Merge branch 'master' of /home/davem/src/GIT/linux-2.6/

54 files changed, 2506 insertions, 609 deletions

diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index dee92182749..38fbd0a0e40 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -115,6 +115,11 @@ config MACH_CM_X300
 	select CPU_PXA310
 	select HAVE_PWM
 
+config MACH_CAPC7117
+	bool "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM"
+	select CPU_PXA320
+	select PXA3xx
+
 config ARCH_GUMSTIX
 	bool "Gumstix XScale 255 boards"
 	select PXA25x
@@ -417,6 +422,24 @@ config MACH_TREO680
 	  Say Y here if you intend to run this kernel on Palm Treo 680
 	  smartphone.
 
+config MACH_RAUMFELD_RC
+	bool "Raumfeld Controller"
+	select PXA3xx
+	select CPU_PXA300
+	select HAVE_PWM
+
+config MACH_RAUMFELD_CONNECTOR
+	bool "Raumfeld Connector"
+	select PXA3xx
+	select CPU_PXA300
+	select PXA_SSP
+
+config MACH_RAUMFELD_SPEAKER
+	bool "Raumfeld Speaker"
+	select PXA3xx
+	select CPU_PXA300
+	select PXA_SSP
+
 config PXA_SHARPSL
 	bool "SHARP Zaurus SL-5600, SL-C7xx and SL-Cxx00 Models"
 	select SHARP_SCOOP
@@ -435,6 +458,7 @@ config SHARPSL_PM
 config CORGI_SSP_DEPRECATED
 	bool
 	select PXA_SSP
+	select PXA_SSP_LEGACY
 	help
 	  This option will include corgi_ssp.c and corgi_lcd.c
 	  that corgi_ts.c and other legacy drivers (corgi_bl.c
@@ -446,6 +470,7 @@ config MACH_POODLE
 	select PXA25x
 	select SHARP_LOCOMO
 	select PXA_SSP
+	select PXA_HAVE_BOARD_IRQS
 
 config MACH_CORGI
 	bool "Enable Sharp SL-C700 (Corgi) Support"
@@ -492,6 +517,11 @@ config MACH_TOSA
 	select PXA25x
 	select PXA_HAVE_BOARD_IRQS
 
+config MACH_ICONTROL
+	bool "TMT iControl/SafeTCam based on the MXM-8x10 CoM"
+	select CPU_PXA320
+	select PXA3xx
+
 config ARCH_PXA_ESERIES
 	bool "PXA based Toshiba e-series PDAs"
 	select PXA25x
@@ -629,6 +659,11 @@ config PXA_SSP
 	help
 	  Enable support for PXA2xx SSP ports
 
+config PXA_SSP_LEGACY
+	bool
+	help
+	  Support of legacy SSP API
+
 config TOSA_BT
 	tristate "Control the state of built-in bluetooth chip on Sharp SL-6000"
 	depends on MACH_TOSA
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index f64afda7e6f..86bc87b7f2d 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_MACH_ARMCORE)	+= cm-x2xx-pci.o
 endif
 obj-$(CONFIG_MACH_EM_X270)	+= em-x270.o
 obj-$(CONFIG_MACH_CM_X300)      += cm-x300.o
+obj-$(CONFIG_MACH_CAPC7117)     += capc7117.o mxm8x10.o
 obj-$(CONFIG_ARCH_GUMSTIX)	+= gumstix.o
 obj-$(CONFIG_GUMSTIX_AM200EPD)	+= am200epd.o
 obj-$(CONFIG_GUMSTIX_AM300EPD)	+= am300epd.o
@@ -82,6 +83,7 @@ obj-$(CONFIG_PXA_SHARP_Cxx00)	+= spitz.o sharpsl_pm.o spitz_pm.o
 obj-$(CONFIG_CORGI_SSP_DEPRECATED)	+= corgi_ssp.o corgi_lcd.o
 obj-$(CONFIG_MACH_POODLE)	+= poodle.o
 obj-$(CONFIG_MACH_TOSA)		+= tosa.o
+obj-$(CONFIG_MACH_ICONTROL)     += icontrol.o mxm8x10.o
 obj-$(CONFIG_ARCH_PXA_ESERIES)	+= eseries.o
 obj-$(CONFIG_MACH_E330)		+= e330.o
 obj-$(CONFIG_MACH_E350)		+= e350.o
@@ -89,6 +91,9 @@ obj-$(CONFIG_MACH_E740)		+= e740.o
 obj-$(CONFIG_MACH_E750)		+= e750.o
 obj-$(CONFIG_MACH_E400)		+= e400.o
 obj-$(CONFIG_MACH_E800)		+= e800.o
+obj-$(CONFIG_MACH_RAUMFELD_RC)		+= raumfeld.o
+obj-$(CONFIG_MACH_RAUMFELD_CONNECTOR)	+= raumfeld.o
+obj-$(CONFIG_MACH_RAUMFELD_SPEAKER)	+= raumfeld.o
 
 # Support for blinky lights
 led-y := leds.o
diff --git a/arch/arm/mach-pxa/am300epd.c b/arch/arm/mach-pxa/am300epd.c
index 4bd10a17332..993d75e6639 100644
--- a/arch/arm/mach-pxa/am300epd.c
+++ b/arch/arm/mach-pxa/am300epd.c
@@ -288,7 +288,7 @@ int __init am300_init(void)
 }
 
 module_param(panel_type, uint, 0);
-MODULE_PARM_DESC(panel_type, "Select the panel type: 6, 8, 97");
+MODULE_PARM_DESC(panel_type, "Select the panel type: 37, 6, 97");
 
 MODULE_DESCRIPTION("board driver for am300 epd kit");
 MODULE_AUTHOR("Jaya Kumar");
diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c
index b8cd07ca938..f3b5ace815e 100644
--- a/arch/arm/mach-pxa/balloon3.c
+++ b/arch/arm/mach-pxa/balloon3.c
@@ -132,6 +132,14 @@ static void __init balloon3_init_irq(void)
 		"enabled\n", __func__, BALLOON3_AUX_NIRQ);
 }
 
+static unsigned long balloon3_ac97_pin_config[] = {
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+	GPIO113_AC97_nRESET,
+};
+
 static void balloon3_backlight_power(int on)
 {
 	pr_debug("%s: power is %s\n", __func__, on ? "on" : "off");
@@ -140,26 +148,7 @@ static void balloon3_backlight_power(int on)
 
 static unsigned long balloon3_lcd_pin_config[] = {
 	/* LCD - 16bpp Active TFT */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	GPIO99_GPIO,		/* Backlight */
 };
@@ -311,8 +300,10 @@ static void __init balloon3_init(void)
 	pxa_set_stuart_info(NULL);
 
 	pxa_set_i2c_info(NULL);
-	if (balloon3_has(BALLOON3_FEATURE_AUDIO))
+	if (balloon3_has(BALLOON3_FEATURE_AUDIO)) {
+		pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_ac97_pin_config));
 		pxa_set_ac97_info(NULL);
+	}
 
 	if (balloon3_has(BALLOON3_FEATURE_TOPPOLY)) {
 		pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_lcd_pin_config));
diff --git a/arch/arm/mach-pxa/capc7117.c b/arch/arm/mach-pxa/capc7117.c
new file mode 100644
index 00000000000..aae544631a8
--- /dev/null
+++ b/arch/arm/mach-pxa/capc7117.c
@@ -0,0 +1,158 @@
+/*
+ * linux/arch/arm/mach-pxa/capc7117.c
+ *
+ * Support for the Embedian CAPC-7117 Evaluation Kit
+ * based on the Embedian MXM-8x10 Computer on Module
+ *
+ * Copyright (C) 2009 Embedian Inc.
+ * Copyright (C) 2009 TMT Services & Supplies (Pty) Ltd.
+ *
+ * 2007-09-04: eric miao <eric.y.miao@gmail.com>
+ *             rewrite to align with latest kernel
+ *
+ * 2010-01-09: Edwin Peer <epeer@tmtservices.co.za>
+ *             Hennie van der Merwe <hvdmerwe@tmtservices.co.za>
+ *             rework for upstream merge
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/serial_8250.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/pxa320.h>
+#include <mach/mxm8x10.h>
+
+#include "generic.h"
+
+/* IDE (PATA) Support */
+static struct pata_platform_info pata_platform_data = {
+	.ioport_shift = 1
+};
+
+static struct resource capc7117_ide_resources[] = {
+	[0] = {
+	       .start = 0x11000020,
+	       .end = 0x1100003f,
+	       .flags = IORESOURCE_MEM
+	},
+	[1] = {
+	       .start = 0x1100001c,
+	       .end = 0x1100001c,
+	       .flags = IORESOURCE_MEM
+	},
+	[2] = {
+	       .start = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO76)),
+	       .end = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO76)),
+	       .flags = IORESOURCE_IRQ | IRQF_TRIGGER_RISING
+	}
+};
+
+static struct platform_device capc7117_ide_device = {
+	.name = "pata_platform",
+	.num_resources = ARRAY_SIZE(capc7117_ide_resources),
+	.resource = capc7117_ide_resources,
+	.dev = {
+		.platform_data = &pata_platform_data,
+		.coherent_dma_mask = ~0		/* grumble */
+	}
+};
+
+static void __init capc7117_ide_init(void)
+{
+	platform_device_register(&capc7117_ide_device);
+}
+
+/* TI16C752 UART support */
+#define	TI16C752_FLAGS		(UPF_BOOT_AUTOCONF | \
+					UPF_IOREMAP | \
+					UPF_BUGGY_UART | \
+					UPF_SKIP_TEST)
+#define	TI16C752_UARTCLK	(22118400)
+static struct plat_serial8250_port ti16c752_platform_data[] = {
+	[0] = {
+	       .mapbase = 0x14000000,
+	       .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO78)),
+	       .irqflags = IRQF_TRIGGER_RISING,
+	       .flags = TI16C752_FLAGS,
+	       .iotype = UPIO_MEM,
+	       .regshift = 1,
+	       .uartclk = TI16C752_UARTCLK
+	},
+	[1] = {
+	       .mapbase = 0x14000040,
+	       .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO79)),
+	       .irqflags = IRQF_TRIGGER_RISING,
+	       .flags = TI16C752_FLAGS,
+	       .iotype = UPIO_MEM,
+	       .regshift = 1,
+	       .uartclk = TI16C752_UARTCLK
+	},
+	[2] = {
+	       .mapbase = 0x14000080,
+	       .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO80)),
+	       .irqflags = IRQF_TRIGGER_RISING,
+	       .flags = TI16C752_FLAGS,
+	       .iotype = UPIO_MEM,
+	       .regshift = 1,
+	       .uartclk = TI16C752_UARTCLK
+	},
+	[3] = {
+	       .mapbase = 0x140000c0,
+	       .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO81)),
+	       .irqflags = IRQF_TRIGGER_RISING,
+	       .flags = TI16C752_FLAGS,
+	       .iotype = UPIO_MEM,
+	       .regshift = 1,
+	       .uartclk = TI16C752_UARTCLK
+	},
+	[4] = {
+	       /* end of array */
+	}
+};
+
+static struct platform_device ti16c752_device = {
+	.name = "serial8250",
+	.id = PLAT8250_DEV_PLATFORM,
+	.dev = {
+		.platform_data = ti16c752_platform_data
+	}
+};
+
+static void __init capc7117_uarts_init(void)
+{
+	platform_device_register(&ti16c752_device);
+}
+
+static void __init capc7117_init(void)
+{
+	/* Init CoM */
+	mxm_8x10_barebones_init();
+
+	/* Init evaluation board peripherals */
+	mxm_8x10_ac97_init();
+	mxm_8x10_usb_host_init();
+	mxm_8x10_mmc_init();
+
+	capc7117_uarts_init();
+	capc7117_ide_init();
+}
+
+MACHINE_START(CAPC7117,
+	      "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM")
+	.phys_io = 0x40000000,
+	.boot_params = 0xa0000100,
+	.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.map_io = pxa_map_io,
+	.init_irq = pxa3xx_init_irq,
+	.timer = &pxa_timer,
+	.init_machine = capc7117_init
+MACHINE_END
diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c
index 253fd76142d..f1a7703d771 100644
--- a/arch/arm/mach-pxa/cm-x255.c
+++ b/arch/arm/mach-pxa/cm-x255.c
@@ -50,26 +50,7 @@ static unsigned long cmx255_pin_config[] = {
 	GPIO47_STUART_TXD,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* SSP1 */
 	GPIO23_SSP1_SCLK,
diff --git a/arch/arm/mach-pxa/cm-x270.c b/arch/arm/mach-pxa/cm-x270.c
index eea78b6c2bc..a9926bb7592 100644
--- a/arch/arm/mach-pxa/cm-x270.c
+++ b/arch/arm/mach-pxa/cm-x270.c
@@ -71,26 +71,7 @@ static unsigned long cmx270_pin_config[] = {
 	GPIO111_MMC_DAT_3,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* I2C */
 	GPIO117_I2C_SCL,
@@ -195,33 +176,57 @@ static struct resource cmx270_2700G_resource[] = {
 	},
 };
 
-static unsigned long save_lcd_regs[10];
+static unsigned long cmx270_marathon_on[] = {
+	GPIO58_GPIO,
+	GPIO59_GPIO,
+	GPIO60_GPIO,
+	GPIO61_GPIO,
+	GPIO62_GPIO,
+	GPIO63_GPIO,
+	GPIO64_GPIO,
+	GPIO65_GPIO,
+	GPIO66_GPIO,
+	GPIO67_GPIO,
+	GPIO68_GPIO,
+	GPIO69_GPIO,
+	GPIO70_GPIO,
+	GPIO71_GPIO,
+	GPIO72_GPIO,
+	GPIO73_GPIO,
+	GPIO74_GPIO,
+	GPIO75_GPIO,
+	GPIO76_GPIO,
+	GPIO77_GPIO,
+};
+
+static unsigned long cmx270_marathon_off[] = {
+	GPIOxx_LCD_TFT_16BPP,
+};
 
 static int cmx270_marathon_probe(struct fb_info *fb)
 {
-	/* save PXA-270 pin settings before enabling 2700G */
-	save_lcd_regs[0] = GPDR1;
-	save_lcd_regs[1] = GPDR2;
-	save_lcd_regs[2] = GAFR1_U;
-	save_lcd_regs[3] = GAFR2_L;
-	save_lcd_regs[4] = GAFR2_U;
-
-	/* Disable PXA-270 on-chip controller driving pins */
-	GPDR1 &= ~(0xfc000000);
-	GPDR2 &= ~(0x00c03fff);
-	GAFR1_U &= ~(0xfff00000);
-	GAFR2_L &= ~(0x0fffffff);
-	GAFR2_U &= ~(0x0000f000);
+	int gpio, err;
+
+	for (gpio = 58; gpio <= 77; gpio++) {
+		err = gpio_request(gpio, "LCD");
+		if (err)
+			return err;
+		gpio_direction_input(gpio);
+	}
+
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_marathon_on));
 	return 0;
 }
 
 static int cmx270_marathon_remove(struct fb_info *fb)
 {
-	GPDR1 =   save_lcd_regs[0];
-	GPDR2 =   save_lcd_regs[1];
-	GAFR1_U = save_lcd_regs[2];
-	GAFR2_L = save_lcd_regs[3];
-	GAFR2_U = save_lcd_regs[4];
+	int gpio;
+
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_marathon_off));
+
+	for (gpio = 58; gpio <= 77; gpio++)
+		gpio_free(gpio);
+
 	return 0;
 }
 
diff --git a/arch/arm/mach-pxa/cm-x2xx-pci.c b/arch/arm/mach-pxa/cm-x2xx-pci.c
index 7873fa3d8fa..161fc2d6120 100644
--- a/arch/arm/mach-pxa/cm-x2xx-pci.c
+++ b/arch/arm/mach-pxa/cm-x2xx-pci.c
@@ -59,7 +59,7 @@ void __init cmx2xx_pci_adjust_zones(int node, unsigned long *zone_size,
 static void cmx2xx_it8152_irq_demux(unsigned int irq, struct irq_desc *desc)
 {
 	/* clear our parent irq */
-	GEDR(cmx2xx_it8152_irq_gpio) = GPIO_bit(cmx2xx_it8152_irq_gpio);
+	desc->chip->ack(irq);
 
 	it8152_irq_demux(irq, desc);
 }
diff --git a/arch/arm/mach-pxa/corgi_ssp.c b/arch/arm/mach-pxa/corgi_ssp.c
index a5ee70735e0..1d9bc118ee3 100644
--- a/arch/arm/mach-pxa/corgi_ssp.c
+++ b/arch/arm/mach-pxa/corgi_ssp.c
@@ -204,7 +204,7 @@ void __init corgi_ssp_set_machinfo(struct corgissp_machinfo *machinfo)
 	ssp_machinfo = machinfo;
 }
 
-static int __init corgi_ssp_probe(struct platform_device *dev)
+static int __devinit corgi_ssp_probe(struct platform_device *dev)
 {
 	int ret;
 
diff --git a/arch/arm/mach-pxa/e740.c b/arch/arm/mach-pxa/e740.c
index 94b23a9e387..d578021d1a1 100644
--- a/arch/arm/mach-pxa/e740.c
+++ b/arch/arm/mach-pxa/e740.c
@@ -134,6 +134,12 @@ static unsigned long e740_pin_config[] __initdata = {
 	/* IrDA */
 	GPIO38_GPIO | MFP_LPM_DRIVE_HIGH,
 
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+
 	/* Audio power control */
 	GPIO16_GPIO,  /* AC97 codec AVDD2 supply (analogue power) */
 	GPIO40_GPIO,  /* Mic amp power */
diff --git a/arch/arm/mach-pxa/e750.c b/arch/arm/mach-pxa/e750.c
index 5eccbce73a3..af83caa52dd 100644
--- a/arch/arm/mach-pxa/e750.c
+++ b/arch/arm/mach-pxa/e750.c
@@ -132,6 +132,12 @@ static unsigned long e750_pin_config[] __initdata = {
 	/* IrDA */
 	GPIO38_GPIO | MFP_LPM_DRIVE_HIGH,
 
