1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
|
/*
* Unmaintained SGI Visual Workstation support.
* Split out from setup.c by davej@suse.de
*/
#include <linux/smp.h>
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <asm/fixmap.h>
#include <asm/arch_hooks.h>
#include <asm/io.h>
#include "cobalt.h"
#include "piix4.h"
int no_broadcast;
char visws_board_type = -1;
char visws_board_rev = -1;
void __init visws_get_board_type_and_rev(void)
{
int raw;
visws_board_type = (char)(inb_p(PIIX_GPI_BD_REG) & PIIX_GPI_BD_REG)
>> PIIX_GPI_BD_SHIFT;
/*
* Get Board rev.
* First, we have to initialize the 307 part to allow us access
* to the GPIO registers. Let's map them at 0x0fc0 which is right
* after the PIIX4 PM section.
*/
outb_p(SIO_DEV_SEL, SIO_INDEX);
outb_p(SIO_GP_DEV, SIO_DATA); /* Talk to GPIO regs. */
outb_p(SIO_DEV_MSB, SIO_INDEX);
outb_p(SIO_GP_MSB, SIO_DATA); /* MSB of GPIO base address */
outb_p(SIO_DEV_LSB, SIO_INDEX);
outb_p(SIO_GP_LSB, SIO_DATA); /* LSB of GPIO base address */
outb_p(SIO_DEV_ENB, SIO_INDEX);
outb_p(1, SIO_DATA); /* Enable GPIO registers. */
/*
* Now, we have to map the power management section to write
* a bit which enables access to the GPIO registers.
* What lunatic came up with this shit?
*/
outb_p(SIO_DEV_SEL, SIO_INDEX);
outb_p(SIO_PM_DEV, SIO_DATA); /* Talk to GPIO regs. */
outb_p(SIO_DEV_MSB, SIO_INDEX);
outb_p(SIO_PM_MSB, SIO_DATA); /* MSB of PM base address */
outb_p(SIO_DEV_LSB, SIO_INDEX);
outb_p(SIO_PM_LSB, SIO_DATA); /* LSB of PM base address */
outb_p(SIO_DEV_ENB, SIO_INDEX);
outb_p(1, SIO_DATA); /* Enable PM registers. */
/*
* Now, write the PM register which enables the GPIO registers.
*/
outb_p(SIO_PM_FER2, SIO_PM_INDEX);
outb_p(SIO_PM_GP_EN, SIO_PM_DATA);
/*
* Now, initialize the GPIO registers.
* We want them all to be inputs which is the
* power on default, so let's leave them alone.
* So, let's just read the board rev!
*/
raw = inb_p(SIO_GP_DATA1);
raw &= 0x7f; /* 7 bits of valid board revision ID. */
if (visws_board_type == VISWS_320) {
if (raw < 0x6) {
visws_board_rev = 4;
} else if (raw < 0xc) {
visws_board_rev = 5;
} else {
visws_board_rev = 6;
}
} else if (visws_board_type == VISWS_540) {
visws_board_rev = 2;
} else {
visws_board_rev = raw;
}
printk(KERN_INFO "Silicon Graphics Visual Workstation %s (rev %d) detected\n",
(visws_board_type == VISWS_320 ? "320" :
(visws_board_type == VISWS_540 ? "540" :
"unknown")), visws_board_rev);
}
void __init pre_intr_init_hook(void)
{
init_VISWS_APIC_irqs();
}
void __init intr_init_hook(void)
{
#ifdef CONFIG_X86_LOCAL_APIC
apic_intr_init();
#endif
}
void __init pre_setup_arch_hook()
{
visws_get_board_type_and_rev();
}
static struct irqaction irq0 = {
.handler = timer_interrupt,
.flags = SA_INTERRUPT,
.name = "timer",
};
void __init time_init_hook(void)
{
printk(KERN_INFO "Starting Cobalt Timer system clock\n");
/* Set the countdown value */
co_cpu_write(CO_CPU_TIMEVAL, CO_TIME_HZ/HZ);
/* Start the timer */
co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) | CO_CTRL_TIMERUN);
/* Enable (unmask) the timer interrupt */
co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) & ~CO_CTRL_TIMEMASK);
/* Wire cpu IDT entry to s/w handler (and Cobalt APIC to IDT) */
setup_irq(0, &irq0);
}
|
