From 00d340b94f6df17d5dc478521e4ee1cfb30c53ac Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Wed, 1 Feb 2006 03:06:54 -0800 Subject: [PATCH] i810fb: Do not probe the third i2c bus by default Some time before 2.6.15, a third DDC channel was added to i810fb. On systems where these ddc pins are not connected, the probe takes about 10 seconds. Add a boot/module option for i810fb to explicitly probe for the 3rd ddc bus if needed. Signed-off-by: Antonino Daplas Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/i810/i810-i2c.c | 6 +++--- drivers/video/i810/i810.h | 1 + drivers/video/i810/i810_main.c | 13 ++++++++++--- 3 files changed, 14 insertions(+), 6 deletions(-) (limited to 'drivers/video/i810') diff --git a/drivers/video/i810/i810-i2c.c b/drivers/video/i810/i810-i2c.c index bd410e06db7..e3c8b5f1ca7 100644 --- a/drivers/video/i810/i810-i2c.c +++ b/drivers/video/i810/i810-i2c.c @@ -191,11 +191,11 @@ int i810_probe_i2c_connector(struct fb_info *info, u8 **out_edid, int conn) u8 *edid = NULL; int i; - DPRINTK("i810-i2c: Probe DDC%i Bus\n", conn); - if (conn < 4) { + DPRINTK("i810-i2c: Probe DDC%i Bus\n", conn+1); + if (conn < par->ddc_num) { for (i = 0; i < 3; i++) { /* Do the real work */ - edid = i810_do_probe_i2c_edid(&par->chan[conn-1]); + edid = i810_do_probe_i2c_edid(&par->chan[conn]); if (edid) break; } diff --git a/drivers/video/i810/i810.h b/drivers/video/i810/i810.h index 6c187d5fe95..579195c2bea 100644 --- a/drivers/video/i810/i810.h +++ b/drivers/video/i810/i810.h @@ -280,6 +280,7 @@ struct i810fb_par { u32 blit_bpp; u32 ovract; u32 cur_state; + u32 ddc_num; int mtrr_reg; u16 bltcntl; u8 interlace; diff --git a/drivers/video/i810/i810_main.c b/drivers/video/i810/i810_main.c index 266d0ab9266..d8467c03b49 100644 --- a/drivers/video/i810/i810_main.c +++ b/drivers/video/i810/i810_main.c @@ -149,6 +149,7 @@ static int vyres __devinitdata; static int sync __devinitdata; static int extvga __devinitdata; static int dcolor __devinitdata; +static int ddc3 __devinitdata = 2; /*------------------------------------------------------------*/ @@ -1763,6 +1764,8 @@ static void __devinit i810_init_defaults(struct i810fb_par *par, if (sync) par->dev_flags |= ALWAYS_SYNC; + par->ddc_num = ddc3; + if (bpp < 8) bpp = 8; @@ -1885,7 +1888,7 @@ static void __devinit i810fb_find_init_mode(struct fb_info *info) int found = 0; #ifdef CONFIG_FB_I810_I2C int i; - int err; + int err = 1; struct i810fb_par *par = info->par; #endif @@ -1895,8 +1898,8 @@ static void __devinit i810fb_find_init_mode(struct fb_info *info) #ifdef CONFIG_FB_I810_I2C i810_create_i2c_busses(par); - for (i = 0; i < 4; i++) { - err = i810_probe_i2c_connector(info, &par->edid, i+1); + for (i = 0; i < par->ddc_num + 1; i++) { + err = i810_probe_i2c_connector(info, &par->edid, i); if (!err) break; } @@ -1983,6 +1986,8 @@ static int __devinit i810fb_setup(char *options) vsync2 = simple_strtoul(this_opt+7, NULL, 0); else if (!strncmp(this_opt, "dcolor", 6)) dcolor = 1; + else if (!strncmp(this_opt, "ddc3", 4)) + ddc3 = 3; else mode_option = this_opt; } @@ -2190,6 +2195,8 @@ MODULE_PARM_DESC(sync, "wait for accel engine to finish drawing" module_param(dcolor, bool, 0); MODULE_PARM_DESC(dcolor, "use DirectColor visuals" " (default = 0 = TrueColor)"); +module_param(ddc3, bool, 0); +MODULE_PARM_DESC(ddc3, "Probe DDC bus 3 (default = 0 = no)"); module_param(mode_option, charp, 0); MODULE_PARM_DESC(mode_option, "Specify initial video mode"); -- cgit v1.2.3-70-g09d2