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+
 	/* Audio power control */
 	GPIO4_GPIO,  /* Headphone amp power */
 	GPIO7_GPIO,  /* Speaker amp power */
diff --git a/arch/arm/mach-pxa/e800.c b/arch/arm/mach-pxa/e800.c
index aad129bed19..8ea97bf53fe 100644
--- a/arch/arm/mach-pxa/e800.c
+++ b/arch/arm/mach-pxa/e800.c
@@ -35,6 +35,14 @@
 
 /* ------------------------ e800 LCD definitions ------------------------- */
 
+static unsigned long e800_pin_config[] __initdata = {
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+};
+
 static struct w100_gen_regs e800_lcd_regs = {
 	.lcd_format =            0x00008003,
 	.lcdd_cntl1 =            0x02a00000,
@@ -195,6 +203,7 @@ static struct platform_device *devices[] __initdata = {
 
 static void __init e800_init(void)
 {
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(e800_pin_config));
 	pxa_set_ffuart_info(NULL);
 	pxa_set_btuart_info(NULL);
 	pxa_set_stuart_info(NULL);
diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
index c8a01bc85fd..aab04f33e49 100644
--- a/arch/arm/mach-pxa/em-x270.c
+++ b/arch/arm/mach-pxa/em-x270.c
@@ -109,26 +109,7 @@ static unsigned long common_pin_config[] = {
 	GPIO111_MMC_DAT_3,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* QCI */
 	GPIO84_CIF_FV,
diff --git a/arch/arm/mach-pxa/icontrol.c b/arch/arm/mach-pxa/icontrol.c
new file mode 100644
index 00000000000..771137fc1a8
--- /dev/null
+++ b/arch/arm/mach-pxa/icontrol.c
@@ -0,0 +1,202 @@
+/*
+ * linux/arch/arm/mach-pxa/icontrol.c
+ *
+ * Support for the iControl and SafeTcam platforms from TMT Services
+ * using the Embedian MXM-8x10 Computer on Module
+ *
+ * Copyright (C) 2009 TMT Services & Supplies (Pty) Ltd.
+ *
+ * 2010-01-21 Hennie van der Merve <hvdmerwe@tmtservies.co.za>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/pxa320.h>
+#include <mach/mxm8x10.h>
+
+#include <linux/spi/spi.h>
+#include <mach/pxa2xx_spi.h>
+#include <linux/can/platform/mcp251x.h>
+
+#include "generic.h"
+
+#define ICONTROL_MCP251x_nCS1	(15)
+#define ICONTROL_MCP251x_nCS2	(16)
+#define ICONTROL_MCP251x_nCS3	(17)
+#define ICONTROL_MCP251x_nCS4	(24)
+
+#define ICONTROL_MCP251x_nIRQ1	(74)
+#define ICONTROL_MCP251x_nIRQ2	(75)
+#define ICONTROL_MCP251x_nIRQ3	(76)
+#define ICONTROL_MCP251x_nIRQ4	(77)
+
+static struct pxa2xx_spi_chip mcp251x_chip_info1 = {
+	.tx_threshold   = 8,
+	.rx_threshold   = 128,
+	.dma_burst_size = 8,
+	.timeout        = 235,
+	.gpio_cs        = ICONTROL_MCP251x_nCS1
+};
+
+static struct pxa2xx_spi_chip mcp251x_chip_info2 = {
+	.tx_threshold   = 8,
+	.rx_threshold   = 128,
+	.dma_burst_size = 8,
+	.timeout        = 235,
+	.gpio_cs        = ICONTROL_MCP251x_nCS2
+};
+
+static struct pxa2xx_spi_chip mcp251x_chip_info3 = {
+	.tx_threshold   = 8,
+	.rx_threshold   = 128,
+	.dma_burst_size = 8,
+	.timeout        = 235,
+	.gpio_cs        = ICONTROL_MCP251x_nCS3
+};
+
+static struct pxa2xx_spi_chip mcp251x_chip_info4 = {
+	.tx_threshold   = 8,
+	.rx_threshold   = 128,
+	.dma_burst_size = 8,
+	.timeout        = 235,
+	.gpio_cs        = ICONTROL_MCP251x_nCS4
+};
+
+static struct mcp251x_platform_data mcp251x_info = {
+	.oscillator_frequency = 16E6,
+	.model                = CAN_MCP251X_MCP2515,
+	.board_specific_setup = NULL,
+	.power_enable         = NULL,
+	.transceiver_enable   = NULL
+};
+
+static struct spi_board_info mcp251x_board_info[] = {
+	{
+		.modalias        = "mcp251x",
+		.max_speed_hz    = 6500000,
+		.bus_num         = 3,
+		.chip_select     = 0,
+		.platform_data   = &mcp251x_info,
+		.controller_data = &mcp251x_chip_info1,
+		.irq             = gpio_to_irq(ICONTROL_MCP251x_nIRQ1)
+	},
+	{
+		.modalias        = "mcp251x",
+		.max_speed_hz    = 6500000,
+		.bus_num         = 3,
+		.chip_select     = 1,
+		.platform_data   = &mcp251x_info,
+		.controller_data = &mcp251x_chip_info2,
+		.irq             = gpio_to_irq(ICONTROL_MCP251x_nIRQ2)
+	},
+	{
+		.modalias        = "mcp251x",
+		.max_speed_hz    = 6500000,
+		.bus_num         = 4,
+		.chip_select     = 0,
+		.platform_data   = &mcp251x_info,
+		.controller_data = &mcp251x_chip_info3,
+		.irq             = gpio_to_irq(ICONTROL_MCP251x_nIRQ3)
+	},
+	{
+		.modalias        = "mcp251x",
+		.max_speed_hz    = 6500000,
+		.bus_num         = 4,
+		.chip_select     = 1,
+		.platform_data   = &mcp251x_info,
+		.controller_data = &mcp251x_chip_info4,
+		.irq             = gpio_to_irq(ICONTROL_MCP251x_nIRQ4)
+	}
+};
+
+static struct pxa2xx_spi_master pxa_ssp3_spi_master_info = {
+	.clock_enable   = CKEN_SSP3,
+	.num_chipselect = 2,
+	.enable_dma     = 1
+};
+
+static struct pxa2xx_spi_master pxa_ssp4_spi_master_info = {
+	.clock_enable   = CKEN_SSP4,
+	.num_chipselect = 2,
+	.enable_dma     = 1
+};
+
+struct platform_device pxa_spi_ssp3 = {
+	.name          = "pxa2xx-spi",
+	.id            = 3,
+	.dev           = {
+		.platform_data = &pxa_ssp3_spi_master_info,
+	}
+};
+
+struct platform_device pxa_spi_ssp4 = {
+	.name          = "pxa2xx-spi",
+	.id            = 4,
+	.dev           = {
+		.platform_data = &pxa_ssp4_spi_master_info,
+	}
+};
+
+static struct platform_device *icontrol_spi_devices[] __initdata = {
+	&pxa_spi_ssp3,
+	&pxa_spi_ssp4,
+};
+
+static mfp_cfg_t mfp_can_cfg[] __initdata = {
+	/* CAN CS lines */
+	GPIO15_GPIO,
+	GPIO16_GPIO,
+	GPIO17_GPIO,
+	GPIO24_GPIO,
+
+	/* SPI (SSP3) lines */
+	GPIO89_SSP3_SCLK,
+	GPIO91_SSP3_TXD,
+	GPIO92_SSP3_RXD,
+
+	/* SPI (SSP4) lines */
+	GPIO93_SSP4_SCLK,
+	GPIO95_SSP4_TXD,
+	GPIO96_SSP4_RXD,
+
+	/* CAN nIRQ lines */
+	GPIO74_GPIO | MFP_LPM_EDGE_RISE,
+	GPIO75_GPIO | MFP_LPM_EDGE_RISE,
+	GPIO76_GPIO | MFP_LPM_EDGE_RISE,
+	GPIO77_GPIO | MFP_LPM_EDGE_RISE
+};
+
+static void __init icontrol_can_init(void)
+{
+	pxa3xx_mfp_config(ARRAY_AND_SIZE(mfp_can_cfg));
+	platform_add_devices(ARRAY_AND_SIZE(icontrol_spi_devices));
+	spi_register_board_info(ARRAY_AND_SIZE(mcp251x_board_info));
+}
+
+static void __init icontrol_init(void)
+{
+	mxm_8x10_barebones_init();
+	mxm_8x10_usb_host_init();
+	mxm_8x10_mmc_init();
+
+	icontrol_can_init();
+}
+
+MACHINE_START(ICONTROL, "iControl/SafeTcam boards using Embedian MXM-8x10 CoM")
+	.phys_io	= 0x40000000,
+	.boot_params	= 0xa0000100,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.map_io		= pxa_map_io,
+	.init_irq	= pxa3xx_init_irq,
+	.timer		= &pxa_timer,
+	.init_machine	= icontrol_init
+MACHINE_END
diff --git a/arch/arm/mach-pxa/idp.c b/arch/arm/mach-pxa/idp.c
index 5c9e11d74f4..bc78c4dc0c6 100644
--- a/arch/arm/mach-pxa/idp.c
+++ b/arch/arm/mach-pxa/idp.c
@@ -47,25 +47,7 @@
 
 static unsigned long idp_pin_config[] __initdata = {
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
+	GPIOxx_LCD_DSTN_16BPP,
 
 	/* BTUART */
 	GPIO42_BTUART_RXD,
diff --git a/arch/arm/mach-pxa/imote2.c b/arch/arm/mach-pxa/imote2.c
index 5b0862df61a..b2f878bd460 100644
--- a/arch/arm/mach-pxa/imote2.c
+++ b/arch/arm/mach-pxa/imote2.c
@@ -64,7 +64,6 @@ static unsigned long imote2_pin_config[] __initdata = {
 	GPIO116_GPIO,			/* CC_CCA */
 	GPIO0_GPIO,			/* CC_FIFOP */
 	GPIO16_GPIO,			/* CCSFD */
-	GPIO39_GPIO,			/* CSn */
 	GPIO115_GPIO,			/* Power enable */
 
 	/* I2C */
@@ -72,7 +71,7 @@ static unsigned long imote2_pin_config[] __initdata = {
 	GPIO118_I2C_SDA,
 
 	/* SSP 3 - 802.15.4 radio */
-	GPIO39_GPIO, 			/* Chip Select */
+	GPIO39_GPIO,			/* Chip Select */
 	GPIO34_SSP3_SCLK,
 	GPIO35_SSP3_TXD,
 	GPIO41_SSP3_RXD,
diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/include/mach/balloon3.h
index bfec09b1814..1a741065045 100644
--- a/arch/arm/mach-pxa/include/mach/balloon3.h
+++ b/arch/arm/mach-pxa/include/mach/balloon3.h
@@ -129,6 +129,16 @@ enum balloon3_features {
 #define CPLD_AROUTING_LOONR2INT_BIT    6
 #define CPLD_AROUTING_LOONR2EXT_BIT    7
 
+/* Balloon3 Interrupts */
+#define BALLOON3_IRQ(x)		(IRQ_BOARD_START + (x))
+
+#define BALLOON3_BP_CF_NRDY_IRQ	BALLOON3_IRQ(0)
+#define BALLOON3_BP_NSTSCHG_IRQ	BALLOON3_IRQ(1)
+
+#define BALLOON3_AUX_NIRQ	IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ)
+#define BALLOON3_CODEC_IRQ	IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ)
+#define BALLOON3_S0_CD_IRQ	IRQ_GPIO(BALLOON3_GPIO_S0_CD)
+
 extern int balloon3_has(enum balloon3_features feature);
 
 #endif
diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h
index e741bf1bfb2..7515757d691 100644
--- a/arch/arm/mach-pxa/include/mach/hardware.h
+++ b/arch/arm/mach-pxa/include/mach/hardware.h
@@ -314,7 +314,6 @@ extern unsigned long get_clock_tick_rate(void);
 #define PCIBIOS_MIN_IO		0
 #define PCIBIOS_MIN_MEM		0
 #define pcibios_assign_all_busses()	1
-#define HAVE_ARCH_PCI_SET_DMA_MASK	1
 #endif
 
 
diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h
index 3677a9af9c8..ffc8314520f 100644
--- a/arch/arm/mach-pxa/include/mach/irqs.h
+++ b/arch/arm/mach-pxa/include/mach/irqs.h
@@ -135,82 +135,6 @@
 #define IRQ_BOARD_END		(IRQ_BOARD_START + 16)
 #endif
 
-#define IRQ_SA1111_START	(IRQ_BOARD_END)
-#define IRQ_GPAIN0		(IRQ_BOARD_END + 0)
-#define IRQ_GPAIN1		(IRQ_BOARD_END + 1)
-#define IRQ_GPAIN2		(IRQ_BOARD_END + 2)
-#define IRQ_GPAIN3		(IRQ_BOARD_END + 3)
-#define IRQ_GPBIN0		(IRQ_BOARD_END + 4)
-#define IRQ_GPBIN1		(IRQ_BOARD_END + 5)
-#define IRQ_GPBIN2		(IRQ_BOARD_END + 6)
-#define IRQ_GPBIN3		(IRQ_BOARD_END + 7)
-#define IRQ_GPBIN4		(IRQ_BOARD_END + 8)
-#define IRQ_GPBIN5		(IRQ_BOARD_END + 9)
-#define IRQ_GPCIN0		(IRQ_BOARD_END + 10)
-#define IRQ_GPCIN1		(IRQ_BOARD_END + 11)
-#define IRQ_GPCIN2		(IRQ_BOARD_END + 12)
-#define IRQ_GPCIN3		(IRQ_BOARD_END + 13)
-#define IRQ_GPCIN4		(IRQ_BOARD_END + 14)
-#define IRQ_GPCIN5		(IRQ_BOARD_END + 15)
-#define IRQ_GPCIN6		(IRQ_BOARD_END + 16)
-#define IRQ_GPCIN7		(IRQ_BOARD_END + 17)
-#define IRQ_MSTXINT		(IRQ_BOARD_END + 18)
-#define IRQ_MSRXINT		(IRQ_BOARD_END + 19)
-#define IRQ_MSSTOPERRINT	(IRQ_BOARD_END + 20)
-#define IRQ_TPTXINT		(IRQ_BOARD_END + 21)
-#define IRQ_TPRXINT		(IRQ_BOARD_END + 22)
-#define IRQ_TPSTOPERRINT	(IRQ_BOARD_END + 23)
-#define SSPXMTINT		(IRQ_BOARD_END + 24)
-#define SSPRCVINT		(IRQ_BOARD_END + 25)
-#define SSPROR			(IRQ_BOARD_END + 26)
-#define AUDXMTDMADONEA		(IRQ_BOARD_END + 32)
-#define AUDRCVDMADONEA		(IRQ_BOARD_END + 33)
-#define AUDXMTDMADONEB		(IRQ_BOARD_END + 34)
-#define AUDRCVDMADONEB		(IRQ_BOARD_END + 35)
-#define AUDTFSR			(IRQ_BOARD_END + 36)
-#define AUDRFSR			(IRQ_BOARD_END + 37)
-#define AUDTUR			(IRQ_BOARD_END + 38)
-#define AUDROR			(IRQ_BOARD_END + 39)
-#define AUDDTS			(IRQ_BOARD_END + 40)
-#define AUDRDD			(IRQ_BOARD_END + 41)
-#define AUDSTO			(IRQ_BOARD_END + 42)
-#define IRQ_USBPWR		(IRQ_BOARD_END + 43)
-#define IRQ_HCIM		(IRQ_BOARD_END + 44)
-#define IRQ_HCIBUFFACC		(IRQ_BOARD_END + 45)
-#define IRQ_HCIRMTWKP		(IRQ_BOARD_END + 46)
-#define IRQ_NHCIMFCIR		(IRQ_BOARD_END + 47)
-#define IRQ_USB_PORT_RESUME	(IRQ_BOARD_END + 48)
-#define IRQ_S0_READY_NINT	(IRQ_BOARD_END + 49)
-#define IRQ_S1_READY_NINT	(IRQ_BOARD_END + 50)
-#define IRQ_S0_CD_VALID		(IRQ_BOARD_END + 51)
-#define IRQ_S1_CD_VALID		(IRQ_BOARD_END + 52)
-#define IRQ_S0_BVD1_STSCHG	(IRQ_BOARD_END + 53)
-#define IRQ_S1_BVD1_STSCHG	(IRQ_BOARD_END + 54)
-
-#define IRQ_LOCOMO_START	(IRQ_BOARD_END)
-#define IRQ_LOCOMO_KEY		(IRQ_BOARD_END + 0)
-#define IRQ_LOCOMO_GPIO0	(IRQ_BOARD_END + 1)
-#define IRQ_LOCOMO_GPIO1	(IRQ_BOARD_END + 2)
-#define IRQ_LOCOMO_GPIO2	(IRQ_BOARD_END + 3)
-#define IRQ_LOCOMO_GPIO3	(IRQ_BOARD_END + 4)
-#define IRQ_LOCOMO_GPIO4	(IRQ_BOARD_END + 5)
-#define IRQ_LOCOMO_GPIO5	(IRQ_BOARD_END + 6)
-#define IRQ_LOCOMO_GPIO6	(IRQ_BOARD_END + 7)
-#define IRQ_LOCOMO_GPIO7	(IRQ_BOARD_END + 8)
-#define IRQ_LOCOMO_GPIO8	(IRQ_BOARD_END + 9)
-#define IRQ_LOCOMO_GPIO9	(IRQ_BOARD_END + 10)
-#define IRQ_LOCOMO_GPIO10	(IRQ_BOARD_END + 11)
-#define IRQ_LOCOMO_GPIO11	(IRQ_BOARD_END + 12)
-#define IRQ_LOCOMO_GPIO12	(IRQ_BOARD_END + 13)
-#define IRQ_LOCOMO_GPIO13	(IRQ_BOARD_END + 14)
-#define IRQ_LOCOMO_GPIO14	(IRQ_BOARD_END + 15)
-#define IRQ_LOCOMO_GPIO15	(IRQ_BOARD_END + 16)
-#define IRQ_LOCOMO_LT		(IRQ_BOARD_END + 17)
-#define IRQ_LOCOMO_SPI_RFR	(IRQ_BOARD_END + 18)
-#define IRQ_LOCOMO_SPI_RFW	(IRQ_BOARD_END + 19)
-#define IRQ_LOCOMO_SPI_OVRN	(IRQ_BOARD_END + 20)
-#define IRQ_LOCOMO_SPI_TEND	(IRQ_BOARD_END + 21)
-
 /*
  * Figure out the MAX IRQ number.
  *
@@ -219,89 +143,16 @@
  * Otherwise, we have the standard IRQs only.
  */
 #ifdef CONFIG_SA1111
-#define NR_IRQS			(IRQ_S1_BVD1_STSCHG + 1)
-#elif defined(CONFIG_SHARP_LOCOMO)
-#define NR_IRQS			(IRQ_LOCOMO_SPI_TEND + 1)
+#define NR_IRQS			(IRQ_BOARD_END + 55)
 #elif defined(CONFIG_PXA_HAVE_BOARD_IRQS)
 #define NR_IRQS			(IRQ_BOARD_END)
 #else
 #define NR_IRQS			(IRQ_BOARD_START)
 #endif
 
