/* * Copyright (c) 2010 Broadcom Corporation * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above * copyright notice and this permission notice appear in all copies. * * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */ #ifndef _BRCM_D11_H_ #define _BRCM_D11_H_ #include #include #include "pub.h" #include "dma.h" /* RX FIFO numbers */ #define RX_FIFO 0 /* data and ctl frames */ #define RX_TXSTATUS_FIFO 3 /* RX fifo for tx status packages */ /* TX FIFO numbers using WME Access Category */ #define TX_AC_BK_FIFO 0 /* Background TX FIFO */ #define TX_AC_BE_FIFO 1 /* Best-Effort TX FIFO */ #define TX_AC_VI_FIFO 2 /* Video TX FIFO */ #define TX_AC_VO_FIFO 3 /* Voice TX FIFO */ #define TX_BCMC_FIFO 4 /* Broadcast/Multicast TX FIFO */ #define TX_ATIM_FIFO 5 /* TX fifo for ATIM window info */ /* Addr is byte address used by SW; offset is word offset used by uCode */ /* Per AC TX limit settings */ #define M_AC_TXLMT_BASE_ADDR (0x180 * 2) #define M_AC_TXLMT_ADDR(_ac) (M_AC_TXLMT_BASE_ADDR + (2 * (_ac))) /* Legacy TX FIFO numbers */ #define TX_DATA_FIFO TX_AC_BE_FIFO #define TX_CTL_FIFO TX_AC_VO_FIFO #define WL_RSSI_ANT_MAX 4 /* max possible rx antennas */ struct intctrlregs { u32 intstatus; u32 intmask; }; /* PIO structure, * support two PIO format: 2 bytes access and 4 bytes access * basic FIFO register set is per channel(transmit or receive) * a pair of channels is defined for convenience */ /* 2byte-wide pio register set per channel(xmt or rcv) */ struct pio2regs { u16 fifocontrol; u16 fifodata; u16 fifofree; /* only valid in xmt channel, not in rcv channel */ u16 PAD; }; /* a pair of pio channels(tx and rx) */ struct pio2regp { struct pio2regs tx; struct pio2regs rx; }; /* 4byte-wide pio register set per channel(xmt or rcv) */ struct pio4regs { u32 fifocontrol; u32 fifodata; }; /* a pair of pio channels(tx and rx) */ struct pio4regp { struct pio4regs tx; struct pio4regs rx; }; /* read: 32-bit register that can be read as 32-bit or as 2 16-bit * write: only low 16b-it half can be written */ union pmqreg { u32 pmqhostdata; /* read only! */ struct { u16 pmqctrlstatus; /* read/write */ u16 PAD; } w; }; struct fifo64 { struct dma64regs dmaxmt; /* dma tx */ struct pio4regs piotx; /* pio tx */ struct dma64regs dmarcv; /* dma rx */ struct pio4regs piorx; /* pio rx */ }; /* * Host Interface Registers */ struct d11regs { /* Device Control ("semi-standard host registers") */ u32 PAD[3]; /* 0x0 - 0x8 */ u32 biststatus; /* 0xC */ u32 biststatus2; /* 0x10 */ u32 PAD; /* 0x14 */ u32 gptimer; /* 0x18 */ u32 usectimer; /* 0x1c *//* for corerev >= 26 */ /* Interrupt Control *//* 0x20 */ struct intctrlregs intctrlregs[8]; u32 PAD[40]; /* 0x60 - 0xFC */ u32 intrcvlazy[4]; /* 0x100 - 0x10C */ u32 PAD[4]; /* 0x110 - 0x11c */ u32 maccontrol; /* 0x120 */ u32 maccommand; /* 0x124 */ u32 macintstatus; /* 0x128 */ u32 macintmask; /* 0x12C */ /* Transmit Template Access */ u32 tplatewrptr; /* 0x130 */ u32 tplatewrdata; /* 0x134 */ u32 PAD[2]; /* 0x138 - 0x13C */ /* PMQ registers */ union pmqreg pmqreg; /* 0x140 */ u32 pmqpatl; /* 0x144 */ u32 pmqpath; /* 0x148 */ u32 PAD; /* 0x14C */ u32 chnstatus; /* 0x150 */ u32 psmdebug; /* 0x154 */ u32 phydebug; /* 0x158 */ u32 machwcap; /* 0x15C */ /* Extended Internal Objects */ u32 objaddr; /* 0x160 */ u32 objdata; /* 0x164 */ u32 PAD[2]; /* 0x168 - 0x16c */ u32 frmtxstatus; /* 0x170 */ u32 frmtxstatus2; /* 0x174 */ u32 PAD[2]; /* 0x178 - 0x17c */ /* TSF host access */ u32 tsf_timerlow; /* 0x180 */ u32 tsf_timerhigh; /* 0x184 */ u32 tsf_cfprep; /* 0x188 */ u32 tsf_cfpstart; /* 0x18c */ u32 tsf_cfpmaxdur32; /* 0x190 */ u32 PAD[3]; /* 0x194 - 0x19c */ u32 maccontrol1; /* 0x1a0 */ u32 machwcap1; /* 0x1a4 */ u32 PAD[14]; /* 0x1a8 - 0x1dc */ /* Clock control and hardware workarounds*/ u32 clk_ctl_st; /* 0x1e0 */ u32 hw_war; u32 d11_phypllctl; /* the phypll request/avail bits are * moved to clk_ctl_st */ u32 PAD[5]; /* 0x1ec - 0x1fc */ /* 0x200-0x37F dma/pio registers */ struct fifo64 fifo64regs[6]; /* FIFO diagnostic port access */ struct dma32diag dmafifo; /* 0x380 - 0x38C */ u32 aggfifocnt; /* 0x390 */ u32 aggfifodata; /* 0x394 */ u32 PAD[16]; /* 0x398 - 0x3d4 */ u16 radioregaddr; /* 0x3d8 */ u16 radioregdata; /* 0x3da */ /* * time delay between the change on rf disable input and * radio shutdown */ u32 rfdisabledly; /* 0x3DC */ /* PHY register access */ u16 phyversion; /* 0x3e0 - 0x0 */ u16 phybbconfig; /* 0x3e2 - 0x1 */ u16 phyadcbias; /* 0x3e4 - 0x2 Bphy only */ u16 phyanacore; /* 0x3e6 - 0x3 pwwrdwn on aphy */ u16 phyrxstatus0; /* 0x3e8 - 0x4 */ u16 phyrxstatus1; /* 0x3ea - 0x5 */ u16 phycrsth; /* 0x3ec - 0x6 */ u16 phytxerror; /* 0x3ee - 0x7 */ u16 phychannel; /* 0x3f0 - 0x8 */ u16 PAD[1]; /* 0x3f2 - 0x9 */ u16 phytest; /* 0x3f4 - 0xa */ u16 phy4waddr; /* 0x3f6 - 0xb */ u16 phy4wdatahi; /* 0x3f8 - 0xc */ u16 phy4wdatalo; /* 0x3fa - 0xd */ u16 phyregaddr; /* 0x3fc - 0xe */ u16 phyregdata; /* 0x3fe - 0xf */ /* IHR *//* 0x400 - 0x7FE */ /* RXE Block */ u16 PAD[3]; /* 0x400 - 0x406 */ u16 rcv_fifo_ctl; /* 0x406 */ u16 PAD; /* 0x408 - 0x40a */ u16 rcv_frm_cnt; /* 0x40a */ u16 PAD[4]; /* 0x40a - 0x414 */ u16 rssi; /* 0x414 */ u16 PAD[5]; /* 0x414 - 0x420 */ u16 rcm_ctl; /* 0x420 */ u16 rcm_mat_data; /* 0x422 */ u16 rcm_mat_mask; /* 0x424 */ u16 rcm_mat_dly; /* 0x426 */ u16 rcm_cond_mask_l; /* 0x428 */ u16 rcm_cond_mask_h; /* 0x42A */ u16 rcm_cond_dly; /* 0x42C */ u16 PAD[1]; /* 0x42E */ u16 ext_ihr_addr; /* 0x430 */ u16 ext_ihr_data; /* 0x432 */ u16 rxe_phyrs_2; /* 0x434 */ u16 rxe_phyrs_3; /* 0x436 */ u16 phy_mode; /* 0x438 */ u16 rcmta_ctl; /* 0x43a */ u16 rcmta_size; /* 0x43c */ u16 rcmta_addr0; /* 0x43e */ u16 rcmta_addr1; /* 0x440 */ u16 rcmta_addr2; /* 0x442 */ u16 PAD[30]; /* 0x444 - 0x480 */ /* PSM Block *//* 0x480 - 0x500 */ u16 PAD; /* 0x480 */ u16 psm_maccontrol_h; /* 0x482 */ u16 psm_macintstatus_l; /* 0x484 */ u16 psm_macintstatus_h; /* 0x486 */ u16 psm_macintmask_l; /* 0x488 */ u16 psm_macintmask_h; /* 0x48A */ u16 PAD; /* 0x48C */ u16 psm_maccommand; /* 0x48E */ u16 psm_brc; /* 0x490 */ u16 psm_phy_hdr_param; /* 0x492 */ u16 psm_postcard; /* 0x494 */ u16 psm_pcard_loc_l; /* 0x496 */ u16 psm_pcard_loc_h; /* 0x498 */ u16 psm_gpio_in; /* 0x49A */ u16 psm_gpio_out; /* 0x49C */ u16 psm_gpio_oe; /* 0x49E */ u16 psm_bred_0; /* 0x4A0 */ u16 psm_bred_1; /* 0x4A2 */ u16 psm_bred_2; /* 0x4A4 */ u16 psm_bred_3; /* 0x4A6 */ u16 psm_brcl_0; /* 0x4A8 */ u16 psm_brcl_1; /* 0x4AA */ u16 psm_brcl_2; /* 0x4AC */ u16 psm_brcl_3; /* 0x4AE */ u16 psm_brpo_0; /* 0x4B0 */ u16 psm_brpo_1; /* 0x4B2 */ u16 psm_brpo_2; /* 0x4B4 */ u16 psm_brpo_3; /* 0x4B6 */ u16 psm_brwk_0; /* 0x4B8 */ u16 psm_brwk_1; /* 0x4BA */ u16 psm_brwk_2; /* 0x4BC */ u16 psm_brwk_3; /* 0x4BE */ u16 psm_base_0; /* 0x4C0 */ u16 psm_base_1; /* 0x4C2 */ u16 psm_base_2; /* 0x4C4 */ u16 psm_base_3; /* 0x4C6 */ u16 psm_base_4; /* 0x4C8 */ u16 psm_base_5; /* 