Merge tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB changes from Greg Kroah-Hartman:
 "Here is the big USB pull request for 3.7-rc1

  There are lots of gadget driver changes (including copying a bunch of
  files into the drivers/staging/ccg/ directory so that the other gadget
  drivers can be fixed up properly without breaking that driver), and we
  remove the old obsolete ub.c driver from the tree.

  There are also the usual XHCI set of updates, and other various driver
  changes and updates.  We also are trying hard to remove the old dbg()
  macro, but the final bits of that removal will be coming in through
  the networking tree before we can delete it for good.

  All of these patches have been in the linux-next tree.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

Fix up several annoying - but fairly mindless - conflicts due to the
termios structure having moved into the tty device, and often clashing
with dbg -> dev_dbg conversion.

* tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (339 commits)
  USB: ezusb: move ezusb.c from drivers/usb/serial to drivers/usb/misc
  USB: uas: fix gcc warning
  USB: uas: fix locking
  USB: Fix race condition when removing host controllers
  USB: uas: add locking
  USB: uas: fix abort
  USB: uas: remove aborted field, replace with status bit.
  USB: uas: fix task management
  USB: uas: keep track of command urbs
  xhci: Intel Panther Point BEI quirk.
  powerpc/usb: remove checking PHY_CLK_VALID for UTMI PHY
  USB: ftdi_sio: add TIAO USB Multi-Protocol Adapter (TUMPA) support
  Revert "usb : Add sysfs files to control port power."
  USB: serial: remove vizzini driver
  usb: host: xhci: Fix Null pointer dereferencing with 71c731a for non-x86 systems
  Increase XHCI suspend timeout to 16ms
  USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
  USB: sierra_ms: don't keep unused variable
  fsl/usb: Add support for USB controller version 2.4
  USB: qcaux: add Pantech vendor class match
  ...

9 files changed, 178 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
new file mode 100644
index 00000000000..ca8fa56e9f0
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -0,0 +1,14 @@
+AM33XX MUSB GLUE
+ - compatible : Should be "ti,musb-am33xx"
+ - ti,hwmods : must be "usb_otg_hs"
+ - multipoint : Should be "1" indicating the musb controller supports
+   multipoint. This is a MUSB configuration-specific setting.
+ - num_eps : Specifies the number of endpoints. This is also a
+   MUSB configuration-specific setting. Should be set to "16"
+ - ram_bits : Specifies the ram address size. Should be set to "12"
+ - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
+   represents PERIPHERAL.
+ - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2"
+   represents PERIPHERAL.
+ - power : Should be "250". This signifies the controller can supply upto
+   500mA when operating in host mode.
diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
index 2c290418bb2..5778b9c83bd 100644
--- a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
+++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
@@ -7,7 +7,10 @@ Required properties:
 
 Optional properties:
 - fsl,usbphy: phandler of usb phy that connects to the only one port
+- fsl,usbmisc: phandler of non-core register device, with one argument
+  that indicate usb controller index
 - vbus-supply: regulator for vbus
+- disable-over-current: disable over current detect
 
