/* * linux/drivers/mmc/core/core.c * * Copyright (C) 2003-2004 Russell King, All Rights Reserved. * SD support Copyright (C) 2004 Ian Molton, All Rights Reserved. * Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved. * MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "core.h" #include "bus.h" #include "host.h" #include "sdio_bus.h" #include "mmc_ops.h" #include "sd_ops.h" #include "sdio_ops.h" /* If the device is not responding */ #define MMC_CORE_TIMEOUT_MS (10 * 60 * 1000) /* 10 minute timeout */ /* * Background operations can take a long time, depending on the housekeeping * operations the card has to perform. */ #define MMC_BKOPS_MAX_TIMEOUT (4 * 60 * 1000) /* max time to wait in ms */ static struct workqueue_struct *workqueue; static const unsigned freqs[] = { 400000, 300000, 200000, 100000 }; /* * Enabling software CRCs on the data blocks can be a significant (30%) * performance cost, and for other reasons may not always be desired. * So we allow it it to be disabled. */ bool use_spi_crc = 1; module_param(use_spi_crc, bool, 0); /* * Internal function. Schedule delayed work in the MMC work queue. */ static int mmc_schedule_delayed_work(struct delayed_work *work, unsigned long delay) { return queue_delayed_work(workqueue, work, delay); } /* * Internal function. Flush all scheduled work from the MMC work queue. */ static void mmc_flush_scheduled_work(void) { flush_workqueue(workqueue); } #ifdef CONFIG_FAIL_MMC_REQUEST /* * Internal function. Inject random data errors. * If mmc_data is NULL no errors are injected. */ static void mmc_should_fail_request(struct mmc_host *host, struct mmc_request *mrq) { struct mmc_command *cmd = mrq->cmd; struct mmc_data *data = mrq->data; static const int data_errors[] = { -ETIMEDOUT, -EILSEQ, -EIO, }; if (!data) return; if (cmd->error || data->error || !should_fail(&host->fail_mmc_request, data->blksz * data->blocks)) return; data->error = data_errors[prandom_u32() % ARRAY_SIZE(data_errors)]; data->bytes_xfered = (prandom_u32() % (data->bytes_xfered >> 9)) << 9; } #else /* CONFIG_FAIL_MMC_REQUEST */ static inline void mmc_should_fail_request(struct mmc_host *host, struct mmc_request *mrq) { } #endif /* CONFIG_FAIL_MMC_REQUEST */ /** * mmc_request_done - finish processing an MMC request * @host: MMC host which completed request * @mrq: MMC request which request * * MMC drivers should call this function when they have completed * their processing of a request. */ void mmc_request_done(struct mmc_host *host, struct mmc_request *mrq) { struct mmc_command *cmd = mrq->cmd; int err = cmd->error; if (err && cmd->retries && mmc_host_is_spi(host)) { if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND) cmd->retries = 0; } if (err && cmd->retries && !mmc_card_removed(host->card)) { /* * Request starter must handle retries - see * mmc_wait_for_req_done(). */ if (mrq->done) mrq->done(mrq); } else { mmc_should_fail_request(host, mrq); led_trigger_event(host->led, LED_OFF); pr_debug("%s: req done (CMD%u): %d: %08x %08x %08x %08x\n", mmc_hostname(host), cmd->opcode, err, cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]); if (mrq->data) { pr_debug("%s: %d bytes transferred: %d\n", mmc_hostname(host), mrq->data->bytes_xfered, mrq->data->error); } if (mrq->stop) { pr_debug("%s: (CMD%u): %d: %08x %08x %08x %08x\n", mmc_hostname(host), mrq->stop->opcode, mrq->stop->error, mrq->stop->resp[0], mrq->stop->resp[1], mrq->stop->resp[2], mrq->stop->resp[3]); } if (mrq->done) mrq->done(mrq); mmc_host_clk_release(host); } } EXPORT_SYMBOL(mmc_request_done); static void mmc_start_request(struct mmc_host *host, struct mmc_request *mrq) { #ifdef CONFIG_MMC_DEBUG unsigned int i, sz; struct scatterlist *sg; #endif if (mrq->sbc) { pr_debug("<%s: starting CMD%u arg %08x flags %08x>\n", mmc_hostname(host), mrq->sbc->opcode, mrq->sbc->arg, mrq->sbc->flags); } pr_debug("%s: starting CMD%u arg %08x flags %08x\n", mmc_hostname(host), mrq->cmd->opcode, mrq->cmd->arg, mrq->cmd->flags); if (mrq->data) { pr_debug("%s: blksz %d blocks %d flags %08x " "tsac %d ms nsac %d\n", mmc_hostname(host), mrq->data->blksz, mrq->data->blocks, mrq->data->flags, mrq->data->timeout_ns / 1000000, mrq->data->timeout_clks); } if (mrq->stop) { pr_debug("%s: CMD%u arg %08x flags %08x\n", mmc_hostname(host), mrq->stop->opcode, mrq->stop->arg, mrq->stop->flags); } WARN_ON(!host->claimed); mrq->cmd->error = 0; mrq->cmd->mrq = mrq; if (mrq->data) { BUG_ON(mrq->data->blksz > host->max_blk_size); BUG_ON(mrq->data->blocks > host->max_blk_count); BUG_ON(mrq->data->blocks * mrq->data->blksz > host->max_req_size); #ifdef CONFIG_MMC_DEBUG sz = 0; for_each_sg(mrq->data->sg, sg, mrq->data->sg_len, i) sz += sg->length; BUG_ON(sz != mrq->data->blocks * mrq->data->blksz); #endif mrq->cmd->data = mrq->data; mrq->data->error = 0; mrq->data->mrq = mrq; if (mrq->stop) { mrq->data->stop = mrq->stop; mrq->stop->error = 0; mrq->stop->mrq = mrq; } } mmc_host_clk_hold(host); led_trigger_event(host->led, LED_FULL); host->ops->request(host, mrq); } /** * mmc_start_bkops - start BKOPS for supported cards * @card: MMC card to start BKOPS * @form_exception: A flag to indicate if this function was * called due to an exception raised by the card * * Start background operations whenever requested. * When the urgent BKOPS bit is set in a R1 command response * then background operations should be started immediately. */ void mmc_start_bkops(struct mmc_card *card, bool from_exception) { int err; int timeout; bool use_busy_signal; BUG_ON(!card); if (!card->ext_csd.bkops_en || mmc_card_doing_bkops(card)) return; err = mmc_read_bkops_status(card); if (err) { pr_err("%s: Failed to read bkops status: %d\n", mmc_hostname(card->host), err); return; } if (!card->ext_csd.raw_bkops_status) return; if (card->ext_csd.raw_bkops_status < EXT_CSD_BKOPS_LEVEL_2 && from_exception) return; mmc_claim_host(card->host); if (card->ext_csd.raw_bkops_status >= EXT_CSD_BKOPS_LEVEL_2) { timeout = MMC_BKOPS_MAX_TIMEOUT; use_busy_signal = true; } else { timeout = 0; use_busy_signal = false; } err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_BKOPS_START, 1, timeout, use_busy_signal, true, false); if (err) { pr_warn("%s: Error %d starting bkops\n", mmc_hostname(card->host), err); goto out; } /* * For urgent bkops status (LEVEL_2 and more) * bkops executed synchronously, otherwise * the operation is in progress */ if (!use_busy_signal) mmc_card_set_doing_bkops(card); out: mmc_release_host(card->host); } EXPORT_SYMBOL(mmc_start_bkops); /* * mmc_wait_data_done() - done callback for data request * @mrq: done data request * * Wakes up mmc context, passed as a callback to host controller driver */ static void mmc_wait_data_done(struct mmc_request *mrq) { mrq->host->context_info.is_done_rcv = true; wake_up_interruptible(&mrq->host->context_info.wait); } static void mmc_wait_done(struct mmc_request *mrq) { complete(&mrq->completion); } /* *__mmc_start_data_req() - starts data request * @host: MMC host to start the request * @mrq: data request to start * * Sets the done callback to be called when request is completed by the card. * Starts data mmc request execution */ static int __mmc_start_data_req(struct mmc_host *host, struct mmc_request *mrq) { mrq->done = mmc_wait_data_done; mrq->host = host; if (mmc_card_removed(host->card)) { mrq->cmd->error = -ENOMEDIUM; mmc_wait_data_done(mrq); return -ENOMEDIUM; } mmc_start_request(host, mrq); return 0; } static int __mmc_start_req(struct mmc_host *host, struct mmc_request *mrq) { init_completion(&mrq->completion); mrq->done = mmc_wait_done; if (mmc_card_removed(host->card)) { mrq->cmd->error = -ENOMEDIUM; complete(&mrq->completion); return -ENOMEDIUM; } mmc_start_request(host, mrq); return 0; } /* * mmc_wait_for_data_req_done() - wait for request completed * @host: MMC host to prepare the command. * @mrq: MMC request to wait for * * Blocks MMC context till host controller will ack end of data request * execution or new request notification arrives from the block layer. * Handles command retries. * * Returns enum mmc_blk_status after checking errors. */ static int mmc_wait_for_data_req_done(struct mmc_host *host, struct mmc_request *mrq, struct mmc_async_req *next_req) { struct mmc_command *cmd; struct mmc_context_info *context_info = &host->context_info; int err; unsigned long flags; while (1) { wait_event_interruptible(context_info->wait, (context_info->is_done_rcv || context_info->is_new_req)); spin_lock_irqsave(&context_info->lock, flags); context_info->is_waiting_last_req = false; spin_unlock_irqrestore(&context_info->lock, flags); if (context_info->is_done_rcv) { context_info->is_done_rcv = false; context_info->is_new_req = false; cmd = mrq->cmd; if (!cmd->error || !cmd->retries || mmc_card_removed(host->card)) { err = host->areq->err_check(host->card, host->areq); break; /* return err */ } else { pr_info("%s: req failed (CMD%u): %d, retrying...