-/*
- * Board specific IRQs.  Define them here.
- * Do not surround them with ifdefs.
- */
-#define LUBBOCK_IRQ(x)		(IRQ_BOARD_START + (x))
-#define LUBBOCK_SD_IRQ		LUBBOCK_IRQ(0)
-#define LUBBOCK_SA1111_IRQ	LUBBOCK_IRQ(1)
-#define LUBBOCK_USB_IRQ		LUBBOCK_IRQ(2)  /* usb connect */
-#define LUBBOCK_ETH_IRQ		LUBBOCK_IRQ(3)
-#define LUBBOCK_UCB1400_IRQ	LUBBOCK_IRQ(4)
-#define LUBBOCK_BB_IRQ		LUBBOCK_IRQ(5)
-#define LUBBOCK_USB_DISC_IRQ	LUBBOCK_IRQ(6)  /* usb disconnect */
-#define LUBBOCK_LAST_IRQ	LUBBOCK_IRQ(6)
-
-#define LPD270_IRQ(x)		(IRQ_BOARD_START + (x))
-#define LPD270_USBC_IRQ		LPD270_IRQ(2)
-#define LPD270_ETHERNET_IRQ	LPD270_IRQ(3)
-#define LPD270_AC97_IRQ		LPD270_IRQ(4)
-
-#define MAINSTONE_IRQ(x)	(IRQ_BOARD_START + (x))
-#define MAINSTONE_MMC_IRQ	MAINSTONE_IRQ(0)
-#define MAINSTONE_USIM_IRQ	MAINSTONE_IRQ(1)
-#define MAINSTONE_USBC_IRQ	MAINSTONE_IRQ(2)
-#define MAINSTONE_ETHERNET_IRQ	MAINSTONE_IRQ(3)
-#define MAINSTONE_AC97_IRQ	MAINSTONE_IRQ(4)
-#define MAINSTONE_PEN_IRQ	MAINSTONE_IRQ(5)
-#define MAINSTONE_MSINS_IRQ	MAINSTONE_IRQ(6)
-#define MAINSTONE_EXBRD_IRQ	MAINSTONE_IRQ(7)
-#define MAINSTONE_S0_CD_IRQ	MAINSTONE_IRQ(9)
-#define MAINSTONE_S0_STSCHG_IRQ	MAINSTONE_IRQ(10)
-#define MAINSTONE_S0_IRQ	MAINSTONE_IRQ(11)
-#define MAINSTONE_S1_CD_IRQ	MAINSTONE_IRQ(13)
-#define MAINSTONE_S1_STSCHG_IRQ	MAINSTONE_IRQ(14)
-#define MAINSTONE_S1_IRQ	MAINSTONE_IRQ(15)
-
-/* Balloon3 Interrupts */
-#define BALLOON3_IRQ(x)		(IRQ_BOARD_START + (x))
-
-#define BALLOON3_BP_CF_NRDY_IRQ	BALLOON3_IRQ(0)
-#define BALLOON3_BP_NSTSCHG_IRQ	BALLOON3_IRQ(1)
-
-#define BALLOON3_AUX_NIRQ	IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ)
-#define BALLOON3_CODEC_IRQ	IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ)
-#define BALLOON3_S0_CD_IRQ	IRQ_GPIO(BALLOON3_GPIO_S0_CD)
-
-/* LoCoMo Interrupts (CONFIG_SHARP_LOCOMO) */
-#define IRQ_LOCOMO_KEY_BASE	(IRQ_BOARD_START + 0)
-#define IRQ_LOCOMO_GPIO_BASE	(IRQ_BOARD_START + 1)
-#define IRQ_LOCOMO_LT_BASE	(IRQ_BOARD_START + 2)
-#define IRQ_LOCOMO_SPI_BASE	(IRQ_BOARD_START + 3)
-
-/* phyCORE-PXA270 (PCM027) Interrupts */
-#define PCM027_IRQ(x)          (IRQ_BOARD_START + (x))
-#define PCM027_BTDET_IRQ       PCM027_IRQ(0)
-#define PCM027_FF_RI_IRQ       PCM027_IRQ(1)
-#define PCM027_MMCDET_IRQ      PCM027_IRQ(2)
-#define PCM027_PM_5V_IRQ       PCM027_IRQ(3)
-
-/* ITE8152 irqs */
 /* add IT8152 IRQs beyond BOARD_END */
 #ifdef CONFIG_PCI_HOST_ITE8152
-#define IT8152_IRQ(x)   (IRQ_BOARD_END + (x))
-
-/* IRQ-sources in 3 groups - local devices, LPC (serial), and external PCI */
-#define IT8152_LD_IRQ_COUNT     9
-#define IT8152_LP_IRQ_COUNT     16
-#define IT8152_PD_IRQ_COUNT     15
-
-/* Priorities: */
-#define IT8152_PD_IRQ(i)        IT8152_IRQ(i)
-#define IT8152_LP_IRQ(i)        (IT8152_IRQ(i) + IT8152_PD_IRQ_COUNT)
-#define IT8152_LD_IRQ(i)        (IT8152_IRQ(i) + IT8152_PD_IRQ_COUNT + IT8152_LP_IRQ_COUNT)
-
-#define IT8152_LAST_IRQ         IT8152_LD_IRQ(IT8152_LD_IRQ_COUNT - 1)
+#define IT8152_LAST_IRQ         (IRQ_BOARD_END + 40)
 
 #if NR_IRQS < (IT8152_LAST_IRQ+1)
 #undef NR_IRQS
diff --git a/arch/arm/mach-pxa/include/mach/lpd270.h b/arch/arm/mach-pxa/include/mach/lpd270.h
index f89fb715266..0e6440c8168 100644
--- a/arch/arm/mach-pxa/include/mach/lpd270.h
+++ b/arch/arm/mach-pxa/include/mach/lpd270.h
@@ -34,5 +34,9 @@
 #define LPD270_INT_ETHERNET	(1 << 3)  /* Ethernet controller IRQ */
 #define LPD270_INT_USBC		(1 << 2)  /* USB client cable detection IRQ */
 
+#define LPD270_IRQ(x)		(IRQ_BOARD_START + (x))
+#define LPD270_USBC_IRQ		LPD270_IRQ(2)
+#define LPD270_ETHERNET_IRQ	LPD270_IRQ(3)
+#define LPD270_AC97_IRQ		LPD270_IRQ(4)
 
 #endif
diff --git a/arch/arm/mach-pxa/include/mach/lubbock.h b/arch/arm/mach-pxa/include/mach/lubbock.h
index 751b74811d0..a0d4247f08f 100644
--- a/arch/arm/mach-pxa/include/mach/lubbock.h
+++ b/arch/arm/mach-pxa/include/mach/lubbock.h
@@ -34,6 +34,17 @@
 #define LUB_IRQ_SET_CLR		__LUB_REG(LUBBOCK_FPGA_PHYS + 0x0d0)
 #define LUB_GP			__LUB_REG(LUBBOCK_FPGA_PHYS + 0x100)
 
+/* Board specific IRQs */
+#define LUBBOCK_IRQ(x)		(IRQ_BOARD_START + (x))
+#define LUBBOCK_SD_IRQ		LUBBOCK_IRQ(0)
+#define LUBBOCK_SA1111_IRQ	LUBBOCK_IRQ(1)
+#define LUBBOCK_USB_IRQ		LUBBOCK_IRQ(2)  /* usb connect */
+#define LUBBOCK_ETH_IRQ		LUBBOCK_IRQ(3)
+#define LUBBOCK_UCB1400_IRQ	LUBBOCK_IRQ(4)
+#define LUBBOCK_BB_IRQ		LUBBOCK_IRQ(5)
+#define LUBBOCK_USB_DISC_IRQ	LUBBOCK_IRQ(6)  /* usb disconnect */
+#define LUBBOCK_LAST_IRQ	LUBBOCK_IRQ(6)
+
 #ifndef __ASSEMBLY__
 extern void lubbock_set_misc_wr(unsigned int mask, unsigned int set);
 #endif
diff --git a/arch/arm/mach-pxa/include/mach/mainstone.h b/arch/arm/mach-pxa/include/mach/mainstone.h
index 3461c4302ff..86e623abd64 100644
--- a/arch/arm/mach-pxa/include/mach/mainstone.h
+++ b/arch/arm/mach-pxa/include/mach/mainstone.h
@@ -117,4 +117,21 @@
 #define MST_PCMCIA_PWR_VCC_33   0x8	   /* voltage VCC = 3.3V */
 #define MST_PCMCIA_PWR_VCC_50   0x4	   /* voltage VCC = 5.0V */
 
+/* board specific IRQs */
+#define MAINSTONE_IRQ(x)	(IRQ_BOARD_START + (x))
+#define MAINSTONE_MMC_IRQ	MAINSTONE_IRQ(0)
+#define MAINSTONE_USIM_IRQ	MAINSTONE_IRQ(1)
+#define MAINSTONE_USBC_IRQ	MAINSTONE_IRQ(2)
+#define MAINSTONE_ETHERNET_IRQ	MAINSTONE_IRQ(3)
+#define MAINSTONE_AC97_IRQ	MAINSTONE_IRQ(4)
+#define MAINSTONE_PEN_IRQ	MAINSTONE_IRQ(5)
+#define MAINSTONE_MSINS_IRQ	MAINSTONE_IRQ(6)
+#define MAINSTONE_EXBRD_IRQ	MAINSTONE_IRQ(7)
+#define MAINSTONE_S0_CD_IRQ	MAINSTONE_IRQ(9)
+#define MAINSTONE_S0_STSCHG_IRQ	MAINSTONE_IRQ(10)
+#define MAINSTONE_S0_IRQ	MAINSTONE_IRQ(11)
+#define MAINSTONE_S1_CD_IRQ	MAINSTONE_IRQ(13)
+#define MAINSTONE_S1_STSCHG_IRQ	MAINSTONE_IRQ(14)
+#define MAINSTONE_S1_IRQ	MAINSTONE_IRQ(15)
+
 #endif
diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h
index 9c787855cf2..cafadc33dfd 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h
@@ -190,4 +190,36 @@
 #define GPIO89_AC97_nRESET	MFP_CFG_OUT(GPIO89, AF0, DRIVE_HIGH)
 #endif	/* CONFIG_CPU_PXA26x */
 
+/* commonly used pin configurations */
+#define GPIOxx_LCD_16BPP	\
+	GPIO58_LCD_LDD_0,	\
+	GPIO59_LCD_LDD_1,	\
+	GPIO60_LCD_LDD_2,	\
+	GPIO61_LCD_LDD_3,	\
+	GPIO62_LCD_LDD_4,	\
+	GPIO63_LCD_LDD_5,	\
+	GPIO64_LCD_LDD_6,	\
+	GPIO65_LCD_LDD_7,	\
+	GPIO66_LCD_LDD_8,	\
+	GPIO67_LCD_LDD_9,	\
+	GPIO68_LCD_LDD_10,	\
+	GPIO69_LCD_LDD_11,	\
+	GPIO70_LCD_LDD_12,	\
+	GPIO71_LCD_LDD_13,	\
+	GPIO72_LCD_LDD_14,	\
+	GPIO73_LCD_LDD_15
+
+#define GPIOxx_LCD_DSTN_16BPP	\
+	GPIOxx_LCD_16BPP,	\
+	GPIO74_LCD_FCLK,	\
+	GPIO75_LCD_LCLK,	\
+	GPIO76_LCD_PCLK
+
+#define GPIOxx_LCD_TFT_16BPP	\
+	GPIOxx_LCD_16BPP,	\
+	GPIO74_LCD_FCLK,	\
+	GPIO75_LCD_LCLK,	\
+	GPIO76_LCD_PCLK,	\
+	GPIO77_LCD_BIAS
+
 #endif /* __ASM_ARCH_MFP_PXA25X_H */
diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
index 6543c05f47e..ec0f0b0b674 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
@@ -434,5 +434,32 @@
 #define GPIO112_nMSINS		MFP_CFG_IN(GPIO112, AF2)
 #define GPIO32_MSSCLK		MFP_CFG_OUT(GPIO32, AF1, DRIVE_LOW)
 
+/* commonly used pin configurations */
+#define GPIOxx_LCD_16BPP	\
+	GPIO58_LCD_LDD_0,	\
+	GPIO59_LCD_LDD_1,	\
+	GPIO60_LCD_LDD_2,	\
+	GPIO61_LCD_LDD_3,	\
+	GPIO62_LCD_LDD_4,	\
+	GPIO63_LCD_LDD_5,	\
+	GPIO64_LCD_LDD_6,	\
+	GPIO65_LCD_LDD_7,	\
+	GPIO66_LCD_LDD_8,	\
+	GPIO67_LCD_LDD_9,	\
+	GPIO68_LCD_LDD_10,	\
+	GPIO69_LCD_LDD_11,	\
+	GPIO70_LCD_LDD_12,	\
+	GPIO71_LCD_LDD_13,	\
+	GPIO72_LCD_LDD_14,	\
+	GPIO73_LCD_LDD_15
+
+#define GPIOxx_LCD_TFT_16BPP	\
+	GPIOxx_LCD_16BPP,	\
+	GPIO74_LCD_FCLK,	\
+	GPIO75_LCD_LCLK,	\
+	GPIO76_LCD_PCLK,	\
+	GPIO77_LCD_BIAS
+
+
 extern int keypad_set_wake(unsigned int on);
 #endif /* __ASM_ARCH_MFP_PXA27X_H */
diff --git a/arch/arm/mach-pxa/include/mach/mxm8x10.h b/arch/arm/mach-pxa/include/mach/mxm8x10.h
new file mode 100644
index 00000000000..ffa15665a41
--- /dev/null
+++ b/arch/arm/mach-pxa/include/mach/mxm8x10.h
@@ -0,0 +1,21 @@
+#ifndef __MACH_MXM_8X10_H
+#define __MACH_MXM_8X10_H
+
+#define MXM_8X10_ETH_PHYS	0x13000000
+
+#if defined(CONFIG_MMC)
+
+#define MXM_8X10_SD_nCD (72)
+#define MXM_8X10_SD_WP (84)
+
+extern void mxm_8x10_mmc_init(void);
+#else
+static inline void mxm_8x10_mmc_init(void) {}
+#endif
+
+extern void mxm_8x10_usb_host_init(void);
+extern void mxm_8x10_ac97_init(void);
+
+extern void mxm_8x10_barebones_init(void);
+
+#endif /* __MACH_MXM_8X10_H */
diff --git a/arch/arm/mach-pxa/include/mach/pcm027.h b/arch/arm/mach-pxa/include/mach/pcm027.h
index 4dcd2e8baa6..04083263167 100644
--- a/arch/arm/mach-pxa/include/mach/pcm027.h
+++ b/arch/arm/mach-pxa/include/mach/pcm027.h
@@ -23,6 +23,13 @@
  * Definitions of CPU card resources only
  */
 
+/* phyCORE-PXA270 (PCM027) Interrupts */
+#define PCM027_IRQ(x)          (IRQ_BOARD_START + (x))
+#define PCM027_BTDET_IRQ       PCM027_IRQ(0)
+#define PCM027_FF_RI_IRQ       PCM027_IRQ(1)
+#define PCM027_MMCDET_IRQ      PCM027_IRQ(2)
+#define PCM027_PM_5V_IRQ       PCM027_IRQ(3)
+
 /* I2C RTC */
 #define PCM027_RTC_IRQ_GPIO	0
 #define PCM027_RTC_IRQ		IRQ_GPIO(PCM027_RTC_IRQ_GPIO)
diff --git a/arch/arm/mach-pxa/include/mach/ssp.h b/arch/arm/mach-pxa/include/mach/ssp.h
index cb5cb766f0f..be1be5b6db5 100644
--- a/arch/arm/mach-pxa/include/mach/ssp.h
+++ b/arch/arm/mach-pxa/include/mach/ssp.h
@@ -46,6 +46,7 @@ struct ssp_device {
 	int		drcmr_tx;
 };
 
