diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 36 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 5216b419016..8b4f7b7fe88 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -9,6 +9,18 @@ Required Properties: - reg: physical base address of the controller and length of memory mapped region. +Optional Properties: +- clocks: List of clock handles. The parent clocks of the input clocks to the + devices in this power domain are set to oscclk before power gating + and restored back after powering on a domain. This is required for + all domains which are powered on and off and not required for unused + domains. +- clock-names: The following clocks can be specified: + - oscclk: Oscillator clock. + - pclkN, clkN: Pairs of parent of input clock and input clock to the + devices in this power domain. Maximum of 4 pairs (N = 0 to 3) + are supported currently. + Node of a device using power domains must have a samsung,power-domain property defined with a phandle to respective power domain. @@ -19,6 +31,14 @@ Example: reg = <0x10023C00 0x10>; }; + mfc_pd: power-domain@10044060 { + compatible = "samsung,exynos4210-pd"; + reg = <0x10044060 0x20>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_SW_ACLK333>, + <&clock CLK_MOUT_USER_ACLK333>; + clock-names = "oscclk", "pclk0", "clk0"; + }; + Example of the node using power domain: node { diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index b513cb8196f..af527ee111c 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -40,6 +40,9 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length of window to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. +- arm,io-coherent : indicates that the system is operating in an hardware + I/O coherent mode. Valid only when the arm,pl310-cache compatible + string is used. - interrupts : 1 combined interrupt. - cache-id-part: cache id part number to be used if it is not present on hardware diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 64fd7dec1bb..b3556609a06 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -4,6 +4,13 @@ Required properties: - compatible: Must contain one of the following: + - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. + - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. + - "renesas,scifa-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFA compatible UART. + - "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART. + - "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART. + - "renesas,scifb-r8a7740" for R8A7740 (R-Mobile A1) SCIFB compatible UART. + - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt index b82a268f1bd..bee6ff204ba 100644 --- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt @@ -23,6 +23,12 @@ Optional properties: - spi-max-frequency: Specifies maximum SPI clock frequency, Units - Hz. Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt +- num-cs: total number of chipselects +- cs-gpios: should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child + nodes. If unspecified, a single SPI device without a chip + select can be used. + SPI slave nodes must be children of the SPI master node and can contain properties described in Documentation/devicetree/bindings/spi/spi-bus.txt |