path: root/drivers/net/gianfar.c

/* 
 * drivers/net/gianfar.c
 *
 * Gianfar Ethernet Driver
 * Driver for FEC on MPC8540 and TSEC on MPC8540/MPC8560
 * Based on 8260_io/fcc_enet.c
 *
 * Author: Andy Fleming
 * Maintainer: Kumar Gala (kumar.gala@freescale.com)
 *
 * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
 *
 * This program is free software; you can redistribute  it and/or modify it
 * under  the terms of  the GNU General  Public License as published by the
 * Free Software Foundation;  either version 2 of the  License, or (at your
 * option) any later version.
 *
 *  Gianfar:  AKA Lambda Draconis, "Dragon"
 *  RA 11 31 24.2
 *  Dec +69 19 52
 *  V 3.84
 *  B-V +1.62
 *
 *  Theory of operation
 *  This driver is designed for the Triple-speed Ethernet
 *  controllers on the Freescale 8540/8560 integrated processors,
 *  as well as the Fast Ethernet Controller on the 8540.  
 *  
 *  The driver is initialized through platform_device.  Structures which
 *  define the configuration needed by the board are defined in a
 *  board structure in arch/ppc/platforms (though I do not
 *  discount the possibility that other architectures could one
 *  day be supported.  One assumption the driver currently makes
 *  is that the PHY is configured in such a way to advertise all
 *  capabilities.  This is a sensible default, and on certain
 *  PHYs, changing this default encounters substantial errata
 *  issues.  Future versions may remove this requirement, but for
 *  now, it is best for the firmware to ensure this is the case.
 *
 *  The Gianfar Ethernet Controller uses a ring of buffer
 *  descriptors.  The beginning is indicated by a register
 *  pointing to the physical address of the start of the ring. 
 *  The end is determined by a "wrap" bit being set in the 
 *  last descriptor of the ring.
 *
 *  When a packet is received, the RXF bit in the
 *  IEVENT register is set, triggering an interrupt when the 
 *  corresponding bit in the IMASK register is also set (if
 *  interrupt coalescing is active, then the interrupt may not
 *  happen immediately, but will wait until either a set number
 *  of frames or amount of time have passed.).  In NAPI, the
 *  interrupt handler will signal there is work to be done, and
 *  exit.  Without NAPI, the packet(s) will be handled
 *  immediately.  Both methods will start at the last known empty
 *  descriptor, and process every subsequent descriptor until there 
 *  are none left with data (NAPI will stop after a set number of
 *  packets to give time to other tasks, but will eventually
 *  process all the packets).  The data arrives inside a
 *  pre-allocated skb, and so after the skb is passed up to the
 *  stack, a new skb must be allocated, and the address field in
 *  the buffer descriptor must be updated to indicate this new
 *  skb.
 *
 *  When the kernel requests that a packet be transmitted, the
 *  driver starts where it left off last time, and points the
 *  descriptor at the buffer which was passed in.  The driver
 *  then informs the DMA engine that there are packets ready to
 *  be transmitted.  Once the controller is finished transmitting
 *  the packet, an interrupt may be triggered (under the same
 *  conditions as for reception, but depending on the TXF bit).
 *  The driver then cleans up the buffer.
 */

#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/mm.h>
#include <linux/device.h>

#include <asm/io.h>
#include <asm/irq.h>
#include <asm/uaccess.h>
#include <linux/module.h>
#include <linux/version.h>
#include <linux/dma-mapping.h>
#include <linux/crc32.h>

#include "gianfar.h"
#include "gianfar_phy.h"

#define TX_TIMEOUT      (1*HZ)
#define SKB_ALLOC_TIMEOUT 1000000
#undef BRIEF_GFAR_ERRORS
#undef VERBOSE_GFAR_ERRORS

#ifdef CONFIG_GFAR_NAPI
#define RECEIVE(x) netif_receive_skb(x)
#else
#define RECEIVE(x) netif_rx(x)
#endif

const char gfar_driver_name[] = "Gianfar Ethernet";
const char gfar_driver_version[] = "1.1";

int startup_gfar(struct net_device *dev);
static int gfar_enet_open(struct net_device *dev);
static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev);
static void gfar_timeout(struct net_device *dev);
static int gfar_close(struct net_device *dev);
struct sk_buff *gfar_new_skb(struct net_device *dev, struct rxbd8 *bdp);
static struct net_device_stats *gfar_get_stats(struct net_device *dev);
static int gfar_set_mac_address(struct net_device *dev);
static int gfar_change_mtu(struct net_device *dev, int new_mtu);
static irqreturn_t gfar_error(int irq, void *dev_id, struct pt_regs *regs);
static irqreturn_t gfar_transmit(int irq, void *dev_id, struct pt_regs *regs);
irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs);
static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs);
static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs);
static void gfar_phy_change(void *data);
static void gfar_phy_timer(unsigned long data);
static void adjust_link(struct net_device *dev);
static void init_registers(struct net_device *dev);
static int init_phy(struct net_device *dev);
static int gfar_probe(struct device *device);
static int gfar_remove(struct device *device);
void free_skb_resources(struct gfar_private *priv);
static void gfar_set_multi(struct net_device *dev);
static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr);
#ifdef CONFIG_GFAR_NAPI
static int gfar_poll(struct net_device *dev, int *budget);
#endif
static int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit);
static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, int length);
static void gfar_phy_startup_timer(unsigned long data);

extern struct ethtool_ops gfar_ethtool_ops;

MODULE_AUTHOR("Freescale Semiconductor, Inc");
MODULE_DESCRIPTION("Gianfar Ethernet Driver");
MODULE_LICENSE("GPL");

static int gfar_probe(struct device *device)
{
	u32 tempval;
	struct net_device *dev = NULL;
	struct gfar_private *priv = NULL;
	struct platform_device *pdev = to_platform_device(device);
	struct gianfar_platform_data *einfo;
	struct resource *r;
	int idx;
	int err = 0;
	int dev_ethtool_ops = 0;

	einfo = (struct gianfar_platform_data *) pdev->dev.platform_data;

	if (einfo == NULL) {
		printk(KERN_ERR "gfar %d: Missing additional data!\n",
		       pdev->id);

		return -ENODEV;
	}

	/* Create an ethernet device instance */
	dev = alloc_etherdev(sizeof (*priv));

	if (dev == NULL)
		return -ENOMEM;

	priv = netdev_priv(dev);

	/* Set the info in the priv to the current info */
	priv->einfo = einfo;

	/* fill out IRQ fields */
	if (einfo->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) {
		priv->interruptTransmit = platform_get_irq_byname(pdev, "tx");
		priv->interruptReceive = platform_get_irq_byname(pdev, "rx");
		priv->interruptError = platform_get_irq_byname(pdev, "error");
	} else {
		priv->interruptTransmit = platform_get_irq(pdev, 0);
	}

	/* get a pointer to the register memory */
	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	priv->regs = (struct gfar *)
		ioremap(r->start, sizeof (struct gfar));

	if (priv->regs == NULL) {
		err = -ENOMEM;
		goto regs_fail;
	}

	/* Set the PHY base address */
	priv->phyregs = (struct gfar *)
	    ioremap(einfo->phy_reg_addr, sizeof (struct gfar));

	if (priv->phyregs == NULL) {
		err = -ENOMEM;
		goto phy_regs_fail;
	}

	spin_lock_init(&priv->lock);

	dev_set_drvdata(device, dev);

