From 53d7168026a440c4cba25468a3d926ddd7ab030a Mon Sep 17 00:00:00 2001 From: Stelian Pop Date: Sat, 5 Apr 2008 21:14:03 +0100 Subject: [ARM] 4933/1: AT91CAP9 UDPHS driver: generic AT91 parts. This is patch 1 of 2 adding support for the USB High Speed Device Port on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP as the AVR32 and the AT91SAM9RL. This patch makes the generic AT91 adaptations, mainly dealing with the addition of the UDPHS UTMI clock. Signed-off-by: Stelian Pop Acked-by: Haavard Skinnemoen Acked-by: Andrew Victor Signed-off-by: Russell King --- include/asm-arm/arch-at91/board.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/asm-arm/arch-at91/board.h') diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h index dc189f01c5b..1f247028686 100644 --- a/include/asm-arm/arch-at91/board.h +++ b/include/asm-arm/arch-at91/board.h @@ -36,6 +36,7 @@ #include #include #include +#include /* USB Device */ struct at91_udc_data { @@ -45,6 +46,9 @@ struct at91_udc_data { }; extern void __init at91_add_device_udc(struct at91_udc_data *data); + /* USB High Speed Device */ +extern void __init at91_add_device_usba(struct usba_platform_data *data); + /* Compact Flash */ struct at91_cf_data { u8 irq_pin; /* I/O IRQ */ -- cgit v1.2.3-70-g09d2 From 613526677a74c2b3d1b1696ea7334b2cf35155b3 Mon Sep 17 00:00:00 2001 From: sedji gaouaou Date: Thu, 10 Jul 2008 10:15:35 +0100 Subject: [ARM] 5130/4: Support for the at91sam9g20 Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC. AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. We created a new board for this device but based the chip support directly on 9260 files with little updates. Here is the chip page on Atmel wabsite: http://atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Sedji Gaouaou Signed-off-by: Justin Waters Acked-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/Kconfig | 29 +++- arch/arm/mach-at91/Makefile | 4 + arch/arm/mach-at91/at91sam9260.c | 16 +++ arch/arm/mach-at91/at91sam9260_devices.c | 44 +++++-- arch/arm/mach-at91/board-sam9g20ek.c | 218 +++++++++++++++++++++++++++++++ arch/arm/mach-at91/clock.c | 19 ++- arch/arm/mach-at91/pm.c | 2 +- arch/arm/mm/Kconfig | 4 +- drivers/net/Kconfig | 2 +- drivers/usb/gadget/at91_udc.c | 4 +- include/asm-arm/arch-at91/at91sam9260.h | 11 ++ include/asm-arm/arch-at91/board.h | 2 +- include/asm-arm/arch-at91/cpu.h | 7 + include/asm-arm/arch-at91/hardware.h | 2 +- include/asm-arm/arch-at91/timex.h | 5 + sound/soc/at91/at91-ssc.c | 2 +- 16 files changed, 342 insertions(+), 29 deletions(-) create mode 100644 arch/arm/mach-at91/board-sam9g20ek.c (limited to 'include/asm-arm/arch-at91/board.h') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index cae5c67dc31..5bad6b9b00d 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -30,6 +30,11 @@ config ARCH_AT91SAM9RL select GENERIC_TIME select GENERIC_CLOCKEVENTS +config ARCH_AT91SAM9G20 + bool "AT91SAM9G20" + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + config ARCH_AT91CAP9 bool "AT91CAP9" select GENERIC_TIME @@ -239,6 +244,20 @@ endif # ---------------------------------------------------------- +if ARCH_AT91SAM9G20 + +comment "AT91SAM9G20 Board Type" + +config MACH_AT91SAM9G20EK + bool "Atmel AT91SAM9G20-EK Evaluation Kit" + depends on ARCH_AT91SAM9G20 + help + Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit. + +endif + +# ---------------------------------------------------------- + if ARCH_AT91CAP9 comment "AT91CAP9 Board Type" @@ -274,13 +293,13 @@ comment "AT91 Board Options" config MTD_AT91_DATAFLASH_CARD bool "Enable DataFlash Card support" - depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK || MACH_SAM9_L9260 || MACH_ECBAT91) + depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK) help Enable support for the DataFlash card. config MTD_NAND_AT91_BUSWIDTH_16 bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK) + depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK) help On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). @@ -329,15 +348,15 @@ config AT91_EARLY_USART2 config AT91_EARLY_USART3 bool "USART3" - depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260) + depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20) config AT91_EARLY_USART4 bool "USART4" - depends on ARCH_AT91SAM9260 + depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 config AT91_EARLY_USART5 bool "USART5" - depends on ARCH_AT91SAM9260 + depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 endchoice diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 932d17109e8..7d641f97516 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_d obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o +obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o obj-$(CONFIG_ARCH_AT91CAP9) += at91cap9.o at91sam926x_time.o at91cap9_devices.o obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o @@ -49,6 +50,9 @@ obj-$(CONFIG_MACH_USB_A9263) += board-usb-a9263.o # AT91SAM9RL board-specific support obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o +# AT91SAM9G20 board-specific support +obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o + # AT91CAP9 board-specific support obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index ee26550cdc2..380f12a1220 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -47,6 +47,20 @@ static struct map_desc at91sam9260_sram_desc[] __initdata = { } }; +static struct map_desc at91sam9g20_sram_desc[] __initdata = { + { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE, + .pfn = __phys_to_pfn(AT91SAM9G20_SRAM0_BASE), + .length = AT91SAM9G20_SRAM0_SIZE, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE - AT91SAM9G20_SRAM1_SIZE, + .pfn = __phys_to_pfn(AT91SAM9G20_SRAM1_BASE), + .length = AT91SAM9G20_SRAM1_SIZE, + .type = MT_DEVICE, + } +}; + static struct map_desc at91sam9xe_sram_desc[] __initdata = { { .pfn = __phys_to_pfn(AT91SAM9XE_SRAM_BASE), @@ -307,6 +321,8 @@ void __init at91sam9260_initialize(unsigned long main_clock) if (cpu_is_at91sam9xe()) at91sam9xe_initialize(); + else if (cpu_is_at91sam9g20()) + iotable_init(at91sam9g20_sram_desc, ARRAY_SIZE(at91sam9g20_sram_desc)); else iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc)); diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index 26f5cacbec3..86cba4ac29b 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -18,6 +18,7 @@ #include #include +#include #include #include #include @@ -320,20 +321,41 @@ void __init at91_add_device_nand(struct at91_nand_data *data) csa = at91_sys_read(AT91_MATRIX_EBICSA); at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); - /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) - | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); + if (cpu_is_at91sam9260()) { + /* Timing for sam9260 */ + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) - | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) + | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); - if (data->bus_width_16) - mode = AT91_SMC_DBW_16; - else - mode = AT91_SMC_DBW_8; - at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); + } + + if (cpu_is_at91sam9g20()) { + /* Timing for sam9g20 */ + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); + + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4) + | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4)); + + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3)); + } /* enable pin */ if (data->enable_pin) diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c new file mode 100644 index 00000000000..45617c20124 --- /dev/null +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -0,0 +1,218 @@ +/* + * Copyright (C) 2005 SAN People + * Copyright (C) 2008 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +static void __init ek_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9260_initialize(18432000); + + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init ek_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if !defined(CONFIG_MMC_AT91) + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +#endif +}; + + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PA7, + .is_rmii = 1, +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Bootstrap", + .offset = 0, + .size = 4 * 1024 * 1024, + }, + { + .name = "Partition 1", + .offset = 4 * 1024 * 1024, + .size = 60 * 1024 * 1024, + }, + { + .name = "Partition 2", + .offset = 64 * 1024 * 1024, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +/* det_pin is not connected */ +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + + +/* + * MCI (SD/MMC) + * det_pin, wp_pin and vcc_pin are not connected + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, + .wire4 = 1, +}; + + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* "bottom" led, green, userled1 to be defined */ + .name = "ds5", + .gpio = AT91_PIN_PA6, + .active_low = 1, + .default_trigger = "none", + }, + { /* "power" led, yellow */ + .name = "ds1", + .gpio = AT91_PIN_PA9, + .default_trigger = "heartbeat", + } +}; + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* MMC */ + at91_add_device_mmc(0, &ek_mmc_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* LEDs */ + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); +} + +MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index e8ce8f0f3ed..464bdbbf74d 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -515,14 +515,19 @@ static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq) /* * PLL input between 1MHz and 32MHz per spec, but lower * frequences seem necessary in some cases so allow 100K. + * Warning: some newer products need 2MHz min. */ input = main_freq / i; + if (cpu_is_at91sam9g20() && input < 2000000) + continue; if (input < 100000) continue; if (input > 32000000) continue; mul1 = out_freq / input; + if (cpu_is_at91sam9g20() && mul > 63) + continue; if (mul1 > 2048) continue; if (mul1 < 2) @@ -582,7 +587,8 @@ int __init at91_clock_init(unsigned long main_clock) /* report if PLLA is more than mildly overclocked */ plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR)); - if (plla.rate_hz > 209000000) + if ((!cpu_is_at91sam9g20() && plla.rate_hz > 209000000) + || (cpu_is_at91sam9g20() && plla.rate_hz > 800000000)) pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000); /* @@ -597,7 +603,7 @@ int __init at91_clock_init(unsigned long main_clock) uhpck.pmc_mask = AT91RM9200_PMC_UHP; udpck.pmc_mask = AT91RM9200_PMC_UDP; at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP); - } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) { + } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { uhpck.pmc_mask = AT91SAM926x_PMC_UHP; udpck.pmc_mask = AT91SAM926x_PMC_UDP; } else if (cpu_is_at91cap9()) { @@ -629,8 +635,13 @@ int __init at91_clock_init(unsigned long main_clock) freq /= (1 << ((mckr & AT91_PMC_PRES) >> 2)); /* prescale */ if (cpu_is_at91rm9200()) mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ - else - mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ + else if (cpu_is_at91sam9g20()) { + mck.rate_hz = (mckr & AT91_PMC_MDIV) ? + freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq; /* mdiv ; (x >> 7) = ((x >> 8) * 2) */ + if (mckr & AT91_PMC_PDIV) + freq /= 2; /* processor clock division */ + } else + mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ /* Register the PMC's standard clocks */ for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++) diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index aa863c15770..8ab4feb1ec5 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -202,7 +202,7 @@ static int at91_pm_verify_clocks(void) pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n"); return 0; } - } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) { + } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { if ((scsr & (AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP)) != 0) { pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n"); return 0; diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 33ed048502a..750d895cd28 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -180,8 +180,8 @@ config CPU_ARM925T # ARM926T config CPU_ARM926T bool "Support ARM926T processor" - depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI - default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI + depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI + default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI select CPU_32v5 select CPU_ABRT_EV5TJ select CPU_PABRT_NOIFAR diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 9f6cc8a5607..be3b13cf417 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -217,7 +217,7 @@ config MII config MACB tristate "Atmel MACB support" - depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91CAP9 + depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 select PHYLIB help The Atmel MACB ethernet interface is found on many AT32 and AT91 diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c index 274c60a970c..b6b2a0a5ba3 