1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
|
/*
* linux/arch/arm/mach-at91/board-rm9200ek.c
*
* Copyright (C) 2005 SAN People
*
* Epson S1D framebuffer glue code is:
* Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/mtd/physmap.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include "generic.h"
static void __init ek_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static struct at91_eth_data __initdata ek_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
};
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PD4,
.pullup_pin = AT91_PIN_PD5,
};
#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
static struct at91_mmc_data __initdata ek_mmc_data = {
.det_pin = AT91_PIN_PB27,
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
};
#endif
static struct spi_board_info ek_spi_devices[] = {
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.chip_select = 0,
.max_speed_hz = 15 * 1000 * 1000,
},
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
{ /* DataFlash card */
.modalias = "mtd_dataflash",
.chip_select = 3,
.max_speed_hz = 15 * 1000 * 1000,
},
#endif
};
static struct i2c_board_info __initdata ek_i2c_devices[] = {
{
I2C_BOARD_INFO("ics1523", 0x26),
},
{
I2C_BOARD_INFO("dac3550", 0x4d),
}
};
#define EK_FLASH_BASE AT91_CHIPSELECT_0
#define EK_FLASH_SIZE SZ_2M
static struct physmap_flash_data ek_flash_data = {
.width = 2,
};
static struct resource ek_flash_resource = {
.start = EK_FLASH_BASE,
.end = EK_FLASH_BASE + EK_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device ek_flash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &ek_flash_data,
},
.resource = &ek_flash_resource,
.num_resources = 1,
};
static struct gpio_led ek_leds[] = {
{ /* "user led 1", DS2 */
.name = "green",
.gpio = AT91_PIN_PB0,
.active_low = 1,
.default_trigger = "mmc0",
},
{ /* "user led 2", DS4 */
.name = "yellow",
.gpio = AT91_PIN_PB1,
.active_low = 1,
.default_trigger = "heartbeat",
},
{ /* "user led 3", DS6 */
.name = "red",
.gpio = AT91_PIN_PB2,
.active_low = 1,
}
};
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&ek_eth_data);
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
/* DataFlash card */
at91_set_gpio_output(AT91_PIN_PB22, 0);
#else
/* MMC */
at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
at91_add_device_mmc(0, &ek_mmc_data);
#endif
/* NOR Flash */
platform_device_register(&ek_flash);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* VGA */
// ek_add_device_video();
}
MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
/* Maintainer: SAN People/Atmel */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
MACHINE_END
|
