From c653e6351e371b33b29871e5eedf610ffb3be037 Mon Sep 17 00:00:00 2001 From: Auke Kok Date: Tue, 23 May 2006 13:35:57 -0700 Subject: e1000: add shutdown handler back to fix WOL Someone was waaay too aggressive and removed e1000's reboot notifier instead of porting it to the new way of the shutdown handler. This change broke wake on lan. Add the shutdown handler back in using the same method as e100 uses. Signed-off-by: Jesse Brandeburg Signed-off-by: Auke Kok --- drivers/net/e1000/e1000_main.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index fb8cef61914..df819c1275a 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -221,6 +221,7 @@ static void e1000_restore_vlan(struct e1000_adapter *adapter); static int e1000_suspend(struct pci_dev *pdev, pm_message_t state); static int e1000_resume(struct pci_dev *pdev); #endif +static void e1000_shutdown(struct pci_dev *pdev); #ifdef CONFIG_NET_POLL_CONTROLLER /* for netdump / net console */ @@ -236,8 +237,9 @@ static struct pci_driver e1000_driver = { /* Power Managment Hooks */ #ifdef CONFIG_PM .suspend = e1000_suspend, - .resume = e1000_resume + .resume = e1000_resume, #endif + .shutdown = e1000_shutdown }; MODULE_AUTHOR("Intel Corporation, "); @@ -4605,6 +4607,12 @@ e1000_resume(struct pci_dev *pdev) return 0; } #endif + +static void e1000_shutdown(struct pci_dev *pdev) +{ + e1000_suspend(pdev, PMSG_SUSPEND); +} + #ifdef CONFIG_NET_POLL_CONTROLLER /* * Polling 'interrupt' - used by things like netconsole to send skbs -- cgit v1.2.3-70-g09d2 From a42a507cd3af14a2696b7c020996e48c10bf7742 Mon Sep 17 00:00:00 2001 From: Auke Kok Date: Tue, 23 May 2006 13:36:01 -0700 Subject: e1000: remove backslash r debug printfs This removes unwanted characters in the debug output that should have never been there. Signed-off-by: Auke Kok --- drivers/net/e1000/e1000_hw.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c index 4c796e54b84..2e211df1698 100644 --- a/drivers/net/e1000/e1000_hw.c +++ b/drivers/net/e1000/e1000_hw.c @@ -2493,10 +2493,10 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) */ if(hw->original_fc == e1000_fc_full) { hw->fc = e1000_fc_full; - DEBUGOUT("Flow Control = FULL.\r\n"); + DEBUGOUT("Flow Control = FULL.\n"); } else { hw->fc = e1000_fc_rx_pause; - DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n"); + DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); } } /* For receiving PAUSE frames ONLY. @@ -2512,7 +2512,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { hw->fc = e1000_fc_tx_pause; - DEBUGOUT("Flow Control = TX PAUSE frames only.\r\n"); + DEBUGOUT("Flow Control = TX PAUSE frames only.\n"); } /* For transmitting PAUSE frames ONLY. * @@ -2527,7 +2527,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { hw->fc = e1000_fc_rx_pause; - DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n"); + DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); } /* Per the IEEE spec, at this point flow control should be * disabled. However, we want to consider that we could @@ -2553,10 +2553,10 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) hw->original_fc == e1000_fc_tx_pause) || hw->fc_strict_ieee) { hw->fc = e1000_fc_none; - DEBUGOUT("Flow Control = NONE.\r\n"); + DEBUGOUT("Flow Control = NONE.\n"); } else { hw->fc = e1000_fc_rx_pause; - DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n"); + DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); } /* Now we need to do one last check... If we auto- @@ -2581,7 +2581,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) return ret_val; } } else { - DEBUGOUT("Copper PHY and Auto Neg has not completed.\r\n"); + DEBUGOUT("Copper PHY and Auto Neg has not completed.