diff options
| author | Ingo Molnar <mingo@elte.hu> | 2011-02-16 13:33:35 +0100 |
|---|---|---|
| committer | Ingo Molnar <mingo@elte.hu> | 2011-02-16 13:33:41 +0100 |
| commit | a3ec4a603faf4244e275bf11b467aad092dfbd8a (patch) | |
| tree | 1c15009716b37629070ea221a00eb9fe2303a317 /Documentation/devicetree/bindings | |
| parent | 51563cd53c4b1c1790fccd2e0af0e2b756589af9 (diff) | |
| parent | 85e2efbb1db9a18d218006706d6e4fbeb0216213 (diff) | |
Merge commit 'v2.6.38-rc5' into core/locking
Merge reason: pick up upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Diffstat (limited to 'Documentation/devicetree/bindings')
59 files changed, 4107 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/ata/fsl-sata.txt b/Documentation/devicetree/bindings/ata/fsl-sata.txt new file mode 100644 index 00000000000..b46bcf46c3d --- /dev/null +++ b/Documentation/devicetree/bindings/ata/fsl-sata.txt @@ -0,0 +1,29 @@ +* Freescale 8xxx/3.0 Gb/s SATA nodes + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA port should have its own node. + +Required properties: +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-sata", where CHIP is the processor + (mpc8315, mpc8379, etc.) and the second is + "fsl,pq-sata" +- interrupts : <interrupt mapping for SATA IRQ> +- cell-index : controller index. + 1 for controller @ 0x18000 + 2 for controller @ 0x19000 + 3 for controller @ 0x1a000 + 4 for controller @ 0x1b000 + +Optional properties: +- interrupt-parent : optional, if needed for interrupt mapping +- reg : <registers mapping> + +Example: + sata@18000 { + compatible = "fsl,mpc8379-sata", "fsl,pq-sata"; + reg = <0x18000 0x1000>; + cell-index = <1>; + interrupts = <2c 8>; + interrupt-parent = < &ipic >; + }; diff --git a/Documentation/devicetree/bindings/eeprom.txt b/Documentation/devicetree/bindings/eeprom.txt new file mode 100644 index 00000000000..4342c10de1b --- /dev/null +++ b/Documentation/devicetree/bindings/eeprom.txt @@ -0,0 +1,28 @@ +EEPROMs (I2C) + +Required properties: + + - compatible : should be "<manufacturer>,<type>" + If there is no specific driver for <manufacturer>, a generic + driver based on <type> is selected. Possible types are: + 24c00, 24c01, 24c02, 24c04, 24c08, 24c16, 24c32, 24c64, + 24c128, 24c256, 24c512, 24c1024, spd + + - reg : the I2C address of the EEPROM + +Optional properties: + + - pagesize : the length of the pagesize for writing. Please consult the + manual of your device, that value varies a lot. A wrong value + may result in data loss! If not specified, a safety value of + '1' is used which will be very slow. + + - read-only: this parameterless property disables writes to the eeprom + +Example: + +eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; +}; diff --git a/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt new file mode 100644 index 00000000000..b0019eb5330 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt @@ -0,0 +1,60 @@ +GPIO controllers on MPC8xxx SoCs + +This is for the non-QE/CPM/GUTs GPIO controllers as found on +8349, 8572, 8610 and compatible. + +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +Required properties: +- compatible : "fsl,<CHIP>-gpio" followed by "fsl,mpc8349-gpio" for + 83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + - interrupts : Interrupt mapping for GPIO IRQ. + - interrupt-parent : Phandle for the interrupt controller that + services interrupts for this device. +- gpio-controller : Marks the port as GPIO controller. + +Example of gpio-controller nodes for a MPC8347 SoC: + + gpio1: gpio-controller@c00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xc00 0x100>; + interrupts = <74 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + }; + + gpio2: gpio-controller@d00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xd00 0x100>; + interrupts = <75 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + }; + +See booting-without-of.txt for details of how to specify GPIO +information for devices. + +To use GPIO pins as interrupt sources for peripherals, specify the +GPIO controller as the interrupt parent and define GPIO number + +trigger mode using the interrupts property, which is defined like +this: + +interrupts = <number trigger>, where: + - number: GPIO pin (0..31) + - trigger: trigger mode: + 2 = trigger on falling edge + 3 = trigger on both edges + +Example of device using this is: + + funkyfpga@0 { + compatible = "funky-fpga"; + ... + interrupts = <4 3>; + interrupt-parent = <&gpio1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt new file mode 100644 index 00000000000..edaa84d288a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -0,0 +1,50 @@ +Specifying GPIO information for devices +============================================ + +1) gpios property +----------------- + +Nodes that makes use of GPIOs should define them using `gpios' property, +format of which is: <&gpio-controller1-phandle gpio1-specifier + &gpio-controller2-phandle gpio2-specifier + 0 /* holes are permitted, means no GPIO 3 */ + &gpio-controller4-phandle gpio4-specifier + ...>; + +Note that gpio-specifier length is controller dependent. + +gpio-specifier may encode: bank, pin position inside the bank, +whether pin is open-drain and whether pin is logically inverted. + +Example of the node using GPIOs: + + node { + gpios = <&qe_pio_e 18 0>; + }; + +In this example gpio-specifier is "18 0" and encodes GPIO pin number, +and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. + +2) gpio-controller nodes +------------------------ + +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +Example of two SOC GPIO banks defined as gpio-controller nodes: + + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; + + diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt new file mode 100644 index 00000000000..064db928c3c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -0,0 +1,58 @@ +LEDs connected to GPIO lines + +Required properties: +- compatible : should be "gpio-leds". + +Each LED is represented as a sub-node of the gpio-leds device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: +- gpios : Should specify the LED's GPIO, see "Specifying GPIO information + for devices" in Documentation/powerpc/booting-without-of.txt. Active + low LEDs should be indicated using flags in the GPIO specifier. +- label : (optional) The label for this LED. If omitted, the label is + taken from the node name (excluding the unit address). +- linux,default-trigger : (optional) This parameter, if present, is a + string defining the trigger assigned to the LED. Current triggers are: + "backlight" - LED will act as a back-light, controlled by the framebuffer + system + "default-on" - LED will turn on, but see "default-state" below + "heartbeat" - LED "double" flashes at a load average based rate + "ide-disk" - LED indicates disk activity + "timer" - LED flashes at a fixed, configurable rate +- default-state: (optional) The initial state of the LED. Valid + values are "on", "off", and "keep". If the LED is already on or off + and the default-state property is set the to same value, then no + glitch should be produced where the LED momentarily turns off (or + on). The "keep" setting will keep the LED at whatever its current + state is, without producing a glitch. The default is off if this + property is not present. + +Examples: + +leds { + compatible = "gpio-leds"; + hdd { + label = "IDE Activity"; + gpios = <&mcu_pio 0 1>; /* Active low */ + linux,default-trigger = "ide-disk"; + }; + + fault { + gpios = <&mcu_pio 1 0>; + /* Keep LED on if BIOS detected hardware fault */ + default-state = "keep"; + }; +}; + +run-control { + compatible = "gpio-leds"; + red { + gpios = <&mpc8572 6 0>; + default-state = "off"; + }; + green { + gpios = <&mpc8572 7 0>; + default-state = "on"; + }; +} diff --git a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt b/Documentation/devicetree/bindings/i2c/fsl-i2c.txt new file mode 100644 index 00000000000..1eacd6b20ed --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/fsl-i2c.txt @@ -0,0 +1,64 @@ +* I2C + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a + compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121, + mpc5200 or mpc5200b. For the mpc5121, an additional node + "fsl,mpc5121-i2c-ctrl" is required as shown in the example below. + +Recommended properties : + + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - fsl,preserve-clocking : boolean; if defined, the clock settings + from the bootloader are preserved (not touched). + - clock-frequency : desired I2C bus clock frequency in Hz. + - fsl,timeout : I2C bus timeout in microseconds. + +Examples : + + /* MPC5121 based board */ + i2c@1740 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5121-i2c", "fsl-i2c"; + reg = <0x1740 0x20>; + interrupts = <11 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <100000>; + }; + + i2ccontrol@1760 { + compatible = "fsl,mpc5121-i2c-ctrl"; + reg = <0x1760 0x8>; + }; + + /* MPC5200B based board */ + i2c@3d00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; + reg = <0x3d00 0x40>; + interrupts = <2 15 0>; + interrupt-parent = <&mpc5200_pic>; + fsl,preserve-clocking; + }; + + /* MPC8544 base board */ + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc8544-i2c", "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + clock-frequency = <400000>; + fsl,timeout = <10000>; + }; diff --git a/Documentation/devicetree/bindings/marvell.txt b/Documentation/devicetree/bindings/marvell.txt new file mode 100644 index 00000000000..f1533d91953 --- /dev/null +++ b/Documentation/devicetree/bindings/marvell.txt @@ -0,0 +1,521 @@ +Marvell Discovery mv64[345]6x System Controller chips +=========================================================== + +The Marvell mv64[345]60 series of system controller chips contain +many of the peripherals needed to implement a complete computer +system. In this section, we define device tree nodes to describe +the system controller chip itself and each of the peripherals +which it contains. Compatible string values for each node are +prefixed with the string "marvell,", for Marvell Technology Group Ltd. + +1) The /system-controller node + + This node is used to represent the system-controller and must be + present when the system uses a system controller chip. The top-level + system-controller node contains information that is global to all + devices within the system controller chip. The node name begins + with "system-controller" followed by the unit address, which is + the base address of the memory-mapped register set for the system + controller chip. + + Required properties: + + - ranges : Describes the translation of system controller addresses + for memory mapped registers. + - clock-frequency: Contains the main clock frequency for the system + controller chip. + - reg : This property defines the address and size of the + memory-mapped registers contained within the system controller + chip. The address specified in the "reg" property should match + the unit address of the system-controller node. + - #address-cells : Address representation for system controller + devices. This field represents the number of cells needed to + represent the address of the memory-mapped registers of devices + within the system controller chip. + - #size-cells : Size representation for the memory-mapped + registers within the system controller chip. + - #interrupt-cells : Defines the width of cells used to represent + interrupts. + + Optional properties: + + - model : The specific model of the system controller chip. Such + as, "mv64360", "mv64460", or "mv64560". + - compatible : A string identifying the compatibility identifiers + of the system controller chip. + + The system-controller node contains child nodes for each system + controller device that the platform uses. Nodes should not be created + for devices which exist on the system controller chip but are not used + + Example Marvell Discovery mv64360 system-controller node: + + system-controller@f1000000 { /* Marvell Discovery mv64360 */ + #address-cells = <1>; + #size-cells = <1>; + model = "mv64360"; /* Default */ + compatible = "marvell,mv64360"; + clock-frequency = <133333333>; + reg = <0xf1000000 0x10000>; + virtual-reg = <0xf1000000>; + ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */ + 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */ + 0xa0000000 0xa0000000 0x4000000 /* User FLASH */ + 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */ + 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */ + + [ child node definitions... ] + } + +2) Child nodes of /system-controller + + a) Marvell Discovery MDIO bus + + The MDIO is a bus to which the PHY devices are connected. For each + device that exists on this bus, a child node should be created. See + the definition of the PHY node below for an example of how to define + a PHY. + + Required properties: + - #address-cells : Should be <1> + - #size-cells : Should be <0> + - device_type : Should be "mdio" + - compatible : Should be "marvell,mv64360-mdio" + + Example: + + mdio { + #address-cells = <1>; + #size-cells = <0>; + device_type = "mdio"; + compatible = "marvell,mv64360-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + + + b) Marvell Discovery ethernet controller + + The Discover ethernet controller is described with two levels + of nodes. The first level describes an ethernet silicon block + and the second level describes up to 3 ethernet nodes within + that block. The reason for the multiple levels is that the + registers for the node are interleaved within a single set + of registers. The "ethernet-block" level describes the + shared register set, and the "ethernet" nodes describe ethernet + port-specific properties. + + Ethernet block node + + Required properties: + - #address-cells : <1> + - #size-cells : <0> + - compatible : "marvell,mv64360-eth-block" + - reg : Offset and length of the register set for this block + + Example Discovery Ethernet block node: + ethernet-block@2000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,mv64360-eth-block"; + reg = <0x2000 0x2000>; + ethernet@0 { + ....... + }; + }; + + Ethernet port node + + Required properties: + - device_type : Should be "network". + - compatible : Should be "marvell,mv64360-eth". + - reg : Should be <0>, <1>, or <2>, according to which registers + within the silicon block the device uses. + - interrupts : <a> where a is the interrupt number for the port. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + - phy : the phandle for the PHY connected to this ethernet + controller. + - local-mac-address : 6 bytes, MAC address + + Example Discovery Ethernet port node: + ethernet@0 { + device_type = "network"; + compatible = "marvell,mv64360-eth"; + reg = <0>; + interrupts = <32>; + interrupt-parent = <&PIC>; + phy = <&PHY0>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + + + + c) Marvell Discovery PHY nodes + + Required properties: + - device_type : Should be "ethernet-phy" + - interrupts : <a> where a is the interrupt number for this phy. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + + Example Discovery PHY node: + ethernet-phy@1 { + device_type = "ethernet-phy"; + compatible = "broadcom,bcm5421"; + interrupts = <76>; /* GPP 12 */ + interrupt-parent = <&PIC>; + reg = <1>; + }; + + + d) Marvell Discovery SDMA nodes + + Represent DMA hardware associated with the MPSC (multiprotocol + serial controllers). + + Required properties: + - compatible : "marvell,mv64360-sdma" + - reg : Offset and length of the register set for this device + - interrupts : <a> where a is the interrupt number for the DMA + device. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery SDMA node: + sdma@4000 { + compatible = "marvell,mv64360-sdma"; + reg = <0x4000 0xc18>; + virtual-reg = <0xf1004000>; + interrupts = <36>; + interrupt-parent = <&PIC>; + }; + + + e) Marvell Discovery BRG nodes + + Represent baud rate generator hardware associated with the MPSC + (multiprotocol serial controllers). + + Required properties: + - compatible : "marvell,mv64360-brg" + - reg : Offset and length of the register set for this device + - clock-src : A value from 0 to 15 which selects the clock + source for the baud rate generator. This value corresponds + to the CLKS value in the BRGx configuration register. See + the mv64x60 User's Manual. + - clock-frequence : The frequency (in Hz) of the baud rate + generator's input clock. + - current-speed : The current speed setting (presumably by + firmware) of the baud rate generator. + + Example Discovery BRG node: + brg@b200 { + compatible = "marvell,mv64360-brg"; + reg = <0xb200 0x8>; + clock-src = <8>; + clock-frequency = <133333333>; + current-speed = <9600>; + }; + + + f) Marvell Discovery CUNIT nodes + + Represent the Serial Communications Unit device hardware. + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery CUNIT node: + cunit@f200 { + reg = <0xf200 0x200>; + }; + + + g) Marvell Discovery MPSCROUTING nodes + + Represent the Discovery's MPSC routing hardware + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery CUNIT node: + mpscrouting@b500 { + reg = <0xb400 0xc>; + }; + + + h) Marvell Discovery MPSCINTR nodes + + Represent the Discovery's MPSC DMA interrupt hardware registers + (SDMA cause and mask registers). + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery MPSCINTR node: + mpsintr@b800 { + reg = <0xb800 0x100>; + }; + + + i) Marvell Discovery MPSC nodes + + Represent the Discovery's MPSC (Multiprotocol Serial Controller) + serial port. + + Required properties: + - device_type : "serial" + - compatible : "marvell,mv64360-mpsc" + - reg : Offset and length of the register set for this device + - sdma : the phandle for the SDMA node used by this port + - brg : the phandle for the BRG node used by this port + - cunit : the phandle for the CUNIT node used by this port + - mpscrouting : the phandle for the MPSCROUTING node used by this port + - mpscintr : the phandle for the MPSCINTR node used by this port + - cell-index : the hardware index of this cell in the MPSC core + - max_idle : value needed for MPSC CHR3 (Maximum Frame Length) + register + - interrupts : <a> where a is the interrupt number for the MPSC. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery MPSCINTR node: + mpsc@8000 { + device_type = "serial"; + compatible = "marvell,mv64360-mpsc"; + reg = <0x8000 0x38>; + virtual-reg = <0xf1008000>; + sdma = <&SDMA0>; + brg = <&BRG0>; + cunit = <&CUNIT>; + mpscrouting = <&MPSCROUTING>; + mpscintr = <&MPSCINTR>; + cell-index = <0>; + max_idle = <40>; + interrupts = <40>; + interrupt-parent = <&PIC>; + }; + + + j) Marvell Discovery Watch Dog Timer nodes + + Represent the Discovery's watchdog timer hardware + + Required properties: + - compatible : "marvell,mv64360-wdt" + - reg : Offset and length of the register set for this device + + Example Discovery Watch Dog Timer node: + wdt@b410 { + compatible = "marvell,mv64360-wdt"; + reg = <0xb410 0x8>; + }; + + + k) Marvell Discovery I2C nodes + + Represent the Discovery's I2C hardware + + Required properties: + - device_type : "i2c" + - compatible : "marvell,mv64360-i2c" + - reg : Offset and length of the register set for this device + - interrupts : <a> where a is the interrupt number for the I2C. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery I2C node: + compatible = "marvell,mv64360-i2c"; + reg = <0xc000 0x20>; + virtual-reg = <0xf100c000>; + interrupts = <37>; + interrupt-parent = <&PIC>; + }; + + + l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes + + Represent the Discovery's PIC hardware + + Required properties: + - #interrupt-cells : <1> + - #address-cells : <0> + - compatible : "marvell,mv64360-pic" + - reg : Offset and length of the register set for this device + - interrupt-controller + + Example Discovery PIC node: + pic { + #interrupt-cells = <1>; + #address-cells = <0>; + compatible = "marvell,mv64360-pic"; + reg = <0x0 0x88>; + interrupt-controller; + }; + + + m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes + + Represent the Discovery's MPP hardware + + Required properties: + - compatible : "marvell,mv64360-mpp" + - reg : Offset and length of the register set for this device + + Example Discovery MPP node: + mpp@f000 { + compatible = "marvell,mv64360-mpp"; + reg = <0xf000 0x10>; + }; + + + n) Marvell Discovery GPP (General Purpose Pins) nodes + + Represent the Discovery's GPP hardware + + Required properties: + - compatible : "marvell,mv64360-gpp" + - reg : Offset and length of the register set for this device + + Example Discovery GPP node: + gpp@f000 { + compatible = "marvell,mv64360-gpp"; + reg = <0xf100 0x20>; + }; + + + o) Marvell Discovery PCI host bridge node + + Represents the Discovery's PCI host bridge device. The properties + for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE + 1275-1994. A typical value for the compatible property is + "marvell,mv64360-pci". + + Example Discovery PCI host bridge node + pci@80000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + compatible = "marvell,mv64360-pci"; + reg = <0xcf8 0x8>; + ranges = <0x01000000 0x0 0x0 + 0x88000000 0x0 0x01000000 + 0x02000000 0x0 0x80000000 + 0x80000000 0x0 0x08000000>; + bus-range = <0 255>; + clock-frequency = <66000000>; + interrupt-parent = <&PIC>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0a */ + 0x5000 0 0 1 &PIC 80 + 0x5000 0 0 2 &PIC 81 + 0x5000 0 0 3 &PIC 91 + 0x5000 0 0 4 &PIC 93 + + /* IDSEL 0x0b */ + 0x5800 0 0 1 &PIC 91 + 0x5800 0 0 2 &PIC 93 + 0x5800 0 0 3 &PIC 80 + 0x5800 0 0 4 &PIC 81 + + /* IDSEL 0x0c */ + 0x6000 0 0 1 &PIC 91 + 0x6000 0 0 2 &PIC 93 + 0x6000 0 0 3 &PIC 80 + 0x6000 0 0 4 &PIC 81 + + /* IDSEL 0x0d */ + 0x6800 0 0 1 &PIC 93 + 0x6800 0 0 2 &PIC 80 + 0x6800 0 0 3 &PIC 81 + 0x6800 0 0 4 &PIC 91 + >; + }; + + + p) Marvell Discovery CPU Error nodes + + Represent the Discovery's CPU error handler device. + + Required properties: + - compatible : "marvell,mv64360-cpu-error" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery CPU Error node: + cpu-error@0070 { + compatible = "marvell,mv64360-cpu-error"; + reg = <0x70 0x10 0x128 0x28>; + interrupts = <3>; + interrupt-parent = <&PIC>; + }; + + + q) Marvell Discovery SRAM Controller nodes + + Represent the Discovery's SRAM controller device. + + Required properties: + - compatible : "marvell,mv64360-sram-ctrl" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery SRAM Controller node: + sram-ctrl@0380 { + compatible = "marvell,mv64360-sram-ctrl"; + reg = <0x380 0x80>; + interrupts = <13>; + interrupt-parent = <&PIC>; + }; + + + r) Marvell Discovery PCI Error Handler nodes + + Represent the Discovery's PCI error handler device. + + Required properties: + - compatible : "marvell,mv64360-pci-error" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery PCI Error Handler node: + pci-error@1d40 { + compatible = "marvell,mv64360-pci-error"; + reg = <0x1d40 0x40 0xc28 0x4>; + interrupts = <12>; + interrupt-parent = <&PIC>; + }; + + + s) Marvell Discovery Memory Controller nodes + + Represent the Discovery's memory controller device. + + Required properties: + - compatible : "marvell,mv64360-mem-ctrl" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery Memory Controller node: + mem-ctrl@1400 { + compatible = "marvell,mv64360-mem-ctrl"; + reg = <0x1400 0x60>; + interrupts = <17>; + interrupt-parent = <&PIC>; + }; + + diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt new file mode 100644 index 00000000000..64bcb8be973 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -0,0 +1,29 @@ +* Freescale Enhanced Secure Digital Host Controller (eSDHC) + +The Enhanced Secure Digital Host Controller provides an interface +for MMC, SD, and SDIO types of memory cards. + +Required properties: + - compatible : should be + "fsl,<chip>-esdhc", "fsl,esdhc" + - reg : should contain eSDHC registers location and length. + - interrupts : should contain eSDHC interrupt. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies eSDHC base clock frequency. + - sdhci,wp-inverted : (optional) specifies that eSDHC controller + reports inverted write-protect state; + - sdhci,1-bit-only : (optional) specifies that a controller can + only handle 1-bit data transfers. + - sdhci,auto-cmd12: (optional) specifies that a controller can + only handle auto CMD12. + +Example: + +sdhci@2e000 { + compatible = "fsl,mpc8378-esdhc", "fsl,esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <42 0x8>; + interrupt-parent = <&ipic>; + /* Filled in by U-Boot */ + clock-frequency = <0>; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt new file mode 100644 index 00000000000..c39ac289195 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt @@ -0,0 +1,23 @@ +MMC/SD/SDIO slot directly connected to a SPI bus + +Required properties: +- compatible : should be "mmc-spi-slot". +- reg : should specify SPI address (chip-select number). +- spi-max-frequency : maximum frequency for this device (Hz). +- voltage-ranges : two cells are required, first cell specifies minimum + slot voltage (mV), second cell specifies maximum slot voltage (mV). + Several ranges could be specified. +- gpios : (optional) may specify GPIOs in this order: Card-Detect GPIO, + Write-Protect GPIO. + +Example: + + mmc-slot@0 { + compatible = "fsl,mpc8323rdb-mmc-slot", + "mmc-spi-slot"; + reg = <0>; + gpios = <&qe_pio_d 14 1 + &qe_pio_d 15 0>; + voltage-ranges = <3300 3300>; + spi-max-frequency = <50000000>; + }; diff --git a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt new file mode 100644 index 00000000000..a48b2cadc7f --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt @@ -0,0 +1,63 @@ +Freescale Localbus UPM programmed to work with NAND flash + +Required properties: +- compatible : "fsl,upm-nand". +- reg : should specify localbus chip select and size used for the chip. +- fsl,upm-addr-offset : UPM pattern offset for the address latch. +- fsl,upm-cmd-offset : UPM pattern offset for the command latch. + +Optional properties: +- fsl,upm-wait-flags : add chip-dependent short delays after running the + UPM pattern (0x1), after writing a data byte (0x2) or after + writing out a buffer (0x4). +- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support. + The corresponding address lines are used to select the chip. +- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins + (R/B#). For multi-chip devices, "n" GPIO definitions are required + according to the number of chips. +- chip-delay : chip dependent delay for transfering data from array to + read registers (tR). Required if property "gpios" is not used + (R/B# pins not connected). + +Examples: + +upm@1,0 { + compatible = "fsl,upm-nand"; + reg = <1 0 1>; + fsl,upm-addr-offset = <16>; + fsl,upm-cmd-offset = <8>; + gpios = <&qe_pio_e 18 0>; + + flash { + #address-cells = <1>; + #size-cells = <1>; + compatible = "..."; + + partition@0 { + ... + }; + }; +}; + +upm@3,0 { + #address-cells = <0>; + #size-cells = <0>; + compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand"; + reg = <3 0x0 0x800>; + fsl,upm-addr-offset = <0x10>; + fsl,upm-cmd-offset = <0x08>; + /* Multi-chip NAND device */ + fsl,upm-addr-line-cs-offsets = <0x0 0x200>; + fsl,upm-wait-flags = <0x5>; + chip-delay = <25>; // in micro-seconds + + nand@0 { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fs"; + reg = <0x00000000 0x10000000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt new file mode 100644 index 00000000000..80152cb567d --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -0,0 +1,90 @@ +CFI or JEDEC memory-mapped NOR flash, MTD-RAM (NVRAM...) + +Flash chips (Memory Technology Devices) are often used for solid state +file systems on embedded devices. + + - compatible : should contain the specific model of mtd chip(s) + used, if known, followed by either "cfi-flash", "jedec-flash" + or "mtd-ram". + - reg : Address range(s) of the mtd chip(s) + It's possible to (optionally) define multiple "reg" tuples so that + non-identical chips can be described in one node. + - bank-width : Width (in bytes) of the bank. Equal to the + device width times the number of interleaved chips. + - device-width : (optional) Width of a single mtd chip. If + omitted, assumed to be equal to 'bank-width'. + - #address-cells, #size-cells : Must be present if the device has + sub-nodes representing partitions (see below). In this case + both #address-cells and #size-cells must be equal to 1. + +For JEDEC compatible devices, the following additional properties +are defined: + + - vendor-id : Contains the flash chip's vendor id (1 byte). + - device-id : Contains the flash chip's device id (1 byte). + +In addition to the information on the mtd bank itself, the +device tree may optionally contain additional information +describing partitions of the address space. This can be +used on platforms which have strong conventions about which +portions of a flash are used for what purposes, but which don't +use an on-flash partition table such as RedBoot. + +Each partition is represented as a sub-node of the mtd device. +Each node's name represents the name of the corresponding +partition of the mtd device. + +Flash partitions + - reg : The partition's offset and size within the mtd bank. + - label : (optional) The label / name for this partition. + If omitted, the label is taken from the node name (excluding + the unit address). + - read-only : (optional) This parameter, if present, is a hint to + Linux that this partition should only be mounted + read-only. This is usually used for flash partitions + containing early-boot firmware images or data which should not + be clobbered. + +Example: + + flash@ff000000 { + compatible = "amd,am29lv128ml", "cfi-flash"; + reg = <ff000000 01000000>; + bank-width = <4>; + device-width = <1>; + #address-cells = <1>; + #size-cells = <1>; + fs@0 { + label = "fs"; + reg = <0 f80000>; + }; + firmware@f80000 { + label ="firmware"; + reg = <f80000 80000>; + read-only; + }; + }; + +Here an example with multiple "reg" tuples: + + flash@f0000000,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "intel,PC48F4400P0VB", "cfi-flash"; + reg = <0 0x00000000 0x02000000 + 0 0x02000000 0x02000000>; + bank-width = <2>; + partition@0 { + label = "test-part1"; + reg = <0 0x04000000>; + }; + }; + +An example using SRAM: + + sram@2,0 { + compatible = "samsung,k6f1616u6a", "mtd-ram"; + reg = <2 0 0x00200000>; + bank-width = <2>; + }; + diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt new file mode 100644 index 00000000000..2fa4fcd38fd --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt @@ -0,0 +1,53 @@ +CAN Device Tree Bindings +------------------------ + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. + +fsl,mpc5121-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source and divider shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock + "sys" for system clock + If this property is not present, an optimal CAN + clock source and frequency based on the system + clock will be selected. If this is not possible, + the reference clock will be used. + +- fsl,mscan-clock-divider: for the reference and system clock, an additional + clock divider can be specified. By default, a + value of 1 is used. + +Note that the MPC5121 Rev. 1 processor is not supported. + +Examples: + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1380 0x80>; + fsl,mscan-clock-source = "ref"; + fsl,mscan-clock-divider = <3>; + }; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt new file mode 100644 index 00000000000..d6d209ded93 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -0,0 +1,53 @@ +Memory mapped SJA1000 CAN controller from NXP (formerly Philips) + +Required properties: + +- compatible : should be "nxp,sja1000". + +- reg : should specify the chip select, address offset and size required + to map the registers of the SJA1000. The size is usually 0x80. + +- interrupts: property with a value describing the interrupt source + (number and sensitivity) required for the SJA1000. + +Optional properties: + +- nxp,external-clock-frequency : Frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + SJA1000 is half of that