diff options
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_driver.c | 17 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_iba6110.c | 117 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_iba6120.c | 8 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_intr.c | 10 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_kernel.h | 4 |
5 files changed, 74 insertions, 82 deletions
diff --git a/drivers/infiniband/hw/ipath/ipath_driver.c b/drivers/infiniband/hw/ipath/ipath_driver.c index b4ffaa7bcbb..09a13c1fc46 100644 --- a/drivers/infiniband/hw/ipath/ipath_driver.c +++ b/drivers/infiniband/hw/ipath/ipath_driver.c @@ -304,7 +304,7 @@ static int __devinit ipath_init_one(struct pci_dev *pdev, } addr = pci_resource_start(pdev, 0); len = pci_resource_len(pdev, 0); - ipath_cdbg(VERBOSE, "regbase (0) %llx len %d irq %x, vend %x/%x " + ipath_cdbg(VERBOSE, "regbase (0) %llx len %d pdev->irq %d, vend %x/%x " "driver_data %lx\n", addr, len, pdev->irq, ent->vendor, ent->device, ent->driver_data); @@ -467,15 +467,15 @@ static int __devinit ipath_init_one(struct pci_dev *pdev, * check 0 irq after we return from chip-specific bus setup, since * that can affect this due to setup */ - if (!pdev->irq) + if (!dd->ipath_irq) ipath_dev_err(dd, "irq is 0, BIOS error? Interrupts won't " "work\n"); else { - ret = request_irq(pdev->irq, ipath_intr, IRQF_SHARED, + ret = request_irq(dd->ipath_irq, ipath_intr, IRQF_SHARED, IPATH_DRV_NAME, dd); if (ret) { ipath_dev_err(dd, "Couldn't setup irq handler, " - "irq=%u: %d\n", pdev->irq, ret); + "irq=%d: %d\n", dd->ipath_irq, ret); goto bail_iounmap; } } @@ -637,11 +637,10 @@ static void __devexit ipath_remove_one(struct pci_dev *pdev) * free up port 0 (kernel) rcvhdr, egr bufs, and eventually tid bufs * for all versions of the driver, if they were allocated */ - if (pdev->irq) { - ipath_cdbg(VERBOSE, - "unit %u free_irq of irq %x\n", - dd->ipath_unit, pdev->irq); - free_irq(pdev->irq, dd); + if (dd->ipath_irq) { + ipath_cdbg(VERBOSE, "unit %u free irq %d\n", + dd->ipath_unit, dd->ipath_irq); + dd->ipath_f_free_irq(dd); } else ipath_dbg("irq is 0, not doing free_irq " "for unit %u\n", dd->ipath_unit); diff --git a/drivers/infiniband/hw/ipath/ipath_iba6110.c b/drivers/infiniband/hw/ipath/ipath_iba6110.c index 9e4e8d4c6e2..e57c7a351cb 100644 --- a/drivers/infiniband/hw/ipath/ipath_iba6110.c +++ b/drivers/infiniband/hw/ipath/ipath_iba6110.c @@ -38,6 +38,7 @@ #include <linux/pci.h> #include <linux/delay.h> +#include <linux/htirq.h> #include "ipath_kernel.h" #include "ipath_registers.h" @@ -913,49 +914,40 @@ static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev, } } -static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev, - int pos) +static int ipath_ht_intconfig(struct ipath_devdata *dd) { - u32 int_handler_addr_lower; - u32 int_handler_addr_upper; - u64 ihandler; - u32 intvec; + int ret; - /* use indirection register to get the intr handler */ - pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10); - pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower); - pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11); - pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper); + if (dd->ipath_intconfig) { + ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig, + dd->ipath_intconfig); /* interrupt address */ + ret = 0; + } else { + ipath_dev_err(dd, "No interrupts enabled, couldn't setup " + "interrupt address\n"); + ret = -EINVAL; + } - ihandler = (u64) int_handler_addr_lower | - ((u64) int_handler_addr_upper << 32); + return ret; +} + +static void