summaryrefslogtreecommitdiffstats
path: root/Documentation/power/devices.txt
blob: 10018d19e0bfc580a3b383c9fd47cd29db029e8e (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
Device Power Management

(C) 2010 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc.

Most of the code in Linux is device drivers, so most of the Linux power
management code is also driver-specific.  Most drivers will do very little;
others, especially for platforms with small batteries (like cell phones),
will do a lot.

This writeup gives an overview of how drivers interact with system-wide
power management goals, emphasizing the models and interfaces that are
shared by everything that hooks up to the driver model core.  Read it as
background for the domain-specific work you'd do with any specific driver.


Two Models for Device Power Management
======================================
Drivers will use one or both of these models to put devices into low-power
states:

    System Sleep model:
	Drivers can enter low power states as part of entering system-wide
	low-power states like "suspend-to-ram", or (mostly for systems with
	disks) "hibernate" (suspend-to-disk).

	This is something that device, bus, and class drivers collaborate on
	by implementing various role-specific suspend and resume methods to
	cleanly power down hardware and software subsystems, then reactivate
	them without loss of data.

	Some drivers can manage hardware wakeup events, which make the system
	leave that low-power state.  This feature may be enabled or disabled
	using the relevant /sys/devices/.../power/wakeup file (for Ethernet
	drivers the ioctl interface used by ethtool may also be used for this
	purpose); enabling it may cost some power usage, but let the whole
	system enter low power states more often.

    Runtime Power Management model:
	Devices may also be put into low power states while the system is
	running, independently of other power management activity in principle.
	However, devices are not generally independent of each other (for
	example, parent device cannot be suspended unless all of its child
	devices have been suspended).  Moreover,  depending on the bus type the
	device is on, it may be necessary to carry out some bus-specific
	operations on the device for this purpose.  Also, devices put into low
	power states at run time may require special handling during system-wide
	power transitions, like suspend to RAM.

	For these reasons not only the device driver itself, but also the
	appropriate subsystem (bus type, device type or device class) driver
	and the PM core are involved in the runtime power management of devices.
	Like in the system sleep power management case, they need to collaborate
	by implementing various role-specific suspend and resume methods, so
	that the hardware is cleanly powered down and reactivated without data
	or service loss.

There's not a lot to be said about those low power states except that they
are very system-specific, and often device-specific.  Also, that if enough
devices have been put into low power states (at "run time"), the effect may be
very similar to entering some system-wide low-power state (system sleep) ... and
that synergies exist, so that several drivers using runtime PM might put the
system into a state where even deeper power saving options are available.

Most suspended devices will have quiesced all I/O:  no more DMA or IRQs, no
more data read or written, and requests from upstream drivers are no longer
accepted.  A given bus or platform may have different requirements though.

Examples of hardware wakeup events include an alarm from a real time clock,
network wake-on-LAN packets, keyboard or mouse activity, and media insertion
or removal (for PCMCIA, MMC/SD, USB, and so on).


Interfaces for Entering System Sleep States
===========================================
There are programming interfaces provided for subsystem (bus type, device type,
device class) and device drivers in order to allow them to participate in the
power management of devices they are concerned with.  They cover the system
sleep power management as well as the runtime power management of devices.


Device Power Management Operations
----------------------------------
Device power management operations, at the subsystem level as well as at the
device driver level, are implemented by defining and populating objects of type
struct dev_pm_ops:

struct dev_pm_ops {
	int (*prepare)(struct device *dev);
	void (*complete)(struct device *dev);
	int (*suspend)(struct device *dev);
	int (*resume)(struct device *dev);
	int (*freeze)(struct device *dev);
	int (*thaw)(struct device *dev);
	int (*poweroff)(struct device *dev);
	int (*restore)(struct device *dev);
	int (*suspend_noirq)(struct device *dev);
	int (*resume_noirq)(struct device *dev);
	int (*freeze_noirq)(struct device *dev);
	int (*thaw_noirq)(struct device *dev);
	int (*poweroff_noirq)(struct device *dev);
	int (*restore_noirq)(struct device *dev);
	int (*runtime_suspend)(struct device *dev);
	int (*runtime_resume)(struct device *dev);
	int (*runtime_idle)(struct device *dev);
};

This structure is defined in include/linux/pm.h and the methods included in it
are also described in that file.  Their roles will be explained in what follows.
For now, it should be sufficient to remember that the last three of them are
specific to runtime power management, while the remaining ones are used during
system-wide power transitions.

