diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/leds/tca6507.txt | 16 | ||||
| -rw-r--r-- | Documentation/leds/leds-lp55xx.txt | 10 |
2 files changed, 25 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/leds/tca6507.txt b/Documentation/devicetree/bindings/leds/tca6507.txt index 80ff3dfb1f3..d7221b84987 100644 --- a/Documentation/devicetree/bindings/leds/tca6507.txt +++ b/Documentation/devicetree/bindings/leds/tca6507.txt @@ -2,6 +2,13 @@ LEDs connected to tca6507 Required properties: - compatible : should be : "ti,tca6507". +- #address-cells: must be 1 +- #size-cells: must be 0 +- reg: typically 0x45. + +Optional properties: +- gpio-controller: allows lines to be used as output-only GPIOs. +- #gpio-cells: if present, must be 0. Each led is represented as a sub-node of the ti,tca6507 device. @@ -10,6 +17,7 @@ LED sub-node properties: - reg : number of LED line (could be from 0 to 6) - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt +- compatible: either "led" (the default) or "gpio". Examples: @@ -19,6 +27,9 @@ tca6507@45 { #size-cells = <0>; reg = <0x45>; + gpio-controller; + #gpio-cells = <2>; + led0: red-aux@0 { label = "red:aux"; reg = <0x0>; @@ -29,5 +40,10 @@ tca6507@45 { reg = <0x5>; linux,default-trigger = "default-on"; }; + + wifi-reset@6 { + reg = <0x6>; + compatible = "gpio"; + }; }; diff --git a/Documentation/leds/leds-lp55xx.txt b/Documentation/leds/leds-lp55xx.txt index 82713ff92eb..bcea12a0c58 100644 --- a/Documentation/leds/leds-lp55xx.txt +++ b/Documentation/leds/leds-lp55xx.txt @@ -73,6 +73,10 @@ select_engine : Select which engine is used for running program run_engine : Start program which is loaded via the firmware interface firmware : Load program data +In case of LP5523, one more command is required, 'enginex_leds'. +It is used for selecting LED output(s) at each engine number. +In more details, please refer to 'leds-lp5523.txt'. + For example, run blinking pattern in engine #1 of LP5521 echo 1 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading @@ -81,10 +85,12 @@ echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine For example, run blinking pattern in engine #3 of LP55231 +Two LEDs are configured as pattern output channels. echo 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp55231/loading echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data echo 0 > /sys/class/firmware/lp55231/loading +echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds echo 1 > /sys/bus/i2c/devices/xxxx/run_engine To start blinking patterns in engine #2 and #3 simultaneously, @@ -99,17 +105,19 @@ done echo 1 > /sys/class/leds/red/device/run_engine Here is another example for LP5523. +Full LED strings are selected by 'engine2_leds'. echo 2 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5523/loading echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data echo 0 > /sys/class/firmware/lp5523/loading +echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. -The pattern sqeuence of LP8501 is same as LP5523. +The pattern sqeuence of LP8501 is similar to LP5523. However pattern data is specific. Ex 1) Engine 1 is used echo 1 > /sys/bus/i2c/devices/xxxx/select_engine |