/* * Copyright (C) 1994-1998 Linus Torvalds & authors (see below) * Copyright (C) 2005, 2007 Bartlomiej Zolnierkiewicz */ /* * Mostly written by Mark Lord * and Gadi Oxman * and Andre Hedrick * * See linux/MAINTAINERS for address of current maintainer. * * This is the IDE probe module, as evolved from hd.c and ide.c. * * -- increase WAIT_PIDENTIFY to avoid CD-ROM locking at boot * by Andrea Arcangeli */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include /** * generic_id - add a generic drive id * @drive: drive to make an ID block for * * Add a fake id field to the drive we are passed. This allows * use to skip a ton of NULL checks (which people always miss) * and make drive properties unconditional outside of this file */ static void generic_id(ide_drive_t *drive) { u16 *id = drive->id; id[ATA_ID_CUR_CYLS] = id[ATA_ID_CYLS] = drive->cyl; id[ATA_ID_CUR_HEADS] = id[ATA_ID_HEADS] = drive->head; id[ATA_ID_CUR_SECTORS] = id[ATA_ID_SECTORS] = drive->sect; } static void ide_disk_init_chs(ide_drive_t *drive) { u16 *id = drive->id; /* Extract geometry if we did not already have one for the drive */ if (!drive->cyl || !drive->head || !drive->sect) { drive->cyl = drive->bios_cyl = id[ATA_ID_CYLS]; drive->head = drive->bios_head = id[ATA_ID_HEADS]; drive->sect = drive->bios_sect = id[ATA_ID_SECTORS]; } /* Handle logical geometry translation by the drive */ if (ata_id_current_chs_valid(id)) { drive->cyl = id[ATA_ID_CUR_CYLS]; drive->head = id[ATA_ID_CUR_HEADS]; drive->sect = id[ATA_ID_CUR_SECTORS]; } /* Use physical geometry if what we have still makes no sense */ if (drive->head > 16 && id[ATA_ID_HEADS] && id[ATA_ID_HEADS] <= 16) { drive->cyl = id[ATA_ID_CYLS]; drive->head = id[ATA_ID_HEADS]; drive->sect = id[ATA_ID_SECTORS]; } } static void ide_disk_init_mult_count(ide_drive_t *drive) { u16 *id = drive->id; u8 max_multsect = id[ATA_ID_MAX_MULTSECT] & 0xff; if (max_multsect) { if ((max_multsect / 2) > 1) id[ATA_ID_MULTSECT] = max_multsect | 0x100; else id[ATA_ID_MULTSECT] &= ~0x1ff; drive->mult_req = id[ATA_ID_MULTSECT] & 0xff; if (drive->mult_req) drive->special.b.set_multmode = 1; } } /** * do_identify - identify a drive * @drive: drive to identify * @cmd: command used * * Called when we have issued a drive identify command to * read and parse the results. This function is run with * interrupts disabled. */ static inline void do_identify (ide_drive_t *drive, u8 cmd) { ide_hwif_t *hwif = HWIF(drive); u16 *id = drive->id; char *m = (char *)&id[ATA_ID_PROD]; int bswap = 1; /* read 512 bytes of id info */ hwif->tp_ops->input_data(drive, NULL, id, SECTOR_SIZE); drive->id_read = 1; local_irq_enable(); #ifdef DEBUG printk(KERN_INFO "%s: dumping identify data\n", drive->name); ide_dump_identify((u8 *)id); #endif ide_fix_driveid(id); /* * ATA_CMD_ID_ATA returns little-endian info, * ATA_CMD_ID_ATAPI *usually* returns little-endian info. */ if (cmd == ATA_CMD_ID_ATAPI) { if ((m[0] == 'N' && m[1] == 'E') || /* NEC */ (m[0] == 'F' && m[1] == 'X') || /* Mitsumi */ (m[0] == 'P' && m[1] == 'i')) /* Pioneer */ /* Vertos drives may still be weird */ bswap ^= 1; } ide_fixstring(m, ATA_ID_PROD_LEN, bswap); ide_fixstring((char *)&id[ATA_ID_FW_REV], ATA_ID_FW_REV_LEN, bswap); ide_fixstring((char *)&id[ATA_ID_SERNO], ATA_ID_SERNO_LEN, bswap); /* we depend on this a lot! */ m[ATA_ID_PROD_LEN - 1] = '\0'; if (strstr(m, "E X A B Y T E N E S T")) goto err_misc; printk(KERN_INFO "%s: %s, ", drive->name, m); drive->present = 1; drive->dead = 0; /* * Check for an ATAPI device */ if (cmd == ATA_CMD_ID_ATAPI) { u8 type = (id[ATA_ID_CONFIG] >> 8) & 0x1f; printk(KERN_CONT "ATAPI "); switch (type) { case ide_floppy: if (!strstr(m, "CD-ROM")) { if (!strstr(m, "oppy") && !strstr(m, "poyp") && !strstr(m, "ZIP")) printk(KERN_CONT "cdrom or floppy?, assuming "); if (drive->media != ide_cdrom) { printk(KERN_CONT "FLOPPY"); drive->removable = 1; break; } } /* Early cdrom models used zero */ type = ide_cdrom; case ide_cdrom: drive->removable = 1; #ifdef CONFIG_PPC /* kludge for Apple PowerBook internal zip */ if (!strstr(m, "CD-ROM") && strstr(m, "ZIP")) { printk(KERN_CONT "FLOPPY"); type = ide_floppy; break; } #endif printk(KERN_CONT "CD/DVD-ROM"); break; case ide_tape: printk(KERN_CONT "TAPE"); break; case ide_optical: printk(KERN_CONT "OPTICAL"); drive->removable = 1; break; default: printk(KERN_CONT "UNKNOWN (type %d)", type); break; } printk(KERN_CONT " drive\n"); drive->media = type; /* an ATAPI device ignores DRDY */ drive->ready_stat = 0; return; } /* * Not an ATAPI device: looks like a "regular" hard disk */ /* * 0x848a = CompactFlash device * These are *not* removable in Linux definition of the term */ if (id[ATA_ID_CONFIG] != 0x848a && (id[ATA_ID_CONFIG] & (1 << 7))) drive->removable = 1; drive->media = ide_disk; printk(KERN_CONT "%s DISK drive\n", (id[ATA_ID_CONFIG] == 0x848a) ? "CFA" : "ATA"); return; err_misc: kfree(id); drive->present = 0; return; } /** * actual_try_to_identify - send ata/atapi identify * @drive: drive to identify * @cmd: command to use * * try_to_identify() sends an ATA(PI) IDENTIFY request to a drive * and waits for a response. It also monitors irqs while this is * happening, in hope of automatically determining which one is * being used by the interface. * * Returns: 0 device was identified * 1 device timed-out (no response to identify request) * 2 device aborted the command (refused to identify itself) */ static int actual_try_to_identify (ide_drive_t *drive, u8 cmd) { ide_hwif_t *hwif = HWIF(drive); struct ide_io_ports *io_ports = &hwif->io_ports; const struct ide_tp_ops *tp_ops = hwif->tp_ops; int use_altstatus = 0, rc; unsigned long timeout; u8 s = 0, a = 0; /* take a deep breath */ msleep(50); if (io_ports->ctl_addr) { a = tp_ops->read_altstatus(hwif); s = tp_ops->read_status(hwif); if ((a ^ s) & ~ATA_IDX) /* ancient Seagate drives, broken interfaces */ printk(KERN_INFO "%s: probing with STATUS(0x%02x) " "instead of ALTSTATUS(0x%02x)\n", drive->name, s, a); else /* use non-intrusive polling */ use_altstatus = 1; } /* set features register for atapi * identify command to be sure of reply */ if (cmd == ATA_CMD_ID_ATAPI) { ide_task_t task; memset(&task, 0, sizeof(task)); /* disable DMA & overlap */ task.tf_flags = IDE_TFLAG_OUT_FEATURE; tp_ops->tf_load(drive, &task); } /* ask drive for ID */ tp_ops->exec_command(hwif, cmd); timeout = ((cmd == ATA_CMD_ID_ATA) ? WAIT_WORSTCASE : WAIT_PIDENTIFY) / 2; if (ide_busy_sleep(hwif, timeout, use_altstatus)) return 1; /* wait for IRQ and ATA_DRQ */ msleep(50); s = tp_ops->read_status(hwif); if (OK_STAT(s, ATA_DRQ, BAD_R_STAT)) { unsigned long flags; /* local CPU only; some systems need this */ local_irq_save(flags); /* drive returned ID */ do_identify(drive, cmd); /* drive responded with ID */ rc = 0; /* clear drive IRQ */ (void)tp_ops->read_status(hwif); local_irq_restore(flags); } else { /* drive refused ID */ rc = 2; } return rc; } /** * try_to_identify - try to identify a drive * @drive: drive to probe * @cmd: command to use * * Issue the identify command and then do IRQ probing to * complete the identification when needed by finding the * IRQ the drive is attached to */ static int try_to_identify (ide_drive_t *drive, u8 cmd) { ide_hwif_t *hwif = HWIF(drive); const struct ide_tp_ops *tp_ops = hwif->tp_ops; int retval; int autoprobe = 0; unsigned long cookie = 0; /* * Disable device irq unless we need to * probe for it. Otherwise we'll get spurious * interrupts during the identify-phase that * the irq handler isn't expecting. */ if (hwif->io_ports.ctl_addr) { if (!hwif->irq) { autoprobe = 1; cookie = probe_irq_on(); } tp_ops->set_irq(hwif, autoprobe); } retval = actual_try_to_identify(drive, cmd); if (autoprobe) { int irq; tp_ops->set_irq(hwif, 0); /* clear drive IRQ */ (void)tp_ops->read_status(hwif); udelay(5); irq = probe_irq_off(cookie); if (!hwif->irq) { if (irq > 0) { hwif->irq = irq; } else { /* Mmmm.. multiple IRQs.. * don't know which was ours */ printk(KERN_ERR "%s: IRQ probe failed (0x%lx)\n", drive->name, cookie); } } } return retval; } int ide_busy_sleep(ide_hwif_t *hwif, unsigned long timeout, int altstatus) { u8 stat; timeout += jiffies; do { msleep(50); /* give drive a breather */ stat = altstatus ? hwif->tp_ops->read_altstatus(hwif) : hwif->tp_ops->read_status(hwif); if ((stat & ATA_BUSY) == 0) return 0; } while (time_before(jiffies, timeout)); return 1; /* drive timed-out */ } static u8 ide_read_device(ide_drive_t *drive) { ide_task_t task; memset(&task, 0, sizeof(task)); task.tf_flags = IDE_TFLAG_IN_DEVICE; drive->hwif->tp_ops->tf_read(drive, &task); return task.tf.device; } /** * do_probe - probe an IDE device * @drive: drive to probe * @cmd: command to use * * do_probe() has the difficult job of finding a drive if it exists, * without getting hung up if it doesn't exist, without trampling on * ethernet cards, and without leaving any IRQs dangling to haunt us later. * * If a drive is "known" to exist (from CMOS or kernel parameters), * but does not respond right away, the probe will "hang in there" * for the maximum wait time (about 30 seconds), otherwise it will * exit much more quickly. * * Returns: 0 device was identified * 1 device timed-out (no response to identify request) * 2 device aborted the command (refused to identify itself) * 3 bad status from device (possible for ATAPI drives) * 4 probe was not attempted because failure was obvious */ static int do_probe (ide_drive_t *drive, u8 cmd) { ide_hwif_t *hwif = HWIF(drive); const struct ide_tp_ops *tp_ops = hwif->tp_ops; int rc; u8 stat; if (drive->present) { /* avoid waiting for inappropriate probes */ if (drive->media != ide_disk && cmd == ATA_CMD_ID_ATA) return 4; } #ifdef DEBUG printk(KERN_INFO "probing for %s: present=%d, media=%d, probetype=%s\n", drive->name, drive->present, drive->media, (cmd == ATA_CMD_ID_ATA) ? "ATA" : "ATAPI"); #endif /* needed for some systems * (e.g. crw9624 as drive0 with disk as slave) */ msleep(50); SELECT_DRIVE(drive); msleep(50); if (ide_read_device(drive) != drive->select.all && !drive->present) { if (drive->select.b.unit != 0) { /* exit with drive0 selected */ SELECT_DRIVE(&hwif->drives[0]); /* allow ATA_BUSY to assert & clear */ msleep(50); } /* no i/f present: mmm.. this should be a 4 -ml */ return 3; } stat = tp_ops->read_status(hwif); if (OK_STAT(stat, ATA_DRDY, ATA_BUSY) || drive->present || cmd == ATA_CMD_ID_ATAPI) { /* send cmd and wait */ if ((rc = try_to_identify(drive, cmd))) { /* failed: try again */ rc = try_to_identify(drive,cmd); } stat = tp_ops->read_status(hwif); if (stat == (ATA_BUSY | ATA_DRDY)) return 4; if (rc == 1 && cmd == ATA_CMD_ID_ATAPI) { printk(KERN_ERR "%s: no response (status = 0x%02x), " "resetting drive\n", drive->name, stat); msleep(50); SELECT_DRIVE(drive); msleep(50); tp_ops->exec_command(hwif, ATA_CMD_DEV_RESET); (void)ide_busy_sleep(hwif, WAIT_WORSTCASE, 0); rc = try_to_identify(drive, cmd); } /* ensure drive IRQ is clear */ stat = tp_ops->read_status(hwif); if (rc == 1) printk(KERN_ERR "%s: no response (status = 0x%02x)\n", drive->name, stat); } else { /* not present or maybe ATAPI */ rc = 3; } if (drive->select.b.unit != 0) { /* exit with drive0 selected */ SELECT_DRIVE(&hwif->drives[0]); msleep(50); /* ensure drive irq is clear */ (void)tp_ops->read_status(hwif); } return rc; } /* * */ static void enable_nest (ide_drive_t *drive) { ide_hwif_t *hwif = HWIF(drive); const struct ide_tp_ops *tp_ops = hwif->tp_ops; u8 stat; printk(KERN_INFO "%s: enabling %s -- ", hwif->name, (char *)&drive->id[ATA_ID_PROD]); SELECT_DRIVE(drive); msleep(50); tp_ops->exec_command(hwif, ATA_EXABYTE_ENABLE_NEST); if (ide_busy_sleep(hwif, WAIT_WORSTCASE, 0)) { printk(KERN_CONT "failed (timeout)\n"); return; } msleep(50); stat = tp_ops->read_status(hwif); if (!OK_STAT(stat, 0, BAD_STAT)) printk(KERN_CONT "failed (status = 0x%02x)\n", stat); else printk(KERN_CONT "success\n"); } /** * probe_for_drives - upper level drive probe * @drive: drive to probe for * * probe_for_drive() tests for existence of a given drive using do_probe() * and presents things to the user as needed. * * Returns: 0 no device was found * 1 device was found (note: drive->present might * still be 0) */ static inline u8 probe_for_drive (ide_drive_t *drive) { char *m; /* * In order to keep things simple we have an id * block for all drives at all times. If the device * is pre ATA or refuses ATA/ATAPI identify we * will add faked data to this. * * Also note that 0 everywhere means "can't do X" */ drive->id = kzalloc(SECTOR_WORDS *4, GFP_KERNEL); drive->id_read = 0; if(drive->id == NULL) { printk(KERN_ERR "ide: out of memory for id data.\n"); return 0; } m = (char *)&drive->id[ATA_ID_PROD]; strcpy(m, "UNKNOWN"); /* skip probing? */ if (!drive->noprobe) { retry: /* if !(success||timed-out) */ if (do_probe(drive, ATA_CMD_ID_ATA) >= 2) /* look for ATAPI device */ (void)do_probe(drive, ATA_CMD_ID_ATAPI); if (!drive->present) /* drive not found */ return 0; if (strstr(m, "E X A B Y T E N E S T")) { enable_nest(drive); goto retry; } /* identification failed? */ if (!drive->id_read) { if (drive->media == ide_disk) { printk(KERN_INFO "%s: non-IDE drive, CHS=%d/%d/%d\n", drive->name, drive->cyl, drive->head, drive->sect); } else if (drive->media == ide_cdrom) { printk(KERN_INFO "%s: ATAPI cdrom (?)\n", drive->name); } else { /* nuke it */ printk(KERN_WARNING "%s: Unknown device on bus refused identification. Ignoring.\n", drive->name); drive->present = 0; } } /* drive was found */ } if(!drive->present) return 0; /* The drive wasn't being helpful. Add generic info only */ if (drive->id_read == 0) { generic_id(drive); return 1; } if (drive->media == ide_disk) { ide_disk_init_chs(drive); ide_disk_init_mult_count(drive); } return drive->present; } static void hwif_release_dev(struct device *dev) { ide_hwif_t *hwif = container_of(dev, ide_hwif_t, gendev); complete(&hwif->gendev_rel_comp); } static int ide_register_port(ide_hwif_t *hwif) { int ret; /* register with global device tree */ strlcpy(hwif->gendev.bus_id,hwif->name,BUS_ID_SIZE); hwif->gendev.driver_data = hwif; if (hwif->gendev.parent == NULL) { if (hwif->dev) hwif->gendev.parent = hwif->dev; else /* Would like to do = &device_legacy */ hwif->gendev.parent = NULL; } hwif->gendev.release = hwif_release_dev; ret = device_register(&hwif->gendev); if (ret < 0) { printk(KERN_WARNING "IDE: %s: device_register error: %d\n", __func__, ret); goto out; } hwif->portdev = device_create_drvdata(ide_port_class, &hwif->gendev, MKDEV(0, 0), hwif, hwif->name); if (IS_ERR(hwif->portdev)) { ret = PTR_ERR(hwif->portdev); device_unregister(&hwif->gendev); } out: return ret; } /** * ide_port_wait_ready - wait for port to become ready * @hwif: IDE port * * This is needed on some PPCs and a bunch of BIOS-less embedded * platforms. Typical cases are: * * - The firmware hard reset the disk before booting the kernel, * the drive is still doing it's poweron-reset sequence, that * can take up to 30 seconds. * * - The firmware does nothing (or no firmware), the device is * still in POST state (same as above actually). * * - Some CD/DVD/Writer combo drives tend to drive the bus during * their reset sequence even when they are non-selected slave * devices, thus preventing discovery of the main HD. * * Doing this wait-for-non-busy should not harm any existing * configuration and fix some issues like the above. * * BenH. * * Returns 0 on success, error code (< 0) otherwise. */ static int ide_port_wait_ready(ide_hwif_t *hwif) { int unit, rc; printk(KERN_DEBUG "Probing IDE interface %s...