+#ifdef CONFIG_PXA_SSP_LEGACY
 /*
  * SSP initialisation flags
  */
@@ -78,6 +79,7 @@ void ssp_restore_state(struct ssp_dev *dev, struct ssp_state *ssp);
 int ssp_init(struct ssp_dev *dev, u32 port, u32 init_flags);
 int ssp_config(struct ssp_dev *dev, u32 mode, u32 flags, u32 psp_flags, u32 speed);
 void ssp_exit(struct ssp_dev *dev);
+#endif /* CONFIG_PXA_SSP_LEGACY */
 
 /**
  * ssp_write_reg - Write to a SSP register
diff --git a/arch/arm/mach-pxa/include/mach/uncompress.h b/arch/arm/mach-pxa/include/mach/uncompress.h
index 237734b5b1b..5ef91d9d17e 100644
--- a/arch/arm/mach-pxa/include/mach/uncompress.h
+++ b/arch/arm/mach-pxa/include/mach/uncompress.h
@@ -10,20 +10,41 @@
  */
 
 #include <linux/serial_reg.h>
-#include <mach/regs-uart.h>
 #include <asm/mach-types.h>
 
-#define __REG(x)       ((volatile unsigned long *)x)
+#define FFUART_BASE	(0x40100000)
+#define BTUART_BASE	(0x40200000)
+#define STUART_BASE	(0x40700000)
 
-static volatile unsigned long *UART = FFUART;
+static unsigned long uart_base = FFUART_BASE;
+static unsigned int uart_shift = 2;
+static unsigned int uart_is_pxa = 1;
+
+static inline unsigned char uart_read(int offset)
+{
+	return *(volatile unsigned char *)(uart_base + (offset << uart_shift));
+}
+
+static inline void uart_write(unsigned char val, int offset)
+{
+	*(volatile unsigned char *)(uart_base + (offset << uart_shift)) = val;
+}
+
+static inline int uart_is_enabled(void)
+{
+	/* assume enabled by default for non-PXA uarts */
+	return uart_is_pxa ? uart_read(UART_IER) & UART_IER_UUE : 1;
+}
 
 static inline void putc(char c)
 {
-	if (!(UART[UART_IER] & IER_UUE))
+	if (!uart_is_enabled())
 		return;
-	while (!(UART[UART_LSR] & LSR_TDRQ))
+
+	while (!(uart_read(UART_LSR) & UART_LSR_THRE))
 		barrier();
-	UART[UART_TX] = c;
+
+	uart_write(c, UART_TX);
 }
 
 /*
@@ -38,7 +59,13 @@ static inline void arch_decomp_setup(void)
 	if (machine_is_littleton() || machine_is_intelmote2()
 	    || machine_is_csb726() || machine_is_stargate2()
 	    || machine_is_cm_x300() || machine_is_balloon3())
-		UART = STUART;
+		uart_base = STUART_BASE;
+
+	if (machine_is_arcom_zeus()) {
+		uart_base = 0x10000000;	/* nCS4 */
+		uart_shift = 1;
+		uart_is_pxa = 0;
+	}
 }
 
 /*
diff --git a/arch/arm/mach-pxa/include/mach/zeus.h b/arch/arm/mach-pxa/include/mach/zeus.h
index c387046d2f2..6e119976003 100644
--- a/arch/arm/mach-pxa/include/mach/zeus.h
+++ b/arch/arm/mach-pxa/include/mach/zeus.h
@@ -58,6 +58,8 @@
 #define ZEUS_EXT1_GPIO(x)	(ZEUS_EXT1_GPIO_BASE + (x))
 #define ZEUS_USER_GPIO(x)	(ZEUS_USER_GPIO_BASE + (x))
 
+#define	ZEUS_CAN_SHDN_GPIO	ZEUS_EXT1_GPIO(2)
+
 /*
  * CPLD registers:
  * Only 4 registers, but spreaded over a 32MB address space.
@@ -68,7 +70,6 @@
 #define ZEUS_CPLD_VERSION	(ZEUS_CPLD + 0x0000)
 #define ZEUS_CPLD_ISA_IRQ	(ZEUS_CPLD + 0x1000)
 #define ZEUS_CPLD_CONTROL	(ZEUS_CPLD + 0x2000)
-#define ZEUS_CPLD_EXTWDOG	(ZEUS_CPLD + 0x3000)
 
 /* CPLD register bits */
 #define ZEUS_CPLD_CONTROL_CF_RST        0x01
diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c
index 1373c22dbb8..d279507fc74 100644
--- a/arch/arm/mach-pxa/lpd270.c
+++ b/arch/arm/mach-pxa/lpd270.c
@@ -83,6 +83,10 @@ static unsigned long lpd270_pin_config[] __initdata = {
 	GPIO89_USBH1_PEN,
 
 	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
 	GPIO45_AC97_SYSCLK,
 
 	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
@@ -121,7 +125,7 @@ static void lpd270_irq_handler(unsigned int irq, struct irq_desc *desc)
 
 	pending = __raw_readw(LPD270_INT_STATUS) & lpd270_irq_enabled;
 	do {
-		GEDR(0) = GPIO_bit(0);  /* clear useless edge notification */
+		desc->chip->ack(irq);	/* clear useless edge notification */
 		if (likely(pending)) {
 			irq = LPD270_IRQ(0) + __ffs(pending);
 			generic_handle_irq(irq);
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c
index 98ee7e59029..63d65a2a038 100644
--- a/arch/arm/mach-pxa/lubbock.c
+++ b/arch/arm/mach-pxa/lubbock.c
@@ -66,26 +66,14 @@ static unsigned long lubbock_pin_config[] __initdata = {
 	GPIO25_SSP1_TXD,
 	GPIO26_SSP1_RXD,
 
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+
 	/* LCD - 16bpp DSTN */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
+	GPIOxx_LCD_DSTN_16BPP,
 
 	/* BTUART */
 	GPIO42_BTUART_RXD,
@@ -158,7 +146,7 @@ static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc)
 {
 	unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
 	do {
-		GEDR(0) = GPIO_bit(0);	/* clear our parent irq */
+		desc->chip->ack(irq);	/* clear our parent irq */
 		if (likely(pending)) {
 			irq = LUBBOCK_IRQ(0) + __ffs(pending);
 			generic_handle_irq(irq);
@@ -240,11 +228,18 @@ static struct resource sa1111_resources[] = {
 	},
 };
 
+static struct sa1111_platform_data sa1111_info = {
+	.irq_base	= IRQ_BOARD_END,
+};
+
 static struct platform_device sa1111_device = {
 	.name		= "sa1111",
 	.id		= -1,
 	.num_resources	= ARRAY_SIZE(sa1111_resources),
 	.resource	= sa1111_resources,
+	.dev		= {
+		.platform_data	= &sa1111_info,
+	},
 };
 
 /* ADS7846 is connected through SSP ... and if your board has J5 populated,
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index 189f330719a..e81dd0c8e40 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -88,26 +88,7 @@ static unsigned long magician_pin_config[] __initdata = {
 	GPIO112_MMC_CMD,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* QCI */
 	GPIO12_CIF_DD_7,
diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c
index 851ee0fc32e..5543c64da9e 100644
--- a/arch/arm/mach-pxa/mainstone.c
+++ b/arch/arm/mach-pxa/mainstone.c
@@ -60,26 +60,7 @@ static unsigned long mainstone_pin_config[] = {
 	GPIO15_nCS_1,
 
 	/* LCD - 16bpp Active TFT */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 	GPIO16_PWM0_OUT,	/* Backlight */
 
 	/* MMC */
@@ -107,6 +88,10 @@ static unsigned long mainstone_pin_config[] = {
 	GPIO57_nIOIS16,
 
 	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
 	GPIO45_AC97_SYSCLK,
 
 	/* Keypad */
@@ -162,7 +147,7 @@ static void mainstone_irq_handler(unsigned int irq, struct irq_desc *desc)
 {
 	unsigned long pending = MST_INTSETCLR & mainstone_irq_enabled;
 	do {
-		GEDR(0) = GPIO_bit(0);  /* clear useless edge notification */
+		desc->chip->ack(irq);	/* clear useless edge notification */
 		if (likely(pending)) {
 			irq = MAINSTONE_IRQ(0) + __ffs(pending);
 			generic_handle_irq(irq);
diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c
index 2466a44d8fd..843fcca76e2 100644
--- a/arch/arm/mach-pxa/mioa701.c
+++ b/arch/arm/mach-pxa/mioa701.c
@@ -86,25 +86,7 @@ static unsigned long mioa701_pin_config[] = {
 	MIO_CFG_OUT(GPIO22_USB_ENABLE, AF0, DRIVE_LOW),
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* QCI */
 	GPIO12_CIF_DD_7,
@@ -155,6 +137,10 @@ static unsigned long mioa701_pin_config[] = {
 	GPIO41_FFUART_RTS,
 
 	/* Sound */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
 	GPIO89_AC97_SYSCLK,
 	MIO_CFG_IN(GPIO12_HPJACK_INSERT, AF0),
 
