#ifndef __LINUX_NL80211_H #define __LINUX_NL80211_H /* * 802.11 netlink interface public header * * Copyright 2006-2010 Johannes Berg * Copyright 2008 Michael Wu * Copyright 2008 Luis Carlos Cobo * Copyright 2008 Michael Buesch * Copyright 2008, 2009 Luis R. Rodriguez * Copyright 2008 Jouni Malinen * Copyright 2008 Colin McCabe * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above * copyright notice and this permission notice appear in all copies. * * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. * */ #include /** * DOC: Station handling * * Stations are added per interface, but a special case exists with VLAN * interfaces. When a station is bound to an AP interface, it may be moved * into a VLAN identified by a VLAN interface index (%NL80211_ATTR_STA_VLAN). * The station is still assumed to belong to the AP interface it was added * to. * * TODO: need more info? */ /** * DOC: Frame transmission/registration support * * Frame transmission and registration support exists to allow userspace * management entities such as wpa_supplicant react to management frames * that are not being handled by the kernel. This includes, for example, * certain classes of action frames that cannot be handled in the kernel * for various reasons. * * Frame registration is done on a per-interface basis and registrations * cannot be removed other than by closing the socket. It is possible to * specify a registration filter to register, for example, only for a * certain type of action frame. In particular with action frames, those * that userspace registers for will not be returned as unhandled by the * driver, so that the registered application has to take responsibility * for doing that. * * The type of frame that can be registered for is also dependent on the * driver and interface type. The frame types are advertised in wiphy * attributes so applications know what to expect. * * NOTE: When an interface changes type while registrations are active, * these registrations are ignored until the interface type is * changed again. This means that changing the interface type can * lead to a situation that couldn't otherwise be produced, but * any such registrations will be dormant in the sense that they * will not be serviced, i.e. they will not receive any frames. * * Frame transmission allows userspace to send for example the required * responses to action frames. It is subject to some sanity checking, * but many frames can be transmitted. When a frame was transmitted, its * status is indicated to the sending socket. * * For more technical details, see the corresponding command descriptions * below. */ /** * DOC: Virtual interface / concurrency capabilities * * Some devices are able to operate with virtual MACs, they can have * more than one virtual interface. The capability handling for this * is a bit complex though, as there may be a number of restrictions * on the types of concurrency that are supported. * * To start with, each device supports the interface types listed in * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the * types there no concurrency is implied. * * Once concurrency is desired, more attributes must be observed: * To start with, since some interface types are purely managed in * software, like the AP-VLAN type in mac80211 for example, there's * an additional list of these, they can be added at any time and * are only restricted by some semantic restrictions (e.g. AP-VLAN * cannot be added without a corresponding AP interface). This list * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute. * * Further, the list of supported combinations is exported. This is * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically, * it exports a list of "groups", and at any point in time the * interfaces that are currently active must fall into any one of * the advertised groups. Within each group, there are restrictions * on the number of interfaces of different types that are supported * and also the number of different channels, along with potentially * some other restrictions. See &enum nl80211_if_combination_attrs. * * All together, these attributes define the concurrency of virtual * interfaces that a given device supports. */ /** * enum nl80211_commands - supported nl80211 commands * * @NL80211_CMD_UNSPEC: unspecified command to catch errors * * @NL80211_CMD_GET_WIPHY: request information about a wiphy or dump request * to get a list of all present wiphys. * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or * %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME, * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ, * %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT, * %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD, * and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD. * However, for setting the channel, see %NL80211_CMD_SET_CHANNEL * instead, the support here is for backward compatibility only. * @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request * or rename notification. Has attributes %NL80211_ATTR_WIPHY and * %NL80211_ATTR_WIPHY_NAME. * @NL80211_CMD_DEL_WIPHY: Wiphy deleted. Has attributes * %NL80211_ATTR_WIPHY and %NL80211_ATTR_WIPHY_NAME. * * @NL80211_CMD_GET_INTERFACE: Request an interface's configuration; * either a dump request on a %NL80211_ATTR_WIPHY or a specific get * on an %NL80211_ATTR_IFINDEX is supported. * @NL80211_CMD_SET_INTERFACE: Set type of a virtual interface, requires * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_IFTYPE. * @NL80211_CMD_NEW_INTERFACE: Newly created virtual interface or response * to %NL80211_CMD_GET_INTERFACE. Has %NL80211_ATTR_IFINDEX, * %NL80211_ATTR_WIPHY and %NL80211_ATTR_IFTYPE attributes. Can also * be sent from userspace to request creation of a new virtual interface, * then requires attributes %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFTYPE and * %NL80211_ATTR_IFNAME. * @NL80211_CMD_DEL_INTERFACE: Virtual interface was deleted, has attributes * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_WIPHY. Can also be sent from * userspace to request deletion of a virtual interface, then requires * attribute %NL80211_ATTR_IFINDEX. * * @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified * by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC. * @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT, * %NL80211_ATTR_KEY_DEFAULT_MGMT, or %NL80211_ATTR_KEY_THRESHOLD. * @NL80211_CMD_NEW_KEY: add a key with given %NL80211_ATTR_KEY_DATA, * %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC, %NL80211_ATTR_KEY_CIPHER, * and %NL80211_ATTR_KEY_SEQ attributes. * @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX * or %NL80211_ATTR_MAC. * * @NL80211_CMD_GET_BEACON: retrieve beacon information (returned in a * %NL80222_CMD_NEW_BEACON message) * @NL80211_CMD_SET_BEACON: set the beacon on an access point interface * using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD, * %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes. * Following attributes are provided for drivers that generate full Beacon * and Probe Response frames internally: %NL80211_ATTR_SSID, * %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE, * %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS, * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY, * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_IE, %NL80211_ATTR_IE_PROBE_RESP, * %NL80211_ATTR_IE_ASSOC_RESP. * @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface, * parameters are like for %NL80211_CMD_SET_BEACON. * @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it * * @NL80211_CMD_GET_STATION: Get station attributes for station identified by * %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX. * @NL80211_CMD_SET_STATION: Set station attributes for station identified by * %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX. * @NL80211_CMD_NEW_STATION: Add a station with given attributes to the * the interface identified by %NL80211_ATTR_IFINDEX. * @NL80211_CMD_DEL_STATION: Remove a station identified by %NL80211_ATTR_MAC * or, if no MAC address given, all stations, on the interface identified * by %NL80211_ATTR_IFINDEX. * * @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to * destination %NL80211_ATTR_MAC on the interface identified by * %NL80211_ATTR_IFINDEX. * @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to * destination %NL80211_ATTR_MAC on the interface identified by * %NL80211_ATTR_IFINDEX. * @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by * %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP. * @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by * %NL80211_ATTR_MAC. * @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the * the interface identified by %NL80211_ATTR_IFINDEX. * @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC * or, if no MAC address given, all mesh paths, on the interface identified * by %NL80211_ATTR_IFINDEX. * @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by * %NL80211_ATTR_IFINDEX. * * @NL80211_CMD_GET_REG: ask the wireless core to send us its currently set * regulatory domain. * @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command * after being queried by the kernel. CRDA replies by sending a regulatory * domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our * current alpha2 if it found a match. It also provides * NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each * regulatory rule is a nested set of attributes given by * %NL80211_ATTR_REG_RULE_FREQ_[START|END] and * %NL80211_ATTR_FREQ_RANGE_MAX_BW with an attached power rule given by * %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and * %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP. * @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain * to the specified ISO/IEC 3166-1 alpha2 country code. The core will * store this as a valid request and then query userspace for it. * * @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the * interface identified by %NL80211_ATTR_IFINDEX * * @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the * interface identified by %NL80211_ATTR_IFINDEX * * @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The * interface is identified with %NL80211_ATTR_IFINDEX and the management * frame subtype with %NL80211_ATTR_MGMT_SUBTYPE. The extra IE data to be * added to the end of the specified management frame is specified with * %NL80211_ATTR_IE. If the command succeeds, the requested data will be * added to all specified management frames generated by * kernel/firmware/driver. * Note: This command has been removed and it is only reserved at this * point to avoid re-using existing command number. The functionality this * command was planned for has been provided with cleaner design with the * option to specify additional IEs in NL80211_CMD_TRIGGER_SCAN, * NL80211_CMD_AUTHENTICATE, NL80211_CMD_ASSOCIATE, * NL80211_CMD_DEAUTHENTICATE, and NL80211_CMD_DISASSOCIATE. * * @NL80211_CMD_GET_SCAN: get scan results * @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the * probe requests at CCK rate or not. * @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to * NL80211_CMD_GET_SCAN and on the "scan" multicast group) * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons, * partial scan results may be available * * @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain * intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL. * Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS) * are passed, they are used in the probe requests. For * broadcast, a broadcast SSID must be passed (ie. an empty * string). If no SSID is passed, no probe requests are sent and * a passive scan is performed. %NL80211_ATTR_SCAN_FREQUENCIES, * if passed, define which channels should be scanned; if not * passed, all channels allowed for the current regulatory domain * are used. Extra IEs can also be passed from the userspace by * using the %NL80211_ATTR_IE attribute. * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT * if scheduled scan is not running. * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan * results available. * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has * stopped. The driver may issue this event at any time during a * scheduled scan. One reason for stopping the scan is if the hardware * does not support starting an association or a normal scan while running * a scheduled scan. This event is also sent when the * %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface * is brought down while a scheduled scan was running. * * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation * or noise level * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to * NL80211_CMD_GET_SURVEY and on the "scan" multicast group) * * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain * has been changed and provides details of the request information * that caused the change such as who initiated the regulatory request * (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx * (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if * the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or * %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain * set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is * %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on * to (%NL80211_ATTR_REG_ALPHA2). * @NL80211_CMD_REG_BEACON_HINT: indicates to userspace that an AP beacon * has been found while world roaming thus enabling active scan or * any mode of operation that initiates TX (beacons) on a channel * where we would not have been able to do either before. As an example * if you are world roaming (regulatory domain set to world or if your * driver is using a custom world roaming regulatory domain) and while * doing a passive scan on the 5 GHz band you find an AP there (if not * on a DFS channel) you will now be able to actively scan for that AP * or use AP mode on your card on that same channel. Note that this will * never be used for channels 1-11 on the 2 GHz band as they are always * enabled world wide. This beacon hint is only sent if your device had * either disabled active scanning or beaconing on a channel. We send to * userspace the wiphy on which we removed a restriction from * (%NL80211_ATTR_WIPHY) and the channel on which this occurred * before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER) * the beacon hint was processed. * * @NL80211_CMD_AUTHENTICATE: authentication request and notification. * This command is used both as a command (request to authenticate) and * as an event on the "mlme" multicast group indicating completion of the * authentication process. * When used as a command, %NL80211_ATTR_IFINDEX is used to identify the * interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and * BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify * the SSID (mainly for association, but is included in authentication * request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used * to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE * is used to specify the authentication type. %NL80211_ATTR_IE is used to * define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs) * to be added to the frame. * When used as an event, this reports reception of an Authentication * frame in station and IBSS modes when the local MLME processed the * frame, i.e., it was for the local STA and was received in correct * state. This is similar to MLME-AUTHENTICATE.confirm primitive in the * MLME SAP interface (kernel providing MLME, userspace SME). The * included %NL80211_ATTR_FRAME attribute contains the management frame * (including both the header and frame body, but not FCS). This event is * also used to indicate if the authentication attempt timed out. In that * case the %NL80211_ATTR_FRAME attribute is replaced with a * %NL80211_ATTR_TIMED_OUT flag (and %NL80211_ATTR_MAC to indicate which * pending authentication timed out). * @NL80211_CMD_ASSOCIATE: association request and notification; like * NL80211_CMD_AUTHENTICATE but for Association and Reassociation * (similar to MLME-ASSOCIATE.request, MLME-REASSOCIATE.request, * MLME-ASSOCIATE.confirm or MLME-REASSOCIATE.confirm primitives). * @NL80211_CMD_DEAUTHENTICATE: deauthentication request and notification; like * NL80211_CMD_AUTHENTICATE but for Deauthentication frames (similar to * MLME-DEAUTHENTICATION.request and MLME-DEAUTHENTICATE.indication * primitives). * @NL80211_CMD_DISASSOCIATE: disassociation request and notification; like * NL80211_CMD_AUTHENTICATE but for Disassociation frames (similar to * MLME-DISASSOCIATE.request and MLME-DISASSOCIATE.indication primitives). * * @NL80211_CMD_MICHAEL_MIC_FAILURE: notification of a locally detected Michael * MIC (part of TKIP) failure; sent on the "mlme" multicast group; the * event includes %NL80211_ATTR_MAC to describe the source MAC address of * the frame with invalid MIC, %NL80211_ATTR_KEY_TYPE to show the key * type, %NL80211_ATTR_KEY_IDX to indicate the key identifier, and * %NL80211_ATTR_KEY_SEQ to indicate the TSC value of the frame; this * event matches with MLME-MICHAELMICFAILURE.indication() primitive * * @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a * FREQ attribute (for the initial frequency if no peer can be found) * and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those * should be fixed rather than automatically determined. Can only be * executed on a network interface that is UP, and fixed BSSID/FREQ * may be rejected. Another optional parameter is the beacon interval, * given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not * given defaults to 100 TU (102.4ms). * @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is * determined by the network interface. * * @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute * to identify the device, and the TESTDATA blob attribute to pass through * to the driver. * * @NL80211_CMD_CONNECT: connection request and notification; this command * requests to connect to a specified network but without separating * auth and assoc steps. For this, you need to specify the SSID in a * %NL80211_ATTR_SSID attribute, and can optionally specify the association * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC, * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT. * It is also sent as an event, with the BSSID and response IEs when the * connection is established or failed to be established. This can be * determined by the STATUS_CODE attribute. * @NL80211_CMD_ROAM: request that the card roam (currently not implemented), * sent as an event when the card/driver roamed by itself. * @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify * userspace that a connection was dropped by the AP or due to other * reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and * %NL80211_ATTR_REASON_CODE attributes are used. * * @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices * associated with this wiphy must be down and will follow. * * @NL80211_CMD_REMAIN_ON_CHANNEL: Request to remain awake on the specified * channel for the specified amount of time. This can be used to do * off-channel operations like transmit a Public Action frame and wait for * a response while being associated to an AP on another channel. * %NL80211_ATTR_IFINDEX is used to specify which interface (and thus * radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the * frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be * optionally used to specify additional channel parameters. * %NL80211_ATTR_DURATION is used to specify the duration in milliseconds * to remain on the channel. This command is also used as an event to * notify when the requested duration starts (it may take a while for the * driver to schedule this time due to other concurrent needs for the * radio). * When called, this operation returns a cookie (%NL80211_ATTR_COOKIE) * that will be included with any events pertaining to this request; * the cookie is also used to cancel the request. * @NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL: This command can be used to cancel a * pending remain-on-channel duration if the desired operation has been * completed prior to expiration of the originally requested duration. * %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify the * radio. The %NL80211_ATTR_COOKIE attribute must be given as well to * uniquely identify the request. * This command is also used as an event to notify when a requested * remain-on-channel duration has expired. * * @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX * rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface * and @NL80211_ATTR_TX_RATES the set of allowed rates. * * @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames * (via @NL80211_CMD_FRAME) for processing in userspace. This command * requires an interface index, a frame type attribute (optional for * backward compatibility reasons, if not given assumes action frames) * and a match attribute containing the first few bytes of the frame * that should match, e.g. a single byte for only a category match or * four bytes for vendor frames including the OUI. The registration * cannot be dropped, but is removed automatically when the netlink * socket is closed. Multiple registrations can be made. * @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for * backward compatibility * @NL80211_CMD_FRAME: Management frame TX request and RX notification. This * command is used both as a request to transmit a management frame and * as an event indicating reception of a frame that was not processed in * kernel code, but is for us (i.e., which may need to be processed in a * user space application). %NL80211_ATTR_FRAME is used to specify the * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and * optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on * which channel the frame is to be transmitted or was received. If this * channel is not the current channel (remain-on-channel or the * operational channel) the device will switch to the given channel and * transmit the frame, optionally waiting for a response for the time * specified using %NL80211_ATTR_DURATION. When called, this operation * returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the * TX status event pertaining to the TX request. * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the * management frames at CCK rate or not in 2GHz band. * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this * command may be used with the corresponding cookie to cancel the wait * time if it is known that it is no longer necessary. * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility. * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame * transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies * the TX command and %NL80211_ATTR_FRAME includes the contents of the * frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged * the frame. * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for * backward compatibility. * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command * is used to configure connection quality monitoring notification trigger * levels. * @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This * command is used as an event to indicate the that a trigger level was * reached. * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ * and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed * by %NL80211_ATTR_IFINDEX) shall operate on. * In case multiple channels are supported by the device, the mechanism * with which it switches channels is implementation-defined. * When a monitor interface is given, it can only switch channel while * no other interfaces are operating to avoid disturbing the operation * of any other interfaces, and other interfaces will again take * precedence when they are used. * * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. * * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial * mesh config parameters may be given. * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the * network is determined by the network interface. * * @NL80211_CMD_UNPROT_DEAUTHENTICATE: Unprotected deauthentication frame * notification. This event is used to indicate that an unprotected * deauthentication frame was dropped when MFP is in use. * @NL80211_CMD_UNPROT_DISASSOCIATE: Unprotected disassociation frame * notification. This event is used to indicate that an unprotected * disassociation frame was dropped when MFP is in use. * * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a * beacon or probe response from a compatible mesh peer. This is only * sent while no station information (sta_info) exists for the new peer * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set. On * reception of this notification, userspace may decide to create a new * station (@NL80211_CMD_NEW_STATION). To stop this notification from * reoccurring, the userspace authentication daemon may want to create the * new station with the AUTHENTICATED flag unset and maybe change it later * depending on the authentication result. * * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings. * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings. * Since wireless is more complex than wired