79, 0x57CE, 0x40A0, 0xCB17, + 0x81C1, 0x0A76, 0x1D18, 0x96AF, 0x33C4, 0xB873, 0xAF1D, 0x24AA, + 0x932B, 0x189C, 0x0FF2, 0x8445, 0x212E, 0xAA99, 0xBDF7, 0x3640, + 0x7C96, 0xF721, 0xE04F, 0x6BF8, 0xCE93, 0x4524, 0x524A, 0xD9FD, + 0xC7E6, 0x4C51, 0x5B3F, 0xD088, 0x75E3, 0xFE54, 0xE93A, 0x628D, + 0x285B, 0xA3EC, 0xB482, 0x3F35, 0x9A5E, 0x11E9, 0x0687, 0x8D30, + 0xE232, 0x6985, 0x7EEB, 0xF55C, 0x5037, 0xDB80, 0xCCEE, 0x4759, + 0x0D8F, 0x8638, 0x9156, 0x1AE1, 0xBF8A, 0x343D, 0x2353, 0xA8E4, + 0xB6FF, 0x3D48, 0x2A26, 0xA191, 0x04FA, 0x8F4D, 0x9823, 0x1394, + 0x5942, 0xD2F5, 0xC59B, 0x4E2C, 0xEB47, 0x60F0, 0x779E, 0xFC29, + 0x4BA8, 0xC01F, 0xD771, 0x5CC6, 0xF9AD, 0x721A, 0x6574, 0xEEC3, + 0xA415, 0x2FA2, 0x38CC, 0xB37B, 0x1610, 0x9DA7, 0x8AC9, 0x017E, + 0x1F65, 0x94D2, 0x83BC, 0x080B, 0xAD60, 0x26D7, 0x31B9, 0xBA0E, + 0xF0D8, 0x7B6F, 0x6C01, 0xE7B6, 0x42DD, 0xC96A, 0xDE04, 0x55B3 +}; __u16 crc_t10dif(const unsigned char *buffer, size_t len) { - struct { - struct shash_desc shash; - char ctx[2]; - } desc; - int err; - - desc.shash.tfm = crct10dif_tfm; - desc.shash.flags = 0; - *(__u16 *)desc.ctx = 0; + __u16 crc = 0; + unsigned int i; - err = crypto_shash_update(&desc.shash, buffer, len); - BUG_ON(err); + for (i = 0 ; i < len ; i++) + crc = (crc << 8) ^ t10_dif_crc_table[((crc >> 8) ^ buffer[i]) & 0xff]; - return *(__u16 *)desc.ctx; + return crc; } EXPORT_SYMBOL(crc_t10dif); -static int __init crc_t10dif_mod_init(void) -{ - crct10dif_tfm = crypto_alloc_shash("crct10dif", 0, 0); - return PTR_RET(crct10dif_tfm); -} - -static void __exit crc_t10dif_mod_fini(void) -{ - crypto_free_shash(crct10dif_tfm); -} - -module_init(crc_t10dif_mod_init); -module_exit(crc_t10dif_mod_fini); - MODULE_DESCRIPTION("T10 DIF CRC calculation"); MODULE_LICENSE("GPL"); -- cgit v1.2.3-70-g09d2 From 7bdc84fb82627f34d9e13c37926f70fcde38e4c4 Mon Sep 17 00:00:00 2001 From: Yadwinder Singh Brar Date: Wed, 24 Jul 2013 17:05:07 +0900 Subject: ARM: SAMSUNG: Save/restore only selected uart's registers Basically this code gets executed only during debugging i.e when DEBUG_LL & SAMSUNG_PM_DEBUG is on, so required only for UART used for debugging. Since we are removing static iodesc entries for UARTs, so now only the selected (CONFIG_DEBUG_S3C_UART) UART will be ioremapped by the debug_ll_io_init() for DEBUG_LL, so save/restore uart registers only for selected uart. Signed-off-by: Yadwinder Singh Brar Signed-off-by: Kukjin Kim --- arch/arm/plat-samsung/pm.c | 14 +++----------- 1 file changed, 3 insertions(+), 11 deletions(-) (limited to 'arch') diff --git a/arch/arm/plat-samsung/pm.c b/arch/arm/plat-samsung/pm.c index ea361364245..d0c23010b69 100644 --- a/arch/arm/plat-samsung/pm.c +++ b/arch/arm/plat-samsung/pm.c @@ -80,7 +80,7 @@ unsigned char pm_uart_udivslot; #ifdef CONFIG_SAMSUNG_PM_DEBUG -static struct pm_uart_save uart_save[CONFIG_SERIAL_SAMSUNG_UARTS]; +static struct pm_uart_save uart_save; static void s3c_pm_save_uart(unsigned int uart, struct pm_uart_save *save) { @@ -101,11 +101,7 @@ static void s3c_pm_save_uart(unsigned int uart, struct pm_uart_save *save) static void s3c_pm_save_uarts(void) { - struct pm_uart_save *save = uart_save; - unsigned int uart; - - for (uart = 0; uart < CONFIG_SERIAL_SAMSUNG_UARTS; uart++, save++) - s3c_pm_save_uart(uart, save); + s3c_pm_save_uart(CONFIG_DEBUG_S3C_UART, &uart_save); } static void s3c_pm_restore_uart(unsigned int uart, struct pm_uart_save *save) @@ -126,11 +122,7 @@ static void s3c_pm_restore_uart(unsigned int uart, struct pm_uart_save *save) static void s3c_pm_restore_uarts(void) { - struct pm_uart_save *save = uart_save; - unsigned int uart; - - for (uart = 0; uart < CONFIG_SERIAL_SAMSUNG_UARTS; uart++, save++) - s3c_pm_restore_uart(uart, save); + s3c_pm_restore_uart(CONFIG_DEBUG_S3C_UART, &uart_save); } #else static void s3c_pm_save_uarts(void) { } -- cgit v1.2.3-70-g09d2 From 7ed76e089a645a12c53bc35936574f710aa11549 Mon Sep 17 00:00:00 2001 From: Yadwinder Singh Brar Date: Wed, 24 Jul 2013 17:05:32 +0900 Subject: ARM: EXYNOS: Fix low level debug support Presently, using exynos_defconfig with CONFIG_DEBUG_LL and CONFIG_EARLY_PRIN on, kernel is not booting, we are getting following: [ 0.000000] ------------[ cut here ]------------ [ 0.000000] kernel BUG at mm/vmalloc.c:1134! [ 0.000000] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc1 #633 [ 0.000000] task: c052ec48 ti: c0524000 task.ti: c0524000 [ 0.000000] PC is at vm_area_add_early+0x54/0x94 [ 0.000000] LR is at add_static_vm_early+0xc/0x60 Its because exynos[4/5]_map_io() function ioremaps a single 512KB memory size for all the four uart ports which envelopes the mapping created by debug_ll_io_init(), called earlier in exynos_init_io(). This patch removes iodesc entries for UART controller for all Samsung SoC's, since now the Samsung uart driver does a ioremap during probe and any needed iomapping for earlyprintk will be handled by debug_ll_io_init(). Tested on smdk4412 and smdk5250. Signed-off-by: Yadwinder Singh Brar Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/common.c | 26 -------------------------- 1 file changed, 26 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c index 164685bd25c..ba95e5db250 100644 --- a/arch/arm/mach-exynos/common.c +++ b/arch/arm/mach-exynos/common.c @@ -58,7 +58,6 @@ static const char name_exynos5440[] = "EXYNOS5440"; static void exynos4_map_io(void); static void exynos5_map_io(void); -static void exynos5440_map_io(void); static int exynos_init(void); static struct cpu_table cpu_ids[] __initdata = { @@ -95,7 +94,6 @@ static struct cpu_table cpu_ids[] __initdata = { }, { .idcode = EXYNOS5440_SOC_ID, .idmask = EXYNOS5_SOC_MASK, - .map_io = exynos5440_map_io, .init = exynos_init, .name = name_exynos5440, }, @@ -149,11 +147,6 @@ static struct map_desc exynos4_iodesc[] __initdata = { .pfn = __phys_to_pfn(EXYNOS4_PA_GIC_DIST), .length = SZ_64K, .type = MT_DEVICE, - }, { - .virtual = (unsigned long)S3C_VA_UART, - .pfn = __phys_to_pfn(EXYNOS4_PA_UART), - .length = SZ_512K, - .type = MT_DEVICE, }, { .virtual = (unsigned long)S5P_VA_CMU, .pfn = __phys_to_pfn(EXYNOS4_PA_CMU), @@ -268,20 +261,6 @@ static struct map_desc exynos5_iodesc[] __initdata = { .pfn = __phys_to_pfn(EXYNOS5_PA_PMU), .length = SZ_64K, .type = MT_DEVICE, - }, { - .virtual = (unsigned long)S3C_VA_UART, - .pfn = __phys_to_pfn(EXYNOS5_PA_UART), - .length = SZ_512K, - .type = MT_DEVICE, - }, -}; - -static struct map_desc exynos5440_iodesc0[] __initdata = { - { - .virtual = (unsigned long)S3C_VA_UART, - .pfn = __phys_to_pfn(EXYNOS5440_PA_UART0), - .length = SZ_512K, - .type = MT_DEVICE, }, }; @@ -388,11 +367,6 @@ static void __init exynos5_map_io(void) iotable_init(exynos5250_iodesc, ARRAY_SIZE(exynos5250_iodesc)); } -static void __init exynos5440_map_io(void) -{ - iotable_init(exynos5440_iodesc0, ARRAY_SIZE(exynos5440_iodesc0)); -} - void __init exynos_init_time(void) { of_clk_init(NULL); -- cgit v1.2.3-70-g09d2 From 53302bf60d2c95ee42118008499a5f5de544fcc1 Mon Sep 17 00:00:00 2001 From: Sachin Kamat Date: Wed, 24 Jul 2013 18:55:27 +0900 Subject: ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos With the recent cleanup in Exynos platform code notably commits 17859bec ("ARM: EXYNOS: Do not select legacy Kconfig symbols any more") and b9222210 ("ARM: EXYNOS: Remove mach/gpio.h"), the definition of ARCH_NR_GPIOS got removed. This started causing problems on SoCs like Exynos4412 which have more than the default number of GPIOs. Thus define this number in KConfig file which takes care of current SoC requirements and provides scope for GPIO expanders. Without this patch we get the following errors during boot: gpiochip_add: gpios 251..258 (gpv0) failed to register samsung-pinctrl 106e0000.pinctrl: failed to register gpio_chip gpv0, error code: -22 samsung-pinctrl: probe of 106e0000.pinctrl failed with error -22 Signed-off-by: Sachin Kamat Cc: Tomasz Figa Signed-off-by: Kukjin Kim --- arch/arm/Kconfig | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index ba412e02ec0..37c0f4e978d 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1600,8 +1600,7 @@ config LOCAL_TIMERS config ARCH_NR_GPIO int default 1024 if ARCH_SHMOBILE || ARCH_TEGRA - default 512 if SOC_OMAP5 - default 512 if ARCH_KEYSTONE + default 512 if ARCH_EXYNOS || ARCH_KEYSTONE || SOC_OMAP5 default 392 if ARCH_U8500 default 352 if ARCH_VT8500 default 288 if ARCH_SUNXI -- cgit v1.2.3-70-g09d2 From f82a3133c0c5625d54f3dd1621815b1cf77c8463 Mon Sep 17 00:00:00 2001 From: Olof Johansson Date: Wed, 24 Jul 2013 16:55:23 -0700 Subject: ARM: omap5: Only select errata 798181 if SMP MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Avoids the following warning when SMP is off: warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which has unmet direct dependencies (CPU_V7 && SMP) Reported-by: Emilio López Cc: Tony Lindgren Cc: Santosh Shilimkar Signed-off-by: Olof Johansson --- arch/arm/mach-omap2/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 627fa7e41fb..3eed0006d18 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -62,7 +62,7 @@ config SOC_OMAP5 select HAVE_SMP select COMMON_CLK select HAVE_ARM_ARCH_TIMER - select ARM_ERRATA_798181 + select ARM_ERRATA_798181 if SMP config SOC_AM33XX bool "AM33XX support" -- cgit v1.2.3-70-g09d2 From 16b551dd22cc7edacb952f7a2e175f36c3aa4bdb Mon Sep 17 00:00:00 2001 From: Kuninori Morimoto Date: Wed, 24 Jul 2013 17:50:50 -0700 Subject: ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code 89ae7b5bbd3e65bc6ab7a577ca5ec18569589c8c (ARM: shmobile: armadillo800eva: Register pinctrl mapping for INTC) mistakenly requests GPIO 166 in board code, most probably due to a wrong merge conflict resolution. As the GPIO is passed to the st1232 driver through platform data and requested by the driver, there's no need to request it in board code. Fix it. Tested by: Cao Minh Hiep Acked-by: Laurent Pinchart Signed-off-by: Kuninori Morimoto Signed-off-by: Simon Horman --- arch/arm/mach-shmobile/board-armadillo800eva.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c index e115f674210..c5be60d85e4 100644 --- a/arch/arm/mach-shmobile/board-armadillo800eva.c +++ b/arch/arm/mach-shmobile/board-armadillo800eva.c @@ -1162,9 +1162,6 @@ static void __init eva_init(void) gpio_request_one(61, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */ gpio_request_one(202, GPIOF_OUT_INIT_LOW, NULL); /* LCD0_LED_CONT */ - /* Touchscreen */ - gpio_request_one(166, GPIOF_OUT_INIT_HIGH, NULL); /* TP_RST_B */ - /* GETHER */ gpio_request_one(18, GPIOF_OUT_INIT_HIGH, NULL); /* PHY_RST */ -- cgit v1.2.3-70-g09d2 From 7cd29f4b22be3c3468871f5240621a32d9bc903a Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Wed, 24 Jul 2013 11:36:31 -0600 Subject: PCI: hotplug: Convert to be builtin only, not modular Convert CONFIG_HOTPLUG_PCI from tristate to bool. This only affects the hotplug core; several of the hotplug drivers can still be modules. Signed-off-by: Bjorn Helgaas Acked-by: Rafael J. Wysocki Acked-by: Yinghai Lu --- arch/ia64/configs/generic_defconfig | 2 +- arch/ia64/configs/gensparse_defconfig | 2 +- arch/ia64/configs/tiger_defconfig | 2 +- arch/ia64/configs/xen_domu_defconfig | 2 +- arch/powerpc/configs/ppc64_defconfig | 2 +- arch/powerpc/configs/ppc64e_defconfig | 2 +- arch/powerpc/configs/pseries_defconfig | 2 +- arch/sh/configs/sh03_defconfig | 2 +- drivers/pci/hotplug/Kconfig | 5 +---- 9 files changed, 9 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/ia64/configs/generic_defconfig b/arch/ia64/configs/generic_defconfig index 7913695b2fc..efbd2929aeb 100644 --- a/arch/ia64/configs/generic_defconfig +++ b/arch/ia64/configs/generic_defconfig @@ -31,7 +31,7 @@ CONFIG_ACPI_FAN=m CONFIG_ACPI_DOCK=y CONFIG_ACPI_PROCESSOR=m CONFIG_ACPI_CONTAINER=m -CONFIG_HOTPLUG_PCI=m +CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_ACPI=m CONFIG_PACKET=y CONFIG_UNIX=y diff --git a/arch/ia64/configs/gensparse_defconfig b/arch/ia64/configs/gensparse_defconfig index f8e91336542..f64980dd20c 100644 --- a/arch/ia64/configs/gensparse_defconfig +++ b/arch/ia64/configs/gensparse_defconfig @@ -25,7 +25,7 @@ CONFIG_ACPI_BUTTON=m CONFIG_ACPI_FAN=m CONFIG_ACPI_PROCESSOR=m CONFIG_ACPI_CONTAINER=m -CONFIG_HOTPLUG_PCI=m +CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_ACPI=m CONFIG_PACKET=y CONFIG_UNIX=y diff --git a/arch/ia64/configs/tiger_defconfig b/arch/ia64/configs/tiger_defconfig index a5a9e02e60a..0f4e9e41f13 100644 --- a/arch/ia64/configs/tiger_defconfig +++ b/arch/ia64/configs/tiger_defconfig @@ -31,7 +31,7 @@ CONFIG_ACPI_BUTTON=m CONFIG_ACPI_FAN=m CONFIG_ACPI_PROCESSOR=m CONFIG_ACPI_CONTAINER=m -CONFIG_HOTPLUG_PCI=m +CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_ACPI=m CONFIG_PACKET=y CONFIG_UNIX=y diff --git a/arch/ia64/configs/xen_domu_defconfig b/arch/ia64/configs/xen_domu_defconfig index 37b9b422caa..b025acfde5c 100644 --- a/arch/ia64/configs/xen_domu_defconfig +++ b/arch/ia64/configs/xen_domu_defconfig @@ -32,7 +32,7 @@ CONFIG_ACPI_BUTTON=m CONFIG_ACPI_FAN=m CONFIG_ACPI_PROCESSOR=m CONFIG_ACPI_CONTAINER=m -CONFIG_HOTPLUG_PCI=m +CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_ACPI=m CONFIG_PACKET=y CONFIG_UNIX=y diff --git a/arch/powerpc/configs/ppc64_defconfig b/arch/powerpc/configs/ppc64_defconfig index c86fcb92358..0e8cfd09da2 100644 --- a/arch/powerpc/configs/ppc64_defconfig +++ b/arch/powerpc/configs/ppc64_defconfig @@ -58,7 +58,7 @@ CONFIG_SCHED_SMT=y CONFIG_PPC_DENORMALISATION=y CONFIG_PCCARD=y CONFIG_ELECTRA_CF=y -CONFIG_HOTPLUG_PCI=m +CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_RPA=m CONFIG_HOTPLUG_PCI_RPA_DLPAR=m CONFIG_PACKET=y diff --git a/arch/powerpc/configs/ppc64e_defconfig b/arch/powerpc/configs/ppc64e_defconfig index 4b20f76172e..0085dc4642c 100644 --- a/arch/powerpc/configs/ppc64e_defconfig +++ b/arch/powerpc/configs/ppc64e_defconfig @@ -32,7 +32,7 @@ CONFIG_IRQ_ALL_CPUS=y CONFIG_SPARSEMEM_MANUAL=y CONFIG_PCI_MSI=y CONFIG_PCCARD=y -CONFIG_HOTPLUG_PCI=m +CONFIG_HOTPLUG_PCI=y CONFIG_PACKET=y CONFIG_UNIX=y CONFIG_XFRM_USER=m diff --git a/arch/powerpc/configs/pseries_defconfig b/arch/powerpc/configs/pseries_defconfig index bea8587c3af..1d4b9763895 100644 --- a/arch/powerpc/configs/pseries_defconfig +++ b/arch/powerpc/configs/pseries_defconfig @@ -53,7 +53,7 @@ CONFIG_PPC_64K_PAGES=y CONFIG_PPC_SUBPAGE_PROT=y CONFIG_SCHED_SMT=y CONFIG_PPC_DENORMALISATION=y -CONFIG_HOTPLUG_PCI=m +CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_RPA=m CONFIG_HOTPLUG_PCI_RPA_DLPAR=m CONFIG_PACKET=y diff --git a/arch/sh/configs/sh03_defconfig b/arch/sh/configs/sh03_defconfig index 2051821724c..0cf4097b71e 100644 --- a/arch/sh/configs/sh03_defconfig +++ b/arch/sh/configs/sh03_defconfig @@ -22,7 +22,7 @@ CONFIG_PREEMPT=y CONFIG_CMDLINE_OVERWRITE=y CONFIG_CMDLINE="console=ttySC1,115200 mem=64M root=/dev/nfs" CONFIG_PCI=y -CONFIG_HOTPLUG_PCI=m +CONFIG_HOTPLUG_PCI=y CONFIG_BINFMT_MISC=y CONFIG_NET=y CONFIG_PACKET=y diff --git a/drivers/pci/hotplug/Kconfig b/drivers/pci/hotplug/Kconfig index bb7ebb22db0..d85009de713 100644 --- a/drivers/pci/hotplug/Kconfig +++ b/drivers/pci/hotplug/Kconfig @@ -3,16 +3,13 @@ # menuconfig HOTPLUG_PCI - tristate "Support for PCI Hotplug" + bool "Support for PCI Hotplug" depends on PCI && SYSFS ---help--- Say Y here if you have a motherboard with a PCI Hotplug controller. This allows you to add and remove PCI cards while the machine is powered up and running. - To compile this driver as a module, choose M here: the - module will be called pci_hotplug. - When in doubt, say N. if HOTPLUG_PCI -- cgit v1.2.3-70-g09d2 From 8fbac214e5c594a0c2fe78c14adf2cdbb1febc92 Mon Sep 17 00:00:00 2001 From: Mark Rutland Date: Thu, 18 Jul 2013 17:20:33 +0100 Subject: ARM: 7787/1: virt: ensure visibility of __boot_cpu_mode Secondary CPUs write to __boot_cpu_mode with caches disabled, and thus a cached value of __boot_cpu_mode may be incoherent with that in memory. This could lead to a failure to detect mismatched boot modes. This patch adds flushing to ensure that writes by secondaries to __boot_cpu_mode are made visible before we test against it. Signed-off-by: Mark Rutland Acked-by: Dave Martin Acked-by: Marc Zyngier Cc: Christoffer Dall Signed-off-by: Russell King --- arch/arm/include/asm/virt.h | 12 ++++++++++++ arch/arm/kernel/setup.c | 2 ++ 2 files changed, 14 insertions(+) (limited to 'arch') diff --git a/arch/arm/include/asm/virt.h b/arch/arm/include/asm/virt.h index 50af92bac73..4371f45c578 100644 --- a/arch/arm/include/asm/virt.h +++ b/arch/arm/include/asm/virt.h @@ -29,6 +29,7 @@ #define BOOT_CPU_MODE_MISMATCH PSR_N_BIT #ifndef __ASSEMBLY__ +#include #ifdef CONFIG_ARM_VIRT_EXT /* @@ -41,10 +42,21 @@ */ extern int __boot_cpu_mode; +static inline void sync_boot_mode(void) +{ + /* + * As secondaries write to __boot_cpu_mode with caches disabled, we + * must flush the corresponding cache entries to ensure the visibility + * of their writes. + */ + sync_cache_r(&__boot_cpu_mode); +} + void __hyp_set_vectors(unsigned long phys_vector_base); unsigned long __hyp_get_vectors(void); #else #define __boot_cpu_mode (SVC_MODE) +#define sync_boot_mode() #endif #ifndef ZIMAGE diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index 96286cb383b..afc2489ee13 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -836,6 +836,8 @@ static int __init meminfo_cmp(const void *_a, const void *_b) void __init hyp_mode_check(void) { #ifdef CONFIG_ARM_VIRT_EXT + sync_boot_mode(); + if (is_hyp_mode_available()) { pr_info("CPU: All CPU(s) started in HYP mode.\n"); pr_info("CPU: Virtualization extensions available.\n"); -- cgit v1.2.3-70-g09d2 From 1f49856bb029779d8f1b63517a3a3b34ffe672c7 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Tue, 23 Jul 2013 15:13:06 +0100 Subject: ARM: 7789/1: Do not run dummy_flush_tlb_a15_erratum() on non-Cortex-A15 Commit 93dc688 (ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)) causes the following undefined instruction error on a mx53 (Cortex-A8): Internal error: Oops - undefined instruction: 0 [#1] SMP ARM CPU: 0 PID: 275 Comm: modprobe Not tainted 3.11.0-rc2-next-20130722-00009-g9b0f371 #881 task: df46cc00 ti: df48e000 task.ti: df48e000 PC is at check_and_switch_context+0x17c/0x4d0 LR is at check_and_switch_context+0xdc/0x4d0 This problem happens because check_and_switch_context() calls dummy_flush_tlb_a15_erratum() without checking if we are really running on a Cortex-A15 or not. To avoid this issue, only call dummy_flush_tlb_a15_erratum() inside check_and_switch_context() if erratum_a15_798181() returns true, which means that we are really running on a Cortex-A15. Signed-off-by: Fabio Estevam Acked-by: Catalin Marinas Reviewed-by: Roger Quadros Signed-off-by: Russell King --- arch/arm/include/asm/tlbflush.h | 16 ++++++++++++++++ arch/arm/kernel/smp_tlb.c | 17 ----------------- arch/arm/mm/context.c | 3 ++- 3 files changed, 18 insertions(+), 18 deletions(-) (limited to 'arch') diff --git a/arch/arm/include/asm/tlbflush.h b/arch/arm/include/asm/tlbflush.h index fdbb9e36974..f467e9b3f8d 100644 --- a/arch/arm/include/asm/tlbflush.h +++ b/arch/arm/include/asm/tlbflush.h @@ -443,7 +443,18 @@ static inline void local_flush_bp_all(void) isb(); } +#include #ifdef CONFIG_ARM_ERRATA_798181 +static inline int erratum_a15_798181(void) +{ + unsigned int midr = read_cpuid_id(); + + /* Cortex-A15 r0p0..r3p2 affected */ + if ((midr & 0xff0ffff0) != 0x410fc0f0 || midr > 0x413fc0f2) + return 0; + return 1; +} + static inline void dummy_flush_tlb_a15_erratum(void) { /* @@ -453,6 +464,11 @@ static inline void dummy_flush_tlb_a15_erratum(void) dsb(); } #else +static inline int erratum_a15_798181(void) +{ + return 0; +} + static inline void dummy_flush_tlb_a15_erratum(void) { } diff --git a/arch/arm/kernel/smp_tlb.c b/arch/arm/kernel/smp_tlb.c index a98b62dca2f..c2edfff573c 100644 --- a/arch/arm/kernel/smp_tlb.c +++ b/arch/arm/kernel/smp_tlb.c @@ -70,23 +70,6 @@ static inline void ipi_flush_bp_all(void *ignored) local_flush_bp_all(); } -#ifdef CONFIG_ARM_ERRATA_798181 -static int erratum_a15_798181(void) -{ - unsigned int midr = read_cpuid_id(); - - /* Cortex-A15 r0p0..r3p2 affected */ - if ((midr & 0xff0ffff0) != 0x410fc0f0 || midr > 0x413fc0f2) - return 0; - return 1; -} -#else -static int erratum_a15_798181(void) -{ - return 0; -} -#endif - static void ipi_flush_tlb_a15_erratum(void *arg) { dmb(); diff --git a/arch/arm/mm/context.c b/arch/arm/mm/context.c index b55b1015724..4a0544492f1 100644 --- a/arch/arm/mm/context.c +++ b/arch/arm/mm/context.c @@ -245,7 +245,8 @@ void check_and_switch_context(struct mm_struct *mm, struct task_struct *tsk) if (cpumask_test_and_clear_cpu(cpu, &tlb_flush_pending)) { local_flush_bp_all(); local_flush_tlb_all(); - dummy_flush_tlb_a15_erratum(); + if (erratum_a15_798181()) + dummy_flush_tlb_a15_erratum(); } atomic64_set(&per_cpu(active_asids, cpu), asid); -- cgit v1.2.3-70-g09d2 From bdae73cd374e28db544fdd9b77de689a36e3c129 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Tue, 23 Jul 2013 16:15:36 +0100 Subject: ARM: 7790/1: Fix deferred mm switch on VIVT processors As of commit b9d4d42ad9 (ARM: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW on pre-ARMv6 CPUs), the mm switching on VIVT processors is done in the finish_arch_post_lock_switch() function to avoid whole cache flushing with interrupts disabled. The need for deferred mm switch is stored as a thread flag (TIF_SWITCH_MM). However, with preemption enabled, we can have another thread switch before finish_arch_post_lock_switch(). If the new thread has the same mm as the previous 'next' thread, the scheduler will not call switch_mm() and the TIF_SWITCH_MM flag won't be set for the new thread. This patch moves the switch pending flag to the mm_context_t structure since this is specific to the mm rather than thread. Signed-off-by: Catalin Marinas Reported-by: Marc Kleine-Budde Tested-by: Marc Kleine-Budde Cc: # 3.5+ Signed-off-by: Russell King --- arch/arm/include/asm/mmu.h | 2 ++ arch/arm/include/asm/mmu_context.h | 20 ++++++++++++++++---- arch/arm/include/asm/thread_info.h | 1 - 3 files changed, 18 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/arm/include/asm/mmu.h b/arch/arm/include/asm/mmu.h index e3d55547e75..d1b4998e4f4 100644 --- a/arch/arm/include/asm/mmu.h +++ b/arch/arm/include/asm/mmu.h @@ -6,6 +6,8 @@ typedef struct { #ifdef CONFIG_CPU_HAS_ASID atomic64_t id; +#else + int switch_pending; #endif unsigned int vmalloc_seq; } mm_context_t; diff --git a/arch/arm/include/asm/mmu_context.h b/arch/arm/include/asm/mmu_context.h index b5792b7fd8d..9b32f76bb0d 100644 --- a/arch/arm/include/asm/mmu_context.h +++ b/arch/arm/include/asm/mmu_context.h @@ -56,7 +56,7 @@ static inline void check_and_switch_context(struct mm_struct *mm, * on non-ASID CPUs, the old mm will remain valid until the * finish_arch_post_lock_switch() call. */ - set_ti_thread_flag(task_thread_info(tsk), TIF_SWITCH_MM); + mm->context.switch_pending = 1; else cpu_switch_mm(mm->pgd, mm); } @@ -65,9 +65,21 @@ static inline void check_and_switch_context(struct mm_struct *mm, finish_arch_post_lock_switch static inline void finish_arch_post_lock_switch(void) { - if (test_and_clear_thread_flag(TIF_SWITCH_MM)) { - struct mm_struct *mm = current->mm; - cpu_switch_mm(mm->pgd, mm); + struct mm_struct *mm = current->mm; + + if (mm && mm->context.switch_pending) { + /* + * Preemption must be disabled during cpu_switch_mm() as we + * have some stateful cache flush implementations. Check + * switch_pending again in case we were preempted and the + * switch to this mm was already done. + */ + preempt_disable(); + if (mm->context.switch_pending) { + mm->context.switch_pending = 0; + cpu_switch_mm(mm->pgd, mm); + } + preempt_enable_no_resched(); } } diff --git a/arch/arm/include/asm/thread_info.h b/arch/arm/include/asm/thread_info.h index 214d4158089..2b8114fcba0 100644 --- a/arch/arm/include/asm/thread_info.h +++ b/arch/arm/include/asm/thread_info.h @@ -156,7 +156,6 @@ extern int vfp_restore_user_hwstate(struct user_vfp __user *, #define TIF_USING_IWMMXT 17 #define TIF_MEMDIE 18 /* is terminating due to OOM killer */ #define TIF_RESTORE_SIGMASK 20 -#define TIF_SWITCH_MM 22 /* deferred switch_mm */ #define _TIF_SIGPENDING (1 << TIF_SIGPENDING) #define _TIF_NEED_RESCHED (1 << TIF_NEED_RESCHED) -- cgit v1.2.3-70-g09d2 From acfdd4b1f7590d02e9bae3b73bdbbc4a31b05d38 Mon Sep 17 00:00:00 2001 From: Will Deacon Date: Thu, 25 Jul 2013 11:44:48 +0100 Subject: ARM: 7791/1: a.out: remove partial a.out support a.out support on ARM requires that argc, argv and envp are passed in r0-r2 respectively, which requires hacking load_aout_binary to prevent argc being clobbered by the return code. Whilst mainline kernels do set the registers up in start_thread, the aout loader has never carried the hack in mainline. Initialising the registers in this way actually goes against the libc expectations for ELF binaries, where argc, argv and envp are passed on the stack, with r0 being used to hold a pointer to an exit function for cleaning up after the dynamic linker if required. If the pointer is NULL, then it is ignored. When execing an ELF binary, Linux currently zeroes r0, then sets it to argc and then finally clobbers it with the return value of the execve syscall, so