Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linux

Pull DRM updates from Dave Airlie:
 "Like all good pull reqs this ends with a revert, so it must mean we
  tested it,

[ Ed. That's _one_ way of looking at it ]

  This pull is missing nouveau, Ben has been stuck trying to track down
  a very longstanding bug that revealed itself due to some other
  changes.  I've asked him to send you a direct pull request for nouveau
  once he cleans things up.  I'm away until Monday so don't want to
  delay things, you can make a decision on that when he sends it, I have
  my phone so I can ack things just not really merge much.

  It has one trivial conflict with your tree in armada_drv.c, and also
  the pull request contains some component changes that are already in
  your tree, the base tree from Russell went via Greg's tree already,
  but some stuff still shows up in here that doesn't when I merge my
  tree into yours.

  Otherwise all pretty standard graphics fare, one new driver and
  changes all over the place.

  New drivers:
   - sti kms driver for STMicroelectronics chipsets stih416 and stih407.

  core:
   - lots of cleanups to the drm core
   - DP MST helper code merged
   - universal cursor planes.
   - render nodes enabled by default

  panel:
   - better panel interfaces
   - new panel support
   - non-continuous cock advertising ability

  ttm:
   - shrinker fixes

  i915:
   - hopefully ditched UMS support
   - runtime pm fixes
   - psr tracking and locking - now enabled by default
   - userptr fixes
   - backlight brightness fixes
   - MST support merged
   - runtime PM for dpms
   - primary planes locking fixes
   - gen8 hw semaphore support
   - fbc fixes
   - runtime PM on SOix sleep state hw.
   - mmio base page flipping
   - lots of vlv/chv fixes.
   - universal cursor planes

  radeon:
   - Hawaii fixes
   - display scalar support for non-fixed mode displays
   - new firmware format support
   - dpm on more asics by default
   - GPUVM improvements
   - uncached and wc GTT buffers
   - BOs > visible VRAM

  exynos:
   - i80 interface support
   - module auto-loading
   - ipp driver consolidated.

  armada:
   - irq handling in crtc layer only
   - crtc renumbering
   - add component support
   - DT interaction changes.

  tegra:
   - load as module fixes
   - eDP bpp and sync polarity fixed
   - DSI non-continuous clock mode support
   - better support for importing buffers from nouveau

  msm:
   - mdp5/adq8084 v1.3 hw enablement
   - devicetree clk changse
   - ifc6410 board working

  tda998x:
   - component support
   - DT documentation update

  vmwgfx:
   - fix compat shader namespace"

* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
  Revert "drm: drop redundant drm_file->is_master"
  drm/panel: simple: Use devm_gpiod_get_optional()
  drm/dsi: Replace upcasting macro by function
  drm/panel: ld9040: Replace upcasting macro by function
  drm/exynos: dp: Modify driver to support drm_panel
  drm/exynos: Move DP setup into commit()
  drm/panel: simple: Add AUO B133HTN01 panel support
  drm/panel: simple: Support delays in panel functions
  drm/panel: simple: Add proper definition for prepare and unprepare
  drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
  drm/panel: ld9040: Add proper definition for prepare and unprepare
  drm/tegra: Add support for panel prepare and unprepare routines
  drm/exynos: dsi: Add support for panel prepare and unprepare routines
  drm/exynos: dpi: Add support for panel prepare and unprepare routines
  drm/panel: simple: Add dummy prepare and unprepare routines
  drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
  drm/panel: ld9040: Add dummy prepare and unprepare routines
  drm/panel: Provide convenience wrapper for .get_modes()
  drm/panel: add .prepare() and .unprepare() functions
  drm/panel: simple: Remove simple-panel compatible
  ...