There also is an "old" or "legacy", deprecated way of implementing power
management operations available at least for some subsystems.  This approach
does not use struct dev_pm_ops objects and it only is suitable for implementing
system sleep power management methods.  Therefore it is not described in this
document, so please refer directly to the source code for more information about
it.


Subsystem-Level Methods
-----------------------
The core methods to suspend and resume devices reside in struct dev_pm_ops
pointed to by the pm member of struct bus_type, struct device_type and
struct class.  They are mostly of interest to the people writing infrastructure
for buses, like PCI or USB, or device type and device class drivers.

Bus drivers implement these methods as appropriate for the hardware and
the drivers using it; PCI works differently from USB, and so on.  Not many
people write subsystem-level drivers; most driver code is a "device driver" that
builds on top of bus-specific framework code.

For more information on these driver calls, see the description later;
they are called in phases for every device, respecting the parent-child
sequencing in the driver model tree.


/sys/devices/.../power/wakeup files
-----------------------------------
All devices in the driver model have two flags to control handling of
wakeup events, which are hardware signals that can force the device and/or
system out of a low power state.  These are initialized by bus or device
driver code using device_init_wakeup().

The "can_wakeup" flag just records whether the device (and its driver) can
physically support wakeup events.  When that flag is clear, the sysfs
"wakeup" file is empty, and device_may_wakeup() returns false.

For devices that can issue wakeup events, a separate flag controls whether
that device should try to use its wakeup mechanism.  The initial value of
device_may_wakeup() will be false for the majority of devices, except for
power buttons, keyboards, and Ethernet adapters whose WoL (wake-on-LAN) feature
has been set up with ethtool.  Thus in the majority of cases the device's
"wakeup" file will initially hold the value "disabled".  Userspace can change
that to "enabled", so that device_may_wakeup() returns true, or change it back
to "disabled", so that it returns false again.


/sys/devices/.../power/control files
------------------------------------
All devices in the driver model have a flag to control the desired behavior of
its driver with respect to runtime power management.  This flag, called
runtime_auto, is initialized by the bus type (or generally subsystem) code using
pm_runtime_allow() or pm_runtime_forbid(), depending on whether or not the
driver is supposed to power manage the device at run time by default,
respectively.

This setting may be adjusted by user space by writing either "on" or "auto" to
the device's "control" file.  If "auto" is written, the device's runtime_auto
flag will be set and the driver will be allowed to power manage the device if
capable of doing that.  If "on" is written, the driver is not allowed to power
manage the device which in turn is supposed to remain in the full power state at
run time.  User space can check the current value of the runtime_auto flag by
reading from the device's "control" file.

The device's runtime_auto flag has no effect on the handling of system-wide
power transitions by its driver.  In particular, the device can (and in the
majority of cases should and will) be put into a low power state during a
system-wide transition to a sleep state (like "suspend-to-RAM") even though its
runtime_auto flag is unset (in which case its "control" file contains "on").

For more information about the runtime power management framework for devices
refer to Documentation/power/runtime_pm.txt.


Calling Drivers to Enter System Sleep States
============================================
When the system goes into a sleep state, each device's driver is asked
to suspend the device by putting it into state compatible with the target
system state.  That's usually some version of "off", but the details are
system-specific.  Also, wakeup-enabled devices will usually stay partly
functional in order to wake the system.

When the system leaves that low power state, the device's driver is asked
to resume it.  The suspend and resume operations always go together, and
both are multi-phase operations.

For simple drivers, suspend might quiesce the device using the class code
and then turn its hardware as "off" as possible with late_suspend.  The
matching resume calls would then completely reinitialize the hardware
before reactivating its class I/O queues.

More power-aware drivers might prepare the devices for triggering system wakeup
events.


Call Sequence Guarantees
------------------------
To ensure that bridges and similar links needing to talk to a device are
available when the device is suspended or resumed, the device tree is
walked in a bottom-up order to suspend devices.  A top-down order is
used to resume those devices.

The ordering of the device tree is defined by the order in which devices
get registered:  a child can never be registered, probed or resumed before
its parent; and can't be removed or suspended after that parent.

The policy is that the device tree should match hardware bus topology.
(Or at least the control bus, for devices which use multiple busses.)
In particular, this means that a device registration may fail if the parent of
the device is suspending (i.e. has been chosen by the PM core as the next
device to suspend) or has already suspended, as well as after all of the other
devices have been suspended.  Device drivers must be prepared to cope with such
situations.