we actually end up with: r0 = 0 stack[0] = argc r1 = stack[1] = argv r2 = stack[2] = envp libc treats r1 and r2 as undefined. The clobbering of r0 by sys_execve works for user-spawned threads, but when executing an ELF binary from a kernel thread (via call_usermodehelper), the execve is performed on the ret_from_fork path, which restores r0 from the saved pt_regs, resulting in argc being presented to the C library. This has horrible consequences when the application exits, since we have an exit function registered using argc, resulting in a jump to hyperspace. This patch solves the problem by removing the partial a.out support from arch/arm/ altogether. Cc: Cc: Ashish Sangwan Signed-off-by: Will Deacon Signed-off-by: Russell King --- arch/arm/Kconfig | 1 - arch/arm/include/asm/a.out-core.h | 45 --------------------------------------- arch/arm/include/asm/processor.h | 4 ---- arch/arm/include/uapi/asm/Kbuild | 1 - arch/arm/include/uapi/asm/a.out.h | 34 ----------------------------- 5 files changed, 85 deletions(-) delete mode 100644 arch/arm/include/asm/a.out-core.h delete mode 100644 arch/arm/include/uapi/asm/a.out.h (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index ba412e02ec0..82f069829ac 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -20,7 +20,6 @@ config ARM select GENERIC_STRNCPY_FROM_USER select GENERIC_STRNLEN_USER select HARDIRQS_SW_RESEND - select HAVE_AOUT select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL select HAVE_ARCH_KGDB select HAVE_ARCH_SECCOMP_FILTER diff --git a/arch/arm/include/asm/a.out-core.h b/arch/arm/include/asm/a.out-core.h deleted file mode 100644 index 92f10cb5c70..00000000000 --- a/arch/arm/include/asm/a.out-core.h +++ /dev/null @@ -1,45 +0,0 @@ -/* a.out coredump register dumper - * - * Copyright (C) 2007 Red Hat, Inc. All Rights Reserved. - * Written by David Howells (dhowells@redhat.com) - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public Licence - * as published by the Free Software Foundation; either version - * 2 of the Licence, or (at your option) any later version. - */ - -#ifndef _ASM_A_OUT_CORE_H -#define _ASM_A_OUT_CORE_H - -#ifdef __KERNEL__ - -#include -#include - -/* - * fill in the user structure for an a.out core dump - */ -static inline void aout_dump_thread(struct pt_regs *regs, struct user *dump) -{ - struct task_struct *tsk = current; - - dump->magic = CMAGIC; - dump->start_code = tsk->mm->start_code; - dump->start_stack = regs->ARM_sp & ~(PAGE_SIZE - 1); - - dump->u_tsize = (tsk->mm->end_code - tsk->mm->start_code) >> PAGE_SHIFT; - dump->u_dsize = (tsk->mm->brk - tsk->mm->start_data + PAGE_SIZE - 1) >> PAGE_SHIFT; - dump->u_ssize = 0; - - memset(dump->u_debugreg, 0, sizeof(dump->u_debugreg)); - - if (dump->start_stack < 0x04000000) - dump->u_ssize = (0x04000000 - dump->start_stack) >> PAGE_SHIFT; - - dump->regs = *regs; - dump->u_fpvalid = dump_fpu (regs, &dump->u_fp); -} - -#endif /* __KERNEL__ */ -#endif /* _ASM_A_OUT_CORE_H */ diff --git a/arch/arm/include/asm/processor.h b/arch/arm/include/asm/processor.h index 06e7d509eaa..413f3876341 100644 --- a/arch/arm/include/asm/processor.h +++ b/arch/arm/include/asm/processor.h @@ -54,7 +54,6 @@ struct thread_struct { #define start_thread(regs,pc,sp) \ ({ \ - unsigned long *stack = (unsigned long *)sp; \ memset(regs->uregs, 0, sizeof(regs->uregs)); \ if (current->personality & ADDR_LIMIT_32BIT) \ regs->ARM_cpsr = USR_MODE; \ @@ -65,9 +64,6 @@ struct thread_struct { regs->ARM_cpsr |= PSR_ENDSTATE; \ regs->ARM_pc = pc & ~1; /* pc */ \ regs->ARM_sp = sp; /* sp */ \ - regs->ARM_r2 = stack[2]; /* r2 (envp) */ \ - regs->ARM_r1 = stack[1]; /* r1 (argv) */ \ - regs->ARM_r0 = stack[0]; /* r0 (argc) */ \ nommu_start_thread(regs); \ }) diff --git a/arch/arm/include/uapi/asm/Kbuild b/arch/arm/include/uapi/asm/Kbuild index 47bcb2d254a..18d76fd5a2a 100644 --- a/arch/arm/include/uapi/asm/Kbuild +++ b/arch/arm/include/uapi/asm/Kbuild @@ -1,7 +1,6 @@ # UAPI Header export list include include/uapi/asm-generic/Kbuild.asm -header-y += a.out.h header-y += byteorder.h header-y += fcntl.h header-y += hwcap.h diff --git a/arch/arm/include/uapi/asm/a.out.h b/arch/arm/include/uapi/asm/a.out.h deleted file mode 100644 index 083894b2e3b..00000000000 --- a/arch/arm/include/uapi/asm/a.out.h +++ /dev/null @@ -1,34 +0,0 @@ -#ifndef __ARM_A_OUT_H__ -#define __ARM_A_OUT_H__ - -#include -#include - -struct exec -{ - __u32 a_info; /* Use macros N_MAGIC, etc for access */ - __u32 a_text; /* length of text, in bytes */ - __u32 a_data; /* length of data, in bytes */ - __u32 a_bss; /* length of uninitialized data area for file, in bytes */ - __u32 a_syms; /* length of symbol table data in file, in bytes */ - __u32 a_entry; /* start address */ - __u32 a_trsize; /* length of relocation info for text, in bytes */ - __u32 a_drsize; /* length of relocation info for data, in bytes */ -}; - -/* - * This is always the same - */ -#define N_TXTADDR(a) (0x00008000) - -#define N_TRSIZE(a) ((a).a_trsize) -#define N_DRSIZE(a) ((a).a_drsize) -#define N_SYMSIZE(a) ((a).a_syms) - -#define M_ARM 103 - -#ifndef LIBRARY_START_TEXT -#define LIBRARY_START_TEXT (0x00c00000) -#endif - -#endif /* __A_OUT_GNU_H__ */ -- cgit v1.2.3-70-g09d2 From 8e2872ce7b9a06b951680d196e893f5c0d6a3229 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Thu, 18 Jul 2013 15:18:24 +0200 Subject: s390: add support for LZ4-compressed kernel Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/Kconfig | 1 + arch/s390/boot/compressed/Makefile | 9 ++++++--- arch/s390/boot/compressed/misc.c | 4 ++++ 3 files changed, 11 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/s390/Kconfig b/arch/s390/Kconfig index 22f75b504f7..5a4c668676b 100644 --- a/arch/s390/Kconfig +++ b/arch/s390/Kconfig @@ -118,6 +118,7 @@ config S390 select HAVE_FUNCTION_TRACE_MCOUNT_TEST select HAVE_KERNEL_BZIP2 select HAVE_KERNEL_GZIP + select HAVE_KERNEL_LZ4 select HAVE_KERNEL_LZMA select HAVE_KERNEL_LZO select HAVE_KERNEL_XZ diff --git a/arch/s390/boot/compressed/Makefile b/arch/s390/boot/compressed/Makefile index 3ad8f61c998..866ecbe670e 100644 --- a/arch/s390/boot/compressed/Makefile +++ b/arch/s390/boot/compressed/Makefile @@ -6,9 +6,9 @@ BITS := $(if $(CONFIG_64BIT),64,31) -targets := vmlinux.lds vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 \ - vmlinux.bin.xz vmlinux.bin.lzma vmlinux.bin.lzo misc.o piggy.o \ - sizes.h head$(BITS).o +targets := vmlinux.lds vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 +targets += vmlinux.bin.xz vmlinux.bin.lzma vmlinux.bin.lzo vmlinux.bin.lz4 +targets += misc.o piggy.o sizes.h head$(BITS).o KBUILD_CFLAGS := -m$(BITS) -D__KERNEL__ $(LINUX_INCLUDE) -O2 KBUILD_CFLAGS += -DDISABLE_BRANCH_PROFILING @@ -48,6 +48,7 @@ vmlinux.bin.all-y := $(obj)/vmlinux.bin suffix-$(CONFIG_KERNEL_GZIP) := gz suffix-$(CONFIG_KERNEL_BZIP2) := bz2 +suffix-$(CONFIG_KERNEL_LZ4) := lz4 suffix-$(CONFIG_KERNEL_LZMA) := lzma suffix-$(CONFIG_KERNEL_LZO) := lzo suffix-$(CONFIG_KERNEL_XZ) := xz @@ -56,6 +57,8 @@ $(obj)/vmlinux.bin.gz: $(vmlinux.bin.all-y) $(call if_changed,gzip) $(obj)/vmlinux.bin.bz2: $(vmlinux.bin.all-y) $(call if_changed,bzip2) +$(obj)/vmlinux.bin.lz4: $(vmlinux.bin.all-y) + $(call if_changed,lz4) $(obj)/vmlinux.bin.lzma: $(vmlinux.bin.all-y) $(call if_changed,lzma) $(obj)/vmlinux.bin.lzo: $(vmlinux.bin.all-y) diff --git a/arch/s390/boot/compressed/misc.c b/arch/s390/boot/compressed/misc.c index c4c6a1cf221..57cbaff1f39 100644 --- a/arch/s390/boot/compressed/misc.c +++ b/arch/s390/boot/compressed/misc.c @@ -47,6 +47,10 @@ static unsigned long free_mem_end_ptr; #include "../../../../lib/decompress_bunzip2.c" #endif +#ifdef CONFIG_KERNEL_LZ4 +#include "../../../../lib/decompress_unlz4.c" +#endif + #ifdef CONFIG_KERNEL_LZMA #include "../../../../lib/decompress_unlzma.c" #endif -- cgit v1.2.3-70-g09d2 From 79b6f7fbd1c18154a93313712ab91e413778afa6 Mon Sep 17 00:00:00 2001 From: Chen Gang Date: Tue, 23 Jul 2013 16:26:08 +0800 Subject: s390/Kconfig: select 'TTY' when 'S390_GUEST' is enabled 'VIRTIO_CONSOLE' depends on 'TTY', so need to select 'TTY' explicitly before selecting 'VIRTIO_CONSOLE'. Otherwise randconfig can generate a config file which enables 'VIRTIO_CONSOLE' but has 'TTY' disabled. Signed-off-by: Chen Gang Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/s390/Kconfig b/arch/s390/Kconfig index 5a4c668676b..a281bd6e94d 100644 --- a/arch/s390/Kconfig +++ b/arch/s390/Kconfig @@ -710,6 +710,7 @@ config S390_GUEST def_bool y prompt "s390 support for virtio devices" depends on 64BIT + select TTY select VIRTUALIZATION select VIRTIO select VIRTIO_CONSOLE -- cgit v1.2.3-70-g09d2 From 594712276e737961d30e11eae80d403b2b3815df Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Wed, 24 Jul 2013 10:35:33 +0200 Subject: s390: add support for IBM zBC12 machine Just add the new model number where appropiate. Cc: stable@vger.kernel.org # v3.10 Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/Kconfig | 7 ++++--- arch/s390/kernel/setup.c | 1 + arch/s390/mm/init.c | 1 + arch/s390/oprofile/init.c | 2 +- 4 files changed, 7 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/s390/Kconfig b/arch/s390/Kconfig index a281bd6e94d..8a4cae78f03 100644 --- a/arch/s390/Kconfig +++ b/arch/s390/Kconfig @@ -228,11 +228,12 @@ config MARCH_Z196 not work on older machines. config MARCH_ZEC12 - bool "IBM zEC12" + bool "IBM zBC12 and zEC12" select HAVE_MARCH_ZEC12_FEATURES if 64BIT help - Select this to enable optimizations for IBM zEC12 (2827 series). The - kernel will be slightly faster but will not work on older machines. + Select this to enable optimizations for IBM zBC12 and zEC12 (2828 and + 2827 series). The kernel will be slightly faster but will not work on + older machines. endchoice diff --git a/arch/s390/kernel/setup.c b/arch/s390/kernel/setup.c index 497451ec5e2..aeed8a61fa0 100644 --- a/arch/s390/kernel/setup.c +++ b/arch/s390/kernel/setup.c @@ -994,6 +994,7 @@ static void __init setup_hwcaps(void) strcpy(elf_platform, "z196"); break; case 0x2827: + case 0x2828: strcpy(elf_platform, "zEC12"); break; } diff --git a/arch/s390/mm/init.c b/arch/s390/mm/init.c index ce36ea80e4f..ad446b0c55b 100644 --- a/arch/s390/mm/init.c +++ b/arch/s390/mm/init.c @@ -69,6 +69,7 @@ static void __init setup_zero_pages(void) order = 2; break; case 0x2827: /* zEC12 */ + case 0x2828: /* zEC12 */ default: order = 5; break; diff --git a/arch/s390/oprofile/init.c b/arch/s390/oprofile/init.c index ffeb17ce7f3..930783d2c99 100644 --- a/arch/s390/oprofile/init.c +++ b/arch/s390/oprofile/init.c @@ -440,7 +440,7 @@ static int oprofile_hwsampler_init(struct oprofile_operations *ops) switch (id.machine) { case 0x2097: case 0x2098: ops->cpu_type = "s390/z10"; break; case 0x2817: case 0x2818: ops->cpu_type = "s390/z196"; break; - case 0x2827: ops->cpu_type = "s390/zEC12"; break; + case 0x2827: case 0x2828: ops->cpu_type = "s390/zEC12"; break; default: return -ENODEV; } } -- cgit v1.2.3-70-g09d2 From 3b0040a47ad63f7147e9e7d2febb61a3b564bb90 Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Thu, 25 Jul 2013 10:18:17 +0200 Subject: s390/bitops: fix find_next_bit_left The find_next_bit_left function is broken if used with an offset which is not a multiple of 64. The shift to mask the bits of a 64-bit word not to search is in the wrong direction, the result can be either a bit found smaller than the offset or failure to find a set bit. Cc: # v3.8+ Signed-off-by: Martin Schwidefsky --- arch/s390/include/asm/bitops.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/s390/include/asm/bitops.h b/arch/s390/include/asm/bitops.h index 4d8604e311f..7d467675873 100644 --- a/arch/s390/include/asm/bitops.h +++ b/arch/s390/include/asm/bitops.h @@ -693,7 +693,7 @@ static inline int find_next_bit_left(const unsigned long *addr, size -= offset; p = addr + offset / BITS_PER_LONG; if (bit) { - set = __flo_word(0, *p & (~0UL << bit)); + set = __flo_word(0, *p & (~0UL >> bit)); if (set >= size) return size + offset; if (set < BITS_PER_LONG) -- cgit v1.2.3-70-g09d2 From 198b1bf8c3a06de42a88ad7f9d664f18d740a418 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Thu, 25 Jul 2013 11:16:48 +0200 Subject: s390/perf: fix compile error (undefined reference sie_exit) The perf_event code references sie_exit even if KVM is not available. So add proper ifdefs to fix this one: arch/s390/built-in.o: In function `sys_call_table_emu': (.rodata+0x2b98): undefined reference to `sie_exit' arch/s390/built-in.o: In function `sys_call_table_emu': (.rodata+0x2ba0): undefined reference to `sie_exit' make: *** [vmlinux] Error 1 Reported-by: Zhouping Liu Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/perf_event.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/s390/kernel/perf_event.c b/arch/s390/kernel/perf_event.c index a6fc037671b..500aa1029bc 100644 --- a/arch/s390/kernel/perf_event.c +++ b/arch/s390/kernel/perf_event.c @@ -52,12 +52,13 @@ static struct kvm_s390_sie_block *sie_block(struct pt_regs *regs) static bool is_in_guest(struct pt_regs *regs) { - unsigned long ip = instruction_pointer(regs); - if (user_mode(regs)) return false; - - return ip == (unsigned long) &sie_exit; +#if defined(CONFIG_KVM) || defined(CONFIG_KVM_MODULE) + return instruction_pointer(regs) == (unsigned long) &sie_exit; +#else + return false; +#endif } static unsigned long guest_is_user_mode(struct pt_regs *regs) -- cgit v1.2.3-70-g09d2 From 845ad05ec31e0f3872a321e10dbeaf872022632c Mon Sep 17 00:00:00 2001 From: Feng Kan Date: Tue, 23 Jul 2013 18:52:31 +0100 Subject: arm64: Change kernel stack size to 16K Written by Catalin Marinas, tested by APM on storm platform. This is needed because of the failures encountered when running SpecWeb benchmark test. Signed-off-by: Feng Kan Acked-by: Kumar Sankaran Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/thread_info.h | 4 ++-- arch/arm64/kernel/entry.S | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm64/include/asm/thread_info.h b/arch/arm64/include/asm/thread_info.h index 3659e460071..23a3c4791d8 100644 --- a/arch/arm64/include/asm/thread_info.h +++ b/arch/arm64/include/asm/thread_info.h @@ -24,10 +24,10 @@ #include #ifndef CONFIG_ARM64_64K_PAGES -#define THREAD_SIZE_ORDER 1 +#define THREAD_SIZE_ORDER 2 #endif -#define THREAD_SIZE 8192 +#define THREAD_SIZE 16384 #define THREAD_START_SP (THREAD_SIZE - 16) #ifndef __ASSEMBLY__ diff --git a/arch/arm64/kernel/entry.S b/arch/arm64/kernel/entry.S index 1d1314280a0..6ad781b21c0 100644 --- a/arch/arm64/kernel/entry.S +++ b/arch/arm64/kernel/entry.S @@ -121,7 +121,7 @@ .macro get_thread_info, rd mov \rd, sp - and \rd, \rd, #~((1 << 13) - 1) // top of 8K stack + and \rd, \rd, #~(THREAD_SIZE - 1) // top of stack .endm /* -- cgit v1.2.3-70-g09d2 From df981edcb9bce00b9c5e4f3cc33f3f98bc9a2394 Mon Sep 17 00:00:00 2001 From: Roy Franz Date: Wed, 24 Jul 2013 17:48:44 -0700 Subject: x86, efi: correct call to free_pages Specify memory size in pages, not bytes. Signed-off-by: Roy Franz Signed-off-by: Matt Fleming --- arch/x86/boot/compressed/eboot.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/boot/compressed/eboot.c b/arch/x86/boot/compressed/eboot.c index d606463aa6d..b7388a425f0 100644 --- a/arch/x86/boot/compressed/eboot.c +++ b/arch/x86/boot/compressed/eboot.c @@ -225,7 +225,7 @@ static void low_free(unsigned long size, unsigned long addr) unsigned long nr_pages; nr_pages = round_up(size, EFI_PAGE_SIZE) / EFI_PAGE_SIZE; - efi_call_phys2(sys_table->boottime->free_pages, addr, size); + efi_call_phys2(sys_table->boottime->free_pages, addr, nr_pages); } static void find_bits(unsigned long mask, u8 *pos, u8 *size) -- cgit v1.2.3-70-g09d2 From eaa5a990191d204ba0f9d35dbe5505ec2cdd1460 Mon Sep 17 00:00:00 2001 From: "H.J. Lu" Date: Fri, 26 Jul 2013 09:11:56 -0700 Subject: x86, fpu: correct the asm constraints for fxsave, unbreak mxcsr.daz MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit GCC will optimize mxcsr_feature_mask_init in arch/x86/kernel/i387.c: memset(&fx_scratch, 0, sizeof(struct i387_fxsave_struct)); asm volatile("fxsave %0" : : "m" (fx_scratch)); mask = fx_scratch.mxcsr_mask; if (mask == 0) mask = 0x0000ffbf; to memset(&fx_scratch, 0, sizeof(struct i387_fxsave_struct)); asm volatile("fxsave %0" : : "m" (fx_scratch)); mask = 0x0000ffbf; since asm statement doesn’t say it will update fx_scratch. As the result, the DAZ bit will be cleared. This patch fixes it. This bug dates back to at least kernel 2.6.12. Signed-off-by: H. Peter Anvin Cc: --- arch/x86/kernel/i387.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/i387.c b/arch/x86/kernel/i387.c index 202d24f0f7e..5d576ab3440 100644 --- a/arch/x86/kernel/i387.c +++ b/arch/x86/kernel/i387.c @@ -116,7 +116,7 @@ static void mxcsr_feature_mask_init(void) if (cpu_has_fxsr) { memset(&fx_scratch, 0, sizeof(struct i387_fxsave_struct)); - asm volatile("fxsave %0" : : "m" (fx_scratch)); + asm volatile("fxsave %0" : "+m" (fx_scratch)); mask = fx_scratch.mxcsr_mask; if (mask == 0) mask = 0x0000ffbf; -- cgit v1.2.3-70-g09d2 From 8fd62389a778c902c7e8532594ea924bbaf465e8 Mon Sep 17 00:00:00 2001 From: Rohit Vaswani Date: Tue, 18 Jun 2013 18:53:33 -0700 Subject: ARM: msm: Consolidate gpiomux for older architectures Msm gpiomux can be used only for 7x30 and 8x50. Prevent compilation and fix build issues on 7X00, 8X60 and 8960. Signed-off-by: Rohit Vaswani Signed-off-by: David Brown --- arch/arm/mach-msm/Kconfig | 3 +-- arch/arm/mach-msm/gpiomux-v1.c | 33 --------------------------------- arch/arm/mach-msm/gpiomux.h | 10 ---------- 3 files changed, 1 insertion(+), 45 deletions(-) delete mode 100644 arch/arm/mach-msm/gpiomux-v1.c (limited to 'arch') diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig index 614e41e7881..905efc8cac7 100644 --- a/arch/arm/mach-msm/Kconfig +++ b/arch/arm/mach-msm/Kconfig @@ -121,8 +121,7 @@ config MSM_SMD bool config MSM_GPIOMUX - depends on !(ARCH_MSM8X60 || ARCH_MSM8960) - bool "MSM V1 TLMM GPIOMUX architecture" + bool help Support for MSM V1 TLMM GPIOMUX architecture. diff --git a/arch/arm/mach-msm/gpiomux-v1.c b/arch/arm/mach-msm/gpiomux-v1.c deleted file mode 100644 index 27de2abd714..00000000000 --- a/arch/arm/mach-msm/gpiomux-v1.c +++ /dev/null @@ -1,33 +0,0 @@ -/* Copyright (c) 2010, Code Aurora Forum. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA - * 02110-1301, USA. - */ -#include -#include "gpiomux.h" -#include "proc_comm.h" - -void __msm_gpiomux_write(unsigned gpio, gpiomux_config_t val) -{ - unsigned tlmm_config = (val & ~GPIOMUX_CTL_MASK) | - ((gpio & 0x3ff) << 4); - unsigned tlmm_disable = 0; - int rc; - - rc = msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, - &tlmm_config, &tlmm_disable); - if (rc) - pr_err("%s: unexpected proc_comm failure %d: %08x %08x\n", - __func__, rc, tlmm_config, tlmm_disable); -} diff --git a/arch/arm/mach-msm/gpiomux.h b/arch/arm/mach-msm/gpiomux.h index 8e82f41a892..4410d7766f9 100644 --- a/arch/arm/mach-msm/gpiomux.h +++ b/arch/arm/mach-msm/gpiomux.h @@ -73,16 +73,6 @@ extern struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS]; int msm_gpiomux_write(unsigned gpio, gpiomux_config_t active, gpiomux_config_t suspended); - -/* Architecture-internal function for use by the framework only. - * This function can assume the following: - * - the gpio value has passed a bounds-check - * - the gpiomux spinlock has been obtained - * - * This function is not for public consumption. External users - * should use msm_gpiomux_write. - */ -void __msm_gpiomux_write(unsigned gpio, gpiomux_config_t val); #else static inline int msm_gpiomux_write(unsigned gpio, gpiomux_config_t active, -- cgit v1.2.3-70-g09d2 From 4ffd9e2c4deda2ad90ce261174b2bc90e0660703 Mon Sep 17 00:00:00 2001 From: Vineet Gupta Date: Fri, 26 Jul 2013 15:29:40 -0700 Subject: ARC: SMP build breakage Signed-off-by: Vineet Gupta --- arch/arc/include/asm/entry.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arc/include/asm/entry.h b/arch/arc/include/asm/entry.h index 8943c028d4b..df57611652e 100644 --- a/arch/arc/include/asm/entry.h +++ b/arch/arc/include/asm/entry.h @@ -38,6 +38,7 @@ #include #include /* For VMALLOC_START */ #include /* For THREAD_SIZE */ +#include /* Note on the LD/ST addr modes with addr reg wback * -- cgit v1.2.3-70-g09d2 From 6eddacae385052c7a1f4f60ffdf0eeec88088ad0 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 27 Jul 2013 00:45:45 +0100 Subject: ARM: Fix sorting of machine- initializers So, there's a comment I put at the top of this, which people seem to fail to read. So let's fix it for them instead. Signed-off-by: Russell King --- arch/arm/Makefile | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/arm/Makefile b/arch/arm/Makefile index c0ac0f5e5e5..6fd2ceae305 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -153,6 +153,7 @@ machine-$(CONFIG_ARCH_DAVINCI) += davinci machine-$(CONFIG_ARCH_DOVE) += dove machine-$(CONFIG_ARCH_EBSA110) += ebsa110 machine-$(CONFIG_ARCH_EP93XX) += ep93xx +machine-$(CONFIG_ARCH_EXYNOS) += exynos machine-$(CONFIG_ARCH_GEMINI) += gemini machine-$(CONFIG_ARCH_HIGHBANK) += highbank machine-$(CONFIG_ARCH_INTEGRATOR) += integrator @@ -160,15 +161,16 @@ machine-$(CONFIG_ARCH_IOP13XX) += iop13xx machine-$(CONFIG_ARCH_IOP32X) += iop32x machine-$(CONFIG_ARCH_IOP33X) += iop33x machine-$(CONFIG_ARCH_IXP4XX) += ixp4xx +machine-$(CONFIG_ARCH_KEYSTONE) += keystone machine-$(CONFIG_ARCH_KIRKWOOD) += kirkwood machine-$(CONFIG_ARCH_KS8695) += ks8695 machine-$(CONFIG_ARCH_LPC32XX) += lpc32xx machine-$(CONFIG_ARCH_MMP) += mmp machine-$(CONFIG_ARCH_MSM) += msm machine-$(CONFIG_ARCH_MV78XX0) += mv78xx0 +machine-$(CONFIG_ARCH_MVEBU) += mvebu machine-$(CONFIG_ARCH_MXC) += imx machine-$(CONFIG_ARCH_MXS) += mxs -machine-$(CONFIG_ARCH_MVEBU) += mvebu machine-$(CONFIG_ARCH_NETX) += netx machine-$(CONFIG_ARCH_NOMADIK) += nomadik machine-$(CONFIG_ARCH_NSPIRE) += nspire @@ -176,7 +178,6 @@ machine-$(CONFIG_ARCH_OMAP1) += omap1 machine-$(CONFIG_ARCH_OMAP2PLUS) += omap2 machine-$(CONFIG_ARCH_ORION5X) += orion5x machine-$(CONFIG_ARCH_PICOXCELL) += picoxcell -machine-$(CONFIG_ARCH_SIRF) += prima2 machine-$(CONFIG_ARCH_PXA) += pxa machine-$(CONFIG_ARCH_REALVIEW) += realview machine-$(CONFIG_ARCH_ROCKCHIP) += rockchip @@ -186,25 +187,24 @@ machine-$(CONFIG_ARCH_S3C64XX) += s3c64xx machine-$(CONFIG_ARCH_S5P64X0) += s5p64x0 machine-$(CONFIG_ARCH_S5PC100) += s5pc100 machine-$(CONFIG_ARCH_S5PV210) += s5pv210 -machine-$(CONFIG_ARCH_EXYNOS) += exynos machine-$(CONFIG_ARCH_SA1100) += sa1100 machine-$(CONFIG_ARCH_SHARK) += shark machine-$(CONFIG_ARCH_SHMOBILE) += shmobile +machine-$(CONFIG_ARCH_SIRF) += prima2 +machine-$(CONFIG_ARCH_SOCFPGA) += socfpga +machine-$(CONFIG_ARCH_STI) += sti +machine-$(CONFIG_ARCH_SUNXI) += sunxi machine-$(CONFIG_ARCH_TEGRA) += tegra machine-$(CONFIG_ARCH_U300) += u300 machine-$(CONFIG_ARCH_U8500) += ux500 machine-$(CONFIG_ARCH_VERSATILE) += versatile machine-$(CONFIG_ARCH_VEXPRESS) += vexpress +machine-$(CONFIG_ARCH_VIRT) += virt machine-$(CONFIG_ARCH_VT8500) += vt8500 machine-$(CONFIG_ARCH_W90X900) += w90x900 +machine-$(CONFIG_ARCH_ZYNQ) += zynq machine-$(CONFIG_FOOTBRIDGE) += footbridge -machine-$(CONFIG_ARCH_SOCFPGA) += socfpga machine-$(CONFIG_PLAT_SPEAR) += spear -machine-$(CONFIG_ARCH_STI) += sti -machine-$(CONFIG_ARCH_VIRT) += virt -machine-$(CONFIG_ARCH_ZYNQ) += zynq -machine-$(CONFIG_ARCH_SUNXI) += sunxi -machine-$(CONFIG_ARCH_KEYSTONE) += keystone # Platform directory name. This list is sorted alphanumerically # by CONFIG_* macro name. -- cgit v1.2.3-70-g09d2 From 2b29a9fdcb92bfc6b6f4c412d71505869de61a56 Mon Sep 17 00:00:00 2001 From: Dominik Dingel Date: Fri, 26 Jul 2013 15:04:00 +0200 Subject: KVM: s390: move kvm_guest_enter,exit closer to sie Any uaccess between guest_enter and guest_exit could trigger a page fault, the page fault handler would handle it as a guest fault and translate a user address as guest address. Signed-off-by: Dominik Dingel Signed-off-by: Christian Borntraeger CC: stable@vger.kernel.org Signed-off-by: Paolo Bonzini --- arch/s390/kvm/kvm-s390.c | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/s390/kvm/kvm-s390.c b/arch/s390/kvm/kvm-s390.c index ba694d2ba51..34c1c9a90be 100644 --- a/arch/s390/kvm/kvm-s390.c +++ b/arch/s390/kvm/kvm-s390.c @@ -702,14 +702,25 @@ static int __vcpu_run(struct kvm_vcpu *vcpu) return rc; vcpu->arch.sie_block->icptcode = 0; - preempt_disable(); - kvm_guest_enter(); - preempt_enable(); VCPU_EVENT(vcpu, 6, "entering sie flags %x", atomic_read(&vcpu->arch.sie_block->cpuflags)); trace_kvm_s390_sie_enter(vcpu, atomic_read(&vcpu->arch.sie_block->cpuflags)); + + /* + * As PF_VCPU will be used in fault handler, between guest_enter + * and guest_exit should be no uaccess. + */ + preempt_disable(); + kvm_guest_enter(); + preempt_enable(); rc = sie64a(vcpu->arch.sie_block, vcpu->run->s.regs.gprs); + kvm_guest_exit(); + + VCPU_EVENT(vcpu, 6, "exit sie icptcode %d", + vcpu->arch.sie_block->icptcode); + trace_kvm_s390_sie_exit(vcpu, vcpu->arch.sie_block->icptcode); + if (rc > 0) rc = 0; if (rc < 0) { @@ -721,10 +732,6 @@ static int __vcpu_run(struct kvm_vcpu *vcpu) rc = kvm_s390_inject_program_int(vcpu, PGM_ADDRESSING); } } - VCPU_EVENT(vcpu, 6, "exit sie icptcode %d", - vcpu->arch.sie_block->icptcode); - trace_kvm_s390_sie_exit(vcpu, vcpu->arch.sie_block->icptcode); - kvm_guest_exit(); memcpy(&vcpu->run->s.regs.gprs[14], &vcpu->arch.sie_block->gg14, 16); return rc; -- cgit v1.2.3-70-g09d2 From e769ece3b129698d2b09811a6f6d304e4eaa8c29 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Fri, 26 Jul 2013 15:04:01 +0200 Subject: KVM: s390: fix pfmf non-quiescing control handling Fix the test within handle_pfmf() if the host has the NQ key-setting facility installed. Right now the code would incorrectly generate a program check in the guest if the NQ control bit for a pfmf request was set and if the host has the NQ key-setting facility installed. Signed-off-by: Heiko Carstens Reviewed-by: Thomas Huth Signed-off-by: Christian Borntraeger Signed-off-by: Paolo Bonzini --- arch/s390/kvm/priv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/s390/kvm/priv.c b/arch/s390/kvm/priv.c index 0da3e6eb6be..4cdc54e63eb 100644 --- a/arch/s390/kvm/priv.c +++ b/arch/s390/kvm/priv.c @@ -16,6 +16,7 @@ #include #include #include +#include #include #include #include @@ -532,8 +533,7 @@ static int handle_pfmf(struct kvm_vcpu *vcpu) return kvm_s390_inject_program_int(vcpu, PGM_SPECIFICATION); /* Only provide non-quiescing support if the host supports it */ - if (vcpu->run->s.regs.gprs[reg1] & PFMF_NQ && - S390_lowcore.stfl_fac_list & 0x00020000) + if (vcpu->run->s.regs.gprs[reg1] & PFMF_NQ && !test_facility(14)) return kvm_s390_inject_program_int(vcpu, PGM_SPECIFICATION); /* No support for conditional-SSKE */ -- cgit v1.2.3-70-g09d2 From 1a7f0e3c4fff449f6dd08787beb98a8e57d8cdc7 Mon Sep 17 00:00:00 2001 From: Tony Luck Date: Wed, 24 Jul 2013 10:09:43 -0700 Subject: x86/mce: Fix mce regression from recent cleanup In commit 33d7885b594e169256daef652e8d3527b2298e75 x86/mce: Update MCE severity condition check We simplified the rules to recognise each classification of recoverable machine check combining the instruction and data fetch rules into a single entry based on clarifications in the June 2013 SDM that all recoverable events would be reported on the unaffected processor with MCG_STATUS.EIPV=0 and MCG_STATUS.RIPV=1. Unfortunately the simplified rule has a couple of bugs. Fix them here. Acked-by: Naveen N. Rao Signed-off-by: Tony Luck --- arch/x86/kernel/cpu/mcheck/mce-severity.