13 files changed, 429 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt b/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt
new file mode 100644
index 00000000000..46525ea3e64
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt
@@ -0,0 +1,30 @@
+Device Tree bindings for Armada DRM CRTC driver
+
+Required properties:
+ - compatible: value should be "marvell,dove-lcd".
+ - reg: base address and size of the LCD controller
+ - interrupts: single interrupt number for the LCD controller
+ - port: video output port with endpoints, as described by graph.txt
+
+Optional properties:
+
+ - clocks: as described by clock-bindings.txt
+ - clock-names: as described by clock-bindings.txt
+	"axiclk" - axi bus clock for pixel clock
+	"plldivider" - pll divider clock for pixel clock
+	"ext_ref_clk0" - external clock 0 for pixel clock
+	"ext_ref_clk1" - external clock 1 for pixel clock
+
+Note: all clocks are optional but at least one must be specified.
+Further clocks may be added in the future according to requirements of
+different SoCs.
+
+Example:
+
+	lcd0: lcd-controller@820000 {
+		compatible = "marvell,dove-lcd";
+		reg = <0x820000 0x1000>;
+		interrupts = <47>;
+		clocks = <&si5351 0>;
+		clock-names = "ext_ref_clk_1";
+	};
diff --git a/Documentation/devicetree/bindings/drm/i2c/tda998x.txt b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt
index d7df01c5bb3..e9e4bce4076 100644
--- a/Documentation/devicetree/bindings/drm/i2c/tda998x.txt
+++ b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt
@@ -3,6 +3,8 @@ Device-Tree bindings for the NXP TDA998x HDMI transmitter
 Required properties;
   - compatible: must be "nxp,tda998x"
 
