From ce5eaf023a231ebd313ecc7e0b33278513d8ad80 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 18 Feb 2014 12:55:42 +0000 Subject: NET: fec: only enable napi if we are successful If napi is left enabled after a failed attempt to bring the interface up, we BUG: fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch libphy: PHY fixed-0:00 not found fec 2188000.ethernet eth0: could not attach to PHY ------------[ cut here ]------------ kernel BUG at include/linux/netdevice.h:502! Internal error: Oops - BUG: 0 [#1] SMP ARM ... PC is at fec_enet_open+0x4d0/0x500 LR is at __dev_open+0xa4/0xfc Only enable napi after we are past all the failure paths. Signed-off-by: Russell King Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet/freescale/fec_main.c') diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c index d4782b42401..903362a7b58 100644 --- a/drivers/net/ethernet/freescale/fec_main.c +++ b/drivers/net/ethernet/freescale/fec_main.c @@ -1778,8 +1778,6 @@ fec_enet_open(struct net_device *ndev) struct fec_enet_private *fep = netdev_priv(ndev); int ret; - napi_enable(&fep->napi); - /* I should reset the ring buffers here, but I don't yet know * a simple way to do that. */ @@ -1794,6 +1792,8 @@ fec_enet_open(struct net_device *ndev) fec_enet_free_buffers(ndev); return ret; } + + napi_enable(&fep->napi); phy_start(fep->phy_dev); netif_start_queue(ndev); fep->opened = 1; -- cgit v1.2.3-70-g09d2 From fb8ef788680d48523321e5f150b23700a1caf980 Mon Sep 17 00:00:00 2001 From: Duan Fugang-B38611 Date: Thu, 20 Feb 2014 18:14:39 +0800 Subject: net: fec: fix potential issue to avoid fec interrupt lost and crc error The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to enable tx interrupt generation and crc checksum. There has potential issue like as: CPU fec uDMA Set tx ready bit uDMA start the BD transmission Set "INT" bit Set "PINS" bit ... Above situation cause fec tx interrupt lost and fec MAC don't do CRC checksum. The patch fix the potential issue. Signed-off-by: Fugang Duan Acked-by: Frank Li Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec_main.c | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-) (limited to 'drivers/net/ethernet/freescale/fec_main.c') diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c index 903362a7b58..479a7cba45c 100644 --- a/drivers/net/ethernet/freescale/fec_main.c +++ b/drivers/net/ethernet/freescale/fec_main.c @@ -389,12 +389,6 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *ndev) netdev_err(ndev, "Tx DMA memory map failed\n"); return NETDEV_TX_OK; } - /* Send it on its way. Tell FEC it's ready, interrupt when done, - * it's the last BD of the frame, and to put the CRC on the end. - */ - status |= (BD_ENET_TX_READY | BD_ENET_TX_INTR - | BD_ENET_TX_LAST | BD_ENET_TX_TC); - bdp->cbd_sc = status; if (fep->bufdesc_ex) { @@ -416,6 +410,13 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *ndev) } } + /* Send it on its way. Tell FEC it's ready, interrupt when done, + * it's the last BD of the frame, and to put the CRC on the end. + */ + status |= (BD_ENET_TX_READY | BD_ENET_TX_INTR + | BD_ENET_TX_LAST | BD_ENET_TX_TC); + bdp->cbd_sc = status; + bdp_pre = fec_enet_get_prevdesc(bdp, fep); if ((id_entry->driver_data & FEC_QUIRK_ERR006358) && !(bdp_pre->cbd_sc & BD_ENET_TX_READY)) { -- cgit v1.2.3-70-g09d2