From af901ca181d92aac3a7dc265144a9081a86d8f39 Mon Sep 17 00:00:00 2001 From: André Goddard Rosa Date: Sat, 14 Nov 2009 13:09:05 -0200 Subject: tree-wide: fix assorted typos all over the place MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit That is "success", "unknown", "through", "performance", "[re|un]mapping" , "access", "default", "reasonable", "[con]currently", "temperature" , "channel", "[un]used", "application", "example","hierarchy", "therefore" , "[over|under]flow", "contiguous", "threshold", "enough" and others. Signed-off-by: André Goddard Rosa Signed-off-by: Jiri Kosina --- drivers/net/wireless/ath/ath5k/phy.c | 6 +++--- drivers/net/wireless/ath/ath9k/rc.c | 2 +- 2 files changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers/net/wireless/ath') diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c index 1a039f2bd73..6f04cc758dc 100644 --- a/drivers/net/wireless/ath/ath5k/phy.c +++ b/drivers/net/wireless/ath/ath5k/phy.c @@ -117,7 +117,7 @@ static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah, /* * This code is used to optimize rf gain on different environments - * (temprature mostly) based on feedback from a power detector. + * (temperature mostly) based on feedback from a power detector. * * It's only used on RF5111 and RF5112, later RF chips seem to have * auto adjustment on hw -notice they have a much smaller BANK 7 and @@ -2675,7 +2675,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, /* Fill curves in reverse order * from lower power (max gain) * to higher power. Use curve -> idx - * backmaping we did on eeprom init */ + * backmapping we did on eeprom init */ u8 idx = pdg_curve_to_idx[pdg]; /* Grab the needed curves by index */ @@ -2777,7 +2777,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, /* Now we have a set of curves for this * channel on tmpL (x range is table_max - table_min * and y values are tmpL[pdg][]) sorted in the same - * order as EEPROM (because we've used the backmaping). + * order as EEPROM (because we've used the backmapping). * So for RF5112 it's from higher power to lower power * and for RF2413 it's from lower power to higher power. * For RF5111 we only have one curve. */ diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c index 1895d63aad0..0a35ee62a02 100644 --- a/drivers/net/wireless/ath/ath9k/rc.c +++ b/drivers/net/wireless/ath/ath9k/rc.c @@ -969,7 +969,7 @@ static bool ath_rc_update_per(struct ath_softc *sc, * Since this probe succeeded, we allow the next * probe twice as soon. This allows the maxRate * to move up faster if the probes are - * succesful. + * successful. */ ath_rc_priv->probe_time = now_msec - rate_table->probe_interval / 2; -- cgit v1.2.3-70-g09d2