blob: e552b8d68450c895fb65733645da297a1246ee2d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
|
/*
* auxio.h: Definitions and code for the Auxiliary I/O register.
*
* Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
*/
#ifndef _SPARC_AUXIO_H
#define _SPARC_AUXIO_H
#include <asm/system.h>
#include <asm/vaddrs.h>
/* This register is an unsigned char in IO space. It does two things.
* First, it is used to control the front panel LED light on machines
* that have it (good for testing entry points to trap handlers and irq's)
* Secondly, it controls various floppy drive parameters.
*/
#define AUXIO_ORMEIN 0xf0 /* All writes must set these bits. */
#define AUXIO_ORMEIN4M 0xc0 /* sun4m - All writes must set these bits. */
#define AUXIO_FLPY_DENS 0x20 /* Floppy density, high if set. Read only. */
#define AUXIO_FLPY_DCHG 0x10 /* A disk change occurred. Read only. */
#define AUXIO_EDGE_ON 0x10 /* sun4m - On means Jumper block is in. */
#define AUXIO_FLPY_DSEL 0x08 /* Drive select/start-motor. Write only. */
#define AUXIO_LINK_TEST 0x08 /* sun4m - On means TPE Carrier detect. */
/* Set the following to one, then zero, after doing a pseudo DMA transfer. */
#define AUXIO_FLPY_TCNT 0x04 /* Floppy terminal count. Write only. */
/* Set the following to zero to eject the floppy. */
#define AUXIO_FLPY_EJCT 0x02 /* Eject floppy disk. Write only. */
#define AUXIO_LED 0x01 /* On if set, off if unset. Read/Write */
#ifndef __ASSEMBLY__
/*
* NOTE: these routines are implementation dependent--
* understand the hardware you are querying!
*/
extern void set_auxio(unsigned char bits_on, unsigned char bits_off);
extern unsigned char get_auxio(void); /* .../asm-sparc/floppy.h */
/*
* The following routines are provided for driver-compatibility
* with sparc64 (primarily sunlance.c)
*/
#define AUXIO_LTE_ON 1
#define AUXIO_LTE_OFF 0
/* auxio_set_lte - Set Link Test Enable (TPE Link Detect)
*
* on - AUXIO_LTE_ON or AUXIO_LTE_OFF
*/
#define auxio_set_lte(on) \
do { \
if(on) { \
set_auxio(AUXIO_LINK_TEST, 0); \
} else { \
set_auxio(0, AUXIO_LINK_TEST); \
} \
} while (0)
#define AUXIO_LED_ON 1
#define AUXIO_LED_OFF 0
/* auxio_set_led - Set system front panel LED
*
* on - AUXIO_LED_ON or AUXIO_LED_OFF
*/
#define auxio_set_led(on) \
do { \
if(on) { \
set_auxio(AUXIO_LED, 0); \
} else { \
set_auxio(0, AUXIO_LED); \
} \
} while (0)
#endif /* !(__ASSEMBLY__) */
/* AUXIO2 (Power Off Control) */
extern __volatile__ unsigned char * auxio_power_register;
#define AUXIO_POWER_DETECT_FAILURE 32
#define AUXIO_POWER_CLEAR_FAILURE 2
#define AUXIO_POWER_OFF 1
#endif /* !(_SPARC_AUXIO_H) */
|