\n", mmc_hostname(host), cmd->opcode, cmd->error); cmd->retries--; cmd->error = 0; host->ops->request(host, mrq); continue; /* wait for done/new event again */ } } else if (context_info->is_new_req) { context_info->is_new_req = false; if (!next_req) { err = MMC_BLK_NEW_REQUEST; break; /* return err */ } } } return err; } static void mmc_wait_for_req_done(struct mmc_host *host, struct mmc_request *mrq) { struct mmc_command *cmd; while (1) { wait_for_completion(&mrq->completion); cmd = mrq->cmd; /* * If host has timed out waiting for the sanitize * to complete, card might be still in programming state * so let's try to bring the card out of programming * state. */ if (cmd->sanitize_busy && cmd->error == -ETIMEDOUT) { if (!mmc_interrupt_hpi(host->card)) { pr_warning("%s: %s: Interrupted sanitize\n", mmc_hostname(host), __func__); cmd->error = 0; break; } else { pr_err("%s: %s: Failed to interrupt sanitize\n", mmc_hostname(host), __func__); } } if (!cmd->error || !cmd->retries || mmc_card_removed(host->card)) break; pr_debug("%s: req failed (CMD%u): %d, retrying...\n", mmc_hostname(host), cmd->opcode, cmd->error); cmd->retries--; cmd->error = 0; host->ops->request(host, mrq); } } /** * mmc_pre_req - Prepare for a new request * @host: MMC host to prepare command * @mrq: MMC request to prepare for * @is_first_req: true if there is no previous started request * that may run in parellel to this call, otherwise false * * mmc_pre_req() is called in prior to mmc_start_req() to let * host prepare for the new request. Preparation of a request may be * performed while another request is running on the host. */ static void mmc_pre_req(struct mmc_host *host, struct mmc_request *mrq, bool is_first_req) { if (host->ops->pre_req) { mmc_host_clk_hold(host); host->ops->pre_req(host, mrq, is_first_req); mmc_host_clk_release(host); } } /** * mmc_post_req - Post process a completed request * @host: MMC host to post process command * @mrq: MMC request to post process for * @err: Error, if non zero, clean up any resources made in pre_req * * Let the host post process a completed request. Post processing of * a request may be performed while another reuqest is running. */ static void mmc_post_req(struct mmc_host *host, struct mmc_request *mrq, int err) { if (host->ops->post_req) { mmc_host_clk_hold(host); host->ops->post_req(host, mrq, err); mmc_host_clk_release(host); } } /** * mmc_start_req - start a non-blocking request * @host: MMC host to start command * @areq: async request to start * @error: out parameter returns 0 for success, otherwise non zero * * Start a new MMC custom command request for a host. * If there is on ongoing async request wait for completion * of that request and start the new one and return. * Does not wait for the new request to complete. * * Returns the completed request, NULL in case of none completed. * Wait for the an ongoing request (previoulsy started) to complete and * return the completed request. If there is no ongoing request, NULL * is returned without waiting. NULL is not an error condition. */ struct mmc_async_req *mmc_start_req(struct mmc_host *host, struct mmc_async_req *areq, int *error) { int err = 0; int start_err = 0; struct mmc_async_req *data = host->areq; /* Prepare a new request */ if (areq) mmc_pre_req(host, areq->mrq, !host->areq); if (host->areq) { err = mmc_wait_for_data_req_done(host, host->areq->mrq, areq); if (err == MMC_BLK_NEW_REQUEST) { if (error) *error = err; /* * The previous request was not completed, * nothing to return */ return NULL; } /* * Check BKOPS urgency for each R1 response */ if (host->card && mmc_card_mmc(host->card) && ((mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1) || (mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1B)) && (host->areq->mrq->cmd->resp[0] & R1_EXCEPTION_EVENT)) mmc_start_bkops(host->card, true); } if (!err && areq) start_err = __mmc_start_data_req(host, areq->mrq); if (host->areq) mmc_post_req(host, host->areq->mrq, 0); /* Cancel a prepared request if it was not started. */ if ((err || start_err) && areq) mmc_post_req(host, areq->mrq, -EINVAL); if (err) host->areq = NULL; else host->areq = areq; if (error) *error = err; return data; } EXPORT_SYMBOL(mmc_start_req); /** * mmc_wait_for_req - start a request and wait for completion * @host: MMC host to start command * @mrq: MMC request to start * * Start a new MMC custom command request for a host, and wait * for the command to complete. Does not attempt to parse the * response. */ void mmc_wait_for_req(struct mmc_host *host, struct mmc_request *mrq) { __mmc_start_req(host, mrq); mmc_wait_for_req_done(host, mrq); } EXPORT_SYMBOL(mmc_wait_for_req); /** * mmc_interrupt_hpi - Issue for High priority Interrupt * @card: the MMC card associated with the HPI transfer * * Issued High Priority Interrupt, and check for card status * until out-of prg-state. */ int mmc_interrupt_hpi(struct mmc_card *card) { int err; u32 status; unsigned long prg_wait; BUG_ON(!card); if (!card->ext_csd.hpi_en) { pr_info("%s: HPI enable bit unset\n", mmc_hostname(card->host)); return 1; } mmc_claim_host(card->host); err = mmc_send_status(card, &status); if (err) { pr_err("%s: Get card status fail\n", mmc_hostname(card->host)); goto out; } switch (R1_CURRENT_STATE(status)) { case R1_STATE_IDLE: case R1_STATE_READY: case R1_STATE_STBY: case R1_STATE_TRAN: /* * In idle and transfer states, HPI is not needed and the caller * can issue the next intended command immediately */ goto out; case R1_STATE_PRG: break; default: /* In all other states, it's illegal to issue HPI */ pr_debug("%s: HPI cannot be sent. Card state=%d\n", mmc_hostname(card->host), R1_CURRENT_STATE(status)); err = -EINVAL; goto out; } err = mmc_send_hpi_cmd(card, &status); if (err) goto out; prg_wait = jiffies + msecs_to_jiffies(card->ext_csd.out_of_int_time); do { err = mmc_send_status(card, &status); if (!err && R1_CURRENT_STATE(status) == R1_STATE_TRAN) break; if (time_after(jiffies, prg_wait)) err = -ETIMEDOUT; } while (!err); out: mmc_release_host(card->host); return err; } EXPORT_SYMBOL(mmc_interrupt_hpi); /** * mmc_wait_for_cmd - start a command and wait for completion * @host: MMC host to start command * @cmd: MMC command to start * @retries: maximum number of retries * * Start a new MMC command for a host, and wait for the command * to complete. Return any error that occurred while the command * was executing. Do not attempt to parse the response. */ int mmc_wait_for_cmd(struct mmc_host *host, struct mmc_command *cmd, int retries) { struct mmc_request mrq = {NULL}; WARN_ON(!host->claimed); memset(cmd->resp, 0, sizeof(cmd->resp)); cmd->retries = retries; mrq.cmd = cmd; cmd->data = NULL; mmc_wait_for_req(host, &mrq); return cmd->error; } EXPORT_SYMBOL(mmc_wait_for_cmd); /** * mmc_stop_bkops - stop ongoing BKOPS * @card: MMC card to check BKOPS * * Send HPI command to stop ongoing background operations to * allow rapid servicing of foreground operations, e.g. read/ * writes. Wait until the card comes out of the programming state * to avoid errors in servicing read/write requests. */ int mmc_stop_bkops(struct mmc_card *card) { int err = 0; BUG_ON(!card); err = mmc_interrupt_hpi(card); /* * If err is EINVAL, we can't issue an HPI. * It should complete the BKOPS. */ if (!err || (err == -EINVAL)) { mmc_card_clr_doing_bkops(card); err = 0; } return err; } EXPORT_SYMBOL(mmc_stop_bkops); int mmc_read_bkops_status(struct mmc_card *card) { int err; u8 *ext_csd; /* * In future work, we should consider storing the entire ext_csd. */ ext_csd = kmalloc(512, GFP_KERNEL); if (!ext_csd) { pr_err("%s: could not allocate buffer to receive the ext_csd.