value. If not specified, a default value + of 16000000 (16 MHz) is used. + +- nxp,tx-output-mode : operation mode of the TX output control logic: + <0x0> : bi-phase output mode + <0x1> : normal output mode (default) + <0x2> : test output mode + <0x3> : clock output mode + +- nxp,tx-output-config : TX output pin configuration: + <0x01> : TX0 invert + <0x02> : TX0 pull-down (default) + <0x04> : TX0 pull-up + <0x06> : TX0 push-pull + <0x08> : TX1 invert + <0x10> : TX1 pull-down + <0x20> : TX1 pull-up + <0x30> : TX1 push-pull + +- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- nxp,no-comparator-bypass : Allows to disable the CAN input comperator. + +For futher information, please have a look to the SJA1000 data sheet. + +Examples: + +can@3,100 { + compatible = "nxp,sja1000"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + nxp,external-clock-frequency = <16000000>; +}; + diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt new file mode 100644 index 00000000000..edb7ae19e86 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -0,0 +1,76 @@ +* MDIO IO device + +The MDIO is a bus to which the PHY devices are connected. For each +device that exists on this bus, a child node should be created. See +the definition of the PHY node in booting-without-of.txt for an example +of how to define a PHY. + +Required properties: + - reg : Offset and length of the register set for the device + - compatible : Should define the compatible device type for the + mdio. Currently, this is most likely to be "fsl,gianfar-mdio" + +Example: + + mdio@24520 { + reg = <24520 20>; + compatible = "fsl,gianfar-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + +* TBI Internal MDIO bus + +As of this writing, every tsec is associated with an internal TBI PHY. +This PHY is accessed through the local MDIO bus. These buses are defined +similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". +The TBI PHYs underneath them are similar to normal PHYs, but the reg property +is considered instructive, rather than descriptive. The reg property should +be chosen so it doesn't interfere with other PHYs on the bus. + +* Gianfar-compatible ethernet nodes + +Properties: + + - device_type : Should be "network" + - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" + - compatible : Should be "gianfar" + - reg : Offset and length of the register set for the device + - local-mac-address : List of bytes representing the ethernet address of + this controller + - interrupts : For FEC devices, the first interrupt is the device's + interrupt. For TSEC and eTSEC devices, the first interrupt is + transmit, the second is receive, and the third is error. + - phy-handle : The phandle for the PHY connected to this ethernet + controller. + - fixed-link : <a b c d e> where a is emulated phy id - choose any, + but unique to the all specified fixed-links, b is duplex - 0 half, + 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no + pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. + - phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii", + "tbi", or "rtbi". This property is only really needed if the connection + is of type "rgmii-id", as all other connection types are detected by + hardware. + - fsl,magic-packet : If present, indicates that the hardware supports + waking up via magic packet. + - bd-stash : If present, indicates that the hardware supports stashing + buffer descriptors in the L2. + - rx-stash-len : Denotes the number of bytes of a received buffer to stash + in the L2. + - rx-stash-idx : Denotes the index of the first byte from the received + buffer to stash in the L2. + +Example: + ethernet@24000 { + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 E0 0C 00 73 00 ]; + interrupts = <29 2 30 2 34 2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy0> + }; diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt new file mode 100644 index 00000000000..bc954952901 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -0,0 +1,19 @@ +MDIO on GPIOs + +Currently defined compatibles: +- virtual,gpio-mdio + +MDC and MDIO lines connected to GPIO controllers are listed in the +gpios property as described in section VIII.1 in the following order: + +MDC, MDIO. + +Example: + +mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qe_pio_a 11 + &qe_pio_c 6>; +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt new file mode 100644 index 00000000000..bb8c742eb8c --- /dev/null +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -0,0 +1,25 @@ +PHY nodes + +Required properties: + + - device_type : Should be "ethernet-phy" + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + - linux,phandle : phandle for this node; likely referenced by an + ethernet controller node. + +Example: + +ethernet-phy@0 { + linux,phandle = <2452000> + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <0>; + device_type = "ethernet-phy"; +}; diff --git a/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt new file mode 100644 index 00000000000..35a46536240 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt @@ -0,0 +1,40 @@ +* Freescale 83xx and 512x PCI bridges + +Freescale 83xx and 512x SOCs include the same pci bridge core. + +83xx/512x specific notes: +- reg: should contain two address length tuples + The first is for the internal pci bridge registers + The second is for the pci config space access registers + +Example (MPC8313ERDB) + pci0: pci@e0008500 { + cell-index = <1>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0E -mini PCI */ + 0x7000 0x0 0x0 0x1 &ipic 18 0x8 + 0x7000 0x0 0x0 0x2 &ipic 18 0x8 + 0x7000 0x0 0x0 0x3 &ipic 18 0x8 + 0x7000 0x0 0x0 0x4 &ipic 18 0x8 + + /* IDSEL 0x0F - PCI slot */ + 0x7800 0x0 0x0 0x1 &ipic 17 0x8 + 0x7800 0x0 0x0 0x2 &ipic 18 0x8 + 0x7800 0x0 0x0 0x3 &ipic 17 0x8 + 0x7800 0x0 0x0 0x4 &ipic 18 0x8>; + interrupt-parent = <&ipic>; + interrupts = <66 0x8>; + bus-range = <0x0 0x0>; + ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 + 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 + 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + clock-frequency = <66666666>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ + compatible = "fsl,mpc8349-pci"; + device_type = "pci"; + }; diff --git a/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt b/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt new file mode 100644 index 00000000000..ee459806d35 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/cpm.txt @@ -0,0 +1,52 @@ +PPC4xx Clock Power Management (CPM) node + +Required properties: + - compatible : compatible list, currently only "ibm,cpm" + - dcr-access-method : "native" + - dcr-reg : < DCR register range > + +Optional properties: + - er-offset : All 4xx SoCs with a CPM controller have + one of two different order for the CPM + registers. Some have the CPM registers + in the following order (ER,FR,SR). The + others have them in the following order + (SR,ER,FR). For the second case set + er-offset = <1>. + - unused-units : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set to turn off unused + devices. + - idle-doze : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set to turn off unused + devices. This is usually just CPM[CPU]. + - standby : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set on standby and + restored on resume. + - suspend : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set on suspend (mem) and + restored on resume. Note, for standby + and suspend the corresponding bits can + be different or the same. Usually for + standby only class 2 and 3 units are set. + However, the interface does not care. + If they are the same, the additional + power saving will be seeing if support + is available to put the DDR in self + refresh mode and any additional power + saving techniques for the specific SoC. + +Example: + CPM0: cpm { + compatible = "ibm,cpm"; + dcr-access-method = "native"; + dcr-reg = <0x160 0x003>; + er-offset = <0>; + unused-units = <0x00000100>; + idle-doze = <0x02000000>; + standby = <0xfeff0000>; + suspend = <0xfeff791d>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt new file mode 100644 index 00000000000..2161334a7ca --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt @@ -0,0 +1,148 @@ + 4xx/Axon EMAC ethernet nodes + + The EMAC ethernet controller in IBM and AMCC 4xx chips, and also + the Axon bridge. To operate this needs to interact with a ths + special McMAL DMA controller, and sometimes an RGMII or ZMII + interface. In addition to the nodes and properties described + below, the node for the OPB bus on which the EMAC sits must have a + correct clock-frequency property. + + i) The EMAC node itself + + Required properties: + - device_type : "network" + + - compatible : compatible list, contains 2 entries, first is + "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, + 405gp, Axon) and second is either "ibm,emac" or + "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", + "ibm,emac4" + - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + - reg : <registers mapping> + - local-mac-address : 6 bytes, MAC address + - mal-device : phandle of the associated McMAL node + - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated + with this EMAC + - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated + with this EMAC + - cell-index : 1 cell, hardware index of the EMAC cell on a given + ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on + each Axon chip) + - max-frame-size : 1 cell, maximum frame size supported in bytes + - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048 + - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048. + - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate + thresholds). + For Axon, 0x00000010 + - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) + in bytes. + For Axon, 0x00000100 (I think ...) + - phy-mode : string, mode of operations of the PHY interface. + Supported values are: "mii", "rmii", "smii", "rgmii", + "tbi", "gmii", rtbi", "sgmii". + For Axon on CAB, it is "rgmii" + - mdio-device : 1 cell, required iff using shared MDIO registers + (440EP). phandle of the EMAC to use to drive the + MDIO lines for the PHY used by this EMAC. + - zmii-device : 1 cell, required iff connected to a ZMII. phandle of + the ZMII device node + - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII + channel or 0xffffffff if ZMII is only used for MDIO. + - rgmii-device : 1 cell, required iff connected to an RGMII. phandle + of the RGMII device node. + For Axon: phandle of plb5/plb4/opb/rgmii + - rgmii-channel : 1 cell, required iff connected to an RGMII. Which + RGMII channel is used by this EMAC. + Fox Axon: present, whatever value is appropriate for each + EMAC, that is the content of the current (bogus) "phy-port" + property. + + Optional properties: + - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, + a search is performed. + - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY + for, used if phy-address is absent. bit 0x00000001 is + MDIO address 0. + For Axon it can be absent, though my current driver + doesn't handle phy-address yet so for now, keep + 0x00ffffff in it. + - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + rx-fifo-size). For Axon, either absent or 2048. + - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + tx-fifo-size). For Axon, either absent or 2048. + - tah-device : 1 cell, optional. If connected to a TAH engine for + offload, phandle of the TAH device node. + - tah-channel : 1 cell, optional. If appropriate, channel used on the + TAH engine. + + Example: + + EMAC0: ethernet@40000800 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1c 4 1d 4>; + reg = <40000800 70>; + local-mac-address = [00 04 AC E3 1B 1E]; + mal-device = <&MAL0>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <0>; + }; + + ii) McMAL node + + Required properties: + - device_type : "dma-controller" + - compatible : compatible list, containing 2 entries, first is + "ibm,mcmal-CHIP" where CHIP is the host ASIC (like + emac) and the second is either "ibm,mcmal" or + "ibm,mcmal2". + For Axon, "ibm,mcmal-axon","ibm,mcmal2" + - interrupts : <interrupt mapping for the MAL interrupts sources: + 5 sources: tx_eob, rx_eob, serr, txde, rxde>. + For Axon: This is _different_ from the current + firmware. We use the "delayed" interrupts for txeob + and rxeob. Thus we end up with mapping those 5 MPIC + interrupts, all level positive sensitive: 10, 11, 32, + 33, 34 (in decimal) + - dcr-reg : < DCR registers range > + - dcr-parent : if needed for dcr-reg + - num-tx-chans : 1 cell, number of Tx channels + - num-rx-chans : 1 cell, number of Rx channels + + iii) ZMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,zmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,zmii". + For Axon, there is no ZMII node. + - reg : <registers mapping> + + iv) RGMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,rgmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,rgmii". + For Axon, "ibm,rgmii-axon","ibm,rgmii" + - reg : <registers mapping> + - revision : as provided by the RGMII new version register if + available. + For Axon: 0x0000012a + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt b/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt new file mode 100644 index 00000000000..869f0b5f16e --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/ndfc.txt @@ -0,0 +1,39 @@ +AMCC NDFC (NanD Flash Controller) + +Required properties: +- compatible : "ibm,ndfc". +- reg : should specify chip select and size used for the chip (0x2000). + +Optional properties: +- ccr : NDFC config and control register value (default 0). +- bank-settings : NDFC bank configuration register value (default 0). + +Notes: +- partition(s) - follows the OF MTD standard for partitions + +Example: + +ndfc@1,0 { + compatible = "ibm,ndfc"; + reg = <0x00000001 0x00000000 0x00002000>; + ccr = <0x00001000>; + bank-settings = <0x80002222>; + #address-cells = <1>; + #size-cells = <1>; + + nand { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x00000000 0x00200000>; + }; + partition@200000 { + label = "root"; + reg = <0x00200000 0x03E00000>; + }; + }; +}; + + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt b/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt new file mode 100644 index 00000000000..515ebcf1b97 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/ppc440spe-adma.txt @@ -0,0 +1,93 @@ +PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator) + +Device nodes needed for operation of the ppc440spe-adma driver +are specified hereby. These are I2O/DMA, DMA and XOR nodes +for DMA engines and Memory Queue Module node. The latter is used +by ADMA driver for configuration of RAID-6 H/W capabilities of +the PPC440SPe. In addition to the nodes and properties described +below, the ranges property of PLB node must specify ranges for +DMA devices. + + i) The I2O node + + Required properties: + + - compatible : "ibm,i2o-440spe"; + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + + Example: + + I2O: i2o@400100000 { + compatible = "ibm,i2o-440spe"; + reg = <0x00000004 0x00100000 0x100>; + dcr-reg = <0x060 0x020>; + }; + + + ii) The DMA node + + Required properties: + + - compatible : "ibm,dma-440spe"; + - cell-index : 1 cell, hardware index of the DMA engine + (typically 0x0 and 0x1 for DMA0 and DMA1) + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + - interrupts : <interrupt mapping for DMA0/1 interrupts sources: + 2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0) + and DMA Error IRQ (on UIC1). The latter is common + for both DMA engines>. + - interrupt-parent : needed for interrupt mapping + + Example: + + DMA0: dma0@400100100 { + compatible = "ibm,dma-440spe"; + cell-index = <0>; + reg = <0x00000004 0x00100100 0x100>; + dcr-reg = <0x060 0x020>; + interrupt-parent = <&DMA0>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = < + 0 &UIC0 0x14 4 + 1 &UIC1 0x16 4>; + }; + + + iii) XOR Accelerator node + + Required properties: + + - compatible : "amcc,xor-accelerator"; + - reg : <registers mapping> + - interrupts : <interrupt mapping for XOR interrupt source> + - interrupt-parent : for interrupt mapping + + Example: + + xor-accel@400200000 { + compatible = "amcc,xor-accelerator"; + reg = <0x00000004 0x00200000 0x400>; + interrupt-parent = <&UIC1>; + interrupts = <0x1f 4>; + }; + + + iv) Memory Queue Module node + + Required properties: + + - compatible : "ibm,mq-440spe"; + - dcr-reg : <DCR registers range> + + Example: + + MQ0: mq { + compatible = "ibm,mq-440spe"; + dcr-reg = <0x040 0x020>; + }; + diff --git a/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt new file mode 100644 index 00000000000..d7217260589 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt @@ -0,0 +1,18 @@ +Reboot property to control system reboot on PPC4xx systems: + +By setting "reset_type" to one of the following values, the default +software reset mechanism may be overidden. Here the possible values of +"reset_type": + + 1 - PPC4xx core reset + 2 - PPC4xx chip reset + 3 - PPC4xx system reset (default) + +Example: + + cpu@0 { + device_type = "cpu"; + model = "PowerPC,440SPe"; + ... + reset-type = <2>; /* Use chip-reset */ + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/powerpc/fsl/board.txt new file mode 100644 index 00000000000..39e941515a3 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/board.txt @@ -0,0 +1,63 @@ +* Board Control and Status (BCSR) + +Required properties: + + - compatible : Should be "fsl,<board>-bcsr" + - reg : Offset and length of the register set for the device + +Example: + + bcsr@f8000000 { + compatible = "fsl,mpc8360mds-bcsr"; + reg = <f8000000 8000>; + }; + +* Freescale on board FPGA + +This is the memory-mapped registers for on board FPGA. + +Required properities: +- compatible : should be "fsl,fpga-pixis". +- reg : should contain the address and the length of the FPPGA register + set. +- interrupt-parent: should specify phandle for the interrupt controller. +- interrupts : should specify event (wakeup) IRQ. + +Example (MPC8610HPCD): + + board-control@e8000000 { + compatible = "fsl,fpga-pixis"; + reg = <0xe8000000 32>; + interrupt-parent = <&mpic>; + interrupts = <8 8>; + }; + +* Freescale BCSR GPIO banks + +Some BCSR registers act as simple GPIO controllers, each such +register can be represented by the gpio-controller node. + +Required properities: +- compatible : Should be "fsl,<board>-bcsr-gpio". +- reg : Should contain the address and the length of the GPIO bank + register. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the port as GPIO controller. + +Example: + + bcsr@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8360mds-bcsr"; + reg = <1 0 0x8000>; + ranges = <0 1 0 0x8000>; + + bcsr13: gpio-controller@d { + #gpio-cells = <2>; + compatible = "fsl,mpc8360mds-bcsr-gpio"; + reg = <0xd 1>; + gpio-controller; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt new file mode 100644 index 00000000000..160c752484b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt @@ -0,0 +1,67 @@ +* Freescale Communications Processor Module + +NOTE: This is an interim binding, and will likely change slightly, +as more devices are supported. The QE bindings especially are +incomplete. + +* Root CPM node + +Properties: +- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". +- reg : A 48-byte region beginning with CPCR. + +Example: + cpm@119c0 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; + reg = <119c0 30>; + } + +* Properties common to multiple CPM/QE devices + +- fsl,cpm-command : This value is ORed with the opcode and command flag + to specify the device on which a CPM command operates. + +- fsl,cpm-brg : Indicates which baud rate generator the device + is associated with. If absent, an unused BRG + should be dynamically allocated. If zero, the + device uses an external clock rather than a BRG. + +- reg : Unless otherwise specified, the first resource represents the + scc/fcc/ucc registers, and the second represents the device's + parameter RAM region (if it has one). + +* Multi-User RAM (MURAM) + +The multi-user/dual-ported RAM is expressed as a bus under the CPM node. + +Ranges must be set up subject to the following restrictions: + +- Children's reg nodes must be offsets from the start of all muram, even + if the user-data area does not begin at zero. +- If multiple range entries are used, the difference between the parent + address and the child address must be the same in all, so that a single + mapping can cover them all while maintaining the ability to determine + CPM-side offsets with pointer subtraction. It is recommended that + multiple range entries not be used. +- A child address of zero must be translatable, even if no reg resources + contain it. + +A child "data" node must exist, compatible with "fsl,cpm-muram-data", to +indicate the portion of muram that is usable by the OS for arbitrary +purposes. The data node may have an arbitrary number of reg resources, +all of which contribute to the allocatable muram pool. + +Example, based on mpc8272: + muram@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 10000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0 2000 9800 800>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt new file mode 100644 index 00000000000..4c7d45eaf02 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt @@ -0,0 +1,21 @@ +* Baud Rate Generators + +Currently defined compatibles: +fsl,cpm-brg +fsl,cpm1-brg +fsl,cpm2-brg + +Properties: +- reg : There may be an arbitrary number of reg resources; BRG + numbers are assigned to these in order. +- clock-frequency : Specifies the base frequency driving + the BRG. + +Example: + brg@119f0 { + compatible = "fsl,mpc8272-brg", + "fsl,cpm2-brg", + "fsl,cpm-brg"; + reg = <119f0 10 115f0 10>; + clock-frequency = <d#25000000>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt new file mode 100644 index 00000000000..87bc6048667 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt @@ -0,0 +1,41 @@ +* I2C + +The I2C controller is expressed as a bus under the CPM node. + +Properties: +- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" +- reg : On CPM2 devices, the second resource doesn't specify the I2C + Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM + (typically 0x8afc 0x2). +- #address-cells : Should be one. The cell is the i2c device address with + the r/w bit set to zero. +- #size-cells : Should be zero. +- clock-frequency : Can be used to set the i2c clock frequency. If + unspecified, a default frequency of 60kHz is being used. +The following two properties are deprecated. They are only used by legacy +i2c drivers to find the bus to probe: +- linux,i2c-index : Can be used to hard code an i2c bus number. By default, + the bus number is dynamically assigned by the i2c core. +- linux,i2c-class : Can be used to override the i2c class. The class is used + by legacy i2c device drivers to find a bus in a specific context like + system management, video or sound. By default, I2C_CLASS_HWMON (1) is + being used. The definition of the classes can be found in + include/i2c/i2c.h + +Example, based on mpc823: + + i2c@860 { + compatible = "fsl,mpc823-i2c", + "fsl,cpm1-i2c"; + reg = <0x860 0x20 0x3c80 0x30>; + interrupts = <16>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-command = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt new file mode 100644 index 00000000000..8e3ee168161 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt @@ -0,0 +1,18 @@ +* Interrupt Controllers + +Currently defined compatibles: +- fsl,cpm1-pic + - only one interrupt cell +- fsl,pq1-pic +- fsl,cpm2-pic + - second interrupt cell is level/sense: + - 2 is falling edge + - 8 is active low + +Example: + interrupt-controller@10c00 { + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + compatible = "mpc8272-pic", "fsl,cpm2-pic"; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt new file mode 100644 index 00000000000..74bfda4bb82 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt @@ -0,0 +1,15 @@ +* USB (Universal Serial Bus Controller) + +Properties: +- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" + +Example: + usb@11bc0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,cpm2-usb"; + reg = <11b60 18 8b00 100>; + interrupts = <b 8>; + interrupt-parent = <&PIC>; + fsl,cpm-command = <2e600000>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt new file mode 100644 index 00000000000..349f79fd707 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt @@ -0,0 +1,38 @@ +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +On CPM1 devices, all ports are using slightly different register layouts. +Ports A, C and D are 16bit ports and Ports B and E are 32bit ports. + +On CPM2 devices, all ports are 32bit ports and use a common register layout. + +Required properties: +- compatible : "fsl,cpm1-pario-bank-a", "fsl,cpm1-pario-bank-b", + "fsl,cpm1-pario-bank-c", "fsl,cpm1-pario-bank-d", + "fsl,cpm1-pario-bank-e", "fsl,cpm2-pario-bank" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the port as GPIO controller. + +Example of three SOC GPIO banks defined as gpio-controller nodes: + + CPM1_PIO_A: gpio-controller@950 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-a"; + reg = <0x950 0x10>; + gpio-controller; + }; + + CPM1_PIO_B: gpio-controller@ab8 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-b"; + reg = <0xab8 0x10>; + gpio-controller; + }; + + CPM1_PIO_E: gpio-controller@ac8 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-e"; + reg = <0xac8 0x18>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt new file mode 100644 index 00000000000..0e426944658 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt @@ -0,0 +1,45 @@ +* Network + +Currently defined compatibles: +- fsl,cpm1-scc-enet +- fsl,cpm2-scc-enet +- fsl,cpm1-fec-enet +- fsl,cpm2-fcc-enet (third resource is GFEMR) +- fsl,qe-enet + +Example: + + ethernet@11300 { + device_type = "network"; + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <11300 20 8400 100 11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY0>; + fsl,cpm-command = <12000300>; + }; + +* MDIO + +Currently defined compatibles: +fsl,pq1-fec-mdio (reg is same as first resource of FEC device) +fsl,cpm2-mdio-bitbang (reg is port C registers) + +Properties for fsl,cpm2-mdio-bitbang: +fsl,mdio-pin : pin of port C controlling mdio data +fsl,mdc-pin : pin of port C controlling mdio clock + +Example: + mdio@10d40 { + device_type = "mdio"; + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <10d40 14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt new file mode 100644 index 00000000000..4f8930263dd --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt @@ -0,0 +1,115 @@ +* Freescale QUICC Engine module (QE) +This represents qe module that is installed on PowerQUICC II Pro. + +NOTE: This is an interim binding; it should be updated to fit +in with the CPM binding later in this document. + +Basically, it is a bus of devices, that could act more or less +as a complete entity (UCC, USB etc ). All of them should be siblings on +the "root" qe node, using the common properties from there. +The description below applies to the qe of MPC8360 and +more nodes and properties would be extended in the future. + +i) Root QE device + +Required properties: +- compatible : should be "fsl,qe"; +- model : precise model of the QE, Can be "QE", "CPM", or "CPM2" +- reg : offset and length of the device registers. +- bus-frequency : the clock frequency for QUICC Engine. +- fsl,qe-num-riscs: define how many RISC engines the QE has. +- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the + threads. + +Optional properties: +- fsl,firmware-phandle: + Usage: required only if there is no fsl,qe-firmware child node + Value type: <phandle> + Definition: Points to a firmware node (see "QE Firmware Node" below) + that contains the firmware that should be uploaded for this QE. + The compatible property for the firmware node should say, + "fsl,qe-firmware". + +Recommended properties +- brg-frequency : the internal clock source frequency for baud-rate + generators in Hz. + +Example: + qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,qe"; + ranges = <0 e0100000 00100000>; + reg = <e0100000 480>; + brg-frequency = <0>; + bus-frequency = <179A7B00>; + } + +* Multi-User RAM (MURAM) + +Required properties: +- compatible : should be "fsl,qe-muram", "fsl,cpm-muram". +- mode : the could be "host" or "slave". +- ranges : Should be defined as specified in 1) to describe the + translation of MURAM addresses. +- data-only : sub-node which defines the address area under MURAM + bus that can be allocated as data/parameter + +Example: + + muram@10000 { + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0 c000>; + }; + }; + +* QE Firmware Node + +This node defines a firmware binary that is embedded in the device tree, for +the purpose of passing the firmware from bootloader to the kernel, or from +the hypervisor to the guest. + +The firmware node itself contains the firmware binary contents, a compatible +property, and any firmware-specific properties. The node should be placed +inside a QE node that needs it. Doing so eliminates the need for a +fsl,firmware-phandle property. Other QE nodes that need the same firmware +should define an fsl,firmware-phandle property that points to the firmware node +in the first QE node. + +The fsl,firmware property can be specified in the DTS (possibly using incbin) +or can be inserted by the boot loader at boot time. + +Required properties: + - compatible + Usage: required + Value type: <string> + Definition: A standard property. Specify a string that indicates what + kind of firmware it is. For QE, this should be "fsl,qe-firmware". + + - fsl,firmware + Usage: required + Value type: <prop-encoded-array>, encoded as an array of bytes + Definition: A standard property. This property contains the firmware + binary "blob". + +Example: + qe1@e0080000 { + compatible = "fsl,qe"; + qe_firmware:qe-firmware { + compatible = "fsl,qe-firmware"; + fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...]; + }; + ... + }; + + qe2@e0090000 { + compatible = "fsl,qe"; + fsl,firmware-phandle = <&qe_firmware>; + ... + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt new file mode 100644 index 00000000000..249db3a15d1 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt @@ -0,0 +1,24 @@ +* Uploaded QE firmware + + If a new firmware has been uploaded to the QE (usually by the + boot loader), then a 'firmware' child node should be added to the QE + node. This node provides information on the uploaded firmware that + device drivers may need. + + Required properties: + - id: The string name of the firmware. This is taken from the 'id' + member of the qe_firmware structure of the uploaded firmware. + Device drivers can search this string to determine if the + firmware they want is already present. + - extended-modes: The Extended Modes bitfield, taken from the + firmware binary. It is a 64-bit number represented + as an array of two 32-bit numbers. + - virtual-traps: The virtual traps, taken from the firmware binary. + It is an array of 8 32-bit numbers. + +Example: + firmware { + id = "Soft-UART"; + extended-modes = <0 0>; + virtual-traps = <0 0 0 0 0 0 0 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt new file mode 100644 index 00000000000..60984260207 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt @@ -0,0 +1,51 @@ +* Parallel I/O Ports + +This node configures Parallel I/O ports for CPUs with QE support. +The node should reside in the "soc" node of the tree. For each +device that using parallel I/O ports, a child node should be created. +See the definition of the Pin configuration nodes below for more +information. + +Required properties: +- device_type : should be "par_io". +- reg : offset to the register set and its length. +- num-ports : number of Parallel I/O ports + +Example: +par_io@1400 { + reg = <1400 100>; + #address-cells = <1>; + #size-cells = <0>; + device_type = "par_io"; + num-ports = <7>; + ucc_pin@01 { + ...... + }; + +Note that "par_io" nodes are obsolete, and