\n", hwif->name); /* Let HW settle down a bit from whatever init state we * come from */ mdelay(2); /* Wait for BSY bit to go away, spec timeout is 30 seconds, * I know of at least one disk who takes 31 seconds, I use 35 * here to be safe */ rc = ide_wait_not_busy(hwif, 35000); if (rc) return rc; /* Now make sure both master & slave are ready */ for (unit = 0; unit < MAX_DRIVES; unit++) { ide_drive_t *drive = &hwif->drives[unit]; /* Ignore disks that we will not probe for later. */ if (!drive->noprobe || drive->present) { SELECT_DRIVE(drive); hwif->tp_ops->set_irq(hwif, 1); mdelay(2); rc = ide_wait_not_busy(hwif, 35000); if (rc) goto out; } else printk(KERN_DEBUG "%s: ide_wait_not_busy() skipped\n", drive->name); } out: /* Exit function with master reselected (let's be sane) */ if (unit) SELECT_DRIVE(&hwif->drives[0]); return rc; } /** * ide_undecoded_slave - look for bad CF adapters * @dev1: slave device * * Analyse the drives on the interface and attempt to decide if we * have the same drive viewed twice. This occurs with crap CF adapters * and PCMCIA sometimes. */ void ide_undecoded_slave(ide_drive_t *dev1) { ide_drive_t *dev0 = &dev1->hwif->drives[0]; if ((dev1->dn & 1) == 0 || dev0->present == 0) return; /* If the models don't match they are not the same product */ if (strcmp((char *)&dev0->id[ATA_ID_PROD], (char *)&dev1->id[ATA_ID_PROD])) return; /* Serial numbers do not match */ if (strncmp((char *)&dev0->id[ATA_ID_SERNO], (char *)&dev1->id[ATA_ID_SERNO], ATA_ID_SERNO_LEN)) return; /* No serial number, thankfully very rare for CF */ if (*(char *)&dev0->id[ATA_ID_SERNO] == 0) return; /* Appears to be an IDE flash adapter with decode bugs */ printk(KERN_WARNING "ide-probe: ignoring undecoded slave\n"); dev1->present = 0; } EXPORT_SYMBOL_GPL(ide_undecoded_slave); static int ide_probe_port(ide_hwif_t *hwif) { unsigned long flags; unsigned int irqd; int unit, rc = -ENODEV; BUG_ON(hwif->present); if (hwif->drives[0].noprobe && hwif->drives[1].noprobe) return -EACCES; /* * We must always disable IRQ, as probe_for_drive will assert IRQ, but * we'll install our IRQ driver much later... */ irqd = hwif->irq; if (irqd) disable_irq(hwif->irq); local_irq_set(flags); if (ide_port_wait_ready(hwif) == -EBUSY) printk(KERN_DEBUG "%s: Wait for ready failed before probe !\n", hwif->name); /* * Second drive should only exist if first drive was found, * but a lot of cdrom drives are configured as single slaves. */ for (unit = 0; unit < MAX_DRIVES; ++unit) { ide_drive_t *drive = &hwif->drives[unit]; drive->dn = (hwif->channel ? 2 : 0) + unit; (void) probe_for_drive(drive); if (drive->present) rc = 0; } local_irq_restore(flags); /* * Use cached IRQ number. It might be (and is...) changed by probe * code above */ if (irqd) enable_irq(irqd); return rc; } static void ide_port_tune_devices(ide_hwif_t *hwif) { const struct ide_port_ops *port_ops = hwif->port_ops; int unit; for (unit = 0; unit < MAX_DRIVES; unit++) { ide_drive_t *drive = &hwif->drives[unit]; if (drive->present && port_ops && port_ops->quirkproc) port_ops->quirkproc(drive); } for (unit = 0; unit < MAX_DRIVES; ++unit) { ide_drive_t *drive = &hwif->drives[unit]; if (drive->present) { ide_set_max_pio(drive); drive->nice1 = 1; if (hwif->dma_ops) ide_set_dma(drive); } } for (unit = 0; unit < MAX_DRIVES; ++unit) { ide_drive_t *drive = &hwif->drives[unit]; if (hwif->host_flags & IDE_HFLAG_NO_IO_32BIT) drive->no_io_32bit = 1; else drive->no_io_32bit = drive->id[ATA_ID_DWORD_IO] ? 1 : 0; } } #if MAX_HWIFS > 1 /* * save_match() is used to simplify logic in init_irq() below. * * A loophole here is that we may not know about a particular * hwif's irq until after that hwif is actually probed/initialized.. * This could be a problem for the case where an hwif is on a * dual interface that requires serialization (eg. cmd640) and another * hwif using one of the same irqs is initialized beforehand. * * This routine detects and reports such situations, but does not fix them. */ static void save_match(ide_hwif_t *hwif, ide_hwif_t *new, ide_hwif_t **match) { ide_hwif_t *m = *match; if (m && m->hwgroup && m->hwgroup != new->hwgroup) { if (!new->hwgroup) return; printk(KERN_WARNING "%s: potential IRQ problem with %s and %s\n", hwif->name, new->name, m->name); } if (!m || m->irq != hwif->irq) /* don't undo a prior perfect match */ *match = new; } #endif /* MAX_HWIFS > 1 */ /* * init request queue */ static int ide_init_queue(ide_drive_t *drive) { struct request_queue *q; ide_hwif_t *hwif = HWIF(drive); int max_sectors = 256; int max_sg_entries = PRD_ENTRIES; /* * Our default set up assumes the normal IDE case, * that is 64K segmenting, standard PRD setup * and LBA28. Some drivers then impose their own * limits and LBA48 we could raise it but as yet * do not. */ q = blk_init_queue_node(do_ide_request, &ide_lock, hwif_to_node(hwif)); if (!q) return 1; q->queuedata = drive; blk_queue_segment_boundary(q, 0xffff); if (hwif->rqsize < max_sectors) max_sectors = hwif->rqsize; blk_queue_max_sectors(q, max_sectors); #ifdef CONFIG_PCI /* When we have an IOMMU, we may have a problem where pci_map_sg() * creates segments that don't completely match our boundary * requirements and thus need to be broken up again. Because it * doesn't align properly either, we may actually have to break up * to more segments than what was we got in the first place, a max * worst case is twice as many. * This will be fixed once we teach pci_map_sg() about our boundary * requirements, hopefully soon. *FIXME* */ if (!PCI_DMA_BUS_IS_PHYS) max_sg_entries >>= 1; #endif /* CONFIG_PCI */ blk_queue_max_hw_segments(q, max_sg_entries); blk_queue_max_phys_segments(q, max_sg_entries); /* assign drive queue */ drive->queue = q; /* needs drive->queue to be set */ ide_toggle_bounce(drive, 1); return 0; } static void ide_add_drive_to_hwgroup(ide_drive_t *drive) { ide_hwgroup_t *hwgroup = drive->hwif->hwgroup; spin_lock_irq(&ide_lock); if (!hwgroup->drive) { /* first drive for hwgroup. */ drive->next = drive; hwgroup->drive = drive; hwgroup->hwif = HWIF(hwgroup->drive); } else { drive->next = hwgroup->drive->next; hwgroup->drive->next = drive; } spin_unlock_irq(&ide_lock); } /* * For any present drive: * - allocate the block device queue * - link drive into the hwgroup */ static void ide_port_setup_devices(ide_hwif_t *hwif) { int i; mutex_lock(&ide_cfg_mtx); for (i = 0; i < MAX_DRIVES; i++) { ide_drive_t *drive = &hwif->drives[i]; if (!drive->present) continue; if (ide_init_queue(drive)) { printk(KERN_ERR "ide: failed to init %s\n", drive->name); continue; } ide_add_drive_to_hwgroup(drive); } mutex_unlock(&ide_cfg_mtx); } static ide_hwif_t *ide_ports[MAX_HWIFS]; void ide_remove_port_from_hwgroup(ide_hwif_t *hwif) { ide_hwgroup_t *hwgroup = hwif->hwgroup; ide_ports[hwif->index] = NULL; spin_lock_irq(&ide_lock); /* * Remove us from the hwgroup, and free * the hwgroup if we were the only member */ if (hwif->next == hwif) { BUG_ON(hwgroup->hwif != hwif); kfree(hwgroup); } else { /* There is another interface in hwgroup. * Unlink us, and set hwgroup->drive and ->hwif to * something sane. */ ide_hwif_t *g = hwgroup->hwif; while (g->next != hwif) g = g->next; g->next = hwif->next; if (hwgroup->hwif == hwif) { /* Chose a random hwif for hwgroup->hwif. * It's guaranteed that there are no drives * left in the hwgroup. */ BUG_ON(hwgroup->drive != NULL); hwgroup->hwif = g; } BUG_ON(hwgroup->hwif == hwif); } spin_unlock_irq(&ide_lock); } /* * This routine sets up the irq for an ide interface, and creates a new * hwgroup for the irq/hwif if none was previously assigned. * * Much of the code is for correctly detecting/handling irq sharing * and irq serialization situations. This is somewhat complex because * it handles static as well as dynamic (PCMCIA) IDE interfaces. */ static int init_irq (ide_hwif_t *hwif) { struct ide_io_ports *io_ports = &hwif->io_ports; unsigned int index; ide_hwgroup_t *hwgroup; ide_hwif_t *match = NULL; mutex_lock(&ide_cfg_mtx); hwif->hwgroup = NULL; #if MAX_HWIFS > 1 /* * Group up with any other hwifs that share our irq(s). */ for (index = 0; index < MAX_HWIFS; index++) { ide_hwif_t *h = ide_ports[index]; if (h && h->hwgroup) { /* scan only initialized ports */ if (hwif->irq == h->irq) { hwif->sharing_irq = h->sharing_irq = 1; if (hwif->chipset != ide_pci || h->chipset != ide_pci) { save_match(hwif, h, &match); } } if (hwif->serialized) { if (hwif->mate && hwif->mate->irq == h->irq) save_match(hwif, h, &match); } if (h->serialized) { if (h->mate && hwif->irq == h->mate->irq) save_match(hwif, h, &match); } } } #endif /* MAX_HWIFS > 1 */ /* * If we are still without a hwgroup, then form a new one */ if (match) { hwgroup = match->hwgroup; hwif->hwgroup = hwgroup; /* * Link us into the hwgroup. * This must be done early, do ensure that unexpected_intr * can find the hwif and prevent irq storms. * No drives are attached to the new hwif, choose_drive * can't do anything stupid (yet). * Add ourself as the 2nd entry to the hwgroup->hwif * linked list, the first entry is the hwif that owns * hwgroup->handler - do not change that. */ spin_lock_irq(&ide_lock); hwif->next = hwgroup->hwif->next; hwgroup->hwif->next = hwif; BUG_ON(hwif->next == hwif); spin_unlock_irq(&ide_lock); } else { hwgroup = kmalloc_node(sizeof(*hwgroup), GFP_KERNEL|__GFP_ZERO, hwif_to_node(hwif)); if (hwgroup == NULL) goto out_up; hwif->hwgroup = hwgroup; hwgroup->hwif = hwif->next = hwif; init_timer(&hwgroup->timer); hwgroup->timer.function = &ide_timer_expiry; hwgroup->timer.data = (unsigned long) hwgroup; } ide_ports[hwif->index] = hwif; /* * Allocate the irq, if not already obtained for another hwif */ if (!match || match->irq != hwif->irq) { int sa = 0; #if defined(__mc68000__) sa = IRQF_SHARED; #endif /* __mc68000__ */ if (hwif->chipset == ide_pci || hwif->chipset == ide_cmd646 || hwif->chipset == ide_ali14xx) sa = IRQF_SHARED; if (io_ports->ctl_addr) hwif->tp_ops->set_irq(hwif, 1); if (request_irq(hwif->irq,&ide_intr,sa,hwif->name,hwgroup)) goto out_unlink; } if (!hwif->rqsize) { if ((hwif->host_flags & IDE_HFLAG_NO_LBA48) || (hwif->host_flags & IDE_HFLAG_NO_LBA48_DMA)) hwif->rqsize = 256; else hwif->rqsize = 65536; } #if !defined(__mc68000__) printk(KERN_INFO "%s at 0x%03lx-0x%03lx,0x%03lx on irq %d", hwif->name, io_ports->data_addr, io_ports->status_addr, io_ports->ctl_addr, hwif->irq); #else printk(KERN_INFO "%s at 0x%08lx on irq %d", hwif->name, io_ports->data_addr, hwif->irq); #endif /* __mc68000__ */ if (match) printk(KERN_CONT " (%sed with %s)", hwif->sharing_irq ? "shar" : "serializ", match->name); printk(KERN_CONT "\n"); mutex_unlock(&ide_cfg_mtx); return 0; out_unlink: ide_remove_port_from_hwgroup(hwif); out_up: mutex_unlock(&ide_cfg_mtx); return 1; } static int ata_lock(dev_t dev, void *data) { /* FIXME: we want to pin hwif down */ return 0; } static struct kobject *ata_probe(dev_t dev, int *part, void *data) { ide_hwif_t *hwif = data; int unit = *part >> PARTN_BITS; ide_drive_t *drive = &hwif->drives[unit]; if (!drive->present) return NULL; if (drive->media == ide_disk) request_module("ide-disk"); if (drive->scsi) request_module("ide-scsi"); if (drive->media == ide_cdrom || drive->media == ide_optical) request_module("ide-cd"); if (drive->media == ide_tape) request_module("ide-tape"); if (drive->media == ide_floppy) request_module("ide-floppy"); return NULL; } static struct kobject *exact_match(dev_t dev, int *part, void *data) { struct gendisk *p = data; *part &= (1 << PARTN_BITS) - 1; return &disk_to_dev(p)->kobj; } static int exact_lock(dev_t dev, void *data) { struct gendisk *p = data; if (!get_disk(p)) return -1; return 0; } void ide_register_region(struct gendisk *disk) { blk_register_region(MKDEV(disk->major, disk->first_minor), disk->minors, NULL, exact_match, exact_lock, disk); } EXPORT_SYMBOL_GPL(ide_register_region); void ide_unregister_region(struct gendisk *disk) { blk_unregister_region(MKDEV(disk->major, disk->first_minor), disk->minors); } EXPORT_SYMBOL_GPL(ide_unregister_region); void ide_init_disk(struct gendisk *disk, ide_drive_t *drive) { ide_hwif_t *hwif = drive->hwif; unsigned int unit = (drive->select.all >> 4) & 1; disk->major = hwif->major; disk->first_minor = unit << PARTN_BITS; sprintf(disk->disk_name, "hd%c", 'a' + hwif->index * MAX_DRIVES + unit); disk->queue = drive->queue; } EXPORT_SYMBOL_GPL(ide_init_disk); static void ide_remove_drive_from_hwgroup(ide_drive_t *drive) { ide_hwgroup_t *hwgroup = drive->hwif->hwgroup; if (drive == drive->next) { /* special case: last drive from hwgroup. */ BUG_ON(hwgroup->drive != drive); hwgroup->drive = NULL; } else { ide_drive_t *walk; walk = hwgroup->drive; while (walk->next != drive) walk = walk->next; walk->next = drive->next; if (hwgroup->drive == drive) { hwgroup->drive = drive->next; hwgroup->hwif = hwgroup->drive->hwif; } } BUG_ON(hwgroup->drive == drive); } static void drive_release_dev (struct device *dev) { ide_drive_t *drive = container_of(dev, ide_drive_t, gendev); ide_proc_unregister_device(drive); spin_lock_irq(&ide_lock); ide_remove_drive_from_hwgroup(drive); kfree(drive->id); drive->id = NULL; drive->present = 0; /* Messed up locking ... */ spin_unlock_irq(&ide_lock); blk_cleanup_queue(drive->queue); spin_lock_irq(&ide_lock); drive->queue = NULL; spin_unlock_irq(&ide_lock); complete(&drive->gendev_rel_comp); } static int hwif_init(ide_hwif_t *hwif) { int old_irq; if (!hwif->irq) { hwif->irq = __ide_default_irq(hwif->io_ports.data_addr); if (!hwif->irq) { printk(KERN_ERR "%s: disabled, no IRQ\n", hwif->name); return 0; } } if (register_blkdev(hwif->major, hwif->name)) return 0; if (!hwif->sg_max_nents) hwif->sg_max_nents = PRD_ENTRIES; hwif->sg_table = kmalloc(sizeof(struct scatterlist)*hwif->sg_max_nents, GFP_KERNEL); if (!hwif->sg_table) { printk(KERN_ERR "%s: unable to allocate SG table.\n", hwif->name); goto out; } sg_init_table(hwif->sg_table, hwif->sg_max_nents); if (init_irq(hwif) == 0) goto done; old_irq = hwif->irq; /* * It failed to initialise. Find the default IRQ for * this port and try that. */ hwif->irq = __ide_default_irq(hwif->io_ports.data_addr); if (!hwif->irq) { printk(KERN_ERR "%s: disabled, unable to get IRQ %d\n", hwif->name, old_irq); goto out; } if (init_irq(hwif)) { printk(KERN_ERR "%s: probed IRQ %d and default IRQ %d failed\n", hwif->name, old_irq, hwif->irq); goto out; } printk(KERN_WARNING "%s: probed IRQ %d failed, using default\n", hwif->name, hwif->irq); done: blk_register_region(MKDEV(hwif->major, 0), MAX_DRIVES << PARTN_BITS, THIS_MODULE, ata_probe, ata_lock, hwif); return 1; out: unregister_blkdev(hwif->major, hwif->name); return 0; } static void hwif_register_devices(ide_hwif_t *hwif) { unsigned int i; for (i = 0; i < MAX_DRIVES; i++) { ide_drive_t *drive = &hwif->drives[i]; struct device *dev = &drive->gendev; int ret; if (!drive->present) continue; snprintf(dev->bus_id, BUS_ID_SIZE, "%u.