ethernet, it supports * various triggers. These triggers can be configured through this * command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For * more background information, see * http://wireless.kernel.org/en/users/Documentation/WoWLAN. * * @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver * the necessary information for supporting GTK rekey offload. This * feature is typically used during WoWLAN. The configuration data * is contained in %NL80211_ATTR_REKEY_DATA (which is nested and * contains the data in sub-attributes). After rekeying happened, * this command may also be sent by the driver as an MLME event to * inform userspace of the new replay counter. * * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace * of PMKSA caching dandidates. * * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup). * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ enum nl80211_commands { /* don't change the order or add anything between, this is ABI! */ NL80211_CMD_UNSPEC, NL80211_CMD_GET_WIPHY, /* can dump */ NL80211_CMD_SET_WIPHY, NL80211_CMD_NEW_WIPHY, NL80211_CMD_DEL_WIPHY, NL80211_CMD_GET_INTERFACE, /* can dump */ NL80211_CMD_SET_INTERFACE, NL80211_CMD_NEW_INTERFACE, NL80211_CMD_DEL_INTERFACE, NL80211_CMD_GET_KEY, NL80211_CMD_SET_KEY, NL80211_CMD_NEW_KEY, NL80211_CMD_DEL_KEY, NL80211_CMD_GET_BEACON, NL80211_CMD_SET_BEACON, NL80211_CMD_NEW_BEACON, NL80211_CMD_DEL_BEACON, NL80211_CMD_GET_STATION, NL80211_CMD_SET_STATION, NL80211_CMD_NEW_STATION, NL80211_CMD_DEL_STATION, NL80211_CMD_GET_MPATH, NL80211_CMD_SET_MPATH, NL80211_CMD_NEW_MPATH, NL80211_CMD_DEL_MPATH, NL80211_CMD_SET_BSS, NL80211_CMD_SET_REG, NL80211_CMD_REQ_SET_REG, NL80211_CMD_GET_MESH_CONFIG, NL80211_CMD_SET_MESH_CONFIG, NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */, NL80211_CMD_GET_REG, NL80211_CMD_GET_SCAN, NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_NEW_SCAN_RESULTS, NL80211_CMD_SCAN_ABORTED, NL80211_CMD_REG_CHANGE, NL80211_CMD_AUTHENTICATE, NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, NL80211_CMD_DISASSOCIATE, NL80211_CMD_MICHAEL_MIC_FAILURE, NL80211_CMD_REG_BEACON_HINT, NL80211_CMD_JOIN_IBSS, NL80211_CMD_LEAVE_IBSS, NL80211_CMD_TESTMODE, NL80211_CMD_CONNECT, NL80211_CMD_ROAM, NL80211_CMD_DISCONNECT, NL80211_CMD_SET_WIPHY_NETNS, NL80211_CMD_GET_SURVEY, NL80211_CMD_NEW_SURVEY_RESULTS, NL80211_CMD_SET_PMKSA, NL80211_CMD_DEL_PMKSA, NL80211_CMD_FLUSH_PMKSA, NL80211_CMD_REMAIN_ON_CHANNEL, NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL, NL80211_CMD_SET_TX_BITRATE_MASK, NL80211_CMD_REGISTER_FRAME, NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME, NL80211_CMD_FRAME, NL80211_CMD_ACTION = NL80211_CMD_FRAME, NL80211_CMD_FRAME_TX_STATUS, NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS, NL80211_CMD_SET_POWER_SAVE, NL80211_CMD_GET_POWER_SAVE, NL80211_CMD_SET_CQM, NL80211_CMD_NOTIFY_CQM, NL80211_CMD_SET_CHANNEL, NL80211_CMD_SET_WDS_PEER, NL80211_CMD_FRAME_WAIT_CANCEL, NL80211_CMD_JOIN_MESH, NL80211_CMD_LEAVE_MESH, NL80211_CMD_UNPROT_DEAUTHENTICATE, NL80211_CMD_UNPROT_DISASSOCIATE, NL80211_CMD_NEW_PEER_CANDIDATE, NL80211_CMD_GET_WOWLAN, NL80211_CMD_SET_WOWLAN, NL80211_CMD_START_SCHED_SCAN, NL80211_CMD_STOP_SCHED_SCAN, NL80211_CMD_SCHED_SCAN_RESULTS, NL80211_CMD_SCHED_SCAN_STOPPED, NL80211_CMD_SET_REKEY_OFFLOAD, NL80211_CMD_PMKSA_CANDIDATE, NL80211_CMD_TDLS_OPER, NL80211_CMD_TDLS_MGMT, /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ __NL80211_CMD_AFTER_LAST, NL80211_CMD_MAX = __NL80211_CMD_AFTER_LAST - 1 }; /* * Allow user space programs to use #ifdef on new commands by defining them * here */ #define NL80211_CMD_SET_BSS NL80211_CMD_SET_BSS #define NL80211_CMD_SET_MGMT_EXTRA_IE NL80211_CMD_SET_MGMT_EXTRA_IE #define NL80211_CMD_REG_CHANGE NL80211_CMD_REG_CHANGE #define NL80211_CMD_AUTHENTICATE NL80211_CMD_AUTHENTICATE #define NL80211_CMD_ASSOCIATE NL80211_CMD_ASSOCIATE #define NL80211_CMD_DEAUTHENTICATE NL80211_CMD_DEAUTHENTICATE #define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE #define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT /* source-level API compatibility */ #define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG #define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG #define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE /** * enum nl80211_attrs - nl80211 netlink attributes * * @NL80211_ATTR_UNSPEC: unspecified attribute to catch errors * * @NL80211_ATTR_WIPHY: index of wiphy to operate on, cf. * /sys/class/ieee80211//index * @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming) * @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz * @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ * if HT20 or HT40 are allowed (i.e., 802.11n disabled if not included): * NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including * this attribute) * NL80211_CHAN_HT20 = HT20 only * NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel * NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel * @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is * less than or equal to the RTS threshold; allowed range: 1..255; * dot11ShortRetryLimit; u8 * @NL80211_ATTR_WIPHY_RETRY_LONG: TX retry limit for frames whose length is * greater than the RTS threshold; allowed range: 1..255; * dot11ShortLongLimit; u8 * @NL80211_ATTR_WIPHY_FRAG_THRESHOLD: fragmentation threshold, i.e., maximum * length in octets for frames; allowed range: 256..8000, disable * fragmentation with (u32)-1; dot11FragmentationThreshold; u32 * @NL80211_ATTR_WIPHY_RTS_THRESHOLD: RTS threshold (TX frames with length * larger than or equal to this use RTS/CTS handshake); allowed range: * 0..65536, disable with (u32)-1; dot11RTSThreshold; u32 * @NL80211_ATTR_WIPHY_COVERAGE_CLASS: Coverage Class as defined by IEEE 802.11 * section 7.3.2.9; dot11CoverageClass; u8 * * @NL80211_ATTR_IFINDEX: network interface index of the device to operate on * @NL80211_ATTR_IFNAME: network interface name * @NL80211_ATTR_IFTYPE: type of virtual interface, see &enum nl80211_iftype * * @NL80211_ATTR_MAC: MAC address (various uses) * * @NL80211_ATTR_KEY_DATA: (temporal) key data; for TKIP this consists of * 16 bytes encryption key followed by 8 bytes each for TX and RX MIC * keys * @NL80211_ATTR_KEY_IDX: key ID (u8, 0-3) * @NL80211_ATTR_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11 * section 7.3.2.25.1, e.g. 0x000FAC04) * @NL80211_ATTR_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and * CCMP keys, each six bytes in little endian * * @NL80211_ATTR_BEACON_INTERVAL: beacon interval in TU * @NL80211_ATTR_DTIM_PERIOD: DTIM period for beaconing * @NL80211_ATTR_BEACON_HEAD: portion of the beacon before the TIM IE * @NL80211_ATTR_BEACON_TAIL: portion of the beacon after the TIM IE * * @NL80211_ATTR_STA_AID: Association ID for the station (u16) * @NL80211_ATTR_STA_FLAGS: flags, nested element with NLA_FLAG attributes of * &enum nl80211_sta_flags (deprecated, use %NL80211_ATTR_STA_FLAGS2) * @NL80211_ATTR_STA_LISTEN_INTERVAL: listen interval as defined by * IEEE 802.11 7.3.1.6 (u16). * @NL80211_ATTR_STA_SUPPORTED_RATES: supported rates, array of supported * rates as defined by IEEE 802.11 7.3.2.2 but without the length * restriction (at most %NL80211_MAX_SUPP_RATES). * @NL80211_ATTR_STA_VLAN: interface index of VLAN interface to move station * to, or the AP interface the station was originally added to to. * @NL80211_ATTR_STA_INFO: information about a station, part of station info * given for %NL80211_CMD_GET_STATION, nested attribute containing * info as possible, see &enum nl80211_sta_info. * * @NL80211_ATTR_WIPHY_BANDS: Information about an operating bands, * consisting of a nested array. * * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes). * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link. * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path. * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path * info given for %NL80211_CMD_GET_MPATH, nested attribute described at * &enum nl80211_mpath_info. * * @NL80211_ATTR_MNTR_FLAGS: flags, nested element with NLA_FLAG attributes of * &enum nl80211_mntr_flags. * * @NL80211_ATTR_REG_ALPHA2: an ISO-3166-alpha2 country code for which the * current regulatory domain should be set to or is already set to. * For example, 'CR', for Costa Rica. This attribute is used by the kernel * to query the CRDA to retrieve one regulatory domain. This attribute can * also be used by userspace to query the kernel for the currently set * regulatory domain. We chose an alpha2 as that is also used by the * IEEE-802.11d country information element to identify a country. * Users can also simply ask the wireless core to set regulatory domain * to a specific alpha2. * @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory * rules. * * @NL80211_ATTR_BSS_CTS_PROT: whether CTS protection is enabled (u8, 0 or 1) * @NL80211_ATTR_BSS_SHORT_PREAMBLE: whether short preamble is enabled * (u8, 0 or 1) * @NL80211_ATTR_BSS_SHORT_SLOT_TIME: whether short slot time enabled * (u8, 0 or 1) * @NL80211_ATTR_BSS_BASIC_RATES: basic rates, array of basic * rates in format defined by IEEE 802.11 7.3.2.2 but without the length * restriction (at most %NL80211_MAX_SUPP_RATES). * * @NL80211_ATTR_HT_CAPABILITY: HT Capability information element (from * association request when used with NL80211_CMD_NEW_STATION) * * @NL80211_ATTR_SUPPORTED_IFTYPES: nested attribute containing all * supported interface types, each a flag attribute with the number * of the interface mode. * * @NL80211_ATTR_MGMT_SUBTYPE: Management frame subtype for * %NL80211_CMD_SET_MGMT_EXTRA_IE. * * @NL80211_ATTR_IE: Information element(s) data (used, e.g., with * %NL80211_CMD_SET_MGMT_EXTRA_IE). * * @NL80211_ATTR_MAX_NUM_SCAN_SSIDS: number of SSIDs you can scan with * a single scan request, a wiphy attribute. * @NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS: number of SSIDs you can * scan with a single scheduled scan request, a wiphy attribute. * @NL80211_ATTR_MAX_SCAN_IE_LEN: maximum length of information elements * that can be added to a scan request * @NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN: maximum length of information * elements that can be added to a scheduled scan request * @NL80211_ATTR_MAX_MATCH_SETS: maximum number of sets that can be * used with @NL80211_ATTR_SCHED_SCAN_MATCH, a wiphy attribute. * * @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz) * @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive * scanning and include a zero-length SSID (wildcard) for wildcard scan * @NL80211_ATTR_BSS: scan result BSS * * @NL80211_ATTR_REG_INITIATOR: indicates who requested the regulatory domain * currently in effect. This could be any of the %NL80211_REGDOM_SET_BY_* * @NL80211_ATTR_REG_TYPE: indicates the type of the regulatory domain currently * set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*) * * @NL80211_ATTR_SUPPORTED_COMMANDS: wiphy attribute that specifies * an array of command numbers (i.e. a mapping index to command number) * that the driver for the given wiphy supports. * * @NL80211_ATTR_FRAME: frame data (binary attribute), including frame header * and body, but not FCS; used, e.g., with NL80211_CMD_AUTHENTICATE and * NL80211_CMD_ASSOCIATE events * @NL80211_ATTR_SSID: SSID (binary attribute, 0..32 octets) * @NL80211_ATTR_AUTH_TYPE: AuthenticationType, see &enum nl80211_auth_type, * represented as a u32 * @NL80211_ATTR_REASON_CODE: ReasonCode for %NL80211_CMD_DEAUTHENTICATE and * %NL80211_CMD_DISASSOCIATE, u16 * * @NL80211_ATTR_KEY_TYPE: Key Type, see &enum nl80211_key_type, represented as * a u32 * * @NL80211_ATTR_FREQ_BEFORE: A channel which has suffered a regulatory change * due to considerations from a beacon hint. This attribute reflects * the state of the channel _before_ the beacon hint processing. This * attributes consists of a nested attribute containing * NL80211_FREQUENCY_ATTR_* * @NL80211_ATTR_FREQ_AFTER: A channel which has suffered a regulatory change * due to considerations from a beacon hint. This attribute reflects * the state of the channel _after_ the beacon hint processing. This * attributes consists of a nested attribute containing * NL80211_FREQUENCY_ATTR_* * * @NL80211_ATTR_CIPHER_SUITES: a set of u32 values indicating the supported * cipher suites * * @NL80211_ATTR_FREQ_FIXED: a flag indicating the IBSS should not try to look * for other networks on different channels * * @NL80211_ATTR_TIMED_OUT: a flag indicating than an operation timed out; this * is used, e.g., with %NL80211_CMD_AUTHENTICATE event * * @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is * used for the association (&enum