	/* Stop the DMA engine now, in case it was running before */
	/* (The firmware could have used it, and left it running). */
	/* To do this, we write Graceful Receive Stop and Graceful */
	/* Transmit Stop, and then wait until the corresponding bits */
	/* in IEVENT indicate the stops have completed. */
	tempval = gfar_read(&priv->regs->dmactrl);
	tempval &= ~(DMACTRL_GRS | DMACTRL_GTS);
	gfar_write(&priv->regs->dmactrl, tempval);

	tempval = gfar_read(&priv->regs->dmactrl);
	tempval |= (DMACTRL_GRS | DMACTRL_GTS);
	gfar_write(&priv->regs->dmactrl, tempval);

	while (!(gfar_read(&priv->regs->ievent) & (IEVENT_GRSC | IEVENT_GTSC)))
		cpu_relax();

	/* Reset MAC layer */
	gfar_write(&priv->regs->maccfg1, MACCFG1_SOFT_RESET);

	tempval = (MACCFG1_TX_FLOW | MACCFG1_RX_FLOW);
	gfar_write(&priv->regs->maccfg1, tempval);

	/* Initialize MACCFG2. */
	gfar_write(&priv->regs->maccfg2, MACCFG2_INIT_SETTINGS);

	/* Initialize ECNTRL */
	gfar_write(&priv->regs->ecntrl, ECNTRL_INIT_SETTINGS);

	/* Copy the station address into the dev structure, */
	memcpy(dev->dev_addr, einfo->mac_addr, MAC_ADDR_LEN);

	/* Set the dev->base_addr to the gfar reg region */
	dev->base_addr = (unsigned long) (priv->regs);

	SET_MODULE_OWNER(dev);
	SET_NETDEV_DEV(dev, device);

	/* Fill in the dev structure */
	dev->open = gfar_enet_open;
	dev->hard_start_xmit = gfar_start_xmit;
	dev->tx_timeout = gfar_timeout;
	dev->watchdog_timeo = TX_TIMEOUT;
#ifdef CONFIG_GFAR_NAPI
	dev->poll = gfar_poll;
	dev->weight = GFAR_DEV_WEIGHT;
#endif
	dev->stop = gfar_close;
	dev->get_stats = gfar_get_stats;
	dev->change_mtu = gfar_change_mtu;
	dev->mtu = 1500;
	dev->set_multicast_list = gfar_set_multi;

	/* Index into the array of possible ethtool
	 * ops to catch all 4 possibilities */
	if((priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_RMON) == 0)
		dev_ethtool_ops += 1;

	if((priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_COALESCE) == 0)
		dev_ethtool_ops += 2;

	dev->ethtool_ops = gfar_op_array[dev_ethtool_ops];

	priv->rx_buffer_size = DEFAULT_RX_BUFFER_SIZE;
#ifdef CONFIG_GFAR_BUFSTASH
	priv->rx_stash_size = STASH_LENGTH;
#endif
	priv->tx_ring_size = DEFAULT_TX_RING_SIZE;
	priv->rx_ring_size = DEFAULT_RX_RING_SIZE;

	priv->txcoalescing = DEFAULT_TX_COALESCE;
	priv->txcount = DEFAULT_TXCOUNT;
	priv->txtime = DEFAULT_TXTIME;
	priv->rxcoalescing = DEFAULT_RX_COALESCE;
	priv->rxcount = DEFAULT_RXCOUNT;
	priv->rxtime = DEFAULT_RXTIME;

	err = register_netdev(dev);

	if (err) {
		printk(KERN_ERR "%s: Cannot register net device, aborting.\n",
				dev->name);
		goto register_fail;
	}

	/* Print out the device info */
	printk(KERN_INFO DEVICE_NAME, dev->name);
	for (idx = 0; idx < 6; idx++)
		printk("%2.2x%c", dev->dev_addr[idx], idx == 5 ? ' ' : ':');
	printk("\n");

	/* Even more device info helps when determining which kernel */
	/* provided which set of benchmarks.  Since this is global for all */
	/* devices, we only print it once */
#ifdef CONFIG_GFAR_NAPI
	printk(KERN_INFO "%s: Running with NAPI enabled\n", dev->name);
#else
	printk(KERN_INFO "%s: Running with NAPI disabled\n", dev->name);
#endif
	printk(KERN_INFO "%s: %d/%d RX/TX BD ring size\n",
	       dev->name, priv->rx_ring_size, priv->tx_ring_size);

	return 0;

register_fail:
	iounmap((void *) priv->phyregs);
phy_regs_fail:
	iounmap((void *) priv->regs);
regs_fail:
	free_netdev(dev);
	return -ENOMEM;
}

static int gfar_remove(struct device *device)
{
	struct net_device *dev = dev_get_drvdata(device);
	struct gfar_private *priv = netdev_priv(dev);

	dev_set_drvdata(device, NULL);

	iounmap((void *) priv->regs);
	iounmap((void *) priv->phyregs);
	free_netdev(dev);

	return 0;
}


/* Configure the PHY for dev.
 * returns 0 if success.  -1 if failure
 */
static int init_phy(struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);
	struct phy_info *curphy;
	unsigned int timeout = PHY_INIT_TIMEOUT;
	struct gfar *phyregs = priv->phyregs;
	struct gfar_mii_info *mii_info;
	int err;

	priv->oldlink = 0;
	priv->oldspeed = 0;
	priv->oldduplex = -1;

	mii_info = kmalloc(sizeof(struct gfar_mii_info),
			GFP_KERNEL);

	if(NULL == mii_info) {
		printk(KERN_ERR "%s: Could not allocate mii_info\n", 
				dev->name);
		return -ENOMEM;
	}

	mii_info->speed = SPEED_1000;
	mii_info->duplex = DUPLEX_FULL;
	mii_info->pause = 0;
	mii_info->link = 1;

	mii_info->advertising = (ADVERTISED_10baseT_Half |
			ADVERTISED_10baseT_Full |
			ADVERTISED_100baseT_Half |
			ADVERTISED_100baseT_Full |
			ADVERTISED_1000baseT_Full);
	mii_info->autoneg = 1;

	spin_lock_init(&mii_info->mdio_lock);

	mii_info->mii_id = priv->einfo->phyid;

	mii_info->dev = dev;

	mii_info->mdio_read = &read_phy_reg;
	mii_info->mdio_write = &write_phy_reg;

	priv->mii_info = mii_info;

	/* Reset the management interface */
	gfar_write(&phyregs->miimcfg, MIIMCFG_RESET);

	/* Setup the MII Mgmt clock speed */
	gfar_write(&phyregs->miimcfg, MIIMCFG_INIT_VALUE);

	/* Wait until the bus is free */
	while ((gfar_read(&phyregs->miimind) & MIIMIND_BUSY) &&
			timeout--)
		cpu_relax();

	if(timeout <= 0) {
		printk(KERN_ERR "%s: The MII Bus is stuck!\n",
				dev->name);
		err = -1;
		goto bus_fail;
	}

	/* get info for this PHY */
	curphy = get_phy_info(priv->mii_info);

	if (curphy == NULL) {
		printk(KERN_ERR "%s: No PHY found\n", dev->name);
		err = -1;
		goto no_phy;
	}

	mii_info->phyinfo = curphy;

	/* Run the commands which initialize the PHY */
	if(curphy->init) {
		err = curphy->init(priv->mii_info);

		if (err) 
			goto phy_init_fail;
	}

	return 0;

phy_init_fail:
no_phy:
bus_fail:
	kfree(mii_info);

	return err;
}

static void init_registers(struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);

	/* Clear IEVENT */
	gfar_write(&priv->regs->ievent, IEVENT_INIT_CLEAR);