%u", hwif->index, i); dev->parent = &hwif->gendev; dev->bus = &ide_bus_type; dev->driver_data = drive; dev->release = drive_release_dev; ret = device_register(dev); if (ret < 0) printk(KERN_WARNING "IDE: %s: device_register error: " "%d\n", __func__, ret); } } static void ide_port_init_devices(ide_hwif_t *hwif) { const struct ide_port_ops *port_ops = hwif->port_ops; int i; for (i = 0; i < MAX_DRIVES; i++) { ide_drive_t *drive = &hwif->drives[i]; if (hwif->host_flags & IDE_HFLAG_IO_32BIT) drive->io_32bit = 1; if (hwif->host_flags & IDE_HFLAG_UNMASK_IRQS) drive->unmask = 1; if (hwif->host_flags & IDE_HFLAG_NO_UNMASK_IRQS) drive->no_unmask = 1; if (port_ops && port_ops->init_dev) port_ops->init_dev(drive); } } static void ide_init_port(ide_hwif_t *hwif, unsigned int port, const struct ide_port_info *d) { hwif->channel = port; if (d->chipset) hwif->chipset = d->chipset; if (d->init_iops) d->init_iops(hwif); if ((!hwif->irq && (d->host_flags & IDE_HFLAG_LEGACY_IRQS)) || (d->host_flags & IDE_HFLAG_FORCE_LEGACY_IRQS)) hwif->irq = port ? 15 : 14; /* ->host_flags may be set by ->init_iops (or even earlier...) */ hwif->host_flags |= d->host_flags; hwif->pio_mask = d->pio_mask; if (d->tp_ops) hwif->tp_ops = d->tp_ops; /* ->set_pio_mode for DTC2278 is currently limited to port 0 */ if (hwif->chipset != ide_dtc2278 || hwif->channel == 0) hwif->port_ops = d->port_ops; hwif->swdma_mask = d->swdma_mask; hwif->mwdma_mask = d->mwdma_mask; hwif->ultra_mask = d->udma_mask; if ((d->host_flags & IDE_HFLAG_NO_DMA) == 0) { int rc; if (d->init_dma) rc = d->init_dma(hwif, d); else rc = ide_hwif_setup_dma(hwif, d); if (rc < 0) { printk(KERN_INFO "%s: DMA disabled\n", hwif->name); hwif->dma_base = 0; hwif->swdma_mask = 0; hwif->mwdma_mask = 0; hwif->ultra_mask = 0; } else if (d->dma_ops) hwif->dma_ops = d->dma_ops; } if ((d->host_flags & IDE_HFLAG_SERIALIZE) || ((d->host_flags & IDE_HFLAG_SERIALIZE_DMA) && hwif->dma_base)) { if (hwif->mate) hwif->mate->serialized = hwif->serialized = 1; } if (d->host_flags & IDE_HFLAG_RQSIZE_256) hwif->rqsize = 256; /* call chipset specific routine for each enabled port */ if (d->init_hwif) d->init_hwif(hwif); } static void ide_port_cable_detect(ide_hwif_t *hwif) { const struct ide_port_ops *port_ops = hwif->port_ops; if (port_ops && port_ops->cable_detect && (hwif->ultra_mask & 0x78)) { if (hwif->cbl != ATA_CBL_PATA40_SHORT) hwif->cbl = port_ops->cable_detect(hwif); } } static ssize_t store_delete_devices(struct device *portdev, struct device_attribute *attr, const char *buf, size_t n) { ide_hwif_t *hwif = dev_get_drvdata(portdev); if (strncmp(buf, "1", n)) return -EINVAL; ide_port_unregister_devices(hwif); return n; }; static DEVICE_ATTR(delete_devices, S_IWUSR, NULL, store_delete_devices); static ssize_t store_scan(struct device *portdev, struct device_attribute *attr, const char *buf, size_t n) { ide_hwif_t *hwif = dev_get_drvdata(portdev); if (strncmp(buf, "1", n)) return -EINVAL; ide_port_unregister_devices(hwif); ide_port_scan(hwif); return n; }; static DEVICE_ATTR(scan, S_IWUSR, NULL, store_scan); static struct device_attribute *ide_port_attrs[] = { &dev_attr_delete_devices, &dev_attr_scan, NULL }; static int ide_sysfs_register_port(ide_hwif_t *hwif) { int i, uninitialized_var(rc); for (i = 0; ide_port_attrs[i]; i++) { rc = device_create_file(hwif->portdev, ide_port_attrs[i]); if (rc) break; } return rc; } static unsigned int ide_indexes; /** * ide_find_port_slot - find free port slot * @d: IDE port info * * Return the new port slot index or -ENOENT if we are out of free slots. */ static int ide_find_port_slot(const struct ide_port_info *d) { int idx = -ENOENT; u8 bootable = (d && (d->host_flags & IDE_HFLAG_NON_BOOTABLE)) ? 0 : 1; u8 i = (d && (d->host_flags & IDE_HFLAG_QD_2ND_PORT)) ? 1 : 0;; /* * Claim an unassigned slot. * * Give preference to claiming other slots before claiming ide0/ide1, * just in case there's another interface yet-to-be-scanned * which uses ports 0x1f0/0x170 (the ide0/ide1 defaults). * * Unless there is a bootable card that does not use the standard * ports 0x1f0/0x170 (the ide0/ide1 defaults). */ mutex_lock(&ide_cfg_mtx); if (MAX_HWIFS == 1) { if (ide_indexes == 0 && i == 0) idx = 1; } else { if (bootable) { if ((ide_indexes | i) != (1 << MAX_HWIFS) - 1) idx = ffz(ide_indexes | i); } else { if ((ide_indexes | 3) != (1 << MAX_HWIFS) - 1) idx = ffz(ide_indexes | 3); else if ((ide_indexes & 3) != 3) idx = ffz(ide_indexes); } } if (idx >= 0) ide_indexes |= (1 << idx); mutex_unlock(&ide_cfg_mtx); return idx; } static void ide_free_port_slot(int idx) { mutex_lock(&ide_cfg_mtx); ide_indexes &= ~(1 << idx); mutex_unlock(&ide_cfg_mtx); } struct