Suspending Devices
------------------
Suspending a given device is done in several phases.  Suspending the
system always includes every phase, executing calls for every device
before the next phase begins.  Not all busses or classes support all
these callbacks; and not all drivers use all the callbacks.

Generally, different callbacks are used depending on whether the system is
going to the standby or memory sleep state ("suspend-to-RAM") or it is going to
be hibernated ("suspend-to-disk").

If the system goes to the standby or memory sleep state the phases are seen by
driver notifications issued in this order:

   1	bus->pm.prepare(dev) is called after tasks are frozen and it is supposed
	to call the device driver's ->pm.prepare() method.

	The purpose of this method is mainly to prevent new children of the
	device from being registered after it has returned.  It also may be used
	to generally prepare the device for the upcoming system transition, but
	it should not put the device into a low power state.

   2	class->pm.suspend(dev) is called if dev is associated with a class that
	has such a method.  It may invoke the device driver's ->pm.suspend()
	method, unless type->pm.suspend(dev) or bus->pm.suspend() does that.

   3	type->pm.suspend(dev) is called if dev is associated with a device type
	that has such a method.  It may invoke the device driver's
	->pm.suspend() method, unless class->pm.suspend(dev) or
	bus->pm.suspend() does that.

   4	bus->pm.suspend(dev) is called, if implemented.  It usually calls the
	device driver's ->pm.suspend() method.

	This call should generally quiesce the device so that it doesn't do any
	I/O after the call has returned.  It also may save the device registers
	and put it into the appropriate low power state, depending on the bus
	type the device is on.

   5	bus->pm.suspend_noirq(dev) is called, if implemented.  It may call the
	device driver's ->pm.suspend_noirq() method, depending on the bus type
	in question.

	This method is invoked after device interrupts have been suspended,
	which means that the driver's interrupt handler will not be called
	while it is running.  It should save the values of the device's
	registers that weren't saved previously and finally put the device into
	the appropriate low power state.

	The majority of subsystems and device drivers need not implement this
	method.  However, bus types allowing devices to share interrupt vectors,
	like PCI, generally need to use it to prevent interrupt handling issues
	from happening during suspend.

At the end of those phases, drivers should normally have stopped all I/O
transactions (DMA, IRQs), saved enough state that they can re-initialize
or restore previous state (as needed by the hardware), and placed the
device into a low-power state.  On many platforms they will also use
gate off one or more clock sources; sometimes they will also switch off power
supplies, or reduce voltages.  [Drivers supporting runtime PM may already have
performed some or all of the steps needed to prepare for the upcoming system
state transition.]

If device_may_wakeup(dev) returns true, the device should be prepared for
generating hardware wakeup signals when the system is in the sleep state to
trigger a system wakeup event.  For example, enable_irq_wake() might identify
GPIO signals hooked up to a switch or other external hardware, and
pci_enable_wake() does something similar for the PCI PME signal.

If a driver (or subsystem) fails it suspend method, the system won't enter the
desired low power state; it will resume all the devices it's suspended so far.


Hibernation Phases
------------------
Hibernating the system is more complicated than putting it into the standby or
memory sleep state, because it involves creating a system image and saving it.
Therefore there are more phases of hibernation and special device PM methods are
used in this case.

First, it is necessary to prepare the system for creating a hibernation image.
This is similar to putting the system into the standby or memory sleep state,
although it generally doesn't require that devices be put into low power states
(that is even not desirable at this point).  Driver notifications are then
issued in the following order:

   1	bus->pm.prepare(dev) is called after tasks have been frozen and enough
	memory has been freed.

   2	class->pm.freeze(dev) is called if implemented.  It may invoke the
        device driver's ->pm.freeze() method, unless type->pm.freeze(dev) or
        bus->pm.freeze() does that.

   3	type->pm.freeze(dev) is called if implemented.  It may invoke the device
	driver's ->pm.suspend() method, unless class->pm.freeze(dev) or
	bus->pm.freeze() does that.

   4	bus->pm.freeze(dev) is called, if implemented.  It usually calls the
	device driver's ->pm.freeze() method.

   5	bus->pm.freeze_noirq(dev) is called, if implemented.  It may call the
	device driver's ->pm.freeze_noirq() method, depending on the bus type
	in question.

The difference between ->pm.freeze() and the corresponding ->pm.suspend() (and
similarly for the "noirq" variants) is that the former should avoid preparing
devices to trigger system wakeup events and putting devices into low power
states, although they generally have to save the values of device registers
so that it's possible to restore them during system resume.