should not be used for +the new device trees. Instead, each Par I/O bank should be represented +via its own gpio-controller node: + +Required properties: +- #gpio-cells : should be "2". +- compatible : should be "fsl,<chip>-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank". +- reg : offset to the register set and its length. +- gpio-controller : node to identify gpio controllers. + +Example: + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt new file mode 100644 index 00000000000..c5b43061db3 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt @@ -0,0 +1,60 @@ +* Pin configuration nodes + +Required properties: +- linux,phandle : phandle of this node; likely referenced by a QE + device. +- pio-map : array of pin configurations. Each pin is defined by 6 + integers. The six numbers are respectively: port, pin, dir, + open_drain, assignment, has_irq. + - port : port number of the pin; 0-6 represent port A-G in UM. + - pin : pin number in the port. + - dir : direction of the pin, should encode as follows: + + 0 = The pin is disabled + 1 = The pin is an output + 2 = The pin is an input + 3 = The pin is I/O + + - open_drain : indicates the pin is normal or wired-OR: + + 0 = The pin is actively driven as an output + 1 = The pin is an open-drain driver. As an output, the pin is + driven active-low, otherwise it is three-stated. + + - assignment : function number of the pin according to the Pin Assignment + tables in User Manual. Each pin can have up to 4 possible functions in + QE and two options for CPM. + - has_irq : indicates if the pin is used as source of external + interrupts. + +Example: + ucc_pin@01 { + linux,phandle = <140001>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 1 6 1 0 3 0 /* TxD4 */ + 1 7 1 0 1 0 /* TxD5 */ + 1 9 1 0 2 0 /* TxD6 */ + 1 a 1 0 2 0 /* TxD7 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 a 2 0 1 0 /* RxD1 */ + 0 b 2 0 1 0 /* RxD2 */ + 0 c 2 0 1 0 /* RxD3 */ + 0 d 2 0 1 0 /* RxD4 */ + 1 1 2 0 2 0 /* RxD5 */ + 1 0 2 0 2 0 /* RxD6 */ + 1 4 2 0 2 0 /* RxD7 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 f 2 0 1 0 /* RX_DV */ + 0 10 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0>; /* GTX125 - CLK9 */ + }; + + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt new file mode 100644 index 00000000000..e47734bee3f --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt @@ -0,0 +1,70 @@ +* UCC (Unified Communications Controllers) + +Required properties: +- device_type : should be "network", "hldc", "uart", "transparent" + "bisync", "atm", or "serial". +- compatible : could be "ucc_geth" or "fsl_atm" and so on. +- cell-index : the ucc number(1-8), corresponding to UCCx in UM. +- reg : Offset and length of the register set for the device +- interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. +- pio-handle : The phandle for the Parallel I/O port configuration. +- port-number : for UART drivers, the port number to use, between 0 and 3. + This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. + The port number is added to the minor number of the device. Unlike the + CPM UART driver, the port-number is required for the QE UART driver. +- soft-uart : for UART drivers, if specified this means the QE UART device + driver should use "Soft-UART" mode, which is needed on some SOCs that have + broken UART hardware. Soft-UART is provided via a microcode upload. +- rx-clock-name: the UCC receive clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- tx-clock-name: the UCC transmit clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +The following two properties are deprecated. rx-clock has been replaced +with rx-clock-name, and tx-clock has been replaced with tx-clock-name. +Drivers that currently use the deprecated properties should continue to +do so, in order to support older device trees, but they should be updated +to check for the new properties first. +- rx-clock : represents the UCC receive clock source. + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. +- tx-clock: represents the UCC transmit clock source; + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. + +Required properties for network device_type: +- mac-address : list of bytes representing the ethernet address. +- phy-handle : The phandle for the PHY connected to this controller. + +Recommended properties: +- phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal + Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), + "tbi", or "rtbi". + +Example: + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <2000 200>; + interrupts = <a0 0>; + interrupt-parent = <700>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = "none"; + tx-clock = "clk9"; + phy-handle = <212000>; + phy-connection-type = "gmii"; + pio-handle = <140001>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt new file mode 100644 index 00000000000..9ccd5f30405 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt @@ -0,0 +1,37 @@ +Freescale QUICC Engine USB Controller + +Required properties: +- compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb". +- reg : the first two cells should contain usb registers location and + length, the next two two cells should contain PRAM location and + length. +- interrupts : should contain USB interrupt. +- interrupt-parent : interrupt source phandle. +- fsl,fullspeed-clock : specifies the full speed USB clock source: + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- fsl,lowspeed-clock : specifies the low speed USB clock source: + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- hub-power-budget : USB power budget for the root hub, in mA. +- gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP, + USBRN, SPEED (optional), and POWER (optional). + +Example: + +usb@6c0 { + compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb"; + reg = <0x6c0 0x40 0x8b00 0x100>; + interrupts = <11>; + interrupt-parent = <&qeic>; + fsl,fullspeed-clock = "clk21"; + gpios = <&qe_pio_b 2 0 /* USBOE */ + &qe_pio_b 3 0 /* USBTP */ + &qe_pio_b 8 0 /* USBTN */ + &qe_pio_b 9 0 /* USBRP */ + &qe_pio_b 11 0 /* USBRN */ + &qe_pio_e 20 0 /* SPEED */ + &qe_pio_e 21 0 /* POWER */>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt new file mode 100644 index 00000000000..2ea76d9d137 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt @@ -0,0 +1,32 @@ +* Serial + +Currently defined compatibles: +- fsl,cpm1-smc-uart +- fsl,cpm2-smc-uart +- fsl,cpm1-scc-uart +- fsl,cpm2-scc-uart +- fsl,qe-uart + +Modem control lines connected to GPIO controllers are listed in the gpios +property as described in booting-without-of.txt, section IX.1 in the following +order: + +CTS, RTS, DCD, DSR, DTR, and RI. + +The gpios property is optional and can be left out when control lines are +not used. + +Example: + + serial@11a00 { + device_type = "serial"; + compatible = "fsl,mpc8272-scc-uart", + "fsl,cpm2-scc-uart"; + reg = <11a00 20 8000 100>; + interrupts = <28 8>; + interrupt-parent = <&PIC>; + fsl,cpm-brg = <1>; + fsl,cpm-command = <00800000>; + gpios = <&gpio_c 15 0 + &gpio_d 29 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/diu.txt b/Documentation/devicetree/bindings/powerpc/fsl/diu.txt new file mode 100644 index 00000000000..b66cb6d31d6 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/diu.txt @@ -0,0 +1,34 @@ +* Freescale Display Interface Unit + +The Freescale DIU is a LCD controller, with proper hardware, it can also +drive DVI monitors. + +Required properties: +- compatible : should be "fsl,diu" or "fsl,mpc5121-diu". +- reg : should contain at least address and length of the DIU register + set. +- interrupts : one DIU interrupt should be described here. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- edid : verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + +Example (MPC8610HPCD): + display@2c000 { + compatible = "fsl,diu"; + reg = <0x2c000 100>; + interrupts = <72 2>; + interrupt-parent = <&mpic>; + }; + +Example for MPC5121: + display@2100 { + compatible = "fsl,mpc5121-diu"; + reg = <0x2100 0x100>; + interrupts = <64 0x8>; + interrupt-parent = <&ipic>; + edid = [edid-data]; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt new file mode 100644 index 00000000000..2a4b4bce611 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt @@ -0,0 +1,144 @@ +* Freescale 83xx DMA Controller + +Freescale PowerPC 83xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8349, mpc8360, etc.) and the second is + "fsl,elo-dma" +- reg : <registers mapping for DMA general status reg> +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. +- cell-index : controller index. 0 for controller @ 0x8100 +- interrupts : <interrupt mapping for DMA IRQ> +- interrupt-parent : optional, if needed for interrupt mapping + + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8349, mpc8350, etc.) and the second is + "fsl,elo-dma-channel". However, see note below. + - reg : <registers mapping for channel> + - cell-index : dma channel index starts at 0. + +Optional properties: + - interrupts : <interrupt mapping for DMA channel IRQ> + (on 83xx this is expected to be identical to + the interrupts property of the parent node) + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@82a8 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; + reg = <0x82a8 4>; + ranges = <0 0x8100 0x1a4>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <0>; + reg = <0 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@80 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <1>; + reg = <0x80 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@100 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <2>; + reg = <0x100 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@180 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <3>; + reg = <0x180 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + }; + +* Freescale 85xx/86xx DMA Controller + +Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8540, mpc8540, etc.) and the second is + "fsl,eloplus-dma" +- reg : <registers mapping for DMA general status reg> +- cell-index : controller index. 0 for controller @ 0x21000, + 1 for controller @ 0xc000 +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8540, mpc8560, etc.) and the second is + "fsl,eloplus-dma-channel". However, see note below. + - cell-index : dma channel index starts at 0. + - reg : <registers mapping for channel> + - interrupts : <interrupt mapping for DMA channel IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; + reg = <0x21300 4>; + ranges = <0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <23 2>; + }; + }; + +Note on DMA channel compatible properties: The compatible property must say +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA +driver (fsldma). Any DMA channel used by fsldma cannot be used by another +DMA driver, such as the SSI sound drivers for the MPC8610. Therefore, any DMA +channel that should be used for another driver should not use +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel". For the SSI drivers, for +example, the compatible property should be "fsl,ssi-dma-channel". See ssi.txt +for more information. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt b/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt new file mode 100644 index 00000000000..f514f29c67d --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt @@ -0,0 +1,64 @@ +===================================================================== +E500 LAW & Coherency Module Device Tree Binding +Copyright (C) 2009 Freescale Semiconductor Inc. +===================================================================== + +Local Access Window (LAW) Node + +The LAW node represents the region of CCSR space where local access +windows are configured. For ECM based devices this is the first 4k +of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some +number of local access windows as specified by fsl,num-laws. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,ecm-law" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - fsl,num-laws + Usage: required + Value type: <u32> + Definition: The value specifies the number of local access + windows for this device. + +===================================================================== + +E500 Coherency Module Node + +The E500 LAW node represents the region of CCSR space where ECM config +and error reporting registers exist, this is the second 4k (0x1000) +of CCSR space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,CHIP-ecm", "fsl,ecm" where + CHIP is the processor (mpc8572, mpc8544, etc.) + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - interrupts + Usage: required + Value type: <prop-encoded-array> + + - interrupt-parent + Usage: required + Value type: <phandle> + +===================================================================== diff --git a/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt b/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt new file mode 100644 index 00000000000..9a33efded4b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt @@ -0,0 +1,31 @@ +* Freescale General-purpose Timers Module + +Required properties: + - compatible : should be + "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs + "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs + "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs + - reg : should contain gtm registers location and length (0x40). + - interrupts : should contain four interrupts. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies the frequency driving the timer. + +Example: + +timer@500 { + compatible = "fsl,mpc8360-gtm", "fsl,gtm"; + reg = <0x500 0x40>; + interrupts = <90 8 78 8 84 8 72 8>; + interrupt-parent = <&ipic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; + +timer@440 { + compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; + reg = <0x440 0x40>; + interrupts = <12 13 14 15>; + interrupt-parent = <&qeic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt new file mode 100644 index 00000000000..9e7a2417dac --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt @@ -0,0 +1,25 @@ +* Global Utilities Block + +The global utilities block controls power management, I/O device +enabling, power-on-reset configuration monitoring, general-purpose +I/O signal configuration, alternate function selection for multiplexed +signals, and clock control. + +Required properties: + + - compatible : Should define the compatible device type for + global-utilities. + - reg : Offset and length of the register set for the device. + +Recommended properties: + + - fsl,has-rstcr : Indicates that the global utilities register set + contains a functioning "reset control register" (i.e. the board + is wired to reset upon setting the HRESET_REQ bit in this register). + +Example: + global-utilities@e0000 { /* global utilities block */ + compatible = "fsl,mpc8548-guts"; + reg = <e0000 1000>; + fsl,has-rstcr; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt b/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt new file mode 100644 index 00000000000..3300fec501c --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt @@ -0,0 +1,35 @@ +* Chipselect/Local Bus + +Properties: +- name : Should be localbus +- #address-cells : Should be either two or three. The first cell is the + chipselect number, and the remaining cells are the + offset into the chipselect. +- #size-cells : Either one or two, depending on how large each chipselect + can be. +- ranges : Each range corresponds to a single chipselect, and cover + the entire access window as configured. + +Example: + localbus@f0010100 { + compatible = "fsl,mpc8272-localbus", + "fsl,pq2-localbus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <f0010100 40>; + + ranges = <0 0 fe000000 02000000 + 1 0 f4500000 00008000>; + + flash@0,0 { + compatible = "jedec-flash"; + reg = <0 0 2000000>; + bank-width = <4>; + device-width = <1>; + }; + + board-control@1,0 { + reg = <1 0 20>; + compatible = "fsl,mpc8272ads-bcsr"; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt b/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt new file mode 100644 index 00000000000..4ceda9b3b41 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt @@ -0,0 +1,64 @@ +===================================================================== +MPX LAW & Coherency Module Device Tree Binding +Copyright (C) 2009 Freescale Semiconductor Inc. +===================================================================== + +Local Access Window (LAW) Node + +The LAW node represents the region of CCSR space where local access +windows are configured. For MCM based devices this is the first 4k +of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some +number of local access windows as specified by fsl,num-laws. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,mcm-law" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - fsl,num-laws + Usage: required + Value type: <u32> + Definition: The value specifies the number of local access + windows for this device. + +===================================================================== + +MPX Coherency Module Node + +The MPX LAW node represents the region of CCSR space where MCM config +and error reporting registers exist, this is the second 4k (0x1000) +of CCSR space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,CHIP-mcm", "fsl,mcm" where + CHIP is the processor (mpc8641, mpc8610, etc.) + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - interrupts + Usage: required + Value type: <prop-encoded-array> + + - interrupt-parent + Usage: required + Value type: <phandle> + +===================================================================== diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt b/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt new file mode 100644 index 00000000000..0f766333b6e --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt @@ -0,0 +1,17 @@ +Freescale MPC8349E-mITX-compatible Power Management Micro Controller Unit (MCU) + +Required properties: +- compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx". +- reg : should specify I2C address (0x0a). +- #gpio-cells : should be 2. +- gpio-controller : should be present. + +Example: + +mcu@0a { + #gpio-cells = <2>; + compatible = "fsl,mc9s08qg8-mpc8349emitx", + "fsl,mcu-mpc8349emitx"; + reg = <0x0a>; + gpio-controller; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt new file mode 100644 index 00000000000..8832e879891 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt @@ -0,0 +1,70 @@ +MPC5121 PSC Device Tree Bindings + +PSC in UART mode +---------------- + +For PSC in UART mode the needed PSC serial devices +are specified by fsl,mpc5121-psc-uart nodes in the +fsl,mpc5121-immr SoC node. Additionally the PSC FIFO +Controller node fsl,mpc5121-psc-fifo is requered there: + +fsl,mpc5121-psc-uart nodes +-------------------------- + +Required properties : + - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" + - cell-index : Index of the PSC in hardware + - reg : Offset and length of the register set for the PSC device + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Recommended properties : + - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) + - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) + + +fsl,mpc5121-psc-fifo node +------------------------- + +Required properties : + - compatible : Should be "fsl,mpc5121-psc-fifo" + - reg : Offset and length of the register set for the PSC + FIFO Controller + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + + +Example for a board using PSC0 and PSC1 devices in serial mode: + +serial@11000 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <0>; + reg = <0x11000 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +serial@11100 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <1>; + reg = <0x11100 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +pscfifo@11f00 { + compatible = "fsl,mpc5121-psc-fifo"; + reg = <0x11f00 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt new file mode 100644 index 00000000000..4ccb2cd5df9 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt @@ -0,0 +1,198 @@ +MPC5200 Device Tree Bindings +---------------------------- + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +Naming conventions +------------------ +For mpc5200 on-chip devices, the format for each compatible value is +<chip>-<device>[-<mode>]. The OS should be able to match a device driver +to the device based solely on the compatible value. If two drivers +match on the compatible list; the 'most compatible' driver should be +selected. + +The split between the MPC5200 and the MPC5200B leaves a bit of a +conundrum. How should the compatible property be set up to provide +maximum compatibility information; but still accurately describe the +chip? For the MPC5200; the answer is easy. Most of the SoC devices +originally appeared on the MPC5200. Since they didn't exist anywhere +else; the 5200 compatible properties will contain only one item; +"fsl,mpc5200-<device>". + +The 5200B is almost the same as the 5200, but not quite. It fixes +silicon bugs and it adds a small number of enhancements. Most of the +devices either provide exactly the same interface as on the 5200. A few +devices have extra functions but still have a backwards compatible mode. +To express this information as completely as possible, 5200B device trees +should have two items in the compatible list: + compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>"; + +It is *strongly* recommended that 5200B device trees follow this convention +(instead of only listing the base mpc5200 item). + +ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec"; + ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec"; + +Modal devices, like PSCs, also append the configured function to the +end of the compatible field. ie. A PSC in i2s mode would specify +"fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s". This convention is chosen to +avoid naming conflicts with non-psc devices providing the same +function. For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe +the mpc5200 simple spi device and a PSC spi mode respectively. + +At the time of writing, exact chip may be either 'fsl,mpc5200' or +'fsl,mpc5200b'. + +The soc node +------------ +This node describes the on chip SOC peripherals. Every mpc5200 based +board will have this node, and as such there is a common naming +convention for SOC devices. + +Required properties: +name description +---- ----------- +ranges Memory range of the internal memory mapped registers. + Should be <0 [baseaddr] 0xc000> +reg Should be <[baseaddr] 0x100> +compatible mpc5200: "fsl,mpc5200-immr" + mpc5200b: "fsl,mpc5200b-immr" +system-frequency 'fsystem' frequency in Hz; XLB, IPB, USB and PCI + clocks are derived from the fsystem clock. +bus-frequency IPB bus frequency in Hz. Clock rate + used by most of the soc devices. + +soc child nodes +--------------- +Any on chip SOC devices available to Linux must appear as soc5200 child nodes. + +Note: The tables below show the value for the mpc5200. A mpc5200b device +tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form. + +Required soc5200 child nodes: +name compatible Description +---- ---------- ----------- +cdm@<addr> fsl,mpc5200-cdm Clock Distribution +interrupt-controller@<addr> fsl,mpc5200-pic need an interrupt + controller to boot +bestcomm@<addr> fsl,mpc5200-bestcomm Bestcomm DMA controller + +Recommended soc5200 child nodes; populate as needed for your board +name compatible Description +---- ---------- ----------- +timer@<addr> fsl,mpc5200-gpt General purpose timers +gpio@<addr> fsl,mpc5200-gpio MPC5200 simple gpio controller +gpio@<addr> fsl,mpc5200-gpio-wkup MPC5200 wakeup gpio controller +rtc@<addr> fsl,mpc5200-rtc Real time clock +mscan@<addr> fsl,mpc5200-mscan CAN bus controller +pci@<addr> fsl,mpc5200-pci PCI bridge +serial@<addr> fsl,mpc5200-psc-uart PSC in serial mode +i2s@<addr> fsl,mpc5200-psc-i2s PSC in i2s mode +ac97@<addr> fsl,mpc5200-psc-ac97 PSC in ac97 mode +spi@<addr> fsl,mpc5200-psc-spi PSC in spi mode +irda@<addr> fsl,mpc5200-psc-irda PSC in IrDA mode +spi@<addr> fsl,mpc5200-spi MPC5200 spi device +ethernet@<addr> fsl,mpc5200-fec MPC5200 ethernet device +ata@<addr> fsl,mpc5200-ata IDE ATA interface +i2c@<addr> fsl,mpc5200-i2c I2C controller +usb@<addr> fsl,mpc5200-ohci,ohci-be USB controller +xlb@<addr> fsl,mpc5200-xlb XLB arbitrator + +fsl,mpc5200-gpt nodes +--------------------- +On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board +design supports the internal wdt, then the device node for GPT0 should +include the empty property 'fsl,has-wdt'. Note that this does not activate +the watchdog. The timer will function as a GPT if the timer api is used, and +it will function as watchdog if the watchdog device is used. The watchdog +mode has priority over the gpt mode, i.e. if the watchdog is activated, any +gpt api call to this timer will fail with -EBUSY. + +If you add the property + fsl,wdt-on-boot = <n>; +GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. +If n>0, the watchdog is started with a timeout of n seconds. If n=0, the +configuration of the watchdog is not touched. This is useful in two cases: +- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; +- do not touch a configuration assigned by the boot loader which supervises + the boot process itself. + +The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. + +An mpc5200-gpt can be used as a single line GPIO controller. To do so, +add the following properties to the gpt node: + gpio-controller; + #gpio-cells = <2>; +When referencing the GPIO line from another node, the first cell must always +be zero and the second cell represents the gpio flags and described in the +gpio device tree binding. + +An mpc5200-gpt can be used as a single line edge sensitive interrupt +controller. To do so, add the following properties to the gpt node: + interrupt-controller; + #interrupt-cells = <1>; +When referencing the IRQ line from another node, the cell represents the +sense mode; 1 for edge rising, 2 for edge falling. + +fsl,mpc5200-psc nodes +--------------------- +The PSCs should include a cell-index which is the index of the PSC in +hardware. cell-index is used to determine which shared SoC registers to +use when setting up PSC clocking. cell-index number starts at '0'. ie: + PSC1 has 'cell-index = <0>' + PSC4 has 'cell-index = <3>' + +PSC in i2s mode: The mpc5200 and mpc5200b PSCs are not compatible when in +i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the +compatible field. + + +fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes +------------------------------------------------ +Each GPIO controller node should have the empty property gpio-controller and +#gpio-cells set to 2. First cell is the GPIO number which is interpreted +according to the bit numbers in the GPIO control registers. The second cell +is for flags which is currently unused. + +fsl,mpc5200-fec nodes +--------------------- +The FEC node can specify one of the following properties to configure +the MII link: +- fsl,7-wire-mode - An empty property that specifies the link uses 7-wire + mode instead of MII +- current-speed - Specifies that the MII should be configured for a fixed + speed. This property should contain two cells. The + first cell specifies the speed in Mbps and the second + should be '0' for half duplex and '1' for full duplex +- phy-handle - Contains a phandle to an Ethernet PHY. + +Interrupt controller (fsl,mpc5200-pic) node +------------------------------------------- +The mpc5200 pic binding splits hardware IRQ numbers into two levels. The +split reflects the layout of the PIC hardware itself, which groups +interrupts into one of three groups; CRIT, MAIN or PERP. Also, the +Bestcomm dma engine has it's own set of interrupt sources which are +cascaded off of peripheral interrupt 0, which the driver interprets as a +fourth group, SDMA. + +The interrupts property for device nodes using the mpc5200 pic consists +of three cells; <L1 L2 level> + + L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3] + L2 := interrupt number; directly mapped from the value in the + "ICTL PerStat, MainStat, CritStat Encoded Register" + level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3] + +For external IRQs, use the following interrupt property values (how to +specify external interrupts is a frequently asked question): +External interrupts: + external irq0: interrupts = <0 0 n>; + external irq1: interrupts = <1 1 n>; + external irq2: interrupts = <1 2 n>; + external irq3: interrupts = <1 3 n>; +'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) + +fsl,mpc5200-mscan nodes +----------------------- +See file can.txt in this directory. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt new file mode 100644 index 00000000000..71e39cf3215 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt @@ -0,0 +1,42 @@ +* OpenPIC and its interrupt numbers on Freescale's e500/e600 cores + +The OpenPIC specification does not specify which interrupt source has to +become which interrupt number. This is up to the software implementation +of the interrupt controller. The only requirement is that every +interrupt source has to have an unique interrupt number / vector number. +To accomplish this the current implementation assigns the number zero to +the first source, the number one to the second source and so on until +all interrupt sources have their unique number. +Usually the assigned vector number equals the interrupt number mentioned +in the documentation for a given core / CPU. This is however not true +for the e500 cores (MPC85XX CPUs) where the documentation distinguishes +between internal and external interrupt sources and starts counting at +zero for both of them. + +So what to write for external interrupt source X or internal interrupt +source Y into the device tree? Here is an example: + +The memory map for the interrupt controller in the MPC8544[0] shows, +that the first interrupt source starts at 0x5_0000 (PIC Register Address +Map-Interrupt Source Configuration Registers). This source becomes the +number zero therefore: + External interrupt 0 = interrupt number 0 + External interrupt 1 = interrupt number 1 + External interrupt 2 = interrupt number 2 + ... +Every interrupt number allocates 0x20 bytes register space. So to get +its number it is sufficient to shift the lower 16bits to right by five. +So for the external interrupt 10 we have: + 0x0140 >> 5 = 10 + +After the external sources, the internal sources follow. The in core I2C +controller on the MPC8544 for instance has the internal source number +27. Oo obtain its interrupt number we take the lower 16bits of its memory +address (0x5_0560) and shift it right: + 0x0560 >> 5 = 43 + +Therefore the I2C device node for the MPC8544 CPU has to have the +interrupt number 43 specified in the device tree. + +[0] MPC8544E PowerQUICCTM III, Integrated Host Processor Family Reference Manual + MPC8544ERM Rev. 1 10/2007 diff --git a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt new file mode 100644 index 00000000000..bcc30bac683 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt @@ -0,0 +1,36 @@ +* Freescale MSI interrupt controller + +Required properties: +- compatible : compatible list, contains 2 entries, + first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, + etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on + the parent type. +- reg : should contain the address and the length of the shared message + interrupt register set. +- msi-available-ranges: use <start count> style section to define which + msi interrupt can be used in the 256 msi interrupts. This property is + optional, without this, all the 256 MSI interrupts can be used. +- interrupts : each one of the interrupts here is one entry per 32 MSIs, + and routed to the host interrupt controller. the interrupts should + be set as edge sensitive. +- interrupt-parent: the phandle for the interrupt controller + that services interrupts for this device. for 83xx cpu, the interrupts + are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed + to MPIC. + +Example: + msi@41600 { + compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + interrupt-parent = <&mpic>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt b/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt new file mode 100644 index 00000000000..07256b7ffca --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt @@ -0,0 +1,63 @@ +* Power Management Controller + +Properties: +- compatible: "fsl,<chip>-pmc". + + "fsl,mpc8349-pmc" should be listed for any chip whose PMC is + compatible. "fsl,mpc8313-pmc" should also be listed for any chip + whose PMC is compatible, and implies deep-sleep capability. + + "fsl,mpc8548-pmc" should be listed for any chip whose PMC is + compatible. "fsl,mpc8536-pmc" should also be listed for any chip + whose PMC is compatible, and implies deep-sleep capability. + + "fsl,mpc8641d-pmc" should be listed for any chip whose PMC is + compatible; all statements below that apply to "fsl,mpc8548-pmc" also + apply to "fsl,mpc8641d-pmc". + + Compatibility does not include bit assignments in SCCR/PMCDR/DEVDISR; these + bit assignments are indicated via the sleep specifier in each device's + sleep property. + +- reg: For devices compatible with "fsl,mpc8349-pmc", the first resource + is the PMC block, and the second resource is the Clock Configuration + block. + + For devices compatible with "fsl,mpc8548-pmc", the first resource + is a 32-byte block beginning with DEVDISR. + +- interrupts: For "fsl,mpc8349-pmc"-compatible devices, the first + resource is the PMC block interrupt. + +- fsl,mpc8313-wakeup-timer: For "fsl,mpc8313-pmc"-compatible devices, + this is a phandle to an "fsl,gtm" node on which timer 4 can be used as + a wakeup source from deep sleep. + +Sleep specifiers: + + fsl,mpc8349-pmc: Sleep specifiers consist of one cell. For each bit + that is set in the cell, the corresponding bit in SCCR will be saved + and cleared on suspend, and restored on resume. This sleep controller + supports disabling and resuming devices at any time. + + fsl,mpc8536-pmc: Sleep specifiers consist of three cells, the third of + which will be ORed into PMCDR upon suspend, and cleared from PMCDR + upon resume. The first two cells are as described for fsl,mpc8578-pmc. + This sleep controller only supports disabling devices during system + sleep, or permanently. + + fsl,mpc8548-pmc: Sleep specifiers consist of one or two cells, the + first of which will be ORed into DEVDISR (and the second into + DEVDISR2, if present -- this cell should be zero or absent if the + hardware does not have DEVDISR2) upon a request for permanent device + disabling. This sleep controller does not support configuring devices + to disable during system sleep (unless supported by another compatible + match), or dynamically. + +Example: + + power@b00 { + compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc"; + reg = <0xb00 0x100 0xa00 0x100>; + interrupts = <80 8>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/sec.txt b/Documentation/devicetree/bindings/powerpc/fsl/sec.txt new file mode 100644 index 00000000000..2b6f2d45c45 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/sec.txt @@ -0,0 +1,68 @@ +Freescale SoC SEC Security Engines + +Required properties: + +- compatible : Should contain entries for this and backward compatible + SEC versions, high to low, e.g., "fsl,sec2.1", "fsl,sec2.0" +- reg : Offset and length of the register set for the device +- interrupts : the SEC's interrupt number +- fsl,num-channels : An integer representing the number of channels + available. +- fsl,channel-fifo-len : An integer representing the number of + descriptor pointers each channel fetch fifo can hold. +- fsl,exec-units-mask : The bitmask representing what execution units + (EUs) are available. It's a single 32-bit cell. EU information + should be encoded following the SEC's Descriptor Header Dword + EU_SEL0 field documentation, i.e. as follows: + + bit 0 = reserved - should be 0 + bit 1 = set if SEC has the ARC4 EU (AFEU) + bit 2 = set if SEC has the DES/3DES EU (DEU) + bit 3 = set if SEC has the message digest EU (MDEU/MDEU-A) + bit 4 = set if SEC has the random number generator EU (RNG) + bit 5 = set if SEC has the public key EU (PKEU) + bit 6 = set if SEC has the AES EU (AESU) + bit 7 = set if SEC has the Kasumi EU (KEU) + bit 8 = set if SEC has the CRC EU (CRCU) + bit 11 = set if SEC has the message digest EU extended alg set (MDEU-B) + +remaining bits are reserved for future SEC EUs. + +- fsl,descriptor-types-mask : The bitmask representing what descriptors + are available. It's a single 32-bit cell. Descriptor type information + should be encoded following the SEC's Descriptor Header Dword DESC_TYPE + field documentation, i.e. as follows: + + bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type + bit 1 = set if SEC supports the ipsec_esp descriptor type + bit 2 = set if SEC supports the common_nonsnoop desc. type + bit 3 = set if SEC supports the 802.11i AES ccmp desc. type + bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type + bit 5 = set if SEC supports the srtp descriptor type + bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type + bit 7 = set if SEC supports the pkeu_assemble descriptor type + bit 8 = set if SEC supports the aesu_key_expand_output desc.type + bit 9 = set if SEC supports the pkeu_ptmul descriptor type + bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type + bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type + + ..and so on and so forth. + +Optional properties: + +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Example: + + /* MPC8548E */ + crypto@30000 { + compatible = "fsl,sec2.1", "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <29 2>; + interrupt-parent = <&mpic>; + fsl,num-channels = <4>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0xfe>; + fsl,descriptor-types-mask = <0x12b0ebf>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt new file mode 100644 index 00000000000..5ff76c9c57d --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt @@ -0,0 +1,73 @@ +Freescale Synchronous Serial Interface + +The SSI is a serial device that communicates with audio codecs. It can +be programmed in AC97, I2S, left-justified, or right-justified modes. + +Required properties: +- compatible: Compatible list, contains "fsl,ssi". +- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. +- reg: Offset and length of the register set for the device. +- interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and + level information for the interrupt. This should be + encoded based on the information in section 2) + depending on the type of interrupt controller you + have. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this device. +- fsl,mode: The operating mode for the SSI interface. + "i2s-slave" - I2S mode, SSI is clock slave + "i2s-master" - I2S mode, SSI is clock master + "lj-slave" - left-justified mode, SSI is clock slave + "lj-master" - l.j. mode, SSI is clock master + "rj-slave" - right-justified mode, SSI is clock slave + "rj-master" - r.j., SSI is clock master + "ac97-slave" - AC97 mode, SSI is clock slave + "ac97-master" - AC97 mode, SSI is clock master +- fsl,playback-dma: Phandle to a node for the DMA channel to use for + playback of audio. This is typically dictated by SOC + design. See the notes below. +- fsl,capture-dma: Phandle to a node for the DMA channel to use for + capture (recording) of audio. This is typically dictated + by SOC design. See the notes below. +- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. + This number is the maximum allowed value for SFCSR[TFWM0]. +- fsl,ssi-asynchronous: + If specified, the SSI is to be programmed in asynchronous + mode. In this mode, pins SRCK, STCK, SRFS, and STFS must + all be connected to valid signals. In synchronous mode, + SRCK and SRFS are ignored. Asynchronous mode allows + playback and capture to use different sample sizes and + sample rates. Some drivers may require that SRCK and STCK + be connected together, and SRFS and STFS be connected + together. This would still allow different sample sizes, + but not different sample rates. + +Optional properties: +- codec-handle: Phandle to a 'codec' node that defines an audio + codec connected to this SSI. This node is typically + a child of an I2C or other control node. + +Child 'codec' node required properties: +- compatible: Compatible list, contains the name of the codec + +Child 'codec' node optional properties: +- clock-frequency: The frequency of the input clock, which typically comes + from an on-board dedicated oscillator. + +Notes on fsl,playback-dma and fsl,capture-dma: + +On SOCs that have an SSI, specific DMA channels are hard-wired for playback +and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for +playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for +playback and DMA channel 3 for capture. The developer can choose which +DMA controller to use, but the channels themselves are hard-wired. The +purpose of these two properties is to represent this hardware design. + +The device tree nodes for the DMA channels that are referenced by +"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with +"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. +"fsl,mpc8610-dma-channel") can remain. If these nodes are left as +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA +drivers (fsldma) will attempt to use them, and it will conflict with the +sound drivers. diff --git a/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt b/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt new file mode 100644 index 00000000000..b558585b1aa --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/nintendo/gamecube.txt @@ -0,0 +1,109 @@ + +Nintendo GameCube device tree +============================= + +1) The "flipper" node + + This node represents the multi-function "Flipper" chip, which packages + many of the devices found in the Nintendo GameCube. + + Required properties: + + - compatible : Should be "nintendo,flipper" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the interrupt controller within the "Flipper" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - compatible : should be "nintendo,flipper-pic" + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.c.i) The Auxiliary RAM (ARAM) node + + Represents the non cpu-addressable ram designed mainly to store audio + related information. + The ARAM node must be placed under the DSP node. + + Required properties: + + - compatible : should be "nintendo,flipper-aram" + - reg : should contain the ARAM start (zero-based) and length + +1.d) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,flipper-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.g) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + diff --git a/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt b/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt new file mode 100644 index 00000000000..a7e155a023b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/nintendo/wii.txt @@ -0,0 +1,184 @@ + +Nintendo Wii device tree +======================== + +0) The root node + + This node represents the Nintendo Wii video game console. + + Required properties: + + - model : Should be "nintendo,wii" + - compatible : Should be "nintendo,wii" + +1) The "hollywood" node + + This node represents the multi-function "Hollywood" chip, which packages + many of the devices found in the Nintendo Wii. + + Required properties: + + - compatible : Should be "nintendo,hollywood" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,hollywood-vi","nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,hollywood-pi","nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the "Flipper" interrupt controller within the "Hollywood" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,flipper-pic" + - interrupt-controller + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,hollywood-dsp","nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.d) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-si","nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,hollywood-ai","nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-exi","nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + +1.g) The Open Host Controller Interface (OHCI) nodes + + Represent the USB 1.x Open Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ohci","usb-ohci" + - reg : should contain the OHCI registers location and length + - interrupts : should contain the OHCI interrupt + +1.h) The Enhanced Host Controller Interface (EHCI) node + + Represents the USB 2.0 Enhanced Host Controller Interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ehci","usb-ehci" + - reg : should contain the EHCI registers location and length + - interrupts : should contain the EHCI interrupt + +1.i) The Secure Digital Host Controller Interface (SDHCI) nodes + + Represent the Secure Digital Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-sdhci","sdhci" + - reg : should contain the SDHCI registers location and length + - interrupts : should contain the SDHCI interrupt + +1.j) The Inter-Processsor Communication (IPC) node + + Represent the Inter-Processor Communication interface. This interface + enables communications between the Broadway and the Starlet processors. + + - compatible : should be "nintendo,hollywood-ipc" + - reg : should contain the IPC registers location and length + - interrupts : should contain the IPC interrupt + +1.k) The "Hollywood" interrupt controller node + + Represents the "Hollywood" interrupt controller within the + "Hollywood" chip. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,hollywood-pic" + - reg : should contain the controller registers location and length + - interrupt-controller + - interrupts : should contain the cascade interrupt of the "flipper" pic + - interrupt-parent: should contain the phandle of the "flipper" pic + +1.l) The General Purpose I/O (GPIO) controller node + + Represents the dual access 32 GPIO controller interface. + + Required properties: + + - #gpio-cells : <2> + - compatible : should be "nintendo,hollywood-gpio" + - reg : should contain the IPC registers location and length + - gpio-controller + +1.m) The control node + + Represents the control interface used to setup several miscellaneous + settings of the "Hollywood" chip like boot memory mappings, resets, + disk interface mode, etc. + + Required properties: + + - compatible : should be "nintendo,hollywood-control" + - reg : should contain the control registers location and length + +1.n) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,hollywood-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt new file mode 100644 index 00000000000..777abd7399d --- /dev/null +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -0,0 +1,53 @@ +* SPI (Serial Peripheral Interface) + +Required properties: +- cell-index : QE SPI subblock index. + 0: QE subblock SPI1 + 1: QE subblock SPI2 +- compatible : should be "fsl,spi". +- mode : the SPI operation mode, it can be "cpu" or "cpu-qe". +- reg : Offset and length of the register set for the device +- interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- gpios : specifies the gpio pins to be used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. + +Example: + spi@4c0 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <4c0 40>; + interrupts = <82 0>; + interrupt-parent = <700>; + mode = "cpu"; + gpios = <&gpio 18 1 // device reg=<0> + &gpio 19 1>; // device reg=<1> + }; + + +* eSPI (Enhanced Serial Peripheral Interface) + +Required properties: +- compatible : should be "fsl,mpc8536-espi". +- reg : Offset and length of the register set for the device. +- interrupts : should contain eSPI interrupt, the device has one interrupt. +- fsl,espi-num-chipselects : the number of the chipselect signals. + +Example: + spi@110000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc8536-espi"; + reg = <0x110000 0x1000>; + interrupts = <53 0x2>; + interrupt-parent = <&mpic>; + fsl,espi-num-chipselects = <4>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt new file mode 100644 index 00000000000..e782add2e45 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -0,0 +1,57 @@ +SPI (Serial Peripheral Interface) busses + +SPI busses can be described with a node for the SPI master device +and a set of child nodes for each SPI slave on the bus. For this +discussion, it is assumed that the system's SPI controller is in +SPI master mode. This binding does not describe SPI controllers +in slave mode. + +The SPI master node requires the following properties: +- #address-cells - number of cells required to define a chip select + address on the SPI bus. +- #size-cells - should be zero. +- compatible - name of SPI bus controller following generic names + recommended practice. +No other properties are required in the SPI bus node. It is assumed +that a driver for an SPI bus device will understand that it is an SPI bus. +However, the binding does not attempt to define the specific method for +assigning chip select numbers. Since SPI chip select configuration is +flexible and non-standardized, it is left out of this binding with the +assumption that board specific platform code will be used to manage +chip selects. Individual drivers can define additional properties to +support describing the chip select layout. + +SPI slave nodes must be children of the SPI master node and can +contain the following properties. +- reg - (required) chip select address of device. +- compatible - (required) name of SPI device following generic names + recommended practice +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz +- spi-cpol - (optional) Empty property indicating device requires + inverse clock polarity (CPOL) mode +- spi-cpha - (optional) Empty property indicating device requires + shifted clock phase (CPHA) mode +- spi-cs-high - (optional) Empty property indicating device requires + chip select active high + +SPI example for an MPC5200 SPI bus: + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/fsl-usb.txt b/Documentation/devicetree/bindings/usb/fsl-usb.txt new file mode 100644 index 00000000000..bd5723f0b67 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/fsl-usb.txt @@ -0,0 +1,81 @@ +Freescale SOC USB controllers + +The device node for a USB controller that is part of a Freescale +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : Should be "fsl-usb2-mph" for multi port host USB + controllers, or "fsl-usb2-dr" for dual role USB controllers + or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121 + - phy_type : For multi port host USB controllers, should be one of + "ulpi", or "serial". For dual role USB controllers, should be + one of "ulpi", "utmi", "utmi_wide", or "serial". + - reg : Offset and length of the register set for the device + - port0 : boolean; if defined, indicates port0 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port1" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - port1 : boolean; if defined, indicates port1 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port0" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible + controllers. Can be "host", "peripheral", or "otg". Default to + "host" if not defined for backward compatibility. + +Recommended properties : + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties : + - fsl,invert-drvvbus : boolean; for MPC5121 USB0 only. Indicates the + port power polarity of internal PHY signal DRVVBUS is inverted. + - fsl,invert-pwr-fault : boolean; for MPC5121 USB0 only. Indicates + the PWR_FAULT signal polarity is inverted. + +Example multi port host USB controller device node : + usb@22000 { + compatible = "fsl-usb2-mph"; + reg = <22000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <27 1>; + phy_type = "ulpi"; + port0; + port1; + }; + +Example dual role USB controller device node : + usb@23000 { + compatible = "fsl-usb2-dr"; + reg = <23000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <26 1>; + dr_mode = "otg"; + phy = "ulpi"; + }; + +Example dual role USB controller device node for MPC5121ADS: + + usb@4000 { + compatible = "fsl,mpc5121-usb2-dr"; + reg = <0x4000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = < &ipic >; + interrupts = <44 0x8>; + dr_mode = "otg"; + phy_type = "utmi_wide"; + fsl,invert-drvvbus; + fsl,invert-pwr-fault; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt new file mode 100644 index 00000000000..fa18612f757 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -0,0 +1,25 @@ +USB EHCI controllers + +Required properties: + - compatible : should be "usb-ehci". + - reg : should contain at least address and length of the standard EHCI + register set for the device. Optional platform-dependent registers + (debug-port or other) can be also specified here, but only after + definition of standard EHCI registers. + - interrupts : one EHCI interrupt should be described here. +If device registers are implemented in big endian mode, the device +node should have "big-endian-regs" property. +If controller implementation operates with big endian descriptors, +"big-endian-desc" property should be specified. +If both big endian registers and descriptors are used by the controller +implementation, "big-endian" property can be specified instead of having +both "big-endian-regs" and "big-endian-desc". + +Example (Sequoia 440EPx): + ehci@e0000300 { + compatible = "ibm,usb-ehci-440epx", "usb-ehci"; + interrupt-parent = <&UIC0>; + interrupts = <1a 4>; + reg = <0 e0000300 90 0 e0000390 70>; + big-endian; + }; diff --git a/Documentation/devicetree/bindings/xilinx.txt b/Documentation/devicetree/bindings/xilinx.txt new file mode 100644 index 00000000000..299d0923537 --- /dev/null +++ b/Documentation/devicetree/bindings/xilinx.txt @@ -0,0 +1,306 @@ + d) Xilinx IP cores + + The Xilinx EDK toolchain ships with a set of IP cores (devices) for use + in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range + of standard device types (network, serial, etc.) and miscellaneous + devices (gpio, LCD, spi, etc). Also, since these devices are + implemented within the fpga fabric every instance of the device can be + synthesised with different options that change the behaviour. + + Each IP-core has a set of parameters which the FPGA designer can use to + control how the core is synthesized. Historically, the EDK tool would + extract the device parameters relevant to device drivers and copy them + into an 'xparameters.h' in the form of #define symbols. This tells the + device drivers how the IP cores are configured, but it requires the kernel + to be recompiled every time the FPGA bitstream is resynthesized. + + The new approach is to export the parameters into the device tree and + generate a new device tree each time the FPGA bitstream changes. The + parameters which used to be exported as #defines will now become + properties of the device node. In general, device nodes for IP-cores + will take the following form: + + (name): (generic-name)@(base-address) { + compatible = "xlnx,(ip-core-name)-(HW_VER)" + [, (list of compatible devices), ...]; + reg = <(baseaddr) (size)>; + interrupt-parent = <&interrupt-controller-phandle>; + interrupts = < ... >; + xlnx,(parameter1) = "(string-value)"; + xlnx,(parameter2) = <(int-value)>; + }; + + (generic-name): an open firmware-style name that describes the + generic class of device. Preferably, this is one word, such + as 'serial' or 'ethernet'. + (ip-core-name): the name of the ip block (given after the BEGIN + directive in system.mhs). Should be in lowercase + and all underscores '_' converted to dashes '-'. + (name): is derived from the "PARAMETER INSTANCE" value. + (parameter#): C_* parameters from system.mhs. The C_ prefix is + dropped from the parameter name, the name is converted + to lowercase and all underscore '_' characters are + converted to dashes '-'. + (baseaddr): the baseaddr parameter value (often named C_BASEADDR). + (HW_VER): from the HW_VER parameter. + (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1). + + Typically, the compatible list will include the exact IP core version + followed by an older IP core version which implements the same + interface or any other device with the same interface. + + 'reg', 'interrupt-parent' and 'interrupts' are all optional properties. + + For example, the following block from system.mhs: + + BEGIN opb_uartlite + PARAMETER INSTANCE = opb_uartlite_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BAUDRATE = 115200 + PARAMETER C_DATA_BITS = 8 + PARAMETER C_ODD_PARITY = 0 + PARAMETER C_USE_PARITY = 0 + PARAMETER C_CLK_FREQ = 50000000 + PARAMETER C_BASEADDR = 0xEC100000 + PARAMETER C_HIGHADDR = 0xEC10FFFF + BUS_INTERFACE SOPB = opb_7 + PORT OPB_Clk = CLK_50MHz + PORT Interrupt = opb_uartlite_0_Interrupt + PORT RX = opb_uartlite_0_RX + PORT TX = opb_uartlite_0_TX + PORT OPB_Rst = sys_bus_reset_0 + END + + becomes the following device tree node: + + opb_uartlite_0: serial@ec100000 { + device_type = "serial"; + compatible = "xlnx,opb-uartlite-1.00.b"; + reg = <ec100000 10000>; + interrupt-parent = <&opb_intc_0>; + interrupts = <1 0>; // got this from the opb_intc parameters + current-speed = <d#115200>; // standard serial device prop + clock-frequency = <d#50000000>; // standard serial device prop + xlnx,data-bits = <8>; + xlnx,odd-parity = <0>; + xlnx,use-parity = <0>; + }; + + Some IP cores actually implement 2 or more logical devices. In + this case, the device should still describe the whole IP core with + a single node and add a child node for each logical device. The + ranges property can be used to translate from parent IP-core to the + registers of each device. In addition, the parent node should be + compatible with the bus type 'xlnx,compound', and should contain + #address-cells and #size-cells, as with any other bus. (Note: this + makes the assumption that both logical devices have the same bus + binding. If this is not true, then separate nodes should be used + for each logical device). The 'cell-index' property can be used to + enumerate logical devices within an IP core. For example, the + following is the system.mhs entry for the dual ps2 controller found + on the ml403 reference design. + + BEGIN opb_ps2_dual_ref + PARAMETER INSTANCE = opb_ps2_dual_ref_0 + PARAMETER HW_VER = 1.00.a + PARAMETER C_BASEADDR = 0xA9000000 + PARAMETER C_HIGHADDR = 0xA9001FFF + BUS_INTERFACE SOPB = opb_v20_0 + PORT Sys_Intr1 = ps2_1_intr + PORT Sys_Intr2 = ps2_2_intr + PORT Clkin1 = ps2_clk_rx_1 + PORT Clkin2 = ps2_clk_rx_2 + PORT Clkpd1 = ps2_clk_tx_1 + PORT Clkpd2 = ps2_clk_tx_2 + PORT Rx1 = ps2_d_rx_1 + PORT Rx2 = ps2_d_rx_2 + PORT Txpd1 = ps2_d_tx_1 + PORT Txpd2 = ps2_d_tx_2 + END + + It would result in the following device tree nodes: + + opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,compound"; + ranges = <0 a9000000 2000>; + // If this device had extra parameters, then they would + // go here. + ps2@0 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <0 40>; + interrupt-parent = <&opb_intc_0>; + interrupts = <3 0>; + cell-index = <0>; + }; + ps2@1000 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <1000 40>; + interrupt-parent = <&opb_intc_0>; + interrupts = <3 0>; + cell-index = <0>; + }; + }; + + Also, the system.mhs file defines bus attachments from the processor + to the devices. The device tree structure should reflect the bus + attachments. Again an example; this system.mhs fragment: + + BEGIN ppc405_virtex4 + PARAMETER INSTANCE = ppc405_0 + PARAMETER HW_VER = 1.01.a + BUS_INTERFACE DPLB = plb_v34_0 + BUS_INTERFACE IPLB = plb_v34_0 + END + + BEGIN opb_intc + PARAMETER INSTANCE = opb_intc_0 + PARAMETER HW_VER = 1.00.c + PARAMETER C_BASEADDR = 0xD1000FC0 + PARAMETER C_HIGHADDR = 0xD1000FDF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN opb_uart16550 + PARAMETER INSTANCE = opb_uart16550_0 + PARAMETER HW_VER = 1.00.d + PARAMETER C_BASEADDR = 0xa0000000 + PARAMETER C_HIGHADDR = 0xa0001FFF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN plb_v34 + PARAMETER INSTANCE = plb_v34_0 + PARAMETER HW_VER = 1.02.a + END + + BEGIN plb_bram_if_cntlr + PARAMETER INSTANCE = plb_bram_if_cntlr_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BASEADDR = 0xFFFF0000 + PARAMETER C_HIGHADDR = 0xFFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + END + + BEGIN plb2opb_bridge + PARAMETER INSTANCE = plb2opb_bridge_0 + PARAMETER HW_VER = 1.01.a + PARAMETER C_RNG0_BASEADDR = 0x20000000 + PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF + PARAMETER C_RNG1_BASEADDR = 0x60000000 + PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF + PARAMETER C_RNG2_BASEADDR = 0x80000000 + PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF + PARAMETER C_RNG3_BASEADDR = 0xC0000000 + PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + BUS_INTERFACE MOPB = opb_v20_0 + END + + Gives this device tree (some properties removed for clarity): + + plb@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,plb-v34-1.02.a"; + device_type = "ibm,plb"; + ranges; // 1:1 translation + + plb_bram_if_cntrl_0: bram@ffff0000 { + reg = <ffff0000 10000>; + } + + opb@20000000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <20000000 20000000 20000000 + 60000000 60000000 20000000 + 80000000 80000000 40000000 + c0000000 c0000000 20000000>; + + opb_uart16550_0: serial@a0000000 { + reg = <a00000000 2000>; + }; + + opb_intc_0: interrupt-controller@d1000fc0 { + reg = <d1000fc0 20>; + }; + }; + }; + + That covers the general approach to binding xilinx IP cores into the + device tree. The following are bindings for specific devices: + + i) Xilinx ML300 Framebuffer + + Simple framebuffer device from the ML300 reference design (also on the + ML403 reference design as well as others). + + Optional properties: + - resolution = <xres yres> : pixel resolution of framebuffer. Some + implementations use a different resolution. + Default is <d#640 d#480> + - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory. + Default is <d#1024 d#480>. + - rotate-display (empty) : rotate display 180 degrees. + + ii) Xilinx SystemACE + + The Xilinx SystemACE device is used to program FPGAs from an FPGA + bitstream stored on a CF card. It can also be used as a generic CF + interface device. + + Optional properties: + - 8-bit (empty) : Set this property for SystemACE in 8 bit mode + + iii) Xilinx EMAC and Xilinx TEMAC + + Xilinx Ethernet devices. In addition to general xilinx properties + listed above, nodes for these devices should include a phy-handle + property, and may include other common network device properties + like local-mac-address. + + iv) Xilinx Uartlite + + Xilinx uartlite devices are simple fixed speed serial ports. + + Required properties: + - current-speed : Baud rate of uartlite + + v) Xilinx hwicap + + Xilinx hwicap devices provide access to the configuration logic + of the FPGA through the Internal Configuration Access Port + (ICAP). The ICAP enables partial reconfiguration of the FPGA, + readback of the configuration information, and some control over + 'warm boots' of the FPGA fabric. + + Required properties: + - xlnx,family : The family of the FPGA, necessary since the + capabilities of the underlying ICAP hardware + differ between different families. May be + 'virtex2p', 'virtex4', or 'virtex5'. + + vi) Xilinx Uart 16550 + + Xilinx UART 16550 devices are very similar to the NS16550 but with + different register spacing and an offset from the base address. + + Required properties: + - clock-frequency : Frequency of the clock input + - reg-offset : A value of 3 is required + - reg-shift : A value of 2 is required + + vii) Xilinx USB Host controller + + The Xilinx USB host controller is EHCI compatible but with a different + base address for the EHCI registers, and it is always a big-endian + USB Host controller. The hardware can be configured as high speed only, + or high speed/full speed hybrid. + + Required properties: + - xlnx,support-usb-fs: A value 0 means the core is built as high speed + only. A value 1 means the core also supports + full speed devices. + |