+  - reg: I2C address
+
 Optional properties:
   - interrupts: interrupt number and trigger type
 	default: polling
diff --git a/Documentation/devicetree/bindings/drm/msm/gpu.txt b/Documentation/devicetree/bindings/drm/msm/gpu.txt
new file mode 100644
index 00000000000..67d0a58dbb7
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/msm/gpu.txt
@@ -0,0 +1,52 @@
+Qualcomm adreno/snapdragon GPU
+
+Required properties:
+- compatible: "qcom,adreno-3xx"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt signal from the gpu.
+- clocks: device clocks
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+  * "core_clk"
+  * "iface_clk"
+  * "mem_iface_clk"
+- qcom,chipid: gpu chip-id.  Note this may become optional for future
+  devices if we can reliably read the chipid from hw
+- qcom,gpu-pwrlevels: list of operating points
+  - compatible: "qcom,gpu-pwrlevels"
+  - for each qcom,gpu-pwrlevel:
+    - qcom,gpu-freq: requested gpu clock speed
+    - NOTE: downstream android driver defines additional parameters to
+      configure memory bandwidth scaling per OPP.
+
+Example:
+
+/ {
+	...
+
+	gpu: qcom,kgsl-3d0@4300000 {
+		compatible = "qcom,adreno-3xx";
+		reg = <0x04300000 0x20000>;
+		reg-names = "kgsl_3d0_reg_memory";
+		interrupts = <GIC_SPI 80 0>;
+		interrupt-names = "kgsl_3d0_irq";
+		clock-names =
+		    "core_clk",
+		    "iface_clk",
+		    "mem_iface_clk";
+		clocks =
+		    <&mmcc GFX3D_CLK>,
+		    <&mmcc GFX3D_AHB_CLK>,
+		    <&mmcc MMSS_IMEM_AHB_CLK>;
+		qcom,chipid = <0x03020100>;
+		qcom,gpu-pwrlevels {
+			compatible = "qcom,gpu-pwrlevels";
+			qcom,gpu-pwrlevel@0 {
+				qcom,gpu-freq = <450000000>;
+			};
+			qcom,gpu-pwrlevel@1 {
+				qcom,gpu-freq = <27000000>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/drm/msm/hdmi.txt b/Documentation/devicetree/bindings/drm/msm/hdmi.txt
new file mode 100644
index 00000000000..aca917fe2ba
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/msm/hdmi.txt
@@ -0,0 +1,46 @@
+Qualcomm adreno/snapdragon hdmi output
+
+Required properties:
+- compatible: one of the following
+   * "qcom,hdmi-tx-8660"
+   * "qcom,hdmi-tx-8960"
+- reg: Physical base address and length of the controller's registers
+- reg-names: "core_physical"
+- interrupts: The interrupt signal from the hdmi block.
+- clocks: device clocks
+  See ../clocks/clock-bindings.txt for details.
+- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
+- qcom,hdmi-tx-ddc-data-gpio: ddc data pin
+- qcom,hdmi-tx-hpd-gpio: hpd pin
+- core-vdda-supply: phandle to supply regulator
+- hdmi-mux-supply: phandle to mux regulator
+
+Optional properties:
+- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
+- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin
+
+Example:
+
+/ {
+	...
+
+	hdmi: qcom,hdmi-tx-8960@4a00000 {
+		compatible = "qcom,hdmi-tx-8960";
+		reg-names = "core_physical";
+		reg = <0x04a00000 0x1000>;
+		interrupts = <GIC_SPI 79 0>;
+		clock-names =
+		    "core_clk",
+		    "master_iface_clk",
+		    "slave_iface_clk";
+		clocks =
+		    <&mmcc HDMI_APP_CLK>,
+		    <&mmcc HDMI_M_AHB_CLK>,
+		    <&mmcc HDMI_S_AHB_CLK>;
+		qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>;
+		qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>;
+		qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>;
+		core-vdda-supply = <&pm8921_hdmi_mvs>;
+		hdmi-mux-supply = <&ext_3p3v>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/drm/msm/mdp.txt b/Documentation/devicetree/bindings/drm/msm/mdp.txt
new file mode 100644
index 00000000000..1a0598e5279
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/msm/mdp.txt
@@ -0,0 +1,48 @@
+Qualcomm adreno/snapdragon display controller
+
+Required properties:
+- compatible:
+  * "qcom,mdp" - mdp4
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt signal from the display controller.
+- connectors: array of phandles for output device(s)
+- clocks: device clocks
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+  * "core_clk"
+  * "iface_clk"
+  * "lut_clk"
+  * "src_clk"
+  * "hdmi_clk"
+  * "mpd_clk"
+
+Optional properties:
+- gpus: phandle for gpu device
+
+Example:
+
+/ {
+	...
+
+	mdp: qcom,mdp@5100000 {
+		compatible = "qcom,mdp";
+		reg = <0x05100000 0xf0000>;
+		interrupts = <GIC_SPI 75 0>;
+		connectors = <&hdmi>;
+		gpus = <&gpu>;
+		clock-names =
+		    "core_clk",
+		    "iface_clk",
+		    "lut_clk",
+		    "src_clk",
+		    "hdmi_clk",
+		    "mdp_clk";
+		clocks =
+		    <&mmcc MDP_SRC>,
+		    <&mmcc MDP_AHB_CLK>,
+		    <&mmcc MDP_LUT_CLK>,
+		    <&mmcc TV_SRC>,
+		    <&mmcc HDMI_TV_CLK>,