0x4CA */ u16 psm_base_6; /* 0x4CC */ u16 psm_pc_reg_0; /* 0x4CE */ u16 psm_pc_reg_1; /* 0x4D0 */ u16 psm_pc_reg_2; /* 0x4D2 */ u16 psm_pc_reg_3; /* 0x4D4 */ u16 PAD[0xD]; /* 0x4D6 - 0x4DE */ u16 psm_corectlsts; /* 0x4f0 *//* Corerev >= 13 */ u16 PAD[0x7]; /* 0x4f2 - 0x4fE */ /* TXE0 Block *//* 0x500 - 0x580 */ u16 txe_ctl; /* 0x500 */ u16 txe_aux; /* 0x502 */ u16 txe_ts_loc; /* 0x504 */ u16 txe_time_out; /* 0x506 */ u16 txe_wm_0; /* 0x508 */ u16 txe_wm_1; /* 0x50A */ u16 txe_phyctl; /* 0x50C */ u16 txe_status; /* 0x50E */ u16 txe_mmplcp0; /* 0x510 */ u16 txe_mmplcp1; /* 0x512 */ u16 txe_phyctl1; /* 0x514 */ u16 PAD[0x05]; /* 0x510 - 0x51E */ /* Transmit control */ u16 xmtfifodef; /* 0x520 */ u16 xmtfifo_frame_cnt; /* 0x522 *//* Corerev >= 16 */ u16 xmtfifo_byte_cnt; /* 0x524 *//* Corerev >= 16 */ u16 xmtfifo_head; /* 0x526 *//* Corerev >= 16 */ u16 xmtfifo_rd_ptr; /* 0x528 *//* Corerev >= 16 */ u16 xmtfifo_wr_ptr; /* 0x52A *//* Corerev >= 16 */ u16 xmtfifodef1; /* 0x52C *//* Corerev >= 16 */ u16 PAD[0x09]; /* 0x52E - 0x53E */ u16 xmtfifocmd; /* 0x540 */ u16 xmtfifoflush; /* 0x542 */ u16 xmtfifothresh; /* 0x544 */ u16 xmtfifordy; /* 0x546 */ u16 xmtfifoprirdy; /* 0x548 */ u16 xmtfiforqpri; /* 0x54A */ u16 xmttplatetxptr; /* 0x54C */ u16 PAD; /* 0x54E */ u16 xmttplateptr; /* 0x550 */ u16 smpl_clct_strptr; /* 0x552 *//* Corerev >= 22 */ u16 smpl_clct_stpptr; /* 0x554 *//* Corerev >= 22 */ u16 smpl_clct_curptr; /* 0x556 *//* Corerev >= 22 */ u16 PAD[0x04]; /* 0x558 - 0x55E */ u16 xmttplatedatalo; /* 0x560 */ u16 xmttplatedatahi; /* 0x562 */ u16 PAD[2]; /* 0x564 - 0x566 */ u16 xmtsel; /* 0x568 */ u16 xmttxcnt; /* 0x56A */ u16 xmttxshmaddr; /* 0x56C */ u16 PAD[0x09]; /* 0x56E - 0x57E */ /* TXE1 Block */ u16 PAD[0x40]; /* 0x580 - 0x5FE */ /* TSF Block */ u16 PAD[0X02]; /* 0x600 - 0x602 */ u16 tsf_cfpstrt_l; /* 0x604 */ u16 tsf_cfpstrt_h; /* 0x606 */ u16 PAD[0X05]; /* 0x608 - 0x610 */ u16 tsf_cfppretbtt; /* 0x612 */ u16 PAD[0XD]; /* 0x614 - 0x62C */ u16 tsf_clk_frac_l; /* 0x62E */ u16 tsf_clk_frac_h; /* 0x630 */ u16 PAD[0X14]; /* 0x632 - 0x658 */ u16 tsf_random; /* 0x65A */ u16 PAD[0x05]; /* 0x65C - 0x664 */ /* GPTimer 2 registers */ u16 tsf_gpt2_stat; /* 0x666 */ u16 tsf_gpt2_ctr_l; /* 0x668 */ u16 tsf_gpt2_ctr_h; /* 0x66A */ u16 tsf_gpt2_val_l; /* 0x66C */ u16 tsf_gpt2_val_h; /* 0x66E */ u16 tsf_gptall_stat; /* 0x670 */ u16 PAD[0x07]; /* 0x672 - 0x67E */ /* IFS Block */ u16 ifs_sifs_rx_tx_tx; /* 0x680 */ u16 ifs_sifs_nav_tx; /* 0x682 */ u16 ifs_slot; /* 0x684 */ u16 PAD; /* 0x686 */ u16 ifs_ctl; /* 0x688 */ u16 PAD[0x3]; /* 0x68a - 0x68F */ u16 ifsstat; /* 0x690 */ u16 ifsmedbusyctl; /* 0x692 */ u16 iftxdur; /* 0x694 */ u16 PAD[0x3]; /* 0x696 - 0x69b */ /* EDCF support in dot11macs */ u16 ifs_aifsn; /* 0x69c */ u16 ifs_ctl1; /* 0x69e */ /* slow clock registers */ u16 scc_ctl; /* 0x6a0 */ u16 scc_timer_l; /* 0x6a2 */ u16 scc_timer_h; /* 0x6a4 */ u16 scc_frac; /* 0x6a6 */ u16 scc_fastpwrup_dly; /* 0x6a8 */ u16 scc_per; /* 0x6aa */ u16 scc_per_frac; /* 0x6ac */ u16 scc_cal_timer_l; /* 0x6ae */ u16 scc_cal_timer_h; /* 0x6b0 */ u16 PAD; /* 0x6b2 */ u16 PAD[0x26]; /* NAV Block */ u16 nav_ctl; /* 0x700 */ u16 navstat; /* 0x702 */ u16 PAD[0x3e]; /* 0x702 - 0x77E */ /* WEP/PMQ Block *//* 0x780 - 0x7FE */ u16 PAD[0x20]; /* 0x780 - 0x7BE */ u16 wepctl; /* 0x7C0 */ u16 wepivloc; /* 0x7C2 */ u16 wepivkey; /* 0x7C4 */ u16 wepwkey; /* 0x7C6 */ u16 PAD[4]; /* 0x7C8 - 0x7CE */ u16 pcmctl; /* 0X7D0 */ u16 pcmstat; /* 0X7D2 */ u16 PAD[6]; /* 0x7D4 - 0x7DE */ u16 pmqctl; /* 0x7E0 */ u16 pmqstatus; /* 0x7E2 */ u16 pmqpat0; /* 0x7E4 */ u16 pmqpat1; /* 0x7E6 */ u16 pmqpat2; /* 0x7E8 */ u16 pmqdat; /* 0x7EA */ u16 pmqdator; /* 0x7EC */ u16 pmqhst; /* 0x7EE */ u16 pmqpath0; /* 0x7F0 */ u16 pmqpath1; /* 0x7F2 */ u16 pmqpath2; /* 0x7F4 */ u16 pmqdath; /* 0x7F6 */ u16 PAD[0x04]; /* 0x7F8 - 0x7FE */ /* SHM *//* 0x800 - 0xEFE */ u16 PAD[0x380]; /* 0x800 - 0xEFE */ }; /* d11 register field offset */ #define D11REGOFFS(field) offsetof(struct d11regs, field) #define PIHR_BASE 0x0400 /* byte address of packed IHR region */ /* biststatus */ #define BT_DONE (1U << 31) /* bist done */ #define BT_B2S (1 << 30) /* bist2 ram summary bit */ /* intstatus and intmask */ #define I_PC (1 << 10) /* pci descriptor error */ #define I_PD (1 << 11) /* pci data error */ #define I_DE (1 << 12) /* descriptor protocol error */ #define I_RU (1 << 13) /* receive descriptor underflow */ #define I_RO (1 << 14) /* receive fifo overflow */ #define I_XU (1 << 15) /* transmit fifo underflow */ #define I_RI (1 << 16) /* receive interrupt */ #define I_XI (1 << 24) /* transmit interrupt */ /* interrupt receive lazy */ #define IRL_TO_MASK 0x00ffffff /* timeout */ #define IRL_FC_MASK 0xff000000 /* frame count */ #define IRL_FC_SHIFT 24 /* frame count */ /*== maccontrol register ==*/ #define MCTL_GMODE (1U << 31) #define MCTL_DISCARD_PMQ (1 << 30) #define MCTL_WAKE (1 << 26) #define MCTL_HPS (1 << 25) #define MCTL_PROMISC (1 << 24) #define MCTL_KEEPBADFCS (1 << 23) #define MCTL_KEEPCONTROL (1 << 22) #define MCTL_PHYLOCK (1 << 21) #define MCTL_BCNS_PROMISC (1 << 20) #define MCTL_LOCK_RADIO (1 << 19) #define MCTL_AP (1 << 18) #define MCTL_INFRA (1 << 17) #define MCTL_BIGEND (1 << 16) #define MCTL_GPOUT_SEL_MASK (3 << 14) #define MCTL_GPOUT_SEL_SHIFT 14 #define MCTL_EN_PSMDBG (1 << 13) #define MCTL_IHR_EN (1 << 10) #define MCTL_SHM_UPPER (1 << 9) #define MCTL_SHM_EN (1 << 8) #define MCTL_PSM_JMP_0 (1 << 2) #define MCTL_PSM_RUN (1 << 1) #define MCTL_EN_MAC (1 << 0) /*== maccommand register ==*/ #define MCMD_BCN0VLD (1 << 0) #define MCMD_BCN1VLD (1 << 1) #define MCMD_DIRFRMQVAL (1 << 2) #define MCMD_CCA (1 << 3) #define MCMD_BG_NOISE (1 << 4) #define MCMD_SKIP_SHMINIT (1 << 5) /* only used for simulation */ #define MCMD_SAMPLECOLL MCMD_SKIP_SHMINIT /* reuse for sample collect */ /*== macintstatus/macintmask ==*/ /* gracefully suspended */ #define MI_MACSSPNDD (1 << 0) /* beacon template available */ #define MI_BCNTPL (1 << 1) /* TBTT indication */ #define MI_TBTT (1 << 2) /* beacon successfully tx'd */ #define MI_BCNSUCCESS (1 << 3) /* beacon canceled (IBSS) */ #define MI_BCNCANCLD (1 << 4) /* end of ATIM-window (IBSS) */ #define MI_ATIMWINEND (1 << 5) /* PMQ entries available */ #define MI_PMQ (1 << 6) /* non-specific gen-stat bits that are set by PSM */ #define MI_NSPECGEN_0 (1 << 7) /* non-specific gen-stat bits that are set by PSM */ #define MI_NSPECGEN_1 (1 << 8) /* MAC level Tx error */ #define MI_MACTXERR (1 << 9) /* non-specific gen-stat bits that are set by PSM */ #define MI_NSPECGEN_3 (1 << 10) /* PHY Tx error */ #define MI_PHYTXERR (1 << 11) /* Power Management Event */ #define MI_PME (1 << 12) /* General-purpose timer0 */ #define MI_GP0 (1 << 13) /* General-purpose timer1 */ #define MI_GP1 (1 << 14) /* (ORed) DMA-interrupts */ #define MI_DMAINT (1 << 15) /* MAC has completed a TX FIFO