1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
|
/*
* AD9523 SPI Low Jitter Clock Generator
*
* Copyright 2012 Analog Devices Inc.
*
* Licensed under the GPL-2.
*/
#ifndef IIO_FREQUENCY_AD9523_H_
#define IIO_FREQUENCY_AD9523_H_
enum outp_drv_mode {
TRISTATE,
LVPECL_8mA,
LVDS_4mA,
LVDS_7mA,
HSTL0_16mA,
HSTL1_8mA,
CMOS_CONF1,
CMOS_CONF2,
CMOS_CONF3,
CMOS_CONF4,
CMOS_CONF5,
CMOS_CONF6,
CMOS_CONF7,
CMOS_CONF8,
CMOS_CONF9
};
enum ref_sel_mode {
NONEREVERTIVE_STAY_ON_REFB,
REVERT_TO_REFA,
SELECT_REFA,
SELECT_REFB,
EXT_REF_SEL
};
/**
* struct ad9523_channel_spec - Output channel configuration
*
* @channel_num: Output channel number.
* @divider_output_invert_en: Invert the polarity of the output clock.
* @sync_ignore_en: Ignore chip-level SYNC signal.
* @low_power_mode_en: Reduce power used in the differential output modes.
* @use_alt_clock_src: Channel divider uses alternative clk source.
* @output_dis: Disables, powers down the entire channel.
* @driver_mode: Output driver mode (logic level family).
* @divider_phase: Divider initial phase after a SYNC. Range 0..63
LSB = 1/2 of a period of the divider input clock.
* @channel_divider: 10-bit channel divider.
* @extended_name: Optional descriptive channel name.
*/
struct ad9523_channel_spec {
unsigned channel_num;
bool divider_output_invert_en;
bool sync_ignore_en;
bool low_power_mode_en;
/* CH0..CH3 VCXO, CH4..CH9 VCO2 */
bool use_alt_clock_src;
bool output_dis;
enum outp_drv_mode driver_mode;
unsigned char divider_phase;
unsigned short channel_divider;
char extended_name[16];
};
enum pll1_rzero_resistor {
RZERO_883_OHM,
RZERO_677_OHM,
RZERO_341_OHM,
RZERO_135_OHM,
RZERO_10_OHM,
RZERO_USE_EXT_RES = 8,
};
enum rpole2_resistor {
RPOLE2_900_OHM,
RPOLE2_450_OHM,
RPOLE2_300_OHM,
RPOLE2_225_OHM,
};
enum rzero_resistor {
RZERO_3250_OHM,
RZERO_2750_OHM,
RZERO_2250_OHM,
RZERO_2100_OHM,
RZERO_3000_OHM,
RZERO_2500_OHM,
RZERO_2000_OHM,
RZERO_1850_OHM,
};
enum cpole1_capacitor {
CPOLE1_0_PF,
CPOLE1_8_PF,
CPOLE1_16_PF,
CPOLE1_24_PF,
_CPOLE1_24_PF, /* place holder */
CPOLE1_32_PF,
CPOLE1_40_PF,
CPOLE1_48_PF,
};
/**
* struct ad9523_platform_data - platform specific information
*
* @vcxo_freq: External VCXO frequency in Hz
* @refa_diff_rcv_en: REFA differential/single-ended input selection.
* @refb_diff_rcv_en: REFB differential/single-ended input selection.
* @zd_in_diff_en: Zero Delay differential/single-ended input selection.
* @osc_in_diff_en: OSC differential/ single-ended input selection.
* @refa_cmos_neg_inp_en: REFA single-ended neg./pos. input enable.
* @refb_cmos_neg_inp_en: REFB single-ended neg./pos. input enable.
* @zd_in_cmos_neg_inp_en: Zero Delay single-ended neg./pos. input enable.
* @osc_in_cmos_neg_inp_en: OSC single-ended neg./pos. input enable.
* @refa_r_div: PLL1 10-bit REFA R divider.
* @refb_r_div: PLL1 10-bit REFB R divider.
* @pll1_feedback_div: PLL1 10-bit Feedback N divider.
* @pll1_charge_pump_current_nA: Magnitude of PLL1 charge pump current (nA).
* @zero_delay_mode_internal_en: Internal, external Zero Delay mode selection.
* @osc_in_feedback_en: PLL1 feedback path, local feedback from
* the OSC_IN receiver or zero delay mode
* @pll1_loop_filter_rzero: PLL1 Loop Filter Zero Resistor selection.
* @ref_mode: Reference selection mode.
* @pll2_charge_pump_current_nA: Magnitude of PLL2 charge pump current (nA).
* @pll2_ndiv_a_cnt: PLL2 Feedback N-divider, A Counter, range 0..4.
* @pll2_ndiv_b_cnt: PLL2 Feedback N-divider, B Counter, range 0..63.
* @pll2_freq_doubler_en: PLL2 frequency doubler enable.
* @pll2_r2_div: PLL2 R2 divider, range 0..31.
* @pll2_vco_diff_m1: VCO1 divider, range 3..5.
* @pll2_vco_diff_m2: VCO2 divider, range 3..5.
* @rpole2: PLL2 loop filter Rpole resistor value.
* @rzero: PLL2 loop filter Rzero resistor value.
* @cpole1: PLL2 loop filter Cpole capacitor value.
* @rzero_bypass_en: PLL2 loop filter Rzero bypass enable.
* @num_channels: Array size of struct ad9523_channel_spec.
* @channels: Pointer to channel array.
* @name: Optional alternative iio device name.
*/
struct ad9523_platform_data {
unsigned long vcxo_freq;
/* Differential/ Single-Ended Input Configuration */
bool refa_diff_rcv_en;
bool refb_diff_rcv_en;
bool zd_in_diff_en;
bool osc_in_diff_en;
/*
* Valid if differential input disabled
* if false defaults to pos input
*/
bool refa_cmos_neg_inp_en;
bool refb_cmos_neg_inp_en;
bool zd_in_cmos_neg_inp_en;
bool osc_in_cmos_neg_inp_en;
/* PLL1 Setting */
unsigned short refa_r_div;
unsigned short refb_r_div;
unsigned short pll1_feedback_div;
unsigned short pll1_charge_pump_current_nA;
bool zero_delay_mode_internal_en;
bool osc_in_feedback_en;
enum pll1_rzero_resistor pll1_loop_filter_rzero;
/* Reference */
enum ref_sel_mode ref_mode;
/* PLL2 Setting */
unsigned int pll2_charge_pump_current_nA;
unsigned char pll2_ndiv_a_cnt;
unsigned char pll2_ndiv_b_cnt;
bool pll2_freq_doubler_en;
unsigned char pll2_r2_div;
unsigned char pll2_vco_diff_m1; /* 3..5 */
unsigned char pll2_vco_diff_m2; /* 3..5 */
/* Loop Filter PLL2 */
enum rpole2_resistor rpole2;
enum rzero_resistor rzero;
enum cpole1_capacitor cpole1;
bool rzero_bypass_en;
/* Output Channel Configuration */
int num_channels;
struct ad9523_channel_spec *channels;
char name[SPI_NAME_SIZE];
};
#endif /* IIO_FREQUENCY_AD9523_H_ */
|