\n"); } } return E1000_SUCCESS; @@ -2764,7 +2764,7 @@ e1000_check_for_link(struct e1000_hw *hw) hw->autoneg_failed = 1; return 0; } - DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n"); + DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); /* Disable auto-negotiation in the TXCW register */ E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE)); @@ -2789,7 +2789,7 @@ e1000_check_for_link(struct e1000_hw *hw) else if(((hw->media_type == e1000_media_type_fiber) || (hw->media_type == e1000_media_type_internal_serdes)) && (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { - DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\r\n"); + DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); E1000_WRITE_REG(hw, TXCW, hw->txcw); E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU)); @@ -2852,13 +2852,13 @@ e1000_get_speed_and_duplex(struct e1000_hw *hw, if(status & E1000_STATUS_FD) { *duplex = FULL_DUPLEX; - DEBUGOUT("Full Duplex\r\n"); + DEBUGOUT("Full Duplex\n"); } else { *duplex = HALF_DUPLEX; - DEBUGOUT(" Half Duplex\r\n"); + DEBUGOUT(" Half Duplex\n"); } } else { - DEBUGOUT("1000 Mbs, Full Duplex\r\n"); + DEBUGOUT("1000 Mbs, Full Duplex\n"); *speed = SPEED_1000; *duplex = FULL_DUPLEX; } -- cgit v1.2.3-70-g09d2 From 76c224bc9fdf108ae6e97553322122f53bdbe75c Mon Sep 17 00:00:00 2001 From: Auke Kok Date: Tue, 23 May 2006 13:36:06 -0700 Subject: e1000: remove leading and trailing whitespace. Some leading and trailing whitespace made it into the driver code here. Signed-off-by: Auke Kok --- drivers/net/e1000/e1000_ethtool.c | 44 ++++++++++---------- drivers/net/e1000/e1000_hw.c | 88 +++++++++++++++++++-------------------- drivers/net/e1000/e1000_hw.h | 4 +- drivers/net/e1000/e1000_main.c | 26 ++++++------ 4 files changed, 81 insertions(+), 81 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c index e48dc578fde..cfdf0b24ffc 100644 --- a/drivers/net/e1000/e1000_ethtool.c +++ b/drivers/net/e1000/e1000_ethtool.c @@ -865,15 +865,15 @@ static int e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data) { struct net_device *netdev = adapter->netdev; - uint32_t mask, i=0, shared_int = TRUE; - uint32_t irq = adapter->pdev->irq; + uint32_t mask, i=0, shared_int = TRUE; + uint32_t irq = adapter->pdev->irq; *data = 0; /* Hook up test interrupt handler just for this test */ - if (!request_irq(irq, &e1000_test_intr, 0, netdev->name, netdev)) { - shared_int = FALSE; - } else if (request_irq(irq, &e1000_test_intr, SA_SHIRQ, + if (!request_irq(irq, &e1000_test_intr, 0, netdev->name, netdev)) { + shared_int = FALSE; + } else if (request_irq(irq, &e1000_test_intr, SA_SHIRQ, netdev->name, netdev)){ *data = 1; return -1; @@ -889,22 +889,22 @@ e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data) /* Interrupt to test */ mask = 1 << i; - if (!shared_int) { - /* Disable the interrupt to be reported in - * the cause register and then force the same - * interrupt and see if one gets posted. If - * an interrupt was posted to the bus, the - * test failed. - */ - adapter->test_icr = 0; - E1000_WRITE_REG(&adapter->hw, IMC, mask); - E1000_WRITE_REG(&adapter->hw, ICS, mask); - msec_delay(10); - - if (adapter->test_icr & mask) { - *data = 3; - break; - } + if (!shared_int) { + /* Disable the interrupt to be reported in + * the cause register and then force the same + * interrupt and see if one gets posted. If + * an interrupt was posted to the bus, the + * test failed. + */ + adapter->test_icr = 0; + E1000_WRITE_REG(&adapter->hw, IMC, mask); + E1000_WRITE_REG(&adapter->hw, ICS, mask); + msec_delay(10); + + if (adapter->test_icr & mask) { + *data = 3; + break; + } } /* Enable the interrupt to be reported in @@ -923,7 +923,7 @@ e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data) break; } - if (!shared_int) { + if (!shared_int) { /* Disable the other interrupts to be reported in * the cause register and then force the other * interrupts and see if any get posted. If diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c index 2e211df1698..3959039b16e 100644 --- a/drivers/net/e1000/e1000_hw.c +++ b/drivers/net/e1000/e1000_hw.c @@ -765,7 +765,7 @@ e1000_init_hw(struct e1000_hw *hw) } if (hw->mac_type == e1000_82573) { - e1000_enable_tx_pkt_filtering(hw); + e1000_enable_tx_pkt_filtering(hw); } switch (hw->mac_type) { @@ -861,7 +861,7 @@ e1000_adjust_serdes_amplitude(struct e1000_hw *hw) if(eeprom_data != EEPROM_RESERVED_WORD) { /* Adjust SERDES output amplitude