From 0d8877a10d65f3c9bb84ad150e524d95ebd377fb Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Fri, 17 May 2013 10:36:29 +0200 Subject: iwlwifi: move some configuration parameters into DVM There are a number of parameters that aren't really hardware specific but rather define how the DVM firmware is used. Move these into the DVM configuration. Reviewed-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/iwl-config.h | 43 +------------------------------ 1 file changed, 1 insertion(+), 42 deletions(-) (limited to 'drivers/net/wireless/iwlwifi/iwl-config.h') diff --git a/drivers/net/wireless/iwlwifi/iwl-config.h b/drivers/net/wireless/iwlwifi/iwl-config.h index c3c9268affa..a193832fc79 100644 --- a/drivers/net/wireless/iwlwifi/iwl-config.h +++ b/drivers/net/wireless/iwlwifi/iwl-config.h @@ -136,17 +136,9 @@ enum iwl_led_mode { * @led_compensation: compensate on the led on/off time per HW according * to the deviation to achieve the desired led frequency. * The detail algorithm is described in iwl-led.c - * @chain_noise_num_beacons: number of beacons used to compute chain noise - * @adv_thermal_throttle: support advance thermal throttle - * @support_ct_kill_exit: support ct kill exit condition - * @plcp_delta_threshold: plcp error rate threshold used to trigger - * radio tuning when there is a high receiving plcp error rate - * @chain_noise_scale: default chain noise scale used for gain computation * @wd_timeout: TX queues watchdog timeout * @max_event_log_size: size of event log buffer size for ucode event logging * @shadow_reg_enable: HW shadow register support - * @hd_v2: v2 of enhanced sensitivity value, used for 2000 series and up - * @no_idle_support: do not support idle mode */ struct iwl_base_params { int eeprom_size; @@ -157,31 +149,9 @@ struct iwl_base_params { const u16 max_ll_items; const bool shadow_ram_support; u16 led_compensation; - bool adv_thermal_throttle; - bool support_ct_kill_exit; - u8 plcp_delta_threshold; - s32 chain_noise_scale; unsigned int wd_timeout; u32 max_event_log_size; const bool shadow_reg_enable; - const bool hd_v2; - const bool no_idle_support; -}; - -/* - * @advanced_bt_coexist: support advanced bt coexist - * @bt_init_traffic_load: specify initial bt traffic load - * @bt_prio_boost: default bt priority boost value - * @agg_time_limit: maximum number of uSec in aggregation - * @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode - */ -struct iwl_bt_params { - bool advanced_bt_coexist; - u8 bt_init_traffic_load; - u32 bt_prio_boost; - u16 agg_time_limit; - bool bt_sco_disable; - bool bt_session_2; }; /* @@ -231,16 +201,10 @@ struct iwl_eeprom_params { * @nvm_calib_ver: NVM calibration version * @lib: pointer to the lib ops * @base_params: pointer to basic parameters - * @ht_params: point to ht patameters - * @bt_params: pointer to bt parameters - * @need_temp_offset_calib: need to perform temperature offset calibration - * @no_xtal_calib: some devices do not need crystal calibration data, - * don't send it to those + * @ht_params: point to ht parameters * @led_mode: 0=blinking, 1=On(RF On)/Off(RF Off) - * @adv_pm: advance power management * @rx_with_siso_diversity: 1x1 device with rx antenna diversity * @internal_wimax_coex: internal wifi/wimax combo device - * @temp_offset_v2: support v2 of temperature offset calibration * * We enable the driver to be backward compatible wrt. hardware features. * API differences in uCode shouldn't be handled here but through TLVs @@ -264,15 +228,10 @@ struct iwl_cfg { const struct iwl_base_params *base_params; /* params likely to change within a device family */ const struct iwl_ht_params *ht_params; - const struct iwl_bt_params *bt_params; const struct iwl_eeprom_params *eeprom_params; - const bool need_temp_offset_calib; /* if used set to true */ - const bool no_xtal_calib; enum iwl_led_mode led_mode; - const bool adv_pm; const bool rx_with_siso_diversity; const bool internal_wimax_coex; - const bool temp_offset_v2; }; /* -- cgit v1.2.3-70-g09d2