+		    <&mmcc MDP_TV_CLK>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/gpu/st,stih4xx.txt b/Documentation/devicetree/bindings/gpu/st,stih4xx.txt
new file mode 100644
index 00000000000..2d150c311a0
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpu/st,stih4xx.txt
@@ -0,0 +1,189 @@
+STMicroelectronics stih4xx platforms
+
+- sti-vtg: video timing generator
+  Required properties:
+  - compatible: "st,vtg"
+  - reg: Physical base address of the IP registers and length of memory mapped region.
+  Optional properties:
+  - interrupts : VTG interrupt number to the CPU.
+  - st,slave: phandle on a slave vtg
+
+- sti-vtac: video timing advanced inter dye communication Rx and TX
+  Required properties:
+  - compatible: "st,vtac-main" or "st,vtac-aux"
+  - reg: Physical base address of the IP registers and length of memory mapped region.
+  - clocks: from common clock binding: handle hardware IP needed clocks, the
+    number of clocks may depend of the SoC type.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: names of the clocks listed in clocks property in the same
+    order.
+
+- sti-display-subsystem: Master device for DRM sub-components
+  This device must be the parent of all the sub-components and is responsible
+  of bind them.
+  Required properties:
+  - compatible: "st,sti-display-subsystem"
+  - ranges: to allow probing of subdevices
+
+- sti-compositor: frame compositor engine
+  must be a child of sti-display-subsystem
+  Required properties:
+  - compatible: "st,stih<chip>-compositor"
+  - reg: Physical base address of the IP registers and length of memory mapped region.
+  - clocks: from common clock binding: handle hardware IP needed clocks, the
+    number of clocks may depend of the SoC type.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: names of the clocks listed in clocks property in the same
+    order.
+  - resets: resets to be used by the device
+    See ../reset/reset.txt for details.
+  - reset-names: names of the resets listed in resets property in the same
+    order.
+  - st,vtg: phandle(s) on vtg device (main and aux) nodes.
+
+- sti-tvout: video out hardware block
+  must be a child of sti-display-subsystem
+  Required properties:
+  - compatible: "st,stih<chip>-tvout"
+  - reg: Physical base address of the IP registers and length of memory mapped region.
+  - reg-names: names of the mapped memory regions listed in regs property in
+    the same order.
+  - resets: resets to be used by the device
+    See ../reset/reset.txt for details.
+  - reset-names: names of the resets listed in resets property in the same
+    order.
+  - ranges: to allow probing of subdevices
+
+- sti-hdmi: hdmi output block
+  must be a child of sti-tvout
+  Required properties:
+  - compatible: "st,stih<chip>-hdmi";
+  - reg: Physical base address of the IP registers and length of memory mapped region.
+  - reg-names: names of the mapped memory regions listed in regs property in
+    the same order.
+  - interrupts : HDMI interrupt number to the CPU.
+  - interrupt-names: name of the interrupts listed in interrupts property in
+    the same order
+  - clocks: from common clock binding: handle hardware IP needed clocks, the
+    number of clocks may depend of the SoC type.
+  - clock-names: names of the clocks listed in clocks property in the same
+    order.
+  - hdmi,hpd-gpio: gpio id to detect if an hdmi cable is plugged or not.
+
+sti-hda:
+  Required properties:
+  must be a child of sti-tvout
+  - compatible: "st,stih<chip>-hda"
+  - reg: Physical base address of the IP registers and length of memory mapped region.
+  - reg-names: names of the mapped memory regions listed in regs property in
+    the same order.
+  - clocks: from common clock binding: handle hardware IP needed clocks, the
+    number of clocks may depend of the SoC type.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: names of the clocks listed in clocks property in the same
+    order.
+
+Example:
+
+/ {
+	...
+
+	vtg_main_slave: sti-vtg-main-slave@fe85A800 {
+		compatible	= "st,vtg";
+		reg		= <0xfe85A800 0x300>;
+		interrupts	= <GIC_SPI 175 IRQ_TYPE_NONE>;
+	};
+
+	vtg_main: sti-vtg-main-master@fd348000 {
+		compatible	= "st,vtg";
+		reg		= <0xfd348000 0x400>;
+		st,slave	= <&vtg_main_slave>;
+	};
+
+	vtg_aux_slave: sti-vtg-aux-slave@fd348400 {
+		compatible	= "st,vtg";
+		reg		= <0xfe858200 0x300>;
+		interrupts	= <GIC_SPI 176 IRQ_TYPE_NONE>;
+	};
+
+	vtg_aux: sti-vtg-aux-master@fd348400 {
+		compatible	= "st,vtg";
+		reg		= <0xfd348400 0x400>;
+		st,slave	= <&vtg_aux_slave>;
+	};
+
+
+	sti-vtac-rx-main@fee82800 {
+		compatible	= "st,vtac-main";
+		reg		= <0xfee82800 0x200>;
