1 files changed, 89 insertions, 0 deletions
diff --git a/arch/arm/mach-ux500/include/mach/entry-macro.S b/arch/arm/mach-ux500/include/mach/entry-macro.S
new file mode 100644
index 00000000000..eece3301fef
--- /dev/null
+++ b/arch/arm/mach-ux500/include/mach/entry-macro.S
@@ -0,0 +1,89 @@
+/*
+ * Low-level IRQ helper macros for U8500 platforms
+ *
+ * Copyright (C) 2009 ST-Ericsson.
+ *
+ * This file is a copy of ARM Realview platform.
+ *	-just satisfied checkpatch script.
+ *
+ * This file is licensed under  the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <mach/hardware.h>
+#include <asm/hardware/gic.h>
+
+		.macro	disable_fiq
+		.endm
+
+		.macro  get_irqnr_preamble, base, tmp
+		ldr     \base, =IO_ADDRESS(U8500_GIC_CPU_BASE)
+		.endm
+
+		.macro  arch_ret_to_user, tmp1, tmp2
+		.endm
+
+		/*
+		 * The interrupt numbering scheme is defined in the
+		 * interrupt controller spec.  To wit:
+		 *
+		 * Interrupts 0-15 are IPI
+		 * 16-28 are reserved
+		 * 29-31 are local.  We allow 30 to be used for the watchdog.
+		 * 32-1020 are global
+		 * 1021-1022 are reserved
+		 * 1023 is "spurious" (no interrupt)
+		 *
+		 * For now, we ignore all local interrupts so only return an
+		 * interrupt if it's between 30 and 1020. The test_for_ipi
+		 * routine below will pick up on IPIs.
+		 *
+		 * A simple read from the controller will tell us the number
+		 * of the highest priority enabled interrupt. We then just
+		 * need to check whether it is in the valid range for an
+		 * IRQ (30-1020 inclusive).
+		 */
+
+		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+		/* bits 12-10 = src CPU, 9-0 = int # */
+		ldr     \irqstat, [\base, #GIC_CPU_INTACK]
+
+		ldr	\tmp, =1021
+
+		bic     \irqnr, \irqstat, #0x1c00
+
+		cmp     \irqnr, #29
+		cmpcc	\irqnr, \irqnr
+		cmpne	\irqnr, \tmp
+		cmpcs	\irqnr, \irqnr
+
+		.endm
+
+		/* We assume that irqstat (the raw value of the IRQ
+		 * acknowledge register) is preserved from the macro above.
+		 * If there is an IPI, we immediately signal end of
+		 * interrupt on the controller, since this requires the
+		 * original irqstat value which we won't easily be able
+		 * to recreate later.
+		 */
+
+		.macro test_for_ipi, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		cmp	\irqnr, #16
+		strcc	\irqstat, [\base, #GIC_CPU_EOI]
+		cmpcs	\irqnr, \irqnr
+		.endm
+
+		/* As above, this assumes that irqstat and base
+		 * are preserved..
+		 */
+
+		.macro test_for_ltirq, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		mov 	\tmp, #0
+		cmp	\irqnr, #29
+		moveq	\tmp, #1
+		streq	\irqstat, [\base, #GIC_CPU_EOI]
+		cmp	\tmp, #0
+		.endm