only. */ - eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK; + eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK; ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data); if(ret_val) return ret_val; @@ -1228,7 +1228,7 @@ e1000_copper_link_igp_setup(struct e1000_hw *hw) if (hw->phy_reset_disable) return E1000_SUCCESS; - + ret_val = e1000_phy_reset(hw); if (ret_val) { DEBUGOUT("Error Resetting the PHY\n"); @@ -1370,7 +1370,7 @@ e1000_copper_link_ggp_setup(struct e1000_hw *hw) DEBUGFUNC("e1000_copper_link_ggp_setup"); if(!hw->phy_reset_disable) { - + /* Enable CRS on TX for half-duplex operation. */ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); @@ -1519,7 +1519,7 @@ e1000_copper_link_mgp_setup(struct e1000_hw *hw) if(hw->phy_reset_disable) return E1000_SUCCESS; - + /* Enable CRS on TX. This must be set for half-duplex operation. */ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); if(ret_val) @@ -1665,7 +1665,7 @@ e1000_copper_link_autoneg(struct e1000_hw *hw) * collision distance in the Transmit Control Register. * 2) Set up flow control on the MAC to that established with * the link partner. -* 3) Config DSP to improve Gigabit link quality for some PHY revisions. +* 3) Config DSP to improve Gigabit link quality for some PHY revisions. * * hw - Struct containing variables accessed by shared code ******************************************************************************/ @@ -1674,7 +1674,7 @@ e1000_copper_link_postconfig(struct e1000_hw *hw) { int32_t ret_val; DEBUGFUNC("e1000_copper_link_postconfig"); - + if(hw->mac_type >= e1000_82544) { e1000_config_collision_dist(hw); } else { @@ -1698,7 +1698,7 @@ e1000_copper_link_postconfig(struct e1000_hw *hw) return ret_val; } } - + return E1000_SUCCESS; } @@ -1754,11 +1754,11 @@ e1000_setup_copper_link(struct e1000_hw *hw) } if(hw->autoneg) { - /* Setup autoneg and flow control advertisement - * and perform autonegotiation */ + /* Setup autoneg and flow control advertisement + * and perform autonegotiation */ ret_val = e1000_copper_link_autoneg(hw); if(ret_val) - return ret_val; + return ret_val; } else { /* PHY will be set to 10H, 10F, 100H,or 100F * depending on value from forced_speed_duplex. */ @@ -1786,7 +1786,7 @@ e1000_setup_copper_link(struct e1000_hw *hw) ret_val = e1000_copper_link_postconfig(hw); if(ret_val) return ret_val; - + DEBUGOUT("Valid link established!!!\n"); return E1000_SUCCESS; } @@ -1984,7 +1984,7 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw) DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); - ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg); + ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg); if(ret_val) return ret_val; @@ -2273,7 +2273,7 @@ e1000_config_mac_to_phy(struct e1000_hw *hw) DEBUGFUNC("e1000_config_mac_to_phy"); - /* 82544 or newer MAC, Auto Speed Detection takes care of + /* 82544 or newer MAC, Auto Speed Detection takes care of * MAC speed/duplex configuration.*/ if (hw->mac_type >= e1000_82544) return E1000_SUCCESS; @@ -2292,9 +2292,9 @@ e1000_config_mac_to_phy(struct e1000_hw *hw) if(ret_val) return ret_val; - if(phy_data & M88E1000_PSSR_DPLX) + if(phy_data & M88E1000_PSSR_DPLX) ctrl |= E1000_CTRL_FD; - else + else ctrl &= ~E1000_CTRL_FD; e1000_config_collision_dist(hw); @@ -2884,7 +2884,7 @@ e1000_get_speed_and_duplex(struct e1000_hw *hw, } } - if ((hw->mac_type == e1000_80003es2lan) && + if ((hw->mac_type == e1000_80003es2lan) && (hw->media_type == e1000_media_type_copper)) { if (*speed == SPEED_1000) ret_val = e1000_configure_kmrn_for_1000(hw); @@ -3160,7 +3160,7 @@ e1000_read_phy_reg(struct e1000_hw *hw, if (e1000_swfw_sync_acquire(hw, swfw)) return -E1000_ERR_SWFW_SYNC; - if((hw->phy_type == e1000_phy_igp || + if((hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) && (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, @@ -3299,7 +3299,7 @@ e1000_write_phy_reg(struct e1000_hw *hw, if (e1000_swfw_sync_acquire(hw, swfw)) return -E1000_ERR_SWFW_SYNC; - if((hw->phy_type == e1000_phy_igp || + if((hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) && (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, @@ -3497,22 +3497,22 @@ e1000_phy_hw_reset(struct e1000_hw *hw) } /* Read the device control register and assert the E1000_CTRL_PHY_RST * bit. Then, take it out of reset. - * For pre-e1000_82571 hardware, we delay for 10ms between the assert + * For pre-e1000_82571 hardware, we delay for 10ms between the assert * and deassert. For e1000_82571 hardware and later, we instead delay * for 50us between and 10ms after the deassertion. */ ctrl = E1000_READ_REG(hw, CTRL); E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST); E1000_WRITE_FLUSH(hw); - - if (hw->mac_type < e1000_82571) + + if (hw->mac_type < e1000_82571) msec_delay(10); else udelay(100); - + E1000_WRITE_REG(hw, CTRL, ctrl); E1000_WRITE_FLUSH(hw); - + if (hw->mac_type >= e1000_82571) msec_delay(10); e1000_swfw_sync_release(hw, swfw); @@ -3816,7 +3816,7 @@ e1000_phy_m88_get_info(struct e1000_hw *hw, /* Check polarity status */ ret_val = e1000_check_polarity(hw, &polarity); if(ret_val) - return ret_val; + return ret_val; phy_info->cable_polarity = polarity; ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); @@ -4541,14 +4541,14 @@ e1000_read_eeprom_eerd(struct e1000_hw *hw, E1000_WRITE_REG(hw, EERD, eerd); error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ); - + if(error) { break; } data[i] = (E1000_READ_REG(hw, EERD) >> E1000_EEPROM_RW_REG_DATA); - + } - + return error; } @@ -4574,24 +4574,24 @@ e1000_write_eeprom_eewr(struct e1000_hw *hw, return -E1000_ERR_SWFW_SYNC; for (i = 0; i < words; i++) { - register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) | - ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) | + register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) | + ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) | E1000_EEPROM_RW_REG_START; error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE); if(error) { break; - } + } E1000_WRITE_REG(hw, EEWR, register_value); - + error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE); - + if(error) { break; - } + } } - + e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); return error; } @@ -4611,7 +4611,7 @@ e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd) for(i = 0; i < attempts; i++) { if(eerd == E1000_EEPROM_POLL_READ) reg = E1000_READ_REG(hw, EERD); - else + else reg = E1000_READ_REG(hw, EEWR); if(reg & E1000_EEPROM_RW_REG_DONE) { @@ -5136,7 +5136,7 @@ e1000_mc_addr_list_update(struct e1000_hw *hw, uint32_t i; uint32_t num_rar_entry; uint32_t num_mta_entry; - + DEBUGFUNC("e1000_mc_addr_list_update"); /* Set the new number of MC addresses that we are being requested to use. */ @@ -6241,7 +6241,7 @@ e1000_check_polarity(struct e1000_hw *hw, * 1 - Downshift ocured. * * returns: - E1000_ERR_XXX - * E1000_SUCCESS + * E1000_SUCCESS * * For phy's older then IGP, this function reads the Downshift bit in the Phy * Specific Status register. For IGP phy's, it reads the Downgrade bit in the @@ -6256,7 +6256,7 @@ e1000_check_downshift(struct e1000_hw *hw) DEBUGFUNC("e1000_check_downshift"); - if(hw->phy_type == e1000_phy_igp || + if(hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) { ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH, &phy_data); @@ -6685,8 +6685,8 @@ e1000_set_d0_lplu_state(struct e1000_hw *hw, } else { - - phy_data |= IGP02E1000_PM_D0_LPLU; + + phy_data |= IGP02E1000_PM_D0_LPLU; ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); if (ret_val) return ret_val; @@ -6778,7 +6778,7 @@ int32_t e1000_host_if_read_cookie(struct e1000_hw * hw, uint8_t *buffer) { uint8_t i; - uint32_t offset = E1000_MNG_DHCP_COOKIE_OFFSET; + uint32_t offset = E1000_MNG_DHCP_COOKIE_OFFSET; uint8_t length = E1000_MNG_DHCP_COOKIE_LENGTH; length = (length >> 2); @@ -6797,7 +6797,7 @@ e1000_host_if_read_cookie(struct e1000_hw * hw, uint8_t *buffer) * and also checks whether the previous command is completed. * It busy waits in case of previous command is not completed. * - * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or + * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or * timeout * - E1000_SUCCESS for success. ****************************************************************************/ @@ -6821,7 +6821,7 @@ e1000_mng_enable_host_if(struct e1000_hw * hw) msec_delay_irq(1); } - if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) { + if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) { DEBUGOUT("Previous command timeout failed .