summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
blob: 278de8e64bbf591b2b9fe4350fb843679b2cdc8c (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
* Samsung's I2C controller

The Samsung's I2C controller is used to interface with I2C devices.

Required properties:
  - compatible: value should be either of the following.
      (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
      (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
      (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
          inside HDMIPHY block found on several samsung SoCs
      (d) "samsung, exynos5440-i2c", for s3c2440-like i2c used
	   on EXYNOS5440 which does not need GPIO configuration.
      (e) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
	   a host to SATA PHY controller on an internal bus.
  - reg: physical base address of the controller and length of memory mapped
    region.
  - interrupts: interrupt number to the cpu.
  - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.

Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
  - Samsung GPIO variant (deprecated):
    - gpios: The order of the gpios should be the following: <SDA, SCL>.
      The gpio specifier depends on the gpio controller. Required in all
      cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
      lines are permanently wired to the respective clienta
  - Pinctrl variant (preferred, if available):
    - pinctrl-0: Pin control group to be used for this controller.
    - pinctrl-names: Should contain only one value - "default".

Optional properties:
  - samsung,i2c-slave-addr: Slave address in multi-master environment. If not
    specified, default value is 0.
  - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
    specified, the default value in Hz is 100000.

Example:

	i2c@13870000 {
		compatible = "samsung,s3c2440-i2c";
		reg = <0x13870000 0x100>;
		interrupts = <345>;
		samsung,i2c-sda-delay = <100>;
		samsung,i2c-max-bus-freq = <100000>;
		/* Samsung GPIO variant begins here */
		gpios = <&gpd1 2 0 /* SDA */
			 &gpd1 3 0 /* SCL */>;
		/* Samsung GPIO variant ends here */
		/* Pinctrl variant begins here */
		pinctrl-0 = <&i2c3_bus>;
		pinctrl-names = "default";
		/* Pinctrl variant ends here */
		#address-cells = <1>;
		#size-cells = <0>;

		wm8994@1a {
			compatible = "wlf,wm8994";
			reg = <0x1a>;
		};
	};