diff --git a/arch/arm/mach-pxa/mxm8x10.c b/arch/arm/mach-pxa/mxm8x10.c
new file mode 100644
index 00000000000..8c9c6f0d56b
--- /dev/null
+++ b/arch/arm/mach-pxa/mxm8x10.c
@@ -0,0 +1,474 @@
+/*
+ * linux/arch/arm/mach-pxa/mxm8x10.c
+ *
+ * Support for the Embedian MXM-8x10 Computer on Module
+ *
+ * Copyright (C) 2006 Marvell International Ltd.
+ * Copyright (C) 2009 Embedian Inc.
+ * Copyright (C) 2009 TMT Services & Supplies (Pty) Ltd.
+ *
+ * 2007-09-04: eric miao <eric.y.miao@gmail.com>
+ *             rewrite to align with latest kernel
+ *
+ * 2010-01-09: Edwin Peer <epeer@tmtservices.co.za>
+ * 	       Hennie van der Merwe <hvdmerwe@tmtservices.co.za>
+ *             rework for upstream merge
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/serial_8250.h>
+#include <linux/dm9000.h>
+#include <linux/gpio.h>
+
+#include <plat/i2c.h>
+#include <plat/pxa3xx_nand.h>
+
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/ohci.h>
+#include <mach/pxa320.h>
+
+#include <mach/mxm8x10.h>
+
+#include "devices.h"
+#include "generic.h"
+
+/* GPIO pin definition
+
+External device stuff   - Leave unconfigured for now...
+---------------------
+GPIO0   -   DREQ    (External DMA Request)
+GPIO3   -   nGCS2   (External Chip Select) Where is nGCS0; nGCS1; nGCS4; nGCS5 ?
+GPIO4   -   nGCS3
+GPIO15  -   EXT_GPIO1
+GPIO16  -   EXT_GPIO2
+GPIO17  -   EXT_GPIO3
+GPIO24  -   EXT_GPIO4
+GPIO25  -   EXT_GPIO5
+GPIO26  -   EXT_GPIO6
+GPIO27  -   EXT_GPIO7
+GPIO28  -   EXT_GPIO8
+GPIO29  -   EXT_GPIO9
+GPIO30  -   EXT_GPIO10
+GPIO31  -   EXT_GPIO11
+GPIO57  -   EXT_GPIO12
+GPIO74  -   EXT_IRQ1
+GPIO75  -   EXT_IRQ2
+GPIO76  -   EXT_IRQ3
+GPIO77  -   EXT_IRQ4
+GPIO78  -   EXT_IRQ5
+GPIO79  -   EXT_IRQ6
+GPIO80  -   EXT_IRQ7
+GPIO81  -   EXT_IRQ8
+GPIO87  -   VCCIO_PWREN (External Device PWREN)
+
+Dallas 1-Wire   - Leave unconfigured for now...
+-------------
+GPIO0_2 -   DS - 1Wire
+
+Ethernet
+--------
+GPIO1   -   DM9000 PWR
+GPIO9   -   DM9K_nIRQ
+GPIO36  -   DM9K_RESET
+
+Keypad  - Leave unconfigured by for now...
+------
+GPIO1_2 -   KP_DKIN0
+GPIO5_2 -   KP_MKOUT7
+GPIO82  -   KP_DKIN1
+GPIO85  -   KP_DKIN2
+GPIO86  -   KP_DKIN3
+GPIO113 -   KP_MKIN0
+GPIO114 -   KP_MKIN1
+GPIO115 -   KP_MKIN2
+GPIO116 -   KP_MKIN3
+GPIO117 -   KP_MKIN4
+GPIO118 -   KP_MKIN5
+GPIO119 -   KP_MKIN6
+GPIO120 -   KP_MKIN7
+GPIO121 -   KP_MKOUT0
+GPIO122 -   KP_MKOUT1
+GPIO122 -   KP_MKOUT2
+GPIO123 -   KP_MKOUT3
+GPIO124 -   KP_MKOUT4
+GPIO125 -   KP_MKOUT5
+GPIO127 -   KP_MKOUT6
+
+Data Bus    - Leave unconfigured for now...
+--------
+GPIO2   -   nWait (Data Bus)
+
+USB Device
+----------
+GPIO4_2 -   USBD_PULLUP
+GPIO10  -   UTM_CLK (USB Device UTM Clk)
+GPIO49  -   USB 2.0 Device UTM_DATA0
+GPIO50  -   USB 2.0 Device UTM_DATA1
+GPIO51  -   USB 2.0 Device UTM_DATA2
+GPIO52  -   USB 2.0 Device UTM_DATA3
+GPIO53  -   USB 2.0 Device UTM_DATA4
+GPIO54  -   USB 2.0 Device UTM_DATA5
+GPIO55  -   USB 2.0 Device UTM_DATA6
+GPIO56  -   USB 2.0 Device UTM_DATA7
+GPIO58  -   UTM_RXVALID (USB 2.0 Device)
+GPIO59  -   UTM_RXACTIVE (USB 2.0 Device)
+GPIO60  -   UTM_RXERROR
+GPIO61  -   UTM_OPMODE0
+GPIO62  -   UTM_OPMODE1
+GPIO71  -   USBD_INT    (USB Device?)
+GPIO73  -   UTM_TXREADY (USB 2.0 Device)
+GPIO83  -   UTM_TXVALID (USB 2.0 Device)
+GPIO98  -   UTM_RESET   (USB 2.0 device)
+GPIO99  -   UTM_XCVR_SELECT
+GPIO100 -   UTM_TERM_SELECT
+GPIO101 -   UTM_SUSPENDM_X
+GPIO102 -   UTM_LINESTATE0
+GPIO103 -   UTM_LINESTATE1
+
+Card-Bus Interface  - Leave unconfigured for now...
+------------------
+GPIO5   -   nPIOR (I/O space output enable)
+GPIO6   -   nPIOW (I/O space write enable)
+GPIO7   -   nIOS16 (Input from I/O space telling size of data bus)
+GPIO8   -   nPWAIT (Input for inserting wait states)
+
+LCD
+---
+GPIO6_2     -   LDD0
+GPIO7_2     -   LDD1
+GPIO8_2     -   LDD2
+GPIO9_2     -   LDD3
+GPIO11_2    -   LDD5
+GPIO12_2    -   LDD6
+GPIO13_2    -   LDD7
+GPIO14_2    -   VSYNC
+GPIO15_2    -   HSYNC
+GPIO16_2    -   VCLK
+GPIO17_2    -   HCLK
+GPIO18_2    -   VDEN
+GPIO63      -   LDD8    (CPU LCD)
+GPIO64      -   LDD9    (CPU LCD)
+GPIO65      -   LDD10   (CPU LCD)
+GPIO66      -   LDD11   (CPU LCD)
+GPIO67      -   LDD12   (CPU LCD)
+GPIO68      -   LDD13   (CPU LCD)
+GPIO69      -   LDD14   (CPU LCD)
+GPIO70      -   LDD15   (CPU LCD)
+GPIO88      -   VCCLCD_PWREN (LCD Panel PWREN)
+GPIO97      -   BACKLIGHT_EN
+GPIO104     -   LCD_PWREN
+
+PWM   - Leave unconfigured for now...
+---
+GPIO11  -   PWM0
+GPIO12  -   PWM1
+GPIO13  -   PWM2
+GPIO14  -   PWM3
+
+SD-CARD
+-------
+GPIO18  -   SDDATA0
+GPIO19  -   SDDATA1
+GPIO20  -   SDDATA2
+GPIO21  -   SDDATA3
+GPIO22  -   SDCLK
+GPIO23  -   SDCMD
+GPIO72  -   SD_WP
+GPIO84  -   SD_nIRQ_CD  (SD-Card)
+
+I2C
+---
+GPIO32  -   I2CSCL
+GPIO33  -   I2CSDA
+
+AC97
+----
+GPIO35  -   AC97_SDATA_IN
+GPIO37  -   AC97_SDATA_OUT
+GPIO38  -   AC97_SYNC
+GPIO39  -   AC97_BITCLK
+GPIO40  -   AC97_nRESET
+
+UART1
+-----
+GPIO41  -   UART_RXD1
+GPIO42  -   UART_TXD1
+GPIO43  -   UART_CTS1
+GPIO44  -   UART_DCD1
+GPIO45  -   UART_DSR1
+GPIO46  -   UART_nRI1
+GPIO47  -   UART_DTR1
+GPIO48  -   UART_RTS1
+
+UART2
+-----
+GPIO109 -   RTS2
+GPIO110 -   RXD2
+GPIO111 -   TXD2
+GPIO112 -   nCTS2
+
+UART3
+-----
+GPIO105 -   nCTS3
+GPIO106 -   nRTS3
+GPIO107 -   TXD3
+GPIO108 -   RXD3
+
+SSP3    - Leave unconfigured for now...
+----
+GPIO89  -   SSP3_CLK
+GPIO90  -   SSP3_SFRM
+GPIO91  -   SSP3_TXD
+GPIO92  -   SSP3_RXD
+
+SSP4
+GPIO93  -   SSP4_CLK
+GPIO94  -   SSP4_SFRM
+GPIO95  -   SSP4_TXD
+GPIO96  -   SSP4_RXD
+*/
+
+static mfp_cfg_t mfp_cfg[] __initdata = {
+	/* USB */
+	GPIO10_UTM_CLK,
+	GPIO49_U2D_PHYDATA_0,
+	GPIO50_U2D_PHYDATA_1,
+	GPIO51_U2D_PHYDATA_2,
+	GPIO52_U2D_PHYDATA_3,
+	GPIO53_U2D_PHYDATA_4,
+	GPIO54_U2D_PHYDATA_5,
+	GPIO55_U2D_PHYDATA_6,
+	GPIO56_U2D_PHYDATA_7,
+	GPIO58_UTM_RXVALID,
+	GPIO59_UTM_RXACTIVE,
+	GPIO60_U2D_RXERROR,
+	GPIO61_U2D_OPMODE0,
+	GPIO62_U2D_OPMODE1,
+	GPIO71_GPIO, /* USBD_INT */
+	GPIO73_UTM_TXREADY,
+	GPIO83_U2D_TXVALID,
+	GPIO98_U2D_RESET,
+	GPIO99_U2D_XCVR_SEL,
+	GPIO100_U2D_TERM_SEL,
+	GPIO101_U2D_SUSPEND,
+	GPIO102_UTM_LINESTATE_0,
+	GPIO103_UTM_LINESTATE_1,
+	GPIO4_2_GPIO | MFP_PULL_HIGH, /* UTM_PULLUP */
+
+	/* DM9000 */
+	GPIO1_GPIO,
+	GPIO9_GPIO,
+	GPIO36_GPIO,
+
+	/* AC97 */
+	GPIO35_AC97_SDATA_IN_0,
+	GPIO37_AC97_SDATA_OUT,
+	GPIO38_AC97_SYNC,
+	GPIO39_AC97_BITCLK,
+	GPIO40_AC97_nACRESET,
+
+	/* UARTS */
+	GPIO41_UART1_RXD,
+	GPIO42_UART1_TXD,
+	GPIO43_UART1_CTS,
+	GPIO44_UART1_DCD,
+	GPIO45_UART1_DSR,
+	GPIO46_UART1_RI,
+	GPIO47_UART1_DTR,
+	GPIO48_UART1_RTS,
+
+	GPIO109_UART2_RTS,
+	GPIO110_UART2_RXD,
+	GPIO111_UART2_TXD,
+	GPIO112_UART2_CTS,
+
+	GPIO105_UART3_CTS,
+	GPIO106_UART3_RTS,
+	GPIO107_UART3_TXD,
+	GPIO108_UART3_RXD,
+
+	GPIO78_GPIO,
+	GPIO79_GPIO,
+	GPIO80_GPIO,
+	GPIO81_GPIO,
+
+	/* I2C */
+	GPIO32_I2C_SCL,
+	GPIO33_I2C_SDA,
+
+	/* MMC */
+	GPIO18_MMC1_DAT0,
+	GPIO19_MMC1_DAT1,
+	GPIO20_MMC1_DAT2,
+	GPIO21_MMC1_DAT3,
+	GPIO22_MMC1_CLK,
+	GPIO23_MMC1_CMD,
+	GPIO72_GPIO | MFP_PULL_HIGH, /* Card Detect */
+	GPIO84_GPIO | MFP_PULL_LOW, /* Write Protect */
+
+	/* IRQ */
+	GPIO74_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ1 */
+	GPIO75_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ2 */
+	GPIO76_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ3 */
+	GPIO77_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ4 */
+	GPIO78_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ5 */
+	GPIO79_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ6 */
+	GPIO80_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ7 */
+	GPIO81_GPIO | MFP_LPM_EDGE_RISE  /* EXT_IRQ8 */
+};
+
+/* MMC/MCI Support */
+#if defined(CONFIG_MMC)
+static struct pxamci_platform_data mxm_8x10_mci_platform_data = {
+	.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+	.detect_delay = 1,
+	.gpio_card_detect = MXM_8X10_SD_nCD,
+	.gpio_card_ro = MXM_8X10_SD_WP,
+	.gpio_power = -1
+};
+
+void __init mxm_8x10_mmc_init(void)
+{
+	pxa_set_mci_info(&mxm_8x10_mci_platform_data);
+}
+#endif
+
+/* USB Open Host Controler Interface */
+static struct pxaohci_platform_data mxm_8x10_ohci_platform_data = {
+	.port_mode = PMM_NPS_MODE,
+	.flags = ENABLE_PORT_ALL
+};
+
+void __init mxm_8x10_usb_host_init(void)
+{
+	pxa_set_ohci_info(&mxm_8x10_ohci_platform_data);
+}
+
+/* AC97 Sound Support */
+static struct platform_device mxm_8x10_ac97_device = {
+	.name = "pxa2xx-ac97"
+};
+
+void __init mxm_8x10_ac97_init(void)
+{
+	platform_device_register(&mxm_8x10_ac97_device);
+}
+
+/* NAND flash Support */
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#define NAND_BLOCK_SIZE SZ_128K
+#define NB(x)           (NAND_BLOCK_SIZE * (x))
+static struct mtd_partition mxm_8x10_nand_partitions[] = {
+	[0] = {
+	       .name = "boot",
+	       .size = NB(0x002),
+	       .offset = NB(0x000),
+	       .mask_flags = MTD_WRITEABLE
+	},
+	[1] = {
+	       .name = "kernel",
+	       .size = NB(0x010),
+	       .offset = NB(0x002),
+	       .mask_flags = MTD_WRITEABLE
+	},
+	[2] = {
+	       .name = "root",
+	       .size = NB(0x36c),
+	       .offset = NB(0x012)
+	},
+	[3] = {
+	       .name = "bbt",
+	       .size = NB(0x082),
+	       .offset = NB(0x37e),
+	       .mask_flags = MTD_WRITEABLE
+	}
+};
+
+static struct pxa3xx_nand_platform_data mxm_8x10_nand_info = {
+	.enable_arbiter = 1,
+	.keep_config = 1,
+	.parts = mxm_8x10_nand_partitions,
+	.nr_parts = ARRAY_SIZE(mxm_8x10_nand_partitions)
+};
+
+static void __init mxm_8x10_nand_init(void)
+{
+	pxa3xx_set_nand_info(&mxm_8x10_nand_info);
+}
+#else
+static inline void mxm_8x10_nand_init(void) {}
+#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+
+/* Ethernet support: Davicom DM9000 */
+static struct resource dm9k_resources[] = {
+	[0] = {
+	       .start = MXM_8X10_ETH_PHYS + 0x300,
+	       .end = MXM_8X10_ETH_PHYS + 0x300,
+	       .flags = IORESOURCE_MEM
+	},
+	[1] = {
+	       .start = MXM_8X10_ETH_PHYS + 0x308,
+	       .end = MXM_8X10_ETH_PHYS + 0x308,
+	       .flags = IORESOURCE_MEM
+	},
+	[2] = {
+	       .start = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO9)),
+	       .end = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO9)),
+	       .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE
+	}
+};
+
+static struct dm9000_plat_data dm9k_plat_data = {
+	.flags = DM9000_PLATF_16BITONLY
+};
+
+static struct platform_device dm9k_device = {
+	.name = "dm9000",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(dm9k_resources),
+	.resource = dm9k_resources,
+	.dev = {
+		.platform_data = &dm9k_plat_data
+	}
+};
+
+static void __init mxm_8x10_ethernet_init(void)
+{
+	platform_device_register(&dm9k_device);
+}
+
+/* PXA UARTs */
+static void __init mxm_8x10_uarts_init(void)
+{
+	pxa_set_ffuart_info(NULL);
+	pxa_set_btuart_info(NULL);
+	pxa_set_stuart_info(NULL);
+}
+
+/* I2C and Real Time Clock */
+static struct i2c_board_info __initdata mxm_8x10_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("ds1337", 0x68)
+	}
+};
+
+static void __init mxm_8x10_i2c_init(void)
+{
+	i2c_register_board_info(0, mxm_8x10_i2c_devices,
+				ARRAY_SIZE(mxm_8x10_i2c_devices));
+	pxa_set_i2c_info(NULL);
+}
+
+void __init mxm_8x10_barebones_init(void)
+{
+	pxa3xx_mfp_config(ARRAY_AND_SIZE(mfp_cfg));
+
+	mxm_8x10_uarts_init();
+	mxm_8x10_nand_init();
+	mxm_8x10_i2c_init();
+	mxm_8x10_ethernet_init();
+}
diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c
index e100af78b16..f70c75b3876 100644
--- a/arch/arm/mach-pxa/palmld.c
+++ b/arch/arm/mach-pxa/palmld.c
@@ -83,26 +83,7 @@ static unsigned long palmld_pin_config[] __initdata = {
 	GPIO105_KP_MKOUT_2,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* PWM */
 	GPIO16_PWM0_OUT,
diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c
index 8fe3ec27568..d902a813aae 100644
--- a/arch/arm/mach-pxa/palmt5.c
+++ b/arch/arm/mach-pxa/palmt5.c
@@ -87,26 +87,7 @@ static unsigned long palmt5_pin_config[] __initdata = {
 	GPIO105_KP_MKOUT_2,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* PWM */
 	GPIO16_PWM0_OUT,
diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c
index b992f07ece2..717d7a63867 100644
--- a/arch/arm/mach-pxa/palmtc.c
+++ b/arch/arm/mach-pxa/palmtc.c
@@ -84,26 +84,7 @@ static unsigned long palmtc_pin_config[] __initdata = {
 	GPIO36_GPIO,	/* pullup */
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* MATRIX KEYPAD */
 	GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH,	/* in 0 */
diff --git a/arch/arm/mach-pxa/palmte2.c b/arch/arm/mach-pxa/palmte2.c
index dc728d6ab94..3d284ff1a64 100644
--- a/arch/arm/mach-pxa/palmte2.c
+++ b/arch/arm/mach-pxa/palmte2.c
@@ -73,26 +73,7 @@ static unsigned long palmte2_pin_config[] __initdata = {
 	GPIO47_FICP_TXD,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* GPIO KEYS */
 	GPIO5_GPIO,	/* notes */
diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c
index b433bb49671..d8b4469607a 100644
--- a/arch/arm/mach-pxa/palmtreo.c
+++ b/arch/arm/mach-pxa/palmtreo.c
@@ -99,25 +99,7 @@ static unsigned long treo_pin_config[] __initdata = {
 	GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH,	/* Hotsync button */
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* Quick Capture Interface */
 	GPIO84_CIF_FV,
diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c
index b37a025c0b7..007b58c11f8 100644
--- a/arch/arm/mach-pxa/palmtx.c
+++ b/arch/arm/mach-pxa/palmtx.c
@@ -110,26 +110,7 @@ static unsigned long palmtx_pin_config[] __initdata = {
 	GPIO105_KP_MKOUT_2,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* FFUART */
 	GPIO34_FFUART_RXD,
diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c
index 1c5d68a9451..3a7925ca394 100644
--- a/arch/arm/mach-pxa/palmz72.c
+++ b/arch/arm/mach-pxa/palmz72.c
@@ -95,26 +95,8 @@ static unsigned long palmz72_pin_config[] __initdata = {
 	GPIO105_KP_MKOUT_2,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
+
 	GPIO20_GPIO,	/* bl power */
 	GPIO21_GPIO,	/* LCD border switch */
 	GPIO22_GPIO,	/* LCD border color */
diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c
index d5255ae74fe..9d0ecea1760 100644
--- a/arch/arm/mach-pxa/pcm990-baseboard.c
+++ b/arch/arm/mach-pxa/pcm990-baseboard.c
@@ -58,6 +58,12 @@ static unsigned long pcm990_pin_config[] __initdata = {
 	/* I2C */
 	GPIO117_I2C_SCL,
 	GPIO118_I2C_SDA,
+
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
 };
 
 /*
@@ -259,8 +265,7 @@ static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc)
 	unsigned long pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
 
 	do {
-		GEDR(PCM990_CTRL_INT_IRQ_GPIO) =
-					GPIO_bit(PCM990_CTRL_INT_IRQ_GPIO);
+		desc->chip->ack(irq);	/* clear our parent IRQ */
 		if (likely(pending)) {
 			irq = PCM027_IRQ(0) + __ffs(pending);
 			generic_handle_irq(irq);
diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c
index c2b938a4d5c..d58a52415d7 100644
--- a/arch/arm/mach-pxa/poodle.c
+++ b/arch/arm/mach-pxa/poodle.c
@@ -91,26 +91,7 @@ static unsigned long poodle_pin_config[] __initdata = {
 	GPIO35_FFUART_CTS,
 
 	/* LCD */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* PC Card */
 	GPIO48_nPOE,
@@ -193,11 +174,18 @@ static struct resource locomo_resources[] = {
 	},
 };
 
+static struct locomo_platform_data locomo_info = {
+	.irq_base	= IRQ_BOARD_START,
+};
+
 struct platform_device poodle_locomo_device = {
 	.name		= "locomo",
 	.id		= 0,
 	.num_resources	= ARRAY_SIZE(locomo_resources),
 	.resource	= locomo_resources,
+	.dev		= {
+		.platform_data	= &locomo_info,
+	},
 };
 
 EXPORT_SYMBOL(poodle_locomo_device);
diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c
index d783123e2d4..0af36177ff0 100644
--- a/arch/arm/mach-pxa/pxa27x.c
+++ b/arch/arm/mach-pxa/pxa27x.c
@@ -40,6 +40,25 @@ void pxa27x_clear_otgph(void)
 }
 EXPORT_SYMBOL(pxa27x_clear_otgph);
 
+static unsigned long ac97_reset_config[] = {
+	GPIO95_AC97_nRESET,
+	GPIO95_GPIO,
+	GPIO113_AC97_nRESET,
+	GPIO113_GPIO,
+};
+
+void pxa27x_assert_ac97reset(int reset_gpio, int on)
+{
+	if (reset_gpio == 113)
+		pxa2xx_mfp_config(on ? &ac97_reset_config[0] :
+				       &ac97_reset_config[1], 1);
+
+	if (reset_gpio == 95)
+		pxa2xx_mfp_config(on ? &ac97_reset_config[2] :
+				       &ac97_reset_config[3], 1);
+}
+EXPORT_SYMBOL_GPL(pxa27x_assert_ac97reset);
+
 /* Crystal clock: 13MHz */
 #define BASE_CLK	13000000
 
diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c
new file mode 100644
index 00000000000..3184bdc1452
--- /dev/null
+++ b/arch/arm/mach-pxa/raumfeld.c
@@ -0,0 +1,1108 @@
+/*
+ * arch/arm/mach-pxa/raumfeld.c
+ *
+ * Support for the following Raumfeld devices:
+ *
+ * 	* Controller
+ *  	* Connector
+ *  	* Speaker S/M
+ *
+ * See http://www.raumfeld.com for details.
+ *
+ * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sysdev.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/smsc911x.h>
+#include <linux/input.h>
+#include <linux/rotary_encoder.h>
+#include <linux/gpio_keys.h>
+#include <linux/input/eeti_ts.h>
+#include <linux/leds.h>
+#include <linux/w1-gpio.h>
+#include <linux/sched.h>
+#include <linux/pwm_backlight.h>
+#include <linux/i2c.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_gpio.h>
+#include <linux/lis3lv02d.h>
+#include <linux/pda_power.h>
+#include <linux/power_supply.h>
+#include <linux/pda_power.h>
+#include <linux/power_supply.h>
+#include <linux/regulator/max8660.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/consumer.h>
+#include <linux/delay.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/hardware.h>
+#include <mach/pxa3xx-regs.h>
+#include <mach/mfp-pxa3xx.h>
+#include <mach/mfp-pxa300.h>
+#include <mach/ohci.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <plat/i2c.h>
+#include <plat/pxa3xx_nand.h>
+
+#include "generic.h"
+#include "devices.h"
+#include "clock.h"
+
+/* common GPIO	definitions */
+
+/* inputs */
+#define GPIO_ON_OFF		(14)
+#define GPIO_VOLENC_A		(19)
+#define GPIO_VOLENC_B		(20)
+#define GPIO_CHARGE_DONE	(23)
+#define GPIO_CHARGE_IND		(27)
+#define GPIO_TOUCH_IRQ		(32)
+#define GPIO_ETH_IRQ		(40)
+#define GPIO_SPI_MISO		(98)
+#define GPIO_ACCEL_IRQ		(104)
+#define GPIO_RESCUE_BOOT	(115)
+#define GPIO_DOCK_DETECT	(116)
+#define GPIO_KEY1		(117)
+#define GPIO_KEY2		(118)
+#define GPIO_KEY3		(119)
+#define GPIO_CHARGE_USB_OK	(112)
+#define GPIO_CHARGE_DC_OK	(101)
+#define GPIO_CHARGE_USB_SUSP	(102)
+
+/* outputs */
+#define GPIO_SHUTDOWN_SUPPLY	(16)
+#define GPIO_SHUTDOWN_BATT	(18)
+#define GPIO_CHRG_PEN2		(31)
+#define GPIO_TFT_VA_EN		(33)
+#define GPIO_SPDIF_CS		(34)
+#define GPIO_LED2		(35)
+#define GPIO_LED1		(36)
+#define GPIO_SPDIF_RESET	(38)
+#define GPIO_SPI_CLK		(95)
+#define GPIO_MCLK_DAC_CS	(96)
+#define GPIO_SPI_MOSI		(97)
+#define GPIO_W1_PULLUP_ENABLE	(105)
+#define GPIO_DISPLAY_ENABLE	(106)
+#define GPIO_MCLK_RESET		(111)
+#define GPIO_W2W_RESET		(113)
+#define GPIO_W2W_PDN		(114)
+#define GPIO_CODEC_RESET	(120)
+#define GPIO_AUDIO_VA_ENABLE	(124)
+#define GPIO_ACCEL_CS		(125)
+#define GPIO_ONE_WIRE		(126)
+
+/*
+ * GPIO configurations
+ */
+static mfp_cfg_t raumfeld_controller_pin_config[] __initdata = {
+	/* UART1 */
+	GPIO77_UART1_RXD,
+	GPIO78_UART1_TXD,
+	GPIO79_UART1_CTS,
+	GPIO81_UART1_DSR,
+	GPIO83_UART1_DTR,
+	GPIO84_UART1_RTS,
+
+	/* UART3 */
+	GPIO110_UART3_RXD,
+
+	/* USB Host */
+	GPIO0_2_USBH_PEN,
+	GPIO1_2_USBH_PWR,
+
+	/* I2C */
+	GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
+	GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
+
+	/* SPI */
+	GPIO34_GPIO,	/* SPDIF_CS */
+	GPIO96_GPIO,	/* MCLK_CS */
+	GPIO125_GPIO,	/* ACCEL_CS */
+
+	/* MMC */
+	GPIO3_MMC1_DAT0,
+	GPIO4_MMC1_DAT1,
+	GPIO5_MMC1_DAT2,
+	GPIO6_MMC1_DAT3,
+	GPIO7_MMC1_CLK,
+	GPIO8_MMC1_CMD,
+
+	/* One-wire */
+	GPIO126_GPIO | MFP_LPM_FLOAT,
+	GPIO105_GPIO | MFP_PULL_LOW | MFP_LPM_PULL_LOW,
+
+	/* CHRG_USB_OK */
+	GPIO101_GPIO | MFP_PULL_HIGH,
+	/* CHRG_USB_OK */
+	GPIO112_GPIO | MFP_PULL_HIGH,
+	/* CHRG_USB_SUSP */
+	GPIO102_GPIO,
+	/* DISPLAY_ENABLE */
+	GPIO106_GPIO,
+	/* DOCK_DETECT */
+	GPIO116_GPIO | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
+
+	/* LCD */
+	GPIO54_LCD_LDD_0,
+	GPIO55_LCD_LDD_1,
+	GPIO56_LCD_LDD_2,
+	GPIO57_LCD_LDD_3,
+	GPIO58_LCD_LDD_4,
+	GPIO59_LCD_LDD_5,
+	GPIO60_LCD_LDD_6,
+	GPIO61_LCD_LDD_7,
+	GPIO62_LCD_LDD_8,
+	GPIO63_LCD_LDD_9,
+	GPIO64_LCD_LDD_10,
+	GPIO65_LCD_LDD_11,
+	GPIO66_LCD_LDD_12,
+	GPIO67_LCD_LDD_13,
+	GPIO68_LCD_LDD_14,
+	GPIO69_LCD_LDD_15,
+	GPIO70_LCD_LDD_16,
+	GPIO71_LCD_LDD_17,
+	GPIO72_LCD_FCLK,
+	GPIO73_LCD_LCLK,
+	GPIO74_LCD_PCLK,
+	GPIO75_LCD_BIAS,
+};
+
+static mfp_cfg_t raumfeld_connector_pin_config[] __initdata = {
+	/* UART1 */
+	GPIO77_UART1_RXD,
+	GPIO78_UART1_TXD,
+	GPIO79_UART1_CTS,
+	GPIO81_UART1_DSR,
+	GPIO83_UART1_DTR,
+	GPIO84_UART1_RTS,
+
+	/* UART3 */
+	GPIO110_UART3_RXD,
+
+	/* USB Host */
+	GPIO0_2_USBH_PEN,
+	GPIO1_2_USBH_PWR,
+
+	/* I2C */
+	GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
+	GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
+
+	/* SPI */
+	GPIO34_GPIO,	/* SPDIF_CS */
+	GPIO96_GPIO,	/* MCLK_CS */
+	GPIO125_GPIO,	/* ACCEL_CS */
+
+	/* MMC */
+	GPIO3_MMC1_DAT0,
+	GPIO4_MMC1_DAT1,
+	GPIO5_MMC1_DAT2,
+	GPIO6_MMC1_DAT3,
+	GPIO7_MMC1_CLK,
+	GPIO8_MMC1_CMD,
+
+	/* Ethernet */
+	GPIO1_nCS2,			/* CS */
+	GPIO40_GPIO | MFP_PULL_HIGH,	/* IRQ */
+
+	/* SSP for I2S */
+	GPIO85_SSP1_SCLK,
+	GPIO89_SSP1_EXTCLK,
+	GPIO86_SSP1_FRM,
+	GPIO87_SSP1_TXD,
+	GPIO88_SSP1_RXD,
+	GPIO90_SSP1_SYSCLK,
+
+	/* SSP2 for S/PDIF */
+	GPIO25_SSP2_SCLK,
+	GPIO26_SSP2_FRM,
+	GPIO27_SSP2_TXD,
+	GPIO29_SSP2_EXTCLK,
+
+	/* LEDs */
+	GPIO35_GPIO | MFP_LPM_PULL_LOW,
+	GPIO36_GPIO | MFP_LPM_DRIVE_HIGH,
+};
+
+static mfp_cfg_t raumfeld_speaker_pin_config[] __initdata = {
+	/* UART1 */
+	GPIO77_UART1_RXD,
+	GPIO78_UART1_TXD,
+	GPIO79_UART1_CTS,
+	GPIO81_UART1_DSR,
+	GPIO83_UART1_DTR,
+	GPIO84_UART1_RTS,
+
+	/* UART3 */
+	GPIO110_UART3_RXD,
+
+	/* USB Host */
+	GPIO0_2_USBH_PEN,
+	GPIO1_2_USBH_PWR,
+
+	/* I2C */
+	GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
+	GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
+
+	/* SPI */
+	GPIO34_GPIO,	/* SPDIF_CS */
+	GPIO96_GPIO,	/* MCLK_CS */
+	GPIO125_GPIO,	/* ACCEL_CS */
+
+	/* MMC */
+	GPIO3_MMC1_DAT0,
+	GPIO4_MMC1_DAT1,
+	GPIO5_MMC1_DAT2,
+	GPIO6_MMC1_DAT3,
+	GPIO7_MMC1_CLK,
+	GPIO8_MMC1_CMD,
+
+	/* Ethernet */
+	GPIO1_nCS2,			/* CS */
+	GPIO40_GPIO | MFP_PULL_HIGH,	/* IRQ */
+
+	/* SSP for I2S */
+	GPIO85_SSP1_SCLK,
+	GPIO89_SSP1_EXTCLK,
+	GPIO86_SSP1_FRM,
+	GPIO87_SSP1_TXD,
+	GPIO88_SSP1_RXD,
+	GPIO90_SSP1_SYSCLK,
+
+	/* LEDs */
+	GPIO35_GPIO | MFP_LPM_PULL_LOW,
+	GPIO36_GPIO | MFP_LPM_DRIVE_HIGH,
+};
+
+/*
+ * SMSC LAN9220 Ethernet
+ */
+
+static struct resource smc91x_resources[] = {
+	{
+		.start	= PXA3xx_CS2_PHYS,
+		.end	= PXA3xx_CS2_PHYS + 0xfffff,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= gpio_to_irq(GPIO_ETH_IRQ),
+		.end	= gpio_to_irq(GPIO_ETH_IRQ),
+		.flags	= IORESOURCE_IRQ | IRQF_TRIGGER_FALLING,
+	}
+};
+
+static struct smsc911x_platform_config raumfeld_smsc911x_config = {
+	.phy_interface	= PHY_INTERFACE_MODE_MII,
+	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
+};
+
+static struct platform_device smc91x_device = {
+	.name		= "smsc911x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(smc91x_resources),
+	.resource	= smc91x_resources,
+	.dev		= {
+		.platform_data = &raumfeld_smsc911x_config,
+	}
+};
+
+/**
+ * NAND
+ */
+
+static struct mtd_partition raumfeld_nand_partitions[] = {
+	{
+		.name		= "Bootloader",
+		.offset		= 0,
+		.size		= 0xa0000,
+		.mask_flags	= MTD_WRITEABLE, /* force read-only */
+	},
+	{
+		.name		= "BootloaderEnvironment",
+		.offset		= 0xa0000,
+		.size		= 0x20000,
+	},
+	{
+		.name		= "BootloaderSplashScreen",
+		.offset		= 0xc0000,
+		.size		= 0x60000,
+	},
+	{
+		.name		= "UBI",
+		.offset		= 0x120000,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct pxa3xx_nand_platform_data raumfeld_nand_info = {
+	.enable_arbiter	= 1,
+	.keep_config	= 1,
+	.parts		= raumfeld_nand_partitions,
+	.nr_parts	= ARRAY_SIZE(raumfeld_nand_partitions),
+};
+
+/**
+ * USB (OHCI) support
+ */
+
+static struct pxaohci_platform_data raumfeld_ohci_info = {
+	.port_mode      = PMM_GLOBAL_MODE,
+	.flags		= ENABLE_PORT1,
+};
+
+/**
+ * Rotary encoder input device
+ */
+
+static struct rotary_encoder_platform_data raumfeld_rotary_encoder_info = {
+	.steps		= 24,
+	.axis		= REL_X,
+	.relative_axis	= 1,
+	.gpio_a		= GPIO_VOLENC_A,
+	.gpio_b		= GPIO_VOLENC_B,
+	.inverted_a	= 1,
+	.inverted_b	= 0,
+};
+
+static struct platform_device rotary_encoder_device = {
+	.name		= "rotary-encoder",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &raumfeld_rotary_encoder_info,
+	}
+};
+
+/**
+ * GPIO buttons
+ */
+
+static struct gpio_keys_button gpio_keys_button[] = {
+	{
+		.code			= KEY_F1,
+		.type			= EV_KEY,
+		.gpio			= GPIO_KEY1,
+		.active_low		= 1,
+		.wakeup			= 0,
+		.debounce_interval	= 5, /* ms */
+		.desc			= "Button 1",
+	},
+	{
+		.code			= KEY_F2,
+		.type			= EV_KEY,
+		.gpio			= GPIO_KEY2,
+		.active_low		= 1,
+		.wakeup			= 0,
+		.debounce_interval	= 5, /* ms */
+		.desc			= "Button 2",
+	},
+	{
+		.code			= KEY_F3,
+		.type			= EV_KEY,
+		.gpio			= GPIO_KEY3,
+		.active_low		= 1,
+		.wakeup			= 0,
+		.debounce_interval	= 5, /* ms */
+		.desc			= "Button 3",
+	},
+	{
+		.code			= KEY_F4,
+		.type			= EV_KEY,
+		.gpio			= GPIO_RESCUE_BOOT,
+		.active_low		= 0,
+		.wakeup			= 0,
+		.debounce_interval	= 5, /* ms */
+		.desc			= "rescue boot button",
+	},
+	{
+		.code			= KEY_F5,
+		.type			= EV_KEY,
+		.gpio			= GPIO_DOCK_DETECT,
+		.active_low		= 1,
+		.wakeup			= 0,
+		.debounce_interval	= 5, /* ms */
+		.desc			= "dock detect",
+	},
+	{
+		.code			= KEY_F6,
+		.type			= EV_KEY,
+		.gpio			= GPIO_ON_OFF,
+		.active_low		= 0,
+		.wakeup			= 0,
+		.debounce_interval	= 5, /* ms */
+		.desc			= "on/off button",
+	},
+};
+
+static struct gpio_keys_platform_data gpio_keys_platform_data = {
+	.buttons	= gpio_keys_button,
+	.nbuttons	= ARRAY_SIZE(gpio_keys_button),
+	.rep		= 0,
+};
+
+static struct platform_device raumfeld_gpio_keys_device = {
+	.name	= "gpio-keys",
+	.id	= -1,
+	.dev 	= {
+		.platform_data	= &gpio_keys_platform_data,
+	}
+};
+
+/**
+ * GPIO LEDs
+ */
+
+static struct gpio_led raumfeld_leds[] = {
+	{
+		.name		= "raumfeld:1",
+		.gpio		= GPIO_LED1,
+		.active_low	= 1,
+		.default_state	= LEDS_GPIO_DEFSTATE_ON,
+	},
+	{
+		.name		= "raumfeld:2",
+		.gpio		= GPIO_LED2,
+		.active_low	= 0,
+		.default_state	= LEDS_GPIO_DEFSTATE_OFF,
+	}
+};
+
+static struct gpio_led_platform_data raumfeld_led_platform_data = {
+	.leds		= raumfeld_leds,
+	.num_leds	= ARRAY_SIZE(raumfeld_leds),
+};
+
+static struct platform_device raumfeld_led_device = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &raumfeld_led_platform_data,
+	},
+};
+
+/**
+ * One-wire (W1 bus) support
+ */
+
+static void w1_enable_external_pullup(int enable)
+{
+	gpio_set_value(GPIO_W1_PULLUP_ENABLE, enable);
+	msleep(100);
+}
+
+static struct w1_gpio_platform_data w1_gpio_platform_data = {
+	.pin			= GPIO_ONE_WIRE,
+	.is_open_drain		= 0,
+	.enable_external_pullup	= w1_enable_external_pullup,
+};
+
+struct platform_device raumfeld_w1_gpio_device = {
+	.name	= "w1-gpio",
+	.dev	= {
+		.platform_data = &w1_gpio_platform_data
+	}
+};
+
+static void __init raumfeld_w1_init(void)
+{
+	int ret = gpio_request(GPIO_W1_PULLUP_ENABLE,
+				"W1 external pullup enable");
+
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_W1_PULLUP_ENABLE\n");
+	else
+		gpio_direction_output(GPIO_W1_PULLUP_ENABLE, 0);
+
+	platform_device_register(&raumfeld_w1_gpio_device);
+}
+
+/**
+ * Framebuffer device
+ */
+
+/* PWM controlled backlight */
+static struct platform_pwm_backlight_data raumfeld_pwm_backlight_data = {
+	.pwm_id		= 0,
+	.max_brightness	= 100,
+	.dft_brightness	= 100,
+	/* 10000 ns = 10 ms ^= 100 kHz */
+	.pwm_period_ns	= 10000,
+};
+
+static struct platform_device raumfeld_pwm_backlight_device = {
+	.name	= "pwm-backlight",
+	.dev	= {
+		.parent		= &pxa27x_device_pwm0.dev,
+		.platform_data	= &raumfeld_pwm_backlight_data,
+	}
+};
+
+/* LT3593 controlled backlight */
+static struct gpio_led raumfeld_lt3593_led = {
+	.name		= "backlight",
+	.gpio		= mfp_to_gpio(MFP_PIN_GPIO17),
+	.default_state	= LEDS_GPIO_DEFSTATE_ON,
+};
+
+static struct gpio_led_platform_data raumfeld_lt3593_platform_data = {
+	.leds		= &raumfeld_lt3593_led,
+	.num_leds	= 1,
+};
+
+static struct platform_device raumfeld_lt3593_device = {
+	.name	= "leds-lt3593",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &raumfeld_lt3593_platform_data,
+	},
+};
+
+static struct pxafb_mode_info sharp_lq043t3dx02_mode = {
+	.pixclock	= 111000,
+	.xres		= 480,
+	.yres		= 272,
+	.bpp		= 16,
+	.hsync_len	= 4,
+	.left_margin	= 2,
+	.right_margin	= 1,
+	.vsync_len	= 1,
+	.upper_margin	= 3,
+	.lower_margin	= 1,
+	.sync		= 0,
+};
+
+static struct pxafb_mach_info raumfeld_sharp_lcd_info = {
+	.modes		= &sharp_lq043t3dx02_mode,
+	.num_modes	= 1,
+	.video_mem_size = 0x400000,
+	.lcd_conn	= LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+};
+
+static void __init raumfeld_lcd_init(void)
+{
+	int ret;
+
+	set_pxa_fb_info(&raumfeld_sharp_lcd_info);
+
+	/* Earlier devices had the backlight regulator controlled
+	 * via PWM, later versions use another controller for that */
+	if ((system_rev & 0xff) < 2) {
+		mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT;
+		pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1);
+		platform_device_register(&raumfeld_pwm_backlight_device);
+	} else
+		platform_device_register(&raumfeld_lt3593_device);
+
+	ret = gpio_request(GPIO_TFT_VA_EN, "display VA enable");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_TFT_VA_EN\n");
+	else
+		gpio_direction_output(GPIO_TFT_VA_EN, 1);
+
+	ret = gpio_request(GPIO_DISPLAY_ENABLE, "display enable");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_DISPLAY_ENABLE\n");
+	else
+		gpio_direction_output(GPIO_DISPLAY_ENABLE, 1);
+}
+
+/**
+ * SPI devices
+ */
+
+struct spi_gpio_platform_data raumfeld_spi_platform_data = {
+	.sck		= GPIO_SPI_CLK,
+	.mosi		= GPIO_SPI_MOSI,
+	.miso		= GPIO_SPI_MISO,
+	.num_chipselect	= 3,
+};
+
+static struct platform_device raumfeld_spi_device = {
+	.name	= "spi_gpio",
+	.id	= 0,
+	.dev 	= {
+		.platform_data	= &raumfeld_spi_platform_data,
+	}
+};
+
+static struct lis3lv02d_platform_data lis3_pdata = {
+	.click_flags 	= LIS3_CLICK_SINGLE_X |
+			  LIS3_CLICK_SINGLE_Y |
+			  LIS3_CLICK_SINGLE_Z,
+	.irq_cfg	= LIS3_IRQ1_CLICK | LIS3_IRQ2_CLICK,
+	.wakeup_flags	= LIS3_WAKEUP_X_LO | LIS3_WAKEUP_X_HI |
+			  LIS3_WAKEUP_Y_LO | LIS3_WAKEUP_Y_HI |
+			  LIS3_WAKEUP_Z_LO | LIS3_WAKEUP_Z_HI,
+	.wakeup_thresh	= 10,
+	.click_thresh_x = 10,
+	.click_thresh_y = 10,
+	.click_thresh_z = 10,
+};
+
+#define SPI_AK4104	\
+{			\
+	.modalias	= "ak4104",	\
+	.max_speed_hz	= 10000,	\
+	.bus_num	= 0,		\
+	.chip_select	= 0,		\
+	.controller_data = (void *) GPIO_SPDIF_CS,	\
+}
+
+#define SPI_LIS3	\
+{			\
+	.modalias	= "lis3lv02d_spi",	\
+	.max_speed_hz	= 1000000,		\
+	.bus_num	= 0,			\
+	.chip_select	= 1,			\
+	.controller_data = (void *) GPIO_ACCEL_CS,	\
+	.platform_data	= &lis3_pdata,		\
+	.irq		= gpio_to_irq(GPIO_ACCEL_IRQ),	\
+}
+
+#define SPI_DAC7512	\
+{	\
+	.modalias	= "dac7512",		\
+	.max_speed_hz	= 1000000,		\
+	.bus_num	= 0,			\
+	.chip_select	= 2,			\
+	.controller_data = (void *) GPIO_MCLK_DAC_CS,	\
+}
+
+static struct spi_board_info connector_spi_devices[] __initdata = {
+	SPI_AK4104,
+	SPI_DAC7512,
+};
+
+static struct spi_board_info speaker_spi_devices[] __initdata = {
+	SPI_DAC7512,
+};
+
+static struct spi_board_info controller_spi_devices[] __initdata = {
+	SPI_LIS3,
+};
+
+/**
+ * MMC for Marvell Libertas 8688 via SDIO
+ */
+
+static int raumfeld_mci_init(struct device *dev, irq_handler_t isr, void *data)
+{
+	gpio_set_value(GPIO_W2W_RESET, 1);
+	gpio_set_value(GPIO_W2W_PDN, 1);
+
+	return 0;
+}
+
+static void raumfeld_mci_exit(struct device *dev, void *data)
+{
+	gpio_set_value(GPIO_W2W_RESET, 0);
+	gpio_set_value(GPIO_W2W_PDN, 0);
+}
+
+static struct pxamci_platform_data raumfeld_mci_platform_data = {
+	.init			= raumfeld_mci_init,
+	.exit			= raumfeld_mci_exit,
+	.detect_delay		= 20,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
+};
+
+/*
+ * External power / charge logic
+ */
+
+static int power_supply_init(struct device *dev)
+{
+	return 0;
+}
+
+static void power_supply_exit(struct device *dev)
+{
+}
+
+static int raumfeld_is_ac_online(void)
+{
+	return !gpio_get_value(GPIO_CHARGE_DC_OK);
+}
+
+static int raumfeld_is_usb_online(void)
+{
+	return 0;
+}
+
+static char *raumfeld_power_supplicants[] = { "ds2760-battery.0" };
+
+static struct pda_power_pdata power_supply_info = {
+	.init			= power_supply_init,
+	.is_ac_online		= raumfeld_is_ac_online,
+	.is_usb_online		= raumfeld_is_usb_online,
+	.exit			= power_supply_exit,
+	.supplied_to		= raumfeld_power_supplicants,
+	.num_supplicants	= ARRAY_SIZE(raumfeld_power_supplicants)
+};
+
+static struct resource power_supply_resources[] = {
+	{
+		.name  = "ac",
+		.flags = IORESOURCE_IRQ |
+			 IORESOURCE_IRQ_HIGHEDGE | IORESOURCE_IRQ_LOWEDGE,
+		.start = GPIO_CHARGE_DC_OK,
+		.end   = GPIO_CHARGE_DC_OK,
+	},
+};
+
+static irqreturn_t charge_done_irq(int irq, void *dev_id)
+{
+	struct power_supply *psy;
+
+	psy = power_supply_get_by_name("ds2760-battery.0");
+
+	if (psy)
+		power_supply_set_battery_charged(psy);
+
+	return IRQ_HANDLED;
+}
+
+static struct platform_device raumfeld_power_supply = {
+	.name = "pda-power",
+	.id   = -1,
+	.dev  = {
+		.platform_data = &power_supply_info,
+	},
+	.resource      = power_supply_resources,
+	.num_resources = ARRAY_SIZE(power_supply_resources),
+};
+
+static void __init raumfeld_power_init(void)
+{
+	int ret;
+
+	/* Set PEN2 high to enable maximum charge current */
+	ret = gpio_request(GPIO_CHRG_PEN2, "CHRG_PEN2");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_CHRG_PEN2\n");
+	else
+		gpio_direction_output(GPIO_CHRG_PEN2, 1);
+
+	ret = gpio_request(GPIO_CHARGE_DC_OK, "CABLE_DC_OK");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_CHARGE_DC_OK\n");
+
+	ret = gpio_request(GPIO_CHARGE_USB_SUSP, "CHARGE_USB_SUSP");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_CHARGE_USB_SUSP\n");
+	else
+		gpio_direction_output(GPIO_CHARGE_USB_SUSP, 0);
+
+	power_supply_resources[0].start = gpio_to_irq(GPIO_CHARGE_DC_OK);
+	power_supply_resources[0].end = gpio_to_irq(GPIO_CHARGE_DC_OK);
+
+	ret = request_irq(gpio_to_irq(GPIO_CHARGE_DONE),
+			&charge_done_irq, IORESOURCE_IRQ_LOWEDGE,
+			"charge_done", NULL);
+
+	if (ret < 0)
+		printk(KERN_ERR "%s: unable to register irq %d\n", __func__,
+			GPIO_CHARGE_DONE);
+	else
+		platform_device_register(&raumfeld_power_supply);
+}
+
+/* Fixed regulator for AUDIO_VA, 0-0048 maps to the cs4270 codec device */
+
+static struct regulator_consumer_supply audio_va_consumer_supply =
+	REGULATOR_SUPPLY("va", "0-0048");
+
+struct regulator_init_data audio_va_initdata = {
+	.consumer_supplies = &audio_va_consumer_supply,
+	.num_consumer_supplies = 1,
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct fixed_voltage_config audio_va_config = {
+	.supply_name		= "audio_va",
+	.microvolts		= 5000000,
+	.gpio			= GPIO_AUDIO_VA_ENABLE,
+	.enable_high		= 1,
+	.enabled_at_boot	= 0,
+	.init_data		= &audio_va_initdata,
+};
+
+static struct platform_device audio_va_device = {
+	.name	= "reg-fixed-voltage",
+	.id	= 0,
+	.dev	= {
+		.platform_data = &audio_va_config,
+	},
+};
+
+/* Dummy supplies for Codec's VD/VLC */
+
+static struct regulator_consumer_supply audio_dummy_supplies[] = {
+	REGULATOR_SUPPLY("vd", "0-0048"),
+	REGULATOR_SUPPLY("vlc", "0-0048"),
+};
+
+struct regulator_init_data audio_dummy_initdata = {
+	.consumer_supplies = audio_dummy_supplies,
+	.num_consumer_supplies = ARRAY_SIZE(audio_dummy_supplies),
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct fixed_voltage_config audio_dummy_config = {
+	.supply_name		= "audio_vd",
+	.microvolts		= 3300000,
+	.gpio			= -1,
+	.init_data		= &audio_dummy_initdata,
+};
+
+static struct platform_device audio_supply_dummy_device = {
+	.name	= "reg-fixed-voltage",
+	.id	= 1,
+	.dev	= {
+		.platform_data = &audio_dummy_config,
+	},
+};
+
+static struct platform_device *audio_regulator_devices[] = {
+	&audio_va_device,
+	&audio_supply_dummy_device,
+};
+
+/**
+ * Regulator support via MAX8660
+ */
+
+static struct regulator_consumer_supply vcc_mmc_supply =
+	REGULATOR_SUPPLY("vmmc", "pxa2xx-mci.0");
+
+static struct regulator_init_data vcc_mmc_init_data = {
+	.constraints = {
+		.min_uV			= 3300000,
+		.max_uV			= 3300000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_STATUS |
+					  REGULATOR_CHANGE_VOLTAGE |
+					  REGULATOR_CHANGE_MODE,
+	},
+	.consumer_supplies = &vcc_mmc_supply,
+	.num_consumer_supplies = 1,
+};
+
+struct max8660_subdev_data max8660_v6_subdev_data = {
+	.id		= MAX8660_V6,
+	.name		= "vmmc",
+	.platform_data	= &vcc_mmc_init_data,
+};
+
+static struct max8660_platform_data max8660_pdata = {
+	.subdevs = &max8660_v6_subdev_data,
+	.num_subdevs = 1,
+};
+
+/**
+ * I2C devices
+ */
+
+static struct i2c_board_info raumfeld_pwri2c_board_info = {
+	.type		= "max8660",
+	.addr		= 0x34,
+	.platform_data	= &max8660_pdata,
+};
+
+static struct i2c_board_info raumfeld_connector_i2c_board_info __initdata = {
+	.type	= "cs4270",
+	.addr	= 0x48,
+};
+
+static struct eeti_ts_platform_data eeti_ts_pdata = {
+	.irq_active_high = 1,
+};
+
+static struct i2c_board_info raumfeld_controller_i2c_board_info __initdata = {
+	.type	= "eeti_ts",
+	.addr	= 0x0a,
+	.irq	= gpio_to_irq(GPIO_TOUCH_IRQ),
+	.platform_data = &eeti_ts_pdata,
+};
+
+static struct platform_device *raumfeld_common_devices[] = {
+	&raumfeld_gpio_keys_device,
+	&raumfeld_led_device,
+	&raumfeld_spi_device,
+};
+
+static void __init raumfeld_audio_init(void)
+{
+	int ret;
+
+	ret = gpio_request(GPIO_CODEC_RESET, "cs4270 reset");
+	if (ret < 0)
+		pr_warning("unable to request GPIO_CODEC_RESET\n");
+	else
+		gpio_direction_output(GPIO_CODEC_RESET, 1);
+
+	ret = gpio_request(GPIO_SPDIF_RESET, "ak4104 s/pdif reset");
+	if (ret < 0)
+		pr_warning("unable to request GPIO_SPDIF_RESET\n");
+	else
+		gpio_direction_output(GPIO_SPDIF_RESET, 1);
+
+	ret = gpio_request(GPIO_MCLK_RESET, "MCLK reset");
+	if (ret < 0)
+		pr_warning("unable to request GPIO_MCLK_RESET\n");
+	else
+		gpio_direction_output(GPIO_MCLK_RESET, 1);
+
+	platform_add_devices(ARRAY_AND_SIZE(audio_regulator_devices));
+}
+
+static void __init raumfeld_common_init(void)
+{
+	int ret;
+
+	/* The on/off button polarity has changed after revision 1 */
+	if ((system_rev & 0xff) > 1) {
+		int i;
+
+		for (i = 0; i < ARRAY_SIZE(gpio_keys_button); i++)
+			if (!strcmp(gpio_keys_button[i].desc, "on/off button"))
+				gpio_keys_button[i].active_low = 1;
+	}
+
+	enable_irq_wake(IRQ_WAKEUP0);
+
+	pxa3xx_set_nand_info(&raumfeld_nand_info);
+	pxa3xx_set_i2c_power_info(NULL);
+	pxa_set_ohci_info(&raumfeld_ohci_info);
+	pxa_set_mci_info(&raumfeld_mci_platform_data);
+	pxa_set_i2c_info(NULL);
+	pxa_set_ffuart_info(NULL);
+
+	ret = gpio_request(GPIO_W2W_RESET, "Wi2Wi reset");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_W2W_RESET\n");
+	else
+		gpio_direction_output(GPIO_W2W_RESET, 0);
+
+	ret = gpio_request(GPIO_W2W_PDN, "Wi2Wi powerup");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_W2W_PDN\n");
+	else
+		gpio_direction_output(GPIO_W2W_PDN, 0);
+
+	/* this can be used to switch off the device */
+	ret = gpio_request(GPIO_SHUTDOWN_SUPPLY,
+				"supply shutdown");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_SHUTDOWN_SUPPLY\n");
+	else
+		gpio_direction_output(GPIO_SHUTDOWN_SUPPLY, 0);
+
+	platform_add_devices(ARRAY_AND_SIZE(raumfeld_common_devices));
+	i2c_register_board_info(1, &raumfeld_pwri2c_board_info, 1);
+}
+
+static void __init raumfeld_controller_init(void)
+{
+	int ret;
+
+	pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_controller_pin_config));
+	platform_device_register(&rotary_encoder_device);
+	spi_register_board_info(ARRAY_AND_SIZE(controller_spi_devices));
+	i2c_register_board_info(0, &raumfeld_controller_i2c_board_info, 1);
+
+	ret = gpio_request(GPIO_SHUTDOWN_BATT, "battery shutdown");
+	if (ret < 0)
+		pr_warning("Unable to request GPIO_SHUTDOWN_BATT\n");
+	else
+		gpio_direction_output(GPIO_SHUTDOWN_BATT, 0);
+
+	raumfeld_common_init();
+	raumfeld_power_init();
+	raumfeld_lcd_init();
+	raumfeld_w1_init();
+}
+
+static void __init raumfeld_connector_init(void)
+{
+	pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_connector_pin_config));
+	spi_register_board_info(ARRAY_AND_SIZE(connector_spi_devices));
+	i2c_register_board_info(0, &raumfeld_connector_i2c_board_info, 1);
+
+	platform_device_register(&smc91x_device);
+
+	raumfeld_audio_init();
+	raumfeld_common_init();
+}
+
+static void __init raumfeld_speaker_init(void)
+{
+	pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_speaker_pin_config));
+	spi_register_board_info(ARRAY_AND_SIZE(speaker_spi_devices));
+	i2c_register_board_info(0, &raumfeld_connector_i2c_board_info, 1);
+
+	platform_device_register(&smc91x_device);
+	platform_device_register(&rotary_encoder_device);
+
+	raumfeld_audio_init();
+	raumfeld_common_init();
+}
+
+/* physical memory regions */
+#define	RAUMFELD_SDRAM_BASE	0xa0000000	/* SDRAM region */
+
+#ifdef CONFIG_MACH_RAUMFELD_RC
+MACHINE_START(RAUMFELD_RC, "Raumfeld Controller")
+	.phys_io	= 0x40000000,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.boot_params	= RAUMFELD_SDRAM_BASE + 0x100,
+	.init_machine	= raumfeld_controller_init,
+	.map_io		= pxa_map_io,
+	.init_irq	= pxa3xx_init_irq,
+	.timer		= &pxa_timer,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_RAUMFELD_CONNECTOR
+MACHINE_START(RAUMFELD_CONNECTOR, "Raumfeld Connector")
+	.phys_io	= 0x40000000,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.boot_params	= RAUMFELD_SDRAM_BASE + 0x100,
+	.init_machine	= raumfeld_connector_init,
+	.map_io		= pxa_map_io,
+	.init_irq	= pxa3xx_init_irq,
+	.timer		= &pxa_timer,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_RAUMFELD_SPEAKER
+MACHINE_START(RAUMFELD_SPEAKER, "Raumfeld Speaker")
+	.phys_io	= 0x40000000,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.boot_params	= RAUMFELD_SDRAM_BASE + 0x100,
+	.init_machine	= raumfeld_speaker_init,
+	.map_io		= pxa_map_io,
+	.init_irq	= pxa3xx_init_irq,
+	.timer		= &pxa_timer,
+MACHINE_END
+#endif
diff --git a/arch/arm/mach-pxa/sharpsl_pm.c b/arch/arm/mach-pxa/sharpsl_pm.c
index 67229a1ef55..463d874bb86 100644
--- a/arch/arm/mach-pxa/sharpsl_pm.c
+++ b/arch/arm/mach-pxa/sharpsl_pm.c
@@ -900,7 +900,7 @@ static struct platform_suspend_ops sharpsl_pm_ops = {
 };
 #endif
 