	/* Initialize IMASK */
	gfar_write(&priv->regs->imask, IMASK_INIT_CLEAR);

	/* Init hash registers to zero */
	gfar_write(&priv->regs->iaddr0, 0);
	gfar_write(&priv->regs->iaddr1, 0);
	gfar_write(&priv->regs->iaddr2, 0);
	gfar_write(&priv->regs->iaddr3, 0);
	gfar_write(&priv->regs->iaddr4, 0);
	gfar_write(&priv->regs->iaddr5, 0);
	gfar_write(&priv->regs->iaddr6, 0);
	gfar_write(&priv->regs->iaddr7, 0);

	gfar_write(&priv->regs->gaddr0, 0);
	gfar_write(&priv->regs->gaddr1, 0);
	gfar_write(&priv->regs->gaddr2, 0);
	gfar_write(&priv->regs->gaddr3, 0);
	gfar_write(&priv->regs->gaddr4, 0);
	gfar_write(&priv->regs->gaddr5, 0);
	gfar_write(&priv->regs->gaddr6, 0);
	gfar_write(&priv->regs->gaddr7, 0);

	/* Zero out rctrl */
	gfar_write(&priv->regs->rctrl, 0x00000000);

	/* Zero out the rmon mib registers if it has them */
	if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_RMON) {
		memset((void *) &(priv->regs->rmon), 0,
		       sizeof (struct rmon_mib));

		/* Mask off the CAM interrupts */
		gfar_write(&priv->regs->rmon.cam1, 0xffffffff);
		gfar_write(&priv->regs->rmon.cam2, 0xffffffff);
	}

	/* Initialize the max receive buffer length */
	gfar_write(&priv->regs->mrblr, priv->rx_buffer_size);

#ifdef CONFIG_GFAR_BUFSTASH
	/* If we are stashing buffers, we need to set the
	 * extraction length to the size of the buffer */
	gfar_write(&priv->regs->attreli, priv->rx_stash_size << 16);
#endif

	/* Initialize the Minimum Frame Length Register */
	gfar_write(&priv->regs->minflr, MINFLR_INIT_SETTINGS);

	/* Setup Attributes so that snooping is on for rx */
	gfar_write(&priv->regs->attr, ATTR_INIT_SETTINGS);
	gfar_write(&priv->regs->attreli, ATTRELI_INIT_SETTINGS);

	/* Assign the TBI an address which won't conflict with the PHYs */
	gfar_write(&priv->regs->tbipa, TBIPA_VALUE);
}

void stop_gfar(struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);
	struct gfar *regs = priv->regs;
	unsigned long flags;
	u32 tempval;

	/* Lock it down */
	spin_lock_irqsave(&priv->lock, flags);

	/* Tell the kernel the link is down */
	priv->mii_info->link = 0;
	adjust_link(dev);

	/* Mask all interrupts */
	gfar_write(&regs->imask, IMASK_INIT_CLEAR);

	/* Clear all interrupts */
	gfar_write(&regs->ievent, IEVENT_INIT_CLEAR);

	/* Stop the DMA, and wait for it to stop */
	tempval = gfar_read(&priv->regs->dmactrl);
	if ((tempval & (DMACTRL_GRS | DMACTRL_GTS))
	    != (DMACTRL_GRS | DMACTRL_GTS)) {
		tempval |= (DMACTRL_GRS | DMACTRL_GTS);
		gfar_write(&priv->regs->dmactrl, tempval);

		while (!(gfar_read(&priv->regs->ievent) &
			 (IEVENT_GRSC | IEVENT_GTSC)))
			cpu_relax();
	}

	/* Disable Rx and Tx */
	tempval = gfar_read(&regs->maccfg1);
	tempval &= ~(MACCFG1_RX_EN | MACCFG1_TX_EN);
	gfar_write(&regs->maccfg1, tempval);

	if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
		/* Clear any pending interrupts */
		mii_clear_phy_interrupt(priv->mii_info);

		/* Disable PHY Interrupts */
		mii_configure_phy_interrupt(priv->mii_info, 
				MII_INTERRUPT_DISABLED);
	}

	spin_unlock_irqrestore(&priv->lock, flags);

	/* Free the IRQs */
	if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) {
		free_irq(priv->interruptError, dev);
		free_irq(priv->interruptTransmit, dev);
		free_irq(priv->interruptReceive, dev);
	} else {
		free_irq(priv->interruptTransmit, dev);
	}

	if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
		free_irq(priv->einfo->interruptPHY, dev);
	} else {
		del_timer_sync(&priv->phy_info_timer);
	}

	free_skb_resources(priv);

	dma_free_coherent(NULL,
			sizeof(struct txbd8)*priv->tx_ring_size
			+ sizeof(struct rxbd8)*priv->rx_ring_size,
			priv->tx_bd_base,
			gfar_read(&regs->tbase));
}

/* If there are any tx skbs or rx skbs still around, free them.
 * Then free tx_skbuff and rx_skbuff */
void free_skb_resources(struct gfar_private *priv)
{
	struct rxbd8 *rxbdp;
	struct txbd8 *txbdp;
	int i;

	/* Go through all the buffer descriptors and free their data buffers */
	txbdp = priv->tx_bd_base;

	for (i = 0; i < priv->tx_ring_size; i++) {

		if (priv->tx_skbuff[i]) {
			dma_unmap_single(NULL, txbdp->bufPtr,
					txbdp->length,
					DMA_TO_DEVICE);
			dev_kfree_skb_any(priv->tx_skbuff[i]);
			priv->tx_skbuff[i] = NULL;
		}
	}

	kfree(priv->tx_skbuff);

	rxbdp = priv->rx_bd_base;

	/* rx_skbuff is not guaranteed to be allocated, so only
	 * free it and its contents if it is allocated */
	if(priv->rx_skbuff != NULL) {
		for (i = 0; i < priv->rx_ring_size; i++) {
			if (priv->rx_skbuff[i]) {
				dma_unmap_single(NULL, rxbdp->bufPtr,
						priv->rx_buffer_size
						+ RXBUF_ALIGNMENT,
						DMA_FROM_DEVICE);

				dev_kfree_skb_any(priv->rx_skbuff[i]);
				priv->rx_skbuff[i] = NULL;
			}

			rxbdp->status = 0;
			rxbdp->length = 0;
			rxbdp->bufPtr = 0;

			rxbdp++;
		}

		kfree(priv->rx_skbuff);
	}
}

/* Bring the controller up and running */
int startup_gfar(struct net_device *dev)
{
	struct txbd8 *txbdp;
	struct rxbd8 *rxbdp;
	dma_addr_t addr;
	unsigned long vaddr;
	int i;
	struct gfar_private *priv = netdev_priv(dev);
	struct gfar *regs = priv->regs;
	u32 tempval;
	int err = 0;

	gfar_write(&regs->imask, IMASK_INIT_CLEAR);

	/* Allocate memory for the buffer descriptors */
	vaddr = (unsigned long) dma_alloc_coherent(NULL, 
			sizeof (struct txbd8) * priv->tx_ring_size +
			sizeof (struct rxbd8) * priv->rx_ring_size,
			&addr, GFP_KERNEL);

	if (vaddr == 0) {
		printk(KERN_ERR "%s: Could not allocate buffer descriptors!\n",
		       dev->name);
		return -ENOMEM;
	}

	priv->tx_bd_base = (struct txbd8 *) vaddr;

	/* enet DMA only understands physical addresses */
	gfar_write(&regs->tbase, addr);

