/* * Copyright (C) 1998-2000 Andre Hedrick * Copyright (C) 1995-1998 Mark Lord * Copyright (C) 2007 Bartlomiej Zolnierkiewicz * * May be copied or modified under the terms of the GNU General Public License */ #include #include #include #include #include #include #include #include /** * ide_setup_pci_baseregs - place a PCI IDE controller native * @dev: PCI device of interface to switch native * @name: Name of interface * * We attempt to place the PCI interface into PCI native mode. If * we succeed the BARs are ok and the controller is in PCI mode. * Returns 0 on success or an errno code. * * FIXME: if we program the interface and then fail to set the BARS * we don't switch it back to legacy mode. Do we actually care ?? */ static int ide_setup_pci_baseregs(struct pci_dev *dev, const char *name) { u8 progif = 0; /* * Place both IDE interfaces into PCI "native" mode: */ if (pci_read_config_byte(dev, PCI_CLASS_PROG, &progif) || (progif & 5) != 5) { if ((progif & 0xa) != 0xa) { printk(KERN_INFO "%s: device not capable of full " "native PCI mode\n", name); return -EOPNOTSUPP; } printk("%s: placing both ports into native PCI mode\n", name); (void) pci_write_config_byte(dev, PCI_CLASS_PROG, progif|5); if (pci_read_config_byte(dev, PCI_CLASS_PROG, &progif) || (progif & 5) != 5) { printk(KERN_ERR "%s: rewrite of PROGIF failed, wanted " "0x%04x, got 0x%04x\n", name, progif|5, progif); return -EOPNOTSUPP; } } return 0; } #ifdef CONFIG_BLK_DEV_IDEDMA_PCI static void ide_pci_clear_simplex(unsigned long dma_base, const char *name) { u8 dma_stat = inb(dma_base + 2); outb(dma_stat & 0x60, dma_base + 2); dma_stat = inb(dma_base + 2); if (dma_stat & 0x80) printk(KERN_INFO "%s: simplex device: DMA forced\n", name); } /** * ide_pci_dma_base - setup BMIBA * @hwif: IDE interface * @d: IDE port info * * Fetch the DMA Bus-Master-I/O-Base-Address (BMIBA) from PCI space. */ unsigned long ide_pci_dma_base(ide_hwif_t *hwif, const struct ide_port_info *d) { struct pci_dev *dev = to_pci_dev(hwif->dev); unsigned long dma_base = 0; if (hwif->host_flags & IDE_HFLAG_MMIO) return hwif->dma_base; if (hwif->mate && hwif->mate->dma_base) { dma_base = hwif->mate->dma_base - (hwif->channel ? 0 : 8); } else { u8 baridx = (d->host_flags & IDE_HFLAG_CS5520) ? 2 : 4; dma_base = pci_resource_start(dev, baridx); if (dma_base == 0) { printk(KERN_ERR "%s: DMA base is invalid\n", d->name); return 0; } } if (hwif->channel) dma_base += 8; return dma_base; } EXPORT_SYMBOL_GPL(ide_pci_dma_base); int ide_pci_check_simplex(ide_hwif_t *hwif, const struct ide_port_info *d) { u8 dma_stat; if (d->host_flags & (IDE_HFLAG_MMIO | IDE_HFLAG_CS5520)) goto out; if (d->host_flags & IDE_HFLAG_CLEAR_SIMPLEX) { ide_pci_clear_simplex(hwif->dma_base, d->name); goto out; } /* * If the device claims "simplex" DMA, this means that only one of * the two interfaces can be trusted with DMA at any point in time * (so we should enable DMA only on one of the two interfaces). * * FIXME: At this point we haven't probed the drives so we can't make * the appropriate decision. Really we should defer this problem until * we tune the drive then try to grab DMA ownership if we want to be * the DMA end. This has to be become dynamic to handle hot-plug. */ dma_stat = hwif->tp_ops->read_sff_dma_status(hwif); if ((dma_stat & 0x80) && hwif->mate && hwif->mate->dma_base) { printk(KERN_INFO "%s: simplex device: DMA disabled\n", d->name); return -1; } out: return 0; } EXPORT_SYMBOL_GPL(ide_pci_check_simplex); /* * Set up BM-DMA capability (PnP BIOS should have done this) */ int ide_pci_set_master(struct pci_dev *dev, const char *name) { u16 pcicmd; pci_read_config_word(dev, PCI_COMMAND, &pcicmd); if ((pcicmd & PCI_COMMAND_MASTER) == 0) { pci_set_master(dev); if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd) || (pcicmd & PCI_COMMAND_MASTER) == 0) { printk(KERN_ERR "%s: error updating PCICMD on %s\n", name, pci_name(dev)); return -EIO; } } return 0; } EXPORT_SYMBOL_GPL(ide_pci_set_master); #endif /* CONFIG_BLK_DEV_IDEDMA_PCI */ void ide_setup_pci_noise(struct pci_dev *dev, const struct ide_port_info *d) { printk(KERN_INFO "%s: IDE controller (0x%04x:0x%04x rev 0x%02x) at " " PCI slot %s\n", d->name, dev->vendor, dev->device, dev->revision, pci_name(dev)); } EXPORT_SYMBOL_GPL(ide_setup_pci_noise); /** * ide_pci_enable - do PCI enables * @dev: PCI device * @d: IDE port info * * Enable the IDE PCI device. We attempt to enable the device in full * but if that fails then we only need IO space. The PCI code should * have setup the proper resources for us already for controllers in * legacy mode. * * Returns zero on success or an error code */ static int ide_pci_enable(struct pci_dev *dev, const struct ide_port_info *d) { int ret, bars; if (pci_enable_device(dev)) { ret = pci_enable_device_io(dev); if (ret < 0) { printk(KERN_WARNING "%s: (ide_setup_pci_device:) " "Could not enable device.\n", d->name); goto out; } printk(KERN_WARNING "%s: BIOS configuration fixed.\n", d->name); } /* * assume all devices can do 32-bit DMA for now, we can add * a DMA mask field to the struct ide_port_info if we need it * (or let lower level driver set the DMA mask) */ ret = pci_set_dma_mask(dev, DMA_32BIT_MASK); if (ret < 0) { printk(KERN_ERR "%s: can't set dma mask\n", d->name); goto out; } if (d->host_flags & IDE_HFLAG_SINGLE) bars = (1 << 2) - 1; else bars = (1 << 4) - 1; if ((d->host_flags & IDE_HFLAG_NO_DMA) == 0) { if (d->host_flags & IDE_HFLAG_CS5520) bars |= (1 << 2); else bars |= (1 << 4); } ret = pci_request_selected_regions(dev, bars, d->name); if (ret < 0) printk(KERN_ERR "%s: can't reserve resources\n", d->name); out: return ret; } /** * ide_pci_configure - configure an unconfigured device * @dev: PCI device * @d: IDE port info * * Enable and configure the PCI device we have been passed. * Returns zero on success or an error code. */ static int ide_pci_configure(struct pci_dev *dev, const struct ide_port_info *d) { u16 pcicmd = 0; /* * PnP BIOS was *supposed* to have setup this device, but we * can do it ourselves, so long as the BIOS has assigned an IRQ * (or possibly the device is using a "legacy header" for IRQs). * Maybe the user deliberately *disabled* the device, * but we'll eventually ignore it again if no drives respond. */ if (ide_setup_pci_baseregs(dev, d->name) || pci_write_config_word(dev, PCI_COMMAND, pcicmd | PCI_COMMAND_IO)) { printk(KERN_INFO "%s: device disabled (BIOS)\n", d->name); return -ENODEV; } if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd)) { printk(KERN_ERR "%s: error accessing PCI regs\n", d->name); return -EIO; } if (!(pcicmd & PCI_COMMAND_IO)) { printk(KERN_ERR "%s: unable to enable IDE controller\n", d->name); return -ENXIO; } return 0; } /** * ide_pci_check_iomem - check a register is I/O * @dev: PCI device * @d: IDE port info * @bar: BAR number * * Checks if a BAR is configured and points to MMIO space. If so, * return an error code. Otherwise return 0 */ static int ide_pci_check_iomem(struct pci_dev *dev, const struct ide_port_info *d, int bar) { ulong flags = pci_resource_flags(dev, bar); /* Unconfigured ? */ if (!flags || pci_resource_len(dev, bar) == 0) return 0; /* I/O space */ if (flags & IORESOURCE_IO) return 0; /* Bad */ return -EINVAL; } /** * ide_hw_configure - configure a hw_regs_t instance * @dev: PCI device holding interface * @d: IDE port info * @port: port number * @irq: PCI IRQ * @hw: hw_regs_t instance corresponding to this port * * Perform the initial set up for the hardware interface structure. This * is done per interface port rather than per PCI device. There may be * more than one port per device. * * Returns zero on success or an error code. */ static int ide_hw_configure(struct pci_dev *dev, const struct ide_port_info *d, unsigned int port, int irq, hw_regs_t *hw) { unsigned long ctl = 0, base = 0; if ((d->host_flags & IDE_HFLAG_ISA_PORTS) == 0) { if (ide_pci_check_iomem(dev, d, 2 * port) || ide_pci_check_iomem(dev, d, 2 * port + 1)) { printk(KERN_ERR "%s: I/O baseregs (BIOS) are reported " "as MEM for port %d!\n", d->name, port); return -EINVAL; } ctl = pci_resource_start(dev, 2*port+1); base = pci_resource_start(dev, 2*port); } else { /* Use default values */ ctl = port ? 0x374 : 0x3f4; base = port ? 0x170 : 0x1f0; } if (!base || !ctl) { printk(KERN_ERR "%s: bad PCI BARs for port %d, skipping\n", d->name, port); return -EINVAL; } memset(hw, 0, sizeof(*hw)); hw->irq = irq; hw->dev = &dev->dev; hw->chipset = d->chipset ? d->chipset : ide_pci; ide_std_init_ports(hw, base, ctl | 2); return 0; } #ifdef CONFIG_BLK_DEV_IDEDMA_PCI /** * ide_hwif_setup_dma - configure DMA interface * @hwif: IDE interface * @d: IDE port info * * Set up the DMA base for the interface. Enable the master bits as * necessary and attempt to bring the device DMA into a ready to use * state */ int ide_hwif_setup_dma(ide_hwif_t *hwif, const struct ide_port_info *d) { struct pci_dev *dev = to_pci_dev(hwif->dev); if ((d->host_flags & IDE_HFLAG_NO_AUTODMA) == 0 || ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE && (dev->class & 0x80))) { unsigned long base = ide_pci_dma_base(hwif, d); if (base == 0) return -1; hwif->dma_base = base; if (ide_pci_check_simplex(hwif, d) < 0) return -1; if (ide_pci_set_master(dev, d->name) < 0) return -1; if (hwif->host_flags & IDE_HFLAG_MMIO) printk(KERN_INFO " %s: MMIO-DMA\n", hwif->name); else printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n", hwif->name, base, base + 7); hwif->extra_base = base + (hwif->channel ? 8 : 16); if (ide_allocate_dma_engine(hwif)) return -1; hwif->dma_ops = &sff_dma_ops; } return 0; } #endif /* CONFIG_BLK_DEV_IDEDMA_PCI */ /** * ide_setup_pci_controller - set up IDE PCI * @dev: PCI device * @d: IDE port info * @noisy: verbose flag * @config: returned as 1 if we configured the hardware * * Set up the PCI and controller side of the IDE interface. This brings * up the PCI side of the device, checks that the device is enabled * and enables it if need be */ static int ide_setup_pci_controller(struct pci_dev *dev, const struct ide_port_info *d, int noisy, int *config) { int ret; u16 pcicmd; if (noisy) ide_setup_pci_noise(dev, d); ret = ide_pci_enable(dev, d); if (ret < 0) goto out; ret = pci_read_config_word(dev, PCI_COMMAND, &pcicmd); if (ret < 0) { printk(KERN_ERR "%s: error accessing PCI regs\n", d->name); goto out; } if (!(pcicmd & PCI_COMMAND_IO)) { /* is device disabled? */ ret = ide_pci_configure(dev, d); if (ret < 0) goto out; *config = 1; printk(KERN_INFO "%s: device enabled (Linux)\n", d->name); } out: return ret; } /** * ide_pci_setup_ports - configure ports/devices on PCI IDE * @dev: PCI device * @d: IDE port info * @pciirq: IRQ line * @hw: hw_regs_t instances corresponding to this PCI IDE device * @hws: hw_regs_t pointers table to update * * Scan the interfaces attached to this device and do any * necessary per port setup. Attach the devices and ask the * generic DMA layer to do its work for us. * * Normally called automaticall from do_ide_pci_setup_device, * but is also used directly as a helper function by some controllers * where the chipset setup is not the default PCI IDE one. */ void ide_pci_setup_ports(struct pci_dev *dev, const struct ide_port_info *d, int pciirq, hw_regs_t *hw, hw_regs_t **hws) { int channels = (d->host_flags & IDE_HFLAG_SINGLE) ? 