Suspend/Flush */ #define MI_TXSTOP (1 << 16) /* MAC has completed a CCA measurement */ #define MI_CCA (1 << 17) /* MAC has collected background noise samples */ #define MI_BG_NOISE (1 << 18) /* MBSS DTIM TBTT indication */ #define MI_DTIM_TBTT (1 << 19) /* Probe response queue needs attention */ #define MI_PRQ (1 << 20) /* Radio/PHY has been powered back up. */ #define MI_PWRUP (1 << 21) #define MI_RESERVED3 (1 << 22) #define MI_RESERVED2 (1 << 23) #define MI_RESERVED1 (1 << 25) /* MAC detected change on RF Disable input*/ #define MI_RFDISABLE (1 << 28) /* MAC has completed a TX */ #define MI_TFS (1 << 29) /* A phy status change wrt G mode */ #define MI_PHYCHANGED (1 << 30) /* general purpose timeout */ #define MI_TO (1U << 31) /* Mac capabilities registers */ /*== machwcap ==*/ #define MCAP_TKIPMIC 0x80000000 /* TKIP MIC hardware present */ /*== pmqhost data ==*/ /* data entry of head pmq entry */ #define PMQH_DATA_MASK 0xffff0000 /* PM entry for BSS config */ #define PMQH_BSSCFG 0x00100000 /* PM Mode OFF: power save off */ #define PMQH_PMOFF 0x00010000 /* PM Mode ON: power save on */ #define PMQH_PMON 0x00020000 /* Dis-associated or De-authenticated */ #define PMQH_DASAT 0x00040000 /* ATIM not acknowledged */ #define PMQH_ATIMFAIL 0x00080000 /* delete head entry */ #define PMQH_DEL_ENTRY 0x00000001 /* delete head entry to cur read pointer -1 */ #define PMQH_DEL_MULT 0x00000002 /* pmq overflow indication */ #define PMQH_OFLO 0x00000004 /* entries are present in pmq */ #define PMQH_NOT_EMPTY 0x00000008 /*== phydebug ==*/ /* phy is asserting carrier sense */ #define PDBG_CRS (1 << 0) /* phy is taking xmit byte from mac this cycle */ #define PDBG_TXA (1 << 1) /* mac is instructing the phy to transmit a frame */ #define PDBG_TXF (1 << 2) /* phy is signalling a transmit Error to the mac */ #define PDBG_TXE (1 << 3) /* phy detected the end of a valid frame preamble */ #define PDBG_RXF (1 << 4) /* phy detected the end of a valid PLCP header */ #define PDBG_RXS (1 << 5) /* rx start not asserted */ #define PDBG_RXFRG (1 << 6) /* mac is taking receive byte from phy this cycle */ #define PDBG_RXV (1 << 7) /* RF portion of the radio is disabled */ #define PDBG_RFD (1 << 16) /*== objaddr register ==*/ #define OBJADDR_SEL_MASK 0x000F0000 #define OBJADDR_UCM_SEL 0x00000000 #define OBJADDR_SHM_SEL 0x00010000 #define OBJADDR_SCR_SEL 0x00020000 #define OBJADDR_IHR_SEL 0x00030000 #define OBJADDR_RCMTA_SEL 0x00040000 #define OBJADDR_SRCHM_SEL 0x00060000 #define OBJADDR_WINC 0x01000000 #define OBJADDR_RINC 0x02000000 #define OBJADDR_AUTO_INC 0x03000000 #define WEP_PCMADDR 0x07d4 #define WEP_PCMDATA 0x07d6 /*== frmtxstatus ==*/ #define TXS_V (1 << 0) /* valid bit */ #define TXS_STATUS_MASK 0xffff #define TXS_FID_MASK 0xffff0000 #define TXS_FID_SHIFT 16 /*== frmtxstatus2 ==*/ #define TXS_SEQ_MASK 0xffff #define TXS_PTX_MASK 0xff0000 #define TXS_PTX_SHIFT 16 #define TXS_MU_MASK 0x01000000 #define TXS_MU_SHIFT 24 /*== clk_ctl_st ==*/ #define CCS_ERSRC_REQ_D11PLL 0x00000100 /* d11 core pll request */ #define CCS_ERSRC_REQ_PHYPLL 0x00000200 /* PHY pll request */ #define CCS_ERSRC_AVAIL_D11PLL 0x01000000 /* d11 core pll available */ #define CCS_ERSRC_AVAIL_PHYPLL 0x02000000 /* PHY pll available */ /* HT Cloclk Ctrl and Clock Avail for 4313 */ #define CCS_ERSRC_REQ_HT 0x00000010 /* HT avail request */ #define CCS_ERSRC_AVAIL_HT 0x00020000 /* HT clock available */ /* tsf_cfprep register */ #define CFPREP_CBI_MASK 0xffffffc0 #define CFPREP_CBI_SHIFT 6 #define CFPREP_CFPP 0x00000001 /* tx fifo sizes values are in terms of 256 byte blocks */ #define TXFIFOCMD_RESET_MASK (1 << 15) /* reset */ #define TXFIFOCMD_FIFOSEL_SHIFT 8 /* fifo */ #define TXFIFO_FIFOTOP_SHIFT 8 /* fifo start */ #define TXFIFO_START_BLK16 65 /* Base address + 32 * 512 B/P */ #define TXFIFO_START_BLK 6 /* Base address + 6 * 256 B */ #define TXFIFO_SIZE_UNIT 256 /* one unit corresponds to 256 bytes */ #define MBSS16_TEMPLMEM_MINBLKS 65 /* one unit corresponds to 256 bytes */ /*== phy versions (PhyVersion:Revision field) ==*/ /* analog block version */ #define PV_AV_MASK 0xf000 /* analog block version bitfield offset */ #define PV_AV_SHIFT 12 /* phy type */ #define PV_PT_MASK 0x0f00 /* phy type bitfield offset */ #define PV_PT_SHIFT 8 /* phy version */ #define PV_PV_MASK 0x000f #define PHY_TYPE(v) ((v & PV_PT_MASK) >> PV_PT_SHIFT) /*== phy types (PhyVersion:PhyType field) ==*/ #define PHY_TYPE_N 4 /* N-Phy value */ #define PHY_TYPE_SSN 6 /* SSLPN-Phy value */ #define PHY_TYPE_LCN 8 /* LCN-Phy value */ #define PHY_TYPE_LCNXN 9 /* LCNXN-Phy value */ #define PHY_TYPE_NULL 0xf /* Invalid Phy value */ /*== analog types (PhyVersion:AnalogType field) ==*/ #define ANA_11N_013 5 /* 802.11a PLCP header def */ struct ofdm_phy_hdr { u8 rlpt[3]; /* rate, length, parity, tail */ u16 service; u8 pad; } __packed; #define D11A_PHY_HDR_GRATE(phdr) ((phdr)->rlpt[0] & 0x0f) #define D11A_PHY_HDR_GRES(phdr) (((phdr)->rlpt[0] >> 4) & 0x01) #define D11A_PHY_HDR_GLENGTH(phdr) (((u32 *)((phdr)->rlpt) >> 5) & 0x0fff) #define D11A_PHY_HDR_GPARITY(phdr) (((phdr)->rlpt[3] >> 1) & 0x01) #define D11A_PHY_HDR_GTAIL(phdr) (((phdr)->rlpt[3] >> 2) & 0x3f) /* rate encoded per 802.11a-1999 sec 17.3.4.1 */ #define D11A_PHY_HDR_SRATE(phdr, rate) \ ((phdr)->rlpt[0] = ((phdr)->rlpt[0] & 0xf0) | ((rate) & 0xf)) /* set reserved field to zero */ #define D11A_PHY_HDR_SRES(phdr) ((phdr)->rlpt[0] &= 0xef) /* length is number of octets in PSDU */ #define D11A_PHY_HDR_SLENGTH(phdr, length) \ (*(u32 *)((phdr)->rlpt) = *(u32 *)((phdr)->rlpt) | \ (((length) & 0x0fff) << 5)) /* set the tail to all zeros */ #define D11A_PHY_HDR_STAIL(phdr) ((phdr)->rlpt[3] &= 0x03) #define D11A_PHY_HDR_LEN_L 3 /* low-rate part of PLCP header */ #define D11A_PHY_HDR_LEN_R 2 /* high-rate part of PLCP header */ #define D11A_PHY_TX_DELAY (2) /* 2.1 usec */ #define D11A_PHY_HDR_TIME (4) /* low-rate part of PLCP header */ #define D11A_PHY_PRE_TIME (16) #define D11A_PHY_PREHDR_TIME (D11A_PHY_PRE_TIME + D11A_PHY_HDR_TIME) /* 802.11b PLCP header def */ struct cck_phy_hdr { u8 signal; u8 service; u16 length; u16 crc; } __packed; #define D11B_PHY_HDR_LEN 6 #define D11B_PHY_TX_DELAY (3) /* 3.4 usec */ #define D11B_PHY_LHDR_TIME (D11B_PHY_HDR_LEN << 3) #define D11B_PHY_LPRE_TIME (144) #define D11B_PHY_LPREHDR_TIME (D11B_PHY_LPRE_TIME + D11B_PHY_LHDR_TIME) #define D11B_PHY_SHDR_TIME (D11B_PHY_LHDR_TIME >> 1) #define D11B_PHY_SPRE_TIME (D11B_PHY_LPRE_TIME >> 1) #define D11B_PHY_SPREHDR_TIME (D11B_PHY_SPRE_TIME + D11B_PHY_SHDR_TIME) #define D11B_PLCP_SIGNAL_LOCKED (1 << 2) #define D11B_PLCP_SIGNAL_LE (1 << 7) #define MIMO_PLCP_MCS_MASK 0x7f /* mcs index */ #define MIMO_PLCP_40MHZ 0x80 /* 40 Hz frame */ #define MIMO_PLCP_AMPDU 0x08 /* ampdu */ #define BRCMS_GET_CCK_PLCP_LEN(plcp) (plcp[4] + (plcp[5] << 8)) #define BRCMS_GET_MIMO_PLCP_LEN(plcp) (plcp[1] + (plcp[2] << 8)) #define