1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
|
/*
* Copyright (C) 2008-2012 ST-Ericsson
*
* Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2, as
* published by the Free Software Foundation.
*
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/platform_data/db8500_thermal.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
#include <linux/mfd/abx500/ab8500.h>
#include <linux/regulator/ab8500.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/driver.h>
#include <linux/mfd/tps6105x.h>
#include <linux/platform_data/leds-lp55xx.h>
#include <linux/input.h>
#include <linux/delay.h>
#include <linux/leds.h>
#include <linux/pinctrl/consumer.h>
#include <linux/platform_data/pinctrl-nomadik.h>
#include <linux/platform_data/dma-ste-dma40.h>
#include <asm/mach-types.h>
#include "setup.h"
#include "devices.h"
#include "irqs.h"
#include "ste-dma40-db8500.h"
#include "db8500-regs.h"
#include "devices-db8500.h"
#include "board-mop500.h"
#include "board-mop500-regulators.h"
struct ab8500_platform_data ab8500_platdata = {
.irq_base = MOP500_AB8500_IRQ_BASE,
.regulator = &ab8500_regulator_plat_data,
};
#ifdef CONFIG_STE_DMA40
static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = DMA_DEV_TO_MEM,
.dev_type = DB8500_DMA_DEV8_SSP0,
};
static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = DMA_MEM_TO_DEV,
.dev_type = DB8500_DMA_DEV8_SSP0,
};
#endif
struct pl022_ssp_controller ssp0_plat = {
.bus_id = 0,
#ifdef CONFIG_STE_DMA40
.enable_dma = 1,
.dma_filter = stedma40_filter,
.dma_rx_param = &ssp0_dma_cfg_rx,
.dma_tx_param = &ssp0_dma_cfg_tx,
#else
.enable_dma = 0,
#endif
/* on this platform, gpio 31,142,144,214 &
* 224 are connected as chip selects
*/
.num_chipselect = 5,
};
static void __init snowball_init_machine(void)
{
/* This board has full regulator constraints */
regulator_has_full_constraints();
}
static void __init hrefv60_init_machine(void)
{
/* This board has full regulator constraints */
regulator_has_full_constraints();
}
MACHINE_START(HREFV60, "ST-Ericsson U8500 Platform HREFv60+")
.atag_offset = 0x100,
.smp = smp_ops(ux500_smp_ops),
.map_io = u8500_map_io,
.init_irq = ux500_init_irq,
.init_time = ux500_timer_init,
.init_machine = hrefv60_init_machine,
.restart = ux500_restart,
.init_late = NULL,
MACHINE_END
MACHINE_START(SNOWBALL, "Calao Systems Snowball platform")
.atag_offset = 0x100,
.smp = smp_ops(ux500_smp_ops),
.map_io = u8500_map_io,
.init_irq = ux500_init_irq,
/* we re-use nomadik timer here */
.init_time = ux500_timer_init,
.init_machine = snowball_init_machine,
.restart = ux500_restart,
.init_late = NULL,
MACHINE_END
|