1 : 2, port; u8 tmp; /* * Set up the IDE ports */ for (port = 0; port < channels; ++port) { const ide_pci_enablebit_t *e = &(d->enablebits[port]); if (e->reg && (pci_read_config_byte(dev, e->reg, &tmp) || (tmp & e->mask) != e->val)) { printk(KERN_INFO "%s: IDE port disabled\n", d->name); continue; /* port not enabled */ } if (ide_hw_configure(dev, d, port, pciirq, hw + port)) continue; *(hws + port) = hw + port; } } EXPORT_SYMBOL_GPL(ide_pci_setup_ports); /* * ide_setup_pci_device() looks at the primary/secondary interfaces * on a PCI IDE device and, if they are enabled, prepares the IDE driver * for use with them. This generic code works for most PCI chipsets. * * One thing that is not standardized is the location of the * primary/secondary interface "enable/disable" bits. For chipsets that * we "know" about, this information is in the struct ide_port_info; * for all other chipsets, we just assume both interfaces are enabled. */ static int do_ide_setup_pci_device(struct pci_dev *dev, const struct ide_port_info *d, u8 noisy) { int tried_config = 0; int pciirq, ret; ret = ide_setup_pci_controller(dev, d, noisy, &tried_config); if (ret < 0) goto out; /* * Can we trust the reported IRQ? */ pciirq = dev->irq; /* * This allows offboard ide-pci cards the enable a BIOS, * verify interrupt settings of split-mirror pci-config * space, place chipset into init-mode, and/or preserve * an interrupt if the card is not native ide support. */ ret = d->init_chipset ? d->init_chipset(dev, d->name) : 0; if (ret < 0) goto out; /* Is it an "IDE storage" device in non-PCI mode? */ if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE && (dev->class & 5) != 5) { if (noisy) printk(KERN_INFO "%s: not 100%% native mode: " "will probe irqs later\n", d->name); pciirq = ret; } else if (tried_config) { if (noisy) printk(KERN_INFO "%s: will probe irqs later\n", d->name); pciirq = 0; } else if (!pciirq) { if (noisy) printk(KERN_WARNING "%s: bad irq (%d): will probe later\n", d->name, pciirq); pciirq = 0; } else { if (noisy) printk(KERN_INFO "%s: 100%% native mode on irq %d\n", d->name, pciirq); } ret = pciirq; out: return ret; } int ide_setup_pci_device(struct pci_dev *dev, const struct ide_port_info *d) { hw_regs_t hw[4], *hws[] = { NULL, NULL, NULL, NULL }; int ret; ret = do_ide_setup_pci_device(dev, d, 1); if (ret >= 0) { /* FIXME: silent failure can happen */ ide_pci_setup_ports(dev, d, ret, &hw[0], &hws[0]); ret = ide_host_add(d, hws, NULL); } return ret; } EXPORT_SYMBOL_GPL(ide_setup_pci_device); int ide_setup_pci_devices(struct pci_dev *dev1, struct pci_dev *dev2, const struct ide_port_info *d) { struct pci_dev *pdev[] = { dev1, dev2 }; int ret, i; hw_regs_t hw[4], *hws[] = { NULL, NULL, NULL, NULL }; for (i = 0; i < 2; i++) { ret = do_ide_setup_pci_device(pdev[i], d, !i); /* * FIXME: Mom, mom, they stole me the helper function to undo * do_ide_setup_pci_device() on the first device! */ if (ret < 0) goto out; /* FIXME: silent failure can happen */ ide_pci_setup_ports(pdev[i], d, ret, &hw[i*2], &hws[i*2]); } ret = ide_host_add(d, hws, NULL); out: return ret; } EXPORT_SYMBOL_GPL(ide_setup_pci_devices);