1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
|
/*
* ALPHAPROJECT AP-SH4A-3A Support.
*
* Copyright (C) 2010 ALPHAPROJECT Co.,Ltd.
* Copyright (C) 2008 Yoshihiro Shimoda
* Copyright (C) 2009 Paul Mundt
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/mtd/physmap.h>
#include <linux/smsc911x.h>
#include <linux/irq.h>
#include <linux/clk.h>
#include <asm/machvec.h>
#include <asm/sizes.h>
#include <asm/clock.h>
static struct mtd_partition nor_flash_partitions[] = {
{
.name = "loader",
.offset = 0x00000000,
.size = 512 * 1024,
},
{
.name = "bootenv",
.offset = MTDPART_OFS_APPEND,
.size = 512 * 1024,
},
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = 4 * 1024 * 1024,
},
{
.name = "data",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
},
};
static struct physmap_flash_data nor_flash_data = {
.width = 4,
.parts = nor_flash_partitions,
.nr_parts = ARRAY_SIZE(nor_flash_partitions),
};
static struct resource nor_flash_resources[] = {
[0] = {
.start = 0x00000000,
.end = 0x01000000 - 1,
.flags = IORESOURCE_MEM,
}
};
static struct platform_device nor_flash_device = {
.name = "physmap-flash",
.dev = {
.platform_data = &nor_flash_data,
},
.num_resources = ARRAY_SIZE(nor_flash_resources),
.resource = nor_flash_resources,
};
static struct resource smsc911x_resources[] = {
[0] = {
.name = "smsc911x-memory",
.start = 0xA4000000,
.end = 0xA4000000 + SZ_256 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.name = "smsc911x-irq",
.start = evt2irq(0x200),
.end = evt2irq(0x200),
.flags = IORESOURCE_IRQ,
},
};
static struct smsc911x_platform_config smsc911x_config = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
.flags = SMSC911X_USE_16BIT,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct platform_device smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(smsc911x_resources),
.resource = smsc911x_resources,
.dev = {
.platform_data = &smsc911x_config,
},
};
static struct platform_device *apsh4a3a_devices[] __initdata = {
&nor_flash_device,
&smsc911x_device,
};
static int __init apsh4a3a_devices_setup(void)
{
return platform_add_devices(apsh4a3a_devices,
ARRAY_SIZE(apsh4a3a_devices));
}
device_initcall(apsh4a3a_devices_setup);
static int apsh4a3a_clk_init(void)
{
struct clk *clk;
int ret;
clk = clk_get(NULL, "extal");
if (!clk || IS_ERR(clk))
return PTR_ERR(clk);
ret = clk_set_rate(clk, 33333000);
clk_put(clk);
return ret;
}
/* Initialize the board */
static void __init apsh4a3a_setup(char **cmdline_p)
{
printk(KERN_INFO "Alpha Project AP-SH4A-3A support:\n");
}
static void __init apsh4a3a_init_irq(void)
{
plat_irq_setup_pins(IRQ_MODE_IRQ7654);
}
/* Return the board specific boot mode pin configuration */
static int apsh4a3a_mode_pins(void)
{
int value = 0;
/* These are the factory default settings of SW1 and SW2.
* If you change these dip switches then you will need to
* adjust the values below as well.
*/
value &= ~MODE_PIN0; /* Clock Mode 16 */
value &= ~MODE_PIN1;
value &= ~MODE_PIN2;
value &= ~MODE_PIN3;
value |= MODE_PIN4;
value &= ~MODE_PIN5; /* 16-bit Area0 bus width */
value |= MODE_PIN6; /* Area 0 SRAM interface */
value |= MODE_PIN7;
value |= MODE_PIN8; /* Little Endian */
value |= MODE_PIN9; /* Master Mode */
value |= MODE_PIN10; /* Crystal resonator */
value |= MODE_PIN11; /* Display Unit */
value |= MODE_PIN12;
value &= ~MODE_PIN13; /* 29-bit address mode */
value |= MODE_PIN14; /* No PLL step-up */
return value;
}
/*
* The Machine Vector
*/
static struct sh_machine_vector mv_apsh4a3a __initmv = {
.mv_name = "AP-SH4A-3A",
.mv_setup = apsh4a3a_setup,
.mv_clk_init = apsh4a3a_clk_init,
.mv_init_irq = apsh4a3a_init_irq,
.mv_mode_pins = apsh4a3a_mode_pins,
};
|