ipath_ht_irq_update(struct pci_dev *dev, int irq, + struct ht_irq_msg *msg) +{ + struct ipath_devdata *dd = pci_get_drvdata(dev); + u64 prev_intconfig = dd->ipath_intconfig; + + dd->ipath_intconfig = msg->address_lo; + dd->ipath_intconfig |= ((u64) msg->address_hi) << 32; /* - * kernels with CONFIG_PCI_MSI set the vector in the irq field of - * struct pci_device, so we use that to program the internal - * interrupt register (not config space) with that value. The BIOS - * must still have done the basic MSI setup. - */ - intvec = pdev->irq; - /* - * clear any vector bits there; normally not set but we'll overload - * this for some debug purposes (setting the HTC debug register - * value from software, rather than GPIOs), so it might be set on a - * driver reload. + * If the previous value of dd->ipath_intconfig is zero, we're + * getting configured for the first time, and must not program the + * intconfig register here (it will be programmed later, when the + * hardware is ready). Otherwise, we should. */ - ihandler &= ~0xff0000; - /* x86 vector goes in intrinfo[23:16] */ - ihandler |= intvec << 16; - ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, " - "interruptconfig %llx\n", int_handler_addr_lower, - int_handler_addr_upper, intvec, - (unsigned long long) ihandler); - - /* can't program yet, so save for interrupt setup */ - dd->ipath_intconfig = ihandler; - /* keep going, so we find link control stuff also */ - - return ihandler != 0; + if (prev_intconfig) + ipath_ht_intconfig(dd); } /** @@ -971,12 +963,19 @@ static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev, static int ipath_setup_ht_config(struct ipath_devdata *dd, struct pci_dev *pdev) { - int pos, ret = 0; - int ihandler = 0; + int pos, ret; + + ret = __ht_create_irq(pdev, 0, ipath_ht_irq_update); + if (ret < 0) { + ipath_dev_err(dd, "Couldn't create interrupt handler: " + "err %d\n", ret); + goto bail; + } + dd->ipath_irq = ret; + ret = 0; /* - * Read the capability info to find the interrupt info, and also - * handle clearing CRC errors in linkctrl register if necessary. We + * Handle clearing CRC errors in linkctrl register if necessary. We * do this early, before we ever enable errors or hardware errors, * mostly to avoid causing the chip to enter freeze mode. */ @@ -1000,17 +999,9 @@ static int ipath_setup_ht_config(struct ipath_devdata *dd, } if (!(cap_type & 0xE0)) slave_or_pri_blk(dd, pdev, pos, cap_type); - else if (cap_type == HT_INTR_DISC_CONFIG) - ihandler = set_int_handler(dd, pdev, pos); } while ((pos = pci_find_next_capability(pdev, pos, PCI_CAP_ID_HT))); - if (!ihandler) { - ipath_dev_err(dd, "Couldn't find interrupt handler in " - "config space\n"); - ret = -ENODEV; - } - bail: return ret; } @@ -1360,25 +1351,6 @@ static void ipath_ht_quiet_serdes(struct ipath_devdata *dd) ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val); } -static int ipath_ht_intconfig(struct ipath_devdata *dd) -{ - int ret; - - if (!dd->ipath_intconfig) { - ipath_dev_err(dd, "No interrupts enabled, couldn't setup " - "interrupt address\n"); - ret = 1; - goto bail; - } - - ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig, - dd->ipath_intconfig); /* interrupt address */ - ret = 0; - -bail: - return ret; -} - /** * ipath_pe_put_tid - write a TID in chip * @dd: the infinipath device @@ -1575,6 +1547,14 @@ static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase) return 0; } +static void ipath_ht_free_irq(struct ipath_devdata *dd) +{ + free_irq(dd->ipath_irq, dd); + ht_destroy_irq(dd->ipath_irq); + dd->ipath_irq = 