nl80211_mfp, represented as a u32); * this attribute can be used * with %NL80211_CMD_ASSOCIATE request * * @NL80211_ATTR_STA_FLAGS2: Attribute containing a * &struct nl80211_sta_flag_update. * * @NL80211_ATTR_CONTROL_PORT: A flag indicating whether user space controls * IEEE 802.1X port, i.e., sets/clears %NL80211_STA_FLAG_AUTHORIZED, in * station mode. If the flag is included in %NL80211_CMD_ASSOCIATE * request, the driver will assume that the port is unauthorized until * authorized by user space. Otherwise, port is marked authorized by * default in station mode. * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the * ethertype that will be used for key negotiation. It can be * specified with the associate and connect commands. If it is not * specified, the value defaults to 0x888E (PAE, 802.1X). This * attribute is also used as a flag in the wiphy information to * indicate that protocols other than PAE are supported. * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom * ethertype frames used for key negotiation must not be encrypted. * * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver. * We recommend using nested, driver-specific attributes within this. * * @NL80211_ATTR_DISCONNECTED_BY_AP: A flag indicating that the DISCONNECT * event was due to the AP disconnecting the station, and not due to * a local disconnect request. * @NL80211_ATTR_STATUS_CODE: StatusCode for the %NL80211_CMD_CONNECT * event (u16) * @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating * that protected APs should be used. This is also used with NEW_BEACON to * indicate that the BSS is to use protection. * * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT, ASSOCIATE, and NEW_BEACON * to indicate which unicast key ciphers will be used with the connection * (an array of u32). * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT, ASSOCIATE, and NEW_BEACON to * indicate which group key cipher will be used with the connection (a * u32). * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT, ASSOCIATE, and NEW_BEACON to * indicate which WPA version(s) the AP we want to associate with is using * (a u32 with flags from &enum nl80211_wpa_versions). * @NL80211_ATTR_AKM_SUITES: Used with CONNECT, ASSOCIATE, and NEW_BEACON to * indicate which key management algorithm(s) to use (an array of u32). * * @NL80211_ATTR_REQ_IE: (Re)association request information elements as * sent out by the card, for ROAM and successful CONNECT events. * @NL80211_ATTR_RESP_IE: (Re)association response information elements as * sent by peer, for ROAM and successful CONNECT events. * * @NL80211_ATTR_PREV_BSSID: previous BSSID, to be used by in ASSOCIATE * commands to specify using a reassociate frame * * @NL80211_ATTR_KEY: key information in a nested attribute with * %NL80211_KEY_* sub-attributes * @NL80211_ATTR_KEYS: array of keys for static WEP keys for connect() * and join_ibss(), key information is in a nested attribute each * with %NL80211_KEY_* sub-attributes * * @NL80211_ATTR_PID: Process ID of a network namespace. * * @NL80211_ATTR_GENERATION: Used to indicate consistent snapshots for * dumps. This number increases whenever the object list being * dumped changes, and as such userspace can verify that it has * obtained a complete and consistent snapshot by verifying that * all dump messages contain the same generation number. If it * changed then the list changed and the dump should be repeated * completely from scratch. * * @NL80211_ATTR_4ADDR: Use 4-address frames on a virtual interface * * @NL80211_ATTR_SURVEY_INFO: survey information about a channel, part of * the survey response for %NL80211_CMD_GET_SURVEY, nested attribute * containing info as possible, see &enum survey_info. * * @NL80211_ATTR_PMKID: PMK material for PMKSA caching. * @NL80211_ATTR_MAX_NUM_PMKIDS: maximum number of PMKIDs a firmware can * cache, a wiphy attribute. * * @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32. * @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that * specifies the maximum duration that can be requested with the * remain-on-channel operation, in milliseconds, u32. * * @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects. * * @NL80211_ATTR_TX_RATES: Nested set of attributes * (enum nl80211_tx_rate_attributes) describing TX rates per band. The * enum nl80211_band value is used as the index (nla_type() of the nested * data. If a band is not included, it will be configured to allow all * rates based on negotiated supported rates information. This attribute * is used with %NL80211_CMD_SET_TX_BITRATE_MASK. * * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain * at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME. * @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the * @NL80211_CMD_REGISTER_FRAME command. * @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing * information about which frame types can be transmitted with * %NL80211_CMD_FRAME. * @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing * information about which frame types can be registered for RX. * * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was * acknowledged by the recipient. * * @NL80211_ATTR_CQM: connection quality monitor configuration in a * nested attribute with %NL80211_ATTR_CQM_* sub-attributes. * * @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command * is requesting a local authentication/association state change without * invoking actual management frame exchange. This can be used with * NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE, * NL80211_CMD_DISASSOCIATE. * * @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations * connected to this BSS. * * @NL80211_ATTR_WIPHY_TX_POWER_SETTING: Transmit power setting type. See * &enum nl80211_tx_power_setting for possible values. * @NL80211_ATTR_WIPHY_TX_POWER_LEVEL: Transmit power level in signed mBm units. * This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING * for non-automatic settings. * * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly * means support for per-station GTKs. * * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting. * This can be used to mask out antennas which are not attached or should * not be used for transmitting. If an antenna is not selected in this * bitmap the hardware is not allowed to transmit on this antenna. * * Each bit represents one antenna, starting with antenna 1 at the first * bit. Depending on which antennas are selected in the bitmap, 802.11n * drivers can derive which chainmasks to use (if all antennas belonging to * a particular chain are disabled this chain should be disabled) and if * a chain has diversity antennas wether diversity should be used or not. * HT capabilities (STBC, TX Beamforming, Antenna selection) can be * derived from the available chains after applying the antenna mask. * Non-802.11n drivers can derive wether to use diversity or not. * Drivers may reject configurations or RX/TX mask combinations they cannot * support by returning -EINVAL. * * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving. * This can be used to mask out antennas which are not attached or should * not be used for receiving. If an antenna is not selected in this bitmap * the hardware should not be configured to receive on this antenna. * For a more detailed description see @NL80211_ATTR_WIPHY_ANTENNA_TX. * * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX: Bitmap of antennas which are available * for configuration as TX antennas via the above parameters. * * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX: Bitmap of antennas which are available * for configuration as RX antennas via the above parameters. * * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS * * @NL80211_ATTR_OFFCHANNEL_TX_OK: For management frame TX, the frame may be * transmitted on another channel when the channel given doesn't match * the current channel. If the current channel doesn't match and this * flag isn't set, the frame will be rejected. This is also used as an * nl80211 capability flag. * * @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16) * * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags * attributes, specifying what a key should be set as default as. * See &enum nl80211_key_default_types. * * @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters. These cannot be * changed once the mesh is active. * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute * containing attributes from &enum nl80211_meshconf_params. * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver * allows auth frames in a mesh to be passed to userspace for processing via * the @NL80211_MESH_SETUP_USERSPACE_AUTH flag. * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as * defined in &enum nl80211_plink_state. Used when userspace is * driving the peer link management state machine. * @NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled. * * @NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED: indicates, as part of the wiphy * capabilities, the supported WoWLAN triggers * @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to * indicate which WoW triggers should be enabled. This is also * used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN * triggers. * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan * cycles, in msecs. * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more * sets of attributes to match during scheduled scans. Only BSSs * that match any of the sets will be reported. These are * pass-thru filter rules. * For a match to succeed, the BSS must match all attributes of a * set. Since not every hardware supports matching all types of * attributes, there is no guarantee that the reported BSSs are * fully complying with the match sets and userspace needs to be * able to ignore them by itself. * Thus, the implementation is somewhat hardware-dependent, but * this is only an optimization and the userspace application * needs to handle all the non-filtered results anyway. * If the match attributes don't make sense when combined with * the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID * is included in the probe request, but the match attributes * will never let it go through), -EINVAL may be returned. * If ommited, no filtering is done. * * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported * interface combinations. In each nested item, it contains attributes * defined in &enum nl80211_if_combination_attrs. * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like * %NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that * are managed in software: interfaces of these types aren't subject to * any restrictions in their number or combinations. * * @%NL80211_ATTR_REKEY_DATA: nested attribute containing the information * necessary for GTK rekeying in the device, see &enum nl80211_rekey_data. * * @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan, * nested array attribute containing an entry for each band, with the entry * being a list of supported rates as defined by IEEE 802.11 7.3.2.2 but * without the length restriction (at most %NL80211_MAX_SUPP_RATES). * * @NL80211_ATTR_HIDDEN_SSID: indicates whether SSID is to be hidden from Beacon * and Probe Response (when response to wildcard Probe Request); see * &enum nl80211_hidden_ssid, represented as a u32 * * @NL80211_ATTR_IE_PROBE_RESP: Information element(s) for Probe Response frame. * This is used with %NL80211_CMD_NEW_BEACON and %NL80211_CMD_SET_BEACON to * provide extra IEs (e.g., WPS/P2P IE) into Probe Response frames when the * driver (or firmware) replies to Probe Request frames. * @NL80211_ATTR_IE_ASSOC_RESP: Information element(s) for (Re)Association * Response frames. This is used with %NL80211_CMD_NEW_BEACON and * %NL80211_CMD_SET_BEACON to provide extra IEs (e.g., WPS/P2P IE) into * (Re)Association Response frames when the driver (or firmware) replies to * (Re)Association Request frames. * * @NL80211_ATTR_STA_WME: Nested attribute containing the wme configuration * of the station, see &enum nl80211_sta_wme_attr. * @NL80211_ATTR_SUPPORT_AP_UAPSD: the device supports uapsd when working * as AP. * * @NL80211_ATTR_ROAM_SUPPORT: Indicates whether the firmware is capable of * roaming to another AP in the same ESS if the signal lever is low. * * @NL80211_ATTR_PMKSA_CANDIDATE: Nested attribute containing the PMKSA caching * candidate information, see &enum nl80211_pmksa_candidate_attr. * * @NL80211_ATTR_TX_NO_CCK_RATE: Indicates whether to use CCK rate or not * for management frames transmission. In order to avoid p2p probe/action * frames are being transmitted