pcmcia: remove obsolete and wrong comments

What's worse than no comment? A wrong comment.

Several PCMCIA device drivers contained the same comments, which
were based on how the PCMCIA subsystem worked in the old days of 2.4.,
and which were originally part of a "dummy_cs" driver. These comments
no longer matched at all what is happening now, and therefore should
be removed.

Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>

1 files changed, 0 insertions, 44 deletions

diff --git a/drivers/net/wireless/orinoco/spectrum_cs.c b/drivers/net/wireless/orinoco/spectrum_cs.c
index 1314cf204f1..fb859a5ad2e 100644
--- a/drivers/net/wireless/orinoco/spectrum_cs.c
+++ b/drivers/net/wireless/orinoco/spectrum_cs.c
@@ -153,14 +153,6 @@ spectrum_cs_stop_firmware(struct orinoco_private *priv, int idle)
 /* PCMCIA stuff     						    */
 /********************************************************************/
 
-/*
- * This creates an "instance" of the driver, allocating local data
- * structures for one device.  The device is registered with Card
- * Services.
- *
- * The dev_link structure is initialized, but we don't actually
- * configure the card at this point -- we wait until we receive a card
- * insertion event.  */
 static int
 spectrum_cs_probe(struct pcmcia_device *link)
 {
@@ -181,12 +173,6 @@ spectrum_cs_probe(struct pcmcia_device *link)
 	return spectrum_cs_config(link);
 }				/* spectrum_cs_attach */
 
-/*
- * This deletes a driver "instance".  The device is de-registered with
- * Card Services.  If it has been released, all local data structures
- * are freed.  Otherwise, the structures will be freed when the device
- * is released.
- */
 static void spectrum_cs_detach(struct pcmcia_device *link)
 {
 	struct orinoco_private *priv = link->priv;
@@ -198,12 +184,6 @@ static void spectrum_cs_detach(struct pcmcia_device *link)
 	free_orinocodev(priv);
 }				/* spectrum_cs_detach */
 
-/*
- * spectrum_cs_config() is scheduled to run after a CARD_INSERTION
- * event is received, to configure the PCMCIA socket, and to make the
- * device available to the system.
- */
-
 static int spectrum_cs_config_check(struct pcmcia_device *p_dev,
 				    void *priv_data)
 {
@@ -221,20 +201,6 @@ spectrum_cs_config(struct pcmcia_device *link)
 	int ret;
 	void __iomem *mem;
 
-	/*
-	 * In this loop, we scan the CIS for configuration table
-	 * entries, each of which describes a valid card
-	 * configuration, including voltage, IO window, memory window,
-	 * and interrupt settings.
-	 *
-	 * We make no assumptions about the card to be configured: we
-	 * use just the information available in the CIS.  In an ideal
-	 * world, this would work for any PCMCIA card, but it requires
-	 * a complete and accurate CIS.  In practice, a driver usually
-	 * "knows" most of these things without consulting the CIS,
-	 * and most client drivers will only use the CIS to fill in
-	 * implementation-defined details.
-	 */
 	link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC |
 		CONF_AUTO_SET_IO | CONF_ENABLE_IRQ;
 	if (ignore_cis_vcc)
@@ -263,11 +229,6 @@ spectrum_cs_config(struct pcmcia_device *link)
 	hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING);
 	hw->eeprom_pda = true;
 
-	/*
-	 * This actually configures the PCMCIA socket -- setting up
-	 * the I/O windows and the interrupt mapping, and putting the
-	 * card and host interface into "Memory and IO" mode.
-	 */
 	ret = pcmcia_enable_device(link);
 	if (ret)
 		goto failed;
@@ -296,11 +257,6 @@ spectrum_cs_config(struct pcmcia_device *link)
 	return -ENODEV;
 }				/* spectrum_cs_config */
 
-/*
- * After a card is removed, spectrum_cs_release() will unregister the
- * device, and release the PCMCIA configuration.  If the device is
- * still open, this will be postponed until it is closed.
- */
 static void
 spectrum_cs_release(struct pcmcia_device *link)
 {