\n"); return -E1000_ERR_HOST_INTERFACE_COMMAND; } diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h index 03d07ebde4f..467c9ed944f 100644 --- a/drivers/net/e1000/e1000_hw.h +++ b/drivers/net/e1000/e1000_hw.h @@ -375,7 +375,7 @@ struct e1000_host_mng_dhcp_cookie{ }; #endif -int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer, +int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer, uint16_t length); boolean_t e1000_check_mng_mode(struct e1000_hw *hw); boolean_t e1000_enable_tx_pkt_filtering(struct e1000_hw *hw); @@ -1802,7 +1802,7 @@ struct e1000_hw { * value2 = [0..64512], default=4096 * value3 = [0..64512], default=0 */ - + #define E1000_PSRCTL_BSIZE0_MASK 0x0000007F #define E1000_PSRCTL_BSIZE1_MASK 0x00003F00 #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000 diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index df819c1275a..ccbe342198a 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -349,7 +349,7 @@ e1000_update_mng_vlan(struct e1000_adapter *adapter) * For ASF and Pass Through versions of f/w this means that the * driver is no longer loaded. For AMT version (only with 82573) i * of the f/w this means that the netowrk i/f is closed. - * + * **/ static void @@ -381,10 +381,10 @@ e1000_release_hw_control(struct e1000_adapter *adapter) * @adapter: address of board private structure * * e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit. - * For ASF and Pass Through versions of f/w this means that - * the driver is loaded. For AMT version (only with 82573) + * For ASF and Pass Through versions of f/w this means that + * the driver is loaded. For AMT version (only with 82573) * of the f/w this means that the netowrk i/f is open. - * + * **/ static void @@ -714,8 +714,8 @@ e1000_probe(struct pci_dev *pdev, DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n"); /* if ksp3, indicate if it's port a being setup */ - if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 && - e1000_ksp3_port_a == 0) + if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 && + e1000_ksp3_port_a == 0) adapter->ksp3_port_a = 1; e1000_ksp3_port_a++; /* Reset for multiple KP3 adapters */ @@ -743,9 +743,9 @@ e1000_probe(struct pci_dev *pdev, if (pci_using_dac) netdev->features |= NETIF_F_HIGHDMA; - /* hard_start_xmit is safe against parallel locking */ - netdev->features |= NETIF_F_LLTX; - + /* hard_start_xmit is safe against parallel locking */ + netdev->features |= NETIF_F_LLTX; + adapter->en_mng_pt = e1000_enable_mng_pass_thru(&adapter->hw); /* before reading the EEPROM, reset the controller to @@ -2773,7 +2773,7 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev) unsigned int nr_frags = 0; unsigned int mss = 0; int count = 0; - int tso; + int tso; unsigned int f; len -= skb->data_len; @@ -2786,7 +2786,7 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev) #ifdef NETIF_F_TSO mss = skb_shinfo(skb)->tso_size; - /* The controller does a simple calculation to + /* The controller does a simple calculation to * make sure there is enough room in the FIFO before * initiating the DMA for each buffer. The calc is: * 4 = ceil(buffer len/mss). To make sure we don't @@ -2809,7 +2809,7 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev) case e1000_82573: pull_size = min((unsigned int)4, skb->data_len); if (!__pskb_pull_tail(skb, pull_size)) { - printk(KERN_ERR + printk(KERN_ERR "__pskb_pull_tail failed.