From 1745522ccbabd990bfc7511861aa9fa98287cba0 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Mon, 26 Jan 2009 21:19:52 +0100 Subject: i2c: Delete many unused adapter IDs Signed-off-by: Jean Delvare --- drivers/i2c/busses/i2c-acorn.c | 1 - drivers/i2c/busses/i2c-ali1535.c | 1 - drivers/i2c/busses/i2c-ali1563.c | 1 - drivers/i2c/busses/i2c-ali15x3.c | 1 - drivers/i2c/busses/i2c-amd756.c | 1 - drivers/i2c/busses/i2c-amd8111.c | 1 - drivers/i2c/busses/i2c-au1550.c | 1 - drivers/i2c/busses/i2c-bfin-twi.c | 1 - drivers/i2c/busses/i2c-elektor.c | 1 - drivers/i2c/busses/i2c-hydra.c | 1 - drivers/i2c/busses/i2c-i801.c | 1 - drivers/i2c/busses/i2c-ibm_iic.c | 1 - drivers/i2c/busses/i2c-iop3xx.c | 1 - drivers/i2c/busses/i2c-ixp2000.c | 1 - drivers/i2c/busses/i2c-mpc.c | 1 - drivers/i2c/busses/i2c-mv64xxx.c | 1 - drivers/i2c/busses/i2c-nforce2.c | 1 - drivers/i2c/busses/i2c-parport-light.c | 1 - drivers/i2c/busses/i2c-parport.c | 1 - drivers/i2c/busses/i2c-pca-isa.c | 1 - drivers/i2c/busses/i2c-piix4.c | 1 - drivers/i2c/busses/i2c-sibyte.c | 2 -- drivers/i2c/busses/i2c-sis5595.c | 1 - drivers/i2c/busses/i2c-sis630.c | 1 - drivers/i2c/busses/i2c-sis96x.c | 1 - drivers/i2c/busses/i2c-via.c | 1 - drivers/i2c/busses/i2c-viapro.c | 1 - drivers/i2c/busses/i2c-voodoo3.c | 2 -- drivers/i2c/busses/scx200_acb.c | 1 - drivers/i2c/busses/scx200_i2c.c | 1 - 30 files changed, 32 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-acorn.c b/drivers/i2c/busses/i2c-acorn.c index 75089febbc1..9fee3ca1734 100644 --- a/drivers/i2c/busses/i2c-acorn.c +++ b/drivers/i2c/busses/i2c-acorn.c @@ -83,7 +83,6 @@ static struct i2c_algo_bit_data ioc_data = { }; static struct i2c_adapter ioc_ops = { - .id = I2C_HW_B_IOC, .algo_data = &ioc_data, }; diff --git a/drivers/i2c/busses/i2c-ali1535.c b/drivers/i2c/busses/i2c-ali1535.c index 9cead9b9458..981e080b32a 100644 --- a/drivers/i2c/busses/i2c-ali1535.c +++ b/drivers/i2c/busses/i2c-ali1535.c @@ -476,7 +476,6 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter ali1535_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_ALI1535, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-ali1563.c b/drivers/i2c/busses/i2c-ali1563.c index dd9e796fad6..f70f46582c6 100644 --- a/drivers/i2c/busses/i2c-ali1563.c +++ b/drivers/i2c/busses/i2c-ali1563.c @@ -386,7 +386,6 @@ static const struct i2c_algorithm ali1563_algorithm = { static struct i2c_adapter ali1563_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_ALI1563, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &ali1563_algorithm, }; diff --git a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c index 234fdde7d40..39066dee46e 100644 --- a/drivers/i2c/busses/i2c-ali15x3.c +++ b/drivers/i2c/busses/i2c-ali15x3.c @@ -473,7 +473,6 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter ali15x3_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_ALI15X3, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-amd756.c b/drivers/i2c/busses/i2c-amd756.c index 36bee5b9c95..220f4a1eee1 100644 --- a/drivers/i2c/busses/i2c-amd756.c +++ b/drivers/i2c/busses/i2c-amd756.c @@ -298,7 +298,6 @@ static const struct i2c_algorithm smbus_algorithm = { struct i2c_adapter amd756_smbus = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_AMD756, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-amd8111.c b/drivers/i2c/busses/i2c-amd8111.c index 3972208876b..edab51973bf 100644 --- a/drivers/i2c/busses/i2c-amd8111.c +++ b/drivers/i2c/busses/i2c-amd8111.c @@ -387,7 +387,6 @@ static int __devinit amd8111_probe(struct pci_dev *dev, smbus->adapter.owner = THIS_MODULE; snprintf(smbus->adapter.name, sizeof(smbus->adapter.name), "SMBus2 AMD8111 adapter at %04x", smbus->base); - smbus->adapter.id = I2C_HW_SMBUS_AMD8111; smbus->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD; smbus->adapter.algo = &smbus_algorithm; smbus->adapter.algo_data = smbus; diff --git a/drivers/i2c/busses/i2c-au1550.c b/drivers/i2c/busses/i2c-au1550.c index 66a04c2c660..f78ce523e3d 100644 --- a/drivers/i2c/busses/i2c-au1550.c +++ b/drivers/i2c/busses/i2c-au1550.c @@ -400,7 +400,6 @@ i2c_au1550_probe(struct platform_device *pdev) priv->xfer_timeout = 200; priv->ack_timeout = 200; - priv->adap.id = I2C_HW_AU1550_PSC; priv->adap.nr = pdev->id; priv->adap.algo = &au1550_algo; priv->adap.algo_data = priv; diff --git a/drivers/i2c/busses/i2c-bfin-twi.c b/drivers/i2c/busses/i2c-bfin-twi.c index 3fd2c417c1e..fc548b3d002 100644 --- a/drivers/i2c/busses/i2c-bfin-twi.c +++ b/drivers/i2c/busses/i2c-bfin-twi.c @@ -651,7 +651,6 @@ static int i2c_bfin_twi_probe(struct platform_device *pdev) iface->timeout_timer.data = (unsigned long)iface; p_adap = &iface->adap; - p_adap->id = I2C_HW_BLACKFIN; p_adap->nr = pdev->id; strlcpy(p_adap->name, pdev->name, sizeof(p_adap->name)); p_adap->algo = &bfin_twi_algorithm; diff --git a/drivers/i2c/busses/i2c-elektor.c b/drivers/i2c/busses/i2c-elektor.c index 0ed3ccb81b6..448b4bf35eb 100644 --- a/drivers/i2c/busses/i2c-elektor.c +++ b/drivers/i2c/busses/i2c-elektor.c @@ -202,7 +202,6 @@ static struct i2c_algo_pcf_data pcf_isa_data = { static struct i2c_adapter pcf_isa_ops = { .owner = THIS_MODULE, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, - .id = I2C_HW_P_ELEK, .algo_data = &pcf_isa_data, .name = "i2c-elektor", }; diff --git a/drivers/i2c/busses/i2c-hydra.c b/drivers/i2c/busses/i2c-hydra.c index 648aa7baff8..bec9b845dd1 100644 --- a/drivers/i2c/busses/i2c-hydra.c +++ b/drivers/i2c/busses/i2c-hydra.c @@ -102,7 +102,6 @@ static struct i2c_algo_bit_data hydra_bit_data = { static struct i2c_adapter hydra_adap = { .owner = THIS_MODULE, .name = "Hydra i2c", - .id = I2C_HW_B_HYDRA, .algo_data = &hydra_bit_data, }; diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index 526625eaa84..230238df56c 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -556,7 +556,6 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter i801_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_I801, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-ibm_iic.c b/drivers/i2c/busses/i2c-ibm_iic.c index 651f2f1ae5b..88f0db73b36 100644 --- a/drivers/i2c/busses/i2c-ibm_iic.c +++ b/drivers/i2c/busses/i2c-ibm_iic.c @@ -746,7 +746,6 @@ static int __devinit iic_probe(struct of_device *ofdev, adap->dev.parent = &ofdev->dev; strlcpy(adap->name, "IBM IIC", sizeof(adap->name)); i2c_set_adapdata(adap, dev); - adap->id = I2C_HW_OCP; adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; adap->algo = &iic_algo; adap->timeout = 1; diff --git a/drivers/i2c/busses/i2c-iop3xx.c b/drivers/i2c/busses/i2c-iop3xx.c index fc2714ac0c0..3190690c26c 100644 --- a/drivers/i2c/busses/i2c-iop3xx.c +++ b/drivers/i2c/busses/i2c-iop3xx.c @@ -480,7 +480,6 @@ iop3xx_i2c_probe(struct platform_device *pdev) } memcpy(new_adapter->name, pdev->name, strlen(pdev->name)); - new_adapter->id = I2C_HW_IOP3XX; new_adapter->owner = THIS_MODULE; new_adapter->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; new_adapter->dev.parent = &pdev->dev; diff --git a/drivers/i2c/busses/i2c-ixp2000.c b/drivers/i2c/busses/i2c-ixp2000.c index 05d72e98135..8e846797048 100644 --- a/drivers/i2c/busses/i2c-ixp2000.c +++ b/drivers/i2c/busses/i2c-ixp2000.c @@ -116,7 +116,6 @@ static int ixp2000_i2c_probe(struct platform_device *plat_dev) drv_data->algo_data.udelay = 6; drv_data->algo_data.timeout = 100; - drv_data->adapter.id = I2C_HW_B_IXP2000, strlcpy(drv_data->adapter.name, plat_dev->dev.driver->name, sizeof(drv_data->adapter.name)); drv_data->adapter.algo_data = &drv_data->algo_data, diff --git a/drivers/i2c/busses/i2c-mpc.c b/drivers/i2c/busses/i2c-mpc.c index a9a45fcc854..aedbbe6618d 100644 --- a/drivers/i2c/busses/i2c-mpc.c +++ b/drivers/i2c/busses/i2c-mpc.c @@ -310,7 +310,6 @@ static const struct i2c_algorithm mpc_algo = { static struct i2c_adapter mpc_ops = { .owner = THIS_MODULE, .name = "MPC adapter", - .id = I2C_HW_MPC107, .algo = &mpc_algo, .timeout = 1, }; diff --git a/drivers/i2c/busses/i2c-mv64xxx.c b/drivers/i2c/busses/i2c-mv64xxx.c index 9e8118d2fe6..eeda276f8f1 100644 --- a/drivers/i2c/busses/i2c-mv64xxx.c +++ b/drivers/i2c/busses/i2c-mv64xxx.c @@ -527,7 +527,6 @@ mv64xxx_i2c_probe(struct platform_device *pd) goto exit_unmap_regs; } drv_data->adapter.dev.parent = &pd->dev; - drv_data->adapter.id = I2C_HW_MV64XXX; drv_data->adapter.algo = &mv64xxx_i2c_algo; drv_data->adapter.owner = THIS_MODULE; drv_data->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD; diff --git a/drivers/i2c/busses/i2c-nforce2.c b/drivers/i2c/busses/i2c-nforce2.c index 3b19bc41a60..05af6cd7f27 100644 --- a/drivers/i2c/busses/i2c-nforce2.c +++ b/drivers/i2c/busses/i2c-nforce2.c @@ -355,7 +355,6 @@ static int __devinit nforce2_probe_smb (struct pci_dev *dev, int bar, return -EBUSY; } smbus->adapter.owner = THIS_MODULE; - smbus->adapter.id = I2C_HW_SMBUS_NFORCE2; smbus->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD; smbus->adapter.algo = &smbus_algorithm; smbus->adapter.algo_data = smbus; diff --git a/drivers/i2c/busses/i2c-parport-light.c b/drivers/i2c/busses/i2c-parport-light.c index b2b8380f660..322c5691e38 100644 --- a/drivers/i2c/busses/i2c-parport-light.c +++ b/drivers/i2c/busses/i2c-parport-light.c @@ -115,7 +115,6 @@ static struct i2c_algo_bit_data parport_algo_data = { static struct i2c_adapter parport_adapter = { .owner = THIS_MODULE, .class = I2C_CLASS_HWMON, - .id = I2C_HW_B_LP, .algo_data = &parport_algo_data, .name = "Parallel port adapter (light)", }; diff --git a/drivers/i2c/busses/i2c-parport.c b/drivers/i2c/busses/i2c-parport.c index a257cd5cd13..0d8998610c7 100644 --- a/drivers/i2c/busses/i2c-parport.c +++ b/drivers/i2c/busses/i2c-parport.c @@ -164,7 +164,6 @@ static void i2c_parport_attach (struct parport *port) /* Fill the rest of the structure */ adapter->adapter.owner = THIS_MODULE; adapter->adapter.class = I2C_CLASS_HWMON; - adapter->adapter.id = I2C_HW_B_LP; strlcpy(adapter->adapter.name, "Parallel port adapter", sizeof(adapter->adapter.name)); adapter->algo_data = parport_algo_data; diff --git a/drivers/i2c/busses/i2c-pca-isa.c b/drivers/i2c/busses/i2c-pca-isa.c index 9eb76268ec7..4aa8138cb0a 100644 --- a/drivers/i2c/busses/i2c-pca-isa.c +++ b/drivers/i2c/busses/i2c-pca-isa.c @@ -101,7 +101,6 @@ static struct i2c_algo_pca_data pca_isa_data = { static struct i2c_adapter pca_isa_ops = { .owner = THIS_MODULE, - .id = I2C_HW_A_ISA, .algo_data = &pca_isa_data, .name = "PCA9564 ISA Adapter", .timeout = 100, diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c index eaa9b387543..761f9dd5362 100644 --- a/drivers/i2c/busses/i2c-piix4.c +++ b/drivers/i2c/busses/i2c-piix4.c @@ -403,7 +403,6 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter piix4_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_PIIX4, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-sibyte.c b/drivers/i2c/busses/i2c-sibyte.c index 4ddefbf238e..98b1ec48915 100644 --- a/drivers/i2c/busses/i2c-sibyte.c +++ b/drivers/i2c/busses/i2c-sibyte.c @@ -155,7 +155,6 @@ static struct i2c_algo_sibyte_data sibyte_board_data[2] = { static struct i2c_adapter sibyte_board_adapter[2] = { { .owner = THIS_MODULE, - .id = I2C_HW_SIBYTE, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = NULL, .algo_data = &sibyte_board_data[0], @@ -164,7 +163,6 @@ static struct i2c_adapter sibyte_board_adapter[2] = { }, { .owner = THIS_MODULE, - .id = I2C_HW_SIBYTE, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = NULL, .algo_data = &sibyte_board_data[1], diff --git a/drivers/i2c/busses/i2c-sis5595.c b/drivers/i2c/busses/i2c-sis5595.c index 8ce2daff985..f320ab27da4 100644 --- a/drivers/i2c/busses/i2c-sis5595.c +++ b/drivers/i2c/busses/i2c-sis5595.c @@ -365,7 +365,6 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter sis5595_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_SIS5595, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-sis630.c b/drivers/i2c/busses/i2c-sis630.c index 9c9c016ff2b..50c3610e602 100644 --- a/drivers/i2c/busses/i2c-sis630.c +++ b/drivers/i2c/busses/i2c-sis630.c @@ -464,7 +464,6 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter sis630_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_SIS630, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-sis96x.c b/drivers/i2c/busses/i2c-sis96x.c index f1bba639664..7e1594b4057 100644 --- a/drivers/i2c/busses/i2c-sis96x.c +++ b/drivers/i2c/busses/i2c-sis96x.c @@ -241,7 +241,6 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter sis96x_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_SIS96X, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-via.c b/drivers/i2c/busses/i2c-via.c index 29cef0433f3..8b24f192103 100644 --- a/drivers/i2c/busses/i2c-via.c +++ b/drivers/i2c/busses/i2c-via.c @@ -83,7 +83,6 @@ static struct i2c_algo_bit_data bit_data = { static struct i2c_adapter vt586b_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_B_VIA, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .name = "VIA i2c", .algo_data = &bit_data, diff --git a/drivers/i2c/busses/i2c-viapro.c b/drivers/i2c/busses/i2c-viapro.c index 9f194d9efd9..02e6f724b05 100644 --- a/drivers/i2c/busses/i2c-viapro.c +++ b/drivers/i2c/busses/i2c-viapro.c @@ -321,7 +321,6 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter vt596_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_SMBUS_VIA2, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-voodoo3.c b/drivers/i2c/busses/i2c-voodoo3.c index 1d4ae26ba73..1a474acc0dd 100644 --- a/drivers/i2c/busses/i2c-voodoo3.c +++ b/drivers/i2c/busses/i2c-voodoo3.c @@ -163,7 +163,6 @@ static struct i2c_algo_bit_data voo_i2c_bit_data = { static struct i2c_adapter voodoo3_i2c_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_B_VOO, .class = I2C_CLASS_TV_ANALOG, .name = "I2C Voodoo3/Banshee adapter", .algo_data = &voo_i2c_bit_data, @@ -180,7 +179,6 @@ static struct i2c_algo_bit_data voo_ddc_bit_data = { static struct i2c_adapter voodoo3_ddc_adapter = { .owner = THIS_MODULE, - .id = I2C_HW_B_VOO, .class = I2C_CLASS_DDC, .name = "DDC Voodoo3/Banshee adapter", .algo_data = &voo_ddc_bit_data, diff --git a/drivers/i2c/busses/scx200_acb.c b/drivers/i2c/busses/scx200_acb.c index ed794b145a1..648ecc6f60e 100644 --- a/drivers/i2c/busses/scx200_acb.c +++ b/drivers/i2c/busses/scx200_acb.c @@ -440,7 +440,6 @@ static __init struct scx200_acb_iface *scx200_create_iface(const char *text, i2c_set_adapdata(adapter, iface); snprintf(adapter->name, sizeof(adapter->name), "%s ACB%d", text, index); adapter->owner = THIS_MODULE; - adapter->id = I2C_HW_SMBUS_SCX200; adapter->algo = &scx200_acb_algorithm; adapter->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; adapter->dev.parent = dev; diff --git a/drivers/i2c/busses/scx200_i2c.c b/drivers/i2c/busses/scx200_i2c.c index e4c98539c51..162b74a0488 100644 --- a/drivers/i2c/busses/scx200_i2c.c +++ b/drivers/i2c/busses/scx200_i2c.c @@ -82,7 +82,6 @@ static struct i2c_algo_bit_data scx200_i2c_data = { static struct i2c_adapter scx200_i2c_ops = { .owner = THIS_MODULE, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, - .id = I2C_HW_B_SCX200, .algo_data = &scx200_i2c_data, .name = "NatSemi SCx200 I2C", }; -- cgit v1.2.3-70-g09d2 From 5195e5093bb7d30dbf057b260005cb4ab9761168 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 26 Jan 2009 21:19:53 +0100 Subject: i2c: Move at24 to drivers/misc/eeprom As drivers/i2c/chips is going to go away, move the driver to drivers/misc/eeprom. Other eeprom drivers may be moved here later, too. Update Kconfig text to specify this driver as I2C. Signed-off-by: Wolfram Sang Signed-off-by: Jean Delvare --- drivers/i2c/chips/Kconfig | 26 -- drivers/i2c/chips/Makefile | 1 - drivers/i2c/chips/at24.c | 582 ------------------------------------------- drivers/misc/Kconfig | 1 + drivers/misc/Makefile | 1 + drivers/misc/eeprom/Kconfig | 29 +++ drivers/misc/eeprom/Makefile | 1 + drivers/misc/eeprom/at24.c | 582 +++++++++++++++++++++++++++++++++++++++++++ 8 files changed, 614 insertions(+), 609 deletions(-) delete mode 100644 drivers/i2c/chips/at24.c create mode 100644 drivers/misc/eeprom/Kconfig create mode 100644 drivers/misc/eeprom/Makefile create mode 100644 drivers/misc/eeprom/at24.c (limited to 'drivers/i2c') diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index b9bef04b7be..b58e77056b2 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -16,32 +16,6 @@ config DS1682 This driver can also be built as a module. If so, the module will be called ds1682. -config AT24 - tristate "EEPROMs from most vendors" - depends on SYSFS && EXPERIMENTAL - help - Enable this driver to get read/write support to most I2C EEPROMs, - after you configure the driver to know about each EEPROM on - your target board. Use these generic chip names, instead of - vendor-specific ones like at24c64 or 24lc02: - - 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08, - 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024 - - Unless you like data loss puzzles, always be sure that any chip - you configure as a 24c32 (32 kbit) or larger is NOT really a - 24c16 (16 kbit) or smaller, and vice versa. Marking the chip - as read-only won't help recover from this. Also, if your chip - has any software write-protect mechanism you may want to review the - code to make sure this driver won't turn it on by accident. - - If you use this with an SMBus adapter instead of an I2C adapter, - full functionality is not available. Only smaller devices are - supported (24c16 and below, max 4 kByte). - - This driver can also be built as a module. If so, the module - will be called at24. - config SENSORS_EEPROM tristate "EEPROM reader" depends on EXPERIMENTAL diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index 00fcb5193ac..5c14776eb76 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -11,7 +11,6 @@ # obj-$(CONFIG_DS1682) += ds1682.o -obj-$(CONFIG_AT24) += at24.o obj-$(CONFIG_SENSORS_EEPROM) += eeprom.o obj-$(CONFIG_SENSORS_MAX6875) += max6875.o obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o diff --git a/drivers/i2c/chips/at24.c b/drivers/i2c/chips/at24.c deleted file mode 100644 index d4775528abc..00000000000 --- a/drivers/i2c/chips/at24.c +++ /dev/null @@ -1,582 +0,0 @@ -/* - * at24.c - handle most I2C EEPROMs - * - * Copyright (C) 2005-2007 David Brownell - * Copyright (C) 2008 Wolfram Sang, Pengutronix - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -/* - * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable. - * Differences between different vendor product lines (like Atmel AT24C or - * MicroChip 24LC, etc) won't much matter for typical read/write access. - * There are also I2C RAM chips, likewise interchangeable. One example - * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes). - * - * However, misconfiguration can lose data. "Set 16-bit memory address" - * to a part with 8-bit addressing will overwrite data. Writing with too - * big a page size also loses data. And it's not safe to assume that the - * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC - * uses 0x51, for just one example. - * - * Accordingly, explicit board-specific configuration data should be used - * in almost all cases. (One partial exception is an SMBus used to access - * "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.) - * - * So this driver uses "new style" I2C driver binding, expecting to be - * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or - * similar kernel-resident tables; or, configuration data coming from - * a bootloader. - * - * Other than binding model, current differences from "eeprom" driver are - * that this one handles write access and isn't restricted to 24c02 devices. - * It also handles larger devices (32 kbit and up) with two-byte addresses, - * which won't work on pure SMBus systems. - */ - -struct at24_data { - struct at24_platform_data chip; - bool use_smbus; - - /* - * Lock protects against activities from other Linux tasks, - * but not from changes by other I2C masters. - */ - struct mutex lock; - struct bin_attribute bin; - - u8 *writebuf; - unsigned write_max; - unsigned num_addresses; - - /* - * Some chips tie up multiple I2C addresses; dummy devices reserve - * them for us, and we'll use them with SMBus calls. - */ - struct i2c_client *client[]; -}; - -/* - * This parameter is to help this driver avoid blocking other drivers out - * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C - * clock, one 256 byte read takes about 1/43 second which is excessive; - * but the 1/170 second it takes at 400 kHz may be quite reasonable; and - * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible. - * - * This value is forced to be a power of two so that writes align on pages. - */ -static unsigned io_limit = 128; -module_param(io_limit, uint, 0); -MODULE_PARM_DESC(io_limit, "Maximum bytes per I/O (default 128)"); - -/* - * Specs often allow 5 msec for a page write, sometimes 20 msec; - * it's important to recover from write timeouts. - */ -static unsigned write_timeout = 25; -module_param(write_timeout, uint, 0); -MODULE_PARM_DESC(write_timeout, "Time (in ms) to try writes (default 25)"); - -#define AT24_SIZE_BYTELEN 5 -#define AT24_SIZE_FLAGS 8 - -#define AT24_BITMASK(x) (BIT(x) - 1) - -/* create non-zero magic value for given eeprom parameters */ -#define AT24_DEVICE_MAGIC(_len, _flags) \ - ((1 << AT24_SIZE_FLAGS | (_flags)) \ - << AT24_SIZE_BYTELEN | ilog2(_len)) - -static const struct i2c_device_id at24_ids[] = { - /* needs 8 addresses as A0-A2 are ignored */ - { "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) }, - /* old variants can't be handled with this generic entry! */ - { "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) }, - { "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) }, - /* spd is a 24c02 in memory DIMMs */ - { "spd", AT24_DEVICE_MAGIC(2048 / 8, - AT24_FLAG_READONLY | AT24_FLAG_IRUGO) }, - { "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) }, - /* 24rf08 quirk is handled at i2c-core */ - { "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) }, - { "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) }, - { "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) }, - { "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) }, - { "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) }, - { "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) }, - { "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) }, - { "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16) }, - { "at24", 0 }, - { /* END OF LIST */ } -}; -MODULE_DEVICE_TABLE(i2c, at24_ids); - -/*-------------------------------------------------------------------------*/ - -/* - * This routine supports chips which consume multiple I2C addresses. It - * computes the addressing information to be used for a given r/w request. - * Assumes that sanity checks for offset happened at sysfs-layer. - */ -static struct i2c_client *at24_translate_offset(struct at24_data *at24, - unsigned *offset) -{ - unsigned i; - - if (at24->chip.flags & AT24_FLAG_ADDR16) { - i = *offset >> 16; - *offset &= 0xffff; - } else { - i = *offset >> 8; - *offset &= 0xff; - } - - return at24->client[i]; -} - -static ssize_t at24_eeprom_read(struct at24_data *at24, char *buf, - unsigned offset, size_t count) -{ - struct i2c_msg msg[2]; - u8 msgbuf[2]; - struct i2c_client *client; - int status, i; - - memset(msg, 0, sizeof(msg)); - - /* - * REVISIT some multi-address chips don't rollover page reads to - * the next slave address, so we may need to truncate the count. - * Those chips might need another quirk flag. - * - * If the real hardware used four adjacent 24c02 chips and that - * were misconfigured as one 24c08, that would be a similar effect: - * one "eeprom" file not four, but larger reads would fail when - * they crossed certain pages. - */ - - /* - * Slave address and byte offset derive from the offset. Always - * set the byte address; on a multi-master board, another master - * may have changed the chip's "current" address pointer. - */ - client = at24_translate_offset(at24, &offset); - - if (count > io_limit) - count = io_limit; - - /* Smaller eeproms can work given some SMBus extension calls */ - if (at24->use_smbus) { - if (count > I2C_SMBUS_BLOCK_MAX) - count = I2C_SMBUS_BLOCK_MAX; - status = i2c_smbus_read_i2c_block_data(client, offset, - count, buf); - dev_dbg(&client->dev, "smbus read %zu@%d --> %d\n", - count, offset, status); - return (status < 0) ? -EIO : status; - } - - /* - * When we have a better choice than SMBus calls, use a combined - * I2C message. Write address; then read up to io_limit data bytes. - * Note that read page rollover helps us here (unlike writes). - * msgbuf is u8 and will cast to our needs. - */ - i = 0; - if (at24->chip.flags & AT24_FLAG_ADDR16) - msgbuf[i++] = offset >> 8; - msgbuf[i++] = offset; - - msg[0].addr = client->addr; - msg[0].buf = msgbuf; - msg[0].len = i; - - msg[1].addr = client->addr; - msg[1].flags = I2C_M_RD; - msg[1].buf = buf; - msg[1].len = count; - - status = i2c_transfer(client->adapter, msg, 2); - dev_dbg(&client->dev, "i2c read %zu@%d --> %d\n", - count, offset, status); - - if (status == 2) - return count; - else if (status >= 0) - return -EIO; - else - return status; -} - -static ssize_t at24_bin_read(struct kobject *kobj, struct bin_attribute *attr, - char *buf, loff_t off, size_t count) -{ - struct at24_data *at24; - ssize_t retval = 0; - - at24 = dev_get_drvdata(container_of(kobj, struct device, kobj)); - - if (unlikely(!count)) - return count; - - /* - * Read data from chip, protecting against concurrent updates - * from this host, but not from other I2C masters. - */ - mutex_lock(&at24->lock); - - while (count) { - ssize_t status; - - status = at24_eeprom_read(at24, buf, off, count); - if (status <= 0) { - if (retval == 0) - retval = status; - break; - } - buf += status; - off += status; - count -= status; - retval += status; - } - - mutex_unlock(&at24->lock); - - return retval; -} - - -/* - * REVISIT: export at24_bin{read,write}() to let other kernel code use - * eeprom data. For example, it might hold a board's Ethernet address, or - * board-specific calibration data generated on the manufacturing floor. - */ - - -/* - * Note that if the hardware write-protect pin is pulled high, the whole - * chip is normally write protected. But there are plenty of product - * variants here, including OTP fuses and partial chip protect. - * - * We only use page mode writes; the alternative is sloooow. This routine - * writes at most one page. - */ -static ssize_t at24_eeprom_write(struct at24_data *at24, char *buf, - unsigned offset, size_t count) -{ - struct i2c_client *client; - struct i2c_msg msg; - ssize_t status; - unsigned long timeout, write_time; - unsigned next_page; - - /* Get corresponding I2C address and adjust offset */ - client = at24_translate_offset(at24, &offset); - - /* write_max is at most a page */ - if (count > at24->write_max) - count = at24->write_max; - - /* Never roll over backwards, to the start of this page */ - next_page = roundup(offset + 1, at24->chip.page_size); - if (offset + count > next_page) - count = next_page - offset; - - /* If we'll use I2C calls for I/O, set up the message */ - if (!at24->use_smbus) { - int i = 0; - - msg.addr = client->addr; - msg.flags = 0; - - /* msg.buf is u8 and casts will mask the values */ - msg.buf = at24->writebuf; - if (at24->chip.flags & AT24_FLAG_ADDR16) - msg.buf[i++] = offset >> 8; - - msg.buf[i++] = offset; - memcpy(&msg.buf[i], buf, count); - msg.len = i + count; - } - - /* - * Writes fail if the previous one didn't complete yet. We may - * loop a few times until this one succeeds, waiting at least - * long enough for one entire page write to work. - */ - timeout = jiffies + msecs_to_jiffies(write_timeout); - do { - write_time = jiffies; - if (at24->use_smbus) { - status = i2c_smbus_write_i2c_block_data(client, - offset, count, buf); - if (status == 0) - status = count; - } else { - status = i2c_transfer(client->adapter, &msg, 1); - if (status == 1) - status = count; - } - dev_dbg(&client->dev, "write %zu@%d --> %zd (%ld)\n", - count, offset, status, jiffies); - - if (status == count) - return count; - - /* REVISIT: at HZ=100, this is sloooow */ - msleep(1); - } while (time_before(write_time, timeout)); - - return -ETIMEDOUT; -} - -static ssize_t at24_bin_write(struct kobject *kobj, struct bin_attribute *attr, - char *buf, loff_t off, size_t count) -{ - struct at24_data *at24; - ssize_t retval = 0; - - at24 = dev_get_drvdata(container_of(kobj, struct device, kobj)); - - if (unlikely(!count)) - return count; - - /* - * Write data to chip, protecting against concurrent updates - * from this host, but not from other I2C masters. - */ - mutex_lock(&at24->lock); - - while (count) { - ssize_t status; - - status = at24_eeprom_write(at24, buf, off, count); - if (status <= 0) { - if (retval == 0) - retval = status; - break; - } - buf += status; - off += status; - count -= status; - retval += status; - } - - mutex_unlock(&at24->lock); - - return retval; -} - -/*-------------------------------------------------------------------------*/ - -static int at24_probe(struct i2c_client *client, const struct i2c_device_id *id) -{ - struct at24_platform_data chip; - bool writable; - bool use_smbus = false; - struct at24_data *at24; - int err; - unsigned i, num_addresses; - kernel_ulong_t magic; - - if (client->dev.platform_data) { - chip = *(struct at24_platform_data *)client->dev.platform_data; - } else { - if (!id->driver_data) { - err = -ENODEV; - goto err_out; - } - magic = id->driver_data; - chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN)); - magic >>= AT24_SIZE_BYTELEN; - chip.flags = magic & AT24_BITMASK(AT24_SIZE_FLAGS); - /* - * This is slow, but we can't know all eeproms, so we better - * play safe. Specifying custom eeprom-types via platform_data - * is recommended anyhow. - */ - chip.page_size = 1; - } - - if (!is_power_of_2(chip.byte_len)) - dev_warn(&client->dev, - "byte_len looks suspicious (no power of 2)!\n"); - if (!is_power_of_2(chip.page_size)) - dev_warn(&client->dev, - "page_size looks suspicious (no power of 2)!\n"); - - /* Use I2C operations unless we're stuck with SMBus extensions. */ - if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { - if (chip.flags & AT24_FLAG_ADDR16) { - err = -EPFNOSUPPORT; - goto err_out; - } - if (!i2c_check_functionality(client->adapter, - I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { - err = -EPFNOSUPPORT; - goto err_out; - } - use_smbus = true; - } - - if (chip.flags & AT24_FLAG_TAKE8ADDR) - num_addresses = 8; - else - num_addresses = DIV_ROUND_UP(chip.byte_len, - (chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256); - - at24 = kzalloc(sizeof(struct at24_data) + - num_addresses * sizeof(struct i2c_client *), GFP_KERNEL); - if (!at24) { - err = -ENOMEM; - goto err_out; - } - - mutex_init(&at24->lock); - at24->use_smbus = use_smbus; - at24->chip = chip; - at24->num_addresses = num_addresses; - - /* - * Export the EEPROM bytes through sysfs, since that's convenient. - * By default, only root should see the data (maybe passwords etc) - */ - at24->bin.attr.name = "eeprom"; - at24->bin.attr.mode = chip.flags & AT24_FLAG_IRUGO ? S_IRUGO : S_IRUSR; - at24->bin.read = at24_bin_read; - at24->bin.size = chip.byte_len; - - writable = !(chip.flags & AT24_FLAG_READONLY); - if (writable) { - if (!use_smbus || i2c_check_functionality(client->adapter, - I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) { - - unsigned write_max = chip.page_size; - - at24->bin.write = at24_bin_write; - at24->bin.attr.mode |= S_IWUSR; - - if (write_max > io_limit) - write_max = io_limit; - if (use_smbus && write_max > I2C_SMBUS_BLOCK_MAX) - write_max = I2C_SMBUS_BLOCK_MAX; - at24->write_max = write_max; - - /* buffer (data + address at the beginning) */ - at24->writebuf = kmalloc(write_max + 2, GFP_KERNEL); - if (!at24->writebuf) { - err = -ENOMEM; - goto err_struct; - } - } else { - dev_warn(&client->dev, - "cannot write due to controller restrictions."); - } - } - - at24->client[0] = client; - - /* use dummy devices for multiple-address chips */ - for (i = 1; i < num_addresses; i++) { - at24->client[i] = i2c_new_dummy(client->adapter, - client->addr + i); - if (!at24->client[i]) { - dev_err(&client->dev, "address 0x%02x unavailable\n", - client->addr + i); - err = -EADDRINUSE; - goto err_clients; - } - } - - err = sysfs_create_bin_file(&client->dev.kobj, &at24->bin); - if (err) - goto err_clients; - - i2c_set_clientdata(client, at24); - - dev_info(&client->dev, "%zu byte %s EEPROM %s\n", - at24->bin.size, client->name, - writable ? "(writable)" : "(read-only)"); - dev_dbg(&client->dev, - "page_size %d, num_addresses %d, write_max %d%s\n", - chip.page_size, num_addresses, - at24->write_max, - use_smbus ? ", use_smbus" : ""); - - return 0; - -err_clients: - for (i = 1; i < num_addresses; i++) - if (at24->client[i]) - i2c_unregister_device(at24->client[i]); - - kfree(at24->writebuf); -err_struct: - kfree(at24); -err_out: - dev_dbg(&client->dev, "probe error %d\n", err); - return err; -} - -static int __devexit at24_remove(struct i2c_client *client) -{ - struct at24_data *at24; - int i; - - at24 = i2c_get_clientdata(client); - sysfs_remove_bin_file(&client->dev.kobj, &at24->bin); - - for (i = 1; i < at24->num_addresses; i++) - i2c_unregister_device(at24->client[i]); - - kfree(at24->writebuf); - kfree(at24); - i2c_set_clientdata(client, NULL); - return 0; -} - -/*-------------------------------------------------------------------------*/ - -static struct i2c_driver at24_driver = { - .driver = { - .name = "at24", - .owner = THIS_MODULE, - }, - .probe = at24_probe, - .remove = __devexit_p(at24_remove), - .id_table = at24_ids, -}; - -static int __init at24_init(void) -{ - io_limit = rounddown_pow_of_two(io_limit); - return i2c_add_driver(&at24_driver); -} -module_init(at24_init); - -static void __exit at24_exit(void) -{ - i2c_del_driver(&at24_driver); -} -module_exit(at24_exit); - -MODULE_DESCRIPTION("Driver for most I2C EEPROMs"); -MODULE_AUTHOR("David Brownell and Wolfram Sang"); -MODULE_LICENSE("GPL"); diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index 419c378bd24..6c9cd9d3008 100644 --- a/drivers/misc/Kconfig +++ b/drivers/misc/Kconfig @@ -231,5 +231,6 @@ config DELL_LAPTOP laptops. source "drivers/misc/c2port/Kconfig" +source "drivers/misc/eeprom/Kconfig" endif # MISC_DEVICES diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index d5749a7bc77..0ec23203c99 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -20,3 +20,4 @@ obj-$(CONFIG_SGI_XP) += sgi-xp/ obj-$(CONFIG_SGI_GRU) += sgi-gru/ obj-$(CONFIG_HP_ILO) += hpilo.o obj-$(CONFIG_C2PORT) += c2port/ +obj-y += eeprom/ diff --git a/drivers/misc/eeprom/Kconfig b/drivers/misc/eeprom/Kconfig new file mode 100644 index 00000000000..0b21778b7d1 --- /dev/null +++ b/drivers/misc/eeprom/Kconfig @@ -0,0 +1,29 @@ +menu "EEPROM support" + +config AT24 + tristate "I2C EEPROMs from most vendors" + depends on I2C && SYSFS && EXPERIMENTAL + help + Enable this driver to get read/write support to most I2C EEPROMs, + after you configure the driver to know about each EEPROM on + your target board. Use these generic chip names, instead of + vendor-specific ones like at24c64 or 24lc02: + + 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08, + 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024 + + Unless you like data loss puzzles, always be sure that any chip + you configure as a 24c32 (32 kbit) or larger is NOT really a + 24c16 (16 kbit) or smaller, and vice versa. Marking the chip + as read-only won't help recover from this. Also, if your chip + has any software write-protect mechanism you may want to review the + code to make sure this driver won't turn it on by accident. + + If you use this with an SMBus adapter instead of an I2C adapter, + full functionality is not available. Only smaller devices are + supported (24c16 and below, max 4 kByte). + + This driver can also be built as a module. If so, the module + will be called at24. + +endmenu diff --git a/drivers/misc/eeprom/Makefile b/drivers/misc/eeprom/Makefile new file mode 100644 index 00000000000..72cd478eb53 --- /dev/null +++ b/drivers/misc/eeprom/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_AT24) += at24.o diff --git a/drivers/misc/eeprom/at24.c b/drivers/misc/eeprom/at24.c new file mode 100644 index 00000000000..d4775528abc --- /dev/null +++ b/drivers/misc/eeprom/at24.c @@ -0,0 +1,582 @@ +/* + * at24.c - handle most I2C EEPROMs + * + * Copyright (C) 2005-2007 David Brownell + * Copyright (C) 2008 Wolfram Sang, Pengutronix + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable. + * Differences between different vendor product lines (like Atmel AT24C or + * MicroChip 24LC, etc) won't much matter for typical read/write access. + * There are also I2C RAM chips, likewise interchangeable. One example + * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes). + * + * However, misconfiguration can lose data. "Set 16-bit memory address" + * to a part with 8-bit addressing will overwrite data. Writing with too + * big a page size also loses data. And it's not safe to assume that the + * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC + * uses 0x51, for just one example. + * + * Accordingly, explicit board-specific configuration data should be used + * in almost all cases. (One partial exception is an SMBus used to access + * "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.) + * + * So this driver uses "new style" I2C driver binding, expecting to be + * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or + * similar kernel-resident tables; or, configuration data coming from + * a bootloader. + * + * Other than binding model, current differences from "eeprom" driver are + * that this one handles write access and isn't restricted to 24c02 devices. + * It also handles larger devices (32 kbit and up) with two-byte addresses, + * which won't work on pure SMBus systems. + */ + +struct at24_data { + struct at24_platform_data chip; + bool use_smbus; + + /* + * Lock protects against activities from other Linux tasks, + * but not from changes by other I2C masters. + */ + struct mutex lock; + struct bin_attribute bin; + + u8 *writebuf; + unsigned write_max; + unsigned num_addresses; + + /* + * Some chips tie up multiple I2C addresses; dummy devices reserve + * them for us, and we'll use them with SMBus calls. + */ + struct i2c_client *client[]; +}; + +/* + * This parameter is to help this driver avoid blocking other drivers out + * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C + * clock, one 256 byte read takes about 1/43 second which is excessive; + * but the 1/170 second it takes at 400 kHz may be quite reasonable; and + * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible. + * + * This value is forced to be a power of two so that writes align on pages. + */ +static unsigned io_limit = 128; +module_param(io_limit, uint, 0); +MODULE_PARM_DESC(io_limit, "Maximum bytes per I/O (default 128)"); + +/* + * Specs often allow 5 msec for a page write, sometimes 20 msec; + * it's important to recover from write timeouts. + */ +static unsigned write_timeout = 25; +module_param(write_timeout, uint, 0); +MODULE_PARM_DESC(write_timeout, "Time (in ms) to try writes (default 25)"); + +#define AT24_SIZE_BYTELEN 5 +#define AT24_SIZE_FLAGS 8 + +#define AT24_BITMASK(x) (BIT(x) - 1) + +/* create non-zero magic value for given eeprom parameters */ +#define AT24_DEVICE_MAGIC(_len, _flags) \ + ((1 << AT24_SIZE_FLAGS | (_flags)) \ + << AT24_SIZE_BYTELEN | ilog2(_len)) + +static const struct i2c_device_id at24_ids[] = { + /* needs 8 addresses as A0-A2 are ignored */ + { "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) }, + /* old variants can't be handled with this generic entry! */ + { "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) }, + { "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) }, + /* spd is a 24c02 in memory DIMMs */ + { "spd", AT24_DEVICE_MAGIC(2048 / 8, + AT24_FLAG_READONLY | AT24_FLAG_IRUGO) }, + { "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) }, + /* 24rf08 quirk is handled at i2c-core */ + { "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) }, + { "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) }, + { "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) }, + { "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) }, + { "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) }, + { "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) }, + { "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) }, + { "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16) }, + { "at24", 0 }, + { /* END OF LIST */ } +}; +MODULE_DEVICE_TABLE(i2c, at24_ids); + +/*-------------------------------------------------------------------------*/ + +/* + * This routine supports chips which consume multiple I2C addresses. It + * computes the addressing information to be used for a given r/w request. + * Assumes that sanity checks for offset happened at sysfs-layer. + */ +static struct i2c_client *at24_translate_offset(struct at24_data *at24, + unsigned *offset) +{ + unsigned i; + + if (at24->chip.flags & AT24_FLAG_ADDR16) { + i = *offset >> 16; + *offset &= 0xffff; + } else { + i = *offset >> 8; + *offset &= 0xff; + } + + return at24->client[i]; +} + +static ssize_t at24_eeprom_read(struct at24_data *at24, char *buf, + unsigned offset, size_t count) +{ + struct i2c_msg msg[2]; + u8 msgbuf[2]; + struct i2c_client *client; + int status, i; + + memset(msg, 0, sizeof(msg)); + + /* + * REVISIT some multi-address chips don't rollover page reads to + * the next slave address, so we may need to truncate the count. + * Those chips might need another quirk flag. + * + * If the real hardware used four adjacent 24c02 chips and that + * were misconfigured as one 24c08, that would be a similar effect: + * one "eeprom" file not four, but larger reads would fail when + * they crossed certain pages. + */ + + /* + * Slave address and byte offset derive from the offset. Always + * set the byte address; on a multi-master board, another master + * may have changed the chip's "current" address pointer. + */ + client = at24_translate_offset(at24, &offset); + + if (count > io_limit) + count = io_limit; + + /* Smaller eeproms can work given some SMBus extension calls */ + if (at24->use_smbus) { + if (count > I2C_SMBUS_BLOCK_MAX) + count = I2C_SMBUS_BLOCK_MAX; + status = i2c_smbus_read_i2c_block_data(client, offset, + count, buf); + dev_dbg(&client->dev, "smbus read %zu@%d --> %d\n", + count, offset, status); + return (status < 0) ? -EIO : status; + } + + /* + * When we have a better choice than SMBus calls, use a combined + * I2C message. Write address; then read up to io_limit data bytes. + * Note that read page rollover helps us here (unlike writes). + * msgbuf is u8 and will cast to our needs. + */ + i = 0; + if (at24->chip.flags & AT24_FLAG_ADDR16) + msgbuf[i++] = offset >> 8; + msgbuf[i++] = offset; + + msg[0].addr = client->addr; + msg[0].buf = msgbuf; + msg[0].len = i; + + msg[1].addr = client->addr; + msg[1].flags = I2C_M_RD; + msg[1].buf = buf; + msg[1].len = count; + + status = i2c_transfer(client->adapter, msg, 2); + dev_dbg(&client->dev, "i2c read %zu@%d --> %d\n", + count, offset, status); + + if (status == 2) + return count; + else if (status >= 0) + return -EIO; + else + return status; +} + +static ssize_t at24_bin_read(struct kobject *kobj, struct bin_attribute *attr, + char *buf, loff_t off, size_t count) +{ + struct at24_data *at24; + ssize_t retval = 0; + + at24 = dev_get_drvdata(container_of(kobj, struct device, kobj)); + + if (unlikely(!count)) + return count; + + /* + * Read data from chip, protecting against concurrent updates + * from this host, but not from other I2C masters. + */ + mutex_lock(&at24->lock); + + while (count) { + ssize_t status; + + status = at24_eeprom_read(at24, buf, off, count); + if (status <= 0) { + if (retval == 0) + retval = status; + break; + } + buf += status; + off += status; + count -= status; + retval += status; + } + + mutex_unlock(&at24->lock); + + return retval; +} + + +/* + * REVISIT: export at24_bin{read,write}() to let other kernel code use + * eeprom data. For example, it might hold a board's Ethernet address, or + * board-specific calibration data generated on the manufacturing floor. + */ + + +/* + * Note that if the hardware write-protect pin is pulled high, the whole + * chip is normally write protected. But there are plenty of product + * variants here, including OTP fuses and partial chip protect. + * + * We only use page mode writes; the alternative is sloooow. This routine + * writes at most one page. + */ +static ssize_t at24_eeprom_write(struct at24_data *at24, char *buf, + unsigned offset, size_t count) +{ + struct i2c_client *client; + struct i2c_msg msg; + ssize_t status; + unsigned long timeout, write_time; + unsigned next_page; + + /* Get corresponding I2C address and adjust offset */ + client = at24_translate_offset(at24, &offset); + + /* write_max is at most a page */ + if (count > at24->write_max) + count = at24->write_max; + + /* Never roll over backwards, to the start of this page */ + next_page = roundup(offset + 1, at24->chip.page_size); + if (offset + count > next_page) + count = next_page - offset; + + /* If we'll use I2C calls for I/O, set up the message */ + if (!at24->use_smbus) { + int i = 0; + + msg.addr = client->addr; + msg.flags = 0; + + /* msg.buf is u8 and casts will mask the values */ + msg.buf = at24->writebuf; + if (at24->chip.flags & AT24_FLAG_ADDR16) + msg.buf[i++] = offset >> 8; + + msg.buf[i++] = offset; + memcpy(&msg.buf[i], buf, count); + msg.len = i + count; + } + + /* + * Writes fail if the previous one didn't complete yet. We may + * loop a few times until this one succeeds, waiting at least + * long enough for one entire page write to work. + */ + timeout = jiffies + msecs_to_jiffies(write_timeout); + do { + write_time = jiffies; + if (at24->use_smbus) { + status = i2c_smbus_write_i2c_block_data(client, + offset, count, buf); + if (status == 0) + status = count; + } else { + status = i2c_transfer(client->adapter, &msg, 1); + if (status == 1) + status = count; + } + dev_dbg(&client->dev, "write %zu@%d --> %zd (%ld)\n", + count, offset, status, jiffies); + + if (status == count) + return count; + + /* REVISIT: at HZ=100, this is sloooow */ + msleep(1); + } while (time_before(write_time, timeout)); + + return -ETIMEDOUT; +} + +static ssize_t at24_bin_write(struct kobject *kobj, struct bin_attribute *attr, + char *buf, loff_t off, size_t count) +{ + struct at24_data *at24; + ssize_t retval = 0; + + at24 = dev_get_drvdata(container_of(kobj, struct device, kobj)); + + if (unlikely(!count)) + return count; + + /* + * Write data to chip, protecting against concurrent updates + * from this host, but not from other I2C masters. + */ + mutex_lock(&at24->lock); + + while (count) { + ssize_t status; + + status = at24_eeprom_write(at24, buf, off, count); + if (status <= 0) { + if (retval == 0) + retval = status; + break; + } + buf += status; + off += status; + count -= status; + retval += status; + } + + mutex_unlock(&at24->lock); + + return retval; +} + +/*-------------------------------------------------------------------------*/ + +static int at24_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + struct at24_platform_data chip; + bool writable; + bool use_smbus = false; + struct at24_data *at24; + int err; + unsigned i, num_addresses; + kernel_ulong_t magic; + + if (client->dev.platform_data) { + chip = *(struct at24_platform_data *)client->dev.platform_data; + } else { + if (!id->driver_data) { + err = -ENODEV; + goto err_out; + } + magic = id->driver_data; + chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN)); + magic >>= AT24_SIZE_BYTELEN; + chip.flags = magic & AT24_BITMASK(AT24_SIZE_FLAGS); + /* + * This is slow, but we can't know all eeproms, so we better + * play safe. Specifying custom eeprom-types via platform_data + * is recommended anyhow. + */ + chip.page_size = 1; + } + + if (!is_power_of_2(chip.byte_len)) + dev_warn(&client->dev, + "byte_len looks suspicious (no power of 2)!\n"); + if (!is_power_of_2(chip.page_size)) + dev_warn(&client->dev, + "page_size looks suspicious (no power of 2)!\n"); + + /* Use I2C operations unless we're stuck with SMBus extensions. */ + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { + if (chip.flags & AT24_FLAG_ADDR16) { + err = -EPFNOSUPPORT; + goto err_out; + } + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { + err = -EPFNOSUPPORT; + goto err_out; + } + use_smbus = true; + } + + if (chip.flags & AT24_FLAG_TAKE8ADDR) + num_addresses = 8; + else + num_addresses = DIV_ROUND_UP(chip.byte_len, + (chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256); + + at24 = kzalloc(sizeof(struct at24_data) + + num_addresses * sizeof(struct i2c_client *), GFP_KERNEL); + if (!at24) { + err = -ENOMEM; + goto err_out; + } + + mutex_init(&at24->lock); + at24->use_smbus = use_smbus; + at24->chip = chip; + at24->num_addresses = num_addresses; + + /* + * Export the EEPROM bytes through sysfs, since that's convenient. + * By default, only root should see the data (maybe passwords etc) + */ + at24->bin.attr.name = "eeprom"; + at24->bin.attr.mode = chip.flags & AT24_FLAG_IRUGO ? S_IRUGO : S_IRUSR; + at24->bin.read = at24_bin_read; + at24->bin.size = chip.byte_len; + + writable = !(chip.flags & AT24_FLAG_READONLY); + if (writable) { + if (!use_smbus || i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) { + + unsigned write_max = chip.page_size; + + at24->bin.write = at24_bin_write; + at24->bin.attr.mode |= S_IWUSR; + + if (write_max > io_limit) + write_max = io_limit; + if (use_smbus && write_max > I2C_SMBUS_BLOCK_MAX) + write_max = I2C_SMBUS_BLOCK_MAX; + at24->write_max = write_max; + + /* buffer (data + address at the beginning) */ + at24->writebuf = kmalloc(write_max + 2, GFP_KERNEL); + if (!at24->writebuf) { + err = -ENOMEM; + goto err_struct; + } + } else { + dev_warn(&client->dev, + "cannot write due to controller restrictions."); + } + } + + at24->client[0] = client; + + /* use dummy devices for multiple-address chips */ + for (i = 1; i < num_addresses; i++) { + at24->client[i] = i2c_new_dummy(client->adapter, + client->addr + i); + if (!at24->client[i]) { + dev_err(&client->dev, "address 0x%02x unavailable\n", + client->addr + i); + err = -EADDRINUSE; + goto err_clients; + } + } + + err = sysfs_create_bin_file(&client->dev.kobj, &at24->bin); + if (err) + goto err_clients; + + i2c_set_clientdata(client, at24); + + dev_info(&client->dev, "%zu byte %s EEPROM %s\n", + at24->bin.size, client->name, + writable ? "(writable)" : "(read-only)"); + dev_dbg(&client->dev, + "page_size %d, num_addresses %d, write_max %d%s\n", + chip.page_size, num_addresses, + at24->write_max, + use_smbus ? ", use_smbus" : ""); + + return 0; + +err_clients: + for (i = 1; i < num_addresses; i++) + if (at24->client[i]) + i2c_unregister_device(at24->client[i]); + + kfree(at24->writebuf); +err_struct: + kfree(at24); +err_out: + dev_dbg(&client->dev, "probe error %d\n", err); + return err; +} + +static int __devexit at24_remove(struct i2c_client *client) +{ + struct at24_data *at24; + int i; + + at24 = i2c_get_clientdata(client); + sysfs_remove_bin_file(&client->dev.kobj, &at24->bin); + + for (i = 1; i < at24->num_addresses; i++) + i2c_unregister_device(at24->client[i]); + + kfree(at24->writebuf); + kfree(at24); + i2c_set_clientdata(client, NULL); + return 0; +} + +/*-------------------------------------------------------------------------*/ + +static struct i2c_driver at24_driver = { + .driver = { + .name = "at24", + .owner = THIS_MODULE, + }, + .probe = at24_probe, + .remove = __devexit_p(at24_remove), + .id_table = at24_ids, +}; + +static int __init at24_init(void) +{ + io_limit = rounddown_pow_of_two(io_limit); + return i2c_add_driver(&at24_driver); +} +module_init(at24_init); + +static void __exit at24_exit(void) +{ + i2c_del_driver(&at24_driver); +} +module_exit(at24_exit); + +MODULE_DESCRIPTION("Driver for most I2C EEPROMs"); +MODULE_AUTHOR("David Brownell and Wolfram Sang"); +MODULE_LICENSE("GPL"); -- cgit v1.2.3-70-g09d2 From 2e157888f132131f8877affd2785dcee4c227c1d Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 26 Jan 2009 21:19:53 +0100 Subject: i2c: Move old eeprom driver to /drivers/misc/eeprom Update Kconfig text to specify this driver as I2C. Signed-off-by: Wolfram Sang Signed-off-by: Jean Delvare --- drivers/i2c/chips/Kconfig | 11 -- drivers/i2c/chips/Makefile | 1 - drivers/i2c/chips/eeprom.c | 257 ------------------------------------------- drivers/misc/eeprom/Kconfig | 11 ++ drivers/misc/eeprom/Makefile | 1 + drivers/misc/eeprom/eeprom.c | 257 +++++++++++++++++++++++++++++++++++++++++++ 6 files changed, 269 insertions(+), 269 deletions(-) delete mode 100644 drivers/i2c/chips/eeprom.c create mode 100644 drivers/misc/eeprom/eeprom.c (limited to 'drivers/i2c') diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index b58e77056b2..c80312c1f38 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -16,17 +16,6 @@ config DS1682 This driver can also be built as a module. If so, the module will be called ds1682. -config SENSORS_EEPROM - tristate "EEPROM reader" - depends on EXPERIMENTAL - help - If you say yes here you get read-only access to the EEPROM data - available on modern memory DIMMs and Sony Vaio laptops. Such - EEPROMs could theoretically be available on other devices as well. - - This driver can also be built as a module. If so, the module - will be called eeprom. - config SENSORS_PCF8574 tristate "Philips PCF8574 and PCF8574A (DEPRECATED)" depends on EXPERIMENTAL && GPIO_PCF857X = "n" diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index 5c14776eb76..d142f238a2d 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -11,7 +11,6 @@ # obj-$(CONFIG_DS1682) += ds1682.o -obj-$(CONFIG_SENSORS_EEPROM) += eeprom.o obj-$(CONFIG_SENSORS_MAX6875) += max6875.o obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o diff --git a/drivers/i2c/chips/eeprom.c b/drivers/i2c/chips/eeprom.c deleted file mode 100644 index 2c27193aeaa..00000000000 --- a/drivers/i2c/chips/eeprom.c +++ /dev/null @@ -1,257 +0,0 @@ -/* - Copyright (C) 1998, 1999 Frodo Looijaard and - Philip Edelbrock - Copyright (C) 2003 Greg Kroah-Hartman - Copyright (C) 2003 IBM Corp. - Copyright (C) 2004 Jean Delvare - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ - -#include -#include -#include -#include -#include -#include -#include - -/* Addresses to scan */ -static const unsigned short normal_i2c[] = { 0x50, 0x51, 0x52, 0x53, 0x54, - 0x55, 0x56, 0x57, I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(eeprom); - - -/* Size of EEPROM in bytes */ -#define EEPROM_SIZE 256 - -/* possible types of eeprom devices */ -enum eeprom_nature { - UNKNOWN, - VAIO, -}; - -/* Each client has this additional data */ -struct eeprom_data { - struct mutex update_lock; - u8 valid; /* bitfield, bit!=0 if slice is valid */ - unsigned long last_updated[8]; /* In jiffies, 8 slices */ - u8 data[EEPROM_SIZE]; /* Register values */ - enum eeprom_nature nature; -}; - - -static void eeprom_update_client(struct i2c_client *client, u8 slice) -{ - struct eeprom_data *data = i2c_get_clientdata(client); - int i; - - mutex_lock(&data->update_lock); - - if (!(data->valid & (1 << slice)) || - time_after(jiffies, data->last_updated[slice] + 300 * HZ)) { - dev_dbg(&client->dev, "Starting eeprom update, slice %u\n", slice); - - if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { - for (i = slice << 5; i < (slice + 1) << 5; i += 32) - if (i2c_smbus_read_i2c_block_data(client, i, - 32, data->data + i) - != 32) - goto exit; - } else { - for (i = slice << 5; i < (slice + 1) << 5; i += 2) { - int word = i2c_smbus_read_word_data(client, i); - if (word < 0) - goto exit; - data->data[i] = word & 0xff; - data->data[i + 1] = word >> 8; - } - } - data->last_updated[slice] = jiffies; - data->valid |= (1 << slice); - } -exit: - mutex_unlock(&data->update_lock); -} - -static ssize_t eeprom_read(struct kobject *kobj, struct bin_attribute *bin_attr, - char *buf, loff_t off, size_t count) -{ - struct i2c_client *client = to_i2c_client(container_of(kobj, struct device, kobj)); - struct eeprom_data *data = i2c_get_clientdata(client); - u8 slice; - - if (off > EEPROM_SIZE) - return 0; - if (off + count > EEPROM_SIZE) - count = EEPROM_SIZE - off; - - /* Only refresh slices which contain requested bytes */ - for (slice = off >> 5; slice <= (off + count - 1) >> 5; slice++) - eeprom_update_client(client, slice); - - /* Hide Vaio private settings to regular users: - - BIOS passwords: bytes 0x00 to 0x0f - - UUID: bytes 0x10 to 0x1f - - Serial number: 0xc0 to 0xdf */ - if (data->nature == VAIO && !capable(CAP_SYS_ADMIN)) { - int i; - - for (i = 0; i < count; i++) { - if ((off + i <= 0x1f) || - (off + i >= 0xc0 && off + i <= 0xdf)) - buf[i] = 0; - else - buf[i] = data->data[off + i]; - } - } else { - memcpy(buf, &data->data[off], count); - } - - return count; -} - -static struct bin_attribute eeprom_attr = { - .attr = { - .name = "eeprom", - .mode = S_IRUGO, - }, - .size = EEPROM_SIZE, - .read = eeprom_read, -}; - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int eeprom_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - /* EDID EEPROMs are often 24C00 EEPROMs, which answer to all - addresses 0x50-0x57, but we only care about 0x50. So decline - attaching to addresses >= 0x51 on DDC buses */ - if (!(adapter->class & I2C_CLASS_SPD) && client->addr >= 0x51) - return -ENODEV; - - /* There are four ways we can read the EEPROM data: - (1) I2C block reads (faster, but unsupported by most adapters) - (2) Word reads (128% overhead) - (3) Consecutive byte reads (88% overhead, unsafe) - (4) Regular byte data reads (265% overhead) - The third and fourth methods are not implemented by this driver - because all known adapters support one of the first two. */ - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_WORD_DATA) - && !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) - return -ENODEV; - - strlcpy(info->type, "eeprom", I2C_NAME_SIZE); - - return 0; -} - -static int eeprom_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - struct i2c_adapter *adapter = client->adapter; - struct eeprom_data *data; - int err; - - if (!(data = kzalloc(sizeof(struct eeprom_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - memset(data->data, 0xff, EEPROM_SIZE); - i2c_set_clientdata(client, data); - mutex_init(&data->update_lock); - data->nature = UNKNOWN; - - /* Detect the Vaio nature of EEPROMs. - We use the "PCG-" or "VGN-" prefix as the signature. */ - if (client->addr == 0x57 - && i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA)) { - char name[4]; - - name[0] = i2c_smbus_read_byte_data(client, 0x80); - name[1] = i2c_smbus_read_byte_data(client, 0x81); - name[2] = i2c_smbus_read_byte_data(client, 0x82); - name[3] = i2c_smbus_read_byte_data(client, 0x83); - - if (!memcmp(name, "PCG-", 4) || !memcmp(name, "VGN-", 4)) { - dev_info(&client->dev, "Vaio EEPROM detected, " - "enabling privacy protection\n"); - data->nature = VAIO; - } - } - - /* create the sysfs eeprom file */ - err = sysfs_create_bin_file(&client->dev.kobj, &eeprom_attr); - if (err) - goto exit_kfree; - - return 0; - -exit_kfree: - kfree(data); -exit: - return err; -} - -static int eeprom_remove(struct i2c_client *client) -{ - sysfs_remove_bin_file(&client->dev.kobj, &eeprom_attr); - kfree(i2c_get_clientdata(client)); - - return 0; -} - -static const struct i2c_device_id eeprom_id[] = { - { "eeprom", 0 }, - { } -}; - -static struct i2c_driver eeprom_driver = { - .driver = { - .name = "eeprom", - }, - .probe = eeprom_probe, - .remove = eeprom_remove, - .id_table = eeprom_id, - - .class = I2C_CLASS_DDC | I2C_CLASS_SPD, - .detect = eeprom_detect, - .address_data = &addr_data, -}; - -static int __init eeprom_init(void) -{ - return i2c_add_driver(&eeprom_driver); -} - -static void __exit eeprom_exit(void) -{ - i2c_del_driver(&eeprom_driver); -} - - -MODULE_AUTHOR("Frodo Looijaard and " - "Philip Edelbrock and " - "Greg Kroah-Hartman "); -MODULE_DESCRIPTION("I2C EEPROM driver"); -MODULE_LICENSE("GPL"); - -module_init(eeprom_init); -module_exit(eeprom_exit); diff --git a/drivers/misc/eeprom/Kconfig b/drivers/misc/eeprom/Kconfig index 0b21778b7d1..3d31b664424 100644 --- a/drivers/misc/eeprom/Kconfig +++ b/drivers/misc/eeprom/Kconfig @@ -26,4 +26,15 @@ config AT24 This driver can also be built as a module. If so, the module will be called at24. +config SENSORS_EEPROM + tristate "Old I2C EEPROM reader" + depends on I2C && EXPERIMENTAL + help + If you say yes here you get read-only access to the EEPROM data + available on modern memory DIMMs and Sony Vaio laptops via I2C. Such + EEPROMs could theoretically be available on other devices as well. + + This driver can also be built as a module. If so, the module + will be called eeprom. + endmenu diff --git a/drivers/misc/eeprom/Makefile b/drivers/misc/eeprom/Makefile index 72cd478eb53..a3dad28f272 100644 --- a/drivers/misc/eeprom/Makefile +++ b/drivers/misc/eeprom/Makefile @@ -1 +1,2 @@ obj-$(CONFIG_AT24) += at24.o +obj-$(CONFIG_SENSORS_EEPROM) += eeprom.o diff --git a/drivers/misc/eeprom/eeprom.c b/drivers/misc/eeprom/eeprom.c new file mode 100644 index 00000000000..2c27193aeaa --- /dev/null +++ b/drivers/misc/eeprom/eeprom.c @@ -0,0 +1,257 @@ +/* + Copyright (C) 1998, 1999 Frodo Looijaard and + Philip Edelbrock + Copyright (C) 2003 Greg Kroah-Hartman + Copyright (C) 2003 IBM Corp. + Copyright (C) 2004 Jean Delvare + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +#include +#include +#include +#include +#include +#include +#include + +/* Addresses to scan */ +static const unsigned short normal_i2c[] = { 0x50, 0x51, 0x52, 0x53, 0x54, + 0x55, 0x56, 0x57, I2C_CLIENT_END }; + +/* Insmod parameters */ +I2C_CLIENT_INSMOD_1(eeprom); + + +/* Size of EEPROM in bytes */ +#define EEPROM_SIZE 256 + +/* possible types of eeprom devices */ +enum eeprom_nature { + UNKNOWN, + VAIO, +}; + +/* Each client has this additional data */ +struct eeprom_data { + struct mutex update_lock; + u8 valid; /* bitfield, bit!=0 if slice is valid */ + unsigned long last_updated[8]; /* In jiffies, 8 slices */ + u8 data[EEPROM_SIZE]; /* Register values */ + enum eeprom_nature nature; +}; + + +static void eeprom_update_client(struct i2c_client *client, u8 slice) +{ + struct eeprom_data *data = i2c_get_clientdata(client); + int i; + + mutex_lock(&data->update_lock); + + if (!(data->valid & (1 << slice)) || + time_after(jiffies, data->last_updated[slice] + 300 * HZ)) { + dev_dbg(&client->dev, "Starting eeprom update, slice %u\n", slice); + + if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { + for (i = slice << 5; i < (slice + 1) << 5; i += 32) + if (i2c_smbus_read_i2c_block_data(client, i, + 32, data->data + i) + != 32) + goto exit; + } else { + for (i = slice << 5; i < (slice + 1) << 5; i += 2) { + int word = i2c_smbus_read_word_data(client, i); + if (word < 0) + goto exit; + data->data[i] = word & 0xff; + data->data[i + 1] = word >> 8; + } + } + data->last_updated[slice] = jiffies; + data->valid |= (1 << slice); + } +exit: + mutex_unlock(&data->update_lock); +} + +static ssize_t eeprom_read(struct kobject *kobj, struct bin_attribute *bin_attr, + char *buf, loff_t off, size_t count) +{ + struct i2c_client *client = to_i2c_client(container_of(kobj, struct device, kobj)); + struct eeprom_data *data = i2c_get_clientdata(client); + u8 slice; + + if (off > EEPROM_SIZE) + return 0; + if (off + count > EEPROM_SIZE) + count = EEPROM_SIZE - off; + + /* Only refresh slices which contain requested bytes */ + for (slice = off >> 5; slice <= (off + count - 1) >> 5; slice++) + eeprom_update_client(client, slice); + + /* Hide Vaio private settings to regular users: + - BIOS passwords: bytes 0x00 to 0x0f + - UUID: bytes 0x10 to 0x1f + - Serial number: 0xc0 to 0xdf */ + if (data->nature == VAIO && !capable(CAP_SYS_ADMIN)) { + int i; + + for (i = 0; i < count; i++) { + if ((off + i <= 0x1f) || + (off + i >= 0xc0 && off + i <= 0xdf)) + buf[i] = 0; + else + buf[i] = data->data[off + i]; + } + } else { + memcpy(buf, &data->data[off], count); + } + + return count; +} + +static struct bin_attribute eeprom_attr = { + .attr = { + .name = "eeprom", + .mode = S_IRUGO, + }, + .size = EEPROM_SIZE, + .read = eeprom_read, +}; + +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int eeprom_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) +{ + struct i2c_adapter *adapter = client->adapter; + + /* EDID EEPROMs are often 24C00 EEPROMs, which answer to all + addresses 0x50-0x57, but we only care about 0x50. So decline + attaching to addresses >= 0x51 on DDC buses */ + if (!(adapter->class & I2C_CLASS_SPD) && client->addr >= 0x51) + return -ENODEV; + + /* There are four ways we can read the EEPROM data: + (1) I2C block reads (faster, but unsupported by most adapters) + (2) Word reads (128% overhead) + (3) Consecutive byte reads (88% overhead, unsafe) + (4) Regular byte data reads (265% overhead) + The third and fourth methods are not implemented by this driver + because all known adapters support one of the first two. */ + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_WORD_DATA) + && !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) + return -ENODEV; + + strlcpy(info->type, "eeprom", I2C_NAME_SIZE); + + return 0; +} + +static int eeprom_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adapter = client->adapter; + struct eeprom_data *data; + int err; + + if (!(data = kzalloc(sizeof(struct eeprom_data), GFP_KERNEL))) { + err = -ENOMEM; + goto exit; + } + + memset(data->data, 0xff, EEPROM_SIZE); + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + data->nature = UNKNOWN; + + /* Detect the Vaio nature of EEPROMs. + We use the "PCG-" or "VGN-" prefix as the signature. */ + if (client->addr == 0x57 + && i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA)) { + char name[4]; + + name[0] = i2c_smbus_read_byte_data(client, 0x80); + name[1] = i2c_smbus_read_byte_data(client, 0x81); + name[2] = i2c_smbus_read_byte_data(client, 0x82); + name[3] = i2c_smbus_read_byte_data(client, 0x83); + + if (!memcmp(name, "PCG-", 4) || !memcmp(name, "VGN-", 4)) { + dev_info(&client->dev, "Vaio EEPROM detected, " + "enabling privacy protection\n"); + data->nature = VAIO; + } + } + + /* create the sysfs eeprom file */ + err = sysfs_create_bin_file(&client->dev.kobj, &eeprom_attr); + if (err) + goto exit_kfree; + + return 0; + +exit_kfree: + kfree(data); +exit: + return err; +} + +static int eeprom_remove(struct i2c_client *client) +{ + sysfs_remove_bin_file(&client->dev.kobj, &eeprom_attr); + kfree(i2c_get_clientdata(client)); + + return 0; +} + +static const struct i2c_device_id eeprom_id[] = { + { "eeprom", 0 }, + { } +}; + +static struct i2c_driver eeprom_driver = { + .driver = { + .name = "eeprom", + }, + .probe = eeprom_probe, + .remove = eeprom_remove, + .id_table = eeprom_id, + + .class = I2C_CLASS_DDC | I2C_CLASS_SPD, + .detect = eeprom_detect, + .address_data = &addr_data, +}; + +static int __init eeprom_init(void) +{ + return i2c_add_driver(&eeprom_driver); +} + +static void __exit eeprom_exit(void) +{ + i2c_del_driver(&eeprom_driver); +} + + +MODULE_AUTHOR("Frodo Looijaard and " + "Philip Edelbrock and " + "Greg Kroah-Hartman "); +MODULE_DESCRIPTION("I2C EEPROM driver"); +MODULE_LICENSE("GPL"); + +module_init(eeprom_init); +module_exit(eeprom_exit); -- cgit v1.2.3-70-g09d2