	/* Start the rx descriptor ring where the tx ring leaves off */
	addr = addr + sizeof (struct txbd8) * priv->tx_ring_size;
	vaddr = vaddr + sizeof (struct txbd8) * priv->tx_ring_size;
	priv->rx_bd_base = (struct rxbd8 *) vaddr;
	gfar_write(&regs->rbase, addr);

	/* Setup the skbuff rings */
	priv->tx_skbuff =
	    (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) *
					priv->tx_ring_size, GFP_KERNEL);

	if (priv->tx_skbuff == NULL) {
		printk(KERN_ERR "%s: Could not allocate tx_skbuff\n",
		       dev->name);
		err = -ENOMEM;
		goto tx_skb_fail;
	}

	for (i = 0; i < priv->tx_ring_size; i++)
		priv->tx_skbuff[i] = NULL;

	priv->rx_skbuff =
	    (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) *
					priv->rx_ring_size, GFP_KERNEL);

	if (priv->rx_skbuff == NULL) {
		printk(KERN_ERR "%s: Could not allocate rx_skbuff\n",
		       dev->name);
		err = -ENOMEM;
		goto rx_skb_fail;
	}

	for (i = 0; i < priv->rx_ring_size; i++)
		priv->rx_skbuff[i] = NULL;

	/* Initialize some variables in our dev structure */
	priv->dirty_tx = priv->cur_tx = priv->tx_bd_base;
	priv->cur_rx = priv->rx_bd_base;
	priv->skb_curtx = priv->skb_dirtytx = 0;
	priv->skb_currx = 0;

	/* Initialize Transmit Descriptor Ring */
	txbdp = priv->tx_bd_base;
	for (i = 0; i < priv->tx_ring_size; i++) {
		txbdp->status = 0;
		txbdp->length = 0;
		txbdp->bufPtr = 0;
		txbdp++;
	}

	/* Set the last descriptor in the ring to indicate wrap */
	txbdp--;
	txbdp->status |= TXBD_WRAP;

	rxbdp = priv->rx_bd_base;
	for (i = 0; i < priv->rx_ring_size; i++) {
		struct sk_buff *skb = NULL;

		rxbdp->status = 0;

		skb = gfar_new_skb(dev, rxbdp);

		priv->rx_skbuff[i] = skb;

		rxbdp++;
	}

	/* Set the last descriptor in the ring to wrap */
	rxbdp--;
	rxbdp->status |= RXBD_WRAP;

	/* If the device has multiple interrupts, register for
	 * them.  Otherwise, only register for the one */
	if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) {
		/* Install our interrupt handlers for Error, 
		 * Transmit, and Receive */
		if (request_irq(priv->interruptError, gfar_error,
				0, "enet_error", dev) < 0) {
			printk(KERN_ERR "%s: Can't get IRQ %d\n",
			       dev->name, priv->interruptError);

			err = -1;
			goto err_irq_fail;
		}

		if (request_irq(priv->interruptTransmit, gfar_transmit,
				0, "enet_tx", dev) < 0) {
			printk(KERN_ERR "%s: Can't get IRQ %d\n",
			       dev->name, priv->interruptTransmit);

			err = -1;

			goto tx_irq_fail;
		}

		if (request_irq(priv->interruptReceive, gfar_receive,
				0, "enet_rx", dev) < 0) {
			printk(KERN_ERR "%s: Can't get IRQ %d (receive0)\n",
			       dev->name, priv->interruptReceive);

			err = -1;
			goto rx_irq_fail;
		}
	} else {
		if (request_irq(priv->interruptTransmit, gfar_interrupt,
				0, "gfar_interrupt", dev) < 0) {
			printk(KERN_ERR "%s: Can't get IRQ %d\n",
			       dev->name, priv->interruptError);

			err = -1;
			goto err_irq_fail;
		}
	}

	/* Set up the PHY change work queue */
	INIT_WORK(&priv->tq, gfar_phy_change, dev);

	init_timer(&priv->phy_info_timer);
	priv->phy_info_timer.function = &gfar_phy_startup_timer;
	priv->phy_info_timer.data = (unsigned long) priv->mii_info;
	mod_timer(&priv->phy_info_timer, jiffies + HZ);

	/* Configure the coalescing support */
	if (priv->txcoalescing)
		gfar_write(&regs->txic,
			   mk_ic_value(priv->txcount, priv->txtime));
	else
		gfar_write(&regs->txic, 0);

	if (priv->rxcoalescing)
		gfar_write(&regs->rxic,
			   mk_ic_value(priv->rxcount, priv->rxtime));
	else
		gfar_write(&regs->rxic, 0);

	init_waitqueue_head(&priv->rxcleanupq);

	/* Enable Rx and Tx in MACCFG1 */
	tempval = gfar_read(&regs->maccfg1);
	tempval |= (MACCFG1_RX_EN | MACCFG1_TX_EN);
	gfar_write(&regs->maccfg1, tempval);

	/* Initialize DMACTRL to have WWR and WOP */
	tempval = gfar_read(&priv->regs->dmactrl);
	tempval |= DMACTRL_INIT_SETTINGS;
	gfar_write(&priv->regs->dmactrl, tempval);

	/* Clear THLT, so that the DMA starts polling now */
	gfar_write(&regs->tstat, TSTAT_CLEAR_THALT);

	/* Make sure we aren't stopped */
	tempval = gfar_read(&priv->regs->dmactrl);
	tempval &= ~(DMACTRL_GRS | DMACTRL_GTS);
	gfar_write(&priv->regs->dmactrl, tempval);

	/* Unmask the interrupts we look for */
	gfar_write(&regs->imask, IMASK_DEFAULT);

	return 0;

rx_irq_fail:
	free_irq(priv->interruptTransmit, dev);
tx_irq_fail:
	free_irq(priv->interruptError, dev);
err_irq_fail:
rx_skb_fail:
	free_skb_resources(priv);
tx_skb_fail:
	dma_free_coherent(NULL,
			sizeof(struct txbd8)*priv->tx_ring_size
			+ sizeof(struct rxbd8)*priv->rx_ring_size,
			priv->tx_bd_base,
			gfar_read(&regs->tbase));

	if (priv->mii_info->phyinfo->close)
		priv->mii_info->phyinfo->close(priv->mii_info);

	kfree(priv->mii_info);

	return err;
}

/* Called when something needs to use the ethernet device */
/* Returns 0 for success. */
static int gfar_enet_open(struct net_device *dev)
{
	int err;

	/* Initialize a bunch of registers */
	init_registers(dev);

	gfar_set_mac_address(dev);

	err = init_phy(dev);

	if(err)
		return err;

	err = startup_gfar(dev);

	netif_start_queue(dev);

	return err;
}

/* This is called by the kernel when a frame is ready for transmission. */
/* It is pointed to by the dev->hard_start_xmit function pointer */
static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);
	struct txbd8 *txbdp;

	/* Update transmit stats */
	priv->stats.tx_bytes += skb->len;

	/* Lock priv now */
	spin_lock_irq(&priv->lock);

	/* Point at the first free tx descriptor */
	txbdp = priv->cur_tx;

	/* Clear all but the WRAP status flags */
	txbdp->status &= TXBD_WRAP;

	/* Set buffer length and pointer */
	txbdp->length = skb->len;
	txbdp->bufPtr = dma_map_single(NULL, skb->data, 
			skb->len, DMA_TO_DEVICE);

	/* Save the skb pointer so we can free it later */
	priv->tx_skbuff[priv->skb_curtx] = skb;

	/* Update the current skb pointer (wrapping if this was the last) */
	priv->skb_curtx =
	    (priv->skb_curtx + 1) & TX_RING_MOD_MASK(priv->tx_ring_size);

