Merge tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into next

Pull USB driver updates from Greg KH:
 "Here is the big USB driver pull request for 3.16-rc1.

  Nothing huge here, but lots of little things in the USB core, and in
  lots of drivers.  Hopefully the USB power management will be work
  better now that it has been reworked to do per-port power control
  dynamically.  There's also a raft of gadget driver updates and fixes,
  CONFIG_USB_DEBUG is finally gone now that everything has been
  converted over to the dynamic debug inteface, the last hold-out
  drivers were cleaned up and the config option removed.  There were
  also other minor things all through the drivers/usb/ tree, the
  shortlog shows this pretty well.

  All have been in linux-next, including the very last patch, which came
  from linux-next to fix a build issue on some platforms"

* tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (314 commits)
  usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
  USB: orinoco_usb: remove CONFIG_USB_DEBUG support
  USB: media: lirc: igorplugusb: remove CONFIG_USB_DEBUG support
  USB: media: streamzap: remove CONFIG_USB_DEBUG
  USB: media: redrat3: remove CONFIG_USB_DEBUG usage
  USB: media: redrat3: remove unneeded tracing macro
  usb: qcserial: add additional Sierra Wireless QMI devices
  usb: host: max3421-hcd: Use module_spi_driver
  usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
  usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
  usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
  usb: qcserial: add Netgear AirCard 341U
  Documentation: dt-bindings: update xhci-platform DT binding for R-Car H2 and M2
  usb: host: xhci-plat: add xhci_plat_start()
  usb: host: max3421-hcd: Fix potential NULL urb dereference
  Revert "usb: gadget: net2280: Add support for PLX USB338X"
  USB: usbip: remove CONFIG_USB_DEBUG reference
  USB: remove CONFIG_USB_DEBUG from defconfig files
  usb: resume child device when port is powered on
  usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
  ...

1 files changed, 8 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt
index a018da4a7ad..221ac0dbc67 100644
--- a/Documentation/devicetree/bindings/usb/usb3503.txt
+++ b/Documentation/devicetree/bindings/usb/usb3503.txt
@@ -15,6 +15,14 @@ Optional properties:
 - reset-gpios: Should specify GPIO for reset.
 - initial-mode: Should specify initial mode.
                 (1 for HUB mode, 2 for STANDBY mode)
+- refclk: Clock used for driving REFCLK signal (optional, if not provided
+	the driver assumes that clock signal is always available, its
+	rate is specified by REF_SEL pins and a value from the primary
+	reference clock frequencies table is used)
+- refclk-frequency: Frequency of the REFCLK signal as defined by REF_SEL
+	pins (optional, if not provided, driver will not set rate of the
+	REFCLK signal and assume that a value from the primary reference
+	clock frequencies table is used)
 
 Examples:
 	usb3503@08 {