[ARM] tegra: initial tegra support

v2: Fixes from Mike Rapoport
	- remove unused header files (mach/dma.h and mach/nand.h)
	- remove tegra 1 references from Makefile.boot

v2: fixes from Russell King
	- remove mach/io.h include from mach/iomap.h
	- fix whitespace in Kconfig

v2: from Colin Cross
	- fix invalid immediate in debug-macro.S

v3:
	- allow selection of multiple boards

Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>

1 files changed, 118 insertions, 0 deletions

diff --git a/arch/arm/mach-tegra/include/mach/entry-macro.S b/arch/arm/mach-tegra/include/mach/entry-macro.S
new file mode 100644
index 00000000000..2ba9e5c9d2f
--- /dev/null
+++ b/arch/arm/mach-tegra/include/mach/entry-macro.S
@@ -0,0 +1,118 @@
+/* arch/arm/mach-tegra/include/mach/entry-macro.S
+ *
+ * Copyright (C) 2009 Palm, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+#include <mach/iomap.h>
+#include <mach/io.h>
+
+#if defined(CONFIG_ARM_GIC)
+
+#include <asm/hardware/gic.h>
+
+	/* Uses the GIC interrupt controller built into the cpu */
+#define ICTRL_BASE (IO_CPU_VIRT + 0x100)
+
+	.macro	disable_fiq
+	.endm
+
+	.macro	get_irqnr_preamble, base, tmp
+	movw \base, #(ICTRL_BASE & 0x0000ffff)
+	movt \base, #((ICTRL_BASE & 0xffff0000) >> 16)
+	.endm
+
+	.macro  arch_ret_to_user, tmp1, tmp2
+	.endm
+
+	/*
+	 * The interrupt numbering scheme is defined in the
+	 * interrupt controller spec.  To wit:
+	 *
+	 * Interrupts 0-15 are IPI
+	 * 16-28 are reserved
+	 * 29-31 are local.  We allow 30 to be used for the watchdog.
+	 * 32-1020 are global
+	 * 1021-1022 are reserved
+	 * 1023 is "spurious" (no interrupt)
+	 *
+	 * For now, we ignore all local interrupts so only return an interrupt
+	 * if it's between 30 and 1020.  The test_for_ipi routine below will
+	 * pick up on IPIs.
+	 *
+	 * A simple read from the controller will tell us the number of the
+	 * highest priority enabled interrupt.  We then just need to check
+	 * whether it is in the valid range for an IRQ (30-1020 inclusive).
+	 */
+
+	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+	/* bits 12-10 = src CPU, 9-0 = int # */
+	ldr     \irqstat, [\base, #GIC_CPU_INTACK]
+
+	ldr		\tmp, =1021
+
+	bic     \irqnr, \irqstat, #0x1c00
+
+	cmp     \irqnr, #29
+	cmpcc	\irqnr, \irqnr
+	cmpne	\irqnr, \tmp
+	cmpcs	\irqnr, \irqnr
+
+	.endm
+
+	/* We assume that irqstat (the raw value of the IRQ acknowledge
+	 * register) is preserved from the macro above.
+	 * If there is an IPI, we immediately signal end of interrupt on the
+	 * controller, since this requires the original irqstat value which
+	 * we won't easily be able to recreate later.
+	 */
+
+	.macro test_for_ipi, irqnr, irqstat, base, tmp
+	bic	\irqnr, \irqstat, #0x1c00
+	cmp	\irqnr, #16
+	strcc	\irqstat, [\base, #GIC_CPU_EOI]
+	cmpcs	\irqnr, \irqnr
+	.endm
+
+	/* As above, this assumes that irqstat and base are preserved.. */
+
+	.macro test_for_ltirq, irqnr, irqstat, base, tmp
+	bic	\irqnr, \irqstat, #0x1c00
+	mov 	\tmp, #0
+	cmp	\irqnr, #29
+	moveq	\tmp, #1
+	streq	\irqstat, [\base, #GIC_CPU_EOI]
+	cmp	\tmp, #0
+	.endm
+
+#else
+	/* legacy interrupt controller for AP16 */
+	.macro	disable_fiq
+	.endm
+
+	.macro	get_irqnr_preamble, base, tmp
+	@ enable imprecise aborts
+	cpsie	a
+	@ EVP base at 0xf010f000
+	mov \base, #0xf0000000
+	orr \base, #0x00100000
+	orr \base, #0x0000f000
+	.endm
+
+	.macro	arch_ret_to_user, tmp1, tmp2
+	.endm
+
+	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+	ldr \irqnr, [\base, #0x20]	@ EVT_IRQ_STS
+	cmp \irqnr, #0x80
+	.endm
+#endif