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/cpu/mcheck/mce-severity.c b/arch/x86/kernel/cpu/mcheck/mce-severity.c index e2703520d12..c370e1c4468 100644 --- a/arch/x86/kernel/cpu/mcheck/mce-severity.c +++ b/arch/x86/kernel/cpu/mcheck/mce-severity.c @@ -111,8 +111,8 @@ static struct severity { #ifdef CONFIG_MEMORY_FAILURE MCESEV( KEEP, "Action required but unaffected thread is continuable", - SER, MASK(MCI_STATUS_OVER|MCI_UC_SAR|MCI_ADDR|MCACOD, MCI_UC_SAR|MCI_ADDR), - MCGMASK(MCG_STATUS_RIPV, MCG_STATUS_RIPV) + SER, MASK(MCI_STATUS_OVER|MCI_UC_SAR|MCI_ADDR, MCI_UC_SAR|MCI_ADDR), + MCGMASK(MCG_STATUS_RIPV|MCG_STATUS_EIPV, MCG_STATUS_RIPV) ), MCESEV( AR, "Action required: data load error in a user process", -- cgit v1.2.3-70-g09d2 From 3709d323085853dc537711154004ba8704cefb9c Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Mon, 29 Jul 2013 12:03:01 -0500 Subject: ARM: dts: omap5-uevm: document regulator signals used on the actual board MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, currently we use the Palmas regulator names which is used for different purposes on uEVM. Document the same based on 750-2628-XXX boards - which is meant to be supported by this dts. Reported-by: Marc Jüttner Signed-off-by: Nishanth Menon Acked-by: J Keerthy Acked-by: Benoit Cousson Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 08b72678abf..b430b8f884b 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -282,6 +282,7 @@ regulators { smps123_reg: smps123 { + /* VDD_OPP_MPU */ regulator-name = "smps123"; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; @@ -290,6 +291,7 @@ }; smps45_reg: smps45 { + /* VDD_OPP_MM */ regulator-name = "smps45"; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1310000>; @@ -298,6 +300,7 @@ }; smps6_reg: smps6 { + /* VDD_DDR3 - over VDD_SMPS6 */ regulator-name = "smps6"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; @@ -306,6 +309,7 @@ }; smps7_reg: smps7 { + /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ regulator-name = "smps7"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -314,6 +318,7 @@ }; smps8_reg: smps8 { + /* VDD_OPP_CORE */ regulator-name = "smps8"; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1310000>; @@ -322,6 +327,7 @@ }; smps9_reg: smps9 { + /* VDDA_2v1_AUD over VDD_2v1 */ regulator-name = "smps9"; regulator-min-microvolt = <2100000>; regulator-max-microvolt = <2100000>; @@ -331,6 +337,7 @@ }; smps10_reg: smps10 { + /* VBUS_5V_OTG */ regulator-name = "smps10"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -339,6 +346,7 @@ }; ldo1_reg: ldo1 { + /* VDDAPHY_CAM: vdda_csiport */ regulator-name = "ldo1"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; @@ -347,6 +355,7 @@ }; ldo2_reg: ldo2 { + /* VCC_2V8_DISP: Does not go anywhere */ regulator-name = "ldo2"; regulator-min-microvolt = <2900000>; regulator-max-microvolt = <2900000>; @@ -355,6 +364,7 @@ }; ldo3_reg: ldo3 { + /* VDDAPHY_MDM: vdda_lli */ regulator-name = "ldo3"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; @@ -363,6 +373,7 @@ }; ldo4_reg: ldo4 { + /* VDDAPHY_DISP: vdda_dsiport/hdmi */ regulator-name = "ldo4"; regulator-min-microvolt = <2200000>; regulator-max-microvolt = <2200000>; @@ -371,6 +382,7 @@ }; ldo5_reg: ldo5 { + /* VDDA_1V8_PHY: usb/sata/hdmi.. */ regulator-name = "ldo5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -379,6 +391,7 @@ }; ldo6_reg: ldo6 { + /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ regulator-name = "ldo6"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; @@ -387,6 +400,7 @@ }; ldo7_reg: ldo7 { + /* VDD_VPP: vpp1 */ regulator-name = "ldo7"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; @@ -395,6 +409,7 @@ }; ldo8_reg: ldo8 { + /* VDD_3v0: Does not go anywhere */ regulator-name = "ldo8"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; @@ -403,6 +418,7 @@ }; ldo9_reg: ldo9 { + /* VCC_DV_SDIO: vdds_sdcard */ regulator-name = "ldo9"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; @@ -411,6 +427,7 @@ }; ldoln_reg: ldoln { + /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ regulator-name = "ldoln"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -419,6 +436,7 @@ }; ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ regulator-name = "ldousb"; regulator-min-microvolt = <3250000>; regulator-max-microvolt = <3250000>; -- cgit v1.2.3-70-g09d2 From e18235a62a7ea737d0a3f73c76eacaaec6df3dfe Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Mon, 29 Jul 2013 12:03:02 -0500 Subject: ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, The regulator information is based on an older temporary pre-production board variant and does not reflect production board 750-2628-XXX boards. The following fixes are hence mandatory to ensure right voltage is supplied to key OMAP5 SoC voltage rails: - LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This can only be supplied at 1.5V or 1.8V and we currently supply 2.8V. To prevent any potential device damage risk, use the specified 1.5V-1.8V supply. Remove 'always-on' and 'boot-on' settings here as it is a 'on need' supply to SoC IP and is not enabled by PMIC by default at boot. - LDO3 supplies Low Latency Interface(LLI) hardware module which is a special hardware to communicate with Modem. However since uEVM is not setup by default for this communication, this should be disabled by default. Further, vdda_lli is supposed to be 1.5V and not 3V. - LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi This can only be supplied at 1.5V or 1.8V and we currently supply 2.2V. To prevent any potential device damage risk, use the specified 1.5V-1.8V supply. Remove 'always-on' and 'boot-on' settings here as it is a 'on need' supply to SoC IP and is not enabled by PMIC by default at boot. - LDO6 supplies the board specified VDDS_1V2_WKUP supply going to ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply 1.2V instead of 1.5V. - LDO7 supplies VDD_VPP which is vpp1. This is currently configured for 1.5V which as per data manual "A pulse width of 1000 ns and an amplitude of 2V is required to program each eFuse bit. Otherwise, VPP1 must not be supplied". So, fix the voltage to 2V. and disable the supply since we have no plans of programming efuse bits - it can only be done once - in factory. Further it is not enabled by default by PMIC so, 'boot-on' must be removed, and the 'always-on' needs to be removed to achieve pulsing if efuse needs to be programmed. - LDO9 supplies the board specified vdds_sdcard supply going within SoC specification of 1.8V or 3.0V. Further the supply is controlled by switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled on need basis. Reported-by: Marc Jüttner Signed-off-by: Nishanth Menon Acked-by: J Keerthy Acked-by: Benoit Cousson Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 43 +++++++++++++++++++++------------------- 1 file changed, 23 insertions(+), 20 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index b430b8f884b..247c03c0d73 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -235,7 +235,7 @@ }; &mmc1 { - vmmc-supply = <&vmmcsd_fixed>; + vmmc-supply = <&ldo9_reg>; bus-width = <4>; }; @@ -348,10 +348,8 @@ ldo1_reg: ldo1 { /* VDDAPHY_CAM: vdda_csiport */ regulator-name = "ldo1"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; }; ldo2_reg: ldo2 { @@ -366,19 +364,18 @@ ldo3_reg: ldo3 { /* VDDAPHY_MDM: vdda_lli */ regulator-name = "ldo3"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; regulator-boot-on; + /* Only if Modem is used */ + status = "disabled"; }; ldo4_reg: ldo4 { /* VDDAPHY_DISP: vdda_dsiport/hdmi */ regulator-name = "ldo4"; - regulator-min-microvolt = <2200000>; - regulator-max-microvolt = <2200000>; - regulator-always-on; - regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; }; ldo5_reg: ldo5 { @@ -393,8 +390,8 @@ ldo6_reg: ldo6 { /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ regulator-name = "ldo6"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; }; @@ -402,10 +399,10 @@ ldo7_reg: ldo7 { /* VDD_VPP: vpp1 */ regulator-name = "ldo7"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + /* Only for efuse reprograming! */ + status = "disabled"; }; ldo8_reg: ldo8 { @@ -421,8 +418,7 @@ /* VCC_DV_SDIO: vdds_sdcard */ regulator-name = "ldo9"; regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; + regulator-max-microvolt = <3000000>; regulator-boot-on; }; @@ -443,6 +439,13 @@ regulator-always-on; regulator-boot-on; }; + + regen3_reg: regen3 { + /* REGEN3 controls LDO9 supply to card */ + regulator-name = "regen3"; + regulator-always-on; + regulator-boot-on; + }; }; }; }; -- cgit v1.2.3-70-g09d2 From bd3c5544a1e98a25d2d24c98779092e0f84373f7 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Mon, 29 Jul 2013 12:03:03 -0500 Subject: ARM: dts: omap5-uevm: update optional/unused regulator configurations MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, The regulator information is based on an older temporary pre-production board variant and does not reflect production board 750-2628-XXX boards. The following optional/unused regulators can be updated: - SMPS9 supplies TWL6040 over VDDA_2v1_AUD. This regulator needs to be enabled only when audio is active. Since it does not come active by default, it does not require "always-on" or "boot-on". - LDO2 and LDO8 do not go to any peripheral or connector on the board. Further, these unused regulators should have been 2.8V for LDO2 and 3.0V for LDO8. Mark these LDOs as disabled in the dts until needed. Reported-by: Marc Jüttner Signed-off-by: Nishanth Menon Acked-by: J Keerthy Acked-by: Benoit Cousson Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 247c03c0d73..65d7b601651 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -331,8 +331,6 @@ regulator-name = "smps9"; regulator-min-microvolt = <2100000>; regulator-max-microvolt = <2100000>; - regulator-always-on; - regulator-boot-on; ti,smps-range = <0x80>; }; @@ -355,10 +353,10 @@ ldo2_reg: ldo2 { /* VCC_2V8_DISP: Does not go anywhere */ regulator-name = "ldo2"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - regulator-always-on; - regulator-boot-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + /* Unused */ + status = "disabled"; }; ldo3_reg: ldo3 { @@ -408,10 +406,11 @@ ldo8_reg: ldo8 { /* VDD_3v0: Does not go anywhere */ regulator-name = "ldo8"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; regulator-boot-on; + /* Unused */ + status = "disabled"; }; ldo9_reg: ldo9 { -- cgit v1.2.3-70-g09d2 From 7dedd346941d317b6b313de4746ad0354006e68b Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Sun, 28 Jul 2013 23:01:48 -0600 Subject: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL With commit '82702ea11ddfe0e43382e1fa5b66d807d8114916' "ARM: OMAP2+: Fix serial init for device tree based booting" stubbing out omap_serial_early_init() for Device tree based booting, there was a crash observed on AM335x based devices when hwmod does a _setup_reset() early at boot. This was rootcaused to hwmod trying to reset console uart while earlycon was using it. The way to tell hwmod not to do this is to specify the HWMOD_INIT_NO_RESET flag, which were infact set by the omap_serial_early_init() function by parsing the cmdline to identify the console device. Parsing the cmdline to identify the uart used by earlycon itself seems broken as there is nothing preventing earlycon to use a different one. This patch, instead, attempts to populate the requiste flags for hwmod based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need for cmdline parsing in the DT as well as non-DT cases to identify the uart used by earlycon. Signed-off-by: Rajendra Nayak Reported-by: Mark Jackson Reported-by: Vaibhav Bedia Tested-by: Mark Jackson Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_hwmod.h | 48 ++++++++++++++++++++++ arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c | 6 +-- arch/arm/mach-omap2/omap_hwmod_33xx_data.c | 2 +- arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 9 ++-- arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 5 +-- arch/arm/mach-omap2/omap_hwmod_54xx_data.c | 3 +- arch/arm/mach-omap2/serial.c | 11 ----- 7 files changed, 61 insertions(+), 23 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/omap_hwmod.h b/arch/arm/mach-omap2/omap_hwmod.h index aab33fd814c..8440a21fc60 100644 --- a/arch/arm/mach-omap2/omap_hwmod.h +++ b/arch/arm/mach-omap2/omap_hwmod.h @@ -95,6 +95,54 @@ extern struct omap_hwmod_sysc_fields omap_hwmod_sysc_type3; #define MODULEMODE_HWCTRL 1 #define MODULEMODE_SWCTRL 2 +#define DEBUG_OMAP2UART1_FLAGS 0 +#define DEBUG_OMAP2UART2_FLAGS 0 +#define DEBUG_OMAP2UART3_FLAGS 0 +#define DEBUG_OMAP3UART3_FLAGS 0 +#define DEBUG_OMAP3UART4_FLAGS 0 +#define DEBUG_OMAP4UART3_FLAGS 0 +#define DEBUG_OMAP4UART4_FLAGS 0 +#define DEBUG_TI81XXUART1_FLAGS 0 +#define DEBUG_TI81XXUART2_FLAGS 0 +#define DEBUG_TI81XXUART3_FLAGS 0 +#define DEBUG_AM33XXUART1_FLAGS 0 + +#define DEBUG_OMAPUART_FLAGS (HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET) + +#if defined(CONFIG_DEBUG_OMAP2UART1) +#undef DEBUG_OMAP2UART1_FLAGS +#define DEBUG_OMAP2UART1_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_OMAP2UART2) +#undef DEBUG_OMAP2UART2_FLAGS +#define DEBUG_OMAP2UART2_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_OMAP2UART3) +#undef DEBUG_OMAP2UART3_FLAGS +#define DEBUG_OMAP2UART3_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_OMAP3UART3) +#undef DEBUG_OMAP3UART3_FLAGS +#define DEBUG_OMAP3UART3_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_OMAP3UART4) +#undef DEBUG_OMAP3UART4_FLAGS +#define DEBUG_OMAP3UART4_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_OMAP4UART3) +#undef DEBUG_OMAP4UART3_FLAGS +#define DEBUG_OMAP4UART3_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_OMAP4UART4) +#undef DEBUG_OMAP4UART4_FLAGS +#define DEBUG_OMAP4UART4_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_TI81XXUART1) +#undef DEBUG_TI81XXUART1_FLAGS +#define DEBUG_TI81XXUART1_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_TI81XXUART2) +#undef DEBUG_TI81XXUART2_FLAGS +#define DEBUG_TI81XXUART2_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_TI81XXUART3) +#undef DEBUG_TI81XXUART3_FLAGS +#define DEBUG_TI81XXUART3_FLAGS DEBUG_OMAPUART_FLAGS +#elif defined(CONFIG_DEBUG_AM33XXUART1) +#undef DEBUG_AM33XXUART1_FLAGS +#define DEBUG_AM33XXUART1_FLAGS DEBUG_OMAPUART_FLAGS +#endif /** * struct omap_hwmod_mux_info - hwmod specific mux configuration diff --git a/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c b/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c index d05fc7b5456..56cebb05509 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c @@ -512,7 +512,7 @@ struct omap_hwmod omap2xxx_uart1_hwmod = { .mpu_irqs = omap2_uart1_mpu_irqs, .sdma_reqs = omap2_uart1_sdma_reqs, .main_clk = "uart1_fck", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_OMAP2UART1_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .prcm = { .omap2 = { .module_offs = CORE_MOD, @@ -532,7 +532,7 @@ struct omap_hwmod omap2xxx_uart2_hwmod = { .mpu_irqs = omap2_uart2_mpu_irqs, .sdma_reqs = omap2_uart2_sdma_reqs, .main_clk = "uart2_fck", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_OMAP2UART2_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .prcm = { .omap2 = { .module_offs = CORE_MOD, @@ -552,7 +552,7 @@ struct omap_hwmod omap2xxx_uart3_hwmod = { .mpu_irqs = omap2_uart3_mpu_irqs, .sdma_reqs = omap2_uart3_sdma_reqs, .main_clk = "uart3_fck", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_OMAP2UART3_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .prcm = { .omap2 = { .module_offs = CORE_MOD, diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c index 28bbd56346a..d4114a919df 100644 --- a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c @@ -1512,7 +1512,7 @@ static struct omap_hwmod am33xx_uart1_hwmod = { .name = "uart1", .class = &uart_class, .clkdm_name = "l4_wkup_clkdm", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_AM33XXUART1_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .main_clk = "dpll_per_m2_div4_wkupdm_ck", .prcm = { .omap4 = { diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c index f7a3df2fb57..0c3a427da54 100644 --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c @@ -490,7 +490,7 @@ static struct omap_hwmod omap3xxx_uart1_hwmod = { .mpu_irqs = omap2_uart1_mpu_irqs, .sdma_reqs = omap2_uart1_sdma_reqs, .main_clk = "uart1_fck", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_TI81XXUART1_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .prcm = { .omap2 = { .module_offs = CORE_MOD, @@ -509,7 +509,7 @@ static struct omap_hwmod omap3xxx_uart2_hwmod = { .mpu_irqs = omap2_uart2_mpu_irqs, .sdma_reqs = omap2_uart2_sdma_reqs, .main_clk = "uart2_fck", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_TI81XXUART2_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .prcm = { .omap2 = { .module_offs = CORE_MOD, @@ -528,7 +528,8 @@ static struct omap_hwmod omap3xxx_uart3_hwmod = { .mpu_irqs = omap2_uart3_mpu_irqs, .sdma_reqs = omap2_uart3_sdma_reqs, .main_clk = "uart3_fck", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_OMAP3UART3_FLAGS | DEBUG_TI81XXUART3_FLAGS | + HWMOD_SWSUP_SIDLE_ACT, .prcm = { .omap2 = { .module_offs = OMAP3430_PER_MOD, @@ -558,7 +559,7 @@ static struct omap_hwmod omap36xx_uart4_hwmod = { .mpu_irqs = uart4_mpu_irqs, .sdma_reqs = uart4_sdma_reqs, .main_clk = "uart4_fck", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_OMAP3UART4_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .prcm = { .omap2 = { .module_offs = OMAP3430_PER_MOD, diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index d04b5e60fdb..9c3b504477d 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -2858,8 +2858,7 @@ static struct omap_hwmod omap44xx_uart3_hwmod = { .name = "uart3", .class = &omap44xx_uart_hwmod_class, .clkdm_name = "l4_per_clkdm", - .flags = HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET | - HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_OMAP4UART3_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .main_clk = "func_48m_fclk", .prcm = { .omap4 = { @@ -2875,7 +2874,7 @@ static struct omap_hwmod omap44xx_uart4_hwmod = { .name = "uart4", .class = &omap44xx_uart_hwmod_class, .clkdm_name = "l4_per_clkdm", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = DEBUG_OMAP4UART4_FLAGS | HWMOD_SWSUP_SIDLE_ACT, .main_clk = "func_48m_fclk", .prcm = { .omap4 = { diff --git a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c index f37ae96b70a..3c70f5c1860 100644 --- a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c @@ -1375,7 +1375,7 @@ static struct omap_hwmod omap54xx_uart3_hwmod = { .name = "uart3", .class = &omap54xx_uart_hwmod_class, .clkdm_name = "l4per_clkdm", - .flags = HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET, + .flags = DEBUG_OMAP4UART3_FLAGS, .main_clk = "func_48m_fclk", .prcm = { .omap4 = { @@ -1391,6 +1391,7 @@ static struct omap_hwmod omap54xx_uart4_hwmod = { .name = "uart4", .class = &omap54xx_uart_hwmod_class, .clkdm_name = "l4per_clkdm", + .flags = DEBUG_OMAP4UART4_FLAGS, .main_clk = "func_48m_fclk", .prcm = { .omap4 = { diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 3a674de6cb6..a388f8c1bcb 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -208,17 +208,6 @@ static int __init omap_serial_early_init(void) pr_info("%s used as console in debug mode: uart%d clocks will not be gated", uart_name, uart->num); } - - /* - * omap-uart can be used for earlyprintk logs - * So if omap-uart is used as console then prevent - * uart reset and idle to get logs from omap-uart - * until uart console driver is available to take - * care for console messages. - * Idling or resetting omap-uart while printing logs - * early boot logs can stall the boot-up. - */ - oh->flags |= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET; } } while (1); -- cgit v1.2.3-70-g09d2 From f66e329d889fce165074f677509d449fc92ff7b9 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Sun, 28 Jul 2013 23:01:50 -0600 Subject: ARM: OMAP2+: Avoid idling memory controllers with no drivers Memory controllers in OMAP (like GPMC and EMIF) have the hwmods marked with HWMOD_INIT_NO_IDLE and are left in enabled state post initial setup. Even if they have drivers missing, avoid idling them as part of omap_device_late_idle() Signed-off-by: Rajendra Nayak Tested-by: Mark Jackson Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_device.c | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c index 5cc92874be7..1c82cdedd35 100644 --- a/arch/arm/mach-omap2/omap_device.c +++ b/arch/arm/mach-omap2/omap_device.c @@ -842,6 +842,7 @@ static int __init omap_device_late_idle(struct device *dev, void *data) { struct platform_device *pdev = to_platform_device(dev); struct omap_device *od = to_omap_device(pdev); + int i; if (!od) return 0; @@ -850,6 +851,15 @@ static int __init omap_device_late_idle(struct device *dev, void *data) * If omap_device state is enabled, but has no driver bound, * idle it. */ + + /* + * Some devices (like memory controllers) are always kept + * enabled, and should not be idled even with no drivers. + */ + for (i = 0; i < od->hwmods_cnt; i++) + if (od->hwmods[i]->flags & HWMOD_INIT_NO_IDLE) + return 0; + if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER) { if (od->_state == OMAP_DEVICE_STATE_ENABLED) { dev_warn(dev, "%s: enabled but no driver. Idling\n", -- cgit v1.2.3-70-g09d2 From 7268032dfb1180fca6e91a738380b7ac53684247 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Sun, 28 Jul 2013 23:01:51 -0600 Subject: ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state Some hwmods which are marked with HWMOD_INIT_NO_IDLE are left in enabled state post setup(). When a omap_device gets created for such hwmods make sure the omap_device and pm_runtime states are also in sync for such hwmods by doing a omap_device_enable() and pm_runtime_set_active() for the device. Signed-off-by: Rajendra Nayak Tested-by: Mark Jackson Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_device.