1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
|
NVIDIA Tegra Power Management Controller (PMC)
The PMC block interacts with an external Power Management Unit. The PMC
mostly controls the entry and exit of the system from different sleep
modes. It provides power-gating controllers for SoC and CPU power-islands.
Required properties:
- name : Should be pmc
- compatible : For Tegra20, must contain "nvidia,tegra20-pmc". For Tegra30,
must contain "nvidia,tegra30-pmc". For Tegra114, must contain
"nvidia,tegra114-pmc". For Tegra124, must contain "nvidia,tegra124-pmc".
Otherwise, must contain "nvidia,<chip>-pmc", plus at least one of the
above, where <chip> is tegra132.
- reg : Offset and length of the register set for the device
- clocks : Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names : Must include the following entries:
"pclk" (The Tegra clock of that name),
"clk32k_in" (The 32KHz clock input to Tegra).
Optional properties:
- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal.
The PMU is an external Power Management Unit, whose interrupt output
signal is fed into the PMC. This signal is optionally inverted, and then
fed into the ARM GIC. The PMC is not involved in the detection or
handling of this interrupt signal, merely its inversion.
- nvidia,suspend-mode : The suspend mode that the platform should use.
Valid values are 0, 1 and 2:
0 (LP0): CPU + Core voltage off and DRAM in self-refresh
1 (LP1): CPU voltage off and DRAM in self-refresh
2 (LP2): CPU voltage off
- nvidia,core-power-req-active-high : Boolean, core power request active-high
- nvidia,sys-clock-req-active-high : Boolean, system clock request active-high
- nvidia,combined-power-req : Boolean, combined power request for CPU & Core
- nvidia,cpu-pwr-good-en : Boolean, CPU power good signal (from PMIC to PMC)
is enabled.
Required properties when nvidia,suspend-mode is specified:
- nvidia,cpu-pwr-good-time : CPU power good time in uS.
- nvidia,cpu-pwr-off-time : CPU power off time in uS.
- nvidia,core-pwr-good-time : <Oscillator-stable-time Power-stable-time>
Core power good time in uS.
- nvidia,core-pwr-off-time : Core power off time in uS.
Required properties when nvidia,suspend-mode=<0>:
- nvidia,lp0-vec : <start length> Starting address and length of LP0 vector
The LP0 vector contains the warm boot code that is executed by AVP when
resuming from the LP0 state. The AVP (Audio-Video Processor) is an ARM7
processor and always being the first boot processor when chip is power on
or resume from deep sleep mode. When the system is resumed from the deep
sleep mode, the warm boot code will restore some PLLs, clocks and then
bring up CPU0 for resuming the system.
Example:
/ SoC dts including file
pmc@7000f400 {
compatible = "nvidia,tegra20-pmc";
reg = <0x7000e400 0x400>;
clocks = <&tegra_car 110>, <&clk32k_in>;
clock-names = "pclk", "clk32k_in";
nvidia,invert-interrupt;
nvidia,suspend-mode = <1>;
nvidia,cpu-pwr-good-time = <2000>;
nvidia,cpu-pwr-off-time = <100>;
nvidia,core-pwr-good-time = <3845 3845>;
nvidia,core-pwr-off-time = <458>;
nvidia,core-power-req-active-high;
nvidia,sys-clock-req-active-high;
nvidia,lp0-vec = <0xbdffd000 0x2000>;
};
/ Tegra board dts file
{
...
clocks {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
clk32k_in: clock {
compatible = "fixed-clock";
reg=<0>;
#clock-cells = <0>;
clock-frequency = <32768>;
};
};
...
};
|
