1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
|
/*
*
* BRIEF MODULE DESCRIPTION
* Alchemy Pb1200/Db1200 board setup.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/config.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ioport.h>
#include <linux/mm.h>
#include <linux/console.h>
#include <linux/mc146818rtc.h>
#include <linux/delay.h>
#if defined(CONFIG_BLK_DEV_IDE_AU1XXX)
#include <linux/ide.h>
#endif
#include <asm/cpu.h>
#include <asm/bootinfo.h>
#include <asm/irq.h>
#include <asm/mipsregs.h>
#include <asm/reboot.h>
#include <asm/pgtable.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
#ifdef CONFIG_MIPS_PB1200
#include <asm/mach-pb1x00/pb1200.h>
#endif
#ifdef CONFIG_MIPS_DB1200
#include <asm/mach-db1x00/db1200.h>
#define PB1200_ETH_INT DB1200_ETH_INT
#define PB1200_IDE_INT DB1200_IDE_INT
#endif
extern void _board_init_irq(void);
extern void (*board_init_irq)(void);
void board_reset (void)
{
bcsr->resets = 0;
bcsr->system = 0;
}
void __init board_setup(void)
{
char *argptr = NULL;
u32 pin_func;
#if 0
/* Enable PSC1 SYNC for AC97. Normaly done in audio driver,
* but it is board specific code, so put it here.
*/
pin_func = au_readl(SYS_PINFUNC);
au_sync();
pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
au_writel(pin_func, SYS_PINFUNC);
au_writel(0, (u32)bcsr|0x10); /* turn off pcmcia power */
au_sync();
#endif
#if defined(CONFIG_I2C_AU1550)
{
u32 freq0, clksrc;
/* Select SMBUS in CPLD */
bcsr->resets &= ~(BCSR_RESETS_PCS0MUX);
pin_func = au_readl(SYS_PINFUNC);
au_sync();
pin_func &= ~(3<<17 | 1<<4);
/* Set GPIOs correctly */
pin_func |= 2<<17;
au_writel(pin_func, SYS_PINFUNC);
au_sync();
/* The i2c driver depends on 50Mhz clock */
freq0 = au_readl(SYS_FREQCTRL0);
au_sync();
freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
freq0 |= (3<<SYS_FC_FRDIV1_BIT);
/* 396Mhz / (3+1)*2 == 49.5Mhz */
au_writel(freq0, SYS_FREQCTRL0);
au_sync();
freq0 |= SYS_FC_FE1;
au_writel(freq0, SYS_FREQCTRL0);
au_sync();
clksrc = au_readl(SYS_CLKSRC);
au_sync();
clksrc &= ~0x01f00000;
/* bit 22 is EXTCLK0 for PSC0 */
clksrc |= (0x3 << 22);
au_writel(clksrc, SYS_CLKSRC);
au_sync();
}
#endif
#ifdef CONFIG_FB_AU1200
argptr = prom_getcmdline();
#ifdef CONFIG_MIPS_PB1200
strcat(argptr, " video=au1200fb:panel:bs");
#endif
#ifdef CONFIG_MIPS_DB1200
strcat(argptr, " video=au1200fb:panel:bs");
#endif
#endif
/* The Pb1200 development board uses external MUX for PSC0 to
support SMB/SPI. bcsr->resets bit 12: 0=SMB 1=SPI
*/
#if defined(CONFIG_AU1XXX_PSC_SPI) && defined(CONFIG_I2C_AU1550)
#error I2C and SPI are mutually exclusive. Both are physically connected to PSC0.\
Refer to Pb1200/Db1200 documentation.
#elif defined( CONFIG_AU1XXX_PSC_SPI )
bcsr->resets |= BCSR_RESETS_PCS0MUX;
/*Hard Coding Value to enable Temp Sensors [bit 14] Value for SOC Au1200. Pls refer documentation*/
bcsr->resets =0x900f;
#elif defined( CONFIG_I2C_AU1550 )
bcsr->resets &= (~BCSR_RESETS_PCS0MUX);
#endif
au_sync();
#ifdef CONFIG_MIPS_PB1200
printk("AMD Alchemy Pb1200 Board\n");
#endif
#ifdef CONFIG_MIPS_DB1200
printk("AMD Alchemy Db1200 Board\n");
#endif
/* Setup Pb1200 External Interrupt Controller */
{
extern void (*board_init_irq)(void);
extern void _board_init_irq(void);
board_init_irq = _board_init_irq;
}
}
int
board_au1200fb_panel (void)
{
BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
int p;
p = bcsr->switches;
p >>= 8;
p &= 0x0F;
return p;
}
int
board_au1200fb_panel_init (void)
{
/* Apply power */
BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
bcsr->board |= (BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD | BCSR_BOARD_LCDBL);
/*printk("board_au1200fb_panel_init()\n"); */
return 0;
}
int
board_au1200fb_panel_shutdown (void)
{
/* Remove power */
BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
bcsr->board &= ~(BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD | BCSR_BOARD_LCDBL);
/*printk("board_au1200fb_panel_shutdown()\n"); */
return 0;
}
|