BRCMS_SET_MIMO_PLCP_LEN(plcp, len) \ do { \ plcp[1] = len & 0xff; \ plcp[2] = ((len >> 8) & 0xff); \ } while (0); #define BRCMS_SET_MIMO_PLCP_AMPDU(plcp) (plcp[3] |= MIMO_PLCP_AMPDU) #define BRCMS_CLR_MIMO_PLCP_AMPDU(plcp) (plcp[3] &= ~MIMO_PLCP_AMPDU) #define BRCMS_IS_MIMO_PLCP_AMPDU(plcp) (plcp[3] & MIMO_PLCP_AMPDU) /* * The dot11a PLCP header is 5 bytes. To simplify the software (so that we * don't need e.g. different tx DMA headers for 11a and 11b), the PLCP header * has padding added in the ucode. */ #define D11_PHY_HDR_LEN 6 /* TX DMA buffer header */ struct d11txh { __le16 MacTxControlLow; /* 0x0 */ __le16 MacTxControlHigh; /* 0x1 */ __le16 MacFrameControl; /* 0x2 */ __le16 TxFesTimeNormal; /* 0x3 */ __le16 PhyTxControlWord; /* 0x4 */ __le16 PhyTxControlWord_1; /* 0x5 */ __le16 PhyTxControlWord_1_Fbr; /* 0x6 */ __le16 PhyTxControlWord_1_Rts; /* 0x7 */ __le16 PhyTxControlWord_1_FbrRts; /* 0x8 */ __le16 MainRates; /* 0x9 */ __le16 XtraFrameTypes; /* 0xa */ u8 IV[16]; /* 0x0b - 0x12 */ u8 TxFrameRA[6]; /* 0x13 - 0x15 */ __le16 TxFesTimeFallback; /* 0x16 */ u8 RTSPLCPFallback[6]; /* 0x17 - 0x19 */ __le16 RTSDurFallback; /* 0x1a */ u8 FragPLCPFallback[6]; /* 0x1b - 1d */ __le16 FragDurFallback; /* 0x1e */ __le16 MModeLen; /* 0x1f */ __le16 MModeFbrLen; /* 0x20 */ __le16 TstampLow; /* 0x21 */ __le16 TstampHigh; /* 0x22 */ __le16 ABI_MimoAntSel; /* 0x23 */ __le16 PreloadSize; /* 0x24 */ __le16 AmpduSeqCtl; /* 0x25 */ __le16 TxFrameID; /* 0x26 */ __le16 TxStatus; /* 0x27 */ __le16 MaxNMpdus; /* 0x28 */ __le16 MaxABytes_MRT; /* 0x29 */ __le16 MaxABytes_FBR; /* 0x2a */ __le16 MinMBytes; /* 0x2b */ u8 RTSPhyHeader[D11_PHY_HDR_LEN]; /* 0x2c - 0x2e */ struct ieee80211_rts rts_frame; /* 0x2f - 0x36 */ u16 PAD; /* 0x37 */ } __packed; #define D11_TXH_LEN 112 /* bytes */ /* Frame Types */ #define FT_CCK 0 #define FT_OFDM 1 #define FT_HT 2 #define FT_N 3 /* * Position of MPDU inside A-MPDU; indicated with bits 10:9 * of MacTxControlLow */ #define TXC_AMPDU_SHIFT 9 /* shift for ampdu settings */ #define TXC_AMPDU_NONE 0 /* Regular MPDU, not an A-MPDU */ #define TXC_AMPDU_FIRST 1 /* first MPDU of an A-MPDU */ #define TXC_AMPDU_MIDDLE 2 /* intermediate MPDU of an A-MPDU */ #define TXC_AMPDU_LAST 3 /* last (or single) MPDU of an A-MPDU */ /*== MacTxControlLow ==*/ #define TXC_AMIC 0x8000 #define TXC_SENDCTS 0x0800 #define TXC_AMPDU_MASK 0x0600 #define TXC_BW_40 0x0100 #define TXC_FREQBAND_5G 0x0080 #define TXC_DFCS 0x0040 #define TXC_IGNOREPMQ 0x0020 #define TXC_HWSEQ 0x0010 #define TXC_STARTMSDU 0x0008 #define TXC_SENDRTS 0x0004 #define TXC_LONGFRAME 0x0002 #define TXC_IMMEDACK 0x0001 /*== MacTxControlHigh ==*/ /* RTS fallback preamble type 1 = SHORT 0 = LONG */ #define TXC_PREAMBLE_RTS_FB_SHORT 0x8000 /* RTS main rate preamble type 1 = SHORT 0 = LONG */ #define TXC_PREAMBLE_RTS_MAIN_SHORT 0x4000 /* * Main fallback rate preamble type * 1 = SHORT for OFDM/GF for MIMO * 0 = LONG for CCK/MM for MIMO */ #define TXC_PREAMBLE_DATA_FB_SHORT 0x2000 /* TXC_PREAMBLE_DATA_MAIN is in PhyTxControl bit 5 */ /* use fallback rate for this AMPDU */ #define TXC_AMPDU_FBR 0x1000 #define TXC_SECKEY_MASK 0x0FF0 #define TXC_SECKEY_SHIFT 4 /* Use alternate txpwr defined at loc. M_ALT_TXPWR_IDX */ #define TXC_ALT_TXPWR 0x0008 #define TXC_SECTYPE_MASK 0x0007 #define TXC_SECTYPE_SHIFT 0 /* Null delimiter for Fallback rate */ #define AMPDU_FBR_NULL_DELIM 5 /* Location of Null delimiter count for AMPDU */ /* PhyTxControl for Mimophy */ #define PHY_TXC_PWR_MASK 0xFC00 #define PHY_TXC_PWR_SHIFT 10 #define PHY_TXC_ANT_MASK 0x03C0 /* bit 6, 7, 8, 9 */ #define PHY_TXC_ANT_SHIFT 6 #define PHY_TXC_ANT_0_1 0x00C0 /* auto, last rx */ #define PHY_TXC_LCNPHY_ANT_LAST 0x0000 #define PHY_TXC_ANT_3 0x0200 /* virtual antenna 3 */ #define PHY_TXC_ANT_2 0x0100 /* virtual antenna 2 */ #define PHY_TXC_ANT_1 0x0080 /* virtual antenna 1 */ #define PHY_TXC_ANT_0 0x0040 /* virtual antenna 0 */ #define PHY_TXC_SHORT_HDR 0x0010 #define PHY_TXC_OLD_ANT_0 0x0000 #define PHY_TXC_OLD_ANT_1 0x0100 #define PHY_TXC_OLD_ANT_LAST 0x0300 /* PhyTxControl_1 for Mimophy */ #define PHY_TXC1_BW_MASK 0x0007 #define PHY_TXC1_BW_10MHZ 0 #define PHY_TXC1_BW_10MHZ_UP 1 #define PHY_TXC1_BW_20MHZ 2 #define PHY_TXC1_BW_20MHZ_UP 3 #define PHY_TXC1_BW_40MHZ 4 #define PHY_TXC1_BW_40MHZ_DUP 5 #define PHY_TXC1_MODE_SHIFT 3 #define PHY_TXC1_MODE_MASK 0x0038 #define PHY_TXC1_MODE_SISO 0 #define PHY_TXC1_MODE_CDD 1 #define PHY_TXC1_MODE_STBC 2 #define PHY_TXC1_MODE_SDM 3 /* PhyTxControl for HTphy that are different from Mimophy */ #define PHY_TXC_HTANT_MASK 0x3fC0 /* bits 6-13 */ /* XtraFrameTypes */ #define XFTS_RTS_FT_SHIFT 2 #define XFTS_FBRRTS_FT_SHIFT 4 #define XFTS_CHANNEL_SHIFT 8 /* Antenna diversity bit in ant_wr_settle */ #define PHY_AWS_ANTDIV 0x2000 /* IFS ctl */ #define IFS_USEEDCF (1 << 2) /* IFS ctl1 */ #define IFS_CTL1_EDCRS (1 << 3) #define IFS_CTL1_EDCRS_20L (1 << 4) #define IFS_CTL1_EDCRS_40 (1 << 5) /* ABI_MimoAntSel */ #define ABI_MAS_ADDR_BMP_IDX_MASK 0x0f00 #define ABI_MAS_ADDR_BMP_IDX_SHIFT 8 #define ABI_MAS_FBR_ANT_PTN_MASK 0x00f0 #define ABI_MAS_FBR_ANT_PTN_SHIFT 4 #define ABI_MAS_MRT_ANT_PTN_MASK 0x000f /* tx status packet */ struct tx_status { u16 framelen; u16 PAD; u16 frameid; u16 status; u16 lasttxtime; u16 sequence; u16 phyerr; u16 ackphyrxsh; } __packed; #define TXSTATUS_LEN 16 /* status field bit definitions */ #define TX_STATUS_FRM_RTX_MASK 0xF000 #define TX_STATUS_FRM_RTX_SHIFT 12 #define TX_STATUS_RTS_RTX_MASK 0x0F00 #define TX_STATUS_RTS_RTX_SHIFT 8 #define TX_STATUS_MASK 0x00FE #define TX_STATUS_PMINDCTD (1 << 7) /* PM mode indicated to AP */ #define TX_STATUS_INTERMEDIATE (1 << 6) /* intermediate or 1st ampdu pkg */ #define TX_STATUS_AMPDU (1 << 5) /* AMPDU status */ #define TX_STATUS_SUPR_MASK 0x1C /* suppress status bits (4:2) */ #define TX_STATUS_SUPR_SHIFT 2 #define TX_STATUS_ACK_RCV (1 << 1) /* ACK received */ #define TX_STATUS_VALID (1 << 0) /* Tx status valid */ #define TX_STATUS_NO_ACK 0 /* suppress status reason codes */ #define TX_STATUS_SUPR_PMQ (1 << 2) /* PMQ entry */ #define TX_STATUS_SUPR_FLUSH (2 << 2) /* flush request */ #define TX_STATUS_SUPR_FRAG (3 << 2) /* previous frag failure */ #define TX_STATUS_SUPR_TBTT (3 << 2) /* SHARED: Probe resp supr for TBTT */ #define TX_STATUS_SUPR_BADCH (4 << 2) /* channel mismatch */ #define TX_STATUS_SUPR_EXPTIME (5 << 2) /* lifetime expiry */ #define TX_STATUS_SUPR_UF (6 << 2) /* underflow */ /* Unexpected tx status for rate update */ #define TX_STATUS_UNEXP(status) \ ((((status) & TX_STATUS_INTERMEDIATE) != 0) && \ TX_STATUS_UNEXP_AMPDU(status)) /* Unexpected tx status for A-MPDU rate update */ #define TX_STATUS_UNEXP_AMPDU(status) \ ((((status) & TX_STATUS_SUPR_MASK) != 0) && \ (((status) & TX_STATUS_SUPR_MASK) != TX_STATUS_SUPR_EXPTIME)) #define TX_STATUS_BA_BMAP03_MASK 0xF000 /* ba bitmap 0:3 in 1st pkg */ #define