/** * This file contains definitions of WLAN commands. */ #ifndef _LBS_HOST_H_ #define _LBS_HOST_H_ /** PUBLIC DEFINITIONS */ #define DEFAULT_AD_HOC_CHANNEL 6 #define DEFAULT_AD_HOC_CHANNEL_A 36 /** IEEE 802.11 oids */ #define OID_802_11_SSID 0x00008002 #define OID_802_11_INFRASTRUCTURE_MODE 0x00008008 #define OID_802_11_FRAGMENTATION_THRESHOLD 0x00008009 #define OID_802_11_RTS_THRESHOLD 0x0000800A #define OID_802_11_TX_ANTENNA_SELECTED 0x0000800D #define OID_802_11_SUPPORTED_RATES 0x0000800E #define OID_802_11_STATISTICS 0x00008012 #define OID_802_11_TX_RETRYCOUNT 0x0000801D #define OID_802_11D_ENABLE 0x00008020 #define CMD_OPTION_WAITFORRSP 0x0002 /** Host command IDs */ /* Return command are almost always the same as the host command, but with * bit 15 set high. There are a few exceptions, though... */ #define CMD_RET(cmd) (0x8000 | cmd) /* Return command convention exceptions: */ #define CMD_RET_802_11_ASSOCIATE 0x8012 /* Command codes */ #define CMD_CODE_DNLD 0x0002 #define CMD_GET_HW_SPEC 0x0003 #define CMD_EEPROM_UPDATE 0x0004 #define CMD_802_11_RESET 0x0005 #define CMD_802_11_SCAN 0x0006 #define CMD_802_11_GET_LOG 0x000b #define CMD_MAC_MULTICAST_ADR 0x0010 #define CMD_802_11_AUTHENTICATE 0x0011 #define CMD_802_11_EEPROM_ACCESS 0x0059 #define CMD_802_11_ASSOCIATE 0x0050 #define CMD_802_11_SET_WEP 0x0013 #define CMD_802_11_GET_STAT 0x0014 #define CMD_802_3_GET_STAT 0x0015 #define CMD_802_11_SNMP_MIB 0x0016 #define CMD_MAC_REG_MAP 0x0017 #define CMD_BBP_REG_MAP 0x0018 #define CMD_MAC_REG_ACCESS 0x0019 #define CMD_BBP_REG_ACCESS 0x001a #define CMD_RF_REG_ACCESS 0x001b #define CMD_802_11_RADIO_CONTROL 0x001c #define CMD_802_11_RF_CHANNEL 0x001d #define CMD_802_11_RF_TX_POWER 0x001e #define CMD_802_11_RSSI 0x001f #define CMD_802_11_RF_ANTENNA 0x0020 #define CMD_802_11_PS_MODE 0x0021 #define CMD_802_11_DATA_RATE 0x0022 #define CMD_RF_REG_MAP 0x0023 #define CMD_802_11_DEAUTHENTICATE 0x0024 #define CMD_802_11_REASSOCIATE 0x0025 #define CMD_802_11_DISASSOCIATE 0x0026 #define CMD_MAC_CONTROL 0x0028 #define CMD_802_11_AD_HOC_START 0x002b #define CMD_802_11_AD_HOC_JOIN 0x002c #define CMD_802_11_QUERY_TKIP_REPLY_CNTRS 0x002e #define CMD_802_11_ENABLE_RSN 0x002f #define CMD_802_11_PAIRWISE_TSC 0x0036 #define CMD_802_11_GROUP_TSC 0x0037 #define CMD_802_11_KEY_MATERIAL 0x005e #define CMD_802_11_SET_AFC 0x003c #define CMD_802_11_GET_AFC 0x003d #define CMD_802_11_AD_HOC_STOP 0x0040 #define CMD_802_11_BEACON_STOP 0x0049 #define CMD_802_11_MAC_ADDRESS 0x004D #define CMD_802_11_EEPROM_ACCESS 0x0059 #define CMD_802_11_BAND_CONFIG 0x0058 #define CMD_802_11D_DOMAIN_INFO 0x005b #define CMD_802_11_SLEEP_PARAMS 0x0066 #define CMD_802_11_INACTIVITY_TIMEOUT 0x0067 #define CMD_802_11_TPC_CFG 0x0072 #define CMD_802_11_PWR_CFG 0x0073 #define CMD_802_11_LED_GPIO_CTRL 0x004e #define CMD_802_11_SUBSCRIBE_EVENT 0x0075 #define CMD_802_11_RATE_ADAPT_RATESET 0x0076 #define CMD_802_11_TX_RATE_QUERY 0x007f #define CMD_GET_TSF 0x0080 #define CMD_BT_ACCESS 0x0087 #define CMD_FWT_ACCESS 0x0095 #define CMD_802_11_MONITOR_MODE 0x0098 #define CMD_MESH_ACCESS 0x009b #define CMD_SET_BOOT2_VER 0x00a5 /* For the IEEE Power Save */ #define CMD_SUBCMD_ENTER_PS 0x0030 #define CMD_SUBCMD_EXIT_PS 0x0031 #define CMD_SUBCMD_SLEEP_CONFIRMED 0x0034 #define CMD_SUBCMD_FULL_POWERDOWN 0x0035 #define CMD_SUBCMD_FULL_POWERUP 0x0036 #define CMD_ENABLE_RSN 0x0001 #define CMD_DISABLE_RSN 0x0000 #define CMD_ACT_SET 0x0001 #define CMD_ACT_GET 0x0000 #define CMD_ACT_GET_AES (CMD_ACT_GET + 2) #define CMD_ACT_SET_AES (CMD_ACT_SET + 2) #define CMD_ACT_REMOVE_AES (CMD_ACT_SET + 3) /* Define action or option for CMD_802_11_SET_WEP */ #define CMD_ACT_ADD 0x0002 #define CMD_ACT_REMOVE 0x0004 #define CMD_ACT_USE_DEFAULT 0x0008 #define CMD_TYPE_WEP_40_BIT 0x01 #define CMD_TYPE_WEP_104_BIT 0x02 #define CMD_NUM_OF_WEP_KEYS 4 #define CMD_WEP_KEY_INDEX_MASK 0x3fff /* Define action or option for CMD_802_11_RESET */ #define CMD_ACT_HALT 0x0003 /* Define action or option for CMD_802_11_SCAN */ #define CMD_BSS_TYPE_BSS 0x0001 #define CMD_BSS_TYPE_IBSS 0x0002 #define CMD_BSS_TYPE_ANY 0x0003 /* Define action or option for CMD_802_11_SCAN */ #define CMD_SCAN_TYPE_ACTIVE 0x0000 #define CMD_SCAN_TYPE_PASSIVE 0x0001 #define CMD_SCAN_RADIO_TYPE_BG 0 #define CMD_SCAN_PROBE_DELAY_TIME 0 /* Define action or option for CMD_MAC_CONTROL */ #define CMD_ACT_MAC_RX_ON 0x0001 #define CMD_ACT_MAC_TX_ON 0x0002 #define CMD_ACT_MAC_LOOPBACK_ON 0x0004 #define CMD_ACT_MAC_WEP_ENABLE 0x0008 #define CMD_ACT_MAC_INT_ENABLE 0x0010 #define CMD_ACT_MAC_MULTICAST_ENABLE 0x0020 #define CMD_ACT_MAC_BROADCAST_ENABLE 0x0040 #define CMD_ACT_MAC_PROMISCUOUS_ENABLE 0x0080 #define CMD_ACT_MAC_ALL_MULTICAST_ENABLE 0x0100 #define CMD_ACT_MAC_STRICT_PROTECTION_ENABLE 0x0400 /* Define action or option for CMD_802_11_RADIO_CONTROL */ #define CMD_TYPE_AUTO_PREAMBLE 0x0001 #define CMD_TYPE_SHORT_PREAMBLE 0x0002 #define CMD_TYPE_LONG_PREAMBLE 0x0003 #define TURN_ON_RF 0x01 #define RADIO_ON 0x01 #define RADIO_OFF 0x00 #define SET_AUTO_PREAMBLE 0x05 #define SET_SHORT_PREAMBLE 0x03 #define SET_LONG_PREAMBLE 0x01 /* Define action or option for CMD_802_11_RF_CHANNEL */ #define CMD_OPT_802_11_RF_CHANNEL_GET 0x00 #define CMD_OPT_802_11_RF_CHANNEL_SET 0x01 /* Define action or option for CMD_802_11_RF_TX_POWER */ #define CMD_ACT_TX_POWER_OPT_GET 0x0000 #define CMD_ACT_TX_POWER_OPT_SET_HIGH 0x8007 #define CMD_ACT_TX_POWER_OPT_SET_MID 0x8004 #define CMD_ACT_TX_POWER_OPT_SET_LOW 0x8000 #define CMD_ACT_TX_POWER_INDEX_HIGH 0x0007 #define CMD_ACT_TX_POWER_INDEX_MID 0x0004 #define CMD_ACT_TX_POWER_INDEX_LOW 0x0000 /* Define action