Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB patches from Greg KH:
 "Here's the big pull request for the USB driver tree for 3.20-rc1.

  Nothing major happening here, just lots of gadget driver updates, new
  device ids, and a bunch of cleanups.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
  usb: musb: fix device hotplug behind hub
  usb: dwc2: Fix a bug in reading the endpoint directions from reg.
  staging: emxx_udc: fix the build error
  usb: Retry port status check on resume to work around RH bugs
  Revert "usb: Reset USB-3 devices on USB-3 link bounce"
  uhci-hub: use HUB_CHAR_*
  usb: kconfig: replace PPC_OF with PPC
  ehci-pci: disable for Intel MID platforms (update)
  usb: gadget: Kconfig: use bool instead of boolean
  usb: musb: blackfin: remove incorrect __exit_p()
  USB: fix use-after-free bug in usb_hcd_unlink_urb()
  ehci-pci: disable for Intel MID platforms
  usb: host: pci_quirks: joing string literals
  USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
  USB: usbfs: allow URBs to be reaped after disconnection
  cdc-acm: kill unnecessary messages
  cdc-acm: add sanity checks
  usb: phy: phy-generic: Fix USB PHY gpio reset
  usb: dwc2: fix USB core dependencies
  usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
  ...

8 files changed, 74 insertions, 30 deletions

diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
index 46a135dae6b..89caa885d08 100644
--- a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
+++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
@@ -26,6 +26,7 @@ Required properties (port (child) node):
 		  filled in "reg". It can also contain the offset of the system configuration
 		  registers used as glue-logic to setup the device for SATA/PCIe or USB3
 		  devices.
+- st,syscfg	: Offset of the parent configuration register.
 - resets	: phandle to the parent reset controller.
 - reset-names	: Associated name must be "miphy-sw-rst".
 
@@ -54,18 +55,12 @@ example:
 			phy_port0: port@9b22000 {
 				reg = <0x9b22000 0xff>,
 				      <0x9b09000 0xff>,
-				      <0x9b04000 0xff>,
-				      <0x114 0x4>, /* sysctrl MiPHY cntrl */
-				      <0x818 0x4>, /* sysctrl MiPHY status*/
-				      <0xe0  0x4>, /* sysctrl PCIe */
-				      <0xec  0x4>; /* sysctrl SATA */
+				      <0x9b04000 0xff>;
 				reg-names = "sata-up",
 					    "pcie-up",
-					    "pipew",
-					    "miphy-ctrl-glue",
-					    "miphy-status-glue",
-					    "pcie-glue",
-					    "sata-glue";
+					    "pipew";
+
+				st,syscfg = <0x114 0x818 0xe0 0xec>;
 				#phy-cells = <1>;
 				st,osc-rdy;
 				reset-names = "miphy-sw-rst";
@@ -75,18 +70,13 @@ example:
 			phy_port1: port@9b2a000 {
 				reg = <0x9b2a000 0xff>,
 				      <0x9b19000 0xff>,
-				      <0x9b14000 0xff>,
-				      <0x118 0x4>,
-				      <0x81c 0x4>,
-				      <0xe4  0x4>,
-				      <0xf0  0x4>;
+				      <0x9b14000 0xff>;
 				reg-names = "sata-up",
 					    "pcie-up",
-					    "pipew",
-					    "miphy-ctrl-glue",
-					    "miphy-status-glue",
-					    "pcie-glue",
-					    "sata-glue";
+					    "pipew";
+
+				st,syscfg = <0x118 0x81c 0xe4 0xf0>;
+
 				#phy-cells = <1>;
 				st,osc-force-ext;
 				reset-names = "miphy-sw-rst";
@@ -95,13 +85,12 @@ example:
 
 			phy_port2: port@8f95000 {
 				reg = <0x8f95000 0xff>,
-				      <0x8f90000 0xff>,
-				      <0x11c 0x4>,
-				      <0x820 0x4>;
+				      <0x8f90000 0xff>;
 				reg-names = "pipew",
-				    "usb3-up",
-				    "miphy-ctrl-glue",
-				    "miphy-status-glue";
+					    "usb3-up";
+
+				st,syscfg = <0x11c 0x820>;
+
 				#phy-cells = <1>;
 				reset-names = "miphy-sw-rst";
 				resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
@@ -125,4 +114,4 @@ example:
 
 Macro definitions for the supported miphy configuration can be found in:
 