TX_STATUS_BA_BMAP03_SHIFT 12 /* ba bitmap 0:3 in 1st pkg */ #define TX_STATUS_BA_BMAP47_MASK 0x001E /* ba bitmap 4:7 in 2nd pkg */ #define TX_STATUS_BA_BMAP47_SHIFT 3 /* ba bitmap 4:7 in 2nd pkg */ /* RXE (Receive Engine) */ /* RCM_CTL */ #define RCM_INC_MASK_H 0x0080 #define RCM_INC_MASK_L 0x0040 #define RCM_INC_DATA 0x0020 #define RCM_INDEX_MASK 0x001F #define RCM_SIZE 15 #define RCM_MAC_OFFSET 0 /* current MAC address */ #define RCM_BSSID_OFFSET 3 /* current BSSID address */ #define RCM_F_BSSID_0_OFFSET 6 /* foreign BSS CFP tracking */ #define RCM_F_BSSID_1_OFFSET 9 /* foreign BSS CFP tracking */ #define RCM_F_BSSID_2_OFFSET 12 /* foreign BSS CFP tracking */ #define RCM_WEP_TA0_OFFSET 16 #define RCM_WEP_TA1_OFFSET 19 #define RCM_WEP_TA2_OFFSET 22 #define RCM_WEP_TA3_OFFSET 25 /* PSM Block */ /* psm_phy_hdr_param bits */ #define MAC_PHY_RESET 1 #define MAC_PHY_CLOCK_EN 2 #define MAC_PHY_FORCE_CLK 4 /* WEP Block */ /* WEP_WKEY */ #define WKEY_START (1 << 8) #define WKEY_SEL_MASK 0x1F /* WEP data formats */ /* the number of RCMTA entries */ #define RCMTA_SIZE 50 #define M_ADDR_BMP_BLK (0x37e * 2) #define M_ADDR_BMP_BLK_SZ 12 #define ADDR_BMP_RA (1 << 0) /* Receiver Address (RA) */ #define ADDR_BMP_TA (1 << 1) /* Transmitter Address (TA) */ #define ADDR_BMP_BSSID (1 << 2) /* BSSID */ #define ADDR_BMP_AP (1 << 3) /* Infra-BSS Access Point */ #define ADDR_BMP_STA (1 << 4) /* Infra-BSS Station */ #define ADDR_BMP_RESERVED1 (1 << 5) #define ADDR_BMP_RESERVED2 (1 << 6) #define ADDR_BMP_RESERVED3 (1 << 7) #define ADDR_BMP_BSS_IDX_MASK (3 << 8) /* BSS control block index */ #define ADDR_BMP_BSS_IDX_SHIFT 8 #define WSEC_MAX_RCMTA_KEYS 54 /* max keys in M_TKMICKEYS_BLK */ #define WSEC_MAX_TKMIC_ENGINE_KEYS 12 /* 8 + 4 default */ /* max RXE match registers */ #define WSEC_MAX_RXE_KEYS 4 /* SECKINDXALGO (Security Key Index & Algorithm Block) word format */ /* SKL (Security Key Lookup) */ #define SKL_ALGO_MASK 0x0007 #define SKL_ALGO_SHIFT 0 #define SKL_KEYID_MASK 0x0008 #define SKL_KEYID_SHIFT 3 #define SKL_INDEX_MASK 0x03F0 #define SKL_INDEX_SHIFT 4 #define SKL_GRP_ALGO_MASK 0x1c00 #define SKL_GRP_ALGO_SHIFT 10 /* additional bits defined for IBSS group key support */ #define SKL_IBSS_INDEX_MASK 0x01F0 #define SKL_IBSS_INDEX_SHIFT 4 #define SKL_IBSS_KEYID1_MASK 0x0600 #define SKL_IBSS_KEYID1_SHIFT 9 #define SKL_IBSS_KEYID2_MASK 0x1800 #define SKL_IBSS_KEYID2_SHIFT 11 #define SKL_IBSS_KEYALGO_MASK 0xE000 #define SKL_IBSS_KEYALGO_SHIFT 13 #define WSEC_MODE_OFF 0 #define WSEC_MODE_HW 1 #define WSEC_MODE_SW 2 #define WSEC_ALGO_OFF 0 #define WSEC_ALGO_WEP1 1 #define WSEC_ALGO_TKIP 2 #define WSEC_ALGO_AES 3 #define WSEC_ALGO_WEP128 4 #define WSEC_ALGO_AES_LEGACY 5 #define WSEC_ALGO_NALG 6 #define AES_MODE_NONE 0 #define AES_MODE_CCM 1 /* WEP_CTL (Rev 0) */ #define WECR0_KEYREG_SHIFT 0 #define WECR0_KEYREG_MASK 0x7 #define WECR0_DECRYPT (1 << 3) #define WECR0_IVINLINE (1 << 4) #define WECR0_WEPALG_SHIFT 5 #define WECR0_WEPALG_MASK (0x7 << 5) #define WECR0_WKEYSEL_SHIFT 8 #define WECR0_WKEYSEL_MASK (0x7 << 8) #define WECR0_WKEYSTART (1 << 11) #define WECR0_WEPINIT (1 << 14) #define WECR0_ICVERR (1 << 15) /* Frame template map byte offsets */ #define T_ACTS_TPL_BASE (0) #define T_NULL_TPL_BASE (0xc * 2) #define T_QNULL_TPL_BASE (0x1c * 2) #define T_RR_TPL_BASE (0x2c * 2) #define T_BCN0_TPL_BASE (0x34 * 2) #define T_PRS_TPL_BASE (0x134 * 2) #define T_BCN1_TPL_BASE (0x234 * 2) #define T_TX_FIFO_TXRAM_BASE (T_ACTS_TPL_BASE + \ (TXFIFO_START_BLK * TXFIFO_SIZE_UNIT)) #define T_BA_TPL_BASE T_QNULL_TPL_BASE /* template area for BA */ #define T_RAM_ACCESS_SZ 4 /* template ram is 4 byte access only */ /* Shared Mem byte offsets */ /* Location where the ucode expects the corerev */ #define M_MACHW_VER (0x00b * 2) /* Location where the ucode expects the MAC capabilities */ #define M_MACHW_CAP_L (0x060 * 2) #define M_MACHW_CAP_H (0x061 * 2) /* WME shared memory */ #define M_EDCF_STATUS_OFF (0x007 * 2) #define M_TXF_CUR_INDEX (0x018 * 2) #define M_EDCF_QINFO (0x120 * 2) /* PS-mode related parameters */ #define M_DOT11_SLOT (0x008 * 2) #define M_DOT11_DTIMPERIOD (0x009 * 2) #define M_NOSLPZNATDTIM (0x026 * 2) /* Beacon-related parameters */ #define M_BCN0_FRM_BYTESZ (0x00c * 2) /* Bcn 0 template length */ #define M_BCN1_FRM_BYTESZ (0x00d * 2) /* Bcn 1 template length */ #define M_BCN_TXTSF_OFFSET (0x00e * 2) #define M_TIMBPOS_INBEACON (0x00f * 2) #define M_SFRMTXCNTFBRTHSD (0x022 * 2) #define M_LFRMTXCNTFBRTHSD (0x023 * 2) #define M_BCN_PCTLWD (0x02a * 2) #define M_BCN_LI (0x05b * 2) /* beacon listen interval */ /* MAX Rx Frame len */ #define M_MAXRXFRM_LEN (0x010 * 2) /* ACK/CTS related params */ #define M_RSP_PCTLWD (0x011 * 2) /* Hardware Power Control */ #define M_TXPWR_N (0x012 * 2) #define M_TXPWR_TARGET (0x013 * 2) #define M_TXPWR_MAX (0x014 * 2) #define M_TXPWR_CUR (0x019 * 2) /* Rx-related parameters */ #define M_RX_PAD_DATA_OFFSET (0x01a * 2) /* WEP Shared mem data */ #define M_SEC_DEFIVLOC (0x01e * 2) #define M_SEC_VALNUMSOFTMCHTA (0x01f * 2) #define M_PHYVER (0x028 * 2) #define M_PHYTYPE (0x029 * 2) #define M_SECRXKEYS_PTR (0x02b * 2) #define M_TKMICKEYS_PTR (0x059 * 2) #define M_SECKINDXALGO_BLK (0x2ea * 2) #define M_SECKINDXALGO_BLK_SZ 54 #define M_SECPSMRXTAMCH_BLK (0x2fa * 2) #define M_TKIP_TSC_TTAK (0x18c * 2) #define D11_MAX_KEY_SIZE 16 #define M_MAX_ANTCNT (0x02e * 2) /* antenna swap threshold */ /* Probe response related parameters */ #define M_SSIDLEN (0x024 * 2) #define M_PRB_RESP_FRM_LEN (0x025 * 2) #define M_PRS_MAXTIME (0x03a * 2) #define M_SSID (0xb0 * 2) #define M_CTXPRS_BLK (0xc0 * 2) #define C_CTX_PCTLWD_POS (0x4 * 2) /* Delta between OFDM and CCK power in CCK power boost mode */ #define M_OFDM_OFFSET (0x027 * 2) /* TSSI for last 4 11b/g CCK packets transmitted */ #define M_B_TSSI_0 (0x02c * 2) #define M_B_TSSI_1 (0x02d * 2) /* Host flags to turn on ucode options */ #define M_HOST_FLAGS1 (0x02f * 2) #define M_HOST_FLAGS2 (0x030 * 2) #define M_HOST_FLAGS3 (0x031 * 2) #define M_HOST_FLAGS4 (0x03c * 2) #define M_HOST_FLAGS5 (0x06a * 2) #define M_HOST_FLAGS_SZ 16 #define M_RADAR_REG (0x033 * 2) /* TSSI for last 4 11a OFDM packets transmitted */ #define M_A_TSSI_0 (0x034 * 2) #define M_A_TSSI_1 (0x035 * 2) /* noise interference measurement */ #define M_NOISE_IF_COUNT (0x034 * 2) #define M_NOISE_IF_TIMEOUT (0x035 * 2) #define M_RF_RX_SP_REG1 (0x036 * 2) /* TSSI for last 4 11g OFDM packets transmitted */ #define M_G_TSSI_0 (0x038 * 2) #define M_G_TSSI_1 (0x039 * 2) /* Background noise measure */ #define M_JSSI_0 (0x44 * 2) #define M_JSSI_1 (0x45 * 2) #define M_JSSI_AUX (0x46 * 2) #define M_CUR_2050_RADIOCODE (0x47 * 2) /* TX fifo sizes */ #define M_FIFOSIZE0 (0x4c * 2) #define M_FIFOSIZE1 (0x4d * 2) #define M_FIFOSIZE2 (0x4e * 2) #define M_FIFOSIZE3 (0x4f * 2) #define D11_MAX_TX_FRMS 32 /* max frames allowed in tx fifo */ /* Current channel