at CCK rate in 2GHz band, the user space * applications use this attribute. * This attribute is used with %NL80211_CMD_TRIGGER_SCAN and * %NL80211_CMD_FRAME commands. * * @NL80211_ATTR_TDLS_ACTION: Low level TDLS action code (e.g. link setup * request, link setup confirm, link teardown, etc.). Values are * described in the TDLS (802.11z) specification. * @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a * TDLS conversation between two devices. * @NL80211_ATTR_TDLS_OPERATION: High level TDLS operation; see * &enum nl80211_tdls_operation, represented as a u8. * @NL80211_ATTR_TDLS_SUPPORT: A flag indicating the device can operate * as a TDLS peer sta. * @NL80211_ATTR_TDLS_EXTERNAL_SETUP: The TDLS discovery/setup and teardown * procedures should be performed by sending TDLS packets via * %NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be * used for asking the driver to perform a TDLS operation. * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ enum nl80211_attrs { /* don't change the order or add anything between, this is ABI! */ NL80211_ATTR_UNSPEC, NL80211_ATTR_WIPHY, NL80211_ATTR_WIPHY_NAME, NL80211_ATTR_IFINDEX, NL80211_ATTR_IFNAME, NL80211_ATTR_IFTYPE, NL80211_ATTR_MAC, NL80211_ATTR_KEY_DATA, NL80211_ATTR_KEY_IDX, NL80211_ATTR_KEY_CIPHER, NL80211_ATTR_KEY_SEQ, NL80211_ATTR_KEY_DEFAULT, NL80211_ATTR_BEACON_INTERVAL, NL80211_ATTR_DTIM_PERIOD, NL80211_ATTR_BEACON_HEAD, NL80211_ATTR_BEACON_TAIL, NL80211_ATTR_STA_AID, NL80211_ATTR_STA_FLAGS, NL80211_ATTR_STA_LISTEN_INTERVAL, NL80211_ATTR_STA_SUPPORTED_RATES, NL80211_ATTR_STA_VLAN, NL80211_ATTR_STA_INFO, NL80211_ATTR_WIPHY_BANDS, NL80211_ATTR_MNTR_FLAGS, NL80211_ATTR_MESH_ID, NL80211_ATTR_STA_PLINK_ACTION, NL80211_ATTR_MPATH_NEXT_HOP, NL80211_ATTR_MPATH_INFO, NL80211_ATTR_BSS_CTS_PROT, NL80211_ATTR_BSS_SHORT_PREAMBLE, NL80211_ATTR_BSS_SHORT_SLOT_TIME, NL80211_ATTR_HT_CAPABILITY, NL80211_ATTR_SUPPORTED_IFTYPES, NL80211_ATTR_REG_ALPHA2, NL80211_ATTR_REG_RULES, NL80211_ATTR_MESH_CONFIG, NL80211_ATTR_BSS_BASIC_RATES, NL80211_ATTR_WIPHY_TXQ_PARAMS, NL80211_ATTR_WIPHY_FREQ, NL80211_ATTR_WIPHY_CHANNEL_TYPE, NL80211_ATTR_KEY_DEFAULT_MGMT, NL80211_ATTR_MGMT_SUBTYPE, NL80211_ATTR_IE, NL80211_ATTR_MAX_NUM_SCAN_SSIDS, NL80211_ATTR_SCAN_FREQUENCIES, NL80211_ATTR_SCAN_SSIDS, NL80211_ATTR_GENERATION, /* replaces old SCAN_GENERATION */ NL80211_ATTR_BSS, NL80211_ATTR_REG_INITIATOR, NL80211_ATTR_REG_TYPE, NL80211_ATTR_SUPPORTED_COMMANDS, NL80211_ATTR_FRAME, NL80211_ATTR_SSID, NL80211_ATTR_AUTH_TYPE, NL80211_ATTR_REASON_CODE, NL80211_ATTR_KEY_TYPE, NL80211_ATTR_MAX_SCAN_IE_LEN, NL80211_ATTR_CIPHER_SUITES, NL80211_ATTR_FREQ_BEFORE, NL80211_ATTR_FREQ_AFTER, NL80211_ATTR_FREQ_FIXED, NL80211_ATTR_WIPHY_RETRY_SHORT, NL80211_ATTR_WIPHY_RETRY_LONG, NL80211_ATTR_WIPHY_FRAG_THRESHOLD, NL80211_ATTR_WIPHY_RTS_THRESHOLD, NL80211_ATTR_TIMED_OUT, NL80211_ATTR_USE_MFP, NL80211_ATTR_STA_FLAGS2, NL80211_ATTR_CONTROL_PORT, NL80211_ATTR_TESTDATA, NL80211_ATTR_PRIVACY, NL80211_ATTR_DISCONNECTED_BY_AP, NL80211_ATTR_STATUS_CODE, NL80211_ATTR_CIPHER_SUITES_PAIRWISE, NL80211_ATTR_CIPHER_SUITE_GROUP, NL80211_ATTR_WPA_VERSIONS, NL80211_ATTR_AKM_SUITES, NL80211_ATTR_REQ_IE, NL80211_ATTR_RESP_IE, NL80211_ATTR_PREV_BSSID, NL80211_ATTR_KEY, NL80211_ATTR_KEYS, NL80211_ATTR_PID, NL80211_ATTR_4ADDR, NL80211_ATTR_SURVEY_INFO, NL80211_ATTR_PMKID, NL80211_ATTR_MAX_NUM_PMKIDS, NL80211_ATTR_DURATION, NL80211_ATTR_COOKIE, NL80211_ATTR_WIPHY_COVERAGE_CLASS, NL80211_ATTR_TX_RATES, NL80211_ATTR_FRAME_MATCH, NL80211_ATTR_ACK, NL80211_ATTR_PS_STATE, NL80211_ATTR_CQM, NL80211_ATTR_LOCAL_STATE_CHANGE, NL80211_ATTR_AP_ISOLATE, NL80211_ATTR_WIPHY_TX_POWER_SETTING, NL80211_ATTR_WIPHY_TX_POWER_LEVEL, NL80211_ATTR_TX_FRAME_TYPES, NL80211_ATTR_RX_FRAME_TYPES, NL80211_ATTR_FRAME_TYPE, NL80211_ATTR_CONTROL_PORT_ETHERTYPE, NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, NL80211_ATTR_SUPPORT_IBSS_RSN, NL80211_ATTR_WIPHY_ANTENNA_TX, NL80211_ATTR_WIPHY_ANTENNA_RX, NL80211_ATTR_MCAST_RATE, NL80211_ATTR_OFFCHANNEL_TX_OK, NL80211_ATTR_BSS_HT_OPMODE, NL80211_ATTR_KEY_DEFAULT_TYPES, NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION, NL80211_ATTR_MESH_SETUP, NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX, NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX, NL80211_ATTR_SUPPORT_MESH_AUTH, NL80211_ATTR_STA_PLINK_STATE, NL80211_ATTR_WOWLAN_TRIGGERS, NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, NL80211_ATTR_SCHED_SCAN_INTERVAL, NL80211_ATTR_INTERFACE_COMBINATIONS, NL80211_ATTR_SOFTWARE_IFTYPES, NL80211_ATTR_REKEY_DATA, NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS, NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN, NL80211_ATTR_SCAN_SUPP_RATES, NL80211_ATTR_HIDDEN_SSID, NL80211_ATTR_IE_PROBE_RESP, NL80211_ATTR_IE_ASSOC_RESP, NL80211_ATTR_STA_WME, NL80211_ATTR_SUPPORT_AP_UAPSD, NL80211_ATTR_ROAM_SUPPORT, NL80211_ATTR_SCHED_SCAN_MATCH, NL80211_ATTR_MAX_MATCH_SETS, NL80211_ATTR_PMKSA_CANDIDATE, NL80211_ATTR_TX_NO_CCK_RATE, NL80211_ATTR_TDLS_ACTION, NL80211_ATTR_TDLS_DIALOG_TOKEN, NL80211_ATTR_TDLS_OPERATION, NL80211_ATTR_TDLS_SUPPORT, NL80211_ATTR_TDLS_EXTERNAL_SETUP, /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, NL80211_ATTR_MAX = __NL80211_ATTR_AFTER_LAST - 1 }; /* source-level API compatibility */ #define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION #define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG /* * Allow user space programs to use #ifdef on new attributes by defining them * here */ #define NL80211_CMD_CONNECT NL80211_CMD_CONNECT #define NL80211_ATTR_HT_CAPABILITY NL80211_ATTR_HT_CAPABILITY #define NL80211_ATTR_BSS_BASIC_RATES NL80211_ATTR_BSS_BASIC_RATES #define NL80211_ATTR_WIPHY_TXQ_PARAMS NL80211_ATTR_WIPHY_TXQ_PARAMS #define NL80211_ATTR_WIPHY_FREQ NL80211_ATTR_WIPHY_FREQ #define NL80211_ATTR_WIPHY_CHANNEL_TYPE NL80211_ATTR_WIPHY_CHANNEL_TYPE #define NL80211_ATTR_MGMT_SUBTYPE NL80211_ATTR_MGMT_SUBTYPE #define NL80211_ATTR_IE NL80211_ATTR_IE #define NL80211_ATTR_REG_INITIATOR NL80211_ATTR_REG_INITIATOR #define NL80211_ATTR_REG_TYPE NL80211_ATTR_REG_TYPE #define NL80211_ATTR_FRAME NL80211_ATTR_FRAME #define NL80211_ATTR_SSID NL80211_ATTR_SSID #define NL80211_ATTR_AUTH_TYPE NL80211_ATTR_AUTH_TYPE #define NL80211_ATTR_REASON_CODE NL80211_ATTR_REASON_CODE #define NL80211_ATTR_CIPHER_SUITES_PAIRWISE NL80211_ATTR_CIPHER_SUITES_PAIRWISE #define NL80211_ATTR_CIPHER_SUITE_GROUP NL80211_ATTR_CIPHER_SUITE_GROUP #define NL80211_ATTR_WPA_VERSIONS NL80211_ATTR_WPA_VERSIONS #define NL80211_ATTR_AKM_SUITES NL80211_ATTR_AKM_SUITES #define NL80211_ATTR_KEY NL80211_ATTR_KEY #define NL80211_ATTR_KEYS NL80211_ATTR_KEYS #define NL80211_MAX_SUPP_RATES 32 #define NL80211_MAX_SUPP_REG_RULES 32 #define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0 #define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16 #define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24 #define NL80211_HT_CAPABILITY_LEN 26 #define NL80211_MAX_NR_CIPHER_SUITES 5 #define NL80211_MAX_NR_AKM_SUITES 2 /** * enum nl80211_iftype - (virtual) interface types * * @NL80211_IFTYPE_UNSPECIFIED: unspecified type, driver decides * @NL80211_IFTYPE_ADHOC: independent BSS member * @NL80211_IFTYPE_STATION: managed BSS member * @NL80211_IFTYPE_AP: access point * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces * are a bit special in that they must always be tied to a pre-existing * AP type interface. * @NL80211_IFTYPE_WDS: wireless distribution interface * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames * @NL80211_IFTYPE_MESH_POINT: mesh point * @NL80211_IFTYPE_P2P_CLIENT: P2P client * @NL80211_IFTYPE_P2P_GO: P2P group owner * @NL80211_IFTYPE_MAX: highest interface type number currently defined * @NUM_NL80211_IFTYPES: number of defined interface types * * These values are used with the %NL80211_ATTR_IFTYPE * to set the type of an interface. * */ enum nl80211_iftype { NL80211_IFTYPE_UNSPECIFIED, NL80211_IFTYPE_ADHOC, NL80211_IFTYPE_STATION, NL80211_IFTYPE_AP, NL80211_IFTYPE_AP_VLAN, NL80211_IFTYPE_WDS, NL80211_IFTYPE_MONITOR, NL80211_IFTYPE_MESH_POINT, NL80211_IFTYPE_P2P_CLIENT, NL80211_IFTYPE_P2P_GO, /* keep last */ NUM_NL80211_IFTYPES, NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1 }; /** * enum nl80211_sta_flags - station flags * * Station flags. When a station is added to an AP interface, it is * assumed to be already associated (and hence authenticated.) * * @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved * @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X) * @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames * with short barker preamble * @NL80211_STA_FLAG_WME: station is WME/QoS capable * @NL80211_STA_FLAG_MFP: station uses management frame protection * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated * @NL80211_STA_FLAG_MAX: highest station flag number currently defined * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ enum nl80211_sta_flags { __NL80211_STA_FLAG_INVALID, NL80211_STA_FLAG_AUTHORIZED, NL80211_STA_FLAG_SHORT_PREAMBLE, NL80211_STA_FLAG_WME, NL80211_STA_FLAG_MFP, NL80211_STA_FLAG_AUTHENTICATED, /* keep last */ __NL80211_STA_FLAG_AFTER_LAST, NL80211_STA_FLAG_MAX = __NL80211_STA_FLAG_AFTER_LAST - 1 }; /** * struct nl80211_sta_flag_update - station flags mask/set * @mask: mask of station flags to set * @set: which values to set them to * * Both mask and set contain bits as per &enum nl80211_sta_flags. */ struct nl80211_sta_flag_update { __u32 mask; __u32 set; } __attribute__((packed)); /** * enum nl80211_rate_info - bitrate information * * These attribute types are used with %NL80211_STA_INFO_TXRATE * when getting information about the bitrate of a station. * * @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved * @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s) * @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8) * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 Mhz dualchannel bitrate * @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval * @NL80211_RATE_INFO_MAX: highest rate_info number currently defined * @__NL80211_RATE_INFO_AFTER_LAST: internal use */ enum nl80211_rate_info { __NL80211_RATE_INFO_INVALID, NL80211_RATE_INFO_BITRATE, NL80211_RATE_INFO_MCS, NL80211_RATE_INFO_40_MHZ_WIDTH, NL80211_RATE_INFO_SHORT_GI, /* keep last */ __NL80211_RATE_INFO_AFTER_LAST, NL80211_RATE_INFO_MAX = __NL80211_RATE_INFO_AFTER_LAST - 1 }; /** * enum nl80211_sta_bss_param - BSS information collected by STA * * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM * when getting information about the bitrate of a station. * * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved * @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag) * @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE: whether short preamble is enabled * (flag) * @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME: whether short slot time is enabled * (flag) * @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8) * @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16) * @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined * @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use */ enum nl80211_sta_bss_param { __NL80211_STA_BSS_PARAM_INVALID, NL80211_STA_BSS_PARAM_CTS_PROT, NL80211_STA_BSS_PARAM_SHORT_PREAMBLE, NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME, NL80211_STA_BSS_PARAM_DTIM_PERIOD, NL80211_STA_BSS_PARAM_BEACON_INTERVAL, /* keep last */ __NL80211_STA_BSS_PARAM_AFTER_LAST, NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1 }; /** * enum nl80211_sta_info - station information * * These attribute types are used with %NL80211_ATTR_STA_INFO * when getting information about a station. * * @__NL80211_STA_INFO_INVALID: attribute number 0 is reserved * @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs) * @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station) * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station) * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm) * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute * containing info as possible, see &enum nl80211_rate_info * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station) * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this * station) * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station) * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station) * @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm) * @NL80211_STA_INFO_LLID: the station's mesh LLID * @NL80211_STA_INFO_PLID: the station's mesh PLID * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station * (see %enum nl80211_plink_state) * @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested * attribute, like NL80211_STA_INFO_TX_BITRATE. * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute * containing info as possible, see &enum nl80211_sta_bss_param * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ enum nl80211_sta_info { __NL80211_STA_INFO_INVALID, NL80211_STA_INFO_INACTIVE_TIME, NL80211_STA_INFO_RX_BYTES, NL80211_STA_INFO_TX_BYTES, NL80211_STA_INFO_LLID, NL80211_STA_INFO_PLID, NL80211_STA_INFO_PLINK_STATE, NL80211_STA_INFO_SIGNAL, NL80211_STA_INFO_TX_BITRATE, NL80211_STA_INFO_RX_PACKETS, NL80211_STA_INFO_TX_PACKETS, NL80211_STA_INFO_TX_RETRIES, NL80211_STA_INFO_TX_FAILED, NL80211_STA_INFO_SIGNAL_AVG, NL80211_STA_INFO_RX_BITRATE, NL80211_STA_INFO_BSS_PARAM, NL80211_STA_INFO_CONNECTED_TIME, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, NL80211_STA_INFO_MAX = __NL80211_STA_INFO_AFTER_LAST - 1 }; /** * enum nl80211_mpath_flags - nl80211 mesh path flags * * @NL80211_MPATH_FLAG_ACTIVE: the mesh path is active * @NL80211_MPATH_FLAG_RESOLVING: the mesh path discovery process is running * @NL80211_MPATH_FLAG_SN_VALID: the mesh path contains a valid SN * @NL80211_MPATH_FLAG_FIXED: the mesh path has been manually set * @NL80211_MPATH_FLAG_RESOLVED: the mesh path discovery process succeeded */ enum nl80211_mpath_flags { NL80211_MPATH_FLAG_ACTIVE = 1<<0, NL80211_MPATH_FLAG_RESOLVING = 1<<1, NL80211_MPATH_FLAG_SN_VALID = 1<<2, NL80211_MPATH_FLAG_FIXED = 1<<3, NL80211_MPATH_FLAG_RESOLVED = 1<<4, }; /** * enum nl80211_mpath_info - mesh path information * * These attribute types are used with %NL80211_ATTR_MPATH_INFO when getting * information about a mesh path. * * @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved * @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination * @NL80211_MPATH_INFO_SN: destination sequence number * @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path * @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now * @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in * &enum nl80211_mpath_flags; * @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec * @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries * @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number * currently defind * @__NL80211_MPATH_INFO_AFTER_LAST: internal use */ enum nl80211_mpath_info { __NL80211_MPATH_INFO_INVALID, NL80211_MPATH_INFO_FRAME_QLEN, NL80211_MPATH_INFO_SN, NL80211_MPATH_INFO_METRIC, NL80211_MPATH_INFO_EXPTIME, NL80211_MPATH_INFO_FLAGS, NL80211_MPATH_INFO_DISCOVERY_TIMEOUT, NL80211_MPATH_INFO_DISCOVERY_RETRIES, /* keep last */ __NL80211_MPATH_INFO_AFTER_LAST, NL80211_MPATH_INFO_MAX = __NL80211_MPATH_INFO_AFTER_LAST - 1 }; /** * enum nl80211_band_attr - band attributes * @__NL80211_BAND_ATTR_INVALID: attribute number 0 is reserved * @NL80211_BAND_ATTR_FREQS: supported frequencies in this band, * an array of nested frequency attributes * @NL80211_BAND_ATTR_RATES: supported bitrates in this band, * an array of nested bitrate attributes * @NL80211_BAND_ATTR_HT_MCS_SET: 16-byte attribute containing the MCS set as * defined in 802.11n * @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined * @__NL80211_BAND_ATTR_AFTER_LAST: internal use */ enum nl80211_band_attr { __NL80211_BAND_ATTR_INVALID, NL80211_BAND_ATTR_FREQS, NL80211_BAND_ATTR_RATES, NL80211_BAND_ATTR_HT_MCS_SET, NL80211_BAND_ATTR_HT_CAPA, NL80211_BAND_ATTR_HT_AMPDU_FACTOR, NL80211_BAND_ATTR_HT_AMPDU_DENSITY, /* keep last */ __NL80211_BAND_ATTR_AFTER_LAST, NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1 }; #define NL80211_BAND_ATTR_HT_CAPA NL80211_BAND_ATTR_HT_CAPA /** * enum nl80211_frequency_attr - frequency attributes * @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current * regulatory domain. * @NL80211_FREQUENCY_ATTR_PASSIVE_SCAN: Only passive scanning is * permitted on this channel in current regulatory domain. * @NL80211_FREQUENCY_ATTR_NO_IBSS: IBSS networks are not permitted * on this channel in current regulatory domain. * @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory * on this channel in current regulatory domain. * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm * (100 * dBm). * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number * currently defined * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use */ enum nl80211_frequency_attr { __NL80211_FREQUENCY_ATTR_INVALID, NL80211_FREQUENCY_ATTR_FREQ, NL80211_FREQUENCY_ATTR_DISABLED, NL80211_FREQUENCY_ATTR_PASSIVE_SCAN, NL80211_FREQUENCY_ATTR_NO_IBSS, NL80211_FREQUENCY_ATTR_RADAR, NL80211_FREQUENCY_ATTR_MAX_TX_POWER, /* keep last */ __NL80211_FREQUENCY_ATTR_AFTER_LAST, NL80211_FREQUENCY_ATTR_MAX = __NL80211_FREQUENCY_ATTR_AFTER_LAST - 1 }; #define NL80211_FREQUENCY_ATTR_MAX_TX_POWER NL80211_FREQUENCY_ATTR_MAX_TX_POWER /** * enum nl80211_bitrate_attr - bitrate attributes * @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved * @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps * @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported * in 2.4 GHz band. * @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number * currently defined * @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use */ enum nl80211_bitrate_attr { __NL80211_BITRATE_ATTR_INVALID, NL80211_BITRATE_ATTR_RATE, NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE, /* keep last */ __NL80211_BITRATE_ATTR_AFTER_LAST, NL80211_BITRATE_ATTR_MAX = __NL80211_BITRATE_ATTR_AFTER_LAST - 1 }; /** * enum nl80211_initiator - Indicates the initiator of a reg domain request * @NL80211_REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world * regulatory domain. * @NL80211_REGDOM_SET_BY_USER: User asked the wireless core to set the * regulatory domain. * @NL80211_REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the * wireless core it thinks its knows the regulatory domain we should be in. * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an * 802.11 country information element with regulatory information it * thinks we should consider. cfg80211 only processes the country * code from the IE, and relies on the regulatory domain information * structure passed by userspace (CRDA) from our wireless-regdb. * If a channel is enabled but the country code indicates it should * be disabled we disable the channel and re-enable it upon disassociation. */ enum nl80211_reg_initiator { NL80211_REGDOM_SET_BY_CORE, NL80211_REGDOM_SET_BY_USER, NL80211_REGDOM_SET_BY_DRIVER, NL80211_REGDOM_SET_BY_COUNTRY_IE, }; /** * enum nl80211_reg_type - specifies the type of regulatory domain * @NL80211_REGDOM_TYPE_COUNTRY: the regulatory domain set is one that pertains * to a specific country. When this is set you can count on the * ISO / IEC 3166 alpha2 country code being valid. * @NL80211_REGDOM_TYPE_WORLD: the regulatory set domain is the world regulatory * domain. * @NL80211_REGDOM_TYPE_CUSTOM_WORLD: the regulatory domain set is a custom * driver specific world regulatory domain. These do not apply system-wide * and are only applicable to the individual devices which have requested * them to be applied. * @NL80211_REGDOM_TYPE_INTERSECTION: the regulatory domain set is the product * of an intersection between two regulatory domains -- the previously * set regulatory domain on the system and the last accepted regulatory * domain request to be processed. */ enum nl80211_reg_type { NL80211_REGDOM_TYPE_COUNTRY, NL80211_REGDOM_TYPE_WORLD, NL80211_REGDOM_TYPE_CUSTOM_WORLD, NL80211_REGDOM_TYPE_INTERSECTION, }; /** * enum nl80211_reg_rule_attr - regulatory rule attributes * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved * @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional * considerations for a given frequency range. These are the * &enum nl80211_reg_rule_flags. * @NL80211_ATTR_FREQ_RANGE_START: starting frequencry for the regulatory * rule in KHz. This is not a center of frequency but an actual regulatory * band edge. * @NL80211_ATTR_FREQ_RANGE_END: ending frequency for the regulatory rule * in KHz. This is not a center a frequency but an actual regulatory * band edge. * @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this * frequency range, in KHz. * @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain * for a given frequency range. The value is in mBi (100 * dBi). * If you don't have one then don't send this. * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for * a given frequency range. The value is in mBm (100 * dBm). * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number * currently defined * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use */ enum nl80211_reg_rule_attr { __NL80211_REG_RULE_ATTR_INVALID, NL80211_ATTR_REG_RULE_FLAGS, NL80211_ATTR_FREQ_RANGE_START, NL80211_ATTR_FREQ_RANGE_END, NL80211_ATTR_FREQ_RANGE_MAX_BW, NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN, NL80211_ATTR_POWER_RULE_MAX_EIRP, /* keep last */ __NL80211_REG_RULE_ATTR_AFTER_LAST, NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1 }; /** * enum nl80211_sched_scan_match_attr - scheduled scan match attributes * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching, * only report BSS with matching SSID. * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter * attribute number currently defined * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use */ enum nl80211_sched_scan_match_attr { __NL80211_SCHED_SCAN_MATCH_ATTR_INVALID, NL80211_ATTR_SCHED_SCAN_MATCH_SSID, /* keep last */ __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST, NL80211_SCHED_SCAN_MATCH_ATTR_MAX = __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1 }; /** * enum nl80211_reg_rule_flags - regulatory rule flags * * @NL80211_RRF_NO_OFDM: OFDM modulation not allowed * @NL80211_RRF_NO_CCK: CCK modulation not allowed * @NL80211_RRF_NO_INDOOR: indoor operation not allowed * @NL80211_RRF_NO_OUTDOOR: outdoor operation not allowed * @NL80211_RRF_DFS: DFS support is required to be used * @NL80211_RRF_PTP_ONLY: this is only for Point To Point links * @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links * @NL80211_RRF_PASSIVE_SCAN: passive scan is required * @NL80211_RRF_NO_IBSS: no IBSS is allowed */ enum nl80211_reg_rule_flags { NL80211_RRF_NO_OFDM = 1<<0, NL80211_RRF_NO_CCK = 1<<1, NL80211_RRF_NO_INDOOR = 1<<2, NL80211_RRF_NO_OUTDOOR = 1<<3, NL80211_RRF_DFS = 1<<4, NL80211_RRF_PTP_ONLY = 1<<5, NL80211_RRF_PTMP_ONLY = 1<<6, NL80211_RRF_PASSIVE_SCAN = 1<<7, NL80211_RRF_NO_IBSS = 1<<8, }; /** * enum nl80211_survey_info - survey information * * These attribute types are used with %NL80211_ATTR_SURVEY_INFO * when getting information about a survey. * * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm) * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used * @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio * spent on this channel * @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary * channel was sensed busy (either due to activity or energy detect) * @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension * channel was sensed busy * @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent * receiving data * @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent * transmitting data * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number * currently defined * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use */ enum nl80211_survey_info { __NL80211_SURVEY_INFO_INVALID, NL80211_SURVEY_INFO_FREQUENCY, NL80211_SURVEY_INFO_NOISE, NL80211_SURVEY_INFO_IN_USE, NL80211_SURVEY_INFO_CHANNEL_TIME, NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY, NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY, NL80211_SURVEY_INFO_CHANNEL_TIME_RX, NL80211_SURVEY_INFO_CHANNEL_TIME_TX, /* keep last */ __NL80211_SURVEY_INFO_AFTER_LAST, NL80211_SURVEY_INFO_MAX = __NL80211_SURVEY_INFO_AFTER_LAST - 1 }; /** * enum nl80211_mntr_flags - monitor configuration flags * * Monitor configuration flags. * * @__NL80211_MNTR_FLAG_INVALID: reserved * * @NL80211_MNTR_FLAG_FCSFAIL: pass frames with bad FCS * @NL80211_MNTR_FLAG_PLCPFAIL: pass frames with bad PLCP * @NL80211_MNTR_FLAG_CONTROL: pass control frames * @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering * @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing. * overrides all other flags. * * @__NL80211_MNTR_FLAG_AFTER_LAST: internal use * @NL80211_MNTR_FLAG_MAX: highest possible monitor flag */ enum nl80211_mntr_flags { __NL80211_MNTR_FLAG_INVALID, NL80211_MNTR_FLAG_FCSFAIL, NL80211_MNTR_FLAG_PLCPFAIL, NL80211_MNTR_FLAG_CONTROL, NL80211_MNTR_FLAG_OTHER_BSS, NL80211_MNTR_FLAG_COOK_FRAMES, /* keep last */ __NL80211_MNTR_FLAG_AFTER_LAST, NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1 }; /** * enum