diff options
| author | Simon Vincent <simon.vincent@xsilon.com> | 2014-10-06 10:39:45 +0100 |
|---|---|---|
| committer | Marcel Holtmann <marcel@holtmann.org> | 2014-10-25 07:56:22 +0200 |
| commit | db9e0ee805901c4a7284fde1f12a8033f24d2e07 (patch) | |
| tree | cb80d2193ffba69d755089e43d5f7bdd845d99f4 | |
| parent | 4b552bc9edfdc947862af225a0e2521edb5d37a0 (diff) | |
ieee802154: mrf24j40: Add support for MRF24J40MC
The MRF24J40MC module has an external amplifier which should be
enabled. The TX power has to be lowered to meet FCC regs.
Signed-off-by: Simon Vincent <simon.vincent@xsilon.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
| -rw-r--r-- | drivers/net/ieee802154/mrf24j40.c | 32 |
1 files changed, 30 insertions, 2 deletions
diff --git a/drivers/net/ieee802154/mrf24j40.c b/drivers/net/ieee802154/mrf24j40.c index 07e0b887c35..b1e73bc6e39 100644 --- a/drivers/net/ieee802154/mrf24j40.c +++ b/drivers/net/ieee802154/mrf24j40.c @@ -43,6 +43,8 @@ #define REG_TXSTBL 0x2E /* TX Stabilization */ #define REG_INTSTAT 0x31 /* Interrupt Status */ #define REG_INTCON 0x32 /* Interrupt Control */ +#define REG_GPIO 0x33 /* GPIO */ +#define REG_TRISGPIO 0x34 /* GPIO direction */ #define REG_RFCTL 0x36 /* RF Control Mode Register */ #define REG_BBREG1 0x39 /* Baseband Registers */ #define REG_BBREG2 0x3A /* */ @@ -63,6 +65,7 @@ #define REG_SLPCON1 0x220 #define REG_WAKETIMEL 0x222 /* Wake-up Time Match Value Low */ #define REG_WAKETIMEH 0x223 /* Wake-up Time Match Value High */ +#define REG_TESTMODE 0x22F /* Test mode */ #define REG_RX_FIFO 0x300 /* Receive FIFO */ /* Device configuration: Only channels 11-26 on page 0 are supported. */ @@ -75,6 +78,8 @@ #define RX_FIFO_SIZE 144 /* From datasheet */ #define SET_CHANNEL_DELAY_US 192 /* From datasheet */ +enum mrf24j40_modules { MRF24J40, MRF24J40MA, MRF24J40MC }; + /* Device Private Data */ struct mrf24j40 { struct spi_device *spi; @@ -691,6 +696,28 @@ static int mrf24j40_hw_init(struct mrf24j40 *devrec) if (ret) goto err_ret; + if (spi_get_device_id(devrec->spi)->driver_data == MRF24J40MC) { + /* Enable external amplifier. + * From MRF24J40MC datasheet section 1.3: Operation. + */ + read_long_reg(devrec, REG_TESTMODE, &val); + val |= 0x7; /* Configure GPIO 0-2 to control amplifier */ + write_long_reg(devrec, REG_TESTMODE, val); + + read_short_reg(devrec, REG_TRISGPIO, &val); + val |= 0x8; /* Set GPIO3 as output. */ + write_short_reg(devrec, REG_TRISGPIO, val); + + read_short_reg(devrec, REG_GPIO, &val); + val |= 0x8; /* Set GPIO3 HIGH to enable U5 voltage regulator */ + write_short_reg(devrec, REG_GPIO, val); + + /* Reduce TX pwr to meet FCC requirements. + * From MRF24J40MC datasheet section 3.1.1 + */ + write_long_reg(devrec, REG_RFCON3, 0x28); + } + return 0; err_ret: @@ -779,8 +806,9 @@ static int mrf24j40_remove(struct spi_device *spi) } static const struct spi_device_id mrf24j40_ids[] = { - { "mrf24j40", 0 }, - { "mrf24j40ma", 0 }, + { "mrf24j40", MRF24J40 }, + { "mrf24j40ma", MRF24J40MA }, + { "mrf24j40mc", MRF24J40MC }, { }, }; MODULE_DEVICE_TABLE(spi, mrf24j40_ids); |