+		clock-names     = "vtac";
+		clocks          = <&clk_m_a2_div0 CLK_M_VTAC_MAIN_PHY>;
+	};
+
+	sti-vtac-rx-aux@fee82a00 {
+		compatible	= "st,vtac-aux";
+		reg		= <0xfee82a00 0x200>;
+		clock-names     = "vtac";
+		clocks          = <&clk_m_a2_div0 CLK_M_VTAC_AUX_PHY>;
+	};
+
+	sti-vtac-tx-main@fd349000 {
+		compatible	= "st,vtac-main";
+		reg		= <0xfd349000 0x200>, <0xfd320000 0x10000>;
+		clock-names     = "vtac";
+		clocks           = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>;
+	};
+
+	sti-vtac-tx-aux@fd349200 {
+		compatible	= "st,vtac-aux";
+		reg		= <0xfd349200 0x200>, <0xfd320000 0x10000>;
+		clock-names     = "vtac";
+		clocks          = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>;
+	};
+
+	sti-display-subsystem {
+		compatible = "st,sti-display-subsystem";
+		ranges;
+
+		sti-compositor@fd340000 {
+			compatible	= "st,stih416-compositor";
+			reg		= <0xfd340000 0x1000>;
+			clock-names	= "compo_main", "compo_aux",
+			                  "pix_main", "pix_aux";
+			clocks          = <&clk_m_a2_div1 CLK_M_COMPO_MAIN>, <&clk_m_a2_div1 CLK_M_COMPO_AUX>,
+					  <&clockgen_c_vcc CLK_S_PIX_MAIN>, <&clockgen_c_vcc CLK_S_PIX_AUX>;
+			reset-names     = "compo-main", "compo-aux";
+			resets          = <&softreset STIH416_COMPO_M_SOFTRESET>, <&softreset STIH416_COMPO_A_SOFTRESET>;
+			st,vtg		= <&vtg_main>, <&vtg_aux>;
+		};
+
+		sti-tvout@fe000000 {
+			compatible	= "st,stih416-tvout";
+			reg		= <0xfe000000 0x1000>, <0xfe85a000 0x400>, <0xfe830000 0x10000>;
+			reg-names	= "tvout-reg", "hda-reg", "syscfg";
+			reset-names     = "tvout";
+			resets          = <&softreset STIH416_HDTVOUT_SOFTRESET>;
+			ranges;
+
+			sti-hdmi@fe85c000 {
+				compatible	= "st,stih416-hdmi";
+				reg		= <0xfe85c000 0x1000>, <0xfe830000 0x10000>;
+				reg-names	= "hdmi-reg", "syscfg";
+				interrupts	= <GIC_SPI 173 IRQ_TYPE_NONE>;
+				interrupt-names	= "irq";
+				clock-names	= "pix", "tmds", "phy", "audio";
+				clocks          = <&clockgen_c_vcc CLK_S_PIX_HDMI>, <&clockgen_c_vcc CLK_S_TMDS_HDMI>, <&clockgen_c_vcc CLK_S_HDMI_REJECT_PLL>, <&clockgen_b1 CLK_S_PCM_0>;
+				hdmi,hpd-gpio	= <&PIO2 5>;
+			};
+
+			sti-hda@fe85a000 {
+				compatible	= "st,stih416-hda";
+				reg		= <0xfe85a000 0x400>, <0xfe83085c 0x4>;
+				reg-names	= "hda-reg", "video-dacs-ctrl";
+				clock-names	= "pix", "hddac";
+				clocks          = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>;
+			};
+		};
+	};
+	...
+};
diff --git a/Documentation/devicetree/bindings/panel/auo,b133htn01.txt b/Documentation/devicetree/bindings/panel/auo,b133htn01.txt
new file mode 100644
index 00000000000..302226b5bb5
--- /dev/null
+++ b/Documentation/devicetree/bindings/panel/auo,b133htn01.txt
@@ -0,0 +1,7 @@
+AU Optronics Corporation 13.3" FHD (1920x1080) color TFT-LCD panel
+
+Required properties:
+- compatible: should be "auo,b133htn01"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
diff --git a/Documentation/devicetree/bindings/panel/foxlink,fl500wvr00-a0t.txt b/Documentation/devicetree/bindings/panel/foxlink,fl500wvr00-a0t.txt
new file mode 100644
index 00000000000..b47f9d87bc1
--- /dev/null
+++ b/Documentation/devicetree/bindings/panel/foxlink,fl500wvr00-a0t.txt
@@ -0,0 +1,7 @@
+Foxlink Group 5" WVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "foxlink,fl500wvr00-a0t"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
diff --git a/Documentation/devicetree/bindings/panel/innolux,n116bge.txt b/Documentation/devicetree/bindings/panel/innolux,n116bge.txt
new file mode 100644
index 00000000000..081bb939ed3
--- /dev/null
+++ b/Documentation/devicetree/bindings/panel/innolux,n116bge.txt
@@ -0,0 +1,7 @@
+Innolux Corporation 11.6" WXGA (1366x768) TFT LCD panel
+
+Required properties:
+- compatible: should be "innolux,n116bge"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
diff --git a/Documentation/devicetree/bindings/panel/innolux,n156bge-l21.txt b/Documentation/devicetree/bindings/panel/innolux,n156bge-l21.txt
new file mode 100644
index 00000000000..7825844aafd
--- /dev/null
+++ b/Documentation/devicetree/bindings/panel/innolux,n156bge-l21.txt
@@ -0,0 +1,7 @@
+InnoLux 15.6" WXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "innolux,n156bge-l21"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
diff --git a/Documentation/devicetree/bindings/video/exynos_dsim.txt b/Documentation/devicetree/bindings/video/exynos_dsim.txt
index 33b5730d07b..31036c667d5 100644
--- a/Documentation/devicetree/bindings/video/exynos_dsim.txt
+++ b/Documentation/devicetree/bindings/video/exynos_dsim.txt
@@ -1,7 +1,9 @@
 Exynos MIPI DSI Master
 
