1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
|
/* arch/arm/mach-s3c2410/include/mach/gpio-fns.h
*
* Copyright (c) 2003-2009 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - hardware
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __MACH_GPIO_FNS_H
#define __MACH_GPIO_FNS_H __FILE__
/* These functions are in the to-be-removed category and it is strongly
* encouraged not to use these in new code. They will be marked deprecated
* very soon.
*
* Most of the functionality can be either replaced by the gpiocfg calls
* for the s3c platform or by the generic GPIOlib API.
*
* As of 2.6.35-rc, these will be removed, with the few drivers using them
* either replaced or given a wrapper until the calls can be removed.
*/
#include <plat/gpio-cfg.h>
static inline void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int cfg)
{
/* 1:1 mapping between cfgpin and setcfg calls at the moment */
s3c_gpio_cfgpin(pin, cfg);
}
/* external functions for GPIO support
*
* These allow various different clients to access the same GPIO
* registers without conflicting. If your driver only owns the entire
* GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
*/
extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
/* s3c2410_gpio_getirq
*
* turn the given pin number into the corresponding IRQ number
*
* returns:
* < 0 = no interrupt for this pin
* >=0 = interrupt number for the pin
*/
extern int s3c2410_gpio_getirq(unsigned int pin);
#ifdef CONFIG_CPU_S3C2400
extern int s3c2400_gpio_getirq(unsigned int pin);
#endif /* CONFIG_CPU_S3C2400 */
/* s3c2410_gpio_irqfilter
*
* set the irq filtering on the given pin
*
* on = 0 => disable filtering
* 1 => enable filtering
*
* config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with
* width of filter (0 through 63)
*
*
*/
extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
unsigned int config);
/* s3c2410_gpio_pullup
*
* This call should be replaced with s3c_gpio_setpull().
*
* As a note, there is currently no distinction between pull-up and pull-down
* in the s3c24xx series devices with only an on/off configuration.
*/
/* s3c2410_gpio_pullup
*
* configure the pull-up control on the given pin
*
* to = 1 => disable the pull-up
* 0 => enable the pull-up
*
* eg;
*
* s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
* s3c2410_gpio_pullup(S3C2410_GPE(8), 0);
*/
extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
#endif /* __MACH_GPIO_FNS_H */
|