nl80211_meshconf_params - mesh configuration parameters * * Mesh configuration parameters. These can be changed while the mesh is * active. * * @__NL80211_MESHCONF_INVALID: internal use * * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in * millisecond units, used by the Peer Link Open message * * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in * millisecond units, used by the peer link management to close a peer link * * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in * millisecond units * * @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed * on this mesh interface * * @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link * open retries that can be sent to establish a new peer link instance in a * mesh * * @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh * point. * * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically * open peer links when we detect compatible mesh peers. * * @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames * containing a PREQ that an MP can send to a particular destination (path * target) * * @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths * (in milliseconds) * * @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait * until giving up on a path discovery (in milliseconds) * * @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh * points receiving a PREQ shall consider the forwarding information from the * root to be valid. (TU = time unit) * * @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in * TUs) during which an MP can send only one action frame containing a PREQ * reference element * * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs) * that it takes for an HWMP information element to propagate across the mesh * * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not * * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a * source mesh point for path selection elements. * * @NL80211_MESHCONF_HWMP_RANN_INTERVAL: The interval of time (in TUs) between * root announcements are transmitted. * * @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has * access to a broader network beyond the MBSS. This is done via Root * Announcement frames. * * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use */ enum nl80211_meshconf_params { __NL80211_MESHCONF_INVALID, NL80211_MESHCONF_RETRY_TIMEOUT, NL80211_MESHCONF_CONFIRM_TIMEOUT, NL80211_MESHCONF_HOLDING_TIMEOUT, NL80211_MESHCONF_MAX_PEER_LINKS, NL80211_MESHCONF_MAX_RETRIES, NL80211_MESHCONF_TTL, NL80211_MESHCONF_AUTO_OPEN_PLINKS, NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES, NL80211_MESHCONF_PATH_REFRESH_TIME, NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT, NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT, NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL, NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME, NL80211_MESHCONF_HWMP_ROOTMODE, NL80211_MESHCONF_ELEMENT_TTL, NL80211_MESHCONF_HWMP_RANN_INTERVAL, NL80211_MESHCONF_GATE_ANNOUNCEMENTS, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, NL80211_MESHCONF_ATTR_MAX = __NL80211_MESHCONF_ATTR_AFTER_LAST - 1 }; /** * enum nl80211_mesh_setup_params - mesh setup parameters * * Mesh setup parameters. These are used to start/join a mesh and cannot be * changed while the mesh is active. * * @__NL80211_MESH_SETUP_INVALID: Internal use * * @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a * vendor specific path selection algorithm or disable it to use the default * HWMP. * * @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a * vendor specific path metric or disable it to use the default Airtime * metric. * * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a * robust security network ie, or a vendor specific information element that * vendors will use to identify the path selection methods and metrics in use. * * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication * daemon will be authenticating mesh candidates. * * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication * daemon will be securing peer link frames. AMPE is a secured version of Mesh * Peering Management (MPM) and is implemented with the assistance of a * userspace daemon. When this flag is set, the kernel will send peer * management frames to a userspace daemon that will implement AMPE * functionality (security capabilities selection, key confirmation, and key * management). When the flag is unset (default), the kernel can autonomously * complete (unsecured) mesh peering without the need of a userspace daemon. * * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use */ enum nl80211_mesh_setup_params { __NL80211_MESH_SETUP_INVALID, NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL, NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC, NL80211_MESH_SETUP_IE, NL80211_MESH_SETUP_USERSPACE_AUTH, NL80211_MESH_SETUP_USERSPACE_AMPE, /* keep last */ __NL80211_MESH_SETUP_ATTR_AFTER_LAST, NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1 }; /** * enum nl80211_txq_attr - TX queue parameter attributes * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved * @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*) * @NL80211_TXQ_ATTR_TXOP: Maximum burst time in units of 32 usecs, 0 meaning * disabled * @NL80211_TXQ_ATTR_CWMIN: Minimum contention window [a value of the form * 2^n-1 in the range 1..32767] * @NL80211_TXQ_ATTR_CWMAX: Maximum contention window [a value of the form * 2^n-1 in the range 1..32767] * @NL80211_TXQ_ATTR_AIFS: Arbitration interframe space [0..255] * @__NL80211_TXQ_ATTR_AFTER_LAST: Internal * @NL80211_TXQ_ATTR_MAX: Maximum TXQ attribute number */ enum nl80211_txq_attr { __NL80211_TXQ_ATTR_INVALID, NL80211_TXQ_ATTR_QUEUE, NL80211_TXQ_ATTR_TXOP, NL80211_TXQ_ATTR_CWMIN, NL80211_TXQ_ATTR_CWMAX, NL80211_TXQ_ATTR_AIFS, /* keep last */ __NL80211_TXQ_ATTR_AFTER_LAST, NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1 }; enum nl80211_txq_q { NL80211_TXQ_Q_VO, NL80211_TXQ_Q_VI, NL80211_TXQ_Q_BE, NL80211_TXQ_Q_BK }; enum nl80211_channel_type { NL80211_CHAN_NO_HT, NL80211_CHAN_HT20, NL80211_CHAN_HT40MINUS, NL80211_CHAN_HT40PLUS }; /** * enum nl80211_bss - netlink attributes for a BSS * * @__NL80211_BSS_INVALID: invalid * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets) * @NL80211_BSS_FREQUENCY: frequency in MHz (u32) * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64) * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16) * @NL80211_BSS_CAPABILITY: capability field (CPU order, u16) * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the * raw information elements from the probe response/beacon (bin); * if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are * from a Probe Response frame; otherwise they are from a Beacon frame. * However, if the driver does not indicate the source of the IEs, these * IEs may be from either frame subtype. * @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon * in mBm (100 * dBm) (s32) * @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon * in unspecified units, scaled to 0..100 (u8) * @NL80211_BSS_STATUS: status, if this BSS is "used" * @NL80211_BSS_SEEN_MS_AGO: age of this BSS entry in ms * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information * elements from a Beacon frame (bin); not present if no Beacon frame has * yet been received * @__NL80211_BSS_AFTER_LAST: internal * @NL80211_BSS_MAX: highest BSS attribute */ enum nl80211_bss { __NL80211_BSS_INVALID, NL80211_BSS_BSSID, NL80211_BSS_FREQUENCY, NL80211_BSS_TSF, NL80211_BSS_BEACON_INTERVAL, NL80211_BSS_CAPABILITY, NL80211_BSS_INFORMATION_ELEMENTS, NL80211_BSS_SIGNAL_MBM, NL80211_BSS_SIGNAL_UNSPEC, NL80211_BSS_STATUS, NL80211_BSS_SEEN_MS_AGO, NL80211_BSS_BEACON_IES, /* keep last */ __NL80211_BSS_AFTER_LAST, NL80211_BSS_MAX = __NL80211_BSS_AFTER_LAST - 1 }; /** * enum nl80211_bss_status - BSS "status" * @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS. * @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS. * @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS. * * The BSS status is a BSS attribute in scan dumps, which * indicates the status the interface has wrt. this BSS. */ enum nl80211_bss_status { NL80211_BSS_STATUS_AUTHENTICATED, NL80211_BSS_STATUS_ASSOCIATED, NL80211_BSS_STATUS_IBSS_JOINED, }; /** * enum nl80211_auth_type - AuthenticationType * * @NL80211_AUTHTYPE_OPEN_SYSTEM: Open System authentication * @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only) * @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r) * @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP) * @__NL80211_AUTHTYPE_NUM: internal * @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm * @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by * trying multiple times); this is invalid in netlink -- leave out * the attribute for this on CONNECT commands. */ enum nl80211_auth_type { NL80211_AUTHTYPE_OPEN_SYSTEM, NL80211_AUTHTYPE_SHARED_KEY, NL80211_AUTHTYPE_FT, NL80211_AUTHTYPE_NETWORK_EAP, /* keep last */ __NL80211_AUTHTYPE_NUM, NL80211_AUTHTYPE_MAX = __NL80211_AUTHTYPE_NUM - 1, NL80211_AUTHTYPE_AUTOMATIC }; /** * enum nl80211_key_type - Key Type * @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key * @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key * @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS) * @NUM_NL80211_KEYTYPES: number of defined key types */ enum nl80211_key_type { NL80211_KEYTYPE_GROUP, NL80211_KEYTYPE_PAIRWISE, NL80211_KEYTYPE_PEERKEY, NUM_NL80211_KEYTYPES }; /** * enum nl80211_mfp - Management frame protection state * @NL80211_MFP_NO: Management frame protection not used * @NL80211_MFP_REQUIRED: Management frame protection required */ enum nl80211_mfp { NL80211_MFP_NO, NL80211_MFP_REQUIRED, }; enum nl80211_wpa_versions { NL80211_WPA_VERSION_1 = 1 << 0, NL80211_WPA_VERSION_2 = 1 << 1, }; /** * enum nl80211_key_default_types - key default types * @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid * @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default * unicast key * @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default * multicast key * @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types */ enum nl80211_key_default_types { __NL80211_KEY_DEFAULT_TYPE_INVALID, NL80211_KEY_DEFAULT_TYPE_UNICAST, NL80211_KEY_DEFAULT_TYPE_MULTICAST, NUM_NL80211_KEY_DEFAULT_TYPES }; /** * enum nl80211_key_attributes - key attributes * @__NL80211_KEY_INVALID: invalid * @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of * 16 bytes encryption key followed by 8 bytes each for TX and RX MIC * keys * @NL80211_KEY_IDX: key ID (u8, 0-3) * @NL80211_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11 * section 7.3.2.25.1, e.g. 0x000FAC04) * @NL80211_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and * CCMP keys, each six bytes in little endian * @NL80211_KEY_DEFAULT: flag indicating default key * @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not * specified the default depends on whether a MAC address was * given with the command using the key or not (u32) * @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags * attributes, specifying what a key should be set as default as. * See &enum nl80211_key_default_types. * @__NL80211_KEY_AFTER_LAST: internal * @NL80211_KEY_MAX: highest key attribute */ enum nl80211_key_attributes { __NL80211_KEY_INVALID, NL80211_KEY_DATA, NL80211_KEY_IDX, NL80211_KEY_CIPHER, NL80211_KEY_SEQ, NL80211_KEY_DEFAULT, NL80211_KEY_DEFAULT_MGMT, NL80211_KEY_TYPE, NL80211_KEY_DEFAULT_TYPES, /* keep last */ __NL80211_KEY_AFTER_LAST, NL80211_KEY_MAX = __NL80211_KEY_AFTER_LAST - 1 }; /** * enum nl80211_tx_rate_attributes - TX rate set attributes * @__NL80211_TXRATE_INVALID: invalid * @NL80211_TXRATE_LEGACY: Legacy (non-MCS) rates allowed for TX rate selection * in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with * 1 = 500 kbps) but without the IE length restriction (at most * %NL80211_MAX_SUPP_RATES in a single array). * @__NL80211_TXRATE_AFTER_LAST: internal * @NL80211_TXRATE_MAX: highest TX rate attribute */ enum nl80211_tx_rate_attributes { __NL80211_TXRATE_INVALID, NL80211_TXRATE_LEGACY, /* keep last */ __NL80211_TXRATE_AFTER_LAST, NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1 }; /** * enum nl80211_band - Frequency band * @NL80211_BAND_2GHZ: 2.4 GHz ISM band * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz) */ enum nl80211_band { NL80211_BAND_2GHZ, NL80211_BAND_5GHZ, }; enum nl80211_ps_state { NL80211_PS_DISABLED, NL80211_PS_ENABLED, }; /** * enum nl80211_attr_cqm - connection quality monitor attributes * @__NL80211_ATTR_CQM_INVALID: invalid * @NL80211_ATTR_CQM_RSSI_THOLD: RSSI threshold in dBm. This value specifies * the threshold for the RSSI level at which an event will be sent. Zero * to disable. * @NL80211_ATTR_CQM_RSSI_HYST: RSSI hysteresis in dBm. This value specifies * the minimum amount the RSSI level must change after an event before a * new event may be issued (to reduce effects of RSSI oscillation). * @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event * @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many * consecutive packets were not acknowledged by the peer * @__NL80211_ATTR_CQM_AFTER_LAST: internal * @NL80211_ATTR_CQM_MAX: highest key attribute */ enum nl80211_attr_cqm { __NL80211_ATTR_CQM_INVALID, NL80211_ATTR_CQM_RSSI_THOLD, NL80211_ATTR_CQM_RSSI_HYST, NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT, NL80211_ATTR_CQM_PKT_LOSS_EVENT, /* keep last */ __NL80211_ATTR_CQM_AFTER_LAST, NL80211_ATTR_CQM_MAX = __NL80211_ATTR_CQM_AFTER_LAST - 1 }; /** * enum nl80211_cqm_rssi_threshold_event - RSSI threshold event * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the * configured threshold * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the * configured threshold */ enum nl80211_cqm_rssi_threshold_event { NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW, NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH, }; /** * enum nl80211_tx_power_setting - TX power adjustment * @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power * @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter * @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter */ enum nl80211_tx_power_setting { NL80211_TX_POWER_AUTOMATIC, NL80211_TX_POWER_LIMITED, NL80211_TX_POWER_FIXED, }; /** * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has * a zero bit are ignored * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have * a bit for each byte in the pattern. The lowest-order bit corresponds * to the first byte of the pattern, but the bytes of the pattern are * in a little-endian-like format, i.e. the 9th byte of the pattern * corresponds to the lowest-order bit in the second byte of the mask. * For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where * xx indicates "don't care") would be represented by a pattern of * twelve zero bytes, and a mask of "0xed,0x07". * Note that the pattern matching is done as though frames were not * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked * first (including SNAP header unpacking) and then matched. * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number */ enum nl80211_wowlan_packet_pattern_attr { __NL80211_WOWLAN_PKTPAT_INVALID, NL80211_WOWLAN_PKTPAT_MASK, NL80211_WOWLAN_PKTPAT_PATTERN, NUM_NL80211_WOWLAN_PKTPAT, MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1, }; /** * struct nl80211_wowlan_pattern_support - pattern support information * @max_patterns: maximum number of patterns supported * @min_pattern_len: minimum length of each pattern * @max_pattern_len: maximum length of each pattern * * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the * capability information given by the kernel to userspace. */ struct nl80211_wowlan_pattern_support { __u32 max_patterns; __u32 min_pattern_len; __u32 max_pattern_len; } __attribute__((packed)); /** * enum nl80211_wowlan_triggers - WoWLAN trigger definitions * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes * @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put * the chip into a special state -- works best with chips that have * support for low-power operation already (flag) * @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect * is detected is implementation-specific (flag) * @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed * by 16 repetitions of MAC addr, anywhere in payload) (flag) * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns * which are passed in an array of nested attributes, each nested attribute * defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern. * Each pattern defines a wakeup packet. The matching is done on the MSDU, * i.e. as though the packet was an 802.3 packet, so the pattern matching * is done after the packet is converted to the MSDU. * * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute * carrying a &struct nl80211_wowlan_pattern_support. * @NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED: Not a real trigger, and cannot be * used when setting, used only to indicate that GTK rekeying is supported * by the device (flag) * @NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE: wake up on GTK rekey failure (if * done by the device) (flag) * @NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST: wake up on EAP Identity Request * packet (flag) * @NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE: wake up on 4-way handshake (flag) * @NL80211_WOWLAN_TRIG_RFKILL_RELEASE: wake up when rfkill is released * (on devices that have rfkill in the device) (flag) * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number */ enum nl80211_wowlan_triggers { __NL80211_WOWLAN_TRIG_INVALID, NL80211_WOWLAN_TRIG_ANY, NL80211_WOWLAN_TRIG_DISCONNECT, NL80211_WOWLAN_TRIG_MAGIC_PKT, NL80211_WOWLAN_TRIG_PKT_PATTERN, NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED, NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE, NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST, NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE, NL80211_WOWLAN_TRIG_RFKILL_RELEASE, /* keep last */ NUM_NL80211_WOWLAN_TRIG, MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1 }; /** * enum nl80211_iface_limit_attrs - limit attributes * @NL80211_IFACE_LIMIT_UNSPEC: (reserved) * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that * can be chosen from this set of interface types (u32) * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a * flag attribute for each interface type in this set * @NUM_NL80211_IFACE_LIMIT: number of attributes * @MAX_NL80211_IFACE_LIMIT: highest attribute number */ enum nl80211_iface_limit_attrs { NL80211_IFACE_LIMIT_UNSPEC, NL80211_IFACE_LIMIT_MAX, NL80211_IFACE_LIMIT_TYPES, /* keep last */ NUM_NL80211_IFACE_LIMIT, MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1 }; /** * enum nl80211_if_combination_attrs -- interface combination attributes * * @NL80211_IFACE_COMB_UNSPEC: (reserved) * @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits * for given interface types, see &enum nl80211_iface_limit_attrs. * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of * interfaces that can be created in this group. This number doesn't * apply to interfaces purely managed in software, which are listed * in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE. * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that * beacon intervals within this group must be all the same even for * infrastructure and AP/GO combinations, i.e. the GO(s) must adopt * the infrastructure network's beacon interval. * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many * different channels may be used within this group. * @NUM_NL80211_IFACE_COMB: number of attributes * @MAX_NL80211_IFACE_COMB: highest attribute number * * Examples: * limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2 * => allows an AP and a STA that must match BIs * * numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8 * => allows 8 of AP/GO * * numbers = [ #{STA} <= 2 ], channels = 2, max = 2 * => allows two STAs on different channels * * numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4 * => allows a STA plus three P2P interfaces * * The list of these four possiblities could completely be contained * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate * that any of these groups must match. * * "Combinations" of just a single interface will not be listed here, * a single interface of any valid interface type is assumed to always * be possible by itself. This means that implicitly, for each valid * interface type, the following group always exists: * numbers = [ #{} <= 1 ], channels = 1, max = 1 */ enum nl80211_if_combination_attrs { NL80211_IFACE_COMB_UNSPEC, NL80211_IFACE_COMB_LIMITS, NL80211_IFACE_COMB_MAXNUM, NL80211_IFACE_COMB_STA_AP_BI_MATCH, NL80211_IFACE_COMB_NUM_CHANNELS, /* keep last */ NUM_NL80211_IFACE_COMB, MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1 }; /** * enum nl80211_plink_state - state of a mesh peer link finite state machine * * @NL80211_PLINK_LISTEN: initial state, considered the implicit * state of non existant mesh peer links * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to * this mesh peer * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received * from this mesh peer * @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been * received from this mesh peer * @NL80211_PLINK_ESTAB: mesh peer link is established * @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled * @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh * plink are discarded * @NUM_NL80211_PLINK_STATES: number of peer link states * @MAX_NL80211_PLINK_STATES: highest numerical value of plink states */ enum nl80211_plink_state { NL80211_PLINK_LISTEN, NL80211_PLINK_OPN_SNT, NL80211_PLINK_OPN_RCVD, NL80211_PLINK_CNF_RCVD, NL80211_PLINK_ESTAB, NL80211_PLINK_HOLDING, NL80211_PLINK_BLOCKED, /* keep last */ NUM_NL80211_PLINK_STATES, MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1 }; #define NL80211_KCK_LEN 16 #define NL80211_KEK_LEN 16 #define NL80211_REPLAY_CTR_LEN 8 /** * enum nl80211_rekey_data - attributes for GTK rekey offload * @__NL80211_REKEY_DATA_INVALID: invalid number for nested attributes * @NL80211_REKEY_DATA_KEK: key encryption key (binary) * @NL80211_REKEY_DATA_KCK: key confirmation key (binary) * @NL80211_REKEY_DATA_REPLAY_CTR: replay counter (binary) * @NUM_NL80211_REKEY_DATA: number of rekey attributes (internal) * @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal) */ enum nl80211_rekey_data { __NL80211_REKEY_DATA_INVALID, NL80211_REKEY_DATA_KEK, NL80211_REKEY_DATA_KCK, NL80211_REKEY_DATA_REPLAY_CTR, /* keep last */ NUM_NL80211_REKEY_DATA, MAX_NL80211_REKEY_DATA = NUM_NL80211_REKEY_DATA - 1 }; /** * enum nl80211_hidden_ssid - values for %NL80211_ATTR_HIDDEN_SSID * @NL80211_HIDDEN_SSID_NOT_IN_USE: do not hide SSID (i.e., broadcast it in * Beacon frames) * @NL80211_HIDDEN_SSID_ZERO_LEN: hide SSID by using zero-length SSID element * in Beacon frames * @NL80211_HIDDEN_SSID_ZERO_CONTENTS: hide SSID by using correct length of SSID * element in Beacon frames but zero out each byte in the SSID */ enum nl80211_hidden_ssid { NL80211_HIDDEN_SSID_NOT_IN_USE, NL80211_HIDDEN_SSID_ZERO_LEN, NL80211_HIDDEN_SSID_ZERO_CONTENTS }; /** * enum nl80211_sta_wme_attr - station WME attributes * @__NL80211_STA_WME_INVALID: invalid number for nested attribute * @NL80211_STA_WME_UAPSD_QUEUES: bitmap of uapsd queues. the format * is the same as the AC bitmap in the QoS info field. * @NL80211_STA_WME_MAX_SP: max service period. the format is the same * as the MAX_SP field in the QoS info field (but already shifted down). * @__NL80211_STA_WME_AFTER_LAST: internal * @NL80211_STA_WME_MAX: highest station WME attribute */ enum nl80211_sta_wme_attr { __NL80211_STA_WME_INVALID, NL80211_STA_WME_UAPSD_QUEUES, NL80211_STA_WME_MAX_SP, /* keep last */ __NL80211_STA_WME_AFTER_LAST, NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1 }; /** * enum nl80211_pmksa_candidate_attr - attributes for PMKSA caching candidates * @__NL80211_PMKSA_CANDIDATE_INVALID: invalid number for nested attributes * @NL80211_PMKSA_CANDIDATE_INDEX: candidate index (u32; the smaller, the higher * priority) * @NL80211_PMKSA_CANDIDATE_BSSID: candidate BSSID (6 octets) * @NL80211_PMKSA_CANDIDATE_PREAUTH: RSN pre-authentication supported (flag) * @NUM_NL80211_PMKSA_CANDIDATE: number of PMKSA caching candidate attributes * (internal) * @MAX_NL80211_PMKSA_CANDIDATE: highest PMKSA caching candidate attribute * (internal) */ enum nl80211_pmksa_candidate_attr { __NL80211_PMKSA_CANDIDATE_INVALID, NL80211_PMKSA_CANDIDATE_INDEX, NL80211_PMKSA_CANDIDATE_BSSID, NL80211_PMKSA_CANDIDATE_PREAUTH, /* keep last */ NUM_NL80211_PMKSA_CANDIDATE, MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1 }; /** * enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION * @NL80211_TDLS_DISCOVERY_REQ: Send a TDLS discovery request * @NL80211_TDLS_SETUP: Setup TDLS link * @NL80211_TDLS_TEARDOWN: Teardown a TDLS link which is already established * @NL80211_TDLS_ENABLE_LINK: Enable TDLS link * @NL80211_TDLS_DISABLE_LINK: Disable TDLS link */ enum nl80211_tdls_operation { NL80211_TDLS_DISCOVERY_REQ, NL80211_TDLS_SETUP, NL80211_TDLS_TEARDOWN, NL80211_TDLS_ENABLE_LINK, NL80211_TDLS_DISABLE_LINK, }; #endif /* __LINUX_NL80211_H */