diff options
| author | Kalle Valo <kvalo@qca.qualcomm.com> | 2013-09-01 11:22:14 +0300 |
|---|---|---|
| committer | Kalle Valo <kvalo@qca.qualcomm.com> | 2013-09-03 09:54:16 +0300 |
| commit | e01ae68c5d8889588db6b7fcf3e3d7821a3365fb (patch) | |
| tree | fc036fb91c1cfb78153aee39c1326e78acca2cff /drivers/net/wireless/ath/ath10k/hw.h | |
| parent | e9780367b0f43536b460fd83931f7c111ec99470 (diff) | |
ath10k: check chip id from the soc register during probe
ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.
To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:
[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95
Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.
Reported-by: Zaki Bakar <zaki.bm@gmail.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Diffstat (limited to 'drivers/net/wireless/ath/ath10k/hw.h')
| -rw-r--r-- | drivers/net/wireless/ath/ath10k/hw.h | 8 |
1 files changed, 8 insertions, 0 deletions
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h index 5708888486e..643f0c9f052 100644 --- a/drivers/net/wireless/ath/ath10k/hw.h +++ b/drivers/net/wireless/ath/ath10k/hw.h @@ -26,8 +26,12 @@ #define SUPPORTED_FW_RELEASE 0 #define SUPPORTED_FW_BUILD 636 +/* QCA988X 1.0 definitions (unsupported) */ +#define QCA988X_HW_1_0_CHIP_ID_REV 0x0 + /* QCA988X 2.0 definitions */ #define QCA988X_HW_2_0_VERSION 0x4100016c +#define QCA988X_HW_2_0_CHIP_ID_REV 0x2 #define QCA988X_HW_2_0_FW_DIR "ath10k/QCA988X/hw2.0" #define QCA988X_HW_2_0_FW_FILE "firmware.bin" #define QCA988X_HW_2_0_OTP_FILE "otp.bin" @@ -164,6 +168,10 @@ enum ath10k_mcast2ucast_mode { #define SOC_LPO_CAL_ENABLE_LSB 20 #define SOC_LPO_CAL_ENABLE_MASK 0x00100000 +#define SOC_CHIP_ID_ADDRESS 0x000000ec +#define SOC_CHIP_ID_REV_LSB 8 +#define SOC_CHIP_ID_REV_MASK 0x00000f00 + #define WLAN_RESET_CONTROL_COLD_RST_MASK 0x00000008 #define WLAN_RESET_CONTROL_WARM_RST_MASK 0x00000004 #define WLAN_SYSTEM_SLEEP_DISABLE_LSB 0 |