number plus upper bits */ #define M_CURCHANNEL (0x50 * 2) #define D11_CURCHANNEL_5G 0x0100; #define D11_CURCHANNEL_40 0x0200; #define D11_CURCHANNEL_MAX 0x00FF; /* last posted frameid on the bcmc fifo */ #define M_BCMC_FID (0x54 * 2) #define INVALIDFID 0xffff /* extended beacon phyctl bytes for 11N */ #define M_BCN_PCTL1WD (0x058 * 2) /* idle busy ratio to duty_cycle requirement */ #define M_TX_IDLE_BUSY_RATIO_X_16_CCK (0x52 * 2) #define M_TX_IDLE_BUSY_RATIO_X_16_OFDM (0x5A * 2) /* CW RSSI for LCNPHY */ #define M_LCN_RSSI_0 0x1332 #define M_LCN_RSSI_1 0x1338 #define M_LCN_RSSI_2 0x133e #define M_LCN_RSSI_3 0x1344 /* SNR for LCNPHY */ #define M_LCN_SNR_A_0 0x1334 #define M_LCN_SNR_B_0 0x1336 #define M_LCN_SNR_A_1 0x133a #define M_LCN_SNR_B_1 0x133c #define M_LCN_SNR_A_2 0x1340 #define M_LCN_SNR_B_2 0x1342 #define M_LCN_SNR_A_3 0x1346 #define M_LCN_SNR_B_3 0x1348 #define M_LCN_LAST_RESET (81*2) #define M_LCN_LAST_LOC (63*2) #define M_LCNPHY_RESET_STATUS (4902) #define M_LCNPHY_DSC_TIME (0x98d*2) #define M_LCNPHY_RESET_CNT_DSC (0x98b*2) #define M_LCNPHY_RESET_CNT (0x98c*2) /* Rate table offsets */ #define M_RT_DIRMAP_A (0xe0 * 2) #define M_RT_BBRSMAP_A (0xf0 * 2) #define M_RT_DIRMAP_B (0x100 * 2) #define M_RT_BBRSMAP_B (0x110 * 2) /* Rate table entry offsets */ #define M_RT_PRS_PLCP_POS 10 #define M_RT_PRS_DUR_POS 16 #define M_RT_OFDM_PCTL1_POS 18 #define M_20IN40_IQ (0x380 * 2) /* SHM locations where ucode stores the current power index */ #define M_CURR_IDX1 (0x384 * 2) #define M_CURR_IDX2 (0x387 * 2) #define M_BSCALE_ANT0 (0x5e * 2) #define M_BSCALE_ANT1 (0x5f * 2) /* Antenna Diversity Testing */ #define M_MIMO_ANTSEL_RXDFLT (0x63 * 2) #define M_ANTSEL_CLKDIV (0x61 * 2) #define M_MIMO_ANTSEL_TXDFLT (0x64 * 2) #define M_MIMO_MAXSYM (0x5d * 2) #define MIMO_MAXSYM_DEF 0x8000 /* 32k */ #define MIMO_MAXSYM_MAX 0xffff /* 64k */ #define M_WATCHDOG_8TU (0x1e * 2) #define WATCHDOG_8TU_DEF 5 #define WATCHDOG_8TU_MAX 10 /* Manufacturing Test Variables */ /* PER test mode */ #define M_PKTENG_CTRL (0x6c * 2) /* IFS for TX mode */ #define M_PKTENG_IFS (0x6d * 2) /* Lower word of tx frmcnt/rx lostcnt */ #define M_PKTENG_FRMCNT_LO (0x6e * 2) /* Upper word of tx frmcnt/rx lostcnt */ #define M_PKTENG_FRMCNT_HI (0x6f * 2) /* Index variation in vbat ripple */ #define M_LCN_PWR_IDX_MAX (0x67 * 2) /* highest index read by ucode */ #define M_LCN_PWR_IDX_MIN (0x66 * 2) /* lowest index read by ucode */ /* M_PKTENG_CTRL bit definitions */ #define M_PKTENG_MODE_TX 0x0001 #define M_PKTENG_MODE_TX_RIFS 0x0004 #define M_PKTENG_MODE_TX_CTS 0x0008 #define M_PKTENG_MODE_RX 0x0002 #define M_PKTENG_MODE_RX_WITH_ACK 0x0402 #define M_PKTENG_MODE_MASK 0x0003 /* TX frames indicated in the frmcnt reg */ #define M_PKTENG_FRMCNT_VLD 0x0100 /* Sample Collect parameters (bitmap and type) */ /* Trigger bitmap for sample collect */ #define M_SMPL_COL_BMP (0x37d * 2) /* Sample collect type */ #define M_SMPL_COL_CTL (0x3b2 * 2) #define ANTSEL_CLKDIV_4MHZ 6 #define MIMO_ANTSEL_BUSY 0x4000 /* bit 14 (busy) */ #define MIMO_ANTSEL_SEL 0x8000 /* bit 15 write the value */ #define MIMO_ANTSEL_WAIT 50 /* 50us wait */ #define MIMO_ANTSEL_OVERRIDE 0x8000 /* flag */ struct shm_acparams { u16 txop; u16 cwmin; u16 cwmax; u16 cwcur; u16 aifs; u16 bslots; u16 reggap; u16 status; u16 rsvd[8]; } __packed; #define M_EDCF_QLEN (16 * 2) #define WME_STATUS_NEWAC (1 << 8) /* M_HOST_FLAGS */ #define MHFMAX 5 /* Number of valid hostflag half-word (u16) */ #define MHF1 0 /* Hostflag 1 index */ #define MHF2 1 /* Hostflag 2 index */ #define MHF3 2 /* Hostflag 3 index */ #define MHF4 3 /* Hostflag 4 index */ #define MHF5 4 /* Hostflag 5 index */ /* Flags in M_HOST_FLAGS */ /* Enable ucode antenna diversity help */ #define MHF1_ANTDIV 0x0001 /* Enable EDCF access control */ #define MHF1_EDCF 0x0100 #define MHF1_IQSWAP_WAR 0x0200 /* Disable Slow clock request, for corerev < 11 */ #define MHF1_FORCEFASTCLK 0x0400 /* Flags in M_HOST_FLAGS2 */ /* Flush BCMC FIFO immediately */ #define MHF2_TXBCMC_NOW 0x0040 /* Enable ucode/hw power control */ #define MHF2_HWPWRCTL 0x0080 #define MHF2_NPHY40MHZ_WAR 0x0800 /* Flags in M_HOST_FLAGS3 */ /* enabled mimo antenna selection */ #define MHF3_ANTSEL_EN 0x0001 /* antenna selection mode: 0: 2x3, 1: 2x4 */ #define MHF3_ANTSEL_MODE 0x0002 #define MHF3_RESERVED1 0x0004 #define MHF3_RESERVED2 0x0008 #define MHF3_NPHY_MLADV_WAR 0x0010 /* Flags in M_HOST_FLAGS4 */ /* force bphy Tx on core 0 (board level WAR) */ #define MHF4_BPHY_TXCORE0 0x0080 /* for 4313A0 FEM boards */ #define MHF4_EXTPA_ENABLE 0x4000 /* Flags in M_HOST_FLAGS5 */ #define MHF5_4313_GPIOCTRL 0x0001 #define MHF5_RESERVED1 0x0002 #define MHF5_RESERVED2 0x0004 /* Radio power setting for ucode */ #define M_RADIO_PWR (0x32 * 2) /* phy noise recorded by ucode right after tx */ #define M_PHY_NOISE (0x037 * 2) #define PHY_NOISE_MASK 0x00ff /* * Receive Frame Data Header for 802.11b DCF-only frames * * RxFrameSize: Actual byte length of the frame data received * PAD: padding (not used) * PhyRxStatus_0: PhyRxStatus 15:0 * PhyRxStatus_1: PhyRxStatus 31:16 * PhyRxStatus_2: PhyRxStatus 47:32 * PhyRxStatus_3: PhyRxStatus 63:48 * PhyRxStatus_4: PhyRxStatus 79:64 * PhyRxStatus_5: PhyRxStatus 95:80 * RxStatus1: MAC Rx Status * RxStatus2: extended MAC Rx status * RxTSFTime: RxTSFTime time of first MAC symbol + M_PHY_PLCPRX_DLY * RxChan: gain code, channel radio code, and phy type */ struct d11rxhdr_le { __le16 RxFrameSize; u16 PAD; __le16 PhyRxStatus_0; __le16 PhyRxStatus_1; __le16 PhyRxStatus_2; __le16 PhyRxStatus_3; __le16 PhyRxStatus_4; __le16 PhyRxStatus_5; __le16 RxStatus1; __le16 RxStatus2; __le16 RxTSFTime; __le16 RxChan; } __packed; struct d11rxhdr { u16 RxFrameSize; u16 PAD; u16 PhyRxStatus_0; u16 PhyRxStatus_1; u16 PhyRxStatus_2; u16 PhyRxStatus_3; u16 PhyRxStatus_4; u16 PhyRxStatus_5; u16 RxStatus1; u16 RxStatus2; u16 RxTSFTime; u16 RxChan; } __packed; /* PhyRxStatus_0: */ /* NPHY only: CCK, OFDM, preN, N */ #define PRXS0_FT_MASK 0x0003 /* NPHY only: clip count adjustment steps by AGC */ #define PRXS0_CLIP_MASK 0x000C #define PRXS0_CLIP_SHIFT 2 /* PHY received a frame with unsupported rate */ #define PRXS0_UNSRATE 0x0010 /* GPHY: rx ant, NPHY: upper sideband */ #define PRXS0_RXANT_UPSUBBAND 0x0020 /* CCK frame only: lost crs during cck frame reception */ #define PRXS0_LCRS 0x0040 /* Short Preamble */ #define PRXS0_SHORTH 0x0080 /* PLCP violation */ #define PRXS0_PLCPFV 0x0100 /* PLCP header integrity check failed */ #define PRXS0_PLCPHCF 0x0200 /* legacy PHY gain control */ #define PRXS0_GAIN_CTL 0x4000 /* NPHY: Antennas used for received frame, bitmask */ #define PRXS0_ANTSEL_MASK 0xF000 #define PRXS0_ANTSEL_SHIFT 0x12 /* subfield PRXS0_FT_MASK */ #define PRXS0_CCK 0x0000 /* valid only for G phy, use rxh->RxChan for A phy */ #define PRXS0_OFDM 0x0001 #define PRXS0_PREN 0x0002 #define PRXS0_STDN 0x0003 /* subfield