 Examples:
 usb@02184000 { /* USB OTG */
@@ -15,4 +18,6 @@ usb@02184000 { /* USB OTG */
 	reg = <0x02184000 0x200>;
 	interrupts = <0 43 0x04>;
 	fsl,usbphy = <&usbphy1>;
+	fsl,usbmisc = <&usbmisc 0>;
+	disable-over-current;
 };
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
new file mode 100644
index 00000000000..29a043ecda5
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -0,0 +1,33 @@
+OMAP GLUE
+
+OMAP MUSB GLUE
+ - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
+ - ti,hwmods : must be "usb_otg_hs"
+ - multipoint : Should be "1" indicating the musb controller supports
+   multipoint. This is a MUSB configuration-specific setting.
+ - num_eps : Specifies the number of endpoints. This is also a
+   MUSB configuration-specific setting. Should be set to "16"
+ - ram_bits : Specifies the ram address size. Should be set to "12"
+ - interface_type : This is a board specific setting to describe the type of
+   interface between the controller and the phy. It should be "0" or "1"
+   specifying ULPI and UTMI respectively.
+ - mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
+   represents PERIPHERAL.
+ - power : Should be "50". This signifies the controller can supply upto
+   100mA when operating in host mode.
+
+SOC specific device node entry
+usb_otg_hs: usb_otg_hs@4a0ab000 {
+	compatible = "ti,omap4-musb";
+	ti,hwmods = "usb_otg_hs";
+	multipoint = <1>;
+	num_eps = <16>;
+	ram_bits = <12>;
+};
+
+Board specific device node entry
+&usb_otg_hs {
+	interface_type = <1>;
+	mode = <3>;
+	power = <50>;
+};
diff --git a/Documentation/devicetree/bindings/usb/platform-uhci.txt b/Documentation/devicetree/bindings/usb/platform-uhci.txt
new file mode 100644
index 00000000000..91477d6830e
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/platform-uhci.txt
@@ -0,0 +1,12 @@
+Generic Platform UHCI controllers.
+
+Required properties:
+ - compatible: Should be "platform-uhci".
+ - reg: Address range of the uhci registers
+ - interrupts: Should contain the uhci interrupt.
+
+usb: uhci@D8007301 {
+	compatible = "platform-uhci", "usb-uhci";
+	reg = <0xD8007301 0x200>;
+	interrupts = <0>;
+};
diff --git a/Documentation/devicetree/bindings/usb/pxa-usb.txt b/Documentation/devicetree/bindings/usb/pxa-usb.txt
new file mode 100644
index 00000000000..79729a948d5
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/pxa-usb.txt
@@ -0,0 +1,31 @@
+PXA USB controllers
+
+OHCI
+
+Required properties:
+ - compatible: Should be "marvell,pxa-ohci" for USB controllers
+   used in host mode.
+
+Optional properties:
+ - "marvell,enable-port1", "marvell,enable-port2", "marvell,enable-port3"
+   If present, enables the appropriate USB port of the controller.
+ - "marvell,port-mode" selects the mode of the ports:
+	1 = PMM_NPS_MODE
+	2 = PMM_GLOBAL_MODE
+	3 = PMM_PERPORT_MODE
+ - "marvell,power-sense-low" - power sense pin is low-active.
+ - "marvell,power-control-low" - power control pin is low-active.
+ - "marvell,no-oc-protection" - disable over-current protection.
+ - "marvell,oc-mode-perport" - enable per-port over-current protection.
+ - "marvell,power_on_delay" Power On to Power Good time - in ms.
+
+Example:
+
+	usb0: ohci@4c000000 {
+		compatible = "marvell,pxa-ohci", "usb-ohci";
+		reg = <0x4c000000 0x100000>;
+		interrupts = <18>;
+		marvell,enable-port1;
+		marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */
+	};
+
diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
new file mode 100644
index 00000000000..36b9aede3f4
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
@@ -0,0 +1,40 @@
+USB COMPARATOR OF TWL CHIPS
+
+TWL6030 USB COMPARATOR
+ - compatible : Should be "ti,twl6030-usb"
+ - interrupts : Two interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts when
+   the controller has to act as host and the second interrupt number is the
+   usb interrupt number that raises VBUS interrupts when the controller has to
+   act as device
+ - usb-supply : phandle to the regulator device tree node. It should be vusb
+   if it is twl6030 or ldousb if it is twl6025 subclass.
+
+twl6030-usb {
+	compatible = "ti,twl6030-usb";
+	interrupts = < 4 10 >;
+};
+
+Board specific device node entry
+&twl6030-usb {
+	usb-supply = <&vusb>;
+};
+
+TWL4030 USB PHY AND COMPARATOR
+ - compatible : Should be "ti,twl4030-usb"
+ - interrupts : The interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts
+   and VBUS interrupts. The second interrupt number is optional.
+ - <supply-name>-supply : phandle to the regulator device tree node.
+   <supply-name> should be vusb1v5, vusb1v8 and vusb3v1
+ - usb_mode : The mode used by the phy to connect to the controller. "1"
+   specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode.
+
+twl4030-usb {
+	compatible = "ti,twl4030-usb";
+	interrupts = < 10 4 >;
+	usb1v5-supply = <&vusb1v5>;
+	usb1v8-supply = <&vusb1v8>;
+	usb3v1-supply = <&vusb3v1>;
+	usb_mode = <1>;
+};
diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
new file mode 100644
index 00000000000..80d4148cb66
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
@@ -0,0 +1,17 @@
+USB PHY
+
+OMAP USB2 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb2"
+ - reg : Address and length of the register set for the device. Also
+add the address of control module dev conf register until a driver for
+control module is added
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb2phy@4a0ad080 {
+	compatible = "ti,omap-usb2";
+	reg = <0x4a0ad080 0x58>,
+	      <0x4a002300 0x4>;
+};
diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt
new file mode 100644
index 00000000000..97ce94e1a6c
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt
@@ -0,0 +1,14 @@
+* Freescale i.MX non-core registers
+
+Required properties:
+- #index-cells: Cells used to descibe usb controller index. Should be <1>
+- compatible: Should be one of below:
+	"fsl,imx6q-usbmisc" for imx6q
+- reg: Should contain registers location and length
+
+Examples:
+usbmisc@02184800 {
+	#index-cells = <1>;
+	compatible = "fsl,imx6q-usbmisc";
+	reg = <0x02184800 0x200>;
+};
diff --git a/Documentation/devicetree/bindings/usb/vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt
new file mode 100644
index 00000000000..5fb8fd6e250
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt
@@ -0,0 +1,12 @@
+VIA VT8500 and Wondermedia WM8xxx SoC USB controllers.
+
+Required properties:
+ - compatible: Should be "via,vt8500-ehci" or "wm,prizm-ehci".
+ - reg: Address range of the ehci registers. size should be 0x200
+ - interrupts: Should contain the ehci interrupt.
+
+usb: ehci@D8007100 {
+	compatible = "wm,prizm-ehci", "usb-ehci";
+	reg = <0xD8007100 0x200>;
+	interrupts = <1>;
+};