davinci: Add support for DA850/OMAP-L138 EVM board

Add support for the DA850/OMAP-L138 Evaluation Module (EVM)
from TI.  The EVM has User Interface (UI) card which contains
various devices. This UI card can be connected to the base
board. Support for all the devices on the UI card and ones on
the EVM will be added in subsequent patches.

The EVM schematics are not available publicly yet; but should
be available soon.

A new defconfig for this board has been added mainly because
the DA830/OMAP-L137 defconfig forces writethrough cache mode
which is not required on DA850/OMAP-L138.

This patch has been boot tested on DA850/OMAP-L138 EVM
using ramdisk as filesystem.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

1 files changed, 102 insertions, 0 deletions

diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
new file mode 100644
index 00000000000..eaa1fc1bc5f
--- /dev/null
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -0,0 +1,102 @@
+/*
+ * TI DA850/OMAP-L138 EVM board
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Derived from: arch/arm/mach-davinci/board-da830-evm.c
+ * Original Copyrights follow:
+ *
+ * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/common.h>
+#include <mach/irqs.h>
+#include <mach/cp_intc.h>
+#include <mach/da8xx.h>
+
+static struct davinci_i2c_platform_data da850_evm_i2c_0_pdata = {
+	.bus_freq	= 100,	/* kHz */
+	.bus_delay	= 0,	/* usec */
+};
+
+static struct davinci_uart_config da850_evm_uart_config __initdata = {
+	.enabled_uarts = 0x7,
+};
+
+static __init void da850_evm_init(void)
+{
+	int ret;
+
+	ret = da8xx_register_edma();
+	if (ret)
+		pr_warning("da850_evm_init: edma registration failed: %d\n",
+				ret);
+
+	ret = da8xx_pinmux_setup(da850_i2c0_pins);
+	if (ret)
+		pr_warning("da850_evm_init: i2c0 mux setup failed: %d\n",
+				ret);
+
+	ret = da8xx_register_i2c(0, &da850_evm_i2c_0_pdata);
+	if (ret)
+		pr_warning("da850_evm_init: i2c0 registration failed: %d\n",
+				ret);
+
+	ret = da8xx_register_watchdog();
+	if (ret)
+		pr_warning("da830_evm_init: watchdog registration failed: %d\n",
+				ret);
+
+	davinci_serial_init(&da850_evm_uart_config);
+
+	/*
+	 * shut down uart 0 and 1; they are not used on the board and
+	 * accessing them causes endless "too much work in irq53" messages
+	 * with arago fs
+	 */
+	__raw_writel(0, IO_ADDRESS(DA8XX_UART1_BASE) + 0x30);
+	__raw_writel(0, IO_ADDRESS(DA8XX_UART0_BASE) + 0x30);
+}
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init da850_evm_console_init(void)
+{
+	return add_preferred_console("ttyS", 2, "115200");
+}
+console_initcall(da850_evm_console_init);
+#endif
+
+static __init void da850_evm_irq_init(void)
+{
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+	cp_intc_init((void __iomem *)DA8XX_CP_INTC_VIRT, DA850_N_CP_INTC_IRQ,
+			soc_info->intc_irq_prios);
+}
+
+static void __init da850_evm_map_io(void)
+{
+	da850_init();
+}
+
+MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138 EVM")
+	.phys_io	= IO_PHYS,
+	.io_pg_offst	= (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
+	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.map_io		= da850_evm_map_io,
+	.init_irq	= da850_evm_irq_init,
+	.timer		= &davinci_timer,
+	.init_machine	= da850_evm_init,
+MACHINE_END