-static int __init sharpsl_pm_probe(struct platform_device *pdev)
+static int __devinit sharpsl_pm_probe(struct platform_device *pdev)
 {
 	int ret;
 
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 28352c0b8c3..19b5109d980 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -56,25 +56,7 @@ static unsigned long spitz_pin_config[] __initdata = {
 	GPIO80_nCS_4,	/* SCOOP #1 */
 
 	/* LCD - 16bpp Active TFT */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* PC Card */
 	GPIO48_nPOE,
diff --git a/arch/arm/mach-pxa/ssp.c b/arch/arm/mach-pxa/ssp.c
index 9ebe658590f..a81d6dbf662 100644
--- a/arch/arm/mach-pxa/ssp.c
+++ b/arch/arm/mach-pxa/ssp.c
@@ -35,6 +35,8 @@
 #include <mach/ssp.h>
 #include <mach/regs-ssp.h>
 
+#ifdef CONFIG_PXA_SSP_LEGACY
+
 #define TIMEOUT 100000
 
 static irqreturn_t ssp_interrupt(int irq, void *dev_id)
@@ -303,6 +305,7 @@ void ssp_exit(struct ssp_dev *dev)
 	clk_disable(ssp->clk);
 	ssp_free(ssp);
 }
+#endif /* CONFIG_PXA_SSP_LEGACY */
 
 static DEFINE_MUTEX(ssp_lock);
 static LIST_HEAD(ssp_list);
@@ -488,6 +491,7 @@ static void __exit pxa_ssp_exit(void)
 arch_initcall(pxa_ssp_init);
 module_exit(pxa_ssp_exit);
 
+#ifdef CONFIG_PXA_SSP_LEGACY
 EXPORT_SYMBOL(ssp_write_word);
 EXPORT_SYMBOL(ssp_read_word);
 EXPORT_SYMBOL(ssp_flush);
@@ -498,6 +502,7 @@ EXPORT_SYMBOL(ssp_restore_state);
 EXPORT_SYMBOL(ssp_init);
 EXPORT_SYMBOL(ssp_exit);
 EXPORT_SYMBOL(ssp_config);
+#endif
 