PRXS0_ANTSEL_MASK */ #define PRXS0_ANTSEL_0 0x0 /* antenna 0 is used */ #define PRXS0_ANTSEL_1 0x2 /* antenna 1 is used */ #define PRXS0_ANTSEL_2 0x4 /* antenna 2 is used */ #define PRXS0_ANTSEL_3 0x8 /* antenna 3 is used */ /* PhyRxStatus_1: */ #define PRXS1_JSSI_MASK 0x00FF #define PRXS1_JSSI_SHIFT 0 #define PRXS1_SQ_MASK 0xFF00 #define PRXS1_SQ_SHIFT 8 /* nphy PhyRxStatus_1: */ #define PRXS1_nphy_PWR0_MASK 0x00FF #define PRXS1_nphy_PWR1_MASK 0xFF00 /* HTPHY Rx Status defines */ /* htphy PhyRxStatus_0: those bit are overlapped with PhyRxStatus_0 */ #define PRXS0_BAND 0x0400 /* 0 = 2.4G, 1 = 5G */ #define PRXS0_RSVD 0x0800 /* reserved; set to 0 */ #define PRXS0_UNUSED 0xF000 /* unused and not defined; set to 0 */ /* htphy PhyRxStatus_1: */ /* core enables for {3..0}, 0=disabled, 1=enabled */ #define PRXS1_HTPHY_CORE_MASK 0x000F /* antenna configation */ #define PRXS1_HTPHY_ANTCFG_MASK 0x00F0 /* Mixmode PLCP Length low byte mask */ #define PRXS1_HTPHY_MMPLCPLenL_MASK 0xFF00 /* htphy PhyRxStatus_2: */ /* Mixmode PLCP Length high byte maskw */ #define PRXS2_HTPHY_MMPLCPLenH_MASK 0x000F /* Mixmode PLCP rate mask */ #define PRXS2_HTPHY_MMPLCH_RATE_MASK 0x00F0 /* Rx power on core 0 */ #define PRXS2_HTPHY_RXPWR_ANT0 0xFF00 /* htphy PhyRxStatus_3: */ /* Rx power on core 1 */ #define PRXS3_HTPHY_RXPWR_ANT1 0x00FF /* Rx power on core 2 */ #define PRXS3_HTPHY_RXPWR_ANT2 0xFF00 /* htphy PhyRxStatus_4: */ /* Rx power on core 3 */ #define PRXS4_HTPHY_RXPWR_ANT3 0x00FF /* Coarse frequency offset */ #define PRXS4_HTPHY_CFO 0xFF00 /* htphy PhyRxStatus_5: */ /* Fine frequency offset */ #define PRXS5_HTPHY_FFO 0x00FF /* Advance Retard */ #define PRXS5_HTPHY_AR 0xFF00 #define HTPHY_MMPLCPLen(rxs) \ ((((rxs)->PhyRxStatus_1 & PRXS1_HTPHY_MMPLCPLenL_MASK) >> 8) | \ (((rxs)->PhyRxStatus_2 & PRXS2_HTPHY_MMPLCPLenH_MASK) << 8)) /* Get Rx power on core 0 */ #define HTPHY_RXPWR_ANT0(rxs) \ ((((rxs)->PhyRxStatus_2) & PRXS2_HTPHY_RXPWR_ANT0) >> 8) /* Get Rx power on core 1 */ #define HTPHY_RXPWR_ANT1(rxs) \ (((rxs)->PhyRxStatus_3) & PRXS3_HTPHY_RXPWR_ANT1) /* Get Rx power on core 2 */ #define HTPHY_RXPWR_ANT2(rxs) \ ((((rxs)->PhyRxStatus_3) & PRXS3_HTPHY_RXPWR_ANT2) >> 8) /* ucode RxStatus1: */ #define RXS_BCNSENT 0x8000 #define RXS_SECKINDX_MASK 0x07e0 #define RXS_SECKINDX_SHIFT 5 #define RXS_DECERR (1 << 4) #define RXS_DECATMPT (1 << 3) /* PAD bytes to make IP data 4 bytes aligned */ #define RXS_PBPRES (1 << 2) #define RXS_RESPFRAMETX (1 << 1) #define RXS_FCSERR (1 << 0) /* ucode RxStatus2: */ #define RXS_AMSDU_MASK 1 #define RXS_AGGTYPE_MASK 0x6 #define RXS_AGGTYPE_SHIFT 1 #define RXS_PHYRXST_VALID (1 << 8) #define RXS_RXANT_MASK 0x3 #define RXS_RXANT_SHIFT 12 /* RxChan */ #define RXS_CHAN_40 0x1000 #define RXS_CHAN_5G 0x0800 #define RXS_CHAN_ID_MASK 0x07f8 #define RXS_CHAN_ID_SHIFT 3 #define RXS_CHAN_PHYTYPE_MASK 0x0007 #define RXS_CHAN_PHYTYPE_SHIFT 0 /* Index of attenuations used during ucode power control. */ #define M_PWRIND_BLKS (0x184 * 2) #define M_PWRIND_MAP0 (M_PWRIND_BLKS + 0x0) #define M_PWRIND_MAP1 (M_PWRIND_BLKS + 0x2) #define M_PWRIND_MAP2 (M_PWRIND_BLKS + 0x4) #define M_PWRIND_MAP3 (M_PWRIND_BLKS + 0x6) /* M_PWRIND_MAP(core) macro */ #define M_PWRIND_MAP(core) (M_PWRIND_BLKS + ((core)<<1)) /* PSM SHM variable offsets */ #define M_PSM_SOFT_REGS 0x0 #define M_BOM_REV_MAJOR (M_PSM_SOFT_REGS + 0x0) #define M_BOM_REV_MINOR (M_PSM_SOFT_REGS + 0x2) #define M_UCODE_DBGST (M_PSM_SOFT_REGS + 0x40) /* ucode debug status code */ #define M_UCODE_MACSTAT (M_PSM_SOFT_REGS + 0xE0) /* macstat counters */ #define M_AGING_THRSH (0x3e * 2) /* max time waiting for medium before tx */ #define M_MBURST_SIZE (0x40 * 2) /* max frames in a frameburst */ #define M_MBURST_TXOP (0x41 * 2) /* max frameburst TXOP in unit of us */ #define M_SYNTHPU_DLY (0x4a * 2) /* pre-wakeup for synthpu, default: 500 */ #define M_PRETBTT (0x4b * 2) /* offset to the target txpwr */ #define M_ALT_TXPWR_IDX (M_PSM_SOFT_REGS + (0x3b * 2)) #define M_PHY_TX_FLT_PTR (M_PSM_SOFT_REGS + (0x3d * 2)) #define M_CTS_DURATION (M_PSM_SOFT_REGS + (0x5c * 2)) #define M_LP_RCCAL_OVR (M_PSM_SOFT_REGS + (0x6b * 2)) /* PKTENG Rx Stats Block */ #define M_RXSTATS_BLK_PTR (M_PSM_SOFT_REGS + (0x65 * 2)) /* ucode debug status codes */ /* not valid really */ #define DBGST_INACTIVE 0 /* after zeroing SHM, before suspending at init */ #define DBGST_INIT 1 /* "normal" state */ #define DBGST_ACTIVE 2 /* suspended */ #define DBGST_SUSPENDED 3 /* asleep (PS mode) */ #define DBGST_ASLEEP 4 /* Scratch Reg defs */ enum _ePsmScratchPadRegDefinitions { S_RSV0 = 0, S_RSV1, S_RSV2, /* offset 0x03: scratch registers for Dot11-contants */ S_DOT11_CWMIN, /* CW-minimum */ S_DOT11_CWMAX, /* CW-maximum */ S_DOT11_CWCUR, /* CW-current */ S_DOT11_SRC_LMT, /* short retry count limit */ S_DOT11_LRC_LMT, /* long retry count limit */ S_DOT11_DTIMCOUNT, /* DTIM-count */ /* offset 0x09: Tx-side scratch registers */ S_SEQ_NUM, /* hardware sequence number reg */ S_SEQ_NUM_FRAG, /* seq num for frags (at the start of MSDU) */ S_FRMRETX_CNT, /* frame retx count */ S_SSRC, /* Station short retry count */ S_SLRC, /* Station long retry count */ S_EXP_RSP, /* Expected response frame */ S_OLD_BREM, /* Remaining backoff ctr */ S_OLD_CWWIN, /* saved-off CW-cur */ S_TXECTL, /* TXE-Ctl word constructed in scr-pad */ S_CTXTST, /* frm type-subtype as read from Tx-descr */ /* offset 0x13: Rx-side scratch registers */ S_RXTST, /* Type and subtype in Rxframe */ /* Global state register */ S_STREG, /* state storage actual bit maps below */ S_TXPWR_SUM, /* Tx power control: accumulator */ S_TXPWR_ITER, /* Tx power control: iteration */ S_RX_FRMTYPE, /* Rate and PHY type for frames */ S_THIS_AGG, /* Size of this AGG (A-MSDU) */ S_KEYINDX, S_RXFRMLEN, /* Receive MPDU length in bytes */ /* offset 0x1B: Receive TSF time stored in SCR */ S_RXTSFTMRVAL_WD3, /* TSF value at the start of rx */ S_RXTSFTMRVAL_WD2, /* TSF value at the start of rx */ S_RXTSFTMRVAL_WD1, /* TSF value at the start of rx */ S_RXTSFTMRVAL_WD0, /* TSF value at the start of rx */ S_RXSSN, /* Received start seq number for A-MPDU BA */ S_RXQOSFLD, /* Rx-QoS field (if present) */ /* offset 0x21: Scratch pad regs used in microcode as temp storage */ S_TMP0, /* stmp0 */ S_TMP1, /* stmp1 */ S_TMP2, /* stmp2 */ S_TMP3, /* stmp3 */ S_TMP4, /* stmp4 */ S_TMP5, /* stmp5 */ S_PRQPENALTY_CTR, /* Probe response queue penalty counter */ S_ANTCNT, /* unsuccessful attempts on current ant. */ S_SYMBOL, /* flag for possible symbol ctl frames */ S_RXTP, /* rx frame type */ S_STREG2, /* extra state storage */ S_STREG3, /* even more extra state storage */ S_STREG4, /* ... */ S_STREG5, /* remember to initialize it to zero */ S_ADJPWR_IDX, S_CUR_PTR, /* Temp pointer for A-MPDU re-Tx SHM table */ S_REVID4, /* 0x33 */ S_INDX, /* 0x34 */ S_ADDR0, /* 0x35 */ S_ADDR1, /* 0x36 */ S_ADDR2, /* 0x37 */ S_ADDR3, /* 