	/* Flag the BD as interrupt-causing */
	txbdp->status |= TXBD_INTERRUPT;

	/* Flag the BD as ready to go, last in frame, and  */
	/* in need of CRC */
	txbdp->status |= (TXBD_READY | TXBD_LAST | TXBD_CRC);

	dev->trans_start = jiffies;

	/* If this was the last BD in the ring, the next one */
	/* is at the beginning of the ring */
	if (txbdp->status & TXBD_WRAP)
		txbdp = priv->tx_bd_base;
	else
		txbdp++;

	/* If the next BD still needs to be cleaned up, then the bds
	   are full.  We need to tell the kernel to stop sending us stuff. */
	if (txbdp == priv->dirty_tx) {
		netif_stop_queue(dev);

		priv->stats.tx_fifo_errors++;
	}

	/* Update the current txbd to the next one */
	priv->cur_tx = txbdp;

	/* Tell the DMA to go go go */
	gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT);

	/* Unlock priv */
	spin_unlock_irq(&priv->lock);

	return 0;
}

/* Stops the kernel queue, and halts the controller */
static int gfar_close(struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);
	stop_gfar(dev);

	/* Shutdown the PHY */
	if (priv->mii_info->phyinfo->close)
		priv->mii_info->phyinfo->close(priv->mii_info);

	kfree(priv->mii_info);

	netif_stop_queue(dev);

	return 0;
}

/* returns a net_device_stats structure pointer */
static struct net_device_stats * gfar_get_stats(struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);

	return &(priv->stats);
}

/* Changes the mac address if the controller is not running. */
int gfar_set_mac_address(struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);
	int i;
	char tmpbuf[MAC_ADDR_LEN];
	u32 tempval;

	/* Now copy it into the mac registers backwards, cuz */
	/* little endian is silly */
	for (i = 0; i < MAC_ADDR_LEN; i++)
		tmpbuf[MAC_ADDR_LEN - 1 - i] = dev->dev_addr[i];

	gfar_write(&priv->regs->macstnaddr1, *((u32 *) (tmpbuf)));

	tempval = *((u32 *) (tmpbuf + 4));

	gfar_write(&priv->regs->macstnaddr2, tempval);

	return 0;
}


static int gfar_change_mtu(struct net_device *dev, int new_mtu)
{
	int tempsize, tempval;
	struct gfar_private *priv = netdev_priv(dev);
	int oldsize = priv->rx_buffer_size;
	int frame_size = new_mtu + 18;

	if ((frame_size < 64) || (frame_size > JUMBO_FRAME_SIZE)) {
		printk(KERN_ERR "%s: Invalid MTU setting\n", dev->name);
		return -EINVAL;
	}

	tempsize =
	    (frame_size & ~(INCREMENTAL_BUFFER_SIZE - 1)) +
	    INCREMENTAL_BUFFER_SIZE;

	/* Only stop and start the controller if it isn't already
	 * stopped */
	if ((oldsize != tempsize) && (dev->flags & IFF_UP))
		stop_gfar(dev);

	priv->rx_buffer_size = tempsize;

	dev->mtu = new_mtu;

	gfar_write(&priv->regs->mrblr, priv->rx_buffer_size);
	gfar_write(&priv->regs->maxfrm, priv->rx_buffer_size);

	/* If the mtu is larger than the max size for standard
	 * ethernet frames (ie, a jumbo frame), then set maccfg2
	 * to allow huge frames, and to check the length */
	tempval = gfar_read(&priv->regs->maccfg2);

	if (priv->rx_buffer_size > DEFAULT_RX_BUFFER_SIZE)
		tempval |= (MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK);
	else
		tempval &= ~(MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK);

	gfar_write(&priv->regs->maccfg2, tempval);

	if ((oldsize != tempsize) && (dev->flags & IFF_UP))
		startup_gfar(dev);

	return 0;
}

/* gfar_timeout gets called when a packet has not been
 * transmitted after a set amount of time.
 * For now, assume that clearing out all the structures, and
 * starting over will fix the problem. */
static void gfar_timeout(struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);

	priv->stats.tx_errors++;

	if (dev->flags & IFF_UP) {
		stop_gfar(dev);
		startup_gfar(dev);
	}

	netif_schedule(dev);
}

/* Interrupt Handler for Transmit complete */
static irqreturn_t gfar_transmit(int irq, void *dev_id, struct pt_regs *regs)
{
	struct net_device *dev = (struct net_device *) dev_id;
	struct gfar_private *priv = netdev_priv(dev);
	struct txbd8 *bdp;

	/* Clear IEVENT */
	gfar_write(&priv->regs->ievent, IEVENT_TX_MASK);

	/* Lock priv */
	spin_lock(&priv->lock);
	bdp = priv->dirty_tx;
	while ((bdp->status & TXBD_READY) == 0) {
		/* If dirty_tx and cur_tx are the same, then either the */
		/* ring is empty or full now (it could only be full in the beginning, */
		/* obviously).  If it is empty, we are done. */
		if ((bdp == priv->cur_tx) && (netif_queue_stopped(dev) == 0))
			break;

		priv->stats.tx_packets++;

		/* Deferred means some collisions occurred during transmit, */
		/* but we eventually sent the packet. */
		if (bdp->status & TXBD_DEF)
			priv->stats.collisions++;

		/* Free the sk buffer associated with this TxBD */
		dev_kfree_skb_irq(priv->tx_skbuff[priv->skb_dirtytx]);
		priv->tx_skbuff[priv->skb_dirtytx] = NULL;
		priv->skb_dirtytx =
		    (priv->skb_dirtytx +
		     1) & TX_RING_MOD_MASK(priv->tx_ring_size);

		/* update bdp to point at next bd in the ring (wrapping if necessary) */
		if (bdp->status & TXBD_WRAP)
			bdp = priv->tx_bd_base;
		else
			bdp++;

		/* Move dirty_tx to be the next bd */
		priv->dirty_tx = bdp;

		/* We freed a buffer, so now we can restart transmission */
		if (netif_queue_stopped(dev))
			netif_wake_queue(dev);
	} /* while ((bdp->status & TXBD_READY) == 0) */

	/* If we are coalescing the interrupts, reset the timer */
	/* Otherwise, clear it */
	if (priv->txcoalescing)
		gfar_write(&priv->regs->txic,
			   mk_ic_value(priv->txcount, priv->txtime));
	else
		gfar_write(&priv->regs->txic, 0);

	spin_unlock(&priv->lock);

	return IRQ_HANDLED;
}

struct sk_buff * gfar_new_skb(struct net_device *dev, struct rxbd8 *bdp)
{
	struct gfar_private *priv = netdev_priv(dev);
	struct sk_buff *skb = NULL;
	unsigned int timeout = SKB_ALLOC_TIMEOUT;

	/* We have to allocate the skb, so keep trying till we succeed */
	while ((!skb) && timeout--)
		skb = dev_alloc_skb(priv->rx_buffer_size + RXBUF_ALIGNMENT);

	if (skb == NULL)
		return NULL;

	/* We need the data buffer to be aligned properly.  We will reserve
	 * as many bytes as needed to align the data properly
	 */
	skb_reserve(skb,
		    RXBUF_ALIGNMENT -
		    (((unsigned) skb->data) & (RXBUF_ALIGNMENT - 1)));

	skb->dev = dev;

	bdp->bufPtr = dma_map_single(NULL, skb->data,
			priv->rx_buffer_size + RXBUF_ALIGNMENT, 
			DMA_FROM_DEVICE);

	bdp->length = 0;

