Merge branch 'dccp' of git://eden-feed.erg.abdn.ac.uk/dccp_exp

Conflicts:

	net/dccp/input.c
	net/dccp/options.c

1 files changed, 42 insertions, 12 deletions

diff --git a/Documentation/networking/dccp.txt b/Documentation/networking/dccp.txt
index 39131a3c78f..fcfc1253442 100644
--- a/Documentation/networking/dccp.txt
+++ b/Documentation/networking/dccp.txt
@@ -45,6 +45,25 @@ http://linux-net.osdl.org/index.php/DCCP_Testing#Experimental_DCCP_source_tree
 
 Socket options
 ==============
+DCCP_SOCKOPT_QPOLICY_ID sets the dequeuing policy for outgoing packets. It takes
+a policy ID as argument and can only be set before the connection (i.e. changes
+during an established connection are not supported). Currently, two policies are
+defined: the "simple" policy (DCCPQ_POLICY_SIMPLE), which does nothing special,
+and a priority-based variant (DCCPQ_POLICY_PRIO). The latter allows to pass an
+u32 priority value as ancillary data to sendmsg(), where higher numbers indicate
+a higher packet priority (similar to SO_PRIORITY). This ancillary data needs to
+be formatted using a cmsg(3) message header filled in as follows:
+	cmsg->cmsg_level = SOL_DCCP;
+	cmsg->cmsg_type	 = DCCP_SCM_PRIORITY;
+	cmsg->cmsg_len	 = CMSG_LEN(sizeof(uint32_t));	/* or CMSG_LEN(4) */
+
+DCCP_SOCKOPT_QPOLICY_TXQLEN sets the maximum length of the output queue. A zero
+value is always interpreted as unbounded queue length. If different from zero,
+the interpretation of this parameter depends on the current dequeuing policy
+(see above): the "simple" policy will enforce a fixed queue size by returning
+EAGAIN, whereas the "prio" policy enforces a fixed queue length by dropping the
+lowest-priority packet first. The default value for this parameter is
+initialised from /proc/sys/net/dccp/default/tx_qlen.
 
 DCCP_SOCKOPT_SERVICE sets the service. The specification mandates use of
 service codes (RFC 4340, sec. 8.1.2); if this socket option is not set,
@@ -57,6 +76,24 @@ can be set before calling bind().
 DCCP_SOCKOPT_GET_CUR_MPS is read-only and retrieves the current maximum packet
 size (application payload size) in bytes, see RFC 4340, section 14.
 
+DCCP_SOCKOPT_AVAILABLE_CCIDS is also read-only and returns the list of CCIDs
+supported by the endpoint (see include/linux/dccp.h for symbolic constants).
+The caller needs to provide a sufficiently large (> 2) array of type uint8_t.
+
+DCCP_SOCKOPT_CCID is write-only and sets both the TX and RX CCIDs at the same
+time, combining the operation of the next two socket options. This option is
+preferrable over the latter two, since often applications will use the same
+type of CCID for both directions; and mixed use of CCIDs is not currently well
+understood. This socket option takes as argument at least one uint8_t value, or
+an array of uint8_t values, which must match available CCIDS (see above). CCIDs
+must be registered on the socket before calling connect() or listen().
+
+DCCP_SOCKOPT_TX_CCID is read/write. It returns the current CCID (if set) or sets
+the preference list for the TX CCID, using the same format as DCCP_SOCKOPT_CCID.
+Please note that the getsockopt argument type here is `int', not uint8_t.
+
+DCCP_SOCKOPT_RX_CCID is analogous to DCCP_SOCKOPT_TX_CCID, but for the RX CCID.
+
 DCCP_SOCKOPT_SERVER_TIMEWAIT enables the server (listening socket) to hold
 timewait state when closing the connection (RFC 4340, 8.3). The usual case is
 that the closing server sends a CloseReq, whereupon the client holds timewait
@@ -115,23 +152,16 @@ retries2
 	importance for retransmitted acknowledgments and feature negotiation,
 	data packets are never retransmitted. Analogue of tcp_retries2.
 
-send_ndp = 1
-	Whether or not to send NDP count options (sec. 7.7.2).
-
-send_ackvec = 1
-	Whether or not to send Ack Vector options (sec. 11.5).
-
-ack_ratio = 2
-	The default Ack Ratio (sec. 11.3) to use.
-
 tx_ccid = 2
-	Default CCID for the sender-receiver half-connection.
+	Default CCID for the sender-receiver half-connection. Depending on the
+	choice of CCID, the Send Ack Vector feature is enabled automatically.
 
 rx_ccid = 2
-	Default CCID for the receiver-sender half-connection.
+	Default CCID for the receiver-sender half-connection; see tx_ccid.
 
 seq_window = 100
-	The initial sequence window (sec. 7.5.2).
+	The initial sequence window (sec. 7.5.2) of the sender. This influences
+	the local ackno validity and the remote seqno validity windows (7.5.1).
 
 tx_qlen = 5
 	The size of the transmit buffer in packets. A value of 0 corresponds