Second, after the system image has been created, the functionality of devices
has to be restored so that the image can be saved.  That is similar to resuming
devices after the system has been woken up from the standby or memory sleep
state, which is described below, and causes the following device notifications
to be issued:

   1	bus->pm.thaw_noirq(dev), if implemented; may call the device driver's
	->pm.thaw_noirq() method, depending on the bus type in question.

   2	bus->pm.thaw(dev), if implemented; usually calls the device driver's
	->pm.thaw() method.

   3	type->pm.thaw(dev), if implemented; may call the device driver's
	->pm.thaw() method if not called by the bus type or class.

   4	class->pm.thaw(dev), if implemented; may call the device driver's
	->pm.thaw() method if not called by the bus type or device type.

   5	bus->pm.complete(dev), if implemented; may call the device driver's
	->pm.complete() method.

Generally, the role of the ->pm.thaw() methods (including the "noirq" variants)
is to bring the device back to the fully functional state, so that it may be
used for saving the image, if necessary.  The role of bus->pm.complete() is to
reverse whatever bus->pm.prepare() did (likewise for the analogous device driver
callbacks).

After the image has been saved, the devices need to be prepared for putting the
system into the low power state.  That is analogous to suspending them before
putting the system into the standby or memory sleep state and involves the
following device notifications:

   1	bus->pm.prepare(dev).

   2	class->pm.poweroff(dev), if implemented; may invoke the device driver's
   	->pm.poweroff() method if not called by the bus type or device type.

   3	type->pm.poweroff(dev), if implemented; may invoke the device driver's
   	->pm.poweroff() method if not called by the bus type or device class.

   4	bus->pm.poweroff(dev), if implemented; usually calls the device driver's
   	->pm.poweroff() method (if not called by the device class or type).

   5	bus->pm.poweroff_noirq(dev), if implemented; may call the device
	driver's ->pm.poweroff_noirq() method, depending on the bus type
	in question.

The difference between ->pm.poweroff() and the corresponding ->pm.suspend() (and
analogously for the "noirq" variants) is that the former need not save the
device's registers.  Still, they should prepare the device for triggering
system wakeup events if necessary and finally put it into the appropriate low
power state.


Device Low Power (suspend) States
---------------------------------
Device low-power states aren't standard.  One device might only handle
"on" and "off, while another might support a dozen different versions of
"on" (how many engines are active?), plus a state that gets back to "on"
faster than from a full "off".

Some busses define rules about what different suspend states mean.  PCI
gives one example:  after the suspend sequence completes, a non-legacy
PCI device may not perform DMA or issue IRQs, and any wakeup events it
issues would be issued through the PME# bus signal.  Plus, there are
several PCI-standard device states, some of which are optional.

In contrast, integrated system-on-chip processors often use IRQs as the
wakeup event sources (so drivers would call enable_irq_wake) and might
be able to treat DMA completion as a wakeup event (sometimes DMA can stay
active too, it'd only be the CPU and some peripherals that sleep).

Some details here may be platform-specific.  Systems may have devices that
can be fully active in certain sleep states, such as an LCD display that's
refreshed using DMA while most of the system is sleeping lightly ... and
its frame buffer might even be updated by a DSP or other non-Linux CPU while
the Linux control processor stays idle.

Moreover, the specific actions taken may depend on the target system state.
One target system state might allow a given device to be very operational;
another might require a hard shut down with re-initialization on resume.
And two different target systems might use the same device in different
ways; the aforementioned LCD might be active in one product's "standby",
but a different product using the same SOC might work differently.


Resuming Devices
----------------
Resuming is done in multiple phases, much like suspending, with all
devices processing each phase's calls before the next phase begins.

Again, however, different callbacks are used depending on whether the system is
waking up from the standby or memory sleep state ("suspend-to-RAM") or from
hibernation ("suspend-to-disk").

If the system is waking up from the standby or memory sleep state, the phases
are seen by driver notifications issued in this order:

   1	bus->pm.resume_noirq(dev) is called, if implemented.  It may call the
	device driver's ->pm.resume_noirq() method, depending on the bus type in
	question.

	The role of this method is to perform actions that need to be performed
	before device drivers' interrupt handlers are allowed to be invoked.  If
	the given bus type permits devices to share interrupt vectors, like PCI,
	this method should bring the device and its driver into a state in which
	the driver can recognize if the device is the source of incoming
	interrupts, if any, and handle them correctly.