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c index 1c82cdedd35..f99f68e1e85 100644 --- a/arch/arm/mach-omap2/omap_device.c +++ b/arch/arm/mach-omap2/omap_device.c @@ -129,6 +129,7 @@ static int omap_device_build_from_dt(struct platform_device *pdev) struct device_node *node = pdev->dev.of_node; const char *oh_name; int oh_cnt, i, ret = 0; + bool device_active = false; oh_cnt = of_property_count_strings(node, "ti,hwmods"); if (oh_cnt <= 0) { @@ -152,6 +153,8 @@ static int omap_device_build_from_dt(struct platform_device *pdev) goto odbfd_exit1; } hwmods[i] = oh; + if (oh->flags & HWMOD_INIT_NO_IDLE) + device_active = true; } od = omap_device_alloc(pdev, hwmods, oh_cnt); @@ -172,6 +175,11 @@ static int omap_device_build_from_dt(struct platform_device *pdev) pdev->dev.pm_domain = &omap_device_pm_domain; + if (device_active) { + omap_device_enable(pdev); + pm_runtime_set_active(&pdev->dev); + } + odbfd_exit1: kfree(hwmods); odbfd_exit: -- cgit v1.2.3-70-g09d2 From 130142d91467e8a07f3a863db369225a89e84d75 Mon Sep 17 00:00:00 2001 From: Afzal Mohammed Date: Fri, 5 Jul 2013 20:43:00 +0530 Subject: ARM: OMAP2+: hwmod: rt address space index for DT Address space is being removed from hwmod database and DT information in property is being used. Currently the 0th index of device address space is used to map for register target address. This is not always true, eg. cpgmac has it's sysconfig in second address space. Handle it by specifying index of device address space to be used for register target. As default value of this field would be zero with static initialization, existing behaviour of using first address space for register target while using DT would be kept as such. Signed-off-by: Afzal Mohammed Tested-by: Mugunthan V N [paul@pwsan.com: use u8 rather than int to save memory] Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_hwmod.c | 2 +- arch/arm/mach-omap2/omap_hwmod.h | 2 ++ 2 files changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index 7341eff63f5..7f4db12b145 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -2386,7 +2386,7 @@ static void __init _init_mpu_rt_base(struct omap_hwmod *oh, void *data) np = of_dev_hwmod_lookup(of_find_node_by_name(NULL, "ocp"), oh); if (np) - va_start = of_iomap(np, 0); + va_start = of_iomap(np, oh->mpu_rt_idx); } else { va_start = ioremap(mem->pa_start, mem->pa_end - mem->pa_start); } diff --git a/arch/arm/mach-omap2/omap_hwmod.h b/arch/arm/mach-omap2/omap_hwmod.h index 8440a21fc60..e1482a9b3bc 100644 --- a/arch/arm/mach-omap2/omap_hwmod.h +++ b/arch/arm/mach-omap2/omap_hwmod.h @@ -616,6 +616,7 @@ struct omap_hwmod_link { * @voltdm: pointer to voltage domain (filled in at runtime) * @dev_attr: arbitrary device attributes that can be passed to the driver * @_sysc_cache: internal-use hwmod flags + * @mpu_rt_idx: index of device address space for register target (for DT boot) * @_mpu_rt_va: cached register target start address (internal use) * @_mpu_port: cached MPU register target slave (internal use) * @opt_clks_cnt: number of @opt_clks @@ -665,6 +666,7 @@ struct omap_hwmod { struct list_head node; struct omap_hwmod_ocp_if *_mpu_port; u16 flags; + u8 mpu_rt_idx; u8 response_lat; u8 rst_lines_cnt; u8 opt_clks_cnt; -- cgit v1.2.3-70-g09d2 From 50c2a3a1518befe992f868fc1fd867bdad9776ad Mon Sep 17 00:00:00 2001 From: Afzal Mohammed Date: Fri, 5 Jul 2013 20:43:17 +0530 Subject: ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space Register target address to be used for cpgmac is the second device address space. By default, hwmod picks first address space (0th index) for register target. With removal of address space from hwmod and using DT instead, cpgmac is getting wrong address space for register target. Fix it by indicating the address space to be used for register target. Signed-off-by: Afzal Mohammed Tested-by: Mugunthan V N Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_hwmod_33xx_data.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c index d4114a919df..eb2f3b93b51 100644 --- a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c @@ -562,6 +562,7 @@ static struct omap_hwmod am33xx_cpgmac0_hwmod = { .clkdm_name = "cpsw_125mhz_clkdm", .flags = (HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY), .main_clk = "cpsw_125mhz_gclk", + .mpu_rt_idx = 1, .prcm = { .omap4 = { .clkctrl_offs = AM33XX_CM_PER_CPGMAC0_CLKCTRL_OFFSET, -- cgit v1.2.3-70-g09d2 From 7ad18dd03c426b017df12a45a56e5b36d5976afb Mon Sep 17 00:00:00 2001 From: "Steven J. Hill" Date: Wed, 3 Jul 2013 17:28:22 +0000 Subject: MIPS: Fix multiple definitions of UNCAC_BASE. Fix build error below: arch/mips/include/asm/mach-generic/spaces.h:29:0: warning: "UNCAC_BASE" redefined [enabled by default] In file included from arch/mips/include/asm/addrspace.h:13:0, from arch/mips/include/asm/barrier.h:11, from arch/mips/include/asm/bitops.h:18, from include/linux/bitops.h:22, from include/linux/kernel.h:10, from include/asm-generic/bug.h:13, from arch/mips/include/asm/bug.h:41, from include/linux/bug.h:4, from include/linux/page-flags.h:9, from kernel/bounds.c:9: arch/mips/include/asm/mach-ar7/spaces.h:20:0: note: this is the location of the previous definition Signed-off-by: Steven J. Hill Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5583/ Signed-off-by: Ralf Baechle --- arch/mips/include/asm/mach-generic/spaces.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/mips/include/asm/mach-generic/spaces.h b/arch/mips/include/asm/mach-generic/spaces.h index 5b2f2e68e57..9488fa5f886 100644 --- a/arch/mips/include/asm/mach-generic/spaces.h +++ b/arch/mips/include/asm/mach-generic/spaces.h @@ -25,8 +25,12 @@ #else #define CAC_BASE _AC(0x80000000, UL) #endif +#ifndef IO_BASE #define IO_BASE _AC(0xa0000000, UL) +#endif +#ifndef UNCAC_BASE #define UNCAC_BASE _AC(0xa0000000, UL) +#endif #ifndef MAP_BASE #ifdef CONFIG_KVM_GUEST -- cgit v1.2.3-70-g09d2 From 1d3e2d79a7d5ab56b382ea96b64c4daa9d6f0ce4 Mon Sep 17 00:00:00 2001 From: "Maciej W. Rozycki" Date: Sun, 28 Jul 2013 21:20:25 +0100 Subject: MIPS: uapi/asm/siginfo.h: Fix GCC 4.1.2 compilation It wasn't until GCC 4.3 I believe that the __SIZEOF_*__ predefined macros were added. The change below switches to the _MIPS_SZLONG macro so that compilation with e.g. GCC 4.1.2 succeeds. This is a user API header so I think this is even more important, for older userland support. The change adds an unsuccessful default too, to catch any compiler configuration oddities. Signed-off-by: Maciej W. Rozycki Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5630/ Signed-off-by: Ralf Baechle --- arch/mips/include/uapi/asm/siginfo.h | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/mips/include/uapi/asm/siginfo.h b/arch/mips/include/uapi/asm/siginfo.h index b7a23064841..88e292b7719 100644 --- a/arch/mips/include/uapi/asm/siginfo.h +++ b/arch/mips/include/uapi/asm/siginfo.h @@ -25,11 +25,12 @@ struct siginfo; /* * Careful to keep union _sifields from shifting ... */ -#if __SIZEOF_LONG__ == 4 +#if _MIPS_SZLONG == 32 #define __ARCH_SI_PREAMBLE_SIZE (3 * sizeof(int)) -#endif -#if __SIZEOF_LONG__ == 8 +#elif _MIPS_SZLONG == 64 #define __ARCH_SI_PREAMBLE_SIZE (4 * sizeof(int)) +#else +#error _MIPS_SZLONG neither 32 nor 64 #endif #include -- cgit v1.2.3-70-g09d2 From 314878d246955e0c6fff95d8ae64285fe828c785 Mon Sep 17 00:00:00 2001 From: Markos Chandras Date: Tue, 23 Jul 2013 15:40:37 +0100 Subject: MIPS: Set default CPU type for BCM47XX platforms If neither BCM47XX_SSD nor BCM47XX_BCMA is selected, then no CPU type is available leading to build problems. We fix this problem by using MIPS32r1 as the default CPU type for the BCM47XX platform. Signed-off-by: Markos Chandras Acked-by: Steven J. Hill Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5618/ Signed-off-by: Ralf Baechle --- arch/mips/Kconfig | 1 + arch/mips/bcm47xx/Kconfig | 1 - 2 files changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index c3abed33230..e12764c2a9d 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -114,6 +114,7 @@ config BCM47XX select FW_CFE select HW_HAS_PCI select IRQ_CPU + select SYS_HAS_CPU_MIPS32_R1 select NO_EXCEPT_FILL select SYS_SUPPORTS_32BIT_KERNEL select SYS_SUPPORTS_LITTLE_ENDIAN diff --git a/arch/mips/bcm47xx/Kconfig b/arch/mips/bcm47xx/Kconfig index ba611927749..2b8b118398c 100644 --- a/arch/mips/bcm47xx/Kconfig +++ b/arch/mips/bcm47xx/Kconfig @@ -2,7 +2,6 @@ if BCM47XX config BCM47XX_SSB bool "SSB Support for Broadcom BCM47XX" - select SYS_HAS_CPU_MIPS32_R1 select SSB select SSB_DRIVER_MIPS select SSB_DRIVER_EXTIF -- cgit v1.2.3-70-g09d2 From c055629b279d68c79b8776681c17a2234fecf8af Mon Sep 17 00:00:00 2001 From: Markos Chandras Date: Thu, 25 Jul 2013 16:11:28 +0100 Subject: MIPS: powertv: Fix arguments for free_reserved_area() Commit 6e7582bf35b8a5a330fd08b398ae445bac86917a "MIPS: PowerTV: use free_reserved_area() to simplify code" merged in 3.11-rc1, broke the build for the powertv defconfig with the following build error: arch/mips/powertv/asic/asic_devices.c: In function 'platform_release_memory': arch/mips/powertv/asic/asic_devices.c:533:7: error: passing argument 1 of 'free_reserved_area' makes pointer from integer without a cast [-Werror] The free_reserved_area() function expects a void * pointer for the start address and a void * pointer for the end one. Signed-off-by: Markos Chandras Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5624/ Signed-off-by: Ralf Baechle --- arch/mips/powertv/asic/asic_devices.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/mips/powertv/asic/asic_devices.c b/arch/mips/powertv/asic/asic_devices.c index 9f64c238780..0238af1ba50 100644 --- a/arch/mips/powertv/asic/asic_devices.c +++ b/arch/mips/powertv/asic/asic_devices.c @@ -529,8 +529,7 @@ EXPORT_SYMBOL(asic_resource_get); */ void platform_release_memory(void *ptr, int size) { - free_reserved_area((unsigned long)ptr, (unsigned long)(ptr + size), - -1, NULL); + free_reserved_area(ptr, ptr + size, -1, NULL); } EXPORT_SYMBOL(platform_release_memory); -- cgit v1.2.3-70-g09d2 From c4091d3fbbed922a3641e5e749655e49cc0d4dee Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Wed, 24 Jul 2013 17:12:10 +0100 Subject: MIPS: BMIPS: do not change interrupt routing depending on boot CPU Commit 4df715aa ("MIPS: BMIPS: support booting from physical CPU other than 0") changed the interupt routing when we are booting from physical CPU 0, but the settings are actually correct if we are booting from physical CPU 0 or CPU 1. Revert that specific change. Signed-off-by: Florian Fainelli Cc: linux-mips@linux-mips.org Cc: cernekee@gmail.com Cc: jogo@openwrt.org Cc: blogic@openwrt.org Patchwork: https://patchwork.linux-mips.org/patch/5622/ Signed-off-by: Ralf Baechle --- arch/mips/kernel/smp-bmips.c | 8 +------- 1 file changed, 1 insertion(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/mips/kernel/smp-bmips.c b/arch/mips/kernel/smp-bmips.c index c0bb4d59076..89417c9c6ac 100644 --- a/arch/mips/kernel/smp-bmips.c +++ b/arch/mips/kernel/smp-bmips.c @@ -79,15 +79,9 @@ static void __init bmips_smp_setup(void) * MIPS interrupts 0,1 (SW INT 0,1) cross over to the other thread * MIPS interrupt 2 (HW INT 0) is the CPU0 L1 controller output * MIPS interrupt 3 (HW INT 1) is the CPU1 L1 controller output - * - * If booting from TP1, leave the existing CMT interrupt routing - * such that TP0 responds to SW1 and TP1 responds to SW0. */ - if (boot_cpu == 0) - change_c0_brcm_cmt_intr(0xf8018000, + change_c0_brcm_cmt_intr(0xf8018000, (0x02 << 27) | (0x03 << 15)); - else - change_c0_brcm_cmt_intr(0xf8018000, (0x1d << 27)); /* single core, 2 threads (2 pipelines) */ max_cpus = 2; -- cgit v1.2.3-70-g09d2 From ff5fadaff39180dc0b652753b5614a564711be29 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Wed, 24 Jul 2013 17:12:11 +0100 Subject: MIPS: BMIPS: fix slave CPU booting when physical CPU is not 0 The current BMIPS SMP code assumes that the slave CPU is physical and logical CPU 1, but on some systems such as BCM3368, the slave CPU is physical CPU0. Fix the code to read the physical CPU (thread ID) we are running this code on, and adjust the relocation vector address based on it. This allows bringing up the second CPU on BCM3368 for instance. Signed-off-by: Florian Fainelli Cc: linux-mips@linux-mips.org Cc: cernekee@gmail.com Cc: jogo@openwrt.org Cc: blogic@openwrt.org Patchwork: https://patchwork.linux-mips.org/patch/5621/ Signed-off-by: Ralf Baechle --- arch/mips/kernel/bmips_vec.S | 6 +++++- arch/mips/kernel/smp-bmips.c | 10 ++++++++-- 2 files changed, 13 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/mips/kernel/bmips_vec.S b/arch/mips/kernel/bmips_vec.S index f739aedcb50..bd79c4f9bff 100644 --- a/arch/mips/kernel/bmips_vec.S +++ b/arch/mips/kernel/bmips_vec.S @@ -54,7 +54,11 @@ LEAF(bmips_smp_movevec) /* set up CPU1 CBR; move BASE to 0xa000_0000 */ li k0, 0xff400000 mtc0 k0, $22, 6 - li k1, CKSEG1 | BMIPS_RELO_VECTOR_CONTROL_1 + /* set up relocation vector address based on thread ID */ + mfc0 k1, $22, 3 + srl k1, 16 + andi k1, 0x8000 + or k1, CKSEG1 | BMIPS_RELO_VECTOR_CONTROL_0 or k0, k1 li k1, 0xa0080000 sw k1, 0(k0) diff --git a/arch/mips/kernel/smp-bmips.c b/arch/mips/kernel/smp-bmips.c index 89417c9c6ac..159abc8842d 100644 --- a/arch/mips/kernel/smp-bmips.c +++ b/arch/mips/kernel/smp-bmips.c @@ -196,9 +196,15 @@ static void bmips_init_secondary(void) #if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) void __iomem *cbr = BMIPS_GET_CBR(); unsigned long old_vec; + unsigned long relo_vector; + int boot_cpu; - old_vec = __raw_readl(cbr + BMIPS_RELO_VECTOR_CONTROL_1); - __raw_writel(old_vec & ~0x20000000, cbr + BMIPS_RELO_VECTOR_CONTROL_1); + boot_cpu = !!(read_c0_brcm_cmt_local() & (1 << 31)); + relo_vector = boot_cpu ? BMIPS_RELO_VECTOR_CONTROL_0 : + BMIPS_RELO_VECTOR_CONTROL_1; + + old_vec = __raw_readl(cbr + relo_vector); + __raw_writel(old_vec & ~0x20000000, cbr + relo_vector); clear_c0_cause(smp_processor_id() ? C_SW1 : C_SW0); #elif defined(CONFIG_CPU_BMIPS5000) -- cgit v1.2.3-70-g09d2 From fa3e0cee12fbdd9e0b03470b2b8cf968f537c161 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sat, 27 Jul 2013 03:46:33 +0400 Subject: ARM: shmobile: BOCK-W: fix SDHI0 PFC settings The following message is printed on the BOCK-W kernel bootup: sh-pfc pfc-r8a7778: invalid group "sdhi0" for function "sdhi0" In addition, SD card cannot be detected. The reason is apparently that commit ca7bb309485e4ec89a9addd47bea (ARM: shmobile: bockw: add SDHI0 support) matched the previous version of commit 564617d2f92473031d035deb273da5 (sh-pfc: r8a7778: add SDHI support). Add the missing pin groups according to the BOCK-W board schematics. Signed-off-by: Sergei Shtylyov Acked-by: Kuninori Morimoto Signed-off-by: Simon Horman --- arch/arm/mach-shmobile/board-bockw.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-shmobile/board-bockw.c b/arch/arm/mach-shmobile/board-bockw.c index d5554646916..3354a85c90f 100644 --- a/arch/arm/mach-shmobile/board-bockw.c +++ b/arch/arm/mach-shmobile/board-bockw.c @@ -167,7 +167,13 @@ static const struct pinctrl_map bockw_pinctrl_map[] = { "usb1", "usb1"), /* SDHI0 */ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778", - "sdhi0", "sdhi0"), + "sdhi0_data4", "sdhi0"), + PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778", + "sdhi0_ctrl", "sdhi0"), + PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778", + "sdhi0_cd", "sdhi0"), + PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778", + "sdhi0_wp", "sdhi0"), }; #define FPGA 0x18200000 -- cgit v1.2.3-70-g09d2 From a601469386b543df2a4d97ad7d524716945278a3 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Fri, 26 Jul 2013 17:53:42 +0900 Subject: ARM: shmobile: lager: do not annotate gpio_buttons as __initdata When the gpio-keys device is registered using platform_device_register_data() the platform data argument, lager_keys_pdata is duplicated and thus should be marked as __initdata to avoid wasting memory. However, this is not true of gpio_buttons, a reference to it rather than its value is duplicated when lager_keys_pdata is duplicated. This avoids accessing freed memory if gpio-key events occur after unused kernel memory is freed late in the kernel's boot. This but was added when support for gpio-keys was added to lager in c3842e4fcbb7664276443b79187b7808c2e80a35 ("ARM: shmobile: lager: support GPIO switches") which was included in v3.11-rc1. Tested-by: Magnus Damm Signed-off-by: Simon Horman --- arch/arm/mach-shmobile/board-lager.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-shmobile/board-lager.c b/arch/arm/mach-shmobile/board-lager.c index d73e21d3ea8..8d6bd5c5efb 100644 --- a/arch/arm/mach-shmobile/board-lager.c +++ b/arch/arm/mach-shmobile/board-lager.c @@ -59,7 +59,7 @@ static __initdata struct gpio_led_platform_data lager_leds_pdata = { #define GPIO_KEY(c, g, d, ...) \ { .code = c, .gpio = g, .desc = d, .active_low = 1 } -static __initdata struct gpio_keys_button gpio_buttons[] = { +static struct gpio_keys_button gpio_buttons[] = { GPIO_KEY(KEY_4, RCAR_GP_PIN(1, 28), "SW2-pin4"), GPIO_KEY(KEY_3, RCAR_GP_PIN(1, 26), "SW2-pin3"), GPIO_KEY(KEY_2, RCAR_GP_PIN(1, 24), "SW2-pin2"), -- cgit v1.2.3-70-g09d2 From bed859c1eea89feaba2acbb57d967a6d6f68af09 Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Tue, 30 Jul 2013 11:33:00 +0100 Subject: ARM: 7800/1: ARMv7-M: Fix name of NVIC handler function MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The name changed in response to review comments for the nvic irqchip driver when the original name was already accepted into Russell King's tree. Signed-off-by: Uwe Kleine-König Signed-off-by: Russell King --- arch/arm/kernel/entry-v7m.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/kernel/entry-v7m.S b/arch/arm/kernel/entry-v7m.S index e00621f1403..52b26432c9a 100644 --- a/arch/arm/kernel/entry-v7m.S +++ b/arch/arm/kernel/entry-v7m.S @@ -49,7 +49,7 @@ __irq_entry: mov r1, sp stmdb sp!, {lr} @ routine called with r0 = irq number, r1 = struct pt_regs * - bl nvic_do_IRQ + bl nvic_handle_irq pop {lr} @ -- cgit v1.2.3-70-g09d2 From 067e710b9a982a92cc8294d7fa0f1e924c65bba1 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Tue, 30 Jul 2013 12:38:45 +0100 Subject: ARM: 7801/1: v6: prevent gcc 4.5 from reordering extended CP15 reads above is_smp() test Commit 621a0147d5c921f4cc33636ccd0602ad5d7cbfbc ("ARM: 7757/1: mm: don't flush icache in switch_mm with hardware broadcasting") breaks the boot on OMAP2430SDP with omap2plus_defconfig. Tracked to an undefined instruction abort from the CP15 read in cache_ops_need_broadcast(). It turns out that gcc 4.5 reorders the extended CP15 read above the is_smp() test. This breaks ARM1136 r0 cores, since they don't support several CP15 registers that later ARM cores do. ARM1136JF-S TRM section 3.2.1 "Register allocation" has the details. So mark the extended CP15 read as clobbering memory, which prevents the compiler from reordering it before the is_smp() test. Russell states that the code generated from this approach is preferable to marking the inline asm as volatile. Remove the existing condition code clobber as it's obsolete, per Nico's post: http://www.spinics.net/lists/arm-kernel/msg261208.html This patch is a collaboration with Will Deacon and Russell King. Comments from Paul Walmsley: Russell, if you accept this one, might you also add Will's ack from the lists: Comments from Paul Walmsley: I'd also be obliged if you could add a Cc: line for Jonathan Austin, since he helped test: Signed-off-by: Paul Walmsley Cc: Will Deacon Cc: Nicolas Pitre Cc: Tony Lindgren Acked-by: Will Deacon Cc: Jonathan Austin Signed-off-by: Russell King --- arch/arm/include/asm/cputype.h | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/include/asm/cputype.h b/arch/arm/include/asm/cputype.h index 8c25dc4e985..9672e978d50 100644 --- a/arch/arm/include/asm/cputype.h +++ b/arch/arm/include/asm/cputype.h @@ -89,13 +89,18 @@ extern unsigned int processor_id; __val; \ }) +/* + * The memory clobber prevents gcc 4.5 from reordering the mrc before + * any is_smp() tests, which can cause undefined instruction aborts on + * ARM1136 r0 due to the missing extended CP15 registers. + */ #define read_cpuid_ext(ext_reg) \ ({ \ unsigned int __val; \ asm("mrc p15, 0, %0, c0, " ext_reg \ : "=r" (__val) \ : \ - : "cc"); \ + : "memory"); \ __val; \ }) -- cgit v1.2.3-70-g09d2 From d982057f631df04f8d78321084a1a71ca51f3364 Mon Sep 17 00:00:00 2001 From: Torsten Kaiser Date: Tue, 23 Jul 2013 22:58:23 +0200 Subject: x86, amd, microcode: Fix error path in apply_microcode_amd() Return -1 (like Intels apply_microcode) when the loading fails, also do not set the active microcode level on failure. Signed-off-by: Torsten Kaiser Link: http://lkml.kernel.org/r/20130723225823.2e4e7588@googlemail.com Acked-by: Borislav Petkov Signed-off-by: H. Peter Anvin --- arch/x86/kernel/microcode_amd.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/microcode_amd.c b/arch/x86/kernel/microcode_amd.c index 47ebb1dbfbc..7a0adb7ee43 100644 --- a/arch/x86/kernel/microcode_amd.c +++ b/arch/x86/kernel/microcode_amd.c @@ -220,12 +220,13 @@ int apply_microcode_amd(int cpu) return 0; } - if (__apply_microcode_amd(mc_amd)) + if (__apply_microcode_amd(mc_amd)) { pr_err("CPU%d: update failed for patch_level=0x%08x\n", cpu, mc_amd->hdr.patch_id); - else - pr_info("CPU%d: new patch_level=0x%08x\n", cpu, - mc_amd->hdr.patch_id); + return -1; + } + pr_info("CPU%d: new patch_level=0x%08x\n", cpu, + mc_amd->hdr.patch_id); uci->cpu_sig.rev = mc_amd->hdr.patch_id; c->microcode = mc_amd->hdr.patch_id; -- cgit v1.2.3-70-g09d2 From f928d4f2a86f46b030fa0850385b4391fc2b5918 Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 4 Jul 2013 11:00:23 +0100 Subject: ARM: poison the vectors page Fill the empty regions of the vectors page with an exception generating instruction. This ensures that any inappropriate branch to the vector page is appropriately trapped, rather than just encountering some code to execute. (The vectors page was filled with zero before, which corresponds with the "andeq r0, r0, r0" instruction - a no-op.) Cc: Acked-by Nicolas Pitre Signed-off-by: Russell King --- arch/arm/kernel/traps.c | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'arch') diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index cab094c234e..9433e8a12b5 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -818,9 +818,19 @@ void __init early_trap_init(void *vectors_base) extern char __vectors_start[], __vectors_end[]; extern char __kuser_helper_start[], __kuser_helper_end[]; int kuser_sz = __kuser_helper_end - __kuser_helper_start; + unsigned i; vectors_page = vectors_base; + /* + * Poison the vectors page with an undefined instruction. This + * instruction is chosen to be undefined for both ARM and Thumb + * ISAs. The Thumb version is an undefined instruction with a + * branch back to the undefined instruction. + */ + for (i = 0; i < PAGE_SIZE / sizeof(u32); i++) + ((u32 *)vectors_base)[i] = 0xe7fddef1; + /* * Copy the vectors, stubs and kuser helpers (in entry-armv.S) * into the vector page, mapped at 0xffff0000, and ensure these -- cgit v1.2.3-70-g09d2 From 5b43e7a383d69381ffe53423e46dd0fafae07da3 Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 4 Jul 2013 11:32:04 +0100 Subject: ARM: poison memory between kuser helpers Poison the memory between each kuser helper. This ensures that any branch between the kuser helpers will be appropriately trapped. Cc: Acked-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/kernel/entry-armv.S | 25 ++++++++++++++++--------- 1 file changed, 16 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index a39cfc2a1f9..02437345289 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -742,6 +742,17 @@ ENDPROC(__switch_to) #endif .endm + .macro kuser_pad, sym, size + .if (. - \sym) & 3 + .rept 4 - (. - \sym) & 3 + .byte 0 + .endr + .endif + .rept (\size - (. - \sym)) / 4 + .word 0xe7fddef1 + .endr + .endm + .align 5 .globl __kuser_helper_start __kuser_helper_start: @@ -832,18 +843,13 @@ kuser_cmpxchg64_fixup: #error "incoherent kernel configuration" #endif - /* pad to next slot */ - .rept (16 - (. - __kuser_cmpxchg64)/4) - .word 0 - .endr - - .align 5 + kuser_pad __kuser_cmpxchg64, 64 __kuser_memory_barrier: @ 0xffff0fa0 smp_dmb arm usr_ret lr - .align 5 + kuser_pad __kuser_memory_barrier, 32 __kuser_cmpxchg: @ 0xffff0fc0 @@ -916,13 +922,14 @@ kuser_cmpxchg32_fixup: #endif - .align 5 + kuser_pad __kuser_cmpxchg, 32 __kuser_get_tls: @ 0xffff0fe0 ldr r0, [pc, #(16 - 8)] @ read TLS, set in kuser_get_tls_init usr_ret lr mrc p15, 0, r0, c13, c0, 3 @ 0xffff0fe8 hardware TLS code - .rep 4 + kuser_pad __kuser_get_tls, 16 + .rep 3 .word 0 @ 0xffff0ff0 software TLS value, then .endr @ pad up to __kuser_helper_version -- cgit v1.2.3-70-g09d2 From 19accfd373847ac3d10623c5d20f948846299741 Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 4 Jul 2013 11:40:32 +0100 Subject: ARM: move vector stubs Move the machine vector stubs into the page above the vector page, which we can prevent from being visible to userspace. Also move the reset stub, and place the swi vector at a location that the 'ldr' can get to it. This hides pointers into the kernel which could give valuable information to attackers, and reduces the number of exploitable instructions at a fixed address. Cc: Acked-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/Kconfig | 3 ++- arch/arm/kernel/entry-armv.S | 50 +++++++++++++++++++++----------------------- arch/arm/kernel/traps.c | 4 ++-- arch/arm/mm/mmu.c | 10 ++++++++- 4 files changed, 37 insertions(+), 30 deletions(-) (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index ba412e02ec0..123b7924904 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -218,7 +218,8 @@ config VECTORS_BASE default DRAM_BASE if REMAP_VECTORS_TO_RAM default 0x00000000 help - The base address of exception vectors. + The base address of exception vectors. This must be two pages + in size. config ARM_PATCH_PHYS_VIRT bool "Patch physical to virtual translations at runtime" if EMBEDDED diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index 02437345289..79a41fa978f 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -944,9 +944,9 @@ __kuser_helper_end: /* * Vector stubs. * - * This code is copied to 0xffff0200 so we can use branches in the - * vectors, rather than ldr's. Note that this code must not - * exceed 0x300 bytes. + * This code is copied to 0xffff1000 so we can use branches in the + * vectors, rather than ldr's. Note that this code must not exceed + * a page size. * * Common stub entry macro: * Enter in IRQ mode, spsr = SVC/USR CPSR, lr = SVC/USR PC @@ -995,6 +995,15 @@ ENDPROC(vector_\name) .globl __stubs_start __stubs_start: + @ This must be the first word + .word vector_swi + +vector_rst: + ARM( swi SYS_ERROR0 ) + THUMB( svc #0 ) + THUMB( nop ) + b vector_und + /* * Interrupt dispatcher */ @@ -1088,6 +1097,16 @@ __stubs_start: .align 5 +/*============================================================================= + * Address exception handler + *----------------------------------------------------------------------------- + * These aren't too critical. + * (they're not supposed to happen, and won't happen in 32-bit data mode). + */ + +vector_addrexcptn: + b vector_addrexcptn + /*============================================================================= * Undefined FIQs *----------------------------------------------------------------------------- @@ -1101,35 +1120,14 @@ __stubs_start: vector_fiq: subs pc, lr, #4 -/*============================================================================= - * Address exception handler - *----------------------------------------------------------------------------- - * These aren't too critical. - * (they're not supposed to happen, and won't happen in 32-bit data mode). - */ - -vector_addrexcptn: - b vector_addrexcptn - -/* - * We group all the following data together to optimise - * for CPUs with separate I & D caches. - */ - .align 5 - -.LCvswi: - .word vector_swi - .globl __stubs_end __stubs_end: - .equ stubs_offset, __vectors_start + 0x200 - __stubs_start + .equ stubs_offset, __vectors_start + 0x1000 - __stubs_start .globl __vectors_start __vectors_start: - ARM( swi SYS_ERROR0 ) - THUMB( svc #0 ) - THUMB( nop ) + W(b) vector_rst + stubs_offset W(b) vector_und + stubs_offset W(ldr) pc, .LCvswi + stubs_offset W(b) vector_pabt + stubs_offset diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 9433e8a12b5..2c8c7fa78b8 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -837,7 +837,7 @@ void __init early_trap_init(void *vectors_base) * are visible to the instruction stream. */ memcpy((void *)vectors, __vectors_start, __vectors_end - __vectors_start); - memcpy((void *)vectors + 0x200, __stubs_start, __stubs_end - __stubs_start); + memcpy((void *)vectors + 0x1000, __stubs_start, __stubs_end - __stubs_start); memcpy((void *)vectors + 0x1000 - kuser_sz, __kuser_helper_start, kuser_sz); /* @@ -852,7 +852,7 @@ void __init early_trap_init(void *vectors_base) memcpy((void *)(vectors + KERN_SIGRETURN_CODE - CONFIG_VECTORS_BASE), sigreturn_codes, sizeof(sigreturn_codes)); - flush_icache_range(vectors, vectors + PAGE_SIZE); + flush_icache_range(vectors, vectors + PAGE_SIZE * 2); modify_domain(DOMAIN_USER, DOMAIN_CLIENT); #else /* ifndef CONFIG_CPU_V7M */ /* diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 4f56617a239..9ea274d1af6 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -1160,7 +1160,7 @@ static void __init devicemaps_init(struct machine_desc *mdesc) /* * Allocate the vector page early. */ - vectors = early_alloc(PAGE_SIZE); + vectors = early_alloc(PAGE_SIZE * 2); early_trap_init(vectors); @@ -1210,10 +1210,18 @@ static void __init devicemaps_init(struct machine_desc *mdesc) if (!vectors_high()) { map.virtual = 0; + map.length = PAGE_SIZE * 2; map.type = MT_LOW_VECTORS; create_mapping(&map); } + /* Now create a kernel read-only mapping */ + map.pfn += 1; + map.virtual = 0xffff0000 + PAGE_SIZE; + map.length = PAGE_SIZE; + map.type = MT_LOW_VECTORS; + create_mapping(&map); + /* * Ask the machine support to map in the statically mapped devices. */ -- cgit v1.2.3-70-g09d2 From b9b32bf70f2fb710b07c94e13afbc729afe221da Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 4 Jul 2013 12:03:31 +0100 Subject: ARM: use linker magic for vectors and vector stubs Use linker magic to create the vectors and vector stubs: we can tell the linker to place them at an appropriate VMA, but keep the LMA within the kernel. This gets rid of some unnecessary symbol manipulation, and have the linker calculate the relocations appropriately. Cc: Acked-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/kernel/entry-armv.S | 28 ++++++++++------------------ arch/arm/kernel/vmlinux.lds.S | 17 +++++++++++++++++ 2 files changed, 27 insertions(+), 18 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index 79a41fa978f..7e1ae91e5b1 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -993,7 +993,7 @@ ENDPROC(vector_\name) 1: .endm - .globl __stubs_start + .section .stubs, "ax", %progbits __stubs_start: @ This must be the first word .word vector_swi @@ -1120,24 +1120,16 @@ vector_addrexcptn: vector_fiq: subs pc, lr, #4 - .globl __stubs_end -__stubs_end: - - .equ stubs_offset, __vectors_start + 0x1000 - __stubs_start - - .globl __vectors_start + .section .vectors, "ax", %progbits __vectors_start: - W(b) vector_rst + stubs_offset - W(b) vector_und + stubs_offset - W(ldr) pc, .LCvswi + stubs_offset - W(b) vector_pabt + stubs_offset - W(b) vector_dabt + stubs_offset - W(b) vector_addrexcptn + stubs_offset - W(b) vector_irq + stubs_offset - W(b) vector_fiq + stubs_offset - - .globl __vectors_end -__vectors_end: + W(b) vector_rst + W(b) vector_und + W(ldr) pc, __vectors_start + 0x1000 + W(b) vector_pabt + W(b) vector_dabt + W(b) vector_addrexcptn + W(b) vector_irq + W(b) vector_fiq .data diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S index fa25e4e425f..7bcee5c9b60 100644 --- a/arch/arm/kernel/vmlinux.lds.S +++ b/arch/arm/kernel/vmlinux.lds.S @@ -148,6 +148,23 @@ SECTIONS . = ALIGN(PAGE_SIZE); __init_begin = .; #endif + /* + * The vectors and stubs are relocatable code, and the + * only thing that matters is their relative offsets + */ + __vectors_start = .; + .vectors 0 : AT(__vectors_start) { + *(.vectors) + } + . = __vectors_start + SIZEOF(.vectors); + __vectors_end = .; + + __stubs_start = .; + .stubs 0x1000 : AT(__stubs_start) { + *(.stubs) + } + . = __stubs_start + SIZEOF(.stubs); + __stubs_end = .; INIT_TEXT_SECTION(8) .exit.text : { -- cgit v1.2.3-70-g09d2 From e39e3f3ebfef03450cf7bfa7a974a8c61f7980c8 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 9 Jul 2013 01:03:17 +0100 Subject: ARM: update FIQ support for relocation of vectors FIQ should no longer copy the FIQ code into the user visible vector page. Instead, it should use the hidden page. This change makes that happen. Cc: Acked-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/kernel/entry-armv.S | 3 +++ arch/arm/kernel/fiq.c | 19 ++++++++++++++----- 2 files changed, 17 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index 7e1ae91e5b1..94caefb550b 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -1120,6 +1120,9 @@ vector_addrexcptn: vector_fiq: subs pc, lr, #4 + .globl vector_fiq_offset + .equ vector_fiq_offset, vector_fiq + .section .vectors, "ax", %progbits __vectors_start: W(b) vector_rst diff --git a/arch/arm/kernel/fiq.c b/arch/arm/kernel/fiq.c index 2adda11f712..25442f45114 100644 --- a/arch/arm/kernel/fiq.c +++ b/arch/arm/kernel/fiq.c @@ -47,6 +47,11 @@ #include #include +#define FIQ_OFFSET ({ \ + extern void *vector_fiq_offset; \ + (unsigned)&vector_fiq_offset; \ + }) + static unsigned long no_fiq_insn; /* Default reacquire function @@ -80,13 +85,16 @@ int show_fiq_list(struct seq_file *p, int prec) void set_fiq_handler(void *start, unsigned int length) { #if defined(CONFIG_CPU_USE_DOMAINS) - memcpy((void *)0xffff001c, start, length); + void *base = (void *)0xffff0000; #else - memcpy(vectors_page + 0x1c, start, length); + void *base = vectors_page; #endif - flush_icache_range(0xffff001c, 0xffff001c + length); + unsigned offset = FIQ_OFFSET; + + memcpy(base + offset, start, length); + flush_icache_range(0xffff0000 + offset, 0xffff0000 + offset + length); if (!vectors_high()) - flush_icache_range(0x1c, 0x1c + length); + flush_icache_range(offset, offset + length); } int claim_fiq(struct fiq_handler *f) @@ -144,6 +152,7 @@ EXPORT_SYMBOL(disable_fiq); void __init init_FIQ(int start) { - no_fiq_insn = *(unsigned long *)0xffff001c; + unsigned offset = FIQ_OFFSET; + no_fiq_insn = *(unsigned long *)(0xffff0000 + offset); fiq_start = start; } -- cgit v1.2.3-70-g09d2 From f6f91b0d9fd971c630cef908dde8fe8795aefbf8 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 23 Jul 2013 18:37:00 +0100 Subject: ARM: allow kuser helpers to be removed from the vector page Provide a kernel configuration option to allow the kernel user helpers to be removed from the vector page, thereby preventing their use with ROP (return orientated programming) attacks. This option is only visible for CPU architectures which natively support all the operations which kernel user helpers would normally provide, and must be enabled with caution. Cc: Acked-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/kernel/entry-armv.S | 3 +++ arch/arm/kernel/traps.c | 23 ++++++++++++++--------- arch/arm/mm/Kconfig | 34 ++++++++++++++++++++++++++++++++++ 3 files changed, 51 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index 94caefb550b..d40d0ef389d 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -753,6 +753,7 @@ ENDPROC(__switch_to) .endr .endm +#ifdef CONFIG_KUSER_HELPERS .align 5 .globl __kuser_helper_start __kuser_helper_start: @@ -939,6 +940,8 @@ __kuser_helper_version: @ 0xffff0ffc .globl __kuser_helper_end __kuser_helper_end: +#endif + THUMB( .thumb ) /* diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 2c8c7fa78b8..e3ca35ccd38 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -800,15 +800,26 @@ void __init trap_init(void) return; } -static void __init kuser_get_tls_init(unsigned long vectors) +#ifdef CONFIG_KUSER_HELPERS +static void __init kuser_init(void *vectors) { + extern char __kuser_helper_start[], __kuser_helper_end[]; + int kuser_sz = __kuser_helper_end - __kuser_helper_start; + + memcpy(vectors + 0x1000 - kuser_sz, __kuser_helper_start, kuser_sz); + /* * vectors + 0xfe0 = __kuser_get_tls * vectors + 0xfe8 = hardware TLS instruction at 0xffff0fe8 */ if (tls_emu || has_tls_reg) - memcpy((void *)vectors + 0xfe0, (void *)vectors + 0xfe8, 4); + memcpy(vectors + 0xfe0, vectors + 0xfe8, 4); +} +#else +static void __init kuser_init(void *vectors) +{ } +#endif void __init early_trap_init(void *vectors_base) { @@ -816,8 +827,6 @@ void __init early_trap_init(void *vectors_base) unsigned long vectors = (unsigned long)vectors_base; extern char __stubs_start[], __stubs_end[]; extern char __vectors_start[], __vectors_end[]; - extern char __kuser_helper_start[], __kuser_helper_end[]; - int kuser_sz = __kuser_helper_end - __kuser_helper_start; unsigned i; vectors_page = vectors_base; @@ -838,12 +847,8 @@ void __init early_trap_init(void *vectors_base) */ memcpy((void *)vectors, __vectors_start, __vectors_end - __vectors_start); memcpy((void *)vectors + 0x1000, __stubs_start, __stubs_end - __stubs_start); - memcpy((void *)vectors + 0x1000 - kuser_sz, __kuser_helper_start, kuser_sz); - /* - * Do processor specific fixups for the kuser helpers - */ - kuser_get_tls_init(vectors); + kuser_init(vectors_base); /* * Copy signal return handlers into the vector page, and diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 6cacdc8dd65..db5c2cab8fd 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -421,24 +421,28 @@ config CPU_32v3 select CPU_USE_DOMAINS if MMU select NEEDS_SYSCALL_FOR_CMPXCHG if SMP select TLS_REG_EMUL if SMP || !MMU + select NEED_KUSER_HELPERS config CPU_32v4 bool select CPU_USE_DOMAINS if MMU select NEEDS_SYSCALL_FOR_CMPXCHG if SMP select TLS_REG_EMUL if SMP || !MMU + select NEED_KUSER_HELPERS config CPU_32v4T bool select CPU_USE_DOMAINS if MMU select NEEDS_SYSCALL_FOR_CMPXCHG if SMP select TLS_REG_EMUL if SMP || !MMU + select NEED_KUSER_HELPERS config CPU_32v5 bool select CPU_USE_DOMAINS if MMU select NEEDS_SYSCALL_FOR_CMPXCHG if SMP select TLS_REG_EMUL if SMP || !MMU + select NEED_KUSER_HELPERS config CPU_32v6 bool @@ -776,6 +780,7 @@ config CPU_BPREDICT_DISABLE config TLS_REG_EMUL bool + select NEED_KUSER_HELPERS help An SMP system using a pre-ARMv6 processor (there are apparently a few prototypes like that in existence) and therefore access to @@ -783,11 +788,40 @@ config TLS_REG_EMUL config NEEDS_SYSCALL_FOR_CMPXCHG bool + select NEED_KUSER_HELPERS help SMP on a pre-ARMv6 processor? Well OK then. Forget about fast user space cmpxchg support. It is just not possible. +config NEED_KUSER_HELPERS + bool + +config KUSER_HELPERS + bool "Enable kuser helpers in vector page" if !NEED_KUSER_HELPERS + default y + help + Warning: disabling this option may break user programs. + + Provide kuser helpers in the vector page. The kernel provides + helper code to userspace in read only form at a fixed location + in the high vector page to allow userspace to be independent of + the CPU type fitted to the system. This permits binaries to be + run on ARMv4 through to ARMv7 without modification. + + However, the fixed address nature of these helpers can be used + by ROP (return orientated programming) authors when creating + exploits. + + If all of the binaries and libraries which run on your platform + are built specifically for your platform, and make no use of + these helpers, then you can turn this option off. However, + when such an binary or library is run, it will receive a SIGILL + signal, which will terminate the program. + + Say N here only if you are absolutely certain that you do not + need these helpers; otherwise, the safe option is to say Y. + config DMA_CACHE_RWFO bool "Enable read/write for ownership DMA cache maintenance" depends on CPU_V6K && SMP -- cgit v1.2.3-70-g09d2 From 31a1b26f16e822577def5402ffc79cfe4aed2db9 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Wed, 31 Jul 2013 13:53:36 -0700 Subject: arch/x86/platform/ce4100/ce4100.c: include reboot.h Fix the build: arch/x86/platform/ce4100/ce4100.c: In function 'x86_ce4100_early_setup': arch/x86/platform/ce4100/ce4100.c:165:2: error: 'reboot_type' undeclared (first use in this function) Reported-by: Wu Fengguang Cc: Thomas Gleixner Cc: Ingo Molnar Cc: "H. Peter Anvin" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/x86/platform/ce4100/ce4100.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/x86/platform/ce4100/ce4100.c b/arch/x86/platform/ce4100/ce4100.c index 643b8b5eee8..8244f5ec2f4 100644 --- a/arch/x86/platform/ce4100/ce4100.c +++ b/arch/x86/platform/ce4100/ce4100.c @@ -12,6 +12,7 @@ #include #include #include +#include #include #include #include -- cgit v1.2.3-70-g09d2 From 50861f5a02dbf939c27d35a26c472885e2844188 Mon Sep 17 00:00:00 2001 From: John David Anglin Date: Tue, 23 Jul 2013 12:27:52 -0400 Subject: parisc: Fix cache routines to ignore vma's with an invalid pfn The parisc architecture does not have a pte special bit. As a result, special mappings are handled with the VM_PFNMAP and VM_MIXEDMAP flags. VM_MIXEDMAP mappings may or may not have a "struct page" backing. When pfn_valid() is false, there is no "struct page" backing. Otherwise, they are treated as normal pages. The FireGL driver uses the VM_MIXEDMAP without a backing "struct page". This treatment caused a panic due to a TLB data miss in update_mmu_cache. This appeared to be in the code generated for page_address(). We were in fact using a very circular bit of code to determine the physical address of the PFN in various cache routines. This wasn't valid when there was no "struct page" backing. The needed address can in fact be determined simply from the PFN itself without using the "struct page". The attached patch updates update_mmu_cache(), flush_cache_mm(), flush_cache_range() and flush_cache_page() to check pfn_valid() and to directly compute the PFN physical and virtual addresses. Signed-off-by: John David Anglin Cc: # 3.10 Signed-off-by: Helge Deller --- arch/parisc/kernel/cache.c | 135 ++++++++++++++++++++++++--------------------- 1 file changed, 71 insertions(+), 64 deletions(-) (limited to 'arch') diff --git a/arch/parisc/kernel/cache.c b/arch/parisc/kernel/cache.c index 2e65aa54bd1..c035673209f 100644 --- a/arch/parisc/kernel/cache.c +++ b/arch/parisc/kernel/cache.c @@ -71,18 +71,27 @@ flush_cache_all_local(void) } EXPORT_SYMBOL(flush_cache_all_local); +/* Virtual address of pfn. */ +#define pfn_va(pfn) __va(PFN_PHYS(pfn)) + void update_mmu_cache(struct vm_area_struct *vma, unsigned long address, pte_t *ptep) { - struct page *page = pte_page(*ptep); + unsigned long pfn = pte_pfn(*ptep); + struct page *page; - if (pfn_valid(page_to_pfn(page)) && page_mapping(page) && - test_bit(PG_dcache_dirty, &page->flags)) { + /* We don't have pte special. As a result, we can be called with + an invalid pfn and we don't need to flush the kernel dcache page. + This occurs with FireGL card in C8000. */ + if (!pfn_valid(pfn)) + return; - flush_kernel_dcache_page(page); + page = pfn_to_page(pfn); + if (page_mapping(page) && test_bit(PG_dcache_dirty, &page->flags)) { + flush_kernel_dcache_page_addr(pfn_va(pfn)); clear_bit(PG_dcache_dirty, &page->flags); } else if (parisc_requires_coherency()) - flush_kernel_dcache_page(page); + flush_kernel_dcache_page_addr(pfn_va(pfn)); } void @@ -495,44 +504,42 @@ static inline pte_t *get_ptep(pgd_t *pgd, unsigned long addr) void flush_cache_mm(struct mm_struct *mm) { + struct vm_area_struct *vma; + pgd_t *pgd; + /* Flushing the whole cache on each cpu takes forever on rp3440, etc. So, avoid it if the mm isn't too big. */ - if (mm_total_size(mm) < parisc_cache_flush_threshold) { - struct vm_area_struct *vma; - - if (mm->context == mfsp(3)) { - for (vma = mm->mmap; vma; vma = vma->vm_next) { - flush_user_dcache_range_asm(vma->vm_start, - vma->vm_end); - if (vma->vm_flags & VM_EXEC) - flush_user_icache_range_asm( - vma->vm_start, vma->vm_end); - } - } else { - pgd_t *pgd = mm->pgd; - - for (vma = mm->mmap; vma; vma = vma->vm_next) { - unsigned long addr; - - for (addr = vma->vm_start; addr < vma->vm_end; - addr += PAGE_SIZE) { - pte_t *ptep = get_ptep(pgd, addr); - if (ptep != NULL) { - pte_t pte = *ptep; - __flush_cache_page(vma, addr, - page_to_phys(pte_page(pte))); - } - } - } + if (mm_total_size(mm) >= parisc_cache_flush_threshold) { + flush_cache_all(); + return; + } + + if (mm->context == mfsp(3)) { + for (vma = mm->mmap; vma; vma = vma->vm_next) { + flush_user_dcache_range_asm(vma->vm_start, vma->vm_end); + if ((vma->vm_flags & VM_EXEC) == 0) + continue; + flush_user_icache_range_asm(vma->vm_start, vma->vm_end); } return; } -#ifdef CONFIG_SMP - flush_cache_all(); -#else - flush_cache_all_local(); -#endif + pgd = mm->pgd; + for (vma = mm->mmap; vma; vma = vma->vm_next) { + unsigned long addr; + + for (addr = vma->vm_start; addr < vma->vm_end; + addr += PAGE_SIZE) { + unsigned long pfn; + pte_t *ptep = get_ptep(pgd, addr); + if (!ptep) + continue; + pfn = pte_pfn(*ptep); + if (!pfn_valid(pfn)) + continue; + __flush_cache_page(vma, addr, PFN_PHYS(pfn)); + } + } } void @@ -556,33 +563,32 @@ flush_user_icache_range(unsigned long start, unsigned long end) void flush_cache_range(struct vm_area_struct *vma, unsigned long start, unsigned long end) { + unsigned long addr; + pgd_t *pgd; + BUG_ON(!vma->vm_mm->context); - if ((end - start) < parisc_cache_flush_threshold) { - if (vma->vm_mm->context == mfsp(3)) { - flush_user_dcache_range_asm(start, end); - if (vma->vm_flags & VM_EXEC) - flush_user_icache_range_asm(start, end); - } else { - unsigned long addr; - pgd_t *pgd = vma->vm_mm->pgd; - - for (addr = start & PAGE_MASK; addr < end; - addr += PAGE_SIZE) { - pte_t *ptep = get_ptep(pgd, addr); - if (ptep != NULL) { - pte_t pte = *ptep; - flush_cache_page(vma, - addr, pte_pfn(pte)); - } - } - } - } else { -#ifdef CONFIG_SMP + if ((end - start) >= parisc_cache_flush_threshold) { flush_cache_all(); -#else - flush_cache_all_local(); -#endif + return; + } + + if (vma->vm_mm->context == mfsp(3)) { + flush_user_dcache_range_asm(start, end); + if (vma->vm_flags & VM_EXEC) + flush_user_icache_range_asm(start, end); + return; + } + + pgd = vma->vm_mm->pgd; + for (addr = start & PAGE_MASK; addr < end; addr += PAGE_SIZE) { + unsigned long pfn; + pte_t *ptep = get_ptep(pgd, addr); + if (!ptep) + continue; + pfn = pte_pfn(*ptep); + if (pfn_valid(pfn)) + __flush_cache_page(vma, addr, PFN_PHYS(pfn)); } } @@ -591,9 +597,10 @@ flush_cache_page(struct vm_area_struct *vma, unsigned long vmaddr, unsigned long { BUG_ON(!vma->vm_mm->context); - flush_tlb_page(vma, vmaddr); - __flush_cache_page(vma, vmaddr, page_to_phys(pfn_to_page(pfn))); - + if (pfn_valid(pfn)) { + flush_tlb_page(vma, vmaddr); + __flush_cache_page(vma, vmaddr, PFN_PHYS(pfn)); + } } #ifdef CONFIG_PARISC_TMPALIAS -- cgit v1.2.3-70-g09d2 From 78f1386cb0777e7413df734ddc30e41d0a6522a9 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Wed, 10 Jul 2013 23:50:35 +0200 Subject: parisc: add defconfig for c8000 machine Signed-off-by: Helge Deller --- arch/parisc/configs/c8000_defconfig | 279 ++++++++++++++++++++++++++++++++++++ 1 file changed, 279 insertions(+) create mode 100644 arch/parisc/configs/c8000_defconfig (limited to 'arch') diff --git a/arch/parisc/configs/c8000_defconfig b/arch/parisc/configs/c8000_defconfig new file mode 100644 index 00000000000..f1100636129 --- /dev/null +++ b/arch/parisc/configs/c8000_defconfig @@ -0,0 +1,279 @@ +# CONFIG_LOCALVERSION_AUTO is not set +CONFIG_SYSVIPC=y +CONFIG_POSIX_MQUEUE=y +CONFIG_FHANDLE=y +CONFIG_BSD_PROCESS_ACCT=y +CONFIG_BSD_PROCESS_ACCT_V3=y +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_RELAY=y +CONFIG_BLK_DEV_INITRD=y +CONFIG_RD_BZIP2=y +CONFIG_RD_LZMA=y +CONFIG_RD_LZO=y +CONFIG_EXPERT=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_SLAB=y +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MODVERSIONS=y +CONFIG_BLK_DEV_INTEGRITY=y +CONFIG_PA8X00=y +CONFIG_MLONGCALLS=y +CONFIG_64BIT=y +CONFIG_SMP=y +CONFIG_PREEMPT=y +# CONFIG_CROSS_MEMORY_ATTACH is not set +CONFIG_IOMMU_CCIO=y +CONFIG_PCI=y +CONFIG_PCI_LBA=y +# CONFIG_SUPERIO is not set +# CONFIG_CHASSIS_LCD_LED is not set +# CONFIG_PDC_CHASSIS is not set +# CONFIG_PDC_CHASSIS_WARN is not set +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_BINFMT_MISC=m +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_XFRM_USER=m +CONFIG_XFRM_SUB_POLICY=y +CONFIG_NET_KEY=m +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +CONFIG_NET_IPIP=m +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +CONFIG_SYN_COOKIES=y +CONFIG_INET_AH=m +CONFIG_INET_ESP=m +CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_MODE_BEET=m +CONFIG_INET_DIAG=m +# CONFIG_IPV6 is not set +CONFIG_IP_DCCP=m +# CONFIG_IP_DCCP_CCID3 is not set +CONFIG_TIPC=m +CONFIG_LLC2=m +CONFIG_DNS_RESOLVER=y +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_STANDALONE is not set +CONFIG_PARPORT=y +CONFIG_PARPORT_PC=y +CONFIG_PARPORT_PC_FIFO=y +CONFIG_BLK_DEV_UMEM=m +CONFIG_BLK_DEV_LOOP=m +CONFIG_BLK_DEV_CRYPTOLOOP=m +CONFIG_BLK_DEV_SX8=m +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_SIZE=6144 +CONFIG_CDROM_PKTCDVD=m +CONFIG_CDROM_PKTCDVD_WCACHE=y +CONFIG_ATA_OVER_ETH=m +CONFIG_IDE=y +CONFIG_BLK_DEV_IDECD=y +CONFIG_BLK_DEV_PLATFORM=y +CONFIG_BLK_DEV_GENERIC=y +CONFIG_BLK_DEV_SIIMAGE=y +CONFIG_SCSI=y +CONFIG_BLK_DEV_SD=y +CONFIG_CHR_DEV_ST=m +CONFIG_BLK_DEV_SR=m +CONFIG_CHR_DEV_SG=y +CONFIG_CHR_DEV_SCH=m +CONFIG_SCSI_CONSTANTS=y +CONFIG_SCSI_LOGGING=y +CONFIG_SCSI_FC_ATTRS=y +CONFIG_SCSI_SAS_LIBSAS=m +CONFIG_ISCSI_TCP=m +CONFIG_ISCSI_BOOT_SYSFS=m +CONFIG_FUSION=y +CONFIG_FUSION_SPI=y +CONFIG_FUSION_SAS=y +CONFIG_NETDEVICES=y +CONFIG_DUMMY=m +CONFIG_NETCONSOLE=m +CONFIG_TUN=y +CONFIG_E1000=y +CONFIG_PPP=m +CONFIG_PPP_BSDCOMP=m +CONFIG_PPP_DEFLATE=m +CONFIG_PPP_MPPE=m +CONFIG_PPPOE=m +CONFIG_PPP_ASYNC=m +CONFIG_PPP_SYNC_TTY=m +# CONFIG_WLAN is not set +CONFIG_INPUT_FF_MEMLESS=m +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_KEYBOARD_HIL_OLD is not set +# CONFIG_KEYBOARD_HIL is not set +CONFIG_MOUSE_PS2=m +CONFIG_INPUT_MISC=y +CONFIG_INPUT_CM109=m +CONFIG_SERIO_SERPORT=m +CONFIG_SERIO_PARKBD=m +CONFIG_SERIO_GSCPS2=m +# CONFIG_HP_SDC is not set +CONFIG_SERIO_PCIPS2=m +CONFIG_SERIO_LIBPS2=y +CONFIG_SERIO_RAW=m +CONFIG_SERIAL_8250=y +# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=8 +CONFIG_SERIAL_8250_RUNTIME_UARTS=8 +CONFIG_SERIAL_8250_EXTENDED=y +# CONFIG_SERIAL_MUX is not set +CONFIG_SERIAL_JSM=m +CONFIG_PRINTER=y +CONFIG_HW_RANDOM=y +CONFIG_RAW_DRIVER=m +CONFIG_PTP_1588_CLOCK=y +CONFIG_SSB=m +CONFIG_SSB_DRIVER_PCICORE=y +CONFIG_AGP=y +CONFIG_AGP_PARISC=y +CONFIG_DRM=y +CONFIG_DRM_RADEON=y +CONFIG_FIRMWARE_EDID=y +CONFIG_FB_FOREIGN_ENDIAN=y +CONFIG_FB_MODE_HELPERS=y +CONFIG_FB_TILEBLITTING=y +# CONFIG_FB_STI is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +# CONFIG_LCD_CLASS_DEVICE is not set +# CONFIG_BACKLIGHT_GENERIC is not set +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_STI_CONSOLE is not set +CONFIG_LOGO=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +# CONFIG_LOGO_LINUX_CLUT224 is not set +CONFIG_SOUND=m +CONFIG_SND=m +CONFIG_SND_SEQUENCER=m +CONFIG_SND_SEQ_DUMMY=m +CONFIG_SND_MIXER_OSS=m +CONFIG_SND_PCM_OSS=m +CONFIG_SND_SEQUENCER_OSS=y +CONFIG_SND_VERBOSE_PRINTK=y +CONFIG_SND_AD1889=m +# CONFIG_SND_USB is not set +# CONFIG_SND_GSC is not set +CONFIG_HID_A4TECH=m +CONFIG_HID_APPLE=m +CONFIG_HID_BELKIN=m +CONFIG_HID_CHERRY=m +CONFIG_HID_CHICONY=m +CONFIG_HID_CYPRESS=m +CONFIG_HID_DRAGONRISE=m +CONFIG_HID_EZKEY=m +CONFIG_HID_KYE=m +CONFIG_HID_GYRATION=m +CONFIG_HID_TWINHAN=m +CONFIG_HID_KENSINGTON=m +CONFIG_HID_LOGITECH=m +CONFIG_HID_LOGITECH_DJ=m +CONFIG_HID_MICROSOFT=m +CONFIG_HID_MONTEREY=m +CONFIG_HID_NTRIG=m +CONFIG_HID_ORTEK=m +CONFIG_HID_PANTHERLORD=m +CONFIG_HID_PETALYNX=m +CONFIG_HID_SAMSUNG=m +CONFIG_HID_SUNPLUS=m +CONFIG_HID_GREENASIA=m +CONFIG_HID_SMARTJOYPLUS=m +CONFIG_HID_TOPSEED=m +CONFIG_HID_THRUSTMASTER=m +CONFIG_HID_ZEROPLUS=m +CONFIG_USB_HID=m +CONFIG_USB=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_STORAGE=y +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +CONFIG_EXT2_FS_POSIX_ACL=y +CONFIG_EXT2_FS_SECURITY=y +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +CONFIG_EXT4_FS=m +CONFIG_REISERFS_FS=m +CONFIG_REISERFS_PROC_INFO=y +CONFIG_XFS_FS=m +CONFIG_XFS_POSIX_ACL=y +CONFIG_QUOTA=y +CONFIG_QFMT_V1=m +CONFIG_QFMT_V2=m +CONFIG_AUTOFS4_FS=m +CONFIG_FUSE_FS=m +CONFIG_ISO9660_FS=y +CONFIG_JOLIET=y +CONFIG_MSDOS_FS=m +CONFIG_VFAT_FS=m +CONFIG_PROC_KCORE=y +CONFIG_TMPFS=y +CONFIG_TMPFS_XATTR=y +CONFIG_NFS_FS=m +CONFIG_NLS_CODEPAGE_437=m +CONFIG_NLS_CODEPAGE_737=m +CONFIG_NLS_CODEPAGE_775=m +CONFIG_NLS_CODEPAGE_850=m +CONFIG_NLS_CODEPAGE_852=m +CONFIG_NLS_CODEPAGE_855=m +CONFIG_NLS_CODEPAGE_857=m +CONFIG_NLS_CODEPAGE_860=m +CONFIG_NLS_CODEPAGE_861=m +CONFIG_NLS_CODEPAGE_862=m +CONFIG_NLS_CODEPAGE_863=m +CONFIG_NLS_CODEPAGE_864=m +CONFIG_NLS_CODEPAGE_865=m +CONFIG_NLS_CODEPAGE_866=m +CONFIG_NLS_CODEPAGE_869=m +CONFIG_NLS_CODEPAGE_936=m +CONFIG_NLS_CODEPAGE_950=m +CONFIG_NLS_CODEPAGE_932=m +CONFIG_NLS_CODEPAGE_949=m +CONFIG_NLS_CODEPAGE_874=m +CONFIG_NLS_ISO8859_8=m +CONFIG_NLS_CODEPAGE_1250=m +CONFIG_NLS_CODEPAGE_1251=m +CONFIG_NLS_ASCII=m +CONFIG_NLS_ISO8859_1=m +CONFIG_NLS_ISO8859_2=m +CONFIG_NLS_ISO8859_3=m +CONFIG_NLS_ISO8859_4=m +CONFIG_NLS_ISO8859_5=m +CONFIG_NLS_ISO8859_6=m +CONFIG_NLS_ISO8859_7=m +CONFIG_NLS_ISO8859_9=m +CONFIG_NLS_ISO8859_13=m +CONFIG_NLS_ISO8859_14=m +CONFIG_NLS_ISO8859_15=m +CONFIG_NLS_KOI8_R=m +CONFIG_NLS_KOI8_U=m +CONFIG_NLS_UTF8=m +CONFIG_UNUSED_SYMBOLS=y +CONFIG_DEBUG_FS=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_SLAB=y +CONFIG_DEBUG_SLAB_LEAK=y +CONFIG_DEBUG_MEMORY_INIT=y +CONFIG_DEBUG_STACKOVERFLOW=y +CONFIG_LOCKUP_DETECTOR=y +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y +CONFIG_PANIC_ON_OOPS=y +CONFIG_DEBUG_RT_MUTEXES=y +CONFIG_RT_MUTEX_TESTER=y +CONFIG_PROVE_RCU_DELAY=y +CONFIG_DEBUG_BLOCK_EXT_DEVT=y +CONFIG_LATENCYTOP=y +CONFIG_DEBUG_STRICT_USER_COPY_CHECKS=y +CONFIG_KEYS=y +# CONFIG_CRYPTO_HW is not set +CONFIG_FONTS=y -- cgit v1.2.3-70-g09d2 From 5a0ce2dc218ea9a6e659dcc5a4827975cb13104f Mon Sep 17 00:00:00 2001 From: John David Anglin Date: Sun, 28 Jul 2013 17:49:53 -0400 Subject: parisc: Remove arch/parisc/kernel/sys32.h header The KERNEL_SYSCALL define is not used anymore so the header can be removed. Signed-off-by: John David Anglin Signed-off-by: Helge Deller --- arch/parisc/kernel/signal.c | 7 ------- arch/parisc/kernel/signal32.c | 1 - arch/parisc/kernel/sys32.h | 36 ------------------------------------ arch/parisc/kernel/sys_parisc32.c | 2 -- 4 files changed, 46 deletions(-) delete mode 100644 arch/parisc/kernel/sys32.h (limited to 'arch') diff --git a/arch/parisc/kernel/signal.c b/arch/parisc/kernel/signal.c index 940188d1942..07349b00268 100644 --- a/arch/parisc/kernel/signal.c +++ b/arch/parisc/kernel/signal.c @@ -55,13 +55,6 @@ * this. */ #define A(__x) ((unsigned long)(__x)) -/* - * Atomically swap in the new signal mask, and wait for a signal. - */ -#ifdef CONFIG_64BIT -#include "sys32.h" -#endif - /* * Do a signal return - restore sigcontext. */ diff --git a/arch/parisc/kernel/signal32.c b/arch/parisc/kernel/signal32.c index 33eca1b0492..6c6a271a614 100644 --- a/arch/parisc/kernel/signal32.c +++ b/arch/parisc/kernel/signal32.c @@ -34,7 +34,6 @@ #include #include "signal32.h" -#include "sys32.h" #define DEBUG_COMPAT_SIG 0 #define DEBUG_COMPAT_SIG_LEVEL 2 diff --git a/arch/parisc/kernel/sys32.h b/arch/parisc/kernel/sys32.h deleted file mode 100644 index 60dd470f39f..00000000000 --- a/arch/parisc/kernel/sys32.h +++ /dev/null @@ -1,36 +0,0 @@ -/* - * Copyright (C) 2002 Richard Hirst - * Copyright (C) 2003 James Bottomley - * Copyright (C) 2003 Randolph Chung - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#ifndef _PARISC64_KERNEL_SYS32_H -#define _PARISC64_KERNEL_SYS32_H - -#include - -/* Call a kernel syscall which will use kernel space instead of user - * space for its copy_to/from_user. - */ -#define KERNEL_SYSCALL(ret, syscall, args...) \ -{ \ - mm_segment_t old_fs = get_fs(); \ - set_fs(KERNEL_DS); \ - ret = syscall(args); \ - set_fs (old_fs); \ -} - -#endif diff --git a/arch/parisc/kernel/sys_parisc32.c b/arch/parisc/kernel/sys_parisc32.c index a134ff4da12..bb9f3b64de5 100644 --- a/arch/parisc/kernel/sys_parisc32.c +++ b/arch/parisc/kernel/sys_parisc32.c @@ -42,8 +42,6 @@ #include #include -#include "sys32.h" - #undef DEBUG #ifdef DEBUG -- cgit v1.2.3-70-g09d2 From dd5e6d6a3db09b16b7c222943977865eead88cc3 Mon Sep 17 00:00:00 2001 From: Thomas Bogendoerfer Date: Tue, 30 Jul 2013 02:02:16 +0200 Subject: parisc: Fix interrupt routing for C8000 serial ports We can't use dev->mod_index for selecting the interrupt routing entry, because it's not an index into interrupt routing table. It will be even wrong on a machine with 2 CPUs (4 cores). But all needed information is contained in the PAT entries for the serial ports. mod[0] contains the iosapic address and mod_info has some indications for the interrupt input (at least it looks like it). This patch implements the searching for the right iosapic and uses this interrupt input information. Signed-off-by: Thomas Bogendoerfer Cc: # 3.10 Signed-off-by: Helge Deller --- arch/parisc/include/asm/parisc-device.h | 3 +++ arch/parisc/kernel/inventory.c | 1 + drivers/parisc/iosapic.c | 38 +++++++++++++++++++++++---------- drivers/tty/serial/8250/8250_gsc.c | 3 +-- 4 files changed, 32 insertions(+), 13 deletions(-) (limited to 'arch') diff --git a/arch/parisc/include/asm/parisc-device.h b/arch/parisc/include/asm/parisc-device.h index 9afdad6c2ff..eaf4dc1c729 100644 --- a/arch/parisc/include/asm/parisc-device.h +++ b/arch/parisc/include/asm/parisc-device.h @@ -23,6 +23,7 @@ struct parisc_device { /* generic info returned from pdc_pat_cell_module() */ unsigned long mod_info; /* PAT specific - Misc Module info */ unsigned long pmod_loc; /* physical Module location */ + unsigned long mod0; #endif u64 dma_mask; /* DMA mask for I/O */ struct device dev; @@ -61,4 +62,6 @@ parisc_get_drvdata(struct parisc_device *d) extern struct bus_type parisc_bus_type; +int iosapic_serial_irq(struct parisc_device *dev); + #endif /*_ASM_PARISC_PARISC_DEVICE_H_*/ diff --git a/arch/parisc/kernel/inventory.c b/arch/parisc/kernel/inventory.c index 3295ef4a185..f0b6722fc70 100644 --- a/arch/parisc/kernel/inventory.c +++ b/arch/parisc/kernel/inventory.c @@ -211,6 +211,7 @@ pat_query_module(ulong pcell_loc, ulong mod_index) /* REVISIT: who is the consumer of this? not sure yet... */ dev->mod_info = pa_pdc_cell->mod_info; /* pass to PAT_GET_ENTITY() */ dev->pmod_loc = pa_pdc_cell->mod_location; + dev->mod0 = pa_pdc_cell->mod[0]; register_parisc_device(dev); /* advertise device */ diff --git a/drivers/parisc/iosapic.c b/drivers/parisc/iosapic.c index e79e006eb9a..9ee04b4b68b 100644 --- a/drivers/parisc/iosapic.c +++ b/drivers/parisc/iosapic.c @@ -811,18 +811,28 @@ int iosapic_fixup_irq(void *isi_obj, struct pci_dev *pcidev) return pcidev->irq; } -static struct iosapic_info *first_isi = NULL; +static struct iosapic_info *iosapic_list; #ifdef CONFIG_64BIT -int iosapic_serial_irq(int num) +int iosapic_serial_irq(struct parisc_device *dev) { - struct iosapic_info *isi = first_isi; - struct irt_entry *irte = NULL; /* only used if PAT PDC */ + struct iosapic_info *isi; + struct irt_entry *irte; struct vector_info *vi; - int isi_line; /* line used by device */ + int cnt; + int intin; + + intin = (dev->mod_info >> 24) & 15; /* lookup IRT entry for isi/slot/pin set */ - irte = &irt_cell[num]; + for (cnt = 0; cnt < irt_num_entry; cnt++) { + irte = &irt_cell[cnt]; + if (COMPARE_IRTE_ADDR(irte, dev->mod0) && + irte->dest_iosapic_intin == intin) + break; + } + if (cnt >= irt_num_entry) + return 0; /* no irq found, force polling */ DBG_IRT("iosapic_serial_irq(): irte %p %x %x %x %x %x %x %x %x\n", irte, @@ -834,11 +844,17 @@ int iosapic_serial_irq(int num) irte->src_seg_id, irte->dest_iosapic_intin, (u32) irte->dest_iosapic_addr); - isi_line = irte->dest_iosapic_intin; + + /* search for iosapic */ + for (isi = iosapic_list; isi; isi = isi->isi_next) + if (isi->isi_hpa == dev->mod0) + break; + if (!isi) + return 0; /* no iosapic found, force polling */ /* get vector info for this input line */ - vi = isi->isi_vector + isi_line; - DBG_IRT("iosapic_serial_irq: line %d vi 0x%p\n", isi_line, vi); + vi = isi->isi_vector + intin; + DBG_IRT("iosapic_serial_irq: line %d vi 0x%p\n", iosapic_intin, vi); /* If this IRQ line has already been setup, skip it */ if (vi->irte) @@ -941,8 +957,8 @@ void *iosapic_register(unsigned long hpa) vip->irqline = (unsigned char) cnt; vip->iosapic = isi; } - if (!first_isi) - first_isi = isi; + isi->isi_next = iosapic_list; + iosapic_list = isi; return isi; } diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c index bb91b4713eb..2e3ea1a70d7 100644 --- a/drivers/tty/serial/8250/8250_gsc.c +++ b/drivers/tty/serial/8250/8250_gsc.c @@ -31,9 +31,8 @@ static int __init serial_init_chip(struct parisc_device *dev) int err; #ifdef CONFIG_64BIT - extern int iosapic_serial_irq(int cellnum); if (!dev->irq && (dev->id.sversion == 0xad)) - dev->irq = iosapic_serial_irq(dev->mod_index-1); + dev->irq = iosapic_serial_irq(dev); #endif if (!dev->irq) { -- cgit v1.2.3-70-g09d2 From e8e813ed268d90c1377f53460527c419eb52c67a Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Tue, 4 Jun 2013 14:21:17 +1000 Subject: powerpc: Rename PMU interrupts from CNT to PMI Back in commit 89713ed "Add timer, performance monitor and machine check counts to /proc/interrupts" we added a count of PMU interrupts to the output of /proc/interrupts. At the time we named them "CNT" to match x86. However in commit 89ccf46 "Rename 'performance counter interrupt'", the x86 guys renamed theirs from "CNT" to "PMI". Arguably changing the name could break someone's script, but I think the chance of that is minimal, and it's preferable to have a name that 1) is somewhat meaningful, and 2) matches x86. Signed-off-by: Michael Ellerman Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/irq.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/irq.c b/arch/powerpc/kernel/irq.c index 2e51cde616d..c69440cef7a 100644 --- a/arch/powerpc/kernel/irq.c +++ b/arch/powerpc/kernel/irq.c @@ -362,7 +362,7 @@ int arch_show_interrupts(struct seq_file *p, int prec) seq_printf(p, "%10u ", per_cpu(irq_stat, j).spurious_irqs); seq_printf(p, " Spurious interrupts\n"); - seq_printf(p, "%*s: ", prec, "CNT"); + seq_printf(p, "%*s: ", prec, "PMI"); for_each_online_cpu(j) seq_printf(p, "%10u ", per_cpu(irq_stat, j).pmu_irqs); seq_printf(p, " Performance monitoring interrupts\n"); -- cgit v1.2.3-70-g09d2 From 8d7c55d01e4648605fd0dacc82d8d3989ead4db7 Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Tue, 23 Jul 2013 18:07:45 +1000 Subject: powerpc/perf: Export PERF_EVENT_CONFIG_EBB_SHIFT to userspace We use bit 63 of the event code for userspace to request that the event be counted using EBB (Event Based Branches). Export this value, making it part of the API - though only on processors that support EBB. Signed-off-by: Michael Ellerman Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/perf_event_server.h | 6 +----- arch/powerpc/include/uapi/asm/Kbuild | 1 + arch/powerpc/include/uapi/asm/perf_event.h | 18 ++++++++++++++++++ arch/powerpc/perf/core-book3s.c | 2 +- arch/powerpc/perf/power8-pmu.c | 6 +++--- 5 files changed, 24 insertions(+), 9 deletions(-) create mode 100644 arch/powerpc/include/uapi/asm/perf_event.h (limited to 'arch') diff --git a/arch/powerpc/include/asm/perf_event_server.h b/arch/powerpc/include/asm/perf_event_server.h index 2dd7bfc459b..8b249264475 100644 --- a/arch/powerpc/include/asm/perf_event_server.h +++ b/arch/powerpc/include/asm/perf_event_server.h @@ -12,6 +12,7 @@ #include #include #include +#include #define MAX_HWEVENTS 8 #define MAX_EVENT_ALTERNATIVES 8 @@ -69,11 +70,6 @@ struct power_pmu { #define PPMU_LIMITED_PMC_REQD 2 /* have to put this on a limited PMC */ #define PPMU_ONLY_COUNT_RUN 4 /* only counting in run state */ -/* - * We use the event config bit 63 as a flag to request EBB. - */ -#define EVENT_CONFIG_EBB_SHIFT 63 - extern int register_power_pmu(struct power_pmu *); struct pt_regs; diff --git a/arch/powerpc/include/uapi/asm/Kbuild b/arch/powerpc/include/uapi/asm/Kbuild index 5182c8622b5..48be855ef37 100644 --- a/arch/powerpc/include/uapi/asm/Kbuild +++ b/arch/powerpc/include/uapi/asm/Kbuild @@ -20,6 +20,7 @@ header-y += mman.h header-y += msgbuf.h header-y += nvram.h header-y += param.h +header-y += perf_event.h header-y += poll.h header-y += posix_types.h header-y += ps3fb.h diff --git a/arch/powerpc/include/uapi/asm/perf_event.h b/arch/powerpc/include/uapi/asm/perf_event.h new file mode 100644 index 00000000000..80a4d40cf5b --- /dev/null +++ b/arch/powerpc/include/uapi/asm/perf_event.h @@ -0,0 +1,18 @@ +/* + * Copyright 2013 Michael Ellerman, IBM Corp. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; version 2 of the + * License. + */ + +#ifndef _UAPI_ASM_POWERPC_PERF_EVENT_H +#define _UAPI_ASM_POWERPC_PERF_EVENT_H + +/* + * We use bit 63 of perf_event_attr.config as a flag to request EBB. + */ +#define PERF_EVENT_CONFIG_EBB_SHIFT 63 + +#endif /* _UAPI_ASM_POWERPC_PERF_EVENT_H */ diff --git a/arch/powerpc/perf/core-book3s.c b/arch/powerpc/perf/core-book3s.c index 24a45f91c65..eeae308cf98 100644 --- a/arch/powerpc/perf/core-book3s.c +++ b/arch/powerpc/perf/core-book3s.c @@ -484,7 +484,7 @@ static bool is_ebb_event(struct perf_event *event) * use bit 63 of the event code for something else if they wish. */ return (ppmu->flags & PPMU_EBB) && - ((event->attr.config >> EVENT_CONFIG_EBB_SHIFT) & 1); + ((event->attr.config >> PERF_EVENT_CONFIG_EBB_SHIFT) & 1); } static int ebb_event_check(struct perf_event *event) diff --git a/arch/powerpc/perf/power8-pmu.c b/arch/powerpc/perf/power8-pmu.c index 7466374d278..2ee4a707f0d 100644 --- a/arch/powerpc/perf/power8-pmu.c +++ b/arch/powerpc/perf/power8-pmu.c @@ -118,7 +118,7 @@ (EVENT_UNIT_MASK << EVENT_UNIT_SHIFT) | \ (EVENT_COMBINE_MASK << EVENT_COMBINE_SHIFT) | \ (EVENT_MARKED_MASK << EVENT_MARKED_SHIFT) | \ - (EVENT_EBB_MASK << EVENT_CONFIG_EBB_SHIFT) | \ + (EVENT_EBB_MASK << PERF_EVENT_CONFIG_EBB_SHIFT) | \ EVENT_PSEL_MASK) /* MMCRA IFM bits - POWER8 */ @@ -233,10 +233,10 @@ static int power8_get_constraint(u64 event, unsigned long *maskp, unsigned long pmc = (event >> EVENT_PMC_SHIFT) & EVENT_PMC_MASK; unit = (event >> EVENT_UNIT_SHIFT) & EVENT_UNIT_MASK; cache = (event >> EVENT_CACHE_SEL_SHIFT) & EVENT_CACHE_SEL_MASK; - ebb = (event >> EVENT_CONFIG_EBB_SHIFT) & EVENT_EBB_MASK; + ebb = (event >> PERF_EVENT_CONFIG_EBB_SHIFT) & EVENT_EBB_MASK; /* Clear the EBB bit in the event, so event checks work below */ - event &= ~(EVENT_EBB_MASK << EVENT_CONFIG_EBB_SHIFT); + event &= ~(EVENT_EBB_MASK << PERF_EVENT_CONFIG_EBB_SHIFT); if (pmc) { if (pmc > 6) -- cgit v1.2.3-70-g09d2 From 3be7db6ab45b21345386d1a466da133b19cde5e4 Mon Sep 17 00:00:00 2001 From: Robert Jennings Date: Wed, 24 Jul 2013 20:13:21 -0500 Subject: powerpc: VPHN topology change updates all siblings When an associativity level change is found for one thread, the siblings threads need to be updated as well. This is done today for PRRN in stage_topology_update() but is missing for VPHN in update_cpu_associativity_changes_mask(). This patch will correctly update all thread siblings during a topology change. Without this patch a topology update can result in a CPU in init_sched_groups_power() getting stuck indefinitely in a loop. This loop is built in build_sched_groups(). As a result of the thread moving to a node separate from its siblings the struct sched_group will have its next pointer set to point to itself rather than the sched_group struct of the next thread. This happens because we have a domain without the SD_OVERLAP flag, which is correct, and a topology that doesn't conform with reality (threads on the same core assigned to different numa nodes). When this list is traversed by init_sched_groups_power() it will reach the thread's sched_group structure and loop indefinitely; the cpu will be stuck at this point. The bug was exposed when VPHN was enabled in commit b7abef0 (v3.9). Cc: [v3.9+] Reported-by: Jan Stancek Signed-off-by: Robert Jennings Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/smp.h | 4 +++ arch/powerpc/mm/numa.c | 59 +++++++++++++++++++++++++++++++----------- 2 files changed, 48 insertions(+), 15 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/smp.h b/arch/powerpc/include/asm/smp.h index ffbaabebcdc..48cfc858abd 100644 --- a/arch/powerpc/include/asm/smp.h +++ b/arch/powerpc/include/asm/smp.h @@ -145,6 +145,10 @@ extern void __cpu_die(unsigned int cpu); #define smp_setup_cpu_maps() static inline void inhibit_secondary_onlining(void) {} static inline void uninhibit_secondary_onlining(void) {} +static inline const struct cpumask *cpu_sibling_mask(int cpu) +{ + return cpumask_of(cpu); +} #endif /* CONFIG_SMP */ diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c index 08397217e8a..5850798826c 100644 --- a/arch/powerpc/mm/numa.c +++ b/arch/powerpc/mm/numa.c @@ -27,6 +27,7 @@ #include #include #include +#include #include #include #include @@ -1318,7 +1319,8 @@ static int update_cpu_associativity_changes_mask(void) } } if (changed) { - cpumask_set_cpu(cpu, changes); + cpumask_or(changes, changes, cpu_sibling_mask(cpu)); + cpu = cpu_last_thread_sibling(cpu); } } @@ -1426,7 +1428,7 @@ static int update_cpu_topology(void *data) if (!data) return -EINVAL; - cpu = get_cpu(); + cpu = smp_processor_id(); for (update = data; update; update = update->next) { if (cpu != update->cpu) @@ -1446,12 +1448,12 @@ static int update_cpu_topology(void *data) */ int arch_update_cpu_topology(void) { - unsigned int cpu, changed = 0; + unsigned int cpu, sibling, changed = 0; struct topology_update_data *updates, *ud; unsigned int associativity[VPHN_ASSOC_BUFSIZE] = {0}; cpumask_t updated_cpus; struct device *dev; - int weight, i = 0; + int weight, new_nid, i = 0; weight = cpumask_weight(&cpu_associativity_changes_mask); if (!weight) @@ -1464,19 +1466,46 @@ int arch_update_cpu_topology(void) cpumask_clear(&updated_cpus); for_each_cpu(cpu, &cpu_associativity_changes_mask) { - ud = &updates[i++]; - ud->cpu = cpu; - vphn_get_associativity(cpu, associativity); - ud->new_nid = associativity_to_nid(associativity); - - if (ud->new_nid < 0 || !node_online(ud->new_nid)) - ud->new_nid = first_online_node; + /* + * If siblings aren't flagged for changes, updates list + * will be too short. Skip on this update and set for next + * update. + */ + if (!cpumask_subset(cpu_sibling_mask(cpu), + &cpu_associativity_changes_mask)) { + pr_info("Sibling bits not set for associativity " + "change, cpu%d\n", cpu); + cpumask_or(&cpu_associativity_changes_mask, + &cpu_associativity_changes_mask, + cpu_sibling_mask(cpu)); + cpu = cpu_last_thread_sibling(cpu); + continue; + } - ud->old_nid = numa_cpu_lookup_table[cpu]; - cpumask_set_cpu(cpu, &updated_cpus); + /* Use associativity from first thread for all siblings */ + vphn_get_associativity(cpu, associativity); + new_nid = associativity_to_nid(associativity); + if (new_nid < 0 || !node_online(new_nid)) + new_nid = first_online_node; + + if (new_nid == numa_cpu_lookup_table[cpu]) { + cpumask_andnot(&cpu_associativity_changes_mask, + &cpu_associativity_changes_mask, + cpu_sibling_mask(cpu)); + cpu = cpu_last_thread_sibling(cpu); + continue; + } - if (i < weight) - ud->next = &updates[i]; + for_each_cpu(sibling, cpu_sibling_mask(cpu)) { + ud = &updates[i++]; + ud->cpu = sibling; + ud->new_nid = new_nid; + ud->old_nid = numa_cpu_lookup_table[sibling]; + cpumask_set_cpu(sibling, &updated_cpus); + if (i < weight) + ud->next = &updates[i]; + } + cpu = cpu_last_thread_sibling(cpu); } stop_machine(update_cpu_topology, &updates[0], &updated_cpus); -- cgit v1.2.3-70-g09d2 From 48be69a026b2c17350a5ef18a1959a919f60be7d Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 24 Jul 2013 00:29:18 +0100 Subject: ARM: move signal handlers into a vdso-like page Move the signal handlers into a VDSO page rather than keeping them in the vectors page. This allows us to place them randomly within this page, and also map the page at a random location within userspace further protecting these code fragments from ROP attacks. The new VDSO page is also poisoned in the same way as the vector page. Signed-off-by: Russell King --- arch/arm/include/asm/elf.h | 4 ++++ arch/arm/include/asm/mmu.h | 1 + arch/arm/kernel/process.c | 40 ++++++++++++++++++++++++++++++++--- arch/arm/kernel/signal.c | 52 +++++++++++++++++++++++++++++++++++++++------- arch/arm/kernel/signal.h | 12 ----------- arch/arm/kernel/traps.c | 9 -------- 6 files changed, 87 insertions(+), 31 deletions(-) delete mode 100644 arch/arm/kernel/signal.h (limited to 'arch') diff --git a/arch/arm/include/asm/elf.h b/arch/arm/include/asm/elf.h index 38050b1c480..9c9b30717fd 100644 --- a/arch/arm/include/asm/elf.h +++ b/arch/arm/include/asm/elf.h @@ -130,4 +130,8 @@ struct mm_struct; extern unsigned long arch_randomize_brk(struct mm_struct *mm); #define arch_randomize_brk arch_randomize_brk +#define ARCH_HAS_SETUP_ADDITIONAL_PAGES 1 +struct linux_binprm; +int arch_setup_additional_pages(struct linux_binprm *, int); + #endif diff --git a/arch/arm/include/asm/mmu.h b/arch/arm/include/asm/mmu.h index e3d55547e75..7345e37155d 100644 --- a/arch/arm/include/asm/mmu.h +++ b/arch/arm/include/asm/mmu.h @@ -8,6 +8,7 @@ typedef struct { atomic64_t id; #endif unsigned int vmalloc_seq; + unsigned long sigpage; } mm_context_t; #ifdef CONFIG_CPU_HAS_ASID diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index d3ca4f6915a..566d0d71a1e 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -428,8 +428,8 @@ unsigned long arch_randomize_brk(struct mm_struct *mm) #ifdef CONFIG_MMU /* * The vectors page is always readable from user space for the - * atomic helpers and the signal restart code. Insert it into the - * gate_vma so that it is visible through ptrace and /proc//mem. + * atomic helpers. Insert it into the gate_vma so that it is visible + * through ptrace and /proc//mem. */ static struct vm_area_struct gate_vma = { .vm_start = 0xffff0000, @@ -461,6 +461,40 @@ int in_gate_area_no_mm(unsigned long addr) const char *arch_vma_name(struct vm_area_struct *vma) { - return (vma == &gate_vma) ? "[vectors]" : NULL; + return (vma == &gate_vma) ? "[vectors]" : + (vma->vm_mm && vma->vm_start == vma->vm_mm->context.sigpage) ? + "[sigpage]" : NULL; +} + +extern struct page *get_signal_page(void); + +int arch_setup_additional_pages(struct linux_binprm *bprm, int uses_interp) +{ + struct mm_struct *mm = current->mm; + struct page *page; + unsigned long addr; + int ret; + + page = get_signal_page(); + if (!page) + return -ENOMEM; + + down_write(&mm->mmap_sem); + addr = get_unmapped_area(NULL, 0, PAGE_SIZE, 0, 0); + if (IS_ERR_VALUE(addr)) { + ret = addr; + goto up_fail; + } + + ret = install_special_mapping(mm, addr, PAGE_SIZE, + VM_READ | VM_EXEC | VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC, + &page); + + if (ret == 0) + mm->context.sigpage = addr; + + up_fail: + up_write(&mm->mmap_sem); + return ret; } #endif diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c index 1c16c35c271..0f17e06d51e 100644 --- a/arch/arm/kernel/signal.c +++ b/arch/arm/kernel/signal.c @@ -8,6 +8,7 @@ * published by the Free Software Foundation. */ #include +#include #include #include #include @@ -15,12 +16,11 @@ #include #include +#include #include #include #include -#include "signal.h" - /* * For ARM syscalls, we encode the syscall number into the instruction. */ @@ -40,11 +40,13 @@ #define SWI_THUMB_SIGRETURN (0xdf00 << 16 | 0x2700 | (__NR_sigreturn - __NR_SYSCALL_BASE)) #define SWI_THUMB_RT_SIGRETURN (0xdf00 << 16 | 0x2700 | (__NR_rt_sigreturn - __NR_SYSCALL_BASE)) -const unsigned long sigreturn_codes[7] = { +static const unsigned long sigreturn_codes[7] = { MOV_R7_NR_SIGRETURN, SWI_SYS_SIGRETURN, SWI_THUMB_SIGRETURN, MOV_R7_NR_RT_SIGRETURN, SWI_SYS_RT_SIGRETURN, SWI_THUMB_RT_SIGRETURN, }; +static unsigned long signal_return_offset; + #ifdef CONFIG_CRUNCH static int preserve_crunch_context(struct crunch_sigframe __user *frame) { @@ -401,12 +403,15 @@ setup_return(struct pt_regs *regs, struct ksignal *ksig, return 1; if ((cpsr & MODE32_BIT) && !IS_ENABLED(CONFIG_ARM_MPU)) { + struct mm_struct *mm = current->mm; + /* - * 32-bit code can use the new high-page - * signal return code support except when the MPU has - * protected the vectors page from PL0 + * 32-bit code can use the signal return page + * except when the MPU has protected the vectors + * page from PL0 */ - retcode = KERN_SIGRETURN_CODE + (idx << 2) + thumb; + retcode = mm->context.sigpage + signal_return_offset + + (idx << 2) + thumb; } else { /* * Ensure that the instruction cache sees @@ -608,3 +613,36 @@ do_work_pending(struct pt_regs *regs, unsigned int thread_flags, int syscall) } while (thread_flags & _TIF_WORK_MASK); return 0; } + +static struct page *signal_page; + +struct page *get_signal_page(void) +{ + if (!signal_page) { + unsigned long ptr; + unsigned offset; + void *addr; + + signal_page = alloc_pages(GFP_KERNEL, 0); + + if (!signal_page) + return NULL; + + addr = page_address(signal_page); + + /* Give the signal return code some randomness */ + offset = 0x200 + (get_random_int() & 0x7fc); + signal_return_offset = offset; + + /* + * Copy signal return handlers into the vector page, and + * set sigreturn to be a pointer to these. + */ + memcpy(addr + offset, sigreturn_codes, sizeof(sigreturn_codes)); + + ptr = (unsigned long)addr + offset; + flush_icache_range(ptr, ptr + sizeof(sigreturn_codes)); + } + + return signal_page; +} diff --git a/arch/arm/kernel/signal.h b/arch/arm/kernel/signal.h deleted file mode 100644 index 5ff067b7c75..00000000000 --- a/arch/arm/kernel/signal.h +++ /dev/null @@ -1,12 +0,0 @@ -/* - * linux/arch/arm/kernel/signal.h - * - * Copyright (C) 2005-2009 Russell King. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#define KERN_SIGRETURN_CODE (CONFIG_VECTORS_BASE + 0x00000500) - -extern const unsigned long sigreturn_codes[7]; diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index e3ca35ccd38..ab517fcce21 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -35,8 +35,6 @@ #include #include -#include "signal.h" - static const char *handler[]= { "prefetch abort", "data abort", "address exception", "interrupt" }; void *vectors_page; @@ -850,13 +848,6 @@ void __init early_trap_init(void *vectors_base) kuser_init(vectors_base); - /* - * Copy signal return handlers into the vector page, and - * set sigreturn to be a pointer to these. - */ - memcpy((void *)(vectors + KERN_SIGRETURN_CODE - CONFIG_VECTORS_BASE), - sigreturn_codes, sizeof(sigreturn_codes)); - flush_icache_range(vectors, vectors + PAGE_SIZE * 2); modify_domain(DOMAIN_USER, DOMAIN_CLIENT); #else /* ifndef CONFIG_CPU_V7M */ -- cgit v1.2.3-70-g09d2 From a5463cd3435475386cbbe7b06e01292ac169d36f Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 31 Jul 2013 21:58:56 +0100 Subject: ARM: make vectors page inaccessible from userspace If kuser helpers are not provided by the kernel, disable user access to the vectors page. With the kuser helpers gone, there is no reason for this page to be visible to userspace. Signed-off-by: Russell King --- arch/arm/include/asm/page.h | 2 ++ arch/arm/kernel/process.c | 7 ++++++- arch/arm/mm/mmu.c | 4 ++++ 3 files changed, 12 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/include/asm/page.h b/arch/arm/include/asm/page.h index 6363f3d1d50..4355f0ec44d 100644 --- a/arch/arm/include/asm/page.h +++ b/arch/arm/include/asm/page.h @@ -142,7 +142,9 @@ extern void __cpu_copy_user_highpage(struct page *to, struct page *from, #define clear_page(page) memset((void *)(page), 0, PAGE_SIZE) extern void copy_page(void *to, const void *from); +#ifdef CONFIG_KUSER_HELPERS #define __HAVE_ARCH_GATE_AREA 1 +#endif #ifdef CONFIG_ARM_LPAE #include diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 566d0d71a1e..1e6c33d01c0 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -426,6 +426,7 @@ unsigned long arch_randomize_brk(struct mm_struct *mm) } #ifdef CONFIG_MMU +#ifdef CONFIG_KUSER_HELPERS /* * The vectors page is always readable from user space for the * atomic helpers. Insert it into the gate_vma so that it is visible @@ -458,10 +459,14 @@ int in_gate_area_no_mm(unsigned long addr) { return in_gate_area(NULL, addr); } +#define is_gate_vma(vma) ((vma) = &gate_vma) +#else +#define is_gate_vma(vma) 0 +#endif const char *arch_vma_name(struct vm_area_struct *vma) { - return (vma == &gate_vma) ? "[vectors]" : + return is_gate_vma(vma) ? "[vectors]" : (vma->vm_mm && vma->vm_start == vma->vm_mm->context.sigpage) ? "[sigpage]" : NULL; } diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 9ea274d1af6..ca46f413d86 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -1205,7 +1205,11 @@ static void __init devicemaps_init(struct machine_desc *mdesc) map.pfn = __phys_to_pfn(virt_to_phys(vectors)); map.virtual = 0xffff0000; map.length = PAGE_SIZE; +#ifdef CONFIG_KUSER_HELPERS map.type = MT_HIGH_VECTORS; +#else + map.type = MT_LOW_VECTORS; +#endif create_mapping(&map); if (!vectors_high()) { -- cgit v1.2.3-70-g09d2 From 44424c34049f41123a3a8b4853822f47f4ff03a2 Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Tue, 30 Jul 2013 23:09:46 +0100 Subject: ARM: 7803/1: Fix deadlock scenario with smp_send_stop() If one process calls sys_reboot and that process then stops other CPUs while those CPUs are within a spin_lock() region we can potentially encounter a deadlock scenario like below. CPU 0 CPU 1 ----- ----- spin_lock(my_lock) smp_send_stop() handle_IPI() disable_preemption/irqs while(1); spin_lock(my_lock) <--- Waits forever We shouldn't attempt to run any other tasks after we send a stop IPI to a CPU so disable preemption so that this task runs to completion. We use local_irq_disable() here for cross-arch consistency with x86. Reported-by: Sundarajan Srinivasan Signed-off-by: Stephen Boyd Signed-off-by: Russell King --- arch/arm/kernel/process.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index d3ca4f6915a..08b47ebd314 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -197,6 +197,7 @@ void machine_shutdown(void) */ void machine_halt(void) { + local_irq_disable(); smp_send_stop(); local_irq_disable(); @@ -211,6 +212,7 @@ void machine_halt(void) */ void machine_power_off(void) { + local_irq_disable(); smp_send_stop(); if (pm_power_off) @@ -230,6 +232,7 @@ void machine_power_off(void) */ void machine_restart(char *cmd) { + local_irq_disable(); smp_send_stop(); arm_pm_restart(reboot_mode, cmd); -- cgit v1.2.3-70-g09d2 From 2449189bb7c73b5fe55a18bc0d289e39bdcd4998 Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 31 Jul 2013 11:37:17 +0100 Subject: ARM: Add .text annotations where required after __CPUINIT removal Commit 8bd26e3a7 (arm: delete __cpuinit/__CPUINIT usage from all ARM users) caused some code to leak into sections which are discarded through the removal of __CPUINIT annotations. Add appropriate .text annotations to bring these back into the kernel text. Signed-off-by: Russell King --- arch/arm/kernel/head-nommu.S | 1 + arch/arm/kernel/head.S | 1 + 2 files changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/kernel/head-nommu.S b/arch/arm/kernel/head-nommu.S index b361de14375..14235ba64a9 100644 --- a/arch/arm/kernel/head-nommu.S +++ b/arch/arm/kernel/head-nommu.S @@ -87,6 +87,7 @@ ENTRY(stext) ENDPROC(stext) #ifdef CONFIG_SMP + .text ENTRY(secondary_startup) /* * Common entry point for secondary CPUs. diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S index 9cf6063020a..2c7cc1e0347 100644 --- a/arch/arm/kernel/head.S +++ b/arch/arm/kernel/head.S @@ -343,6 +343,7 @@ __turn_mmu_on_loc: .long __turn_mmu_on_end #if defined(CONFIG_SMP) + .text ENTRY(secondary_startup) /* * Common entry point for secondary CPUs. -- cgit v1.2.3-70-g09d2 From 70a0f6032985f156bd7e957cfec99c3dd3d592a2 Mon Sep 17 00:00:00 2001 From: Tomi Valkeinen Date: Tue, 23 Jul 2013 10:57:47 +0300 Subject: ARM: OMAP: dss-common: fix Panda's DVI DDC channel Panda's DVI connector's DDC pins are connected to OMAP's third i2c bus. With non-DT, the bus number was 3, and that is what is used in the dss-common.c which contains the platform data for Panda's DVI. However, with DT, the bus number is 2. As we now only have DT boot for Panda, we have to change the bus number to make DVI EDID read operational. Signed-off-by: Tomi Valkeinen Acked-by: Tony Lindgren --- arch/arm/mach-omap2/dss-common.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/dss-common.c b/arch/arm/mach-omap2/dss-common.c index 393aeefaebb..043e5705f2a 100644 --- a/arch/arm/mach-omap2/dss-common.c +++ b/arch/arm/mach-omap2/dss-common.c @@ -42,7 +42,7 @@ /* Using generic display panel */ static struct tfp410_platform_data omap4_dvi_panel = { - .i2c_bus_num = 3, + .i2c_bus_num = 2, .power_down_gpio = PANDA_DVI_TFP410_POWER_DOWN_GPIO, }; -- cgit v1.2.3-70-g09d2 From e0d407564b532d978b03ceccebd224a05d02f111 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 3 Aug 2013 10:30:05 +0100 Subject: ARM: fix a cockup in 48be69a02 (ARM: move signal handlers into a vdso-like page) Unfortunately, I never committed the fix to a nasty oops which can occur as a result of that commit: ------------[ cut here ]------------ kernel BUG at /home/olof/work/batch/include/linux/mm.h:414! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 490 Comm: killall5 Not tainted 3.11.0-rc3-00288-gabe0308 #53 task: e90acac0 ti: e9be8000 task.ti: e9be8000 PC is at special_mapping_fault+0xa4/0xc4 LR is at __do_fault+0x68/0x48c This doesn't show up unless you do quite a bit of testing; a simple boot test does not do this, so all my nightly tests were passing fine. The reason for this is that install_special_mapping() expects the page array to stick around, and as this was only inserting one page which was stored on the kernel stack, that's why this was blowing up. Reported-by: Olof Johansson Tested-by: Olof Johansson Signed-off-by: Russell King --- arch/arm/kernel/process.c | 9 +++++---- arch/arm/kernel/signal.c | 41 +++++++++++++++++++---------------------- 2 files changed, 24 insertions(+), 26 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 1e6c33d01c0..d03b5bd889c 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -471,17 +471,18 @@ const char *arch_vma_name(struct vm_area_struct *vma) "[sigpage]" : NULL; } +static struct page *signal_page; extern struct page *get_signal_page(void); int arch_setup_additional_pages(struct linux_binprm *bprm, int uses_interp) { struct mm_struct *mm = current->mm; - struct page *page; unsigned long addr; int ret; - page = get_signal_page(); - if (!page) + if (!signal_page) + signal_page = get_signal_page(); + if (!signal_page) return -ENOMEM; down_write(&mm->mmap_sem); @@ -493,7 +494,7 @@ int arch_setup_additional_pages(struct linux_binprm *bprm, int uses_interp) ret = install_special_mapping(mm, addr, PAGE_SIZE, VM_READ | VM_EXEC | VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC, - &page); + &signal_page); if (ret == 0) mm->context.sigpage = addr; diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c index 0f17e06d51e..39e7105a9b7 100644 --- a/arch/arm/kernel/signal.c +++ b/arch/arm/kernel/signal.c @@ -614,35 +614,32 @@ do_work_pending(struct pt_regs *regs, unsigned int thread_flags, int syscall) return 0; } -static struct page *signal_page; - struct page *get_signal_page(void) { - if (!signal_page) { - unsigned long ptr; - unsigned offset; - void *addr; + unsigned long ptr; + unsigned offset; + struct page *page; + void *addr; - signal_page = alloc_pages(GFP_KERNEL, 0); + page = alloc_pages(GFP_KERNEL, 0); - if (!signal_page) - return NULL; + if (!page) + return NULL; - addr = page_address(signal_page); + addr = page_address(page); - /* Give the signal return code some randomness */ - offset = 0x200 + (get_random_int() & 0x7fc); - signal_return_offset = offset; + /* Give the signal return code some randomness */ + offset = 0x200 + (get_random_int() & 0x7fc); + signal_return_offset = offset; - /* - * Copy signal return handlers into the vector page, and - * set sigreturn to be a pointer to these. - */ - memcpy(addr + offset, sigreturn_codes, sizeof(sigreturn_codes)); + /* + * Copy signal return handlers into the vector page, and + * set sigreturn to be a pointer to these. + */ + memcpy(addr + offset, sigreturn_codes, sizeof(sigreturn_codes)); - ptr = (unsigned long)addr + offset; - flush_icache_range(ptr, ptr + sizeof(sigreturn_codes)); - } + ptr = (unsigned long)addr + offset; + flush_icache_range(ptr, ptr + sizeof(sigreturn_codes)); - return signal_page; + return page; } -- cgit v1.2.3-70-g09d2 From 8c0cc8a5d90bc7373a7a9e7f7a40eb41f51e03fc Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 3 Aug 2013 10:39:51 +0100 Subject: ARM: fix nommu builds with 48be69a02 (ARM: move signal handlers into a vdso-like page) Olof reports that noMMU builds error out with: arch/arm/kernel/signal.c: In function 'setup_return': arch/arm/kernel/signal.c:413:25: error: 'mm_context_t' has no member named 'sigpage' This shows one of the evilnesses of IS_ENABLED(). Get rid of it here and replace it with #ifdef's - and as no noMMU platform can make use of sigpage, depend on CONIFG_MMU not CONFIG_ARM_MPU. Reported-by: Olof Johansson Signed-off-by: Russell King --- arch/arm/include/asm/elf.h | 2 ++ arch/arm/kernel/signal.c | 7 +++++-- 2 files changed, 7 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/include/asm/elf.h b/arch/arm/include/asm/elf.h index 9c9b30717fd..56211f2084e 100644 --- a/arch/arm/include/asm/elf.h +++ b/arch/arm/include/asm/elf.h @@ -130,8 +130,10 @@ struct mm_struct; extern unsigned long arch_randomize_brk(struct mm_struct *mm); #define arch_randomize_brk arch_randomize_brk +#ifdef CONFIG_MMU #define ARCH_HAS_SETUP_ADDITIONAL_PAGES 1 struct linux_binprm; int arch_setup_additional_pages(struct linux_binprm *, int); +#endif #endif diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c index 39e7105a9b7..ab330422527 100644 --- a/arch/arm/kernel/signal.c +++ b/arch/arm/kernel/signal.c @@ -402,7 +402,8 @@ setup_return(struct pt_regs *regs, struct ksignal *ksig, __put_user(sigreturn_codes[idx+1], rc+1)) return 1; - if ((cpsr & MODE32_BIT) && !IS_ENABLED(CONFIG_ARM_MPU)) { +#ifdef CONFIG_MMU + if (cpsr & MODE32_BIT) { struct mm_struct *mm = current->mm; /* @@ -412,7 +413,9 @@ setup_return(struct pt_regs *regs, struct ksignal *ksig, */ retcode = mm->context.sigpage + signal_return_offset + (idx << 2) + thumb; - } else { + } else +#endif + { /* * Ensure that the instruction cache sees * the return code written onto the stack. -- cgit v1.2.3-70-g09d2 From 95e8ce69a043bc501b45508cc31f1dc9a3f64d3e Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Thu, 1 Aug 2013 13:13:31 +0100 Subject: ARM: STi: Fix cpu nodes with correct device_type. This patch fixes cpu nodes with device_type = "cpu". This change was not necessary before 3.10-rc7. Without this patch STi SOCs does not boot as SMP. Signed-off-by: Srinivas Kandagatla Signed-off-by: Olof Johansson --- arch/arm/boot/dts/stih41x.dtsi | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/stih41x.dtsi b/arch/arm/boot/dts/stih41x.dtsi index 7321403cab8..f5b9898d9c6 100644 --- a/arch/arm/boot/dts/stih41x.dtsi +++ b/arch/arm/boot/dts/stih41x.dtsi @@ -6,10 +6,12 @@ #address-cells = <1>; #size-cells = <0>; cpu@0 { + device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; }; cpu@1 { + device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; }; -- cgit v1.2.3-70-g09d2 From d6f67eb787cd9a5d7af2aaac403ea117578af6c9 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Thu, 1 Aug 2013 13:13:41 +0100 Subject: ARM: STi: remove sti_secondary_start from INIT section. This patch removes sti_secondary_start from _INIT section, there are 2 reason for this removal. 1. discarding such a small code does not save much, given the RAM sizes. 2. Having this code discarded, creates corruption issue when we boot smp-kernel with nrcpus=1 or with single cpu node in DT. Signed-off-by: Srinivas Kandagatla Signed-off-by: Olof Johansson --- arch/arm/mach-sti/headsmp.S | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-sti/headsmp.S b/arch/arm/mach-sti/headsmp.S index 78ebc7559f5..4c09bae86ed 100644 --- a/arch/arm/mach-sti/headsmp.S +++ b/arch/arm/mach-sti/headsmp.S @@ -16,8 +16,6 @@ #include #include - __INIT - /* * ST specific entry point for secondary CPUs. This provides * a "holding pen" into which all secondary cores are held until we're -- cgit v1.2.3-70-g09d2 From a1632ad35c37a8bd7bd22dd601906bfef90ad3a6 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Tue, 23 Jul 2013 11:11:45 -0700 Subject: ARM: tegra: enable ULPI phy on Colibri T20 This was missed when splitting out the phy from the controller node in commit 9dffe3be3f32 (ARM: tegra: modify ULPI reset GPIO properties). Signed-off-by: Lucas Stach Signed-off-by: Stephen Warren Signed-off-by: Olof Johansson --- arch/arm/boot/dts/tegra20-colibri-512.dtsi | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/tegra20-colibri-512.dtsi b/arch/arm/boot/dts/tegra20-colibri-512.dtsi index 2fcb3f2ca16..5592be6f2f7 100644 --- a/arch/arm/boot/dts/tegra20-colibri-512.dtsi +++ b/arch/arm/boot/dts/tegra20-colibri-512.dtsi @@ -457,6 +457,7 @@ }; usb-phy@c5004000 { + status = "okay"; nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>; }; -- cgit v1.2.3-70-g09d2 From 3ac3bcb9625dad4074cb67a8e319ea369d61dcdb Mon Sep 17 00:00:00 2001 From: Markos Chandras Date: Tue, 9 Jul 2013 09:21:35 +0100 Subject: MIPS: PNX833x: PNX8335_PCI_ETHERNET_INT depends on CONFIG_SOC_PNX8335 The PNX8335_PCI_ETHERNET_INT macro is defined in arch/mips/include/asm/mach-pnx833x/irq-mapping.h only if CONFIG_SOC_PNX8335 is selected. Fixes the following randconfig problem: arch/mips/pnx833x/common/platform.c:210:12: error: 'PNX8335_PIC_ETHERNET_INT' undeclared here (not in a function) Signed-off-by: Markos Chandras Acked-by: Steven J. Hill Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5585/ Signed-off-by: Ralf Baechle --- arch/mips/pnx833x/common/platform.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/mips/pnx833x/common/platform.c b/arch/mips/pnx833x/common/platform.c index d22dc0d6f28..2b7e837dc2e 100644 --- a/arch/mips/pnx833x/common/platform.c +++ b/arch/mips/pnx833x/common/platform.c @@ -206,11 +206,13 @@ static struct resource pnx833x_ethernet_resources[] = { .end = PNX8335_IP3902_PORTS_END, .flags = IORESOURCE_MEM, }, +#ifdef CONFIG_SOC_PNX8335 [1] = { .start = PNX8335_PIC_ETHERNET_INT, .end = PNX8335_PIC_ETHERNET_INT, .flags = IORESOURCE_IRQ, }, +#endif }; static struct platform_device pnx833x_ethernet_device = { -- cgit v1.2.3-70-g09d2 From cf5b2d23a75cbb53785d270e76e4911e84797b72 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Thu, 1 Aug 2013 18:31:05 +0200 Subject: MIPS: oprofile: Fix BUG due to smp_processor_id() in preemptible code. current_cpu_type() is not preemption-safe. If CONFIG_PREEMPT is enabled then mipsxx_reg_setup() can be called from preemptible state. Added get_cpu()/put_cpu() pair to make it preemption-safe. This was found while testing oprofile with CONFIG_DEBUG_PREEMPT enable. /usr/zntestsuite # opcontrol --init /usr/zntestsuite # opcontrol --setup --event=L2_CACHE_ACCESSES:500 --event=L2_CACHE_MISSES:500 --no-vmlinux /usr/zntestsuite # opcontrol --start Using 2.6+ OProfile kernel interface. BUG: using smp_processor_id() in preemptible [00000000] code: oprofiled/1362 caller is mipsxx_reg_setup+0x11c/0x164 CPU: 0 PID: 1362 Comm: oprofiled Not tainted 3.10.4 #18 Stack : 00000006 70757465 00000000 00000000 00000000 00000000 80b173f6 00000037 80b10000 00000000 80b21614 88f5a220 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 89c49c00 89c49c2c 80721254 807b7927 8012c1d0 80b10000 80721254 00000000 00000552 88f5a220 80b1335c 807b78e6 89c49ba8 ... Call Trace: [<801099a4>] show_stack+0x64/0x7c [<80665520>] dump_stack+0x20/0x2c [<803a2250>] debug_smp_processor_id+0xe0/0xf0 [<8052df24>] mipsxx_reg_setup+0x11c/0x164 [<8052cd70>] op_mips_setup+0x24/0x4c [<80529cfc>] oprofile_setup+0x5c/0x12c [<8052b9f8>] event_buffer_open+0x78/0xf8 [<801c3150>] do_dentry_open.isra.15+0x2b8/0x3b0 [<801c3270>] finish_open+0x28/0x4c [<801d49b8>] do_last.isra.41+0x2cc/0xd00 [<801d54a0>] path_openat+0xb4/0x4c4 [<801d5c44>] do_filp_open+0x3c/0xac [<801c4744>] do_sys_open+0x110/0x1f4 [<8010f47c>] stack_done+0x20/0x44 Bug reported and original patch by Jerin Jacob . Signed-off-by: Ralf Baechle Acked-by: Jerin Jacob --- arch/mips/include/asm/cpu-features.h | 2 ++ arch/mips/oprofile/op_model_mipsxx.c | 2 +- 2 files changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/include/asm/cpu-features.h b/arch/mips/include/asm/cpu-features.h index 1dc086087a7..fa44f3ec530 100644 --- a/arch/mips/include/asm/cpu-features.h +++ b/arch/mips/include/asm/cpu-features.h @@ -17,6 +17,8 @@ #define current_cpu_type() current_cpu_data.cputype #endif +#define boot_cpu_type() cpu_data[0].cputype + /* * SMP assumption: Options of CPU 0 are a superset of all processors. * This is true for all known MIPS systems. diff --git a/arch/mips/oprofile/op_model_mipsxx.c b/arch/mips/oprofile/op_model_mipsxx.c index e4b1140cdae..3a2b6e9f25c 100644 --- a/arch/mips/oprofile/op_model_mipsxx.c +++ b/arch/mips/oprofile/op_model_mipsxx.c @@ -166,7 +166,7 @@ static void mipsxx_reg_setup(struct op_counter_config *ctr) reg.control[i] |= M_PERFCTL_USER; if (ctr[i].exl) reg.control[i] |= M_PERFCTL_EXL; - if (current_cpu_type() == CPU_XLR) + if (boot_cpu_type() == CPU_XLR) reg.control[i] |= M_PERFCTL_COUNT_ALL_THREADS; reg.counter[i] = 0x80000000 - ctr[i].count; } -- cgit v1.2.3-70-g09d2 From fcfa66de8a2f0631a65a2cec0f6149dafd36ec81 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Mon, 5 Aug 2013 11:50:25 +0100 Subject: MIPS: BMIPS: fix hardware interrupt routing for boot CPU != 0 The hardware interrupt routing for boot CPU != 0 is wrong because it will route all the hardware interrupts to TP0 which is not the one we booted from. Fix this by properly checking which boot CPU we are booting from and updating the right interrupt mask for the boot CPU. This fixes booting on BCM3368 with bmips_smp_emabled = 0. Signed-off-by: Florian Fainelli Cc: linux-mips@linux-mips.org Cc: blogic@openwrt.org Cc: jogo@openwrt.org Cc: cernekee@gmail.com Patchwork: https://patchwork.linux-mips.org/patch/5650/ Signed-off-by: Ralf Baechle --- arch/mips/kernel/smp-bmips.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/mips/kernel/smp-bmips.c b/arch/mips/kernel/smp-bmips.c index 159abc8842d..126da74d4c5 100644 --- a/arch/mips/kernel/smp-bmips.c +++ b/arch/mips/kernel/smp-bmips.c @@ -66,6 +66,8 @@ static void __init bmips_smp_setup(void) int i, cpu = 1, boot_cpu = 0; #if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) + int cpu_hw_intr; + /* arbitration priority */ clear_c0_brcm_cmt_ctrl(0x30); @@ -80,8 +82,12 @@ static void __init bmips_smp_setup(void) * MIPS interrupt 2 (HW INT 0) is the CPU0 L1 controller output * MIPS interrupt 3 (HW INT 1) is the CPU1 L1 controller output */ - change_c0_brcm_cmt_intr(0xf8018000, - (0x02 << 27) | (0x03 << 15)); + if (boot_cpu == 0) + cpu_hw_intr = 0x02; + else + cpu_hw_intr = 0x1d; + + change_c0_brcm_cmt_intr(0xf8018000, (cpu_hw_intr << 27) | (0x03 << 15)); /* single core, 2 threads (2 pipelines) */ max_cpus = 2; -- cgit v1.2.3-70-g09d2 From c4afd7b95fff2f4964e630d0de90e8bc94ae37f1 Mon Sep 17 00:00:00 2001 From: Cong Ding Date: Sat, 27 Jul 2013 19:07:51 -0400 Subject: avr32: boards/atngw100/mrmt.c: fix building error there is an additional "{", which causes building error. Signed-off-by: Cong Ding Acked-by: Hans-Christian Egtvedt --- arch/avr32/boards/atngw100/mrmt.