1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
|
/*
* arch/arm/plat-omap/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for OMAP-based platforms
*
* Copyright (C) 2009 Texas Instruments
* Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <mach/hardware.h>
#include <mach/io.h>
#include <mach/irqs.h>
#include <asm/hardware/gic.h>
#include <plat/omap24xx.h>
#include <plat/omap34xx.h>
/* REVISIT: This should be set dynamically if CONFIG_MULTI_OMAP2 is selected */
#if defined(CONFIG_ARCH_OMAP2420) || defined(CONFIG_ARCH_OMAP2430)
#define OMAP2_VA_IC_BASE OMAP2_L4_IO_ADDRESS(OMAP24XX_IC_BASE)
#elif defined(CONFIG_ARCH_OMAP34XX)
#define OMAP2_VA_IC_BASE OMAP2_L4_IO_ADDRESS(OMAP34XX_IC_BASE)
#endif
#if defined(CONFIG_ARCH_OMAP4)
#include <plat/omap44xx.h>
#endif
#define INTCPS_SIR_IRQ_OFFSET 0x0040 /* Active interrupt offset */
#define ACTIVEIRQ_MASK 0x7f /* Active interrupt bits */
.macro disable_fiq
.endm
.macro get_irqnr_preamble, base, tmp
.endm
.macro arch_ret_to_user, tmp1, tmp2
.endm
#ifndef CONFIG_ARCH_OMAP4
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \base, =OMAP2_VA_IC_BASE
ldr \irqnr, [\base, #0x98] /* IRQ pending reg 1 */
cmp \irqnr, #0x0
bne 2222f
ldr \irqnr, [\base, #0xb8] /* IRQ pending reg 2 */
cmp \irqnr, #0x0
bne 2222f
ldr \irqnr, [\base, #0xd8] /* IRQ pending reg 3 */
cmp \irqnr, #0x0
2222:
ldrne \irqnr, [\base, #INTCPS_SIR_IRQ_OFFSET]
and \irqnr, \irqnr, #ACTIVEIRQ_MASK /* Clear spurious bits */
.endm
#else
#define OMAP44XX_VA_GIC_CPU_BASE OMAP2_L4_IO_ADDRESS(OMAP44XX_GIC_CPU_BASE)
/*
* The interrupt numbering scheme is defined in the
* interrupt controller spec. To wit:
*
* Interrupts 0-15 are IPI
* 16-28 are reserved
* 29-31 are local. We allow 30 to be used for the watchdog.
* 32-1020 are global
* 1021-1022 are reserved
* 1023 is "spurious" (no interrupt)
*
* For now, we ignore all local interrupts so only return an
* interrupt if it's between 30 and 1020. The test_for_ipi
* routine below will pick up on IPIs.
* A simple read from the controller will tell us the number
* of the highest priority enabled interrupt.
* We then just need to check whether it is in the
* valid range for an IRQ (30-1020 inclusive).
*/
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \base, =OMAP44XX_VA_GIC_CPU_BASE
ldr \irqstat, [\base, #GIC_CPU_INTACK]
ldr \tmp, =1021
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #29
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
.endm
/* We assume that irqstat (the raw value of the IRQ acknowledge
* register) is preserved from the macro above.
* If there is an IPI, we immediately signal end of interrupt
* on the controller, since this requires the original irqstat
* value which we won't easily be able to recreate later.
*/
.macro test_for_ipi, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #16
it cc
strcc \irqstat, [\base, #GIC_CPU_EOI]
it cs
cmpcs \irqnr, \irqnr
.endm
/* As above, this assumes that irqstat and base are preserved */
.macro test_for_ltirq, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
mov \tmp, #0
cmp \irqnr, #29
itt eq
moveq \tmp, #1
streq \irqstat, [\base, #GIC_CPU_EOI]
cmp \tmp, #0
.endm
#endif
.macro irq_prio_table
.endm
|