	/* Mark the buffer empty */
	bdp->status |= (RXBD_EMPTY | RXBD_INTERRUPT);

	return skb;
}

static inline void count_errors(unsigned short status, struct gfar_private *priv)
{
	struct net_device_stats *stats = &priv->stats;
	struct gfar_extra_stats *estats = &priv->extra_stats;

	/* If the packet was truncated, none of the other errors
	 * matter */
	if (status & RXBD_TRUNCATED) {
		stats->rx_length_errors++;

		estats->rx_trunc++;

		return;
	}
	/* Count the errors, if there were any */
	if (status & (RXBD_LARGE | RXBD_SHORT)) {
		stats->rx_length_errors++;

		if (status & RXBD_LARGE)
			estats->rx_large++;
		else
			estats->rx_short++;
	}
	if (status & RXBD_NONOCTET) {
		stats->rx_frame_errors++;
		estats->rx_nonoctet++;
	}
	if (status & RXBD_CRCERR) {
		estats->rx_crcerr++;
		stats->rx_crc_errors++;
	}
	if (status & RXBD_OVERRUN) {
		estats->rx_overrun++;
		stats->rx_crc_errors++;
	}
}

irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs)
{
	struct net_device *dev = (struct net_device *) dev_id;
	struct gfar_private *priv = netdev_priv(dev);

#ifdef CONFIG_GFAR_NAPI
	u32 tempval;
#endif

	/* Clear IEVENT, so rx interrupt isn't called again
	 * because of this interrupt */
	gfar_write(&priv->regs->ievent, IEVENT_RX_MASK);

	/* support NAPI */
#ifdef CONFIG_GFAR_NAPI
	if (netif_rx_schedule_prep(dev)) {
		tempval = gfar_read(&priv->regs->imask);
		tempval &= IMASK_RX_DISABLED;
		gfar_write(&priv->regs->imask, tempval);

		__netif_rx_schedule(dev);
	} else {
#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: receive called twice (%x)[%x]\n",
		       dev->name, gfar_read(&priv->regs->ievent),
		       gfar_read(&priv->regs->imask));
#endif
	}
#else

	spin_lock(&priv->lock);
	gfar_clean_rx_ring(dev, priv->rx_ring_size);

	/* If we are coalescing interrupts, update the timer */
	/* Otherwise, clear it */
	if (priv->rxcoalescing)
		gfar_write(&priv->regs->rxic,
			   mk_ic_value(priv->rxcount, priv->rxtime));
	else
		gfar_write(&priv->regs->rxic, 0);

	/* Just in case we need to wake the ring param changer */
	priv->rxclean = 1;

	spin_unlock(&priv->lock);
#endif

	return IRQ_HANDLED;
}


/* gfar_process_frame() -- handle one incoming packet if skb
 * isn't NULL.  */
static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb,
		int length)
{
	struct gfar_private *priv = netdev_priv(dev);

	if (skb == NULL) {
#ifdef BRIEF_GFAR_ERRORS
		printk(KERN_WARNING "%s: Missing skb!!.\n",
				dev->name);
#endif
		priv->stats.rx_dropped++;
		priv->extra_stats.rx_skbmissing++;
	} else {
		/* Prep the skb for the packet */
		skb_put(skb, length);

		/* Tell the skb what kind of packet this is */
		skb->protocol = eth_type_trans(skb, dev);

		/* Send the packet up the stack */
		if (RECEIVE(skb) == NET_RX_DROP) {
			priv->extra_stats.kernel_dropped++;
		}
	}

	return 0;
}

/* gfar_clean_rx_ring() -- Processes each frame in the rx ring
 *   until the budget/quota has been reached. Returns the number 
 *   of frames handled
 */
static int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit)
{
	struct rxbd8 *bdp;
	struct sk_buff *skb;
	u16 pkt_len;
	int howmany = 0;
	struct gfar_private *priv = netdev_priv(dev);

	/* Get the first full descriptor */
	bdp = priv->cur_rx;

	while (!((bdp->status & RXBD_EMPTY) || (--rx_work_limit < 0))) {
		skb = priv->rx_skbuff[priv->skb_currx];

		if (!(bdp->status &
		      (RXBD_LARGE | RXBD_SHORT | RXBD_NONOCTET
		       | RXBD_CRCERR | RXBD_OVERRUN | RXBD_TRUNCATED))) {
			/* Increment the number of packets */
			priv->stats.rx_packets++;
			howmany++;

			/* Remove the FCS from the packet length */
			pkt_len = bdp->length - 4;

			gfar_process_frame(dev, skb, pkt_len);

			priv->stats.rx_bytes += pkt_len;
		} else {
			count_errors(bdp->status, priv);

			if (skb)
				dev_kfree_skb_any(skb);

			priv->rx_skbuff[priv->skb_currx] = NULL;
		}

		dev->last_rx = jiffies;

		/* Clear the status flags for this buffer */
		bdp->status &= ~RXBD_STATS;

		/* Add another skb for the future */
		skb = gfar_new_skb(dev, bdp);
		priv->rx_skbuff[priv->skb_currx] = skb;

		/* Update to the next pointer */
		if (bdp->status & RXBD_WRAP)
			bdp = priv->rx_bd_base;
		else
			bdp++;

		/* update to point at the next skb */
		priv->skb_currx =
		    (priv->skb_currx +
		     1) & RX_RING_MOD_MASK(priv->rx_ring_size);

	}

	/* Update the current rxbd pointer to be the next one */
	priv->cur_rx = bdp;

	/* If no packets have arrived since the
	 * last one we processed, clear the IEVENT RX and
	 * BSY bits so that another interrupt won't be
	 * generated when we set IMASK */
	if (bdp->status & RXBD_EMPTY)
		gfar_write(&priv->regs->ievent, IEVENT_RX_MASK);

	return howmany;
}

#ifdef CONFIG_GFAR_NAPI
static int gfar_poll(struct net_device *dev, int *budget)
{
	int howmany;
	struct gfar_private *priv = netdev_priv(dev);
	int rx_work_limit = *budget;

	if (rx_work_limit > dev->quota)
		rx_work_limit = dev->quota;

	howmany = gfar_clean_rx_ring(dev, rx_work_limit);

	dev->quota -= howmany;
	rx_work_limit -= howmany;
	*budget -= howmany;

	if (rx_work_limit >= 0) {
		netif_rx_complete(dev);

		/* Clear the halt bit in RSTAT */
		gfar_write(&priv->regs->rstat, RSTAT_CLEAR_RHALT);

		gfar_write(&priv->regs->imask, IMASK_DEFAULT);

		/* If we are coalescing interrupts, update the timer */
		/* Otherwise, clear it */
		if (priv->rxcoalescing)
			gfar_write(&priv->regs->rxic,
				   mk_ic_value(priv->rxcount, priv->rxtime));
		else
			gfar_write(&priv->regs->rxic, 0);

		/* Signal to the ring size changer that it's safe to go */
		priv->rxclean = 1;
	}

	return (rx_work_limit < 0) ? 1 : 0;
}
#endif

/* The interrupt handler for devices with one interrupt */
static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
	struct net_device *dev = dev_id;
	struct gfar_private *priv = netdev_priv(dev);

	/* Save ievent for future reference */
	u32 events = gfar_read(&priv->regs->ievent);

	/* Clear IEVENT */
	gfar_write(&priv->regs->ievent, events);

	/* Check for reception */
	if ((events & IEVENT_RXF0) || (events & IEVENT_RXB0))
		gfar_receive(irq, dev_id, regs);

	/* Check for transmit completion */
	if ((events & IEVENT_TXF) || (events & IEVENT_TXB))
		gfar_transmit(irq, dev_id, regs);