ide_host *ide_host_alloc_all(const struct ide_port_info *d, hw_regs_t **hws) { struct ide_host *host; int i; host = kzalloc(sizeof(*host), GFP_KERNEL); if (host == NULL) return NULL; for (i = 0; i < MAX_HWIFS; i++) { ide_hwif_t *hwif; int idx; if (hws[i] == NULL) continue; hwif = kzalloc(sizeof(*hwif), GFP_KERNEL); if (hwif == NULL) continue; idx = ide_find_port_slot(d); if (idx < 0) { printk(KERN_ERR "%s: no free slot for interface\n", d ? d->name : "ide"); kfree(hwif); continue; } ide_init_port_data(hwif, idx); hwif->host = host; host->ports[i] = hwif; host->n_ports++; } if (host->n_ports == 0) { kfree(host); return NULL; } if (hws[0]) host->dev[0] = hws[0]->dev; if (d) host->host_flags = d->host_flags; return host; } EXPORT_SYMBOL_GPL(ide_host_alloc_all); struct ide_host *ide_host_alloc(const struct ide_port_info *d, hw_regs_t **hws) { hw_regs_t *hws_all[MAX_HWIFS]; int i; for (i = 0; i < MAX_HWIFS; i++) hws_all[i] = (i < 4) ? hws[i] : NULL; return ide_host_alloc_all(d, hws_all); } EXPORT_SYMBOL_GPL(ide_host_alloc); int ide_host_register(struct ide_host *host, const struct ide_port_info *d, hw_regs_t **hws) { ide_hwif_t *hwif, *mate = NULL; int i, j = 0; for (i = 0; i < MAX_HWIFS; i++) { hwif = host->ports[i]; if (hwif == NULL) { mate = NULL; continue; } ide_init_port_hw(hwif, hws[i]); ide_port_apply_params(hwif); if (d == NULL) { mate = NULL; continue; } if ((i & 1) && mate) { hwif->mate = mate; mate->mate = hwif; } mate = (i & 1) ? NULL : hwif; ide_init_port(hwif, i & 1, d); ide_port_cable_detect(hwif); ide_port_init_devices(hwif); } for (i = 0; i < MAX_HWIFS; i++) { hwif = host->ports[i]; if (hwif == NULL) continue; if (ide_probe_port(hwif) == 0) hwif->present = 1; if (hwif->chipset != ide_4drives || !hwif->mate || !hwif->mate->present) ide_register_port(hwif); if (hwif->present) ide_port_tune_devices(hwif); } for (i = 0; i < MAX_HWIFS; i++) { hwif = host->ports[i]; if (hwif == NULL) continue; if (hwif_init(hwif) == 0) { printk(KERN_INFO "%s: failed to initialize IDE " "interface\n", hwif->name); hwif->present = 0; continue; } j++; if (hwif->present) ide_port_setup_devices(hwif); ide_acpi_init(hwif); if (hwif->present) ide_acpi_port_init_devices(hwif); } for (i = 0; i < MAX_HWIFS; i++) { hwif = host->ports[i]; if (hwif == NULL) continue; if (hwif->chipset == ide_unknown) hwif->chipset = ide_generic; if (hwif->present) hwif_register_devices(hwif); } for (i = 0; i < MAX_HWIFS; i++) { hwif = host->ports[i]; if (hwif == NULL) continue; ide_sysfs_register_port(hwif); ide_proc_register_port(hwif); if (hwif->present) ide_proc_port_register_devices(hwif); } return j ? 0 : -1; } EXPORT_SYMBOL_GPL(ide_host_register); int ide_host_add(const struct ide_port_info *d, hw_regs_t **hws, struct ide_host **hostp) { struct ide_host *host; int rc; host = ide_host_alloc(d, hws); if (host == NULL) return -ENOMEM; rc = ide_host_register(host, d, hws); if (rc) { ide_host_free(host); return rc; } if (hostp) *hostp = host; return 0; } EXPORT_SYMBOL_GPL(ide_host_add); void ide_host_free(struct ide_host *host) { ide_hwif_t *hwif; int i; for (i = 0; i < MAX_HWIFS; i++) { hwif = host->ports[i]; if (hwif == NULL) continue; ide_free_port_slot(hwif->index); kfree(hwif); } kfree(host); } EXPORT_SYMBOL_GPL(ide_host_free); void ide_host_remove(struct ide_host *host) { int i; for (i = 0; i < MAX_HWIFS; i++) { if (host->ports[i]) ide_unregister(host->ports[i]); } ide_host_free(host); } EXPORT_SYMBOL_GPL(ide_host_remove); void ide_port_scan(ide_hwif_t *hwif) { ide_port_apply_params(hwif); ide_port_cable_detect(hwif); ide_port_init_devices(hwif); if (ide_probe_port(hwif) < 0) return; hwif->present = 1; ide_port_tune_devices(hwif); ide_acpi_port_init_devices(hwif); ide_port_setup_devices(hwif); hwif_register_devices(hwif); ide_proc_port_register_devices(hwif); } EXPORT_SYMBOL_GPL(ide_port_scan); static void ide_legacy_init_one(hw_regs_t **hws, hw_regs_t *hw, u8 port_no, const struct ide_port_info *d, unsigned long config) { unsigned long base, ctl; int irq; if (port_no == 0) { base = 0x1f0; ctl = 0x3f6; irq = 14; } else { base = 0x170; ctl = 0x376; irq = 15; } if (!request_region(base, 8, d->name)) { printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n", d->name, base, base + 7); return; } if (!request_region(ctl, 1, d->name)) { printk(KERN_ERR "%s: I/O resource 0x%lX not free.\n", d->name, ctl); release_region(base, 8); return; } ide_std_init_ports(hw, base, ctl); hw->irq = irq; hw->chipset = d->chipset; hw->config = config; hws[port_no] = hw; } int ide_legacy_device_add(const struct ide_port_info *d, unsigned long config) { hw_regs_t hw[2], *hws[] = { NULL, NULL, NULL, NULL }; memset(&hw, 0, sizeof(hw)); if ((d->host_flags & IDE_HFLAG_QD_2ND_PORT) == 0) ide_legacy_init_one(hws, &hw[0], 0, d, config); ide_legacy_init_one(hws, &hw[1], 1, d, config); if (hws[0] == NULL && hws[1] == NULL && (d->host_flags & IDE_HFLAG_SINGLE)) return -ENOENT; return ide_host_add(d, hws, NULL); } EXPORT_SYMBOL_GPL(ide_legacy_device_add);