0; + dd->ipath_intconfig = 0; +} + /** * ipath_init_iba6110_funcs - set up the chip-specific function pointers * @dd: the infinipath device @@ -1598,6 +1578,7 @@ void ipath_init_iba6110_funcs(struct ipath_devdata *dd) dd->ipath_f_cleanup = ipath_setup_ht_cleanup; dd->ipath_f_setextled = ipath_setup_ht_setextled; dd->ipath_f_get_base_info = ipath_ht_get_base_info; + dd->ipath_f_free_irq = ipath_ht_free_irq; /* * initialize chip-specific variables diff --git a/drivers/infiniband/hw/ipath/ipath_iba6120.c b/drivers/infiniband/hw/ipath/ipath_iba6120.c index a72ab9de386..6af89683f71 100644 --- a/drivers/infiniband/hw/ipath/ipath_iba6120.c +++ b/drivers/infiniband/hw/ipath/ipath_iba6120.c @@ -851,6 +851,7 @@ static int ipath_setup_pe_config(struct ipath_devdata *dd, int pos, ret; dd->ipath_msi_lo = 0; /* used as a flag during reset processing */ + dd->ipath_irq = pdev->irq; ret = pci_enable_msi(dd->pcidev); if (ret) ipath_dev_err(dd, "pci_enable_msi failed: %d, " @@ -1323,6 +1324,12 @@ done: return 0; } +static void ipath_pe_free_irq(struct ipath_devdata *dd) +{ + free_irq(dd->ipath_irq, dd); + dd->ipath_irq = 0; +} + /** * ipath_init_iba6120_funcs - set up the chip-specific function pointers * @dd: the infinipath device @@ -1349,6 +1356,7 @@ void ipath_init_iba6120_funcs(struct ipath_devdata *dd) dd->ipath_f_cleanup = ipath_setup_pe_cleanup; dd->ipath_f_setextled = ipath_setup_pe_setextled; dd->ipath_f_get_base_info = ipath_pe_get_base_info; + dd->ipath_f_free_irq = ipath_pe_free_irq; /* initialize chip-specific variables */ dd->ipath_f_tidtemplate = ipath_pe_tidtemplate; diff --git a/drivers/infiniband/hw/ipath/ipath_intr.c b/drivers/infiniband/hw/ipath/ipath_intr.c index d9079ee1203..5652a550d44 100644 --- a/drivers/infiniband/hw/ipath/ipath_intr.c +++ b/drivers/infiniband/hw/ipath/ipath_intr.c @@ -710,14 +710,14 @@ static void ipath_bad_intr(struct ipath_devdata *dd, u32 * unexpectp) * linuxbios development work, and it may happen in * the future again. */ - if (dd->pcidev && dd->pcidev->irq) { + if (dd->pcidev && dd->ipath_irq) { ipath_dev_err(dd, "Now %u unexpected " "interrupts, unregistering " "interrupt handler\n", *unexpectp); - ipath_dbg("free_irq of irq %x\n", - dd->pcidev->irq); - free_irq(dd->pcidev->irq, dd); + ipath_dbg("free_irq of irq %d\n", + dd->ipath_irq); + dd->ipath_f_free_irq(dd); } } if (ipath_read_kreg32(dd, dd->ipath_kregs->kr_intmask)) { @@ -753,7 +753,7 @@ static void ipath_bad_regread(struct ipath_devdata *dd) if (allbits == 2) { ipath_dev_err(dd, "Still bad interrupt status, " "unregistering interrupt\n"); - free_irq(dd->pcidev->irq, dd); + dd->ipath_f_free_irq(dd); } else if (allbits > 2) { if ((allbits % 10000) == 0) printk("."); diff --git a/drivers/infiniband/hw/ipath/ipath_kernel.h b/drivers/infiniband/hw/ipath/ipath_kernel.h index 06d5020a2f6..986b2125b8f 100644 --- a/drivers/infiniband/hw/ipath/ipath_kernel.h +++ b/drivers/infiniband/hw/ipath/ipath_kernel.h @@ -213,6 +213,8 @@ struct ipath_devdata { void (*ipath_f_setextled)(struct ipath_devdata *, u64, u64); /* fill out chip-specific fields */ int (*ipath_f_get_base_info)(struct ipath_portdata *, void *); + /* free irq */ + void (*ipath_f_free_irq)(struct ipath_devdata *); struct ipath_ibdev *verbs_dev; struct timer_list verbs_timer; /* total dwords sent (summed from counter) */ @@ -328,6 +330,8 @@ struct ipath_devdata { /* so we can rewrite it after a chip reset */ u32 ipath_pcibar1; + /* interrupt number */ + int ipath_irq; /* HT/PCI Vendor ID (here for NodeInfo) */ u16 ipath_vendorid; /* HT/PCI Device ID (here for NodeInfo) */ |