0x38 */ S_ADDR4, /* 0x39 */ S_ADDR5, /* 0x3A */ S_TMP6, /* 0x3B */ S_KEYINDX_BU, /* Backup for Key index */ S_MFGTEST_TMP0, /* Temp regs used for RX test calculations */ S_RXESN, /* Received end sequence number for A-MPDU BA */ S_STREG6, /* 0x3F */ }; #define S_BEACON_INDX S_OLD_BREM #define S_PRS_INDX S_OLD_CWWIN #define S_PHYTYPE S_SSRC #define S_PHYVER S_SLRC /* IHR SLOW_CTRL values */ #define SLOW_CTRL_PDE (1 << 0) #define SLOW_CTRL_FD (1 << 8) /* ucode mac statistic counters in shared memory */ struct macstat { u16 txallfrm; /* 0x80 */ u16 txrtsfrm; /* 0x82 */ u16 txctsfrm; /* 0x84 */ u16 txackfrm; /* 0x86 */ u16 txdnlfrm; /* 0x88 */ u16 txbcnfrm; /* 0x8a */ u16 txfunfl[8]; /* 0x8c - 0x9b */ u16 txtplunfl; /* 0x9c */ u16 txphyerr; /* 0x9e */ u16 pktengrxducast; /* 0xa0 */ u16 pktengrxdmcast; /* 0xa2 */ u16 rxfrmtoolong; /* 0xa4 */ u16 rxfrmtooshrt; /* 0xa6 */ u16 rxinvmachdr; /* 0xa8 */ u16 rxbadfcs; /* 0xaa */ u16 rxbadplcp; /* 0xac */ u16 rxcrsglitch; /* 0xae */ u16 rxstrt; /* 0xb0 */ u16 rxdfrmucastmbss; /* 0xb2 */ u16 rxmfrmucastmbss; /* 0xb4 */ u16 rxcfrmucast; /* 0xb6 */ u16 rxrtsucast; /* 0xb8 */ u16 rxctsucast; /* 0xba */ u16 rxackucast; /* 0xbc */ u16 rxdfrmocast; /* 0xbe */ u16 rxmfrmocast; /* 0xc0 */ u16 rxcfrmocast; /* 0xc2 */ u16 rxrtsocast; /* 0xc4 */ u16 rxctsocast; /* 0xc6 */ u16 rxdfrmmcast; /* 0xc8 */ u16 rxmfrmmcast; /* 0xca */ u16 rxcfrmmcast; /* 0xcc */ u16 rxbeaconmbss; /* 0xce */ u16 rxdfrmucastobss; /* 0xd0 */ u16 rxbeaconobss; /* 0xd2 */ u16 rxrsptmout; /* 0xd4 */ u16 bcntxcancl; /* 0xd6 */ u16 PAD; u16 rxf0ovfl; /* 0xda */ u16 rxf1ovfl; /* 0xdc */ u16 rxf2ovfl; /* 0xde */ u16 txsfovfl; /* 0xe0 */ u16 pmqovfl; /* 0xe2 */ u16 rxcgprqfrm; /* 0xe4 */ u16 rxcgprsqovfl; /* 0xe6 */ u16 txcgprsfail; /* 0xe8 */ u16 txcgprssuc; /* 0xea */ u16 prs_timeout; /* 0xec */ u16 rxnack; u16 frmscons; u16 txnack; u16 txglitch_nack; u16 txburst; /* 0xf6 # tx bursts */ u16 bphy_rxcrsglitch; /* bphy rx crs glitch */ u16 phywatchdog; /* 0xfa # of phy watchdog events */ u16 PAD; u16 bphy_badplcp; /* bphy bad plcp */ }; /* dot11 core-specific control flags */ #define SICF_PCLKE 0x0004 /* PHY clock enable */ #define SICF_PRST 0x0008 /* PHY reset */ #define SICF_MPCLKE 0x0010 /* MAC PHY clockcontrol enable */ #define SICF_FREF 0x0020 /* PLL FreqRefSelect */ /* NOTE: the following bw bits only apply when the core is attached * to a NPHY */ #define SICF_BWMASK 0x00c0 /* phy clock mask (b6 & b7) */ #define SICF_BW40 0x0080 /* 40MHz BW (160MHz phyclk) */ #define SICF_BW20 0x0040 /* 20MHz BW (80MHz phyclk) */ #define SICF_BW10 0x0000 /* 10MHz BW (40MHz phyclk) */ #define SICF_GMODE 0x2000 /* gmode enable */ /* dot11 core-specific status flags */ #define SISF_2G_PHY 0x0001 /* 2.4G capable phy */ #define SISF_5G_PHY 0x0002 /* 5G capable phy */ #define SISF_FCLKA 0x0004 /* FastClkAvailable */ #define SISF_DB_PHY 0x0008 /* Dualband phy */ /* === End of MAC reg, Beginning of PHY(b/a/g/n) reg === */ /* radio and LPPHY regs are separated */ #define BPHY_REG_OFT_BASE 0x0 /* offsets for indirect access to bphy registers */ #define BPHY_BB_CONFIG 0x01 #define BPHY_ADCBIAS 0x02 #define BPHY_ANACORE 0x03 #define BPHY_PHYCRSTH 0x06 #define BPHY_TEST 0x0a #define BPHY_PA_TX_TO 0x10 #define BPHY_SYNTH_DC_TO 0x11 #define BPHY_PA_TX_TIME_UP 0x12 #define BPHY_RX_FLTR_TIME_UP 0x13 #define BPHY_TX_POWER_OVERRIDE 0x14 #define BPHY_RF_OVERRIDE 0x15 #define BPHY_RF_TR_LOOKUP1 0x16 #define BPHY_RF_TR_LOOKUP2 0x17 #define BPHY_COEFFS 0x18 #define BPHY_PLL_OUT 0x19 #define BPHY_REFRESH_MAIN 0x1a #define BPHY_REFRESH_TO0 0x1b #define BPHY_REFRESH_TO1 0x1c #define BPHY_RSSI_TRESH 0x20 #define BPHY_IQ_TRESH_HH 0x21 #define BPHY_IQ_TRESH_H 0x22 #define BPHY_IQ_TRESH_L 0x23 #define BPHY_IQ_TRESH_LL 0x24 #define BPHY_GAIN 0x25 #define BPHY_LNA_GAIN_RANGE 0x26 #define BPHY_JSSI 0x27 #define BPHY_TSSI_CTL 0x28 #define BPHY_TSSI 0x29 #define BPHY_TR_LOSS_CTL 0x2a #define BPHY_LO_LEAKAGE 0x2b #define BPHY_LO_RSSI_ACC 0x2c #define BPHY_LO_IQMAG_ACC 0x2d #define BPHY_TX_DC_OFF1 0x2e #define BPHY_TX_DC_OFF2 0x2f #define BPHY_PEAK_CNT_THRESH 0x30 #define BPHY_FREQ_OFFSET 0x31 #define BPHY_DIVERSITY_CTL 0x32 #define BPHY_PEAK_ENERGY_LO 0x33 #define BPHY_PEAK_ENERGY_HI 0x34 #define BPHY_SYNC_CTL 0x35 #define BPHY_TX_PWR_CTRL 0x36 #define BPHY_TX_EST_PWR 0x37 #define BPHY_STEP 0x38 #define BPHY_WARMUP 0x39 #define BPHY_LMS_CFF_READ 0x3a #define BPHY_LMS_COEFF_I 0x3b #define BPHY_LMS_COEFF_Q 0x3c #define BPHY_SIG_POW 0x3d #define BPHY_RFDC_CANCEL_CTL 0x3e #define BPHY_HDR_TYPE 0x40 #define BPHY_SFD_TO 0x41 #define BPHY_SFD_CTL 0x42 #define BPHY_DEBUG 0x43 #define BPHY_RX_DELAY_COMP 0x44 #define BPHY_CRS_DROP_TO 0x45 #define BPHY_SHORT_SFD_NZEROS 0x46 #define BPHY_DSSS_COEFF1 0x48 #define BPHY_DSSS_COEFF2 0x49 #define BPHY_CCK_COEFF1 0x4a #define BPHY_CCK_COEFF2 0x4b #define BPHY_TR_CORR 0x4c #define BPHY_ANGLE_SCALE 0x4d #define BPHY_TX_PWR_BASE_IDX 0x4e #define BPHY_OPTIONAL_MODES2 0x4f #define BPHY_CCK_LMS_STEP 0x50 #define BPHY_BYPASS 0x51 #define BPHY_CCK_DELAY_LONG 0x52 #define BPHY_CCK_DELAY_SHORT 0x53 #define BPHY_PPROC_CHAN_DELAY 0x54 #define BPHY_DDFS_ENABLE 0x58 #define BPHY_PHASE_SCALE 0x59 #define BPHY_FREQ_CONTROL 0x5a #define BPHY_LNA_GAIN_RANGE_10 0x5b #define BPHY_LNA_GAIN_RANGE_32 0x5c #define BPHY_OPTIONAL_MODES 0x5d #define BPHY_RX_STATUS2 0x5e #define BPHY_RX_STATUS3 0x5f #define BPHY_DAC_CONTROL 0x60 #define BPHY_ANA11G_FILT_CTRL 0x62 #define BPHY_REFRESH_CTRL 0x64 #define BPHY_RF_OVERRIDE2 0x65 #define BPHY_SPUR_CANCEL_CTRL 0x66 #define BPHY_FINE_DIGIGAIN_CTRL 0x67 #define BPHY_RSSI_LUT 0x88 #define BPHY_RSSI_LUT_END 0xa7 #define BPHY_TSSI_LUT 0xa8 #define BPHY_TSSI_LUT_END 0xc7 #define BPHY_TSSI2PWR_LUT 0x380 #define BPHY_TSSI2PWR_LUT_END 0x39f #define BPHY_LOCOMP_LUT 0x3a0 #define BPHY_LOCOMP_LUT_END 0x3bf #define BPHY_TXGAIN_LUT 0x3c0 #define BPHY_TXGAIN_LUT_END 0x3ff /* Bits in BB_CONFIG: */ #define PHY_BBC_ANT_MASK 0x0180 #define PHY_BBC_ANT_SHIFT 7 #define BB_DARWIN 0x1000 #define BBCFG_RESETCCA 0x4000 #define BBCFG_RESETRX 0x8000 /* Bits in phytest(0x0a): */ #define TST_DDFS 0x2000 #define TST_TXFILT1 0x0800 #define TST_UNSCRAM 0x0400 #define TST_CARR_SUPP 0x0200 #define TST_DC_COMP_LOOP 0x0100 #define TST_LOOPBACK 0x0080 #define TST_TXFILT0 0x0040 #define TST_TXTEST_ENABLE 0x0020 #define TST_TXTEST_RATE 0x0018 #define TST_TXTEST_PHASE 0x0007 /* phytest txTestRate values */ #define TST_TXTEST_RATE_1MBPS 0 #define TST_TXTEST_RATE_2MBPS 1 #define TST_TXTEST_RATE_5_5MBPS 2 #define TST_TXTEST_RATE_11MBPS 3 #define TST_TXTEST_RATE_SHIFT 3 #define SHM_BYT_CNT 0x2 /* IHR location */ #define MAX_BYT_CNT 0x600 /* Maximum frame len */ struct d11cnt { u32 txfrag; u32 txmulti; u32 txfail; u32 txretry; u32 txretrie; u32 rxdup; u32 txrts; u32 txnocts; u32 txnoack; u32 rxfrag; u32 rxmulti; u32 rxcrc; u32 txfrmsnt; u32 rxundec; }; #endif /* _BRCM_D11_H_ */