From 1862cdd542025218f7a390b7e6ddc83a1362d1e0 Mon Sep 17 00:00:00 2001 From: Ionut Nicu Date: Mon, 11 Jul 2011 16:46:12 +0300 Subject: USB: ftdi_sio: fix minor typo in get_ftdi_divisor Even if it's unlikely for this to cause an error, there is a typo in the code that uses the bitwise-AND operator instead of the logical one. Signed-off-by: Ionut Nicu Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb/serial/ftdi_sio.c') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 2e06b90aa1f..9afb3614373 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -1171,7 +1171,7 @@ static __u32 get_ftdi_divisor(struct tty_struct *tty, case FT2232H: /* FT2232H chip */ case FT4232H: /* FT4232H chip */ case FT232H: /* FT232H chip */ - if ((baud <= 12000000) & (baud >= 1200)) { + if ((baud <= 12000000) && (baud >= 1200)) { div_value = ftdi_2232h_baud_to_divisor(baud); } else if (baud < 1200) { div_value = ftdi_232bm_baud_to_divisor(baud); -- cgit v1.2.3-70-g09d2 From 0ee404ccf1c63aa25363940d474c3c03f8d7e882 Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Fri, 22 Jul 2011 10:41:15 +0200 Subject: usb: serial: ftdi_sio.c: For the FT232H FTDI_SIO_SET_BAUDRATE_REQUEST, index needs to be shifted too the recent addition of the FT232H showed that baudrate was set wrong. See gmane.linux.usb.general: "[ftdi_sio] FT232H support". With the old code, the MSB of the 4 encoded fractional divider bits and more important the clock predivider bits got lost. Adding the FT232H to the code patch were these bits are shifted solves the problem. I verified baud rates with a scope now. I suspect, that the BM device probably needs these bits shifted too. But there is no predivider bit, so this is not obvious, and a missing MSB of the encoded fractional divider only shifts the resulting baudrate minimal. The AM has only 3 bits of encoded fractional divider, so it is not impacted. I have no BM device to test, so I only added a comment and left the code for the BM untouched. Signed-off-by: Uwe Bonnes Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers/usb/serial/ftdi_sio.c') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 9afb3614373..7d42f61bd7a 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -1205,7 +1205,10 @@ static int change_speed(struct tty_struct *tty, struct usb_serial_port *port) urb_index_value = get_ftdi_divisor(tty, port); urb_value = (__u16)urb_index_value; urb_index = (__u16)(urb_index_value >> 16); - if (priv->interface) { /* FT2232C */ + if ((priv->chip_type == FT2232C) || (priv->chip_type == FT2232H) || + (priv->chip_type == FT4232H) || (priv->chip_type == FT232H)) { + /* Probably the BM type needs the MSB of the encoded fractional + * divider also moved like for the chips above. Any infos? */ urb_index = (__u16)((urb_index << 8) | priv->interface); } -- cgit v1.2.3-70-g09d2 From ce7e9065958191e6b7ca49d7ed0e1099c486d198 Mon Sep 17 00:00:00 2001 From: Artur Zimmer Date: Wed, 10 Aug 2011 03:51:28 +0200 Subject: USB: Serial: Add PID(0xF7C0) to FTDI SIO driver for a zeitcontrol-device Here is a patch for a new PID (zeitcontrol-device mifare-reader FT232BL(like FT232BM but lead free)). Signed-off-by: Artur Zimmer Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio_ids.h | 6 +++++- 2 files changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/usb/serial/ftdi_sio.c') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 7d42f61bd7a..78a2cf9551c 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -151,6 +151,7 @@ static struct ftdi_sio_quirk ftdi_stmclite_quirk = { * /sys/bus/usb/ftdi_sio/new_id, then send patch/report! */ static struct usb_device_id id_table_combined [] = { + { USB_DEVICE(FTDI_VID, FTDI_ZEITCONTROL_TAGTRACE_MIFARE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CTI_MINI_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CTI_NANO_PID) }, { USB_DEVICE(FTDI_VID, FTDI_AMC232_PID) }, diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index 19156d1049f..bf5227ad3ef 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -1159,4 +1159,8 @@ /* USB-Nano-485*/ #define FTDI_CTI_NANO_PID 0xF60B - +/* + * ZeitControl cardsystems GmbH rfid-readers http://zeitconrol.de + */ +/* TagTracer MIFARE*/ +#define FTDI_ZEITCONTROL_TAGTRACE_MIFARE_PID 0xF7C0 -- cgit v1.2.3-70-g09d2 From c96fbdd0ab97235f930ebf24b38fa42a2e3458cf Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Thu, 25 Aug 2011 11:46:58 +0200 Subject: USB: ftdi_sio: add Calao reference board support Calao use on there dev kits a FT2232 where the port 0 is used for the JTAG and port 1 for the UART They use the same VID and PID as FTDI Chip but they program the manufacturer name in the eeprom So use this information to detect it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Cc: Gregory Hermant Cc: Alan Cox Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 20 +++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-) (limited to 'drivers/usb/serial/ftdi_sio.c') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 78a2cf9551c..5fc13e71791 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -101,6 +101,7 @@ static int ftdi_jtag_probe(struct usb_serial *serial); static int ftdi_mtxorb_hack_setup(struct usb_serial *serial); static int ftdi_NDI_device_setup(struct usb_serial *serial); static int ftdi_stmclite_probe(struct usb_serial *serial); +static int ftdi_8u2232c_probe(struct usb_serial *serial); static void ftdi_USB_UIRT_setup(struct ftdi_private *priv); static void ftdi_HE_TIRA1_setup(struct ftdi_private *priv); @@ -128,6 +129,10 @@ static struct ftdi_sio_quirk ftdi_stmclite_quirk = { .probe = ftdi_stmclite_probe, }; +static struct ftdi_sio_quirk ftdi_8u2232c_quirk = { + .probe = ftdi_8u2232c_probe, +}; + /* * The 8U232AM has the same API as the sio except for: * - it can support MUCH higher baudrates; up to: @@ -178,7 +183,8 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_8U232AM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) }, { USB_DEVICE(FTDI_VID, FTDI_232RL_PID) }, - { USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) , + .driver_info = (kernel_ulong_t)&ftdi_8u2232c_quirk }, { USB_DEVICE(FTDI_VID, FTDI_4232H_PID) }, { USB_DEVICE(FTDI_VID, FTDI_232H_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MICRO_CHAMELEON_PID) }, @@ -1737,6 +1743,18 @@ static int ftdi_jtag_probe(struct usb_serial *serial) return 0; } +static int ftdi_8u2232c_probe(struct usb_serial *serial) +{ + struct usb_device *udev = serial->dev; + + dbg("%s", __func__); + + if (strcmp(udev->manufacturer, "CALAO Systems") == 0) + return ftdi_jtag_probe(serial); + + return 0; +} + /* * First and second port on STMCLiteadaptors is reserved for JTAG interface * and the forth port for pio -- cgit v1.2.3-70-g09d2