\n", mmc_hostname(card->host)); return -ENOMEM; } mmc_claim_host(card->host); err = mmc_send_ext_csd(card, ext_csd); mmc_release_host(card->host); if (err) goto out; card->ext_csd.raw_bkops_status = ext_csd[EXT_CSD_BKOPS_STATUS]; card->ext_csd.raw_exception_status = ext_csd[EXT_CSD_EXP_EVENTS_STATUS]; out: kfree(ext_csd); return err; } EXPORT_SYMBOL(mmc_read_bkops_status); /** * mmc_set_data_timeout - set the timeout for a data command * @data: data phase for command * @card: the MMC card associated with the data transfer * * Computes the data timeout parameters according to the * correct algorithm given the card type. */ void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card) { unsigned int mult; /* * SDIO cards only define an upper 1 s limit on access. */ if (mmc_card_sdio(card)) { data->timeout_ns = 1000000000; data->timeout_clks = 0; return; } /* * SD cards use a 100 multiplier rather than 10 */ mult = mmc_card_sd(card) ? 100 : 10; /* * Scale up the multiplier (and therefore the timeout) by * the r2w factor for writes. */ if (data->flags & MMC_DATA_WRITE) mult <<= card->csd.r2w_factor; data->timeout_ns = card->csd.tacc_ns * mult; data->timeout_clks = card->csd.tacc_clks * mult; /* * SD cards also have an upper limit on the timeout. */ if (mmc_card_sd(card)) { unsigned int timeout_us, limit_us; timeout_us = data->timeout_ns / 1000; if (mmc_host_clk_rate(card->host)) timeout_us += data->timeout_clks * 1000 / (mmc_host_clk_rate(card->host) / 1000); if (data->flags & MMC_DATA_WRITE) /* * The MMC spec "It is strongly recommended * for hosts to implement more than 500ms * timeout value even if the card indicates * the 250ms maximum busy length." Even the * previous value of 300ms is known to be * insufficient for some cards. */ limit_us = 3000000; else limit_us = 100000; /* * SDHC cards always use these fixed values. */ if (timeout_us > limit_us || mmc_card_blockaddr(card)) { data->timeout_ns = limit_us * 1000; data->timeout_clks = 0; } } /* * Some cards require longer data read timeout than indicated in CSD. * Address this by setting the read timeout to a "reasonably high" * value. For the cards tested, 300ms has proven enough. If necessary, * this value can be increased if other problematic cards require this. */ if (mmc_card_long_read_time(card) && data->flags & MMC_DATA_READ) { data->timeout_ns = 300000000; data->timeout_clks = 0; } /* * Some cards need very high timeouts if driven in SPI mode. * The worst observed timeout was 900ms after writing a * continuous stream of data until the internal logic * overflowed. */ if (mmc_host_is_spi(card->host)) { if (data->flags & MMC_DATA_WRITE) { if (data->timeout_ns < 1000000000) data->timeout_ns = 1000000000; /* 1s */ } else { if (data->timeout_ns < 100000000) data->timeout_ns = 100000000; /* 100ms */ } } } EXPORT_SYMBOL(mmc_set_data_timeout); /** * mmc_align_data_size - pads a transfer size to a more optimal value * @card: the MMC card associated with the data transfer * @sz: original transfer size * * Pads the original data size with a number of extra bytes in * order to avoid controller bugs and/or performance hits * (e.g. some controllers revert to PIO for certain sizes). * * Returns the improved size, which might be unmodified. * * Note that this function is only relevant when issuing a * single scatter gather entry. */ unsigned int mmc_align_data_size(struct mmc_card *card, unsigned int sz) { /* * FIXME: We don't have a system for the controller to tell * the core about its problems yet, so for now we just 32-bit * align the size. */ sz = ((sz + 3) / 4) * 4; return sz; } EXPORT_SYMBOL(mmc_align_data_size); /** * __mmc_claim_host - exclusively claim a host * @host: mmc host to claim * @abort: whether or not the operation should be aborted * * Claim a host for a set of operations. If @abort is non null and * dereference a non-zero value then this will return prematurely with * that non-zero value without acquiring the lock. Returns zero * with the lock held otherwise. */ int __mmc_claim_host(struct mmc_host *host, atomic_t *abort) { DECLARE_WAITQUEUE(wait, current); unsigned long flags; int stop; might_sleep(); add_wait_queue(&host->wq, &wait); spin_lock_irqsave(&host->lock, flags); while (1) { set_current_state(TASK_UNINTERRUPTIBLE); stop = abort ? atomic_read(abort) : 0; if (stop || !host->claimed || host->claimer == current) break; spin_unlock_irqrestore(&host->lock, flags); schedule(); spin_lock_irqsave(&host->lock, flags); } set_current_state(TASK_RUNNING); if (!stop) { host->claimed = 1; host->claimer = current; host->claim_cnt += 1; } else wake_up(&host->wq); spin_unlock_irqrestore(&host->lock, flags); remove_wait_queue(&host->wq, &wait); if (host->ops->enable && !stop && host->claim_cnt == 1) host->ops->enable(host); return stop; } EXPORT_SYMBOL(__mmc_claim_host); /** * mmc_release_host - release a host * @host: mmc host to release * * Release a MMC host, allowing others to claim the host * for their operations. */ void mmc_release_host(struct mmc_host *host) { unsigned long flags; WARN_ON(!host->claimed); if (host->ops->disable && host->claim_cnt == 1) host->ops->disable(host); spin_lock_irqsave(&host->lock, flags); if (--host->claim_cnt) { /* Release for nested claim */ spin_unlock_irqrestore(&host->lock, flags); } else { host->claimed = 0; host->claimer = NULL; spin_unlock_irqrestore(&host->lock, flags); wake_up(&host->wq); } } EXPORT_SYMBOL(mmc_release_host); /* * This is a helper function, which fetches a runtime pm reference for the * card device and also claims the host. */ void mmc_get_card(struct mmc_card *card) { pm_runtime_get_sync(&card->dev); mmc_claim_host(card->host); } EXPORT_SYMBOL(mmc_get_card); /* * This is a helper function, which releases the host and drops the runtime * pm reference for the card device. */ void mmc_put_card(struct mmc_card *card) { mmc_release_host(card->host); pm_runtime_mark_last_busy(&card->dev); pm_runtime_put_autosuspend(&card->dev); } EXPORT_SYMBOL(mmc_put_card); /* * Internal function that does the actual ios call to the host driver, * optionally printing some debug output. */ static inline void mmc_set_ios(struct mmc_host *host) { struct mmc_ios *ios = &host->ios; pr_debug("%s: clock %uHz busmode %u powermode %u cs %u Vdd %u " "width %u timing %u\n", mmc_hostname(host), ios->clock, ios->bus_mode, ios->power_mode, ios->chip_select, ios->vdd, ios->bus_width, ios->timing); if (ios->clock > 0) mmc_set_ungated(host); host->ops->set_ios(host, ios); } /* * Control chip select pin on a host. */ void mmc_set_chip_select(struct mmc_host *host, int mode) { mmc_host_clk_hold(host); host->ios.chip_select = mode; mmc_set_ios(host); mmc_host_clk_release(host); } /* * Sets the host clock to the highest possible