100644 --- a/drivers/usb/gadget/at91_udc.c +++ b/drivers/usb/gadget/at91_udc.c @@ -888,7 +888,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, 0); if (cpu_is_at91rm9200()) gpio_set_value(udc->board.pullup_pin, active); - else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc |= AT91_UDP_TXVC_PUON; @@ -906,7 +906,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS); if (cpu_is_at91rm9200()) gpio_set_value(udc->board.pullup_pin, !active); - else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc &= ~AT91_UDP_TXVC_PUON; diff --git a/include/asm-arm/arch-at91/at91sam9260.h b/include/asm-arm/arch-at91/at91sam9260.h index c8934fe34dc..889872a3f2a 100644 --- a/include/asm-arm/arch-at91/at91sam9260.h +++ b/include/asm-arm/arch-at91/at91sam9260.h @@ -6,6 +6,8 @@ * Common definitions. * Based on AT91SAM9260 datasheet revision A (Preliminary). * + * Includes also definitions for AT91SAM9XE and AT91SAM9G families + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -123,5 +125,14 @@ #define AT91SAM9XE_FLASH_BASE 0x00200000 /* Internal FLASH base address */ #define AT91SAM9XE_SRAM_BASE 0x00300000 /* Internal SRAM base address */ +#define AT91SAM9G20_ROM_BASE 0x00100000 /* Internal ROM base address */ +#define AT91SAM9G20_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ + +#define AT91SAM9G20_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */ +#define AT91SAM9G20_SRAM0_SIZE SZ_16K /* Internal SRAM 0 size (16Kb) */ +#define AT91SAM9G20_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */ +#define AT91SAM9G20_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */ + +#define AT91SAM9G20_UHP_BASE 0x00500000 /* USB Host controller */ #endif diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h index 1f247028686..94de788da76 100644 --- a/include/asm-arm/arch-at91/board.h +++ b/include/asm-arm/arch-at91/board.h @@ -77,7 +77,7 @@ struct at91_eth_data { }; extern void __init at91_add_device_eth(struct at91_eth_data *data); -#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9) +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) #define eth_platform_data at91_eth_data #endif diff --git a/include/asm-arm/arch-at91/cpu.h b/include/asm-arm/arch-at91/cpu.h index 7145166826a..52df794205c 100644 --- a/include/asm-arm/arch-at91/cpu.h +++ b/include/asm-arm/arch-at91/cpu.h @@ -21,6 +21,7 @@ #define ARCH_ID_AT91SAM9260 0x019803a0 #define ARCH_ID_AT91SAM9261 0x019703a0 #define ARCH_ID_AT91SAM9263 0x019607a0 +#define ARCH_ID_AT91SAM9G20 0x019905a0 #define ARCH_ID_AT91SAM9RL64 0x019b03a0 #define ARCH_ID_AT91CAP9 0x039A03A0 @@ -63,6 +64,12 @@ static inline unsigned long at91_arch_identify(void) #define cpu_is_at91sam9260() (0) #endif +#ifdef CONFIG_ARCH_AT91SAM9G20 +#define cpu_is_at91sam9g20() (at91_cpu_identify() == ARCH_ID_AT91SAM9G20) +#else +#define cpu_is_at91sam9g20() (0) +#endif + #ifdef CONFIG_ARCH_AT91SAM9261 #define cpu_is_at91sam9261() (at91_cpu_identify() == ARCH_ID_AT91SAM9261) #else diff --git a/include/asm-arm/arch-at91/hardware.h b/include/asm-arm/arch-at91/hardware.h index 2c826d8247a..016a3a3f663 100644 --- a/include/asm-arm/arch-at91/hardware.h +++ b/include/asm-arm/arch-at91/hardware.h @@ -18,7 +18,7 @@ #if defined(CONFIG_ARCH_AT91RM9200) #include -#elif defined(CONFIG_ARCH_AT91SAM9260) +#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) #include #elif defined(CONFIG_ARCH_AT91SAM9261) #include diff --git a/include/asm-arm/arch-at91/timex.h b/include/asm-arm/arch-at91/timex.h index 6e084eb839d..298d8313cda 100644 --- a/include/asm-arm/arch-at91/timex.h +++ b/include/asm-arm/arch-at91/timex.h @@ -57,6 +57,11 @@ #define AT91SAM9_MASTER_CLOCK 100000000 #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) +#elif defined(CONFIG_ARCH_AT91SAM9G20) + +#define AT91SAM9_MASTER_CLOCK 132096000 +#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) + #elif defined(CONFIG_ARCH_AT91CAP9) #define AT91CAP9_MASTER_CLOCK 100000000 diff --git a/sound/soc/at91/at91-ssc.c b/sound/soc/at91/at91-ssc.c index bc35d00a38f..1a426095014 100644 --- a/sound/soc/at91/at91-ssc.c +++ b/sound/soc/at91/at91-ssc.c @@ -41,7 +41,7 @@ #define DBG(x...) #endif -#if defined(CONFIG_ARCH_AT91SAM9260) +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) #define NUM_SSC_DEVICES 1 #else #define NUM_SSC_DEVICES 3 -- cgit v1.2.3-70-g09d2