	For example, the PCI bus type's ->pm.resume_noirq() puts the device into
	the full power state (D0 in the PCI terminology) and restores the
	standard configuration registers of the device.  Then, it calls the
	device driver's ->pm.resume_noirq() method to perform device-specific
	actions needed at this stage of resume.

   2	bus->pm.resume(dev) is called, if implemented.  It usually calls the
	device driver's ->pm.resume() method.

	This call should generally bring the the device back to the working
	state, so that it can do I/O as requested after the call has returned.
	However, it may be more convenient to use the device class or device
	type ->pm.resume() for this purpose, in which case the bus type's
	->pm.resume() method need not be implemented at all.

   3	type->pm.resume(dev) is called, if implemented.  It may invoke the
	device driver's ->pm.resume() method, unless class->pm.resume(dev) or
	bus->pm.resume() does that.

	For devices that are not associated with any bus type or device class
	this method plays the role of bus->pm.resume().

   4	class->pm.resume(dev) is called, if implemented.  It may invoke the
	device driver's ->pm.resume() method, unless bus->pm.resume(dev) or
	type->pm.resume() does that.

	For devices that are not associated with any bus type or device type
	this method plays the role of bus->pm.resume().

   5	bus->pm.complete(dev) is called, if implemented.  It is supposed to
	invoke the device driver's ->pm.complete() method.

	The role of this method is to reverse whatever bus->pm.prepare(dev)
	(or the driver's ->pm.prepare()) did during suspend, if necessary.

At the end of those phases, drivers should normally be as functional as
they were before suspending:  I/O can be performed using DMA and IRQs, and
the relevant clocks are gated on.  In principle the device need not be
"fully on"; it might be in a runtime lowpower/suspend state during suspend and
the resume callbacks may try to restore that state, but that need not be
desirable from the user's point of view.  In fact, there are multiple reasons
why it's better to always put devices into the "fully working" state in the
system sleep resume callbacks and they are discussed in more detail in
Documentation/power/runtime_pm.txt.

However, the details here may again be platform-specific.  For example,
some systems support multiple "run" states, and the mode in effect at
the end of resume might not be the one which preceded suspension.
That means availability of certain clocks or power supplies changed,
which could easily affect how a driver works.

Drivers need to be able to handle hardware which has been reset since the
suspend methods were called, for example by complete reinitialization.
This may be the hardest part, and the one most protected by NDA'd documents
and chip errata.  It's simplest if the hardware state hasn't changed since
the suspend was carried out, but that can't be guaranteed (in fact, it ususally
is not the case).

Drivers must also be prepared to notice that the device has been removed
while the system was powered off, whenever that's physically possible.
PCMCIA, MMC, USB, Firewire, SCSI, and even IDE are common examples of busses
where common Linux platforms will see such removal.  Details of how drivers
will notice and handle such removals are currently bus-specific, and often
involve a separate thread.


Resume From Hibernation
-----------------------
Resuming from hibernation is, again, more complicated than resuming from a sleep
state in which the contents of main memory are preserved, because it requires
a system image to be loaded into memory and the pre-hibernation memory contents
to be restored before control can be passed back to the image kernel.

In principle, the image might be loaded into memory and the pre-hibernation
memory contents might be restored by the boot loader.  For this purpose,
however, the boot loader would need to know the image kernel's entry point and
there's no protocol defined for passing that information to boot loaders.  As
a workaround, the boot loader loads a fresh instance of the kernel, called the
boot kernel, into memory and passes control to it in a usual way.  Then, the
boot kernel reads the hibernation image, restores the pre-hibernation memory
contents and passes control to the image kernel.  Thus, in fact, two different
kernels are involved in resuming from hibernation and in general they are not
only different because they play different roles in this operation.  Actually,
the boot kernel may be completely different from the image kernel.  Not only
the configuration of it, but also the version of it may be different.
The consequences of this are important to device drivers and their subsystems
(bus types, device classes and device types) too.

Namely, to be able to load the hibernation image into memory, the boot kernel
needs to include at least the subset of device drivers allowing it to access the
storage medium containing the image, although it generally doesn't need to
include all of the drivers included into the image kernel.  After the image has
been loaded the devices handled by those drivers need to be prepared for passing
control back to the image kernel.  This is very similar to the preparation of
devices for creating a hibernation image described above.  In fact, it is done
in the same way, with the help of the ->pm.prepare(), ->pm.freeze() and
->pm.freeze_noirq() callbacks, but only for device drivers included in the boot
kernel (whose versions may generally be different from the versions of the
analogous drivers from the image kernel).

