Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 128 insertions, 0 deletions

diff --git a/include/asm-v850/rte_ma1_cb.h b/include/asm-v850/rte_ma1_cb.h
new file mode 100644
index 00000000000..bd3162ab984
--- /dev/null
+++ b/include/asm-v850/rte_ma1_cb.h
@@ -0,0 +1,128 @@
+/*
+ * include/asm-v850/rte_ma1_cb.h -- Midas labs RTE-V850/MA1-CB board
+ *
+ *  Copyright (C) 2001,02,03  NEC Electronics Corporation
+ *  Copyright (C) 2001,02,03  Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ */
+
+#ifndef __V850_RTE_MA1_CB_H__
+#define __V850_RTE_MA1_CB_H__
+
+#include <asm/rte_cb.h>		/* Common defs for Midas RTE-CB boards.  */
+
+
+#define PLATFORM		"rte-v850e/ma1-cb"
+#define PLATFORM_LONG		"Midas lab RTE-V850E/MA1-CB"
+
+#define CPU_CLOCK_FREQ		50000000 /* 50MHz */
+
+/* 1MB of onboard SRAM.  Note that the monitor ROM uses parts of this
+   for its own purposes, so care must be taken.  Some address lines are
+   not decoded, so the SRAM area is mirrored every 1MB from 0x400000 to
+   0x800000 (exclusive).  */
+#define SRAM_ADDR		0x00400000
+#define SRAM_SIZE		0x00100000 /* 1MB */
+
+/* 32MB of onbard SDRAM.  */
+#define SDRAM_ADDR		0x00800000
+#define SDRAM_SIZE		0x02000000 /* 32MB */
+
+
+/* CPU addresses of GBUS memory spaces.  */
+#define GCS0_ADDR		0x05000000 /* GCS0 - Common SRAM (2MB) */
+#define GCS0_SIZE		0x00200000 /*   2MB */
+#define GCS1_ADDR		0x06000000 /* GCS1 - Flash ROM (8MB) */
+#define GCS1_SIZE		0x00800000 /*   8MB */
+#define GCS2_ADDR		0x07900000 /* GCS2 - I/O registers */
+#define GCS2_SIZE		0x00400000 /*   4MB */
+#define GCS5_ADDR		0x04000000 /* GCS5 - PCI bus space */
+#define GCS5_SIZE		0x01000000 /*   16MB */
+#define GCS6_ADDR		0x07980000 /* GCS6 - PCI control registers */
+#define GCS6_SIZE		0x00000200 /*   512B */
+
+
+/* For <asm/page.h> */
+#define PAGE_OFFSET 		SRAM_ADDR
+
+
+/* The GBUS GINT0 - GINT3 interrupts are connected to the INTP000 - INTP011
+   pins on the CPU.  These are shared among the GBUS interrupts.  */
+#define IRQ_GINT(n)		IRQ_INTP(n)
+#define IRQ_GINT_NUM		4
+
+/* Used by <asm/rte_cb.h> to derive NUM_MACH_IRQS.  */
+#define NUM_RTE_CB_IRQS		NUM_CPU_IRQS
+
+
+#ifdef CONFIG_ROM_KERNEL
+/* Kernel is in ROM, starting at address 0.  */
+
+#define INTV_BASE		0
+
+#else /* !CONFIG_ROM_KERNEL */
+
+#ifdef CONFIG_RTE_CB_MULTI
+/* Using RAM kernel with ROM monitor for Multi debugger.  */
+
+/* The chip's real interrupt vectors are in ROM, but they jump to a
+   secondary interrupt vector table in RAM.  */
+#define INTV_BASE		0x004F8000
+
+/* Scratch memory used by the ROM monitor, which shouldn't be used by
+   linux (except for the alternate interrupt vector area, defined
+   above).  */
+#define MON_SCRATCH_ADDR	0x004F8000
+#define MON_SCRATCH_SIZE	0x00008000 /* 32KB */
+
+#else /* !CONFIG_RTE_CB_MULTI */
+/* Using RAM-kernel.  Assume some sort of boot-loader got us loaded at
+   address 0.  */
+
+#define INTV_BASE		0
+
+#endif /* CONFIG_RTE_CB_MULTI */
+
+#endif /* CONFIG_ROM_KERNEL */
+
+
+/* Some misc. on-board devices.  */
+
+/* Seven-segment LED display (two digits).  Write-only.  */
+#define LED_ADDR(n)		(0x07802000 + (n))
+#define LED(n)			(*(volatile unsigned char *)LED_ADDR(n))
+#define LED_NUM_DIGITS		2
+
+
+/* Override the basic MA uart pre-initialization so that we can
+   initialize extra stuff.  */
+#undef V850E_UART_PRE_CONFIGURE	/* should be defined by <asm/ma.h> */
+#define V850E_UART_PRE_CONFIGURE	rte_ma1_cb_uart_pre_configure
+#ifndef __ASSEMBLY__
+extern void rte_ma1_cb_uart_pre_configure (unsigned chan,
+					   unsigned cflags, unsigned baud);
+#endif
+
+/* This board supports RTS/CTS for the on-chip UART, but only for channel 0. */
+
+/* CTS for UART channel 0 is pin P43 (bit 3 of port 4).  */
+#define V850E_UART_CTS(chan)	((chan) == 0 ? !(MA_PORT4_IO & 0x8) : 1)
+/* RTS for UART channel 0 is pin P42 (bit 2 of port 4).  */
+#define V850E_UART_SET_RTS(chan, val)					      \
+   do {									      \
+	   if (chan == 0) {						      \
+		   unsigned old = MA_PORT4_IO; 				      \
+		   if (val)						      \
+			   MA_PORT4_IO = old & ~0x4;			      \
+		   else							      \
+			   MA_PORT4_IO = old | 0x4;			      \
+	   }								      \
+   } while (0)
+
+
+#endif /* __V850_RTE_MA1_CB_H__ */