 MODULE_DESCRIPTION("PXA SSP driver");
 MODULE_AUTHOR("Liam Girdwood");
diff --git a/arch/arm/mach-pxa/time.c b/arch/arm/mach-pxa/time.c
index 750c448db67..293e40aeaf2 100644
--- a/arch/arm/mach-pxa/time.c
+++ b/arch/arm/mach-pxa/time.c
@@ -76,14 +76,12 @@ pxa_ost0_interrupt(int irq, void *dev_id)
 static int
 pxa_osmr0_set_next_event(unsigned long delta, struct clock_event_device *dev)
 {
-	unsigned long flags, next, oscr;
+	unsigned long next, oscr;
 
-	raw_local_irq_save(flags);
 	OIER |= OIER_E0;
 	next = OSCR + delta;
 	OSMR0 = next;
 	oscr = OSCR;
-	raw_local_irq_restore(flags);
 
 	return (signed)(next - oscr) <= MIN_OSCR_DELTA ? -ETIME : 0;
 }
@@ -91,23 +89,17 @@ pxa_osmr0_set_next_event(unsigned long delta, struct clock_event_device *dev)
 static void
 pxa_osmr0_set_mode(enum clock_event_mode mode, struct clock_event_device *dev)
 {
-	unsigned long irqflags;
-
 	switch (mode) {
 	case CLOCK_EVT_MODE_ONESHOT:
-		raw_local_irq_save(irqflags);
 		OIER &= ~OIER_E0;
 		OSSR = OSSR_M0;
-		raw_local_irq_restore(irqflags);
 		break;
 
 	case CLOCK_EVT_MODE_UNUSED:
 	case CLOCK_EVT_MODE_SHUTDOWN:
 		/* initializing, released, or preparing for suspend */
-		raw_local_irq_save(irqflags);
 		OIER &= ~OIER_E0;
 		OSSR = OSSR_M0;
-		raw_local_irq_restore(irqflags);
 		break;
 
 	case CLOCK_EVT_MODE_RESUME:
diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c
index c854c168a45..ad552791c4c 100644
--- a/arch/arm/mach-pxa/tosa.c
+++ b/arch/arm/mach-pxa/tosa.c
@@ -32,6 +32,7 @@
 #include <linux/gpio.h>
 #include <linux/pda_power.h>
 #include <linux/spi/spi.h>
+#include <linux/input/matrix_keypad.h>
 
 #include <asm/setup.h>
 #include <asm/mach-types.h>
@@ -131,24 +132,24 @@ static unsigned long tosa_pin_config[] = {
 	GPIO45_BTUART_RTS,
 
 	/* Keybd */
-	GPIO58_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO59_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO60_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO61_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO62_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO63_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO64_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO65_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO66_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO67_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO68_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO69_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO70_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO71_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO72_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO73_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO74_GPIO | MFP_LPM_DRIVE_LOW,
-	GPIO75_GPIO | MFP_LPM_DRIVE_LOW,
+	GPIO58_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 0 */
+	GPIO59_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 1 */
+	GPIO60_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 2 */
+	GPIO61_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 3 */
+	GPIO62_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 4 */
+	GPIO63_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 5 */
+	GPIO64_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 6 */
+	GPIO65_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 7 */
+	GPIO66_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 8 */
+	GPIO67_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 9 */
+	GPIO68_GPIO | MFP_LPM_DRIVE_LOW,	/* Column 10 */
+	GPIO69_GPIO | MFP_LPM_DRIVE_LOW,	/* Row 0 */
+	GPIO70_GPIO | MFP_LPM_DRIVE_LOW,	/* Row 1 */
+	GPIO71_GPIO | MFP_LPM_DRIVE_LOW,	/* Row 2 */
+	GPIO72_GPIO | MFP_LPM_DRIVE_LOW,	/* Row 3 */
+	GPIO73_GPIO | MFP_LPM_DRIVE_LOW,	/* Row 4 */
+	GPIO74_GPIO | MFP_LPM_DRIVE_LOW,	/* Row 5 */
+	GPIO75_GPIO | MFP_LPM_DRIVE_LOW,	/* Row 6 */
 
 	/* SPI */
 	GPIO81_SSP2_CLK_OUT,
@@ -411,9 +412,87 @@ static struct platform_device tosa_power_device = {
 /*
  * Tosa Keyboard
  */
+static const uint32_t tosakbd_keymap[] = {
+	KEY(0, 2, KEY_W),
+	KEY(0, 6, KEY_K),
+	KEY(0, 7, KEY_BACKSPACE),
+	KEY(0, 8, KEY_P),
+	KEY(1, 1, KEY_Q),
+	KEY(1, 2, KEY_E),
+	KEY(1, 3, KEY_T),
+	KEY(1, 4, KEY_Y),
+	KEY(1, 6, KEY_O),
+	KEY(1, 7, KEY_I),
+	KEY(1, 8, KEY_COMMA),
+	KEY(2, 1, KEY_A),
+	KEY(2, 2, KEY_D),
+	KEY(2, 3, KEY_G),
+	KEY(2, 4, KEY_U),
+	KEY(2, 6, KEY_L),
+	KEY(2, 7, KEY_ENTER),
+	KEY(2, 8, KEY_DOT),
+	KEY(3, 1, KEY_Z),
+	KEY(3, 2, KEY_C),
+	KEY(3, 3, KEY_V),
+	KEY(3, 4, KEY_J),
+	KEY(3, 5, TOSA_KEY_ADDRESSBOOK),
+	KEY(3, 6, TOSA_KEY_CANCEL),
+	KEY(3, 7, TOSA_KEY_CENTER),
+	KEY(3, 8, TOSA_KEY_OK),
+	KEY(3, 9, KEY_LEFTSHIFT),
+	KEY(4, 1, KEY_S),
+	KEY(4, 2, KEY_R),
+	KEY(4, 3, KEY_B),
+	KEY(4, 4, KEY_N),
+	KEY(4, 5, TOSA_KEY_CALENDAR),
+	KEY(4, 6, TOSA_KEY_HOMEPAGE),
+	KEY(4, 7, KEY_LEFTCTRL),
+	KEY(4, 8, TOSA_KEY_LIGHT),
+	KEY(4, 10, KEY_RIGHTSHIFT),
+	KEY(5, 1, KEY_TAB),
+	KEY(5, 2, KEY_SLASH),
+	KEY(5, 3, KEY_H),
+	KEY(5, 4, KEY_M),
+	KEY(5, 5, TOSA_KEY_MENU),
+	KEY(5, 7, KEY_UP),
+	KEY(5, 11, TOSA_KEY_FN),
+	KEY(6, 1, KEY_X),
+	KEY(6, 2, KEY_F),
+	KEY(6, 3, KEY_SPACE),
+	KEY(6, 4, KEY_APOSTROPHE),
+	KEY(6, 5, TOSA_KEY_MAIL),
+	KEY(6, 6, KEY_LEFT),
+	KEY(6, 7, KEY_DOWN),
+	KEY(6, 8, KEY_RIGHT),
+};
+
+static struct matrix_keymap_data tosakbd_keymap_data = {
+	.keymap		= tosakbd_keymap,
+	.keymap_size	= ARRAY_SIZE(tosakbd_keymap),
+};
+
+static const int tosakbd_col_gpios[] =
+			{ 58, 59, 60, 61, 62, 63, 64, 65, 66, 67, 68 };
+static const int tosakbd_row_gpios[] =
+			{ 69, 70, 71, 72, 73, 74, 75 };
+
+static struct matrix_keypad_platform_data tosakbd_pdata = {
+	.keymap_data		= &tosakbd_keymap_data,
+	.row_gpios		= tosakbd_row_gpios,
+	.col_gpios		= tosakbd_col_gpios,
+	.num_row_gpios		= ARRAY_SIZE(tosakbd_row_gpios),
+	.num_col_gpios		= ARRAY_SIZE(tosakbd_col_gpios),
+	.col_scan_delay_us	= 10,
+	.debounce_ms		= 10,
+	.wakeup			= 1,
+};
+
 static struct platform_device tosakbd_device = {
-	.name		= "tosa-keyboard",
+	.name		= "matrix-keypad",
 	.id		= -1,
+	.dev		= {
+		.platform_data = &tosakbd_pdata,
+	},
 };
 
 static struct gpio_keys_button tosa_gpio_keys[] = {
diff --git a/arch/arm/mach-pxa/trizeps4.c b/arch/arm/mach-pxa/trizeps4.c
index 0aa858ebc57..797f2544d0c 100644
--- a/arch/arm/mach-pxa/trizeps4.c
+++ b/arch/arm/mach-pxa/trizeps4.c
@@ -72,27 +72,14 @@ static unsigned long trizeps4_pin_config[] __initdata = {
 	GPIO79_nCS_3,		/* Logic CS */
 	GPIO0_GPIO | WAKEUP_ON_EDGE_RISE,	/* Logic irq */
 
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+
 	/* LCD - 16bpp Active TFT */
-	GPIO58_LCD_LDD_0,
-	GPIO59_LCD_LDD_1,
-	GPIO60_LCD_LDD_2,
-	GPIO61_LCD_LDD_3,
-	GPIO62_LCD_LDD_4,
-	GPIO63_LCD_LDD_5,
-	GPIO64_LCD_LDD_6,
-	GPIO65_LCD_LDD_7,
-	GPIO66_LCD_LDD_8,
-	GPIO67_LCD_LDD_9,
-	GPIO68_LCD_LDD_10,
-	GPIO69_LCD_LDD_11,
-	GPIO70_LCD_LDD_12,
-	GPIO71_LCD_LDD_13,
-	GPIO72_LCD_LDD_14,
-	GPIO73_LCD_LDD_15,
-	GPIO74_LCD_FCLK,
-	GPIO75_LCD_LCLK,
-	GPIO76_LCD_PCLK,
-	GPIO77_LCD_BIAS,
+	GPIOxx_LCD_TFT_16BPP,
 
 	/* UART */
 	GPIO9_FFUART_CTS,
diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c
index 89f258c9e12..1dd13346f97 100644
--- a/arch/arm/mach-pxa/viper.c
+++ b/arch/arm/mach-pxa/viper.c
@@ -281,7 +281,7 @@ static void viper_irq_handler(unsigned int irq, struct irq_desc *desc)
 	do {
 		/* we're in a chained irq handler,
 		 * so ack the interrupt by hand */
-		GEDR(VIPER_CPLD_GPIO) = GPIO_bit(VIPER_CPLD_GPIO);
+		desc->chip->ack(irq);
 
 		if (likely(pending)) {
 			irq = viper_bit_to_irq(__ffs(pending));
@@ -711,6 +711,12 @@ static mfp_cfg_t viper_pin_config[] __initdata = {
 	GPIO80_nCS_4,
 	GPIO33_nCS_5,
 
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+
 	/* FP Backlight */
 	GPIO9_GPIO, 				/* VIPER_BCKLIGHT_EN_GPIO */
 	GPIO10_GPIO,				/* VIPER_LCD_EN_GPIO */
diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c
index 75f2a37f945..39896d88358 100644
--- a/arch/arm/mach-pxa/zeus.c
+++ b/arch/arm/mach-pxa/zeus.c
@@ -26,6 +26,7 @@
 #include <linux/i2c.h>
 #include <linux/i2c/pca953x.h>
 #include <linux/apm-emulation.h>
+#include <linux/can/platform/mcp251x.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -387,11 +388,47 @@ static struct pxa2xx_spi_master pxa2xx_spi_ssp3_master_info = {
 	.enable_dma     = 1,
 };
 
-static struct platform_device pxa2xx_spi_ssp3_device = {
-	.name = "pxa2xx-spi",
-	.id = 3,
-	.dev = {
-		.platform_data = &pxa2xx_spi_ssp3_master_info,
+/* CAN bus on SPI */
+static int zeus_mcp2515_setup(struct spi_device *sdev)
+{
+	int err;
+
+	err = gpio_request(ZEUS_CAN_SHDN_GPIO, "CAN shutdown");
+	if (err)
+		return err;
+
+	err = gpio_direction_output(ZEUS_CAN_SHDN_GPIO, 1);
+	if (err) {
+		gpio_free(ZEUS_CAN_SHDN_GPIO);
+		return err;
+	}
+
+	return 0;
+}
+
+static int zeus_mcp2515_transceiver_enable(int enable)
+{
+	gpio_set_value(ZEUS_CAN_SHDN_GPIO, !enable);
+	return 0;
+}
+
+static struct mcp251x_platform_data zeus_mcp2515_pdata = {
+	.oscillator_frequency	= 16*1000*1000,
+	.model			= CAN_MCP251X_MCP2515,
+	.board_specific_setup	= zeus_mcp2515_setup,
+	.transceiver_enable	= zeus_mcp2515_transceiver_enable,
+	.power_enable		= zeus_mcp2515_transceiver_enable,
+};
+
+static struct spi_board_info zeus_spi_board_info[] = {
+	[0] = {
+		.modalias	= "mcp251x",
+		.platform_data	= &zeus_mcp2515_pdata,
+		.irq		= gpio_to_irq(ZEUS_CAN_GPIO),
+		.max_speed_hz	= 1*1000*1000,
+		.bus_num	= 3,
+		.mode		= SPI_MODE_0,
+		.chip_select	= 0,
 	},
 };
 
@@ -457,15 +494,28 @@ static struct platform_device zeus_pcmcia_device = {
 	},
 };
 
+static struct resource zeus_max6369_resource = {
+	.start		= ZEUS_CPLD_EXTWDOG_PHYS,
+	.end		= ZEUS_CPLD_EXTWDOG_PHYS,
+	.flags		= IORESOURCE_MEM,
+};
+
+struct platform_device zeus_max6369_device = {
+	.name		= "max6369_wdt",
+	.id		= -1,
+	.resource	= &zeus_max6369_resource,
+	.num_resources	= 1,
+};
+
 static struct platform_device *zeus_devices[] __initdata = {
 	&zeus_serial_device,
 	&zeus_mtd_devices[0],
 	&zeus_dm9k0_device,
 	&zeus_dm9k1_device,
 	&zeus_sram_device,
-	&pxa2xx_spi_ssp3_device,
 	&zeus_leds_device,
 	&zeus_pcmcia_device,
+	&zeus_max6369_device,
 };
 
 /* AC'97 */
@@ -509,7 +559,9 @@ static void zeus_ohci_exit(struct device *dev)
 
 static struct pxaohci_platform_data zeus_ohci_platform_data = {
 	.port_mode	= PMM_NPS_MODE,
-	.flags		= ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW,
+	/* Clear Power Control Polarity Low and set Power Sense
+	 * Polarity Low. Supply power to USB ports. */
+	.flags		= ENABLE_PORT_ALL | POWER_SENSE_LOW,
 	.init		= zeus_ohci_init,
 	.exit		= zeus_ohci_exit,
 };
@@ -621,11 +673,15 @@ static struct pxa2xx_udc_mach_info zeus_udc_info = {
 	.udc_command = zeus_udc_command,
 };
 
+#ifdef CONFIG_PM
 static void zeus_power_off(void)
 {
 	local_irq_disable();
 	pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP);
 }
+#else
+#define zeus_power_off   NULL
+#endif
 
 #ifdef CONFIG_APM_EMULATION
 static void zeus_get_power_status(struct apm_power_info *info)
@@ -706,6 +762,12 @@ static struct i2c_board_info __initdata zeus_i2c_devices[] = {
 };
 
 static mfp_cfg_t zeus_pin_config[] __initdata = {
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+
 	GPIO15_nCS_1,
 	GPIO78_nCS_2,
 	GPIO80_nCS_4,
@@ -731,6 +793,11 @@ static mfp_cfg_t zeus_pin_config[] __initdata = {
 	GPIO104_CIF_DD_2,
 	GPIO105_CIF_DD_1,
 
+	GPIO81_SSP3_TXD,
+	GPIO82_SSP3_RXD,
+	GPIO83_SSP3_SFRM,
+	GPIO84_SSP3_SCLK,
+
 	GPIO48_nPOE,
 	GPIO49_nPWE,
 	GPIO50_nPIOR,
@@ -785,6 +852,8 @@ static void __init zeus_init(void)
 	pxa_set_ac97_info(&zeus_ac97_info);
 	pxa_set_i2c_info(NULL);
 	i2c_register_board_info(0, ARRAY_AND_SIZE(zeus_i2c_devices));
+	pxa2xx_set_spi_info(3, &pxa2xx_spi_ssp3_master_info);
+	spi_register_board_info(zeus_spi_board_info, ARRAY_SIZE(zeus_spi_board_info));
 }
 
 static struct map_desc zeus_io_desc[] __initdata = {
@@ -807,12 +876,6 @@ static struct map_desc zeus_io_desc[] __initdata = {
 		.type    = MT_DEVICE,
 	},
 	{
-		.virtual = ZEUS_CPLD_EXTWDOG,
-		.pfn     = __phys_to_pfn(ZEUS_CPLD_EXTWDOG_PHYS),
-		.length  = 0x1000,
-		.type    = MT_DEVICE,
-	},
-	{
 		.virtual = ZEUS_PC104IO,
 		.pfn     = __phys_to_pfn(ZEUS_PC104IO_PHYS),
 		.length  = 0x00800000,
@@ -837,7 +900,7 @@ static void __init zeus_map_io(void)
 	PCFR = PCFR_OPDE | PCFR_DC_EN | PCFR_FS | PCFR_FP;
 }
 
-MACHINE_START(ARCOM_ZEUS, "Arcom ZEUS")
+MACHINE_START(ARCOM_ZEUS, "Arcom/Eurotech ZEUS")
 	/* Maintainer: Marc Zyngier <maz@misterjones.org> */
 	.phys_io	= 0x40000000,
 	.io_pg_offst	= ((io_p2v(0x40000000) >> 18) & 0xfffc),