Should the restoration of the pre-hibernation memory contents fail, the boot
kernel would carry out the procedure of "thawing" devices described above, using
the ->pm.thaw_noirq(), ->pm.thaw(), and ->pm.complete() callbacks provided by
subsystems and device drivers.  This, however, is a very rare condition.  Most
often the pre-hibernation memory contents are restored successfully and control
is passed to the image kernel that is now responsible for bringing the system
back to the working state.

To achieve this goal, among other things, the image kernel restores the
pre-hibernation functionality of devices.  This operation is analogous to the
resuming of devices after waking up from the memory sleep state, although it
involves different device notifications which are the following:

   1	bus->pm.restore_noirq(dev), if implemented; may call the device driver's
	->pm.restore_noirq() method, depending on the bus type in question.

   2	bus->pm.restore(dev), if implemented; usually calls the device driver's
	->pm.restore() method.

   3	type->pm.restore(dev), if implemented; may call the device driver's
	->pm.restore() method if not called by the bus type or class.

   4	class->pm.restore(dev), if implemented; may call the device driver's
	->pm.restore() method if not called by the bus type or device type.

   5	bus->pm.complete(dev), if implemented; may call the device driver's
	->pm.complete() method.

The roles of the ->pm.restore_noirq() and ->pm.restore() callbacks are analogous
to the roles of the corresponding resume callbacks, but they must assume that
the device may have been accessed before by the boot kernel.  Consequently, the
state of the device before they are called may be different from the state of it
right prior to calling the resume callbacks.  That difference usually doesn't
matter, so the majority of device drivers can set their resume and restore
callback pointers to the same routine.  Nevertheless, different callback
pointers are used in case there is a situation where it actually matters.


System Devices
--------------
System devices follow a slightly different API, which can be found in

	include/linux/sysdev.h
	drivers/base/sys.c

System devices will only be suspended with interrupts disabled, and after
all other devices have been suspended.  On resume, they will be resumed
before any other devices, and also with interrupts disabled.

That is, when the non-boot CPUs are all offline and IRQs are disabled on the
remaining online CPU, then the sysdev_driver.suspend() phase is carried out, and
the system enters a sleep state (or hibernation image is created).  During
resume (or after the image has been created) the sysdev_driver.resume() phase
is carried out, IRQs are enabled on the only online CPU, the non-boot CPUs are
enabled and that is followed by the "early resume" phase (in which the "noirq"
callbacks provided by subsystems and device drivers are invoked).

Code to actually enter and exit the system-wide low power state sometimes
involves hardware details that are only known to the boot firmware, and
may leave a CPU running software (from SRAM or flash memory) that monitors
the system and manages its wakeup sequence.


Power Management Notifiers
--------------------------
As stated in Documentation/power/notifiers.txt, there are some operations that
cannot be carried out by the power management callbacks discussed above, because
carrying them out at these points would be too late or too early.  To handle
these cases subsystems and device drivers may register power management
notifiers that are called before tasks are frozen and after they have been
thawed.

Generally speaking, the PM notifiers are suitable for performing actions that
either require user space to be available, or at least won't interfere with user
space in a wrong way.

For details refer to Documentation/power/notifiers.txt.


Runtime Power Management
========================
Many devices are able to dynamically power down while the system is still
running. This feature is useful for devices that are not being used, and
can offer significant power savings on a running system.  These devices
often support a range of runtime power states, which might use names such
as "off", "sleep", "idle", "active", and so on.  Those states will in some
cases (like PCI) be partially constrained by a bus the device uses, and will
usually include hardware states that are also used in system sleep states.

Note, however, that a system-wide power transition can be started while some
devices are in low power states due to the runtime power management.  The system
sleep PM callbacks should generally recognize such situations and react to them
appropriately, but the recommended actions to be taken in that cases are
subsystem-specific.

In some cases the decision may be made at the subsystem level while in some
other cases the device driver may be left to decide.  In some cases it may be
desirable to leave a suspended device in that state during system-wide power
transition, but in some other cases the device ought to be put back into the
full power state, for example to be configured for system wakeup or so that its
system wakeup capability can be disabled.  That all depends on the hardware
and the design of the subsystem and device driver in question.

During system-wide resume from a sleep state it's better to put devices into
the full power state, as explained in Documentation/power/runtime_pm.txt.  Refer
to that document for more information regarding this particular issue as well as
for information on the device runtime power management framework in general.