powerpc/5200: dts: refactor dts files

This patch creates mpc5200b.dtsi containing the information for the MPC5200b
SoC then modifies all of the dts files for MPC5200b based systems to use
mpc5200b.dtsi.

Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

1 files changed, 22 insertions, 188 deletions

diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts
index 861f09ff3a7..48d72f38e5e 100644
--- a/arch/powerpc/boot/dts/media5200.dts
+++ b/arch/powerpc/boot/dts/media5200.dts
@@ -11,14 +11,11 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "fsl,media5200";
 	compatible = "fsl,media5200";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
 
 	aliases {
 		console = &console;
@@ -30,16 +27,7 @@
 	};
 
 	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;		// L1, 16K
-			i-cache-size = <0x4000>;		// L1, 16K
 			timebase-frequency = <33000000>;	// 33 MHz, these were configured by U-Boot
 			bus-frequency = <132000000>;		// 132 MHz
 			clock-frequency = <396000000>;		// 396 MHz
@@ -47,203 +35,57 @@
 	};
 
 	memory {
-		device_type = "memory";
 		reg = <0x00000000 0x08000000>;	// 128MB RAM
 	};
 
-	soc@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		reg = <0xf0000000 0x00000100>;
+	soc5200@f0000000 {
 		bus-frequency = <132000000>;// 132 MHz
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
 
 		timer@600 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
 			fsl,has-wdt;
 		};
 
-		timer@610 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
-		};
-
-		timer@620 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
-		};
-
-		timer@630 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
-		};
-
-		timer@640 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
-		};
-
-		timer@650 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
-		};
-
-		timer@660 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x660 0x10>;
-			interrupts = <1 15 0>;
-		};
-
-		timer@670 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
-		};
-
-		rtc@800 {	// Real time clock
-			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
-			reg = <0x800 0x100>;
-			interrupts = <1 5 0 1 6 0>;
-		};
-
-		can@900 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 17 0>;
-			reg = <0x900 0x80>;
+		psc@2000 {	// PSC1
+			status = "disabled";
 		};
 
-		can@980 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 18 0>;
-			reg = <0x980 0x80>;
+		psc@2200 {	// PSC2
+			status = "disabled";
 		};
 
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		psc@2400 {	// PSC3
+			status = "disabled";
 		};
 
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		psc@2600 {	// PSC4
+			status = "disabled";
 		};
 
-		spi@f00 {
-			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-			reg = <0xf00 0x20>;
-			interrupts = <2 13 0 2 14 0>;
-		};
-
-		usb@1000 {
-			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
-			reg = <0x1000 0x100>;
-			interrupts = <2 6 0>;
-		};
-
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
-		};
-
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
+		psc@2800 {	// PSC5
+			status = "disabled";
 		};
 
 		// PSC6 in uart mode
 		console: psc@2c00 {		// PSC6
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2c00 0x100>;
-			interrupts = <2 4 0>;
 		};
 
-		eth0: ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
+		ethernet@3000 {
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;	// fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;	// these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				reg = <0>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
-		};
-
-		i2c@3d00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d00 0x40>;
-			interrupts = <2 15 0>;
-		};
-
-		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
-		};
-
-		sram@8000 {
-			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
-			reg = <0x8000 0x4000>;
+		usb@1000 {
+			reg = <0x1000 0x100>;
 		};
 	};
 
 	pci@f0000d00 {
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		device_type = "pci";
-		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
-		reg = <0xf0000d00 0x100>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <0xc000 0 0 1 &media5200_fpga 0 2 // 1st slot
 				 0xc000 0 0 2 &media5200_fpga 0 3
@@ -260,37 +102,29 @@
 
 				 0xe000 0 0 1 &media5200_fpga 0 5 // CoralIP
 				>;
-		clock-frequency = <0>; // From boot loader
-		interrupts = <2 8 0 2 9 0 2 10 0>;
-		interrupt-parent = <&mpc5200_pic>;
-		bus-range = <0 0>;
 		ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
 			  0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
 			  0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
+		interrupt-parent = <&mpc5200_pic>;
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-		#address-cells = <2>;
-		#size-cells = <1>;
-
 		ranges = < 0 0 0xfc000000 0x02000000
 			   1 0 0xfe000000 0x02000000
 			   2 0 0xf0010000 0x00010000
 			   3 0 0xf0020000 0x00010000 >;
-
 		flash@0,0 {
 			compatible = "amd,am29lv28ml", "cfi-flash";
-			reg = <0 0x0 0x2000000>;		// 32 MB
-			bank-width = <4>;			// Width in bytes of the flash bank
-			device-width = <2>;			// Two devices on each bank
+			reg = <0 0x0 0x2000000>;                // 32 MB
+			bank-width = <4>;                       // Width in bytes of the flash bank
+			device-width = <2>;                     // Two devices on each bank
 		};
 
 		flash@1,0 {
 			compatible = "amd,am29lv28ml", "cfi-flash";
-			reg = <1 0 0x2000000>;			// 32 MB
-			bank-width = <4>;			// Width in bytes of the flash bank
-			device-width = <2>;			// Two devices on each bank
+			reg = <1 0 0x2000000>;                  // 32 MB
+			bank-width = <4>;                       // Width in bytes of the flash bank
+			device-width = <2>;                     // Two devices on each bank
 		};
 
 		media5200_fpga: fpga@2,0 {