-include/dt-bindings/phy/phy-miphy28lp.h
+include/dt-bindings/phy/phy.h
diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
new file mode 100644
index 00000000000..826454ac43b
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
@@ -0,0 +1,37 @@
+ROCKCHIP USB2 PHY
+
+Required properties:
+ - compatible: rockchip,rk3288-usb-phy
+ - rockchip,grf : phandle to the syscon managing the "general
+   register files"
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+Sub-nodes:
+Each PHY should be represented as a sub-node.
+
+Sub-nodes
+required properties:
+- #phy-cells: should be 0
+- reg: PHY configure reg address offset in GRF
+		"0x320" - for PHY attach to OTG controller
+		"0x334" - for PHY attach to HOST0 controller
+		"0x348" - for PHY attach to HOST1 controller
+
+Optional Properties:
+- clocks : phandle + clock specifier for the phy clocks
+- clock-names: string, clock name, must be "phyclk"
+
+Example:
+
+usbphy: phy {
+	compatible = "rockchip,rk3288-usb-phy";
+	rockchip,grf = <&grf>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usbphy0: usb-phy0 {
+		#phy-cells = <0>;
+		reg = <0x320>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index d5bad920827..91e38cfe1f8 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -3,8 +3,8 @@ Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY
 
 Required properties:
 - compatible : should be "samsung,s5pv210-mipi-video-phy";
-- reg : offset and length of the MIPI DPHY register set;
 - #phy-cells : from the generic phy bindings, must be 1;
+- syscon - phandle to the PMU system controller;
 
 For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in
 the PHY specifier identifies the PHY and its meaning is as follows:
diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt
index bc2222ca3f2..38fee0f66c1 100644
--- a/Documentation/devicetree/bindings/usb/atmel-usb.txt
+++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt
@@ -51,7 +51,10 @@ usb1: gadget@fffa4000 {
 Atmel High-Speed USB device controller
 
 Required properties:
- - compatible: Should be "atmel,at91sam9rl-udc"
+ - compatible: Should be one of the following
+	       "at91sam9rl-udc"
+	       "at91sam9g45-udc"
+	       "sama5d3-udc"
  - reg: Address and length of the register set for the device
  - interrupts: Should contain usba interrupt
  - ep childnode: To specify the number of endpoints and their properties.
diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
index 482f815363e..fd132cbee70 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.txt
+++ b/Documentation/devicetree/bindings/usb/dwc2.txt
@@ -20,6 +20,10 @@ Optional properties:
 Refer to phy/phy-bindings.txt for generic phy consumer properties
 - dr_mode: shall be one of "host", "peripheral" and "otg"
   Refer to usb/generic.txt
+- g-use-dma: enable dma usage in gadget driver.
+- g-rx-fifo-size: size of rx fifo size in gadget mode.
+- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode.
+- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
index b08c903f866..61b045b6d50 100644
--- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
+++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
@@ -14,6 +14,8 @@ Optional properties:
 			 function should be enabled
   - phys: phandle + phy specifier pair
   - phy-names: must be "usb"
+  - dmas: Must contain a list of references to DMA specifiers.
+  - dma-names : Must contain a list of DMA names, "tx" or "rx".
 
 Example:
 	usbhs: usb@e6590000 {
diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt
index 43c1a4e0676..0b04fdff9d5 100644
--- a/Documentation/devicetree/bindings/usb/usb-ehci.txt
+++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt
@@ -12,6 +12,7 @@ Optional properties:
  - big-endian-regs : boolean, set this for hcds with big-endian registers
  - big-endian-desc : boolean, set this for hcds with big-endian descriptors
  - big-endian : boolean, for hcds with big-endian-regs + big-endian-desc
+ - needs-reset-on-resume : boolean, set this to force EHCI reset after resume
  - clocks : a list of phandle + clock specifier pairs
  - phys : phandle + phy specifier pair
  - phy-names : "usb"
diff --git a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
index 1bd37faba05..5be01c859b7 100644
--- a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
+++ b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
@@ -13,10 +13,15 @@ Optional properties:
 - clock-frequency: the clock frequency (in Hz) that the PHY clock must
   be configured to.
 
-- vcc-supply: phandle to the regulator that provides RESET to the PHY.
+- vcc-supply: phandle to the regulator that provides power to the PHY.
 
 - reset-gpios: Should specify the GPIO for reset.
 
+- vbus-detect-gpio: should specify the GPIO detecting a VBus insertion
+                    (see Documentation/devicetree/bindings/gpio/gpio.txt)
+- vbus-regulator : should specifiy the regulator supplying current drawn from
+  the VBus line (see Documentation/devicetree/bindings/regulator/regulator.txt).
+
 Example:
 
 	hsusb1_phy {
@@ -26,8 +31,11 @@ Example:
 		clock-names = "main_clk";
 		vcc-supply = <&hsusb1_vcc_regulator>;
 		reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+		vbus-detect-gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+		vbus-regulator = <&vbus_regulator>;
 	};
 
 hsusb1_phy is a NOP USB PHY device that gets its clock from an oscillator
 and expects that clock to be configured to 19.2MHz by the NOP PHY driver.
 hsusb1_vcc_regulator provides power to the PHY and GPIO 7 controls RESET.
+GPIO 13 detects VBus insertion, and accordingly notifies the vbus-regulator.