From 619b08d45a40229040d6db8c9fb1f40b7e58b71f Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Fri, 15 Feb 2013 16:14:00 +0100 Subject: mmc: tmio: add support for the VccQ regulator Some SD/MMC interfaces use 2 power regulators: one to power the card itself (Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and UHS SD cards the regulators also have to be configured to supply different voltages. The preferred order of turning supply power on and off is to turn Vcc first on and last off. Signed-off-by: Guennadi Liakhovetski Signed-off-by: Chris Ball --- drivers/mmc/host/tmio_mmc_pio.c | 56 +++++++++++++++++++++++++++++++++-------- 1 file changed, 46 insertions(+), 10 deletions(-) (limited to 'drivers/mmc/host/tmio_mmc_pio.c') diff --git a/drivers/mmc/host/tmio_mmc_pio.c b/drivers/mmc/host/tmio_mmc_pio.c index e5b3fcf55c4..f508ecb5b8a 100644 --- a/drivers/mmc/host/tmio_mmc_pio.c +++ b/drivers/mmc/host/tmio_mmc_pio.c @@ -43,6 +43,7 @@ #include #include #include +#include #include #include #include @@ -155,6 +156,7 @@ static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock) host->set_clk_div(host->pdev, (clk>>22) & 1); sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, clk & 0x1ff); + msleep(10); } static void tmio_mmc_clk_stop(struct tmio_mmc_host *host) @@ -768,16 +770,48 @@ static int tmio_mmc_clk_update(struct mmc_host *mmc) return ret; } -static void tmio_mmc_set_power(struct tmio_mmc_host *host, struct mmc_ios *ios) +static void tmio_mmc_power_on(struct tmio_mmc_host *host, unsigned short vdd) { struct mmc_host *mmc = host->mmc; + int ret = 0; + + /* .set_ios() is returning void, so, no chance to report an error */ if (host->set_pwr) - host->set_pwr(host->pdev, ios->power_mode != MMC_POWER_OFF); + host->set_pwr(host->pdev, 1); + + if (!IS_ERR(mmc->supply.vmmc)) { + ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd); + /* + * Attention: empiric value. With a b43 WiFi SDIO card this + * delay proved necessary for reliable card-insertion probing. + * 100us were not enough. Is this the same 140us delay, as in + * tmio_mmc_set_ios()? + */ + udelay(200); + } + /* + * It seems, VccQ should be switched on after Vcc, this is also what the + * omap_hsmmc.c driver does. + */ + if (!IS_ERR(mmc->supply.vqmmc) && !ret) { + regulator_enable(mmc->supply.vqmmc); + udelay(200); + } +} + +static void tmio_mmc_power_off(struct tmio_mmc_host *host) +{ + struct mmc_host *mmc = host->mmc; + + if (!IS_ERR(mmc->supply.vqmmc)) + regulator_disable(mmc->supply.vqmmc); + if (!IS_ERR(mmc->supply.vmmc)) - /* Errors ignored... */ - mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, - ios->power_mode ? ios->vdd : 0); + mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0); + + if (host->set_pwr) + host->set_pwr(host->pdev, 0); } /* Set MMC clock / power. @@ -828,18 +862,20 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) if (!host->power) { tmio_mmc_clk_update(mmc); pm_runtime_get_sync(dev); - host->power = true; } tmio_mmc_set_clock(host, ios->clock); - /* power up SD bus */ - tmio_mmc_set_power(host, ios); + if (!host->power) { + /* power up SD card and the bus */ + tmio_mmc_power_on(host, ios->vdd); + host->power = true; + } /* start bus clock */ tmio_mmc_clk_start(host); } else if (ios->power_mode != MMC_POWER_UP) { - if (ios->power_mode == MMC_POWER_OFF) - tmio_mmc_set_power(host, ios); if (host->power) { struct tmio_mmc_data *pdata = host->pdata; + if (ios->power_mode == MMC_POWER_OFF) + tmio_mmc_power_off(host); tmio_mmc_clk_stop(host); host->power = false; pm_runtime_put(dev); -- cgit v1.2.3-70-g09d2