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/avr32/boards/atngw100/mrmt.c b/arch/avr32/boards/atngw100/mrmt.c index f9143196345..7de083d19b7 100644 --- a/arch/avr32/boards/atngw100/mrmt.c +++ b/arch/avr32/boards/atngw100/mrmt.c @@ -150,7 +150,6 @@ static struct ac97c_platform_data __initdata ac97c0_data = { static struct platform_device rmt_ts_device = { .name = "ucb1400_ts", .id = -1, - } }; #endif -- cgit v1.2.3-70-g09d2 From 4e90a2a7375e86827541bda9393414c03e7721c6 Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Wed, 31 Jul 2013 16:31:26 +1000 Subject: powerpc: On POWERNV enable PPC_DENORMALISATION by default We want PPC_DENORMALISATION enabled when POWERNV is enabled, so update the Kconfig. Signed-off-by: Anton Blanchard Acked-by: Michael Neuling Signed-off-by: Benjamin Herrenschmidt CC: --- arch/powerpc/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index 3bf72cd2c8f..dbd9d3c991e 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -566,7 +566,7 @@ config SCHED_SMT config PPC_DENORMALISATION bool "PowerPC denormalisation exception handling" depends on PPC_BOOK3S_64 - default "n" + default "y" if PPC_POWERNV ---help--- Add support for handling denormalisation of single precision values. Useful for bare metal only. If unsure say Y here. -- cgit v1.2.3-70-g09d2 From 7e76f34fa103677a27d96a7cfef8ce61389a32de Mon Sep 17 00:00:00 2001 From: Aruna Balakrishnaiah Date: Thu, 8 Aug 2013 22:33:49 +0530 Subject: powerpc/pseries: Fix buffer overflow when reading from pstore When reading from pstore there is a buffer overflow during decompression due to the header added in unzip_oops. Remove unzip_oops and call pstore_decompress directly in nvram_pstore_read. Allocate buffer of size report_length of the oops header as header will not be deallocated in pstore. Since we have 'openssl' command line tool to decompress the compressed data, dump the compressed data in case decompression fails instead of not dumping anything. Signed-off-by: Aruna Balakrishnaiah Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/nvram.c | 70 ++++++++++++---------------------- 1 file changed, 24 insertions(+), 46 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/nvram.c b/arch/powerpc/platforms/pseries/nvram.c index 9f8671a4455..893f36053c9 100644 --- a/arch/powerpc/platforms/pseries/nvram.c +++ b/arch/powerpc/platforms/pseries/nvram.c @@ -569,35 +569,6 @@ error: return ret; } -static int unzip_oops(char *oops_buf, char *big_buf) -{ - struct oops_log_info *oops_hdr = (struct oops_log_info *)oops_buf; - u64 timestamp = oops_hdr->timestamp; - char *big_oops_data = NULL; - char *oops_data_buf = NULL; - size_t big_oops_data_sz; - int unzipped_len; - - big_oops_data = big_buf + sizeof(struct oops_log_info); - big_oops_data_sz = big_oops_buf_sz - sizeof(struct oops_log_info); - oops_data_buf = oops_buf + sizeof(struct oops_log_info); - - unzipped_len = nvram_decompress(oops_data_buf, big_oops_data, - oops_hdr->report_length, - big_oops_data_sz); - - if (unzipped_len < 0) { - pr_err("nvram: decompression failed; returned %d\n", - unzipped_len); - return -1; - } - oops_hdr = (struct oops_log_info *)big_buf; - oops_hdr->version = OOPS_HDR_VERSION; - oops_hdr->report_length = (u16) unzipped_len; - oops_hdr->timestamp = timestamp; - return 0; -} - static int nvram_pstore_open(struct pstore_info *psi) { /* Reset the iterator to start reading partitions again */ @@ -685,10 +656,9 @@ static ssize_t nvram_pstore_read(u64 *id, enum pstore_type_id *type, unsigned int err_type, id_no, size = 0; struct nvram_os_partition *part = NULL; char *buff = NULL, *big_buff = NULL; - int rc, sig = 0; + int sig = 0; loff_t p; -read_partition: read_type++; switch (nvram_type_ids[read_type]) { @@ -749,30 +719,36 @@ read_partition: *id = id_no; if (nvram_type_ids[read_type] == PSTORE_TYPE_DMESG) { + int length, unzipped_len; + oops_hdr = (struct oops_log_info *)buff; - *buf = buff + sizeof(*oops_hdr); + length = oops_hdr->report_length; + *buf = kmalloc(length, GFP_KERNEL); + if (*buf == NULL) + return -ENOMEM; + memcpy(*buf, buff + sizeof(*oops_hdr), length); + time->tv_sec = oops_hdr->timestamp; + time->tv_nsec = 0; + kfree(buff); if (err_type == ERR_TYPE_KERNEL_PANIC_GZ) { big_buff = kmalloc(big_oops_buf_sz, GFP_KERNEL); if (!big_buff) return -ENOMEM; - rc = unzip_oops(buff, big_buff); + unzipped_len = nvram_decompress(*buf, big_buff, + length, big_oops_buf_sz); - if (rc != 0) { - kfree(buff); + if (unzipped_len < 0) { + pr_err("nvram: decompression failed, returned " + "rc %d\n", unzipped_len); kfree(big_buff); - goto read_partition; + } else { + *buf = big_buff; + length = unzipped_len; } - - oops_hdr = (struct oops_log_info *)big_buff; - *buf = big_buff + sizeof(*oops_hdr); - kfree(buff); } - - time->tv_sec = oops_hdr->timestamp; - time->tv_nsec = 0; - return oops_hdr->report_length; + return length; } *buf = buff; @@ -816,6 +792,7 @@ static int nvram_pstore_init(void) static void __init nvram_init_oops_partition(int rtas_partition_exists) { int rc; + size_t size; rc = pseries_nvram_init_os_partition(&oops_log_partition); if (rc != 0) { @@ -844,8 +821,9 @@ static void __init nvram_init_oops_partition(int rtas_partition_exists) big_oops_buf_sz = (oops_data_sz * 100) / 45; big_oops_buf = kmalloc(big_oops_buf_sz, GFP_KERNEL); if (big_oops_buf) { - stream.workspace = kmalloc(zlib_deflate_workspacesize( - WINDOW_BITS, MEM_LEVEL), GFP_KERNEL); + size = max(zlib_deflate_workspacesize(WINDOW_BITS, MEM_LEVEL), + zlib_inflate_workspacesize()); + stream.workspace = kmalloc(size, GFP_KERNEL); if (!stream.workspace) { pr_err("nvram: No memory for compression workspace; " "skipping compression of %s partition data\n", -- cgit v1.2.3-70-g09d2 From 156c9ebdaca20d9ce428dc189f2b24d2a0ec8eaf Mon Sep 17 00:00:00 2001 From: Aruna Balakrishnaiah Date: Thu, 8 Aug 2013 22:34:00 +0530 Subject: powerpc/pseries: Add backward compatibilty to read old kernel oops-log Older kernels has just length information in their header. Handle it while reading old kernel oops log from pstore. Applies on top of powerpc/pseries: Fix buffer overflow when reading from pstore Signed-off-by: Aruna Balakrishnaiah Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/nvram.c | 18 ++++++++++++++---- 1 file changed, 14 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/nvram.c b/arch/powerpc/platforms/pseries/nvram.c index 893f36053c9..6a5f2b1f32c 100644 --- a/arch/powerpc/platforms/pseries/nvram.c +++ b/arch/powerpc/platforms/pseries/nvram.c @@ -720,15 +720,25 @@ static ssize_t nvram_pstore_read(u64 *id, enum pstore_type_id *type, if (nvram_type_ids[read_type] == PSTORE_TYPE_DMESG) { int length, unzipped_len; + size_t hdr_size; oops_hdr = (struct oops_log_info *)buff; - length = oops_hdr->report_length; + if (oops_hdr->version < OOPS_HDR_VERSION) { + /* Old format oops header had 2-byte record size */ + hdr_size = sizeof(u16); + length = oops_hdr->version; + time->tv_sec = 0; + time->tv_nsec = 0; + } else { + hdr_size = sizeof(*oops_hdr); + length = oops_hdr->report_length; + time->tv_sec = oops_hdr->timestamp; + time->tv_nsec = 0; + } *buf = kmalloc(length, GFP_KERNEL); if (*buf == NULL) return -ENOMEM; - memcpy(*buf, buff + sizeof(*oops_hdr), length); - time->tv_sec = oops_hdr->timestamp; - time->tv_nsec = 0; + memcpy(*buf, buff + hdr_size, length); kfree(buff); if (err_type == ERR_TYPE_KERNEL_PANIC_GZ) { -- cgit v1.2.3-70-g09d2 From 144136dd7a25a0ca4d86685f872168502f91f337 Mon Sep 17 00:00:00 2001 From: Mike Qiu Date: Tue, 6 Aug 2013 22:25:14 -0400 Subject: powerpc/eeh: Add missing procfs entry for PowerNV The procfs entry for global statistics has been missed on PowerNV platform and the patch is going to add that. Signed-off-by: Mike Qiu Acked-by: Gavin Shan Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/eeh.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/eeh.c b/arch/powerpc/kernel/eeh.c index ea9414c8088..55593ee2d5a 100644 --- a/arch/powerpc/kernel/eeh.c +++ b/arch/powerpc/kernel/eeh.c @@ -1061,7 +1061,7 @@ static const struct file_operations proc_eeh_operations = { static int __init eeh_init_proc(void) { - if (machine_is(pseries)) + if (machine_is(pseries) || machine_is(powernv)) proc_create("powerpc/eeh", 0, NULL, &proc_eeh_operations); return 0; } -- cgit v1.2.3-70-g09d2 From 2fb10672c828f6e08f1dbe3690167300035adddc Mon Sep 17 00:00:00 2001 From: Chen Gang Date: Mon, 22 Jul 2013 14:32:35 +0800 Subject: powerpc/kvm: Add signed type cast for comparation 'rmls' is 'unsigned long', lpcr_rmls() will return negative number when failure occurs, so it need a type cast for comparing. 'lpid' is 'unsigned long', kvmppc_alloc_lpid() return negative number when failure occurs, so it need a type cast for comparing. Signed-off-by: Chen Gang Acked-by: Paul Mackerras Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kvm/book3s_hv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c index 2efa9dde741..7629cd3eb91 100644 --- a/arch/powerpc/kvm/book3s_hv.c +++ b/arch/powerpc/kvm/book3s_hv.c @@ -1809,7 +1809,7 @@ static int kvmppc_hv_setup_htab_rma(struct kvm_vcpu *vcpu) rma_size <<= PAGE_SHIFT; rmls = lpcr_rmls(rma_size); err = -EINVAL; - if (rmls < 0) { + if ((long)rmls < 0) { pr_err("KVM: Can't use RMA of 0x%lx bytes\n", rma_size); goto out_srcu; } @@ -1874,7 +1874,7 @@ int kvmppc_core_init_vm(struct kvm *kvm) /* Allocate the guest's logical partition ID */ lpid = kvmppc_alloc_lpid(); - if (lpid < 0) + if ((long)lpid < 0) return -ENOMEM; kvm->arch.lpid = lpid; -- cgit v1.2.3-70-g09d2 From e0e13614626bfb5a88678fd951d728ed40e3cbf6 Mon Sep 17 00:00:00 2001 From: Thadeu Lima de Souza Cascardo Date: Wed, 17 Jul 2013 12:10:29 -0300 Subject: powerpc/kvm/book3s_pr: Return appropriate error when allocation fails err was overwritten by a previous function call, and checked to be 0. If the following page allocation fails, 0 is going to be returned instead of -ENOMEM. Signed-off-by: Thadeu Lima de Souza Cascardo Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kvm/book3s_pr.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kvm/book3s_pr.c b/arch/powerpc/kvm/book3s_pr.c index 19498a567a8..c6e13d9a9e1 100644 --- a/arch/powerpc/kvm/book3s_pr.c +++ b/arch/powerpc/kvm/book3s_pr.c @@ -1047,11 +1047,12 @@ struct kvm_vcpu *kvmppc_core_vcpu_create(struct kvm *kvm, unsigned int id) if (err) goto free_shadow_vcpu; + err = -ENOMEM; p = __get_free_page(GFP_KERNEL|__GFP_ZERO); - /* the real shared page fills the last 4k of our page */ - vcpu->arch.shared = (void*)(p + PAGE_SIZE - 4096); if (!p) goto uninit_vcpu; + /* the real shared page fills the last 4k of our page */ + vcpu->arch.shared = (void *)(p + PAGE_SIZE - 4096); #ifdef CONFIG_PPC_BOOK3S_64 /* default to book3s_64 (970fx) */ -- cgit v1.2.3-70-g09d2 From 88f094120bd2f012ff494ae50a8d4e0d8af8f69e Mon Sep 17 00:00:00 2001 From: Michael Neuling Date: Fri, 9 Aug 2013 17:29:27 +1000 Subject: powerpc: Fix hypervisor facility unavaliable vector number Currently if we take hypervisor facility unavaliable (from 0xf80/0x4f80) we mark it as an OS facility unavaliable (0xf60) as the two share the same code path. The becomes a problem in facility_unavailable_exception() as we aren't able to see the hypervisor facility unavailable exceptions. Below fixes this by duplication the required macros. Signed-off-by: Michael Neuling Cc: [v3.10] Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/exceptions-64s.S | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/exceptions-64s.S b/arch/powerpc/kernel/exceptions-64s.S index 4e00d223b2e..902ca3c6b4b 100644 --- a/arch/powerpc/kernel/exceptions-64s.S +++ b/arch/powerpc/kernel/exceptions-64s.S @@ -848,7 +848,7 @@ hv_facility_unavailable_relon_trampoline: . = 0x4f80 SET_SCRATCH0(r13) EXCEPTION_PROLOG_0(PACA_EXGEN) - b facility_unavailable_relon_hv + b hv_facility_unavailable_relon_hv STD_RELON_EXCEPTION_PSERIES(0x5300, 0x1300, instruction_breakpoint) #ifdef CONFIG_PPC_DENORMALISATION @@ -1175,6 +1175,7 @@ END_FTR_SECTION_IFSET(CPU_FTR_VSX) b .ret_from_except STD_EXCEPTION_COMMON(0xf60, facility_unavailable, .facility_unavailable_exception) + STD_EXCEPTION_COMMON(0xf80, hv_facility_unavailable, .facility_unavailable_exception) .align 7 .globl __end_handlers @@ -1188,7 +1189,7 @@ __end_handlers: STD_RELON_EXCEPTION_PSERIES_OOL(0xf20, altivec_unavailable) STD_RELON_EXCEPTION_PSERIES_OOL(0xf40, vsx_unavailable) STD_RELON_EXCEPTION_PSERIES_OOL(0xf60, facility_unavailable) - STD_RELON_EXCEPTION_HV_OOL(0xf80, facility_unavailable) + STD_RELON_EXCEPTION_HV_OOL(0xf80, hv_facility_unavailable) #if defined(CONFIG_PPC_PSERIES) || defined(CONFIG_PPC_POWERNV) /* -- cgit v1.2.3-70-g09d2 From 74e400cee6c0266ba2d940ed78d981f1e24a8167 Mon Sep 17 00:00:00 2001 From: Michael Neuling Date: Fri, 9 Aug 2013 17:29:28 +1000 Subject: powerpc: Rework setting up H/FSCR bit definitions This reworks the Facility Status and Control Regsiter (FSCR) config bit definitions so that we can access the bit numbers. This is needed for a subsequent patch to fix the userspace DSCR handling. HFSCR and FSCR bit definitions are the same, so reuse them. Signed-off-by: Michael Neuling Cc: [v3.10] Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/reg.h | 31 ++++++++++++++++++++----------- 1 file changed, 20 insertions(+), 11 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/reg.h b/arch/powerpc/include/asm/reg.h index a6840e4e24f..99222e27f17 100644 --- a/arch/powerpc/include/asm/reg.h +++ b/arch/powerpc/include/asm/reg.h @@ -254,19 +254,28 @@ #define SPRN_HRMOR 0x139 /* Real mode offset register */ #define SPRN_HSRR0 0x13A /* Hypervisor Save/Restore 0 */ #define SPRN_HSRR1 0x13B /* Hypervisor Save/Restore 1 */ +/* HFSCR and FSCR bit numbers are the same */ +#define FSCR_TAR_LG 8 /* Enable Target Address Register */ +#define FSCR_EBB_LG 7 /* Enable Event Based Branching */ +#define FSCR_TM_LG 5 /* Enable Transactional Memory */ +#define FSCR_PM_LG 4 /* Enable prob/priv access to PMU SPRs */ +#define FSCR_BHRB_LG 3 /* Enable Branch History Rolling Buffer*/ +#define FSCR_DSCR_LG 2 /* Enable Data Stream Control Register */ +#define FSCR_VECVSX_LG 1 /* Enable VMX/VSX */ +#define FSCR_FP_LG 0 /* Enable Floating Point */ #define SPRN_FSCR 0x099 /* Facility Status & Control Register */ -#define FSCR_TAR (1 << (63-55)) /* Enable Target Address Register */ -#define FSCR_EBB (1 << (63-56)) /* Enable Event Based Branching */ -#define FSCR_DSCR (1 << (63-61)) /* Enable Data Stream Control Register */ +#define FSCR_TAR __MASK(FSCR_TAR_LG) +#define FSCR_EBB __MASK(FSCR_EBB_LG) +#define FSCR_DSCR __MASK(FSCR_DSCR_LG) #define SPRN_HFSCR 0xbe /* HV=1 Facility Status & Control Register */ -#define HFSCR_TAR (1 << (63-55)) /* Enable Target Address Register */ -#define HFSCR_EBB (1 << (63-56)) /* Enable Event Based Branching */ -#define HFSCR_TM (1 << (63-58)) /* Enable Transactional Memory */ -#define HFSCR_PM (1 << (63-60)) /* Enable prob/priv access to PMU SPRs */ -#define HFSCR_BHRB (1 << (63-59)) /* Enable Branch History Rolling Buffer*/ -#define HFSCR_DSCR (1 << (63-61)) /* Enable Data Stream Control Register */ -#define HFSCR_VECVSX (1 << (63-62)) /* Enable VMX/VSX */ -#define HFSCR_FP (1 << (63-63)) /* Enable Floating Point */ +#define HFSCR_TAR __MASK(FSCR_TAR_LG) +#define HFSCR_EBB __MASK(FSCR_EBB_LG) +#define HFSCR_TM __MASK(FSCR_TM_LG) +#define HFSCR_PM __MASK(FSCR_PM_LG) +#define HFSCR_BHRB __MASK(FSCR_BHRB_LG) +#define HFSCR_DSCR __MASK(FSCR_DSCR_LG) +#define HFSCR_VECVSX __MASK(FSCR_VECVSX_LG) +#define HFSCR_FP __MASK(FSCR_FP_LG) #define SPRN_TAR 0x32f /* Target Address Register */ #define SPRN_LPCR 0x13E /* LPAR Control Register */ #define LPCR_VPM0 (1ul << (63-0)) -- cgit v1.2.3-70-g09d2 From 2517617e0de65f8f7cfe75cae745d06b1fa98586 Mon Sep 17 00:00:00 2001 From: Michael Neuling Date: Fri, 9 Aug 2013 17:29:29 +1000 Subject: powerpc: Fix context switch DSCR on POWER8 POWER8 allows the DSCR to be accessed directly from userspace via a new SPR number 0x3 (Rather than 0x11. DSCR SPR number 0x11 is still used on POWER8 but like POWER7, is only accessible in HV and OS modes). Currently, we allow this by setting H/FSCR DSCR bit on boot. Unfortunately this doesn't work, as the kernel needs to see the DSCR change so that it knows to no longer restore the system wide version of DSCR on context switch (ie. to set thread.dscr_inherit). This clears the H/FSCR DSCR bit initially. If a process then accesses the DSCR (via SPR 0x3), it'll trap into the kernel where we set thread.dscr_inherit in facility_unavailable_exception(). We also change _switch() so that we set or clear the H/FSCR DSCR bit based on the thread.dscr_inherit. Signed-off-by: Michael Neuling Cc: [v3.10] Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/entry_64.S | 27 +++++++++++++++++++- arch/powerpc/kernel/traps.c | 58 +++++++++++++++++++++++++----------------- 2 files changed, 60 insertions(+), 25 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index ab15b8d057a..4674fe647ad 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -584,9 +584,34 @@ BEGIN_FTR_SECTION ld r7,DSCR_DEFAULT@toc(2) ld r0,THREAD_DSCR(r4) cmpwi r6,0 + li r8, FSCR_DSCR bne 1f ld r0,0(r7) -1: cmpd r0,r25 + b 3f +1: + BEGIN_FTR_SECTION_NESTED(70) + mfspr r6, SPRN_FSCR + or r6, r6, r8 + mtspr SPRN_FSCR, r6 + BEGIN_FTR_SECTION_NESTED(69) + mfspr r6, SPRN_HFSCR + or r6, r6, r8 + mtspr SPRN_HFSCR, r6 + END_FTR_SECTION_NESTED(CPU_FTR_HVMODE, CPU_FTR_HVMODE, 69) + b 4f + END_FTR_SECTION_NESTED(CPU_FTR_ARCH_207S, CPU_FTR_ARCH_207S, 70) +3: + BEGIN_FTR_SECTION_NESTED(70) + mfspr r6, SPRN_FSCR + andc r6, r6, r8 + mtspr SPRN_FSCR, r6 + BEGIN_FTR_SECTION_NESTED(69) + mfspr r6, SPRN_HFSCR + andc r6, r6, r8 + mtspr SPRN_HFSCR, r6 + END_FTR_SECTION_NESTED(CPU_FTR_HVMODE, CPU_FTR_HVMODE, 69) + END_FTR_SECTION_NESTED(CPU_FTR_ARCH_207S, CPU_FTR_ARCH_207S, 70) +4: cmpd r0,r25 beq 2f mtspr SPRN_DSCR,r0 2: diff --git a/arch/powerpc/kernel/traps.c b/arch/powerpc/kernel/traps.c index bf33c22e38a..e435bc089ea 100644 --- a/arch/powerpc/kernel/traps.c +++ b/arch/powerpc/kernel/traps.c @@ -44,9 +44,7 @@ #include #include #include -#ifdef CONFIG_PPC32 #include -#endif #ifdef CONFIG_PMAC_BACKLIGHT #include #endif @@ -1296,43 +1294,54 @@ void vsx_unavailable_exception(struct pt_regs *regs) die("Unrecoverable VSX Unavailable Exception", regs, SIGABRT); } +#ifdef CONFIG_PPC64 void facility_unavailable_exception(struct pt_regs *regs) { static char *facility_strings[] = { - "FPU", - "VMX/VSX", - "DSCR", - "PMU SPRs", - "BHRB", - "TM", - "AT", - "EBB", - "TAR", + [FSCR_FP_LG] = "FPU", + [FSCR_VECVSX_LG] = "VMX/VSX", + [FSCR_DSCR_LG] = "DSCR", + [FSCR_PM_LG] = "PMU SPRs", + [FSCR_BHRB_LG] = "BHRB", + [FSCR_TM_LG] = "TM", + [FSCR_EBB_LG] = "EBB", + [FSCR_TAR_LG] = "TAR", }; - char *facility, *prefix; + char *facility = "unknown"; u64 value; + u8 status; + bool hv; - if (regs->trap == 0xf60) { - value = mfspr(SPRN_FSCR); - prefix = ""; - } else { + hv = (regs->trap == 0xf80); + if (hv) value = mfspr(SPRN_HFSCR); - prefix = "Hypervisor "; + else + value = mfspr(SPRN_FSCR); + + status = value >> 56; + if (status == FSCR_DSCR_LG) { + /* User is acessing the DSCR. Set the inherit bit and allow + * the user to set it directly in future by setting via the + * H/FSCR DSCR bit. + */ + current->thread.dscr_inherit = 1; + if (hv) + mtspr(SPRN_HFSCR, value | HFSCR_DSCR); + else + mtspr(SPRN_FSCR, value | FSCR_DSCR); + return; } - value = value >> 56; + if ((status < ARRAY_SIZE(facility_strings)) && + facility_strings[status]) + facility = facility_strings[status]; /* We restore the interrupt state now */ if (!arch_irq_disabled_regs(regs)) local_irq_enable(); - if (value < ARRAY_SIZE(facility_strings)) - facility = facility_strings[value]; - else - facility = "unknown"; - pr_err("%sFacility '%s' unavailable, exception at 0x%lx, MSR=%lx\n", - prefix, facility, regs->nip, regs->msr); + hv ? "Hypervisor " : "", facility, regs->nip, regs->msr); if (user_mode(regs)) { _exception(SIGILL, regs, ILL_ILLOPC, regs->nip); @@ -1341,6 +1350,7 @@ void facility_unavailable_exception(struct pt_regs *regs) die("Unexpected facility unavailable exception", regs, SIGABRT); } +#endif #ifdef CONFIG_PPC_TRANSACTIONAL_MEM -- cgit v1.2.3-70-g09d2 From c2d52644e2da8a07ecab5ca62dd0bc563089e8dc Mon Sep 17 00:00:00 2001 From: Michael Neuling Date: Fri, 9 Aug 2013 17:29:30 +1000 Subject: powerpc: Save the TAR register earlier This moves us to save the Target Address Register (TAR) a earlier in __switch_to. It introduces a new function save_tar() to do this. We need to save the TAR earlier as we will overwrite it in the transactional memory reclaim/recheckpoint path. We are going to do this in a subsequent patch which will fix saving the TAR register when it's modified inside a transaction. Signed-off-by: Michael Neuling Cc: [v3.10] Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/switch_to.h | 9 +++++++++ arch/powerpc/kernel/entry_64.S | 9 --------- arch/powerpc/kernel/process.c | 10 ++++++++++ 3 files changed, 19 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/switch_to.h b/arch/powerpc/include/asm/switch_to.h index 49a13e0ef23..294c2cedcf7 100644 --- a/arch/powerpc/include/asm/switch_to.h +++ b/arch/powerpc/include/asm/switch_to.h @@ -15,6 +15,15 @@ extern struct task_struct *__switch_to(struct task_struct *, struct thread_struct; extern struct task_struct *_switch(struct thread_struct *prev, struct thread_struct *next); +#ifdef CONFIG_PPC_BOOK3S_64 +static inline void save_tar(struct thread_struct *prev) +{ + if (cpu_has_feature(CPU_FTR_ARCH_207S)) + prev->tar = mfspr(SPRN_TAR); +} +#else +static inline void save_tar(struct thread_struct *prev) {} +#endif extern void giveup_fpu(struct task_struct *); extern void load_up_fpu(void); diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index 4674fe647ad..2bd0b885b0f 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -449,15 +449,6 @@ END_FTR_SECTION_IFSET(CPU_FTR_DSCR) #ifdef CONFIG_PPC_BOOK3S_64 BEGIN_FTR_SECTION - /* - * Back up the TAR across context switches. Note that the TAR is not - * available for use in the kernel. (To provide this, the TAR should - * be backed up/restored on exception entry/exit instead, and be in - * pt_regs. FIXME, this should be in pt_regs anyway (for debug).) - */ - mfspr r0,SPRN_TAR - std r0,THREAD_TAR(r3) - /* Event based branch registers */ mfspr r0, SPRN_BESCR std r0, THREAD_BESCR(r3) diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c index c517dbe705f..8083be20fe5 100644 --- a/arch/powerpc/kernel/process.c +++ b/arch/powerpc/kernel/process.c @@ -600,6 +600,16 @@ struct task_struct *__switch_to(struct task_struct *prev, struct ppc64_tlb_batch *batch; #endif + /* Back up the TAR across context switches. + * Note that the TAR is not available for use in the kernel. (To + * provide this, the TAR should be backed up/restored on exception + * entry/exit instead, and be in pt_regs. FIXME, this should be in + * pt_regs anyway (for debug).) + * Save the TAR here before we do treclaim/trecheckpoint as these + * will change the TAR. + */ + save_tar(&prev->thread); + __switch_to_tm(prev); #ifdef CONFIG_SMP -- cgit v1.2.3-70-g09d2 From 28e61cc466d8daace4b0f04ba2b83e0bd68f5832 Mon Sep 17 00:00:00 2001 From: Michael Neuling Date: Fri, 9 Aug 2013 17:29:31 +1000 Subject: powerpc/tm: Fix context switching TAR, PPR and DSCR SPRs If a transaction is rolled back, the Target Address Register (TAR), Processor Priority Register (PPR) and Data Stream Control Register (DSCR) should be restored to the checkpointed values before the transaction began. Any changes to these SPRs inside the transaction should not be visible in the abort handler. Currently Linux doesn't save or restore the checkpointed TAR, PPR or DSCR. If we preempt a processes inside a transaction which has modified any of these, on process restore, that same transaction may be aborted we but we won't see the checkpointed versions of these SPRs. This adds checkpointed versions of these SPRs to the thread_struct and adds the save/restore of these three SPRs to the treclaim/trechkpt code. Without this if any of these SPRs are modified during a transaction, users may incorrectly see a speculated SPR value even if the transaction is aborted. Signed-off-by: Michael Neuling Cc: [v3.10] Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/processor.h | 4 ++++ arch/powerpc/kernel/asm-offsets.c | 3 +++ arch/powerpc/kernel/tm.S | 20 ++++++++++++++++++++ 3 files changed, 27 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h index 47a35b08b96..e378cccfca5 100644 --- a/arch/powerpc/include/asm/processor.h +++ b/arch/powerpc/include/asm/processor.h @@ -247,6 +247,10 @@ struct thread_struct { unsigned long tm_orig_msr; /* Thread's MSR on ctx switch */ struct pt_regs ckpt_regs; /* Checkpointed registers */ + unsigned long tm_tar; + unsigned long tm_ppr; + unsigned long tm_dscr; + /* * Transactional FP and VSX 0-31 register set. * NOTE: the sense of these is the opposite of the integer ckpt_regs! diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c index c7e8afc2ead..8207459efe5 100644 --- a/arch/powerpc/kernel/asm-offsets.c +++ b/arch/powerpc/kernel/asm-offsets.c @@ -138,6 +138,9 @@ int main(void) DEFINE(THREAD_TM_TFHAR, offsetof(struct thread_struct, tm_tfhar)); DEFINE(THREAD_TM_TEXASR, offsetof(struct thread_struct, tm_texasr)); DEFINE(THREAD_TM_TFIAR, offsetof(struct thread_struct, tm_tfiar)); + DEFINE(THREAD_TM_TAR, offsetof(struct thread_struct, tm_tar)); + DEFINE(THREAD_TM_PPR, offsetof(struct thread_struct, tm_ppr)); + DEFINE(THREAD_TM_DSCR, offsetof(struct thread_struct, tm_dscr)); DEFINE(PT_CKPT_REGS, offsetof(struct thread_struct, ckpt_regs)); DEFINE(THREAD_TRANSACT_VR0, offsetof(struct thread_struct, transact_vr[0])); diff --git a/arch/powerpc/kernel/tm.S b/arch/powerpc/kernel/tm.S index 51be8fb2480..0554d1f6d70 100644 --- a/arch/powerpc/kernel/tm.S +++ b/arch/powerpc/kernel/tm.S @@ -233,6 +233,16 @@ dont_backup_fp: std r5, _CCR(r7) std r6, _XER(r7) + + /* ******************** TAR, PPR, DSCR ********** */ + mfspr r3, SPRN_TAR + mfspr r4, SPRN_PPR + mfspr r5, SPRN_DSCR + + std r3, THREAD_TM_TAR(r12) + std r4, THREAD_TM_PPR(r12) + std r5, THREAD_TM_DSCR(r12) + /* MSR and flags: We don't change CRs, and we don't need to alter * MSR. */ @@ -347,6 +357,16 @@ dont_restore_fp: mtmsr r6 /* FP/Vec off again! */ restore_gprs: + + /* ******************** TAR, PPR, DSCR ********** */ + ld r4, THREAD_TM_TAR(r3) + ld r5, THREAD_TM_PPR(r3) + ld r6, THREAD_TM_DSCR(r3) + + mtspr SPRN_TAR, r4 + mtspr SPRN_PPR, r5 + mtspr SPRN_DSCR, r6 + /* ******************** CR,LR,CCR,MSR ********** */ ld r3, _CTR(r7) ld r4, _LINK(r7) -- cgit v1.2.3-70-g09d2