 Required properties:
-  - compatible: "samsung,exynos4210-mipi-dsi"
+  - compatible: value should be one of the following
+		"samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */
+		"samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */
   - reg: physical base address and length of the registers set for the device
   - interrupts: should contain DSI interrupt
   - clocks: list of clock specifiers, must contain an entry for each required
diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt
index 7bfde9c9d65..08b394b1edb 100644
--- a/Documentation/devicetree/bindings/video/exynos_mixer.txt
+++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt
@@ -4,8 +4,9 @@ Required properties:
 - compatible: value should be one of the following:
 	1) "samsung,exynos5-mixer" <DEPRECATED>
 	2) "samsung,exynos4210-mixer"
-	3) "samsung,exynos5250-mixer"
-	4) "samsung,exynos5420-mixer"
+	3) "samsung,exynos4212-mixer"
+	4) "samsung,exynos5250-mixer"
+	5) "samsung,exynos5420-mixer"
 
 - reg: physical base address of the mixer and length of memory mapped
 	region.
diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt
index 2dad41b689a..8428fcff803 100644
--- a/Documentation/devicetree/bindings/video/samsung-fimd.txt
+++ b/Documentation/devicetree/bindings/video/samsung-fimd.txt
@@ -44,6 +44,34 @@ Optional Properties:
 - display-timings: timing settings for FIMD, as described in document [1].
 		Can be used in case timings cannot be provided otherwise
 		or to override timings provided by the panel.
+- samsung,sysreg: handle to syscon used to control the system registers
+- i80-if-timings: timing configuration for lcd i80 interface support.
+  - cs-setup: clock cycles for the active period of address signal is enabled
+              until chip select is enabled.
+              If not specified, the default value(0) will be used.
+  - wr-setup: clock cycles for the active period of CS signal is enabled until
+              write signal is enabled.
+              If not specified, the default value(0) will be used.
+  - wr-active: clock cycles for the active period of CS is enabled.
+               If not specified, the default value(1) will be used.
+  - wr-hold: clock cycles for the active period of CS is disabled until write
+             signal is disabled.
+             If not specified, the default value(0) will be used.
+
+  The parameters are defined as:
+
+    VCLK(internal)  __|??????|_____|??????|_____|??????|_____|??????|_____|??
+                      :            :            :            :            :
+    Address Output  --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
+                      | cs-setup+1 |            :            :            :
+                      |<---------->|            :            :            :
+    Chip Select     ???????????????|____________:____________:____________|??
+                                   | wr-setup+1 |            | wr-hold+1  |
+                                   |<---------->|            |<---------->|
+    Write Enable    ????????????????????????????|____________|???????????????
+                                                | wr-active+1|
+                                                |<---------->|
+    Video Data      ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
 
 The device node can contain 'port' child nodes according to the bindings defined
 in [2]. The following are properties specific to those nodes: