# # Network configuration # menuconfig NET bool "Networking support" select NLATTR select GENERIC_NET_UTILS ---help--- Unless you really know what you are doing, you should say Y here. The reason is that some programs need kernel networking support even when running on a stand-alone machine that isn't connected to any other computer. If you are upgrading from an older kernel, you should consider updating your networking tools too because changes in the kernel and the tools often go hand in hand. The tools are contained in the package net-tools, the location and version number of which are given in <file:Documentation/Changes>. For a general introduction to Linux networking, it is highly recommended to read the NET-HOWTO, available from <http://www.tldp.org/docs.html#howto>. if NET config WANT_COMPAT_NETLINK_MESSAGES bool help This option can be selected by other options that need compat netlink messages. config COMPAT_NETLINK_MESSAGES def_bool y depends on COMPAT depends on WEXT_CORE || WANT_COMPAT_NETLINK_MESSAGES help This option makes it possible to send different netlink messages to tasks depending on whether the task is a compat task or not. To achieve this, you need to set skb_shinfo(skb)->frag_list to the compat skb before sending the skb, the netlink code will sort out which message to actually pass to the task. Newly written code should NEVER need this option but do compat-independent messages instead! menu "Networking options" source "net/packet/Kconfig" source "net/unix/Kconfig" source "net/xfrm/Kconfig" source "net/iucv/Kconfig" config INET bool "TCP/IP networking" select CRYPTO select CRYPTO_AES ---help--- These are the protocols used on the Internet and on most local Ethernets. It is highly recommended to say Y here (this will enlarge your kernel by about 400 KB), since some programs (e.g. the X window system) use TCP/IP even if your machine is not connected to any other computer. You will get the so-called loopback device which allows you to ping yourself (great fun, that!). For an excellent introduction to Linux networking, please read the Linux Networking HOWTO, available from <http://www.tldp.org/docs.html#howto>. If you say Y here and also to "/proc file system support" and "Sysctl support" below, you can change various aspects of the behavior of the TCP/IP code by writing to the (virtual) files in /proc/sys/net/ipv4/*; the options are explained in the file <file:Documentation/networking/ip-sysctl.txt>. Short answer: say Y. if INET source "net/ipv4/Kconfig" source "net/ipv6/Kconfig" source "net/netlabel/Kconfig" endif # if INET config NETWORK_SECMARK bool "Security Marking" help This enables security marking of network packets, similar to nfmark, but designated for security purposes. If you are unsure how to answer this question, answer N. config NETWORK_PHY_TIMESTAMPING bool "Timestamping in PHY devices" help This allows timestamping of network packets by PHYs with hardware timestamping capabilities. This option adds some overhead in the transmit and receive paths. If you are unsure how to answer this question, answer N. menuconfig NETFILTER bool "Network packet filtering framework (Netfilter)" ---help--- Netfilter is a framework for filtering and mangling network packets that pass through your Linux box. The most common use of packet filtering is to run your Linux box as a firewall protecting a local network from the Internet. The type of firewall provided by this kernel support is called a "packet filter", which means that it can reject individual network packets based on type, source, destination etc. The other kind of firewall, a "proxy-based" one, is more secure but more intrusive and more bothersome to set up; it inspects the network traffic much more closely, modifies it and has knowledge about the higher level protocols, which a packet filter lacks. Moreover, proxy-based firewalls often require changes to the programs running on the local clients. Proxy-based firewalls don't need support by the kernel, but they are often combined with a packet filter, which only works if you say Y here. You should also say Y here if you intend to use your Linux box as the gateway to the Internet for a local network of machines without globally valid IP addresses. This is called "masquerading": if one of the computers on your local network wants to send something to the outside, your box can "masquerade" as that computer, i.e. it forwards the traffic to the intended outside destination, but modifies the packets to make it look like they came from the firewall box itself. It works both ways: if the outside host replies, the Linux box will silently forward the traffic to the correct local computer. This way, the computers on your local net are completely invisible to the outside world, even though they can reach the outside and can receive replies. It is even possible to run globally visible servers from within a masqueraded local network using a mechanism called portforwarding. Masquerading is also often called NAT (Network Address Translation). Another use of Netfilter is in transparent proxying: if a machine on the local network tries to connect to an outside host, your Linux box can transparently forward the traffic to a local server, typically a caching proxy server. Yet another use of Netfilter is building a bridging firewall. Using a bridge with Network packet filtering enabled makes iptables "see" the bridged traffic. For filtering on the lower network and Ethernet protocols over the bridge, use ebtables (under bridge netfilter configuration). Various modules exist for netfilter which replace the previous masquerading (ipmasqadm), packet filtering (ipchains), transparent proxying, and portforwarding mechanisms. Please see <file:Documentation/Changes> under "iptables" for the location of these packages. if NETFILTER config NETFILTER_DEBUG bool "Network packet filtering debugging" depends on NETFILTER help You can say Y here if you want to get additional messages useful in debugging the netfilter code. config NETFILTER_ADVANCED bool "Advanced netfilter configuration" depends on NETFILTER default y help If you say Y here you can select between all the netfilter modules. If you say N the more unusual ones will not be shown and the basic ones needed by most people will default to 'M'. If unsure, say Y. config BRIDGE_NETFILTER bool "Bridged IP/ARP packets filtering" depends on BRIDGE && NETFILTER && INET depends on NETFILTER_ADVANCED default y ---help--- Enabling this option will let arptables resp. iptables see bridged ARP resp. IP traffic. If you want a bridging firewall, you probably want this option enabled. Enabling or disabling this option doesn't enable or disable ebtables. If unsure, say N. source "net/netfilter/Kconfig" source "net/ipv4/netfilter/Kconfig" source "net/ipv6/netfilter/Kconfig" source "net/decnet/netfilter/Kconfig" source "net/bridge/netfilter/Kconfig" endif source "net/dccp/Kconfig" source "net/sctp/Kconfig" source "net/rds/Kconfig" source "net/tipc/Kconfig" source "net/atm/Kconfig" source "net/l2tp/Kconfig" source "net/802/Kconfig" source "net/bridge/Kconfig" source "net/dsa/Kconfig" source "net/8021q/Kconfig" source "net/decnet/Kconfig" source "net/llc/Kconfig" source "net/ipx/Kconfig" source "drivers/net/appletalk/Kconfig" source "net/x25/Kconfig" source "net/lapb/Kconfig" source "net/phonet/Kconfig" source "net/ieee802154/Kconfig" source "net/mac802154/Kconfig" source "net/sched/Kconfig" source "net/dcb/Kconfig" source "net/dns_resolver/Kconfig" source "net/batman-adv/Kconfig" source "net/openvswitch/Kconfig" source "net/vmw_vsock/Kconfig" source "net/netlink/Kconfig" source "net/mpls/Kconfig" config RPS boolean depends on SMP && SYSFS && USE_GENERIC_SMP_HELPERS default y config RFS_ACCEL boolean depends on RPS select CPU_RMAP default y config XPS boolean depends on SMP && USE_GENERIC_SMP_HELPERS default y config NETPRIO_CGROUP tristate "Network priority cgroup" depends on CGROUPS ---help--- Cgroup subsystem for use in assigning processes to network priorities on a per-interface basis config NET_RX_BUSY_POLL boolean default y config BQL boolean depends on SYSFS select DQL default y config BPF_JIT bool "enable BPF Just In Time compiler" depends on HAVE_BPF_JIT depends on MODULES ---help--- Berkeley Packet Filter filtering capabilities are normally handled by an interpreter. This option allows kernel to generate a native code when filter is loaded in memory. This should speedup packet sniffing (libpcap/tcpdump). Note : Admin should enable this feature changing /proc/sys/net/core/bpf_jit_enable config NET_FLOW_LIMIT boolean depends on RPS default y ---help--- The network stack has to drop packets when a receive processing CPU's backlog reaches netdev_max_backlog. If a few out of many active flows generate the vast majority of load, drop their traffic earlier to maintain capacity for the other flows. This feature provides servers with many clients some protection against DoS by a single (spoofed) flow that greatly exceeds average workload. menu "Network testing" config NET_PKTGEN tristate "Packet Generator (USE WITH CAUTION)" depends on INET && PROC_FS ---help--- This module will inject preconfigured packets, at a configurable rate, out of a given interface. It is used for network interface stress testing and performance analysis. If you don't understand what was just said, you don't need it: say N. Documentation on how to use the packet generator can be found at <file:Documentation/networking/pktgen.txt>. To compile this code as a module, choose M here: the module will be called pktgen. config NET_TCPPROBE tristate "TCP connection probing" depends on INET && PROC_FS && KPROBES ---help--- This module allows for capturing the changes to TCP connection state in response to incoming packets. It is used for debugging TCP congestion avoidance modules. If you don't understand what was just said, you don't need it: say N. Documentation on how to use TCP connection probing can be found at: http://www.linuxfoundation.org/collaborate/workgroups/networking/tcpprobe To compile this code as a module, choose M here: the module will be called tcp_probe. config NET_DROP_MONITOR tristate "Network packet drop alerting service" depends on INET && TRACEPOINTS ---help--- This feature provides an alerting service to userspace in the event that packets are discarded in the network stack. Alerts are broadcast via netlink socket to any listening user space process. If you don't need network drop alerts, or if you are ok just checking the various proc files and other utilities for drop statistics, say N here. endmenu endmenu source "net/ax25/Kconfig" source "net/can/Kconfig" source "net/irda/Kconfig" source "net/bluetooth/Kconfig" source "net/rxrpc/Kconfig" config FIB_RULES bool menuconfig WIRELESS bool "Wireless" depends on !S390 default y if WIRELESS source "net/wireless/Kconfig" source "net/mac80211/Kconfig" endif # WIRELESS source "net/wimax/Kconfig" source "net/rfkill/Kconfig" source "net/9p/Kconfig" source "net/caif/Kconfig" source "net/ceph/Kconfig" source "net/nfc/Kconfig" endif # if NET # Used by archs to tell that they support BPF_JIT config HAVE_BPF_JIT bool