frequency that * is below "hz". */ static void __mmc_set_clock(struct mmc_host *host, unsigned int hz) { WARN_ON(hz < host->f_min); if (hz > host->f_max) hz = host->f_max; host->ios.clock = hz; mmc_set_ios(host); } void mmc_set_clock(struct mmc_host *host, unsigned int hz) { mmc_host_clk_hold(host); __mmc_set_clock(host, hz); mmc_host_clk_release(host); } #ifdef CONFIG_MMC_CLKGATE /* * This gates the clock by setting it to 0 Hz. */ void mmc_gate_clock(struct mmc_host *host) { unsigned long flags; spin_lock_irqsave(&host->clk_lock, flags); host->clk_old = host->ios.clock; host->ios.clock = 0; host->clk_gated = true; spin_unlock_irqrestore(&host->clk_lock, flags); mmc_set_ios(host); } /* * This restores the clock from gating by using the cached * clock value. */ void mmc_ungate_clock(struct mmc_host *host) { /* * We should previously have gated the clock, so the clock shall * be 0 here! The clock may however be 0 during initialization, * when some request operations are performed before setting * the frequency. When ungate is requested in that situation * we just ignore the call. */ if (host->clk_old) { BUG_ON(host->ios.clock); /* This call will also set host->clk_gated to false */ __mmc_set_clock(host, host->clk_old); } } void mmc_set_ungated(struct mmc_host *host) { unsigned long flags; /* * We've been given a new frequency while the clock is gated, * so make sure we regard this as ungating it. */ spin_lock_irqsave(&host->clk_lock, flags); host->clk_gated = false; spin_unlock_irqrestore(&host->clk_lock, flags); } #else void mmc_set_ungated(struct mmc_host *host) { } #endif /* * Change the bus mode (open drain/push-pull) of a host. */ void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode) { mmc_host_clk_hold(host); host->ios.bus_mode = mode; mmc_set_ios(host); mmc_host_clk_release(host); } /* * Change data bus width of a host. */ void mmc_set_bus_width(struct mmc_host *host, unsigned int width) { mmc_host_clk_hold(host); host->ios.bus_width = width; mmc_set_ios(host); mmc_host_clk_release(host); } /** * mmc_vdd_to_ocrbitnum - Convert a voltage to the OCR bit number * @vdd: voltage (mV) * @low_bits: prefer low bits in boundary cases * * This function returns the OCR bit number according to the provided @vdd * value. If conversion is not possible a negative errno value returned. * * Depending on the @low_bits flag the function prefers low or high OCR bits * on boundary voltages. For example, * with @low_bits = true, 3300 mV translates to ilog2(MMC_VDD_32_33); * with @low_bits = false, 3300 mV translates to ilog2(MMC_VDD_33_34); * * Any value in the [1951:1999] range translates to the ilog2(MMC_VDD_20_21). */ static int mmc_vdd_to_ocrbitnum(int vdd, bool low_bits) { const int max_bit = ilog2(MMC_VDD_35_36); int bit; if (vdd < 1650 || vdd > 3600) return -EINVAL; if (vdd >= 1650 && vdd <= 1950) return ilog2(MMC_VDD_165_195); if (low_bits) vdd -= 1; /* Base 2000 mV, step 100 mV, bit's base 8. */ bit = (vdd - 2000) / 100 + 8; if (bit > max_bit) return max_bit; return bit; } /** * mmc_vddrange_to_ocrmask - Convert a voltage range to the OCR mask * @vdd_min: minimum voltage value (mV) * @vdd_max: maximum voltage value (mV) * * This function returns the OCR mask bits according to the provided @vdd_min * and @vdd_max values. If conversion is not possible the function returns 0. * * Notes wrt boundary cases: * This function sets the OCR bits for all boundary voltages, for example * [3300:3400] range is translated to MMC_VDD_32_33 | MMC_VDD_33_34 | * MMC_VDD_34_35 mask. */ u32 mmc_vddrange_to_ocrmask(int vdd_min, int vdd_max) { u32 mask = 0; if (vdd_max < vdd_min) return 0; /* Prefer high bits for the boundary vdd_max values. */ vdd_max = mmc_vdd_to_ocrbitnum(vdd_max, false); if (vdd_max < 0) return 0; /* Prefer low bits for the boundary vdd_min values. */ vdd_min = mmc_vdd_to_ocrbitnum(vdd_min, true); if (vdd_min < 0) return 0; /* Fill the mask, from max bit to min bit. */ while (vdd_max >= vdd_min) mask |= 1 << vdd_max--; return mask; } EXPORT_SYMBOL(mmc_vddrange_to_ocrmask); #ifdef CONFIG_OF /** * mmc_of_parse_voltage - return mask of supported voltages * @np: The device node need to be parsed. * @mask: mask of voltages available for MMC/SD/SDIO * * 1. Return zero on success. * 2. Return negative errno: voltage-range is invalid. */ int mmc_of_parse_voltage(struct device_node *np, u32 *mask) { const u32 *voltage_ranges; int num_ranges, i; voltage_ranges = of_get_property(np, "voltage-ranges", &num_ranges); num_ranges = num_ranges / sizeof(*voltage_ranges) / 2; if (!voltage_ranges || !num_ranges) { pr_info("%s: voltage-ranges unspecified\n", np->full_name); return -EINVAL; } for (i = 0; i < num_ranges; i++) { const int j = i * 2; u32 ocr_mask; ocr_mask = mmc_vddrange_to_ocrmask( be32_to_cpu(voltage_ranges[j]), be32_to_cpu(voltage_ranges[j + 1])); if (!ocr_mask) { pr_err("%s: voltage-range #%d is invalid\n", np->full_name, i); return -EINVAL; } *mask |= ocr_mask; } return 0; } EXPORT_SYMBOL(mmc_of_parse_voltage); #endif /* CONFIG_OF */ #ifdef CONFIG_REGULATOR /** * mmc_regulator_get_ocrmask - return mask of supported voltages * @supply: regulator to use * * This returns either a negative errno, or a mask of voltages that * can be provided to MMC/SD/SDIO devices using the specified voltage * regulator. This would normally be called before registering the * MMC host adapter. */ int mmc_regulator_get_ocrmask(struct regulator *supply) { int result = 0; int count; int i; count = regulator_count_voltages(supply); if (count < 0) return count; for (i = 0; i < count; i++) { int vdd_uV; int vdd_mV; vdd_uV = regulator_list_voltage(supply, i); if (vdd_uV <= 0) continue; vdd_mV = vdd_uV / 1000; result |= mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV); } return result; } EXPORT_SYMBOL_GPL(mmc_regulator_get_ocrmask); /** * mmc_regulator_set_ocr - set regulator to match host->ios voltage * @mmc: the host to regulate * @supply: regulator to use * @vdd_bit: zero for power off, else a bit number (host->ios.vdd) * * Returns zero on success, else negative errno. * * MMC host drivers may use this to enable or disable a regulator using * a particular supply voltage. This would normally be called from the * set_ios() method. */ int mmc_regulator_set_ocr(struct mmc_host *mmc, struct regulator *supply, unsigned short vdd_bit) { int result = 0; int min_uV, max_uV; if (vdd_bit) { int tmp; int voltage; /* * REVISIT mmc_vddrange_to_ocrmask() may have set some * bits this regulator doesn't quite support ... don't * be too picky, most cards and regulators are OK with * a 0.1V range goof (it's a small error percentage). */ tmp = vdd_bit - ilog2(MMC_VDD_165_195); if (tmp == 0) { min_uV = 1650 * 1000; max_uV = 1950 * 1000; } else { min_uV = 1900 * 1000 + tmp * 100 * 1000; max_uV = min_uV + 100 * 1000; } /* * If we're using a fixed/static regulator, don't call * regulator_set_voltage; it would fail. */ voltage = regulator_get_voltage(supply); if (!regulator_can_change_voltage(supply)) min_uV = max_uV = voltage; if (voltage < 0) result = voltage; else if (voltage < min_uV || voltage > max_uV) result = regulator_set_voltage(supply, min_uV, max_uV); else result = 0; if (result == 0 && !mmc->regulator_enabled) { result = regulator_enable(supply); if (!result) mmc->regulator_enabled = true; } } else if (mmc->regulator_enabled) { result = regulator_disable(supply); if (result == 0) mmc->regulator_enabled = false; } if (result) dev_err(mmc_dev(mmc), "could not set regulator OCR (%d)\n", result); return result; } EXPORT_SYMBOL_GPL(mmc_regulator_set_ocr); int mmc_regulator_get_supply(struct mmc_host *mmc) { struct device *dev = mmc_dev(mmc); struct regulator *supply; int ret; supply = devm_regulator_get(dev, "vmmc"); mmc->supply.vmmc = supply; mmc->supply.vqmmc = devm_regulator_get_optional(dev, "vqmmc"); if (IS_ERR(supply)) return PTR_ERR(supply); ret = mmc_regulator_get_ocrmask(supply); if (ret > 0) mmc->ocr_avail = ret; else dev_warn(mmc_dev(mmc), "Failed getting OCR mask: %d\n", ret); return 0; } EXPORT_SYMBOL_GPL(mmc_regulator_get_supply); #endif /* CONFIG_REGULATOR */ /* * Mask off any voltages we don't support and select * the lowest voltage */ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr) { int bit; /* * Sanity check the voltages that the card claims to * support. */ if (ocr & 0x7F) { dev_warn(mmc_dev(host), "card claims to support voltages below defined range\n"); ocr &= ~0x7F; } ocr &= host->ocr_avail; if (!ocr) { dev_warn(mmc_dev(host), "no support for card's volts\n"); return 0; } if (host->caps2 & MMC_CAP2_FULL_PWR_CYCLE) { bit = ffs(ocr) - 1; ocr &= 3 << bit; mmc_power_cycle(host, ocr); } else { bit = fls(ocr) - 1; ocr &= 3 << bit; if (bit != host->ios.vdd) dev_warn(mmc_dev(host), "exceeding card's volts\n"); } return ocr; } int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage) { int err = 0; int old_signal_voltage = host->ios.signal_voltage; host->ios.signal_voltage = signal_voltage; if (host->ops->start_signal_voltage_switch) { mmc_host_clk_hold(host); err = host->ops->start_signal_voltage_switch(host, &host->ios); mmc_host_clk_release(host); } if (err) host->ios.signal_voltage = old_signal_voltage; return err; } int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr) { struct mmc_command cmd = {0}; int err = 0; u32 clock; BUG_ON(!host); /* * Send CMD11 only if the request is to switch the card to * 1.8V signalling. */ if (signal_voltage == MMC_SIGNAL_VOLTAGE_330) return __mmc_set_signal_voltage(host, signal_voltage); /* * If we cannot switch voltages, return failure so the caller * can continue without UHS mode */ if (!host->ops->start_signal_voltage_switch) return -EPERM; if (!host->ops->card_busy) pr_warning("%s: cannot verify signal voltage switch\n", mmc_hostname(host)); cmd.opcode = SD_SWITCH_VOLTAGE; cmd.arg = 0; cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; err = mmc_wait_for_cmd(host, &cmd, 0); if (err) return err; if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) return -EIO; mmc_host_clk_hold(host); /* * The card should drive cmd and dat[0:3] low immediately * after the response of cmd11, but wait 1 ms to be sure */ mmc_delay(1); if (host->ops->card_busy && !host->ops->card_busy(host)) { err = -EAGAIN; goto power_cycle; } /* * During a signal voltage level switch, the clock must be gated * for 5 ms according to the SD spec */ clock = host->ios.clock; host->ios.clock = 0; mmc_set_ios(host); if (__mmc_set_signal_voltage(host, signal_voltage)) { /* * Voltages may not have been switched, but we've already * sent CMD11, so a power cycle is required anyway */ err = -EAGAIN; goto power_cycle; } /* Keep clock gated for at least 5 ms */ mmc_delay(5); host->ios.clock = clock; mmc_set_ios(host); /* Wait for at least 1 ms according to spec */ mmc_delay(1); /* * Failure to switch is indicated by the card holding * dat[0:3] low */ if (host->ops->card_busy && host->ops->card_busy(host)) err = -EAGAIN; power_cycle: if (err) { pr_debug("%s: Signal voltage switch failed, " "power cycling card\n", mmc_hostname(host)); mmc_power_cycle(host, ocr); } mmc_host_clk_release(host); return err; } /* * Select timing parameters for host. */ void mmc_set_timing(struct mmc_host *host, unsigned int timing) { mmc_host_clk_hold(host); host->ios.timing = timing; mmc_set_ios(host); mmc_host_clk_release(host); } /* * Select appropriate driver type for host. */ void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type) { mmc_host_clk_hold(host); host->ios.drv_type = drv_type; mmc_set_ios(host); mmc_host_clk_release(host); } /* * Apply power to the MMC stack. This is a two-stage process. * First, we enable power to the card without the clock running. * We then wait a bit for the power to stabilise. Finally, * enable the bus drivers and clock to the card. * * We must _NOT_ enable the clock prior to power stablising. * * If a host does all the power sequencing itself, ignore the * initial MMC_POWER_UP stage. */ void mmc_power_up(struct mmc_host *host, u32 ocr) { if (host->ios.power_mode == MMC_POWER_ON) return; mmc_host_clk_hold(host); host->ios.vdd = fls(ocr) - 1; if (mmc_host_is_spi(host)) host->ios.chip_select = MMC_CS_HIGH; else host->ios.chip_select = MMC_CS_DONTCARE; host->ios.bus_mode = MMC_BUSMODE_PUSHPULL; host->ios.power_mode = MMC_POWER_UP; host->ios.bus_width = MMC_BUS_WIDTH_1; host->ios.timing = MMC_TIMING_LEGACY; mmc_set_ios(host); /* Set signal voltage to 3.3V */ __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330); /* * This delay should be sufficient to allow the power supply * to reach the minimum voltage. */ mmc_delay(10); host->ios.clock = host->f_init; host->ios.power_mode = MMC_POWER_ON; mmc_set_ios(host); /* * This delay must be at least 74 clock sizes, or 1 ms, or the * time required to reach a stable voltage. */ mmc_delay(10); mmc_host_clk_release(host); } void mmc_power_off(struct mmc_host *host) { if (host->ios.power_mode == MMC_POWER_OFF) return; mmc_host_clk_hold(host); host->ios.clock = 0; host->ios.vdd = 0; if (!mmc_host_is_spi(host)) { host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN; host->ios.chip_select = MMC_CS_DONTCARE; } host->ios.power_mode = MMC_POWER_OFF; host->ios.bus_width = MMC_BUS_WIDTH_1; host->ios.timing = MMC_TIMING_LEGACY; mmc_set_ios(host); /* * Some configurations, such as the 802.11 SDIO card in the OLPC * XO-1.5, require a short delay after poweroff before the card * can be successfully turned on again. */ mmc_delay(1); mmc_host_clk_release(host); } void mmc_power_cycle(struct mmc_host *host, u32 ocr) { mmc_power_off(host); /* Wait at least 1 ms according to SD spec */ mmc_delay(1); mmc_power_up(host, ocr); } /* * Cleanup when the last reference to the bus operator is dropped. */ static void __mmc_release_bus(struct mmc_host *host) { BUG_ON(!host); BUG_ON(host->bus_refs); BUG_ON(!host->bus_dead); host->bus_ops = NULL; } /* * Increase reference count of bus operator */ static inline void mmc_bus_get(struct mmc_host *host) { unsigned long flags; spin_lock_irqsave(&host->lock, flags); host->bus_refs++; spin_unlock_irqrestore(&host->lock, flags); } /* * Decrease reference count of bus operator and free it if * it is the last reference. */ static inline void mmc_bus_put(struct mmc_host *host) { unsigned long flags; spin_lock_irqsave(&host->lock, flags); host->bus_refs--; if ((host->bus_refs == 0) && host->bus_ops) __mmc_release_bus(host); spin_unlock_irqrestore(&host->lock, flags); } /* * Assign a mmc bus handler to a host. Only one bus handler may control a * host at any given time. */ void mmc_attach_bus(struct mmc_host *host, const struct mmc_bus_ops *ops) { unsigned long flags; BUG_ON(!host); BUG_ON(!ops); WARN_ON(!host->claimed); spin_lock_irqsave(&host->lock, flags); BUG_ON(host->bus_ops); BUG_ON(host->bus_refs); host->bus_ops = ops; host->bus_refs = 1; host->bus_dead = 0; spin_unlock_irqrestore(&host->lock, flags); } /* * Remove the current bus handler from a host. */ void mmc_detach_bus(struct mmc_host *host) { unsigned long flags; BUG_ON(!host); WARN_ON(!host->claimed); WARN_ON(!host->bus_ops); spin_lock_irqsave(&host->lock, flags); host->bus_dead = 1; spin_unlock_irqrestore(&host->lock, flags); mmc_bus_put(host); } static void _mmc_detect_change(struct mmc_host *host, unsigned long delay, bool cd_irq) { #ifdef CONFIG_MMC_DEBUG unsigned long flags; spin_lock_irqsave(&host->lock, flags); WARN_ON(host->removed); spin_unlock_irqrestore(&host->lock, flags); #endif /* * If the device is configured as wakeup, we prevent a new sleep for * 5 s to give provision for user space to consume the event. */ if (cd_irq && !