	/* Update error statistics */
	if (events & IEVENT_TXE) {
		priv->stats.tx_errors++;

		if (events & IEVENT_LC)
			priv->stats.tx_window_errors++;
		if (events & IEVENT_CRL)
			priv->stats.tx_aborted_errors++;
		if (events & IEVENT_XFUN) {
#ifdef VERBOSE_GFAR_ERRORS
			printk(KERN_WARNING "%s: tx underrun. dropped packet\n",
			       dev->name);
#endif
			priv->stats.tx_dropped++;
			priv->extra_stats.tx_underrun++;

			/* Reactivate the Tx Queues */
			gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT);
		}
	}
	if (events & IEVENT_BSY) {
		priv->stats.rx_errors++;
		priv->extra_stats.rx_bsy++;

		gfar_receive(irq, dev_id, regs);

#ifndef CONFIG_GFAR_NAPI
		/* Clear the halt bit in RSTAT */
		gfar_write(&priv->regs->rstat, RSTAT_CLEAR_RHALT);
#endif

#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: busy error (rhalt: %x)\n", dev->name,
		       gfar_read(&priv->regs->rstat));
#endif
	}
	if (events & IEVENT_BABR) {
		priv->stats.rx_errors++;
		priv->extra_stats.rx_babr++;

#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: babbling error\n", dev->name);
#endif
	}
	if (events & IEVENT_EBERR) {
		priv->extra_stats.eberr++;
#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: EBERR\n", dev->name);
#endif
	}
	if (events & IEVENT_RXC) {
#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: control frame\n", dev->name);
#endif
	}

	if (events & IEVENT_BABT) {
		priv->extra_stats.tx_babt++;
#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: babt error\n", dev->name);
#endif
	}

	return IRQ_HANDLED;
}

static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
	struct net_device *dev = (struct net_device *) dev_id;
	struct gfar_private *priv = netdev_priv(dev);

	/* Clear the interrupt */
	mii_clear_phy_interrupt(priv->mii_info);

	/* Disable PHY interrupts */
	mii_configure_phy_interrupt(priv->mii_info,
			MII_INTERRUPT_DISABLED);

	/* Schedule the phy change */
	schedule_work(&priv->tq);

	return IRQ_HANDLED;
}

/* Scheduled by the phy_interrupt/timer to handle PHY changes */
static void gfar_phy_change(void *data)
{
	struct net_device *dev = (struct net_device *) data;
	struct gfar_private *priv = netdev_priv(dev);
	int result = 0;

	/* Delay to give the PHY a chance to change the
	 * register state */
	msleep(1);

	/* Update the link, speed, duplex */
	result = priv->mii_info->phyinfo->read_status(priv->mii_info);

	/* Adjust the known status as long as the link
	 * isn't still coming up */
	if((0 == result) || (priv->mii_info->link == 0))
		adjust_link(dev);

	/* Reenable interrupts, if needed */
	if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR)
		mii_configure_phy_interrupt(priv->mii_info,
				MII_INTERRUPT_ENABLED);
}

/* Called every so often on systems that don't interrupt
 * the core for PHY changes */
static void gfar_phy_timer(unsigned long data)
{
	struct net_device *dev = (struct net_device *) data;
	struct gfar_private *priv = netdev_priv(dev);

	schedule_work(&priv->tq);

	mod_timer(&priv->phy_info_timer, jiffies +
			GFAR_PHY_CHANGE_TIME * HZ);
}

/* Keep trying aneg for some time
 * If, after GFAR_AN_TIMEOUT seconds, it has not
 * finished, we switch to forced.
 * Either way, once the process has completed, we either
 * request the interrupt, or switch the timer over to 
 * using gfar_phy_timer to check status */
static void gfar_phy_startup_timer(unsigned long data)
{
	int result;
	static int secondary = GFAR_AN_TIMEOUT;
	struct gfar_mii_info *mii_info = (struct gfar_mii_info *)data;
	struct gfar_private *priv = netdev_priv(mii_info->dev);

	/* Configure the Auto-negotiation */
	result = mii_info->phyinfo->config_aneg(mii_info);

	/* If autonegotiation failed to start, and
	 * we haven't timed out, reset the timer, and return */
	if (result && secondary--) {
		mod_timer(&priv->phy_info_timer, jiffies + HZ);
		return;
	} else if (result) {
		/* Couldn't start autonegotiation.
		 * Try switching to forced */
		mii_info->autoneg = 0;
		result = mii_info->phyinfo->config_aneg(mii_info);

		/* Forcing failed!  Give up */
		if(result) {
			printk(KERN_ERR "%s: Forcing failed!\n",
					mii_info->dev->name);
			return;
		}
	}

	/* Kill the timer so it can be restarted */
	del_timer_sync(&priv->phy_info_timer);

	/* Grab the PHY interrupt, if necessary/possible */
	if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
		if (request_irq(priv->einfo->interruptPHY, 
					phy_interrupt,
					SA_SHIRQ, 
					"phy_interrupt", 
					mii_info->dev) < 0) {
			printk(KERN_ERR "%s: Can't get IRQ %d (PHY)\n",
					mii_info->dev->name,
					priv->einfo->interruptPHY);
		} else {
			mii_configure_phy_interrupt(priv->mii_info, 
					MII_INTERRUPT_ENABLED);
			return;
		}
	}

	/* Start the timer again, this time in order to
	 * handle a change in status */
	init_timer(&priv->phy_info_timer);
	priv->phy_info_timer.function = &gfar_phy_timer;
	priv->phy_info_timer.data = (unsigned long) mii_info->dev;
	mod_timer(&priv->phy_info_timer, jiffies +
			GFAR_PHY_CHANGE_TIME * HZ);
}

/* Called every time the controller might need to be made
 * aware of new link state.  The PHY code conveys this
 * information through variables in the priv structure, and this
 * function converts those variables into the appropriate
 * register values, and can bring down the device if needed.
 */
static void adjust_link(struct net_device *dev)
{
	struct gfar_private *priv = netdev_priv(dev);
	struct gfar *regs = priv->regs;
	u32 tempval;
	struct gfar_mii_info *mii_info = priv->mii_info;

	if (mii_info->link) {
		/* Now we make sure that we can be in full duplex mode.
		 * If not, we operate in half-duplex mode. */
		if (mii_info->duplex != priv->oldduplex) {
			if (!(mii_info->duplex)) {
				tempval = gfar_read(&regs->maccfg2);
				tempval &= ~(MACCFG2_FULL_DUPLEX);
				gfar_write(&regs->maccfg2, tempval);

				printk(KERN_INFO "%s: Half Duplex\n",
				       dev->name);
			} else {
				tempval = gfar_read(&regs->maccfg2);
				tempval |= MACCFG2_FULL_DUPLEX;
				gfar_write(&regs->maccfg2, tempval);

				printk(KERN_INFO "%s: Full Duplex\n",
				       dev->name);
			}

			priv->oldduplex = mii_info->duplex;
		}

		if (mii_info->speed != priv->oldspeed) {
			switch (mii_info->speed) {
			case 1000:
				tempval = gfar_read(&regs->maccfg2);
				tempval =
				    ((tempval & ~(MACCFG2_IF)) | MACCFG2_GMII);
				gfar_write(&regs->maccfg2, tempval);
				break;
			case 100:
			case 10:
				tempval = gfar_read(&regs->maccfg2);
				tempval =
				    ((tempval & ~(MACCFG2_IF)) | MACCFG2_MII);
				gfar_write(&regs->maccfg2, tempval);
				break;
			default:
				printk(KERN_WARNING
				       "%s: Ack!  Speed (%d) is not 10/100/1000!\n",
				       dev->name, mii_info->speed);
				break;
			}

			printk(KERN_INFO "%s: Speed %dBT\n", dev->name,
			       mii_info->speed);

			priv->oldspeed = mii_info->speed;
		}

		if (!priv->oldlink) {
			printk(KERN_INFO "%s: Link is up\n", dev->name);
			priv->oldlink = 1;
			netif_carrier_on(dev);
			netif_schedule(dev);
		}
	} else {
		if (priv->oldlink) {
			printk(KERN_INFO "%s: Link is down\n", dev->name);
			priv->oldlink = 0;
			priv->oldspeed = 0;
			priv->oldduplex = -1;
			netif_carrier_off(dev);
		}
	}
}


