From e0aac5a289b1dacbc94bd9ae8c449bcdf9ab508c Mon Sep 17 00:00:00 2001 From: Auke Kok Date: Tue, 6 Mar 2007 08:57:21 -0800 Subject: e1000: FIX: be ready for incoming irq at pci_request_irq DEBUG_SHIRQ code exposed that e1000 was not ready for incoming interrupts after having called pci_request_irq. This obviously requires us to finish our software setup which assigns the irq handler before we request the irq. Signed-off-by: Auke Kok Signed-off-by: Jeff Garzik --- drivers/net/e1000/e1000_main.c | 66 ++++++++++++++++++++++++++++-------------- 1 file changed, 45 insertions(+), 21 deletions(-) (limited to 'drivers/net/e1000') diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index b28a915bd98..f777d37d8e6 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -522,14 +522,15 @@ e1000_release_manageability(struct e1000_adapter *adapter) } } -int -e1000_up(struct e1000_adapter *adapter) +/** + * e1000_configure - configure the hardware for RX and TX + * @adapter = private board structure + **/ +static void e1000_configure(struct e1000_adapter *adapter) { struct net_device *netdev = adapter->netdev; int i; - /* hardware has been reset, we need to reload some things */ - e1000_set_multi(netdev); e1000_restore_vlan(adapter); @@ -548,14 +549,20 @@ e1000_up(struct e1000_adapter *adapter) } adapter->tx_queue_len = netdev->tx_queue_len; +} + +int e1000_up(struct e1000_adapter *adapter) +{ + /* hardware has been reset, we need to reload some things */ + e1000_configure(adapter); + + clear_bit(__E1000_DOWN, &adapter->flags); #ifdef CONFIG_E1000_NAPI - netif_poll_enable(netdev); + netif_poll_enable(adapter->netdev); #endif e1000_irq_enable(adapter); - clear_bit(__E1000_DOWN, &adapter->flags); - /* fire a link change interrupt to start the watchdog */ E1000_WRITE_REG(&adapter->hw, ICS, E1000_ICS_LSC); return 0; @@ -640,15 +647,15 @@ e1000_down(struct e1000_adapter *adapter) * reschedule our watchdog timer */ set_bit(__E1000_DOWN, &adapter->flags); +#ifdef CONFIG_E1000_NAPI + netif_poll_disable(netdev); +#endif e1000_irq_disable(adapter); del_timer_sync(&adapter->tx_fifo_stall_timer); del_timer_sync(&adapter->watchdog_timer); del_timer_sync(&adapter->phy_info_timer); -#ifdef CONFIG_E1000_NAPI - netif_poll_disable(netdev); -#endif netdev->tx_queue_len = adapter->tx_queue_len; adapter->link_speed = 0; adapter->link_duplex = 0; @@ -1410,21 +1417,17 @@ e1000_open(struct net_device *netdev) return -EBUSY; /* allocate transmit descriptors */ - if ((err = e1000_setup_all_tx_resources(adapter))) + err = e1000_setup_all_tx_resources(adapter); + if (err) goto err_setup_tx; /* allocate receive descriptors */ - if ((err = e1000_setup_all_rx_resources(adapter))) - goto err_setup_rx; - - err = e1000_request_irq(adapter); + err = e1000_setup_all_rx_resources(adapter); if (err) - goto err_req_irq; + goto err_setup_rx; e1000_power_up_phy(adapter); - if ((err = e1000_up(adapter))) - goto err_up; adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; if ((adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) { @@ -1437,12 +1440,33 @@ e1000_open(struct net_device *netdev) e1000_check_mng_mode(&adapter->hw)) e1000_get_hw_control(adapter); + /* before we allocate an interrupt, we must be ready to handle it. + * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt + * as soon as we call pci_request_irq, so we have to setup our + * clean_rx handler before we do so. */ + e1000_configure(adapter); + + err = e1000_request_irq(adapter); + if (err) + goto err_req_irq; + + /* From here on the code is the same as e1000_up() */ + clear_bit(__E1000_DOWN, &adapter->flags); + +#ifdef CONFIG_E1000_NAPI + netif_poll_enable(netdev); +#endif + + e1000_irq_enable(adapter); + + /* fire a link status change interrupt to start the watchdog */ + E1000_WRITE_REG(&adapter->hw, ICS, E1000_ICS_LSC); + return E1000_SUCCESS; -err_up: - e1000_power_down_phy(adapter); - e1000_free_irq(adapter); err_req_irq: + e1000_release_hw_control(adapter); + e1000_power_down_phy(adapter); e1000_free_all_rx_resources(adapter); err_setup_rx: e1000_free_all_tx_resources(adapter); -- cgit v1.2.3-70-g09d2