(host->caps & MMC_CAP_NEEDS_POLL) && device_can_wakeup(mmc_dev(host))) pm_wakeup_event(mmc_dev(host), 5000); host->detect_change = 1; mmc_schedule_delayed_work(&host->detect, delay); } /** * mmc_detect_change - process change of state on a MMC socket * @host: host which changed state. * @delay: optional delay to wait before detection (jiffies) * * MMC drivers should call this when they detect a card has been * inserted or removed. The MMC layer will confirm that any * present card is still functional, and initialize any newly * inserted. */ void mmc_detect_change(struct mmc_host *host, unsigned long delay) { _mmc_detect_change(host, delay, true); } EXPORT_SYMBOL(mmc_detect_change); void mmc_init_erase(struct mmc_card *card) { unsigned int sz; if (is_power_of_2(card->erase_size)) card->erase_shift = ffs(card->erase_size) - 1; else card->erase_shift = 0; /* * It is possible to erase an arbitrarily large area of an SD or MMC * card. That is not desirable because it can take a long time * (minutes) potentially delaying more important I/O, and also the * timeout calculations become increasingly hugely over-estimated. * Consequently, 'pref_erase' is defined as a guide to limit erases * to that size and alignment. * * For SD cards that define Allocation Unit size, limit erases to one * Allocation Unit at a time. For MMC cards that define High Capacity * Erase Size, whether it is switched on or not, limit to that size. * Otherwise just have a stab at a good value. For modern cards it * will end up being 4MiB. Note that if the value is too small, it * can end up taking longer to erase. */ if (mmc_card_sd(card) && card->ssr.au) { card->pref_erase = card->ssr.au; card->erase_shift = ffs(card->ssr.au) - 1; } else if (card->ext_csd.hc_erase_size) { card->pref_erase = card->ext_csd.hc_erase_size; } else { sz = (card->csd.capacity << (card->csd.read_blkbits - 9)) >> 11; if (sz < 128) card->pref_erase = 512 * 1024 / 512; else if (sz < 512) card->pref_erase = 1024 * 1024 / 512; else if (sz < 1024) card->pref_erase = 2 * 1024 * 1024 / 512; else card->pref_erase = 4 * 1024 * 1024 / 512; if (card->pref_erase < card->erase_size) card->pref_erase = card->erase_size; else { sz = card->pref_erase % card->erase_size; if (sz) card->pref_erase += card->erase_size - sz; } } } static unsigned int mmc_mmc_erase_timeout(struct mmc_card *card, unsigned int arg, unsigned int qty) { unsigned int erase_timeout; if (arg == MMC_DISCARD_ARG || (arg == MMC_TRIM_ARG && card->ext_csd.rev >= 6)) { erase_timeout = card->ext_csd.trim_timeout; } else if (card->ext_csd.erase_group_def & 1) { /* High Capacity Erase Group Size uses HC timeouts */ if (arg == MMC_TRIM_ARG) erase_timeout = card->ext_csd.trim_timeout; else erase_timeout = card->ext_csd.hc_erase_timeout; } else { /* CSD Erase Group Size uses write timeout */ unsigned int mult = (10 << card->csd.r2w_factor); unsigned int timeout_clks = card->csd.tacc_clks * mult; unsigned int timeout_us; /* Avoid overflow: e.g. tacc_ns=80000000 mult=1280 */ if (card->csd.tacc_ns < 1000000) timeout_us = (card->csd.tacc_ns * mult) / 1000; else timeout_us = (card->csd.tacc_ns / 1000) * mult; /* * ios.clock is only a target. The real clock rate might be * less but not that much less, so fudge it by multiplying by 2. */ timeout_clks <<= 1; timeout_us += (timeout_clks * 1000) / (mmc_host_clk_rate(card->host) / 1000); erase_timeout = timeout_us / 1000; /* * Theoretically, the calculation could underflow so round up * to 1ms in that case. */ if (!erase_timeout) erase_timeout = 1; } /* Multiplier for secure operations */ if (arg & MMC_SECURE_ARGS) { if (arg == MMC_SECURE_ERASE_ARG) erase_timeout *= card->ext_csd.sec_erase_mult; else erase_timeout *= card->ext_csd.sec_trim_mult; } erase_timeout *= qty; /* * Ensure at least a 1 second timeout for SPI as per * 'mmc_set_data_timeout()' */ if (mmc_host_is_spi(card->host) && erase_timeout < 1000) erase_timeout = 1000; return erase_timeout; } static unsigned int mmc_sd_erase_timeout(struct mmc_card *card, unsigned int arg, unsigned int qty) { unsigned int erase_timeout; if (card->ssr.erase_timeout) { /* Erase timeout specified in SD Status Register (SSR) */ erase_timeout = card->ssr.erase_timeout * qty + card->ssr.erase_offset; } else { /* * Erase timeout not specified in SD Status Register (SSR) so * use 250ms per write block. */ erase_timeout = 250 * qty; } /* Must not be less than 1 second */ if (erase_timeout < 1000) erase_timeout = 1000; return erase_timeout; } static unsigned int mmc_erase_timeout(struct mmc_card *card, unsigned int arg, unsigned int qty) { if (mmc_card_sd(card)) return mmc_sd_erase_timeout(card, arg, qty); else return mmc_mmc_erase_timeout(card, arg, qty); } static int mmc_do_erase(struct mmc_card *card, unsigned int from, unsigned int to, unsigned int arg) { struct mmc_command cmd = {0}; unsigned int qty = 0; unsigned long timeout; int err; /* * qty is used to calculate the erase timeout which depends on how many * erase groups (or allocation units in SD terminology) are affected. * We count erasing part of an erase group as one erase group. * For SD, the allocation units are always a power of 2. For MMC, the * erase group size is almost certainly also power of 2, but it does not * seem to insist on that in the JEDEC standard, so we fall back to * division in that case. SD may not specify an allocation unit size, * in which case the timeout is based on the number of write blocks. * * Note that the timeout for secure trim 2 will only be correct if the * number of erase groups specified is the same as the total of all * preceding secure trim 1 commands. Since the power may have been * lost since the secure trim 1 commands occurred, it is generally * impossible to calculate the secure trim 2 timeout correctly. */ if (card->erase_shift) qty += ((to >> card->erase_shift) - (from >> card->erase_shift)) + 1; else if (mmc_card_sd(card)) qty += to - from + 1; else qty += ((to / card->erase_size) - (from / card->erase_size)) + 1; if (!mmc_card_blockaddr(card)) { from <<= 9; to <<= 9; } if (mmc_card_sd(card)) cmd.opcode = SD_ERASE_WR_BLK_START; else cmd.opcode = MMC_ERASE_GROUP_START; cmd.arg = from; cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; err = mmc_wait_for_cmd(card->host, &cmd, 0); if (err) { pr_err("mmc_erase: group start error %d, " "status %#x\n", err, cmd.resp[0]); err = -EIO; goto out; } memset(&cmd, 0, sizeof(struct mmc_command)); if (mmc_card_sd(card)) cmd.opcode = SD_ERASE_WR_BLK_END; else cmd.opcode = MMC_ERASE_GROUP_END; cmd.arg = to; cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; err = mmc_wait_for_cmd(card->host, &cmd, 0); if (err) { pr_err("mmc_erase: group end error %d, status %#x\n", err, cmd.resp[0]); err = -EIO; goto out; } memset(&cmd, 0, sizeof(struct mmc_command)); cmd.opcode = MMC_ERASE; cmd.arg = arg; cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC; cmd.busy_timeout = mmc_erase_timeout(card, arg, qty); err = mmc_wait_for_cmd(card->host, &cmd, 0); if (err) { pr_err("mmc_erase: erase error %d, status %#x\n", err, cmd.resp[0]); err = -EIO; goto out; } if (mmc_host_is_spi(card->host)) goto out; timeout = jiffies + msecs_to_jiffies(MMC_CORE_TIMEOUT_MS); do { memset(&cmd, 0, sizeof(struct mmc_command)); cmd.opcode = MMC_SEND_STATUS; cmd.arg = card->rca << 16; cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; /* Do not retry else we can't see errors */ err = mmc_wait_for_cmd(card->host, &cmd, 0); if (err || (cmd.resp[0] & 0xFDF92000)) { pr_err("error %d requesting status %#x\n", err, cmd.resp[0]); err = -EIO; goto out; } /* Timeout if the device never becomes ready for data and * never leaves the program state. */ if (time_after(jiffies, timeout)) { pr_err("%s: Card stuck in programming state! %s\n", mmc_hostname(card->host), __func__); err = -EIO; goto out; } } while (!