/* Update the hash table based on the current list of multicast
 * addresses we subscribe to.  Also, change the promiscuity of
 * the device based on the flags (this function is called
 * whenever dev->flags is changed */
static void gfar_set_multi(struct net_device *dev)
{
	struct dev_mc_list *mc_ptr;
	struct gfar_private *priv = netdev_priv(dev);
	struct gfar *regs = priv->regs;
	u32 tempval;

	if(dev->flags & IFF_PROMISC) {
		printk(KERN_INFO "%s: Entering promiscuous mode.\n",
				dev->name);
		/* Set RCTRL to PROM */
		tempval = gfar_read(&regs->rctrl);
		tempval |= RCTRL_PROM;
		gfar_write(&regs->rctrl, tempval);
	} else {
		/* Set RCTRL to not PROM */
		tempval = gfar_read(&regs->rctrl);
		tempval &= ~(RCTRL_PROM);
		gfar_write(&regs->rctrl, tempval);
	}
	
	if(dev->flags & IFF_ALLMULTI) {
		/* Set the hash to rx all multicast frames */
		gfar_write(&regs->gaddr0, 0xffffffff);
		gfar_write(&regs->gaddr1, 0xffffffff);
		gfar_write(&regs->gaddr2, 0xffffffff);
		gfar_write(&regs->gaddr3, 0xffffffff);
		gfar_write(&regs->gaddr4, 0xffffffff);
		gfar_write(&regs->gaddr5, 0xffffffff);
		gfar_write(&regs->gaddr6, 0xffffffff);
		gfar_write(&regs->gaddr7, 0xffffffff);
	} else {
		/* zero out the hash */
		gfar_write(&regs->gaddr0, 0x0);
		gfar_write(&regs->gaddr1, 0x0);
		gfar_write(&regs->gaddr2, 0x0);
		gfar_write(&regs->gaddr3, 0x0);
		gfar_write(&regs->gaddr4, 0x0);
		gfar_write(&regs->gaddr5, 0x0);
		gfar_write(&regs->gaddr6, 0x0);
		gfar_write(&regs->gaddr7, 0x0);

		if(dev->mc_count == 0)
			return;

		/* Parse the list, and set the appropriate bits */
		for(mc_ptr = dev->mc_list; mc_ptr; mc_ptr = mc_ptr->next) {
			gfar_set_hash_for_addr(dev, mc_ptr->dmi_addr);
		}
	}

	return;
}

/* Set the appropriate hash bit for the given addr */
/* The algorithm works like so:
 * 1) Take the Destination Address (ie the multicast address), and
 * do a CRC on it (little endian), and reverse the bits of the
 * result.
 * 2) Use the 8 most significant bits as a hash into a 256-entry
 * table.  The table is controlled through 8 32-bit registers:
 * gaddr0-7.  gaddr0's MSB is entry 0, and gaddr7's LSB is
 * gaddr7.  This means that the 3 most significant bits in the
 * hash index which gaddr register to use, and the 5 other bits
 * indicate which bit (assuming an IBM numbering scheme, which
 * for PowerPC (tm) is usually the case) in the register holds
 * the entry. */
static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr)
{
	u32 tempval;
	struct gfar_private *priv = netdev_priv(dev);
	struct gfar *regs = priv->regs;
	u32 *hash = &regs->gaddr0;
	u32 result = ether_crc(MAC_ADDR_LEN, addr);
	u8 whichreg = ((result >> 29) & 0x7);
	u8 whichbit = ((result >> 24) & 0x1f);
	u32 value = (1 << (31-whichbit));

	tempval = gfar_read(&hash[whichreg]);
	tempval |= value;
	gfar_write(&hash[whichreg], tempval);

	return;
}

/* GFAR error interrupt handler */
static irqreturn_t gfar_error(int irq, void *dev_id, struct pt_regs *regs)
{
	struct net_device *dev = dev_id;
	struct gfar_private *priv = netdev_priv(dev);

	/* Save ievent for future reference */
	u32 events = gfar_read(&priv->regs->ievent);

	/* Clear IEVENT */
	gfar_write(&priv->regs->ievent, IEVENT_ERR_MASK);

	/* Hmm... */
#if defined (BRIEF_GFAR_ERRORS) || defined (VERBOSE_GFAR_ERRORS)
	printk(KERN_DEBUG "%s: error interrupt (ievent=0x%08x imask=0x%08x)\n",
	       dev->name, events, gfar_read(&priv->regs->imask));
#endif

	/* Update the error counters */
	if (events & IEVENT_TXE) {
		priv->stats.tx_errors++;

		if (events & IEVENT_LC)
			priv->stats.tx_window_errors++;
		if (events & IEVENT_CRL)
			priv->stats.tx_aborted_errors++;
		if (events & IEVENT_XFUN) {
#ifdef VERBOSE_GFAR_ERRORS
			printk(KERN_DEBUG "%s: underrun.  packet dropped.\n",
			       dev->name);
#endif
			priv->stats.tx_dropped++;
			priv->extra_stats.tx_underrun++;

			/* Reactivate the Tx Queues */
			gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT);
		}
#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: Transmit Error\n", dev->name);
#endif
	}
	if (events & IEVENT_BSY) {
		priv->stats.rx_errors++;
		priv->extra_stats.rx_bsy++;

		gfar_receive(irq, dev_id, regs);

#ifndef CONFIG_GFAR_NAPI
		/* Clear the halt bit in RSTAT */
		gfar_write(&priv->regs->rstat, RSTAT_CLEAR_RHALT);
#endif

#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: busy error (rhalt: %x)\n", dev->name,
		       gfar_read(&priv->regs->rstat));
#endif
	}
	if (events & IEVENT_BABR) {
		priv->stats.rx_errors++;
		priv->extra_stats.rx_babr++;

#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: babbling error\n", dev->name);
#endif
	}
	if (events & IEVENT_EBERR) {
		priv->extra_stats.eberr++;
#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: EBERR\n", dev->name);
#endif
	}
	if (events & IEVENT_RXC)
#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: control frame\n", dev->name);
#endif

	if (events & IEVENT_BABT) {
		priv->extra_stats.tx_babt++;
#ifdef VERBOSE_GFAR_ERRORS
		printk(KERN_DEBUG "%s: babt error\n", dev->name);
#endif
	}
	return IRQ_HANDLED;
}

/* Structure for a device driver */
static struct device_driver gfar_driver = {
	.name = "fsl-gianfar",
	.bus = &platform_bus_type,
	.probe = gfar_probe,
	.remove = gfar_remove,
};

static int __init gfar_init(void)
{
	return driver_register(&gfar_driver);
}

static void __exit gfar_exit(void)
{
	driver_unregister(&gfar_driver);
}

module_init(gfar_init);
module_exit(gfar_exit);