or option for CMD_802_11_DATA_RATE */ #define CMD_ACT_SET_TX_AUTO 0x0000 #define CMD_ACT_SET_TX_FIX_RATE 0x0001 #define CMD_ACT_GET_TX_RATE 0x0002 #define CMD_ACT_SET_RX 0x0001 #define CMD_ACT_SET_TX 0x0002 #define CMD_ACT_SET_BOTH 0x0003 #define CMD_ACT_GET_RX 0x0004 #define CMD_ACT_GET_TX 0x0008 #define CMD_ACT_GET_BOTH 0x000c /* Define action or option for CMD_802_11_PS_MODE */ #define CMD_TYPE_CAM 0x0000 #define CMD_TYPE_MAX_PSP 0x0001 #define CMD_TYPE_FAST_PSP 0x0002 /* Define action or option for CMD_BT_ACCESS */ enum cmd_bt_access_opts { /* The bt commands start at 5 instead of 1 because the old dft commands * are mapped to 1-4. These old commands are no longer maintained and * should not be called. */ CMD_ACT_BT_ACCESS_ADD = 5, CMD_ACT_BT_ACCESS_DEL, CMD_ACT_BT_ACCESS_LIST, CMD_ACT_BT_ACCESS_RESET, CMD_ACT_BT_ACCESS_SET_INVERT, CMD_ACT_BT_ACCESS_GET_INVERT }; /* Define action or option for CMD_FWT_ACCESS */ enum cmd_fwt_access_opts { CMD_ACT_FWT_ACCESS_ADD = 1, CMD_ACT_FWT_ACCESS_DEL, CMD_ACT_FWT_ACCESS_LOOKUP, CMD_ACT_FWT_ACCESS_LIST, CMD_ACT_FWT_ACCESS_LIST_route, CMD_ACT_FWT_ACCESS_LIST_neighbor, CMD_ACT_FWT_ACCESS_RESET, CMD_ACT_FWT_ACCESS_CLEANUP, CMD_ACT_FWT_ACCESS_TIME, }; /* Define action or option for CMD_MESH_ACCESS */ enum cmd_mesh_access_opts { CMD_ACT_MESH_GET_TTL = 1, CMD_ACT_MESH_SET_TTL, CMD_ACT_MESH_GET_STATS, CMD_ACT_MESH_GET_ANYCAST, CMD_ACT_MESH_SET_ANYCAST, CMD_ACT_MESH_SET_LINK_COSTS, CMD_ACT_MESH_GET_LINK_COSTS, CMD_ACT_MESH_SET_BCAST_RATE, CMD_ACT_MESH_GET_BCAST_RATE, CMD_ACT_MESH_SET_RREQ_DELAY, CMD_ACT_MESH_GET_RREQ_DELAY, CMD_ACT_MESH_SET_ROUTE_EXP, CMD_ACT_MESH_GET_ROUTE_EXP, CMD_ACT_MESH_SET_AUTOSTART_ENABLED, CMD_ACT_MESH_GET_AUTOSTART_ENABLED, }; /** Card Event definition */ #define MACREG_INT_CODE_TX_PPA_FREE 0x00000000 #define MACREG_INT_CODE_TX_DMA_DONE 0x00000001 #define MACREG_INT_CODE_LINK_LOSE_W_SCAN 0x00000002 #define MACREG_INT_CODE_LINK_LOSE_NO_SCAN 0x00000003 #define MACREG_INT_CODE_LINK_SENSED 0x00000004 #define MACREG_INT_CODE_CMD_FINISHED 0x00000005 #define MACREG_INT_CODE_MIB_CHANGED 0x00000006 #define MACREG_INT_CODE_INIT_DONE 0x00000007 #define MACREG_INT_CODE_DEAUTHENTICATED 0x00000008 #define MACREG_INT_CODE_DISASSOCIATED 0x00000009 #define MACREG_INT_CODE_PS_AWAKE 0x0000000a #define MACREG_INT_CODE_PS_SLEEP 0x0000000b #define MACREG_INT_CODE_MIC_ERR_MULTICAST 0x0000000d #define MACREG_INT_CODE_MIC_ERR_UNICAST 0x0000000e #define MACREG_INT_CODE_WM_AWAKE 0x0000000f #define MACREG_INT_CODE_ADHOC_BCN_LOST 0x00000011 #define MACREG_INT_CODE_RSSI_LOW 0x00000019 #define MACREG_INT_CODE_SNR_LOW 0x0000001a #define MACREG_INT_CODE_MAX_FAIL 0x0000001b #define MACREG_INT_CODE_RSSI_HIGH 0x0000001c #define MACREG_INT_CODE_SNR_HIGH 0x0000001d #define MACREG_INT_CODE_MESH_AUTO_STARTED 0x00000023 #endif