(cmd.resp[0] & R1_READY_FOR_DATA) || (R1_CURRENT_STATE(cmd.resp[0]) == R1_STATE_PRG)); out: return err; } /** * mmc_erase - erase sectors. * @card: card to erase * @from: first sector to erase * @nr: number of sectors to erase * @arg: erase command argument (SD supports only %MMC_ERASE_ARG) * * Caller must claim host before calling this function. */ int mmc_erase(struct mmc_card *card, unsigned int from, unsigned int nr, unsigned int arg) { unsigned int rem, to = from + nr; if (!(card->host->caps & MMC_CAP_ERASE) || !(card->csd.cmdclass & CCC_ERASE)) return -EOPNOTSUPP; if (!card->erase_size) return -EOPNOTSUPP; if (mmc_card_sd(card) && arg != MMC_ERASE_ARG) return -EOPNOTSUPP; if ((arg & MMC_SECURE_ARGS) && !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN)) return -EOPNOTSUPP; if ((arg & MMC_TRIM_ARGS) && !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN)) return -EOPNOTSUPP; if (arg == MMC_SECURE_ERASE_ARG) { if (from % card->erase_size || nr % card->erase_size) return -EINVAL; } if (arg == MMC_ERASE_ARG) { rem = from % card->erase_size; if (rem) { rem = card->erase_size - rem; from += rem; if (nr > rem) nr -= rem; else return 0; } rem = nr % card->erase_size; if (rem) nr -= rem; } if (nr == 0) return 0; to = from + nr; if (to <= from) return -EINVAL; /* 'from' and 'to' are inclusive */ to -= 1; return mmc_do_erase(card, from, to, arg); } EXPORT_SYMBOL(mmc_erase); int mmc_can_erase(struct mmc_card *card) { if ((card->host->caps & MMC_CAP_ERASE) && (card->csd.cmdclass & CCC_ERASE) && card->erase_size) return 1; return 0; } EXPORT_SYMBOL(mmc_can_erase); int mmc_can_trim(struct mmc_card *card) { if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN) return 1; return 0; } EXPORT_SYMBOL(mmc_can_trim); int mmc_can_discard(struct mmc_card *card) { /* * As there's no way to detect the discard support bit at v4.5 * use the s/w feature support filed. */ if (card->ext_csd.feature_support & MMC_DISCARD_FEATURE) return 1; return 0; } EXPORT_SYMBOL(mmc_can_discard); int mmc_can_sanitize(struct mmc_card *card) { if (!mmc_can_trim(card) && !mmc_can_erase(card)) return 0; if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_SANITIZE) return 1; return 0; } EXPORT_SYMBOL(mmc_can_sanitize); int mmc_can_secure_erase_trim(struct mmc_card *card) { if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN) return 1; return 0; } EXPORT_SYMBOL(mmc_can_secure_erase_trim); int mmc_erase_group_aligned(struct mmc_card *card, unsigned int from, unsigned int nr) { if (!card->erase_size) return 0; if (from % card->erase_size || nr % card->erase_size) return 0; return 1; } EXPORT_SYMBOL(mmc_erase_group_aligned); static unsigned int mmc_do_calc_max_discard(struct mmc_card *card, unsigned int arg) { struct mmc_host *host = card->host; unsigned int max_discard, x, y, qty = 0, max_qty, timeout; unsigned int last_timeout = 0; if (card->erase_shift) max_qty = UINT_MAX >> card->erase_shift; else if (mmc_card_sd(card)) max_qty = UINT_MAX; else max_qty = UINT_MAX / card->erase_size; /* Find the largest qty with an OK timeout */ do { y = 0; for (x = 1; x && x <= max_qty && max_qty - x >= qty; x <<= 1) { timeout = mmc_erase_timeout(card, arg, qty + x); if (timeout > host->max_busy_timeout) break; if (timeout < last_timeout) break; last_timeout = timeout; y = x; } qty += y; } while (y); if (!qty) return 0; if (qty == 1) return 1; /* Convert qty to sectors */ if (card->erase_shift) max_discard = --qty << card->erase_shift; else if (mmc_card_sd(card)) max_discard = qty; else max_discard = --qty * card->erase_size; return max_discard; } unsigned int mmc_calc_max_discard(struct mmc_card *card) { struct mmc_host *host = card->host; unsigned int max_discard, max_trim; if (!host->max_busy_timeout) return UINT_MAX; /* * Without erase_group_def set, MMC erase timeout depends on clock * frequence which can change. In that case, the best choice is * just the preferred erase size. */ if (mmc_card_mmc(card) && !(card->ext_csd.erase_group_def & 1)) return card->pref_erase; max_discard = mmc_do_calc_max_discard(card, MMC_ERASE_ARG); if (mmc_can_trim(card)) { max_trim = mmc_do_calc_max_discard(card, MMC_TRIM_ARG); if (max_trim < max_discard) max_discard = max_trim; } else if (max_discard < card->erase_size) { max_discard = 0; } pr_debug("%s: calculated max. discard sectors %u for timeout %u ms\n", mmc_hostname(host), max_discard, host->max_busy_timeout); return max_discard; } EXPORT_SYMBOL(mmc_calc_max_discard); int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen) { struct mmc_command cmd = {0}; if (mmc_card_blockaddr(card) || mmc_card_ddr_mode(card)) return 0; cmd.opcode = MMC_SET_BLOCKLEN; cmd.arg = blocklen; cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; return mmc_wait_for_cmd(card->host, &cmd, 5); } EXPORT_SYMBOL(mmc_set_blocklen); int mmc_set_blockcount(struct mmc_card *card, unsigned int blockcount, bool is_rel_write) { struct mmc_command cmd = {0}; cmd.opcode = MMC_SET_BLOCK_COUNT; cmd.arg = blockcount & 0x0000FFFF; if (is_rel_write) cmd.arg |= 1 << 31; cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; return mmc_wait_for_cmd(card->host, &cmd, 5); } EXPORT_SYMBOL(mmc_set_blockcount); static void mmc_hw_reset_for_init(struct mmc_host *host) { if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset) return; mmc_host_clk_hold(host); host->ops->hw_reset(host); mmc_host_clk_release(host); } int mmc_can_reset(struct mmc_card *card) { u8 rst_n_function; if (!mmc_card_mmc(card)) return 0; rst_n_function = card->ext_csd.rst_n_function; if ((rst_n_function & EXT_CSD_RST_N_EN_MASK) != EXT_CSD_RST_N_ENABLED) return 0; return 1; } EXPORT_SYMBOL(mmc_can_reset); static int mmc_do_hw_reset(struct mmc_host *host, int check) { struct mmc_card *card = host->card; if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset) return -EOPNOTSUPP; if (!card) return -EINVAL; if (!mmc_can_reset(card)) return -EOPNOTSUPP; mmc_host_clk_hold(host); mmc_set_clock(host, host->f_init); host->ops->hw_reset(host); /* If the reset has happened, then a status command will fail */ if (check) { struct mmc_command cmd = {0}; int err; cmd.opcode = MMC_SEND_STATUS; if (!mmc_host_is_spi(card->host)) cmd.arg = card->rca << 16; cmd.flags = MMC_RSP_SPI_R2 | MMC_RSP_R1 | MMC_CMD_AC; err = mmc_wait_for_cmd(card->host, &cmd, 0); if (!err) { mmc_host_clk_release(host); return -ENOSYS; } } host->card->state &= ~(MMC_STATE_HIGHSPEED | MMC_STATE_HIGHSPEED_DDR); if (mmc_host_is_spi(host)) { host->ios.chip_select = MMC_CS_HIGH; host->ios.bus_mode = MMC_BUSMODE_PUSHPULL; } else { host->ios.chip_select = MMC_CS_DONTCARE; host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN; } host->ios.bus_width = MMC_BUS_WIDTH_1; host->ios.timing = MMC_TIMING_LEGACY; mmc_set_ios(host); mmc_host_clk_release(host); return host->bus_ops->power_restore(host); } int mmc_hw_reset(struct mmc_host *host) { return mmc_do_hw_reset(host, 0); } EXPORT_SYMBOL(mmc_hw_reset); int mmc_hw_reset_check(struct mmc_host *host) { return mmc_do_hw_reset(host, 1); } EXPORT_SYMBOL(mmc_hw_reset_check); static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq) { host->f_init = freq; #ifdef CONFIG_MMC_DEBUG pr_info("%s: %s: trying to init card at %u Hz\n", mmc_hostname(host), __func__, host->f_init); #endif mmc_power_up(host, host->ocr_avail); /* * Some eMMCs (with VCCQ always on) may not be reset after power up, so * do a hardware reset if possible. */ mmc_hw_reset_for_init(host); /* * sdio_reset sends CMD52 to reset card. Since we do not know * if the card is being re-initialized, just send it. CMD52 * should be ignored by SD/eMMC cards. */ sdio_reset(host); mmc_go_idle(host); mmc_send_if_cond(host, host->ocr_avail); /* Order's important: probe SDIO, then SD, then MMC */ if (!mmc_attach_sdio(host)) return 0; if (!mmc_attach_sd(host)) return 0; if (!mmc_attach_mmc(host)) return 0; mmc_power_off(host); return -EIO; } int _mmc_detect_card_removed(struct mmc_host *host) { int ret; if (host->caps & MMC_CAP_NONREMOVABLE) return 0; if (!host->card || mmc_card_removed(host->card)) return 1; ret = host->bus_ops->alive(host); /* * Card detect status and alive check may be out of sync if card is * removed slowly, when card detect switch changes while card/slot * pads are still contacted in hardware (refer to "SD Card Mechanical * Addendum, Appendix C: Card Detection Switch"). So reschedule a * detect work 200ms later for this case. */ if (!ret && host->ops->get_cd && !host->ops->get_cd(host)) { mmc_detect_change(host, msecs_to_jiffies(200)); pr_debug("%s: card removed too slowly\n", mmc_hostname(host)); } if (ret) { mmc_card_set_removed(host->card); pr_debug("%s: card remove detected\n", mmc_hostname(host)); } return ret; } int mmc_detect_card_removed(struct mmc_host *host) { struct mmc_card *card = host->card; int ret; WARN_ON(!host->claimed); if (!card) return 1; ret = mmc_card_removed(card); /* * The card will be considered unchanged unless we have been asked to * detect a change or host requires polling to provide card detection. */ if (!host->detect_change && !(host->caps & MMC_CAP_NEEDS_POLL)) return ret; host->detect_change = 0; if (!ret) { ret = _mmc_detect_card_removed(host); if (ret && (host->caps & MMC_CAP_NEEDS_POLL)) { /* * Schedule a detect work as soon as possible to let a * rescan handle the card removal. */ cancel_delayed_work(&host->detect); _mmc_detect_change(host, 0, false); } } return ret; } EXPORT_SYMBOL(mmc_detect_card_removed); void mmc_rescan(struct work_struct *work) { struct mmc_host *host = container_of(work, struct mmc_host, detect.work); int i; if (host->rescan_disable) return; /* If there is a non-removable card registered, only scan once */ if ((host->caps & MMC_CAP_NONREMOVABLE) && host->rescan_entered) return; host->rescan_entered = 1; mmc_bus_get(host); /* * if there is a _removable_ card registered, check whether it is * still present */ if (host->bus_ops && !host->bus_dead && !(host->caps & MMC_CAP_NONREMOVABLE)) host->bus_ops->detect(host); host->detect_change = 0; /* * Let mmc_bus_put() free the bus/bus_ops if we've found that * the card is no longer present. */ mmc_bus_put(host); mmc_bus_get(host); /* if there still is a card present, stop here */ if (host->bus_ops != NULL) { mmc_bus_put(host); goto out; } /* * Only we can add a new handler, so it's safe to * release the lock here. */ mmc_bus_put(host); if (!(host->caps & MMC_CAP_NONREMOVABLE) && host->ops->get_cd && host->ops->get_cd(host) == 0) { mmc_claim_host(host); mmc_power_off(host); mmc_release_host(host); goto out; } mmc_claim_host(host); for (i = 0; i < ARRAY_SIZE(freqs); i++) { if (!mmc_rescan_try_freq(host, max(freqs[i], host->f_min))) break; if (freqs[i] <= host->f_min) break; } mmc_release_host(host); out: if (host->caps & MMC_CAP_NEEDS_POLL) mmc_schedule_delayed_work(&host->detect, HZ); } void mmc_start_host(struct mmc_host *host) { host->f_init = max(freqs[0], host->f_min); host->rescan_disable = 0; if (host->caps2 & MMC_CAP2_NO_PRESCAN_POWERUP) mmc_power_off(host); else mmc_power_up(host, host->ocr_avail); _mmc_detect_change(host, 0, false); } void mmc_stop_host(struct mmc_host *host) { #ifdef CONFIG_MMC_DEBUG unsigned long flags; spin_lock_irqsave(&host->lock, flags); host->removed = 1; spin_unlock_irqrestore(&host->lock, flags); #endif host->rescan_disable = 1; cancel_delayed_work_sync(&host->detect); mmc_flush_scheduled_work(); /* clear pm flags now and let card drivers set them as needed */ host->pm_flags = 0; mmc_bus_get(host); if (host->bus_ops && !host->bus_dead) { /* Calling bus_ops->remove() with a claimed host can deadlock */ host->bus_ops->remove(host); mmc_claim_host(host); mmc_detach_bus(host); mmc_power_off(host); mmc_release_host(host); mmc_bus_put(host); return; } mmc_bus_put(host); BUG_ON(host->card); mmc_power_off(host); } int mmc_power_save_host(struct mmc_host *host) { int ret = 0; #ifdef CONFIG_MMC_DEBUG pr_info("%s: %s: powering down\n", mmc_hostname(host), __func__); #endif mmc_bus_get(host); if (!host->bus_ops || host->bus_dead) { mmc_bus_put(host); return -EINVAL; } if (host->bus_ops->power_save) ret = host->bus_ops->power_save(host); mmc_bus_put(host); mmc_power_off(host); return ret; } EXPORT_SYMBOL(mmc_power_save_host); int mmc_power_restore_host(struct mmc_host *host) { int ret; #ifdef CONFIG_MMC_DEBUG pr_info("%s: %s: powering up\n", mmc_hostname(host), __func__); #endif mmc_bus_get(host); if (!host->bus_ops || host->bus_dead) { mmc_bus_put(host); return -EINVAL; } mmc_power_up(host, host->card->ocr); ret = host->bus_ops->power_restore(host); mmc_bus_put(host); return ret; } EXPORT_SYMBOL(mmc_power_restore_host); /* * Flush the cache to the non-volatile storage. */ int mmc_flush_cache(struct mmc_card *card) { int err = 0; if (mmc_card_mmc(card) && (card->ext_csd.cache_size > 0) && (card->ext_csd.cache_ctrl & 1)) { err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_FLUSH_CACHE, 1, 0); if (err) pr_err("%s: cache flush error %d\n", mmc_hostname(card->host), err); } return err; } EXPORT_SYMBOL(mmc_flush_cache); #ifdef CONFIG_PM /* Do the card removal on suspend if card is assumed removeable * Do that in pm notifier while userspace isn't yet frozen, so we will be able to sync the card. */ int mmc_pm_notify(struct notifier_block *notify_block, unsigned long mode, void *unused) { struct mmc_host *host = container_of( notify_block, struct mmc_host, pm_notify); unsigned long flags; int err = 0; switch (mode) { case PM_HIBERNATION_PREPARE: case PM_SUSPEND_PREPARE: spin_lock_irqsave(&host->lock, flags); host->rescan_disable = 1; spin_unlock_irqrestore(&host->lock, flags); cancel_delayed_work_sync(&host->detect); if (!host->bus_ops) break; /* Validate prerequisites for suspend */ if (host->bus_ops->pre_suspend) err = host->bus_ops->pre_suspend(host); if (!err) break; /* Calling bus_ops->remove() with a claimed host can deadlock */ host->bus_ops->remove(host); mmc_claim_host(host); mmc_detach_bus(host); mmc_power_off(host); mmc_release_host(host); host->pm_flags = 0; break; case PM_POST_SUSPEND: case PM_POST_HIBERNATION: case PM_POST_RESTORE: spin_lock_irqsave(&host->lock, flags); host->rescan_disable = 0; spin_unlock_irqrestore(&host->lock, flags); _mmc_detect_change(host, 0, false); } return 0; } #endif /** * mmc_init_context_info() - init synchronization context * @host: mmc host * * Init struct context_info needed to implement asynchronous * request mechanism, used by mmc core, host driver and mmc requests * supplier. */ void mmc_init_context_info(struct mmc_host *host) { spin_lock_init(&host->context_info.lock); host->context_info.is_new_req = false; host->context_info.is_done_rcv = false; host->context_info.is_waiting_last_req = false; init_waitqueue_head(&host->context_info.wait); } static int __init mmc_init(void) { int ret; workqueue = alloc_ordered_workqueue("kmmcd", 0); if (!workqueue) return -ENOMEM; ret = mmc_register_bus(); if (ret) goto destroy_workqueue; ret = mmc_register_host_class(); if (ret) goto unregister_bus; ret = sdio_register_bus(); if (ret) goto unregister_host_class; return 0; unregister_host_class: mmc_unregister_host_class(); unregister_bus: mmc_unregister_bus(); destroy_workqueue: destroy_workqueue(workqueue); return ret; } static void __exit mmc_exit(void) { sdio_unregister_bus(); mmc_unregister_host_class(); mmc_unregister_bus(); destroy_workqueue(workqueue); } subsys_initcall(mmc_init); module_exit(mmc_exit); MODULE_LICENSE("GPL");