1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
|
NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver.
Required properties:
- compatible : should be:
"nvidia,tegra114-i2c"
"nvidia,tegra30-i2c"
"nvidia,tegra20-i2c"
"nvidia,tegra20-i2c-dvc"
Details of compatible are as follows:
nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C
controller. This only support master mode of I2C communication. Register
interface/offset and interrupts handling are different than generic I2C
controller. Driver of DVC I2C controller is only compatible with
"nvidia,tegra20-i2c-dvc".
nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support
master and slave mode of I2C communication. The i2c-tegra driver only
support master mode of I2C communication. Driver of I2C controller is
only compatible with "nvidia,tegra20-i2c".
nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is
very much similar to Tegra20 I2C controller with additional feature:
Continue Transfer Support. This feature helps to implement M_NO_START
as per I2C core API transfer flags. Driver of I2C controller is
compatible with "nvidia,tegra30-i2c" to enable the continue transfer
support. This is also compatible with "nvidia,tegra20-i2c" without
continue transfer support.
nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is
very much similar to Tegra30 I2C controller with some hardware
modification:
- Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and
fast-clk. Tegra114 has only one clock source called as div-clk and
hence clock mechanism is changed in I2C controller.
- Tegra30/Tegra20 I2C controller has enabled per packet transfer by
default and there is no way to disable it. Tegra114 has this
interrupt disable by default and SW need to enable explicitly.
Due to above changes, Tegra114 I2C driver makes incompatible with
previous hardware driver. Hence, tegra114 I2C controller is compatible
with "nvidia,tegra114-i2c".
- reg: Should contain I2C controller registers physical address and length.
- interrupts: Should contain I2C controller interrupts.
- address-cells: Address cells for I2C device address.
- size-cells: Size of the I2C device address.
- clocks: Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names: Must include the following entries:
Tegra20/Tegra30:
- div-clk
- fast-clk
Tegra114:
- div-clk
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- i2c
- dmas: Must contain an entry for each entry in clock-names.
See ../dma/dma.txt for details.
- dma-names: Must include the following entries:
- rx
- tx
Example:
i2c@7000c000 {
compatible = "nvidia,tegra20-i2c";
reg = <0x7000c000 0x100>;
interrupts = <0 38 0x04>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&tegra_car 12>, <&tegra_car 124>;
clock-names = "div-clk", "fast-clk";
resets = <&tegra_car 12>;
reset-names = "i2c";
dmas = <&apbdma 16>, <&apbdma 16>;
dma-names = "rx", "tx";
status = "disabled";
};
|