\n"); dev_kfree_skb_any(skb); return NETDEV_TX_OK; @@ -3755,7 +3755,7 @@ e1000_clean_rx_irq_ps(struct e1000_adapter *adapter, * throughput, so unsplit small packets and save the alloc/put*/ if (l1 && ((length + l1) <= adapter->rx_ps_bsize0)) { u8 *vaddr; - /* there is no documentation about how to call + /* there is no documentation about how to call * kmap_atomic, so we can't hold the mapping * very long */ pci_dma_sync_single_for_cpu(pdev, -- cgit v1.2.3-70-g09d2 From a1943b5a796a11ee516f5c085453d653a87ee8fe Mon Sep 17 00:00:00 2001 From: Auke Kok Date: Tue, 23 May 2006 13:36:10 -0700 Subject: e1000: Fix date string in Makefile I forgot to update the date string in the Makefile last time. Signed-off-by: Auke Kok --- drivers/net/e1000/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/e1000/Makefile b/drivers/net/e1000/Makefile index 92823ac89d4..5dea2b7dea4 100644 --- a/drivers/net/e1000/Makefile +++ b/drivers/net/e1000/Makefile @@ -1,7 +1,7 @@ ################################################################################ # # -# Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved. +# Copyright(c) 1999 - 2006 Intel Corporation. All rights reserved. # # This program is free software; you can redistribute it and/or modify it # under the terms of the GNU General Public License as published by the Free -- cgit v1.2.3-70-g09d2 From fdf35d3c49be0ad99e2fd5f5f27c6c0c336a3f11 Mon Sep 17 00:00:00 2001 From: Auke Kok Date: Tue, 23 May 2006 13:36:14 -0700 Subject: e1000: remove changelog in driver This honours the request to remove the changelog in the driver code. Signed-off-by: Auke Kok --- drivers/net/e1000/e1000_main.c | 39 --------------------------------------- 1 file changed, 39 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index ccbe342198a..95069ace1de 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -29,45 +29,6 @@ #include "e1000.h" -/* Change Log - * 7.0.33 3-Feb-2006 - * o Added another fix for the pass false carrier bit - * 7.0.32 24-Jan-2006 - * o Need to rebuild with noew version number for the pass false carrier - * fix in e1000_hw.c - * 7.0.30 18-Jan-2006 - * o fixup for tso workaround to disable it for pci-x - * o fix mem leak on 82542 - * o fixes for 10 Mb/s connections and incorrect stats - * 7.0.28 01/06/2006 - * o hardware workaround to only set "speed mode" bit for 1G link. - * 7.0.26 12/23/2005 - * o wake on lan support modified for device ID 10B5 - * o fix dhcp + vlan issue not making it to the iAMT firmware - * 7.0.24 12/9/2005 - * o New hardware support for the Gigabit NIC embedded in the south bridge - * o Fixes to the recycling logic (skb->tail) from IBM LTC - * 6.3.9 12/16/2005 - * o incorporate fix for recycled skbs from IBM LTC - * 6.3.7 11/18/2005 - * o Honor eeprom setting for enabling/disabling Wake On Lan - * 6.3.5 11/17/2005 - * o Fix memory leak in rx ring handling for PCI Express adapters - * 6.3.4 11/8/05 - * o Patch from Jesper Juhl to remove redundant NULL checks for kfree - * 6.3.2 9/20/05 - * o Render logic that sets/resets DRV_LOAD as inline functions to - * avoid code replication. If f/w is AMT then set DRV_LOAD only when - * network interface is open. - * o Handle DRV_LOAD set/reset in cases where AMT uses VLANs. - * o Adjust PBA partioning for Jumbo frames using MTU size and not - * rx_buffer_len - * 6.3.1 9/19/05 - * o Use adapter->tx_timeout_factor in Tx Hung Detect logic - * (e1000_clean_tx_irq) - * o Support for 8086:10B5 device (Quad Port) - */ - char e1000_driver_name[] = "e1000"; static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver"; #ifndef CONFIG_E1000_NAPI -- cgit v1.2.3-70-g09d2 From 440c052d6f717495806fe2c65f3f5677c92397c7 Mon Sep 17 00:00:00 2001 From: Auke Kok Date: Tue, 23 May 2006 13:36:19 -0700 Subject: e1000: bump version to 7.0.38-k4 Signed-off-by: Auke Kok --- drivers/net/e1000/e1000_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index 95069ace1de..258c7d53930 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -36,7 +36,7 @@ static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver"; #else #define DRIVERNAPI "-NAPI" #endif -#define DRV_VERSION "7.0.38-k2"DRIVERNAPI +#define DRV_VERSION "7.0.38-k4"DRIVERNAPI char e1000